The user (or an init script) may setup RShunt via sysfs after the
driver was initialized, for instance based on the EEPROM contents
of a modular probe. The calibration register must be set accordingly.
Signed-off-by: Marc Titinger <[email protected]>
---
v2 of http://www.spinics.net/lists/linux-iio/msg23402.html:
- remove unnecessary line insertions
- cleanup leftover unused variable (build warning)
- patch 2/2 is unchanged (see v1)
---
drivers/iio/adc/ina2xx-adc.c | 39 ++++++++++++++++++++++++---------------
1 file changed, 24 insertions(+), 15 deletions(-)
diff --git a/drivers/iio/adc/ina2xx-adc.c b/drivers/iio/adc/ina2xx-adc.c
index 65909d5..4e56fe3 100644
--- a/drivers/iio/adc/ina2xx-adc.c
+++ b/drivers/iio/adc/ina2xx-adc.c
@@ -350,6 +350,23 @@ static ssize_t ina2xx_allow_async_readout_store(struct device *dev,
return len;
}
+/*
+ * Set current LSB to 1mA, shunt is in uOhms
+ * (equation 13 in datasheet). We hardcode a Current_LSB
+ * of 1.0 x10-6. The only remaining parameter is RShunt.
+ * There is no need to expose the CALIBRATION register
+ * to the user for now. But we need to reset this register
+ * if the user updates RShunt after driver init, e.g upon
+ * reading an EEPROM/Probe-type value.
+ */
+static int ina2xx_set_calibration(struct ina2xx_chip_info *chip)
+{
+ u16 regval = DIV_ROUND_CLOSEST(chip->config->calibration_factor,
+ chip->shunt_resistor);
+
+ return regmap_write(chip->regmap, INA2XX_CALIBRATION, regval);
+}
+
static int set_shunt_resistor(struct ina2xx_chip_info *chip, unsigned int val)
{
if (val <= 0 || val > chip->config->calibration_factor)
@@ -385,6 +402,11 @@ static ssize_t ina2xx_shunt_resistor_store(struct device *dev,
if (ret)
return ret;
+ /* Update the Calibration register */
+ ret = ina2xx_set_calibration(chip);
+ if (ret)
+ return ret;
+
return len;
}
@@ -602,24 +624,11 @@ static const struct iio_info ina2xx_info = {
/* Initialize the configuration and calibration registers. */
static int ina2xx_init(struct ina2xx_chip_info *chip, unsigned int config)
{
- u16 regval;
- int ret;
-
- ret = regmap_write(chip->regmap, INA2XX_CONFIG, config);
+ int ret = regmap_write(chip->regmap, INA2XX_CONFIG, config);
if (ret)
return ret;
- /*
- * Set current LSB to 1mA, shunt is in uOhms
- * (equation 13 in datasheet). We hardcode a Current_LSB
- * of 1.0 x10-6. The only remaining parameter is RShunt.
- * There is no need to expose the CALIBRATION register
- * to the user for now.
- */
- regval = DIV_ROUND_CLOSEST(chip->config->calibration_factor,
- chip->shunt_resistor);
-
- return regmap_write(chip->regmap, INA2XX_CALIBRATION, regval);
+ return ina2xx_set_calibration(chip);
}
static int ina2xx_probe(struct i2c_client *client,
--
2.5.0
On 14/03/16 10:20, Marc Titinger wrote:
> The user (or an init script) may setup RShunt via sysfs after the
> driver was initialized, for instance based on the EEPROM contents
> of a modular probe. The calibration register must be set accordingly.
>
> Signed-off-by: Marc Titinger <[email protected]>
> ---
> v2 of http://www.spinics.net/lists/linux-iio/msg23402.html:
>
> - remove unnecessary line insertions
> - cleanup leftover unused variable (build warning)
> - patch 2/2 is unchanged (see v1)
Err, can't find it for some reason.
Anyhow, applied this one to the togreg branch of iio.git - pushed
out as testing for the autobuilders to play with it.
Thanks,
Jonathan
> ---
> drivers/iio/adc/ina2xx-adc.c | 39 ++++++++++++++++++++++++---------------
> 1 file changed, 24 insertions(+), 15 deletions(-)
>
> diff --git a/drivers/iio/adc/ina2xx-adc.c b/drivers/iio/adc/ina2xx-adc.c
> index 65909d5..4e56fe3 100644
> --- a/drivers/iio/adc/ina2xx-adc.c
> +++ b/drivers/iio/adc/ina2xx-adc.c
> @@ -350,6 +350,23 @@ static ssize_t ina2xx_allow_async_readout_store(struct device *dev,
> return len;
> }
>
> +/*
> + * Set current LSB to 1mA, shunt is in uOhms
> + * (equation 13 in datasheet). We hardcode a Current_LSB
> + * of 1.0 x10-6. The only remaining parameter is RShunt.
> + * There is no need to expose the CALIBRATION register
> + * to the user for now. But we need to reset this register
> + * if the user updates RShunt after driver init, e.g upon
> + * reading an EEPROM/Probe-type value.
> + */
> +static int ina2xx_set_calibration(struct ina2xx_chip_info *chip)
> +{
> + u16 regval = DIV_ROUND_CLOSEST(chip->config->calibration_factor,
> + chip->shunt_resistor);
> +
> + return regmap_write(chip->regmap, INA2XX_CALIBRATION, regval);
> +}
> +
> static int set_shunt_resistor(struct ina2xx_chip_info *chip, unsigned int val)
> {
> if (val <= 0 || val > chip->config->calibration_factor)
> @@ -385,6 +402,11 @@ static ssize_t ina2xx_shunt_resistor_store(struct device *dev,
> if (ret)
> return ret;
>
> + /* Update the Calibration register */
> + ret = ina2xx_set_calibration(chip);
> + if (ret)
> + return ret;
> +
> return len;
> }
>
> @@ -602,24 +624,11 @@ static const struct iio_info ina2xx_info = {
> /* Initialize the configuration and calibration registers. */
> static int ina2xx_init(struct ina2xx_chip_info *chip, unsigned int config)
> {
> - u16 regval;
> - int ret;
> -
> - ret = regmap_write(chip->regmap, INA2XX_CONFIG, config);
> + int ret = regmap_write(chip->regmap, INA2XX_CONFIG, config);
> if (ret)
> return ret;
>
> - /*
> - * Set current LSB to 1mA, shunt is in uOhms
> - * (equation 13 in datasheet). We hardcode a Current_LSB
> - * of 1.0 x10-6. The only remaining parameter is RShunt.
> - * There is no need to expose the CALIBRATION register
> - * to the user for now.
> - */
> - regval = DIV_ROUND_CLOSEST(chip->config->calibration_factor,
> - chip->shunt_resistor);
> -
> - return regmap_write(chip->regmap, INA2XX_CALIBRATION, regval);
> + return ina2xx_set_calibration(chip);
> }
>
> static int ina2xx_probe(struct i2c_client *client,
>
On 20/03/2016 12:24, Jonathan Cameron wrote:
> On 14/03/16 10:20, Marc Titinger wrote:
>> The user (or an init script) may setup RShunt via sysfs after the
>> driver was initialized, for instance based on the EEPROM contents
>> of a modular probe. The calibration register must be set accordingly.
>>
>> Signed-off-by: Marc Titinger <[email protected]>
>> ---
>> v2 of http://www.spinics.net/lists/linux-iio/msg23402.html:
>>
>> - remove unnecessary line insertions
>> - cleanup leftover unused variable (build warning)
>> - patch 2/2 is unchanged (see v1)
> Err, can't find it for some reason.
sorry, it's here http://www.spinics.net/lists/linux-iio/msg23401.html
or here: pwclient get 8565821
BR,
Marc.
>
> Anyhow, applied this one to the togreg branch of iio.git - pushed
> out as testing for the autobuilders to play with it.
>
> Thanks,
>
> Jonathan
>> ---
>> drivers/iio/adc/ina2xx-adc.c | 39 ++++++++++++++++++++++++---------------
>> 1 file changed, 24 insertions(+), 15 deletions(-)
>>
>> diff --git a/drivers/iio/adc/ina2xx-adc.c b/drivers/iio/adc/ina2xx-adc.c
>> index 65909d5..4e56fe3 100644
>> --- a/drivers/iio/adc/ina2xx-adc.c
>> +++ b/drivers/iio/adc/ina2xx-adc.c
>> @@ -350,6 +350,23 @@ static ssize_t ina2xx_allow_async_readout_store(struct device *dev,
>> return len;
>> }
>>
>> +/*
>> + * Set current LSB to 1mA, shunt is in uOhms
>> + * (equation 13 in datasheet). We hardcode a Current_LSB
>> + * of 1.0 x10-6. The only remaining parameter is RShunt.
>> + * There is no need to expose the CALIBRATION register
>> + * to the user for now. But we need to reset this register
>> + * if the user updates RShunt after driver init, e.g upon
>> + * reading an EEPROM/Probe-type value.
>> + */
>> +static int ina2xx_set_calibration(struct ina2xx_chip_info *chip)
>> +{
>> + u16 regval = DIV_ROUND_CLOSEST(chip->config->calibration_factor,
>> + chip->shunt_resistor);
>> +
>> + return regmap_write(chip->regmap, INA2XX_CALIBRATION, regval);
>> +}
>> +
>> static int set_shunt_resistor(struct ina2xx_chip_info *chip, unsigned int val)
>> {
>> if (val <= 0 || val > chip->config->calibration_factor)
>> @@ -385,6 +402,11 @@ static ssize_t ina2xx_shunt_resistor_store(struct device *dev,
>> if (ret)
>> return ret;
>>
>> + /* Update the Calibration register */
>> + ret = ina2xx_set_calibration(chip);
>> + if (ret)
>> + return ret;
>> +
>> return len;
>> }
>>
>> @@ -602,24 +624,11 @@ static const struct iio_info ina2xx_info = {
>> /* Initialize the configuration and calibration registers. */
>> static int ina2xx_init(struct ina2xx_chip_info *chip, unsigned int config)
>> {
>> - u16 regval;
>> - int ret;
>> -
>> - ret = regmap_write(chip->regmap, INA2XX_CONFIG, config);
>> + int ret = regmap_write(chip->regmap, INA2XX_CONFIG, config);
>> if (ret)
>> return ret;
>>
>> - /*
>> - * Set current LSB to 1mA, shunt is in uOhms
>> - * (equation 13 in datasheet). We hardcode a Current_LSB
>> - * of 1.0 x10-6. The only remaining parameter is RShunt.
>> - * There is no need to expose the CALIBRATION register
>> - * to the user for now.
>> - */
>> - regval = DIV_ROUND_CLOSEST(chip->config->calibration_factor,
>> - chip->shunt_resistor);
>> -
>> - return regmap_write(chip->regmap, INA2XX_CALIBRATION, regval);
>> + return ina2xx_set_calibration(chip);
>> }
>>
>> static int ina2xx_probe(struct i2c_client *client,
>>
>
On 21/03/16 16:35, Marc Titinger wrote:
>
>
> On 20/03/2016 12:24, Jonathan Cameron wrote:
>> On 14/03/16 10:20, Marc Titinger wrote:
>>> The user (or an init script) may setup RShunt via sysfs after the
>>> driver was initialized, for instance based on the EEPROM contents
>>> of a modular probe. The calibration register must be set accordingly.
>>>
>>> Signed-off-by: Marc Titinger <[email protected]>
>>> ---
>>> v2 of http://www.spinics.net/lists/linux-iio/msg23402.html:
>>>
>>> - remove unnecessary line insertions
>>> - cleanup leftover unused variable (build warning)
>>> - patch 2/2 is unchanged (see v1)
>> Err, can't find it for some reason.
>
> sorry, it's here http://www.spinics.net/lists/linux-iio/msg23401.html
> or here: pwclient get 8565821
Meh, thunderbird was hiding it in completely the wrong thread.
Really should see about changing my email client one of these days.
Anyhow, applied that one now to the togreg branch of iio.git - pushed out
as testing.
thanks,
Jonathan
>
> BR,
> Marc.
>
>>
>> Anyhow, applied this one to the togreg branch of iio.git - pushed
>> out as testing for the autobuilders to play with it.
>>
>> Thanks,
>>
>> Jonathan
>>> ---
>>> drivers/iio/adc/ina2xx-adc.c | 39 ++++++++++++++++++++++++---------------
>>> 1 file changed, 24 insertions(+), 15 deletions(-)
>>>
>>> diff --git a/drivers/iio/adc/ina2xx-adc.c b/drivers/iio/adc/ina2xx-adc.c
>>> index 65909d5..4e56fe3 100644
>>> --- a/drivers/iio/adc/ina2xx-adc.c
>>> +++ b/drivers/iio/adc/ina2xx-adc.c
>>> @@ -350,6 +350,23 @@ static ssize_t ina2xx_allow_async_readout_store(struct device *dev,
>>> return len;
>>> }
>>>
>>> +/*
>>> + * Set current LSB to 1mA, shunt is in uOhms
>>> + * (equation 13 in datasheet). We hardcode a Current_LSB
>>> + * of 1.0 x10-6. The only remaining parameter is RShunt.
>>> + * There is no need to expose the CALIBRATION register
>>> + * to the user for now. But we need to reset this register
>>> + * if the user updates RShunt after driver init, e.g upon
>>> + * reading an EEPROM/Probe-type value.
>>> + */
>>> +static int ina2xx_set_calibration(struct ina2xx_chip_info *chip)
>>> +{
>>> + u16 regval = DIV_ROUND_CLOSEST(chip->config->calibration_factor,
>>> + chip->shunt_resistor);
>>> +
>>> + return regmap_write(chip->regmap, INA2XX_CALIBRATION, regval);
>>> +}
>>> +
>>> static int set_shunt_resistor(struct ina2xx_chip_info *chip, unsigned int val)
>>> {
>>> if (val <= 0 || val > chip->config->calibration_factor)
>>> @@ -385,6 +402,11 @@ static ssize_t ina2xx_shunt_resistor_store(struct device *dev,
>>> if (ret)
>>> return ret;
>>>
>>> + /* Update the Calibration register */
>>> + ret = ina2xx_set_calibration(chip);
>>> + if (ret)
>>> + return ret;
>>> +
>>> return len;
>>> }
>>>
>>> @@ -602,24 +624,11 @@ static const struct iio_info ina2xx_info = {
>>> /* Initialize the configuration and calibration registers. */
>>> static int ina2xx_init(struct ina2xx_chip_info *chip, unsigned int config)
>>> {
>>> - u16 regval;
>>> - int ret;
>>> -
>>> - ret = regmap_write(chip->regmap, INA2XX_CONFIG, config);
>>> + int ret = regmap_write(chip->regmap, INA2XX_CONFIG, config);
>>> if (ret)
>>> return ret;
>>>
>>> - /*
>>> - * Set current LSB to 1mA, shunt is in uOhms
>>> - * (equation 13 in datasheet). We hardcode a Current_LSB
>>> - * of 1.0 x10-6. The only remaining parameter is RShunt.
>>> - * There is no need to expose the CALIBRATION register
>>> - * to the user for now.
>>> - */
>>> - regval = DIV_ROUND_CLOSEST(chip->config->calibration_factor,
>>> - chip->shunt_resistor);
>>> -
>>> - return regmap_write(chip->regmap, INA2XX_CALIBRATION, regval);
>>> + return ina2xx_set_calibration(chip);
>>> }
>>>
>>> static int ina2xx_probe(struct i2c_client *client,
>>>
>>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-iio" in
> the body of a message to [email protected]
> More majordomo info at http://vger.kernel.org/majordomo-info.html