There is now support for the multiport USB controller this uses so
enable it.
The board only has a single port hooked up (despite it being wired up to
the multiport IP on the SoC). There's also a USB 2.0 mux hooked up,
which by default on boot is selected to mux properly. Grab the gpio
controlling that and ensure it stays in the right position so USB 2.0
continues to be routed from the external port to the SoC.
Signed-off-by: Andrew Halaney <[email protected]>
[Krishna: Rebased on top of usb-next]
Signed-off-by: Krishna Kurapati <[email protected]>
---
arch/arm64/boot/dts/qcom/sa8540p-ride.dts | 22 ++++++++++++++++++++++
1 file changed, 22 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
index 24fa449d48a6..53d47593306e 100644
--- a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
+++ b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
@@ -309,6 +309,19 @@ &usb_2_qmpphy0 {
status = "okay";
};
+&usb_2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb2_en_state>;
+
+ status = "okay";
+};
+
+&usb_2_dwc3 {
+ dr_mode = "host";
+ phy-names = "usb2-port0", "usb3-port0";
+ phys = <&usb_2_hsphy0>, <&usb_2_qmpphy0>;
+};
+
&xo_board_clk {
clock-frequency = <38400000>;
};
@@ -401,4 +414,13 @@ wake-pins {
bias-pull-up;
};
};
+
+ usb2_en_state: usb2-en-state {
+ /* TS3USB221A USB2.0 mux select */
+ pins = "gpio24";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ output-low;
+ };
};
--
2.40.0
On 21.06.2023 06:36, Krishna Kurapati wrote:
> There is now support for the multiport USB controller this uses so
> enable it.
>
> The board only has a single port hooked up (despite it being wired up to
> the multiport IP on the SoC). There's also a USB 2.0 mux hooked up,
> which by default on boot is selected to mux properly. Grab the gpio
> controlling that and ensure it stays in the right position so USB 2.0
> continues to be routed from the external port to the SoC.
>
> Signed-off-by: Andrew Halaney <[email protected]>
> [Krishna: Rebased on top of usb-next]
If that's your only change to this patch, you should have kept the
Author: field unchanged.
> Signed-off-by: Krishna Kurapati <[email protected]>
> ---
Same comments as patch 9
Konrad
> arch/arm64/boot/dts/qcom/sa8540p-ride.dts | 22 ++++++++++++++++++++++
> 1 file changed, 22 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
> index 24fa449d48a6..53d47593306e 100644
> --- a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
> +++ b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
> @@ -309,6 +309,19 @@ &usb_2_qmpphy0 {
> status = "okay";
> };
>
> +&usb_2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&usb2_en_state>;
> +
> + status = "okay";
> +};
> +
> +&usb_2_dwc3 {
> + dr_mode = "host";
> + phy-names = "usb2-port0", "usb3-port0";
> + phys = <&usb_2_hsphy0>, <&usb_2_qmpphy0>;
> +};
> +
> &xo_board_clk {
> clock-frequency = <38400000>;
> };
> @@ -401,4 +414,13 @@ wake-pins {
> bias-pull-up;
> };
> };
> +
> + usb2_en_state: usb2-en-state {
> + /* TS3USB221A USB2.0 mux select */
> + pins = "gpio24";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-disable;
> + output-low;
> + };
> };
On 6/24/2023 4:12 AM, Konrad Dybcio wrote:
> On 21.06.2023 06:36, Krishna Kurapati wrote:
>> There is now support for the multiport USB controller this uses so
>> enable it.
>>
>> The board only has a single port hooked up (despite it being wired up to
>> the multiport IP on the SoC). There's also a USB 2.0 mux hooked up,
>> which by default on boot is selected to mux properly. Grab the gpio
>> controlling that and ensure it stays in the right position so USB 2.0
>> continues to be routed from the external port to the SoC.
>>
>> Signed-off-by: Andrew Halaney <[email protected]>
>> [Krishna: Rebased on top of usb-next]
> If that's your only change to this patch, you should have kept the
> Author: field unchanged.
>
Sure, will do reset-author and resubmit the patch next version.
>> Signed-off-by: Krishna Kurapati <[email protected]>
>> ---
> Same comments as patch 9
>
> Konrad
Thanks for the review.
Regards,
Krishna,
>> arch/arm64/boot/dts/qcom/sa8540p-ride.dts | 22 ++++++++++++++++++++++
>> 1 file changed, 22 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
>> index 24fa449d48a6..53d47593306e 100644
>> --- a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
>> +++ b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
>> @@ -309,6 +309,19 @@ &usb_2_qmpphy0 {
>> status = "okay";
>> };
>>
>> +&usb_2 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&usb2_en_state>;
>> +
>> + status = "okay";
>> +};
>> +
>> +&usb_2_dwc3 {
>> + dr_mode = "host";
>> + phy-names = "usb2-port0", "usb3-port0";
>> + phys = <&usb_2_hsphy0>, <&usb_2_qmpphy0>;
>> +};
>> +
>> &xo_board_clk {
>> clock-frequency = <38400000>;
>> };
>> @@ -401,4 +414,13 @@ wake-pins {
>> bias-pull-up;
>> };
>> };
>> +
>> + usb2_en_state: usb2-en-state {
>> + /* TS3USB221A USB2.0 mux select */
>> + pins = "gpio24";
>> + function = "gpio";
>> + drive-strength = <2>;
>> + bias-disable;
>> + output-low;
>> + };
>> };