From: Eli Billauer <[email protected]>
The XillyUSB driver is the USB variant for the Xillybus FPGA IP core.
Even though it presents a nearly identical API on the FPGA and host,
it's almost a complete rewrite of the driver: The framework for exchanging
data on a USB bus is fundamentally different from doing the same with a
PCIe interface, which leaves very little in common between the existing
driver and the new one for XillyUSB.
Signed-off-by: Eli Billauer <[email protected]>
---
Notes:
Changelog:
v2:
- Add comment in Kconfig file, saying XILLYUSB really doesn't depend
on XILLYBUS (following comment by Randy Dunlap)
- Use SEEK_* predefined constants instead of numbers
drivers/char/xillybus/Kconfig | 13 +
drivers/char/xillybus/Makefile | 1 +
drivers/char/xillybus/xillyusb.c | 2363 ++++++++++++++++++++++++++++++
3 files changed, 2377 insertions(+)
create mode 100644 drivers/char/xillybus/xillyusb.c
diff --git a/drivers/char/xillybus/Kconfig b/drivers/char/xillybus/Kconfig
index 130dbdce858f..2b5192fd22b9 100644
--- a/drivers/char/xillybus/Kconfig
+++ b/drivers/char/xillybus/Kconfig
@@ -32,3 +32,16 @@ config XILLYBUS_OF
system, say M.
endif # if XILLYBUS
+
+# XILLYUSB doesn't depend on XILLYBUS
+
+config XILLYUSB
+ tristate "XillyUSB: Xillybus generic FPGA interface for USB"
+ depends on USB
+ select CRC32
+ help
+ XillyUSB is the Xillybus variant which uses USB for communicating
+ with the FPGA.
+
+ Set to M if you want Xillybus to use USB for communicating with
+ the FPGA.
diff --git a/drivers/char/xillybus/Makefile b/drivers/char/xillybus/Makefile
index 099e9a3585fc..57471fb61a12 100644
--- a/drivers/char/xillybus/Makefile
+++ b/drivers/char/xillybus/Makefile
@@ -6,3 +6,4 @@
obj-$(CONFIG_XILLYBUS) += xillybus_core.o
obj-$(CONFIG_XILLYBUS_PCIE) += xillybus_pcie.o
obj-$(CONFIG_XILLYBUS_OF) += xillybus_of.o
+obj-$(CONFIG_XILLYUSB) += xillyusb.o
diff --git a/drivers/char/xillybus/xillyusb.c b/drivers/char/xillybus/xillyusb.c
new file mode 100644
index 000000000000..492f4ee39e78
--- /dev/null
+++ b/drivers/char/xillybus/xillyusb.c
@@ -0,0 +1,2363 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2020 Xillybus Ltd, http://xillybus.com
+ *
+ * Driver for the XillyUSB FPGA/host framework.
+ *
+ * This driver interfaces with a special IP core in an FPGA, setting up
+ * a pipe between a hardware FIFO in the programmable logic and a device
+ * file in the host. The number of such pipes and their attributes are
+ * set up on the logic. This driver detects these automatically and
+ * creates the device files accordingly.
+ */
+
+#include <linux/types.h>
+#include <linux/slab.h>
+#include <linux/list.h>
+#include <linux/device.h>
+#include <linux/module.h>
+#include <asm/byteorder.h>
+#include <linux/io.h>
+#include <linux/interrupt.h>
+#include <linux/sched.h>
+#include <linux/fs.h>
+#include <linux/cdev.h>
+#include <linux/spinlock.h>
+#include <linux/mutex.h>
+#include <linux/atomic.h>
+#include <linux/workqueue.h>
+#include <linux/crc32.h>
+#include <linux/poll.h>
+#include <linux/delay.h>
+#include <linux/usb.h>
+
+MODULE_DESCRIPTION("Driver for XillyUSB FPGA IP Core");
+MODULE_AUTHOR("Eli Billauer, Xillybus Ltd.");
+MODULE_VERSION("1.0");
+MODULE_ALIAS("xillyusb");
+MODULE_LICENSE("GPL v2");
+
+#define XILLY_RX_TIMEOUT (10 * HZ / 1000)
+#define XILLY_RESPONSE_TIMEOUT (500 * HZ / 1000)
+
+#define MAX_XILLYUSB_DEVS 64
+#define BUF_SIZE_ORDER 4
+#define BUFNUM 8
+#define LOG2_IDT_FIFO_SIZE 16
+#define LOG2_INITIAL_FIFO_BUF_SIZE 16
+
+#define MSG_EP_NUM 1
+#define IN_EP_NUM 1
+
+static const char xillyname[] = "xillyusb";
+/* err_name is used in log messages, where dev_err() might fail */
+static const char *err_name = xillyname;
+
+static struct class *xillyusb_class;
+
+static char xdev_map[MAX_XILLYUSB_DEVS];
+/* xdev_mutex is spinlock style: Taken last and for quick operations. */
+static DEFINE_MUTEX(xdev_mutex);
+static LIST_HEAD(xdev_list);
+
+static unsigned int fifo_buf_order;
+
+#define USB_VENDOR_ID_XILINX 0x03fd
+#define USB_VENDOR_ID_ALTERA 0x09fb
+
+#define USB_PRODUCT_ID_XILLYUSB 0xebbe
+
+static const struct usb_device_id xillyusb_table[] = {
+ { USB_DEVICE(USB_VENDOR_ID_XILINX, USB_PRODUCT_ID_XILLYUSB) },
+ { USB_DEVICE(USB_VENDOR_ID_ALTERA, USB_PRODUCT_ID_XILLYUSB) },
+ { }
+};
+
+MODULE_DEVICE_TABLE(usb, xillyusb_table);
+
+struct xillyusb_dev;
+
+struct xillyfifo {
+ unsigned int bufsize; /* In bytes, always a power of 2 */
+ unsigned int bufnum;
+ unsigned int size; /* Lazy: Equals bufsize * bufnum */
+ unsigned int buf_order;
+ atomic_t fill; /* Number of bytes in the FIFO */
+ wait_queue_head_t waitq;
+ unsigned int readpos;
+ unsigned int readbuf;
+ unsigned int writepos;
+ unsigned int writebuf;
+ void **mem;
+};
+
+struct xillyusb_channel;
+
+struct xillyusb_endpoint {
+ struct xillyusb_dev *xdev;
+
+ struct list_head buffers;
+ struct list_head filled_buffers;
+ spinlock_t buffers_lock; /* protect these two lists */
+
+ unsigned int order;
+ unsigned int buffer_size;
+
+ unsigned int fill_mask;
+
+ int outstanding_urbs;
+
+ struct usb_anchor anchor;
+
+ struct xillyfifo fifo;
+
+ struct work_struct workitem;
+ bool shutting_down;
+
+ u8 ep_num;
+};
+
+struct xillyusb_channel {
+ struct xillyusb_dev *xdev;
+
+ struct xillyfifo *in_fifo;
+ struct xillyusb_endpoint *out_ep;
+ struct mutex lock; /* protect @out_ep and @in_fifo */
+
+ struct mutex in_mutex; /* serialize fops on FPGA to host stream */
+ struct mutex out_mutex; /* serialize fops on host to FPGA stream */
+ wait_queue_head_t flushq;
+
+ int chan_idx;
+
+ u32 in_consumed_bytes;
+ u32 in_current_checkpoint;
+ u32 out_bytes;
+
+ unsigned int in_log2_element_size;
+ unsigned int out_log2_element_size;
+ unsigned int in_log2_fifo_size;
+ unsigned int out_log2_fifo_size;
+
+ unsigned int read_data_ok; /* EOF not arrived (yet) */
+ unsigned int poll_used;
+ unsigned int flushing;
+ unsigned int flushed;
+ unsigned int canceled;
+
+ /* Bit fields protected by xdev_mutex except for initialization */
+ unsigned readable:1;
+ unsigned writable:1;
+ unsigned open_for_read:1;
+ unsigned open_for_write:1;
+ unsigned in_synchronous:1;
+ unsigned out_synchronous:1;
+ unsigned in_seekable:1;
+ unsigned out_seekable:1;
+};
+
+struct xillybuffer {
+ struct list_head entry;
+ struct xillyusb_endpoint *ep;
+ void *buf;
+ unsigned int len;
+};
+
+struct xillyusb_dev {
+ struct xillyusb_channel *channels;
+
+ struct usb_device *udev;
+ struct usb_interface *interface;
+ struct kref kref;
+ struct mutex io_mutex; /* synchronize I/O with disconnect */
+ struct list_head list_entry;
+ struct workqueue_struct *workq;
+
+ int error;
+ spinlock_t error_lock; /* protect @error */
+ struct work_struct wakeup_workitem;
+
+ int index;
+ struct cdev *cdev;
+ int major;
+ int lowest_minor;
+ int num_channels;
+
+ struct xillyusb_endpoint *msg_ep;
+ struct xillyusb_endpoint *in_ep;
+
+ struct mutex msg_mutex; /* serialize opcode transmission */
+ int in_bytes_left;
+ int leftover_chan_num;
+ unsigned int in_counter;
+ struct mutex process_in_mutex; /* synchronize wakeup_all() */
+};
+
+/* FPGA to host opcodes */
+enum {
+ OPCODE_DATA = 0,
+ OPCODE_QUIESCE_ACK = 1,
+ OPCODE_EOF = 2,
+ OPCODE_REACHED_CHECKPOINT = 3,
+ OPCODE_CANCELED_CHECKPOINT = 4,
+};
+
+/* Host to FPGA opcodes */
+enum {
+ OPCODE_QUIESCE = 0,
+ OPCODE_REQ_IDT = 1,
+ OPCODE_SET_CHECKPOINT = 2,
+ OPCODE_CLOSE = 3,
+ OPCODE_SET_PUSH = 4,
+ OPCODE_UPDATE_PUSH = 5,
+ OPCODE_CANCEL_CHECKPOINT = 6,
+ OPCODE_SET_ADDR = 7,
+};
+
+/*
+ * fifo_write() and fifo_read() are NOT reentrant (i.e. concurrent multiple
+ * calls to each on the same FIFO is not allowed) however it's OK to have
+ * threads calling each of the two functions once on the same FIFO, and
+ * at the same time.
+ */
+
+static int fifo_write(struct xillyfifo *fifo,
+ const void *data, unsigned int len,
+ int (*copier)(void *, const void *, int))
+{
+ unsigned int done = 0;
+ unsigned int todo = len;
+ unsigned int nmax;
+ unsigned int writepos = fifo->writepos;
+ unsigned int writebuf = fifo->writebuf;
+
+ nmax = fifo->size - atomic_read(&fifo->fill);
+
+ while (1) {
+ unsigned int nrail = fifo->bufsize - writepos;
+ unsigned int n = min(todo, nmax);
+
+ if (n == 0) {
+ /*
+ * Ensure copied data is visible before
+ * it's accounted for.
+ */
+ smp_wmb();
+ atomic_add(done, &fifo->fill);
+
+ fifo->writepos = writepos;
+ fifo->writebuf = writebuf;
+
+ return done;
+ }
+
+ if (n > nrail)
+ n = nrail;
+
+ if ((*copier)(fifo->mem[writebuf] + writepos, data + done, n))
+ return -EFAULT;
+
+ done += n;
+ todo -= n;
+
+ writepos += n;
+ nmax -= n;
+
+ if (writepos == fifo->bufsize) {
+ writepos = 0;
+ writebuf++;
+
+ if (writebuf == fifo->bufnum)
+ writebuf = 0;
+ }
+ }
+}
+
+static unsigned int fifo_read(struct xillyfifo *fifo,
+ void *data, unsigned int len,
+ int (*copier)(void *, const void *, int))
+{
+ unsigned int done = 0;
+ unsigned int todo = len;
+ unsigned int fill;
+ unsigned int readpos = fifo->readpos;
+ unsigned int readbuf = fifo->readbuf;
+
+ fill = atomic_read(&fifo->fill);
+
+ /* Ensure that the data accounted for is synchronized in buffer */
+ smp_rmb();
+
+ while (1) {
+ unsigned int nrail = fifo->bufsize - readpos;
+ unsigned int n = min(todo, fill);
+
+ if (n == 0) {
+ atomic_sub(done, &fifo->fill);
+
+ fifo->readpos = readpos;
+ fifo->readbuf = readbuf;
+
+ return done;
+ }
+
+ if (n > nrail)
+ n = nrail;
+
+ if ((*copier)(data + done, fifo->mem[readbuf] + readpos, n))
+ return -EFAULT;
+
+ done += n;
+ todo -= n;
+
+ readpos += n;
+ fill -= n;
+
+ if (readpos == fifo->bufsize) {
+ readpos = 0;
+ readbuf++;
+
+ if (readbuf == fifo->bufnum)
+ readbuf = 0;
+ }
+ }
+}
+
+static int fifo_init(struct xillyfifo *fifo,
+ unsigned int log2_size)
+{
+ unsigned int log2_bufnum;
+ unsigned int buf_order;
+ int i;
+
+ unsigned int log2_fifo_buf_size;
+
+retry:
+ log2_fifo_buf_size = fifo_buf_order + PAGE_SHIFT;
+
+ if (log2_size > log2_fifo_buf_size) {
+ log2_bufnum = log2_size - log2_fifo_buf_size;
+ buf_order = fifo_buf_order;
+ fifo->bufsize = 1 << log2_fifo_buf_size;
+ } else {
+ log2_bufnum = 0;
+ buf_order = (log2_size > PAGE_SHIFT) ?
+ log2_size - PAGE_SHIFT : 0;
+ fifo->bufsize = 1 << log2_size;
+ }
+
+ fifo->bufnum = 1 << log2_bufnum;
+ fifo->size = fifo->bufnum * fifo->bufsize;
+ fifo->buf_order = buf_order;
+
+ fifo->mem = kmalloc_array(fifo->bufnum, sizeof(void *), GFP_KERNEL);
+
+ if (!fifo->mem)
+ return -ENOMEM;
+
+ for (i = 0; i < fifo->bufnum; i++) {
+ fifo->mem[i] = (void *)
+ __get_free_pages(GFP_KERNEL, buf_order);
+
+ if (!fifo->mem[i])
+ goto memfail;
+ }
+
+ atomic_set(&fifo->fill, 0);
+ fifo->readpos = 0;
+ fifo->readbuf = 0;
+ fifo->writepos = 0;
+ fifo->writebuf = 0;
+ init_waitqueue_head(&fifo->waitq);
+ return 0;
+
+memfail:
+ for (i--; i >= 0; i--)
+ free_pages((unsigned long)fifo->mem[i], buf_order);
+
+ kfree(fifo->mem);
+ fifo->mem = NULL;
+
+ if (fifo_buf_order) {
+ fifo_buf_order--;
+ pr_warn("%s: Trying again to allocate FIFO %d bytes, now with segments of %d bytes each\n",
+ err_name, 1 << log2_size,
+ 1 << (fifo_buf_order + PAGE_SHIFT));
+ goto retry;
+ } else {
+ pr_err("%s: Failed to allocate FIFO with %d bytes, despite attepts to chop it into small pieces.\n",
+ err_name, 1 << log2_size);
+ return -ENOMEM;
+ }
+}
+
+static void fifo_mem_release(struct xillyfifo *fifo)
+{
+ int i;
+
+ if (!fifo->mem)
+ return;
+
+ for (i = 0; i < fifo->bufnum; i++)
+ free_pages((unsigned long)fifo->mem[i], fifo->buf_order);
+
+ kfree(fifo->mem);
+}
+
+/*
+ * Note that endpoint_dealloc() also frees fifo memory (if allocated), even
+ * though endpoint_alloc doesn't allocate that memory.
+ */
+
+static void endpoint_dealloc(struct xillyusb_endpoint *ep)
+{
+ struct list_head *this, *next;
+ struct list_head *buffers = &ep->buffers;
+ unsigned int order = ep->order;
+
+ ep->shutting_down = true;
+
+ /*
+ * The first cancel_work_sync() doesn't just cancel a possibly running
+ * work item, but also ensures that if it's re-queued by a URB
+ * completer in a race condition, the next execution of the work item
+ * will see the ep->shutting_down as true, and do nothing. Hence we're
+ * sure all queued URBs are anchored and no new ones will be added
+ * after cancel_work_sync() returns.
+ * However a second cancel_work_sync() is still required if such race
+ * condition would re-queue the work item, since @ep is just about to
+ * be freed.
+ */
+
+ cancel_work_sync(&ep->workitem);
+ usb_kill_anchored_urbs(&ep->anchor);
+ cancel_work_sync(&ep->workitem);
+
+ fifo_mem_release(&ep->fifo);
+
+ list_for_each_safe(this, next, buffers) {
+ struct xillybuffer *xb =
+ list_entry(this, struct xillybuffer, entry);
+
+ free_pages((unsigned long)xb->buf, order);
+ kfree(xb);
+ }
+
+ kfree(ep);
+}
+
+static struct xillyusb_endpoint
+*endpoint_alloc(struct xillyusb_dev *xdev,
+ u8 ep_num,
+ void (*work)(struct work_struct *),
+ unsigned int order,
+ int bufnum)
+{
+ int i;
+
+ struct xillyusb_endpoint *ep;
+
+ ep = kzalloc(sizeof(*ep), GFP_KERNEL);
+
+ if (!ep)
+ return NULL;
+
+ INIT_LIST_HEAD(&ep->buffers);
+ INIT_LIST_HEAD(&ep->filled_buffers);
+
+ spin_lock_init(&ep->buffers_lock);
+
+ init_usb_anchor(&ep->anchor);
+ INIT_WORK(&ep->workitem, work);
+
+ ep->order = order;
+ ep->buffer_size = 1 << (PAGE_SHIFT + order);
+ ep->outstanding_urbs = 0;
+ ep->xdev = xdev;
+ ep->ep_num = ep_num;
+ ep->shutting_down = false;
+
+ for (i = 0; i < bufnum; i++) {
+ struct xillybuffer *xb;
+ unsigned long addr;
+
+ xb = kzalloc(sizeof(*xb), GFP_KERNEL);
+
+ if (!xb) {
+ endpoint_dealloc(ep);
+ return NULL;
+ }
+
+ addr = __get_free_pages(GFP_KERNEL, order);
+
+ if (!addr) {
+ kfree(xb);
+ endpoint_dealloc(ep);
+ return NULL;
+ }
+
+ xb->buf = (void *)addr;
+ xb->ep = ep;
+ list_add_tail(&xb->entry, &ep->buffers);
+ }
+ return ep;
+}
+
+static void cleanup_dev(struct kref *kref)
+{
+ struct xillyusb_dev *xdev =
+ container_of(kref, struct xillyusb_dev, kref);
+
+ if (xdev->in_ep)
+ endpoint_dealloc(xdev->in_ep);
+
+ if (xdev->msg_ep)
+ endpoint_dealloc(xdev->msg_ep);
+
+ if (xdev->workq)
+ destroy_workqueue(xdev->workq);
+
+ kfree(xdev->channels); /* Argument may be NULL, and that's fine */
+ kfree(xdev);
+}
+
+/*
+ * wakeup_all() is implemented as a work item, because of the need to be
+ * sure that bulk_in_work() sees xdev->error with a non-zero value if it
+ * runs after all read_data_ok have been cleared. xdev->error is assigned
+ * with this non-zero number prior to queueing the work, but it seems like
+ * only a mutex ensures this correct order of execution.
+ *
+ * In particular, the fact that wakeup_all() and bulk_in_work() are queued on
+ * the same workqueue makes their concurrent execution very unlikely,
+ * however the kernel's API doesn't seem to ensure this strictly.
+ * report_io_error() is possibly called in atomic context and can therefore
+ * not take a mutex.
+ */
+
+static void wakeup_all(struct work_struct *work)
+{
+ int i;
+ struct xillyusb_dev *xdev = container_of(work, struct xillyusb_dev,
+ wakeup_workitem);
+
+ mutex_lock(&xdev->process_in_mutex);
+
+ for (i = 0; i < xdev->num_channels; i++) {
+ struct xillyusb_channel *chan = &xdev->channels[i];
+
+ mutex_lock(&chan->lock);
+
+ if (chan->in_fifo) {
+ /*
+ * Fake an EOF: Even if such arrives, it won't be
+ * processed.
+ */
+ chan->read_data_ok = 0;
+ wake_up_interruptible(&chan->in_fifo->waitq);
+ }
+
+ if (chan->out_ep)
+ wake_up_interruptible(&chan->out_ep->fifo.waitq);
+
+ mutex_unlock(&chan->lock);
+
+ wake_up_interruptible(&chan->flushq);
+ }
+
+ mutex_unlock(&xdev->process_in_mutex);
+
+ wake_up_interruptible(&xdev->msg_ep->fifo.waitq);
+
+ kref_put(&xdev->kref, cleanup_dev);
+}
+
+static void report_io_error(struct xillyusb_dev *xdev,
+ int errcode)
+{
+ unsigned long flags;
+ bool do_once = false;
+
+ spin_lock_irqsave(&xdev->error_lock, flags);
+ if (!xdev->error) {
+ xdev->error = errcode;
+ do_once = true;
+ }
+ spin_unlock_irqrestore(&xdev->error_lock, flags);
+
+ if (do_once) {
+ kref_get(&xdev->kref); /* xdev is used by work item */
+ queue_work(xdev->workq, &xdev->wakeup_workitem);
+ }
+}
+
+/*
+ * safely_assign_in_fifo() changes the value of chan->in_fifo and ensures
+ * the previous pointer is never used after its return.
+ */
+
+static void safely_assign_in_fifo(struct xillyusb_channel *chan,
+ struct xillyfifo *fifo)
+{
+ mutex_lock(&chan->lock);
+ chan->in_fifo = fifo;
+ mutex_unlock(&chan->lock);
+
+ flush_work(&chan->xdev->in_ep->workitem);
+}
+
+static int xilly_memcpy(void *dst, const void *src, int n)
+{
+ memcpy(dst, src, n);
+ return 0;
+}
+
+static void bulk_in_completer(struct urb *urb)
+{
+ struct xillybuffer *xb = urb->context;
+ struct xillyusb_endpoint *ep = xb->ep;
+ unsigned long flags;
+
+ if (urb->status) {
+ if (!(urb->status == -ENOENT ||
+ urb->status == -ECONNRESET ||
+ urb->status == -ESHUTDOWN))
+ report_io_error(ep->xdev, -EIO);
+
+ spin_lock_irqsave(&ep->buffers_lock, flags);
+ list_add_tail(&xb->entry, &ep->buffers);
+ ep->outstanding_urbs--;
+ spin_unlock_irqrestore(&ep->buffers_lock, flags);
+
+ return;
+ }
+
+ xb->len = urb->actual_length;
+
+ spin_lock_irqsave(&ep->buffers_lock, flags);
+ list_add_tail(&xb->entry, &ep->filled_buffers);
+ spin_unlock_irqrestore(&ep->buffers_lock, flags);
+
+ if (!ep->shutting_down)
+ queue_work(ep->xdev->workq, &ep->workitem);
+}
+
+static void bulk_out_completer(struct urb *urb)
+{
+ struct xillybuffer *xb = urb->context;
+ struct xillyusb_endpoint *ep = xb->ep;
+ unsigned long flags;
+
+ if (urb->status &&
+ (!(urb->status == -ENOENT ||
+ urb->status == -ECONNRESET ||
+ urb->status == -ESHUTDOWN)))
+ report_io_error(ep->xdev, -EIO);
+
+ spin_lock_irqsave(&ep->buffers_lock, flags);
+ list_add_tail(&xb->entry, &ep->buffers);
+ ep->outstanding_urbs--;
+ spin_unlock_irqrestore(&ep->buffers_lock, flags);
+
+ if (!ep->shutting_down)
+ queue_work(ep->xdev->workq, &ep->workitem);
+}
+
+static void try_queue_bulk_in(struct xillyusb_endpoint *ep)
+{
+ struct xillyusb_dev *xdev = ep->xdev;
+ struct xillybuffer *xb;
+ struct urb *urb;
+
+ int rc;
+ unsigned long flags;
+ unsigned int bufsize = ep->buffer_size;
+
+ if (ep->shutting_down)
+ return;
+
+ mutex_lock(&xdev->io_mutex);
+
+ if (!xdev->interface || xdev->error)
+ goto done;
+
+ while (1) {
+ spin_lock_irqsave(&ep->buffers_lock, flags);
+
+ if (list_empty(&ep->buffers)) {
+ spin_unlock_irqrestore(&ep->buffers_lock, flags);
+ goto done;
+ }
+
+ xb = list_first_entry(&ep->buffers, struct xillybuffer, entry);
+ list_del(&xb->entry);
+ ep->outstanding_urbs++;
+
+ spin_unlock_irqrestore(&ep->buffers_lock, flags);
+
+ urb = usb_alloc_urb(0, GFP_KERNEL);
+ if (!urb) {
+ report_io_error(xdev, -ENOMEM);
+ goto relist;
+ }
+
+ usb_fill_bulk_urb(urb, xdev->udev,
+ usb_rcvbulkpipe(xdev->udev, ep->ep_num),
+ xb->buf, bufsize, bulk_in_completer, xb);
+
+ usb_anchor_urb(urb, &ep->anchor);
+
+ rc = usb_submit_urb(urb, GFP_KERNEL);
+
+ if (rc) {
+ report_io_error(xdev, (rc == -ENOMEM) ? -ENOMEM :
+ -EIO);
+ goto unanchor;
+ }
+
+ usb_free_urb(urb); /* This just decrements reference count */
+ }
+
+unanchor:
+ usb_unanchor_urb(urb);
+ usb_free_urb(urb);
+
+relist:
+ spin_lock_irqsave(&ep->buffers_lock, flags);
+ list_add_tail(&xb->entry, &ep->buffers);
+ ep->outstanding_urbs--;
+ spin_unlock_irqrestore(&ep->buffers_lock, flags);
+
+done:
+ mutex_unlock(&xdev->io_mutex);
+}
+
+static void try_queue_bulk_out(struct xillyusb_endpoint *ep)
+{
+ struct xillyfifo *fifo = &ep->fifo;
+ struct xillyusb_dev *xdev = ep->xdev;
+ struct xillybuffer *xb;
+ struct urb *urb;
+
+ int rc;
+ unsigned int fill;
+ unsigned long flags;
+ bool submitted = false;
+
+ if (ep->shutting_down)
+ return;
+
+ mutex_lock(&xdev->io_mutex);
+
+ if (!xdev->interface || xdev->error)
+ goto done;
+
+ fill = atomic_read(&fifo->fill) & ep->fill_mask;
+
+ while (1) {
+ int count;
+ unsigned int max_read;
+
+ if (fill == 0)
+ goto done;
+
+ spin_lock_irqsave(&ep->buffers_lock, flags);
+
+ if ((fill < ep->buffer_size && ep->outstanding_urbs) ||
+ list_empty(&ep->buffers)) {
+ spin_unlock_irqrestore(&ep->buffers_lock, flags);
+ goto done;
+ }
+
+ xb = list_first_entry(&ep->buffers, struct xillybuffer, entry);
+ list_del(&xb->entry);
+ ep->outstanding_urbs++;
+
+ spin_unlock_irqrestore(&ep->buffers_lock, flags);
+
+ max_read = min(fill, ep->buffer_size);
+
+ count = fifo_read(&ep->fifo, xb->buf, max_read, xilly_memcpy);
+
+ /*
+ * xilly_memcpy always returns 0 => fifo_read can't fail =>
+ * count > 0
+ */
+
+ urb = usb_alloc_urb(0, GFP_KERNEL);
+ if (!urb) {
+ report_io_error(xdev, -ENOMEM);
+ goto relist;
+ }
+
+ usb_fill_bulk_urb(urb, xdev->udev,
+ usb_sndbulkpipe(xdev->udev, ep->ep_num),
+ xb->buf, count, bulk_out_completer, xb);
+
+ usb_anchor_urb(urb, &ep->anchor);
+
+ rc = usb_submit_urb(urb, GFP_KERNEL);
+
+ if (rc) {
+ report_io_error(xdev, (rc == -ENOMEM) ? -ENOMEM :
+ -EIO);
+ goto unanchor;
+ }
+
+ usb_free_urb(urb); /* This just decrements reference count */
+
+ fill -= count;
+ submitted = true;
+ }
+
+unanchor:
+ usb_unanchor_urb(urb);
+ usb_free_urb(urb);
+
+relist:
+ spin_lock_irqsave(&ep->buffers_lock, flags);
+ list_add_tail(&xb->entry, &ep->buffers);
+ ep->outstanding_urbs--;
+ spin_unlock_irqrestore(&ep->buffers_lock, flags);
+
+done:
+ mutex_unlock(&xdev->io_mutex);
+
+ if (submitted)
+ wake_up_interruptible(&fifo->waitq);
+}
+
+static void bulk_out_work(struct work_struct *work)
+{
+ struct xillyusb_endpoint *ep = container_of(work,
+ struct xillyusb_endpoint,
+ workitem);
+ try_queue_bulk_out(ep);
+}
+
+static int process_in_opcode(struct xillyusb_dev *xdev,
+ int opcode,
+ int chan_num)
+{
+ struct xillyusb_channel *chan;
+ int chan_idx = chan_num >> 1;
+
+ if (chan_idx >= xdev->num_channels) {
+ pr_err("%s: Received illegal channel ID %d from FPGA\n",
+ err_name, chan_num);
+ return -EIO;
+ }
+
+ chan = &xdev->channels[chan_idx];
+
+ switch (opcode) {
+ case OPCODE_EOF:
+ if (!READ_ONCE(chan->read_data_ok)) {
+ pr_err("%s: Received unexpected EOF for channel %d\n",
+ err_name, chan_num);
+ return -EIO;
+ }
+
+ /*
+ * A write memory barrier ensures that the FIFO's fill level
+ * is visible before read_data_ok turns zero, so the data in
+ * the FIFO isn't missed by the consumer.
+ */
+ smp_wmb();
+ WRITE_ONCE(chan->read_data_ok, 0);
+ wake_up_interruptible(&chan->in_fifo->waitq);
+ break;
+
+ case OPCODE_REACHED_CHECKPOINT:
+ chan->flushing = 0;
+ wake_up_interruptible(&chan->flushq);
+ break;
+
+ case OPCODE_CANCELED_CHECKPOINT:
+ chan->canceled = 1;
+ wake_up_interruptible(&chan->flushq);
+ break;
+
+ default:
+ pr_err("%s: Received illegal opcode %d from FPGA\n",
+ err_name, opcode);
+ return -EIO;
+ }
+
+ return 0;
+}
+
+static int process_bulk_in(struct xillybuffer *xb)
+{
+ struct xillyusb_endpoint *ep = xb->ep;
+ struct xillyusb_dev *xdev = ep->xdev;
+ int dws = xb->len >> 2;
+ __le32 *p = xb->buf;
+ u32 ctrlword;
+ struct xillyusb_channel *chan;
+ struct xillyfifo *fifo;
+ int chan_num = 0, opcode;
+ int chan_idx;
+ int bytes, count, dwconsume;
+ int in_bytes_left = 0;
+ int rc;
+
+ if ((dws << 2) != xb->len) {
+ pr_err("%s: Received BULK IN transfer with %d bytes, not a multiple of 4\n",
+ err_name, xb->len);
+ return -EIO;
+ }
+
+ if (xdev->in_bytes_left) {
+ bytes = min(xdev->in_bytes_left, dws << 2);
+ in_bytes_left = xdev->in_bytes_left - bytes;
+ chan_num = xdev->leftover_chan_num;
+ goto resume_leftovers;
+ }
+
+ while (dws) {
+ ctrlword = le32_to_cpu(*p++);
+ dws--;
+
+ chan_num = ctrlword & 0xfff;
+ count = (ctrlword >> 12) & 0x3ff;
+ opcode = (ctrlword >> 24) & 0xf;
+
+ if (opcode != OPCODE_DATA) {
+ unsigned int in_counter = xdev->in_counter++ & 0x3ff;
+
+ if (count != in_counter) {
+ pr_err("%s: Expected opcode counter %d, got %d\n",
+ err_name, in_counter, count);
+ return -EIO;
+ }
+
+ rc = process_in_opcode(xdev, opcode, chan_num);
+
+ if (rc)
+ return rc;
+
+ continue;
+ }
+
+ bytes = min(count + 1, dws << 2);
+ in_bytes_left = count + 1 - bytes;
+
+resume_leftovers:
+ chan_idx = chan_num >> 1;
+
+ if (!(chan_num & 1) || chan_idx >= xdev->num_channels ||
+ !READ_ONCE(xdev->channels[chan_idx].read_data_ok)) {
+ pr_err("%s: Received illegal channel ID %d from FPGA\n",
+ err_name, chan_num);
+ return -EIO;
+ }
+ chan = &xdev->channels[chan_idx];
+
+ fifo = chan->in_fifo;
+
+ if (unlikely(!fifo))
+ return -EIO; /* We got really unexpected data */
+
+ if (bytes != fifo_write(fifo, p, bytes, xilly_memcpy)) {
+ pr_err("%s: Misbehaving FPGA overflew an upstream FIFO!\n",
+ err_name);
+ return -EIO;
+ }
+
+ wake_up_interruptible(&fifo->waitq);
+
+ dwconsume = (bytes + 3) >> 2;
+ dws -= dwconsume;
+ p += dwconsume;
+ }
+
+ xdev->in_bytes_left = in_bytes_left;
+ xdev->leftover_chan_num = chan_num;
+ return 0;
+}
+
+static void bulk_in_work(struct work_struct *work)
+{
+ struct xillyusb_endpoint *ep =
+ container_of(work, struct xillyusb_endpoint, workitem);
+ struct xillyusb_dev *xdev = ep->xdev;
+ unsigned long flags;
+ struct xillybuffer *xb;
+ bool consumed = false;
+ int rc = 0;
+
+ mutex_lock(&xdev->process_in_mutex);
+
+ spin_lock_irqsave(&ep->buffers_lock, flags);
+
+ while (1) {
+ if (list_empty(&ep->filled_buffers)) {
+ spin_unlock_irqrestore(&ep->buffers_lock, flags);
+
+ mutex_unlock(&xdev->process_in_mutex);
+
+ if (consumed)
+ try_queue_bulk_in(ep);
+
+ return;
+ }
+
+ xb = list_first_entry(&ep->filled_buffers, struct xillybuffer,
+ entry);
+ list_del(&xb->entry);
+
+ spin_unlock_irqrestore(&ep->buffers_lock, flags);
+
+ consumed = true;
+
+ if (!xdev->error)
+ rc = process_bulk_in(xb);
+
+ if (rc) {
+ mutex_unlock(&xdev->process_in_mutex);
+ report_io_error(xdev, rc);
+ return;
+ }
+
+ spin_lock_irqsave(&ep->buffers_lock, flags);
+ list_add_tail(&xb->entry, &ep->buffers);
+ ep->outstanding_urbs--;
+ }
+}
+
+static int xillyusb_send_opcode(struct xillyusb_dev *xdev,
+ int chan_num, char opcode, u32 data)
+{
+ struct xillyusb_endpoint *ep = xdev->msg_ep;
+ struct xillyfifo *fifo = &ep->fifo;
+ __le32 msg[2];
+
+ int rc = 0;
+
+ msg[0] = cpu_to_le32((chan_num & 0xfff) |
+ ((opcode & 0xf) << 24));
+ msg[1] = cpu_to_le32(data);
+
+ mutex_lock(&xdev->msg_mutex);
+
+ /*
+ * The wait queue is woken with the interruptible variant, so the
+ * wait function matches, however returning because of an interrupt
+ * will mess things up considerably, in particular when the caller is
+ * the release method. And the xdev->error part prevents being stuck
+ * forever: Just pull the USB plug.
+ */
+
+ while (wait_event_interruptible(fifo->waitq,
+ ((atomic_read(&fifo->fill)
+ <= (fifo->size - 8)) ||
+ xdev->error)))
+ ; /* Empty loop */
+
+ if (xdev->error) {
+ rc = xdev->error;
+ goto unlock_done;
+ }
+
+ fifo_write(fifo, (void *)msg, 8, xilly_memcpy);
+
+ try_queue_bulk_out(ep);
+
+unlock_done:
+ mutex_unlock(&xdev->msg_mutex);
+
+ return rc;
+}
+
+/*
+ * Note that flush_downstream() merely waits for the data to arrive to
+ * the application logic at the FPGA -- unlike PCIe Xillybus' counterpart,
+ * it does nothing to make it happen (and neither is it necessary).
+ *
+ * This function is not reentrant for the same @chan, but this is covered
+ * by the fact that for any given @chan, it's called either by the open,
+ * write, llseek and flush fops methods, which can't run in parallel (and the
+ * write + flush and llseek method handlers are protected with out_mutex).
+ *
+ * chan->flushed is there to avoid multiple flushes at the same position,
+ * in particular as a result of programs that close the file descriptor
+ * e.g. after a dup2() for redirection.
+ */
+
+static int flush_downstream(struct xillyusb_channel *chan,
+ long timeout,
+ bool interruptible)
+{
+ struct xillyusb_dev *xdev = chan->xdev;
+ int chan_num = chan->chan_idx << 1;
+ long deadline, left_to_sleep;
+ int rc;
+
+ if (chan->flushed)
+ return 0;
+
+ deadline = jiffies + 1 + timeout;
+
+ if (chan->flushing) {
+ long cancel_deadline = jiffies + 1 + XILLY_RESPONSE_TIMEOUT;
+
+ chan->canceled = 0;
+ rc = xillyusb_send_opcode(xdev, chan_num,
+ OPCODE_CANCEL_CHECKPOINT, 0);
+
+ if (rc)
+ return rc; /* Only real error, never -EINTR */
+
+ /* Ignoring interrupts. Cancellation must be handled */
+ while (!chan->canceled) {
+ left_to_sleep = cancel_deadline - ((long)jiffies);
+
+ if (left_to_sleep <= 0) {
+ report_io_error(xdev, -EIO);
+ pr_err("%s: Fatal error: Timed out on flush cancellation request.\n",
+ err_name);
+ return -EIO;
+ }
+
+ rc = wait_event_interruptible_timeout(chan->flushq,
+ chan->canceled ||
+ xdev->error,
+ left_to_sleep);
+
+ if (xdev->error)
+ return xdev->error;
+ }
+ }
+
+ chan->flushing = 1;
+
+ /*
+ * The checkpoint is given in terms of data elements, not bytes. As
+ * a result, if less than an element's worth of data is stored in the
+ * FIFO, it's not flushed, including the flush before closing, which
+ * means that such data is lost. This is consistent with PCIe Xillybus.
+ */
+
+ rc = xillyusb_send_opcode(xdev, chan_num,
+ OPCODE_SET_CHECKPOINT,
+ chan->out_bytes >>
+ chan->out_log2_element_size);
+
+ if (rc)
+ return rc; /* Only real error, never -EINTR */
+
+ if (!timeout) {
+ while (chan->flushing) {
+ rc = wait_event_interruptible(chan->flushq,
+ !chan->flushing ||
+ xdev->error);
+ if (xdev->error)
+ return xdev->error;
+
+ if (interruptible && rc)
+ return -EINTR;
+ }
+
+ goto done;
+ }
+
+ while (chan->flushing) {
+ left_to_sleep = deadline - ((long)jiffies);
+
+ if (left_to_sleep <= 0)
+ return -ETIMEDOUT;
+
+ rc = wait_event_interruptible_timeout(chan->flushq,
+ !chan->flushing ||
+ xdev->error,
+ left_to_sleep);
+
+ if (xdev->error)
+ return xdev->error;
+
+ if (interruptible && rc < 0)
+ return -EINTR;
+ }
+
+done:
+ chan->flushed = 1;
+ return 0;
+}
+
+/* request_read_anything(): Ask the FPGA for any little amount of data */
+static int request_read_anything(struct xillyusb_channel *chan,
+ char opcode)
+{
+ struct xillyusb_dev *xdev = chan->xdev;
+ unsigned int sh = chan->in_log2_element_size;
+ int chan_num = (chan->chan_idx << 1) | 1;
+ u32 mercy = chan->in_consumed_bytes + (2 << sh) - 1;
+
+ return xillyusb_send_opcode(xdev, chan_num, opcode, mercy >> sh);
+}
+
+static int xillyusb_open(struct inode *inode, struct file *filp)
+{
+ int minor = iminor(inode);
+ int major = imajor(inode);
+ struct xillyusb_dev *xdev_iter, *xdev = NULL;
+ struct xillyusb_channel *chan;
+ struct xillyfifo *in_fifo = NULL;
+ struct xillyusb_endpoint *out_ep = NULL;
+
+ int rc = -ENODEV;
+
+ mutex_lock(&xdev_mutex);
+
+ list_for_each_entry(xdev_iter, &xdev_list, list_entry) {
+ if (xdev_iter->major == major &&
+ minor >= xdev_iter->lowest_minor &&
+ minor < (xdev_iter->lowest_minor +
+ xdev_iter->num_channels)) {
+ xdev = xdev_iter;
+ break;
+ }
+ }
+
+ if (!xdev)
+ goto unmutex_fail;
+
+ chan = &xdev->channels[minor - xdev->lowest_minor];
+ filp->private_data = chan;
+
+ if (((filp->f_mode & FMODE_READ) && !chan->readable) ||
+ ((filp->f_mode & FMODE_WRITE) && !chan->writable))
+ goto unmutex_fail;
+
+ if ((filp->f_flags & O_NONBLOCK) && (filp->f_mode & FMODE_READ) &&
+ chan->in_synchronous) {
+ pr_err("%s: open() failed: O_NONBLOCK not allowed for read on this device\n",
+ err_name);
+ goto unmutex_fail;
+ }
+
+ if ((filp->f_flags & O_NONBLOCK) && (filp->f_mode & FMODE_WRITE) &&
+ chan->out_synchronous) {
+ pr_err("%s: open() failed: O_NONBLOCK not allowed for write on this device\n",
+ err_name);
+ goto unmutex_fail;
+ }
+
+ rc = -EBUSY;
+
+ if (((filp->f_mode & FMODE_READ) && chan->open_for_read) ||
+ ((filp->f_mode & FMODE_WRITE) && chan->open_for_write))
+ goto unmutex_fail;
+
+ kref_get(&xdev->kref);
+
+ if (filp->f_mode & FMODE_READ)
+ chan->open_for_read = 1;
+
+ if (filp->f_mode & FMODE_WRITE)
+ chan->open_for_write = 1;
+
+ mutex_unlock(&xdev_mutex);
+
+ if (filp->f_mode & FMODE_WRITE) {
+ out_ep = endpoint_alloc(xdev,
+ (chan->chan_idx + 2) | USB_DIR_OUT,
+ bulk_out_work, BUF_SIZE_ORDER, BUFNUM);
+
+ if (!out_ep) {
+ rc = -ENOMEM;
+ goto unopen;
+ }
+
+ rc = fifo_init(&out_ep->fifo, chan->out_log2_fifo_size);
+
+ if (rc)
+ goto late_unopen;
+
+ out_ep->fill_mask = -(1 << chan->out_log2_element_size);
+ chan->out_bytes = 0;
+ chan->flushed = 0;
+
+ /*
+ * Sending a flush request to a previously closed stream
+ * effectively opens it, and also waits until the command is
+ * confirmed by the FPGA. The latter is necessary because the
+ * data is sent through a separate BULK OUT endpoint, and the
+ * xHCI controller is free to reorder transmissions.
+ *
+ * This can't go wrong unless there's a serious hardware error
+ * (or the computer is stuck for 500 ms?)
+ */
+ rc = flush_downstream(chan, XILLY_RESPONSE_TIMEOUT, false);
+
+ if (rc == -ETIMEDOUT) {
+ rc = -EIO;
+ report_io_error(xdev, rc);
+ pr_err("%s: Fatal error: Hardware timed out to open request.\n",
+ err_name);
+ }
+
+ if (rc)
+ goto late_unopen;
+ }
+
+ if (filp->f_mode & FMODE_READ) {
+ in_fifo = kzalloc(sizeof(*in_fifo), GFP_KERNEL);
+
+ if (!in_fifo) {
+ rc = -ENOMEM;
+ goto late_unopen;
+ }
+
+ rc = fifo_init(in_fifo, chan->in_log2_fifo_size);
+
+ if (rc) {
+ kfree(in_fifo);
+ goto late_unopen;
+ }
+ }
+
+ mutex_lock(&chan->lock);
+ if (in_fifo) {
+ chan->in_fifo = in_fifo;
+ chan->read_data_ok = 1;
+ }
+ if (out_ep)
+ chan->out_ep = out_ep;
+ mutex_unlock(&chan->lock);
+
+ if (in_fifo) {
+ u32 in_checkpoint = 0;
+
+ if (!chan->in_synchronous)
+ in_checkpoint = in_fifo->size >>
+ chan->in_log2_element_size;
+
+ chan->in_consumed_bytes = 0;
+ chan->poll_used = 0;
+ chan->in_current_checkpoint = in_checkpoint;
+ rc = xillyusb_send_opcode(xdev, (chan->chan_idx << 1) | 1,
+ OPCODE_SET_CHECKPOINT,
+ in_checkpoint);
+
+ if (rc) /* Failure guarantees that opcode wasn't sent */
+ goto unfifo;
+
+ /*
+ * In non-blocking mode, request the FPGA to send any data it
+ * has right away. Otherwise, the first read() will always
+ * return -EAGAIN, which is OK strictly speaking, but ugly.
+ * Checking and unrolling if this fails isn't worth the
+ * effort -- the error is propagated to the first read()
+ * anyhow.
+ */
+ if (filp->f_flags & O_NONBLOCK)
+ request_read_anything(chan, OPCODE_SET_PUSH);
+ }
+
+ return 0;
+
+unfifo:
+ if (in_fifo) {
+ chan->read_data_ok = 0;
+ safely_assign_in_fifo(chan, NULL);
+ fifo_mem_release(in_fifo);
+ }
+
+ if (out_ep) {
+ mutex_lock(&chan->lock);
+ chan->out_ep = NULL;
+ mutex_unlock(&chan->lock);
+ }
+
+late_unopen:
+ if (out_ep)
+ endpoint_dealloc(out_ep);
+
+unopen:
+ mutex_lock(&xdev_mutex);
+
+ if (filp->f_mode & FMODE_READ)
+ chan->open_for_read = 0;
+
+ if (filp->f_mode & FMODE_WRITE)
+ chan->open_for_write = 0;
+
+ mutex_unlock(&xdev_mutex);
+
+ kref_put(&xdev->kref, cleanup_dev);
+
+ return rc;
+
+unmutex_fail:
+ mutex_unlock(&xdev_mutex);
+ return rc;
+}
+
+static int xilly_copy_to_user(void *dst, const void *src, int n)
+{
+ return copy_to_user((void __user *)dst, src, n);
+}
+
+static ssize_t xillyusb_read(struct file *filp, char __user *userbuf,
+ size_t count, loff_t *f_pos)
+{
+ struct xillyusb_channel *chan = filp->private_data;
+ struct xillyusb_dev *xdev = chan->xdev;
+ struct xillyfifo *fifo = chan->in_fifo;
+ int chan_num = (chan->chan_idx << 1) | 1;
+
+ long deadline, left_to_sleep;
+ int bytes_done = 0;
+ bool sent_set_push = false;
+ int rc;
+
+ deadline = jiffies + 1 + XILLY_RX_TIMEOUT;
+
+ rc = mutex_lock_interruptible(&chan->in_mutex);
+
+ if (rc)
+ return rc;
+
+ while (1) {
+ u32 fifo_checkpoint_bytes, complete_checkpoint_bytes;
+ u32 complete_checkpoint, fifo_checkpoint;
+ u32 checkpoint;
+ s32 diff, leap;
+ unsigned int sh = chan->in_log2_element_size;
+ bool checkpoint_for_complete;
+
+ rc = fifo_read(fifo, (__force void *)userbuf + bytes_done,
+ count - bytes_done, xilly_copy_to_user);
+
+ if (rc < 0)
+ break;
+
+ bytes_done += rc;
+ chan->in_consumed_bytes += rc;
+
+ left_to_sleep = deadline - ((long)jiffies);
+
+ /*
+ * Some 32-bit arithmetics that may wrap. Note that
+ * complete_checkpoint is rounded up to the closest element
+ * boundary, because the read() can't be completed otherwise.
+ * fifo_checkpoint_bytes is rounded down, because it protects
+ * in_fifo from overflowing.
+ */
+
+ fifo_checkpoint_bytes = chan->in_consumed_bytes + fifo->size;
+ complete_checkpoint_bytes =
+ chan->in_consumed_bytes + count - bytes_done;
+
+ fifo_checkpoint = fifo_checkpoint_bytes >> sh;
+ complete_checkpoint =
+ (complete_checkpoint_bytes + (1 << sh) - 1) >> sh;
+
+ diff = (fifo_checkpoint - complete_checkpoint) << sh;
+
+ if (chan->in_synchronous && diff >= 0) {
+ checkpoint = complete_checkpoint;
+ checkpoint_for_complete = true;
+ } else {
+ checkpoint = fifo_checkpoint;
+ checkpoint_for_complete = false;
+ }
+
+ leap = (checkpoint - chan->in_current_checkpoint) << sh;
+
+ /*
+ * To prevent flooding of OPCODE_SET_CHECKPOINT commands as
+ * data is consumed, it's issued only if it moves the
+ * checkpoint by at least an 8th of the FIFO's size, or if
+ * it's necessary to complete the number of bytes requested by
+ * the read() call.
+ *
+ * chan->read_data_ok is checked to spare an unnecessary
+ * submission after receiving EOF, however it's harmless if
+ * such slips away.
+ */
+
+ if (chan->read_data_ok &&
+ (leap > (fifo->size >> 3) ||
+ (checkpoint_for_complete && leap > 0))) {
+ chan->in_current_checkpoint = checkpoint;
+ rc = xillyusb_send_opcode(xdev, chan_num,
+ OPCODE_SET_CHECKPOINT,
+ checkpoint);
+
+ if (rc)
+ break;
+ }
+
+ if (bytes_done == count ||
+ (left_to_sleep <= 0 && bytes_done))
+ break;
+
+ /*
+ * Reaching here means that the FIFO was empty at the call to
+ * fifo_read() above, but not necessarily right now. Error
+ * and EOF are checked and reported only now, so that no data
+ * that managed its way to the FIFO is lost.
+ */
+
+ if (!READ_ONCE(chan->read_data_ok)) { /* FPGA has sent EOF */
+ /* Has data slipped into the FIFO since fifo_read()? */
+ smp_rmb();
+ if (atomic_read(&fifo->fill))
+ continue;
+
+ rc = 0;
+ break;
+ }
+
+ if (xdev->error) {
+ rc = xdev->error;
+ break;
+ }
+
+ if (filp->f_flags & O_NONBLOCK) {
+ rc = -EAGAIN;
+ break;
+ }
+
+ if (left_to_sleep > 0) {
+ if (!sent_set_push) {
+ rc = xillyusb_send_opcode(xdev, chan_num,
+ OPCODE_SET_PUSH,
+ complete_checkpoint);
+
+ if (rc)
+ break;
+
+ sent_set_push = true;
+ }
+
+ /*
+ * Note that when xdev->error is set (e.g. when the
+ * device is unplugged), read_data_ok turns zero and
+ * fifo->waitq is awaken.
+ * Therefore no special attention to xdev->error.
+ */
+
+ rc = wait_event_interruptible_timeout
+ (fifo->waitq,
+ atomic_read(&fifo->fill) ||
+ !chan->read_data_ok,
+ left_to_sleep);
+ } else { /* bytes_done == 0 */
+ /* Tell FPGA to send anything it has */
+ rc = request_read_anything(chan, OPCODE_UPDATE_PUSH);
+
+ if (rc)
+ break;
+
+ rc = wait_event_interruptible
+ (fifo->waitq,
+ atomic_read(&fifo->fill) ||
+ !chan->read_data_ok);
+ }
+
+ if (rc < 0) {
+ rc = -EINTR;
+ break;
+ }
+ }
+
+ if (((filp->f_flags & O_NONBLOCK) || chan->poll_used) &&
+ !atomic_read(&fifo->fill))
+ request_read_anything(chan, OPCODE_SET_PUSH);
+
+ mutex_unlock(&chan->in_mutex);
+
+ if (bytes_done)
+ return bytes_done;
+
+ return rc;
+}
+
+static int xillyusb_flush(struct file *filp, fl_owner_t id)
+{
+ struct xillyusb_channel *chan = filp->private_data;
+ int rc;
+
+ if (!(filp->f_mode & FMODE_WRITE))
+ return 0;
+
+ rc = mutex_lock_interruptible(&chan->out_mutex);
+
+ if (rc)
+ return rc;
+
+ /*
+ * One second's timeout on flushing. Interrupts are ignored, because if
+ * the user pressed CTRL-C, that interrupt will still be in flight by
+ * the time we reach here, and the opportunity to flush is lost.
+ */
+ rc = flush_downstream(chan, HZ, false);
+
+ if (rc == -ETIMEDOUT)
+ pr_warn("%s: Timed out while flushing. Output data may be lost.\n",
+ err_name);
+
+ mutex_unlock(&chan->out_mutex);
+
+ return rc;
+}
+
+static int xilly_copy_from_user(void *dst, const void *src, int n)
+{
+ return copy_from_user(dst, (const void __user *)src, n);
+}
+
+static ssize_t xillyusb_write(struct file *filp, const char __user *userbuf,
+ size_t count, loff_t *f_pos)
+{
+ struct xillyusb_channel *chan = filp->private_data;
+ struct xillyusb_dev *xdev = chan->xdev;
+ struct xillyfifo *fifo = &chan->out_ep->fifo;
+ int rc;
+
+ rc = mutex_lock_interruptible(&chan->out_mutex);
+
+ if (rc)
+ return rc;
+
+ while (1) {
+ if (xdev->error) {
+ rc = xdev->error;
+ break;
+ }
+
+ if (count == 0)
+ break;
+
+ rc = fifo_write(fifo, (__force void *)userbuf, count,
+ xilly_copy_from_user);
+
+ if (rc != 0)
+ break;
+
+ if (filp->f_flags & O_NONBLOCK) {
+ rc = -EAGAIN;
+ break;
+ }
+
+ if (wait_event_interruptible
+ (fifo->waitq,
+ (atomic_read(&fifo->fill) != fifo->size) ||
+ xdev->error)) {
+ rc = -EINTR;
+ break;
+ }
+ }
+
+ if (rc < 0)
+ goto done;
+
+ chan->out_bytes += rc;
+
+ if (rc) {
+ try_queue_bulk_out(chan->out_ep);
+ chan->flushed = 0;
+ }
+
+ if (chan->out_synchronous) {
+ int flush_rc = flush_downstream(chan, 0, true);
+
+ if (flush_rc && !rc)
+ rc = flush_rc;
+ }
+
+done:
+ mutex_unlock(&chan->out_mutex);
+
+ return rc;
+}
+
+static int xillyusb_release(struct inode *inode, struct file *filp)
+{
+ struct xillyusb_channel *chan = filp->private_data;
+ struct xillyusb_dev *xdev = chan->xdev;
+ int rc_read = 0, rc_write = 0;
+
+ if (filp->f_mode & FMODE_READ) {
+ struct xillyfifo *in_fifo = chan->in_fifo;
+
+ rc_read = xillyusb_send_opcode(xdev, (chan->chan_idx << 1) | 1,
+ OPCODE_CLOSE, 0);
+ /*
+ * If rc_read is nonzero, xdev->error indicates a global
+ * device error. The error is reported later, so that
+ * resources are freed.
+ *
+ * Looping on wait_event_interruptible() kinda breaks the idea
+ * of being interruptible, and this should have been
+ * wait_event(). Only it's being waken with
+ * wake_up_interruptible() for the sake of other uses. If
+ * there's a global device error, chan->read_data_ok is
+ * deasserted and the wait queue is awaken, so this is covered.
+ */
+
+ while (wait_event_interruptible(in_fifo->waitq,
+ !chan->read_data_ok))
+ ; /* Empty loop */
+
+ safely_assign_in_fifo(chan, NULL);
+ fifo_mem_release(in_fifo);
+
+ mutex_lock(&xdev_mutex);
+ chan->open_for_read = 0;
+ mutex_unlock(&xdev_mutex);
+ }
+
+ if (filp->f_mode & FMODE_WRITE) {
+ struct xillyusb_endpoint *ep = chan->out_ep;
+ /*
+ * chan->flushing isn't zeroed. If the pre-release flush timed
+ * out, a cancel request will be sent before the next
+ * OPCODE_SET_CHECKPOINT (i.e. when the file is opened again).
+ * This is despite that the FPGA forgets about the checkpoint
+ * request as the file closes. Still, in an exceptional race
+ * condition, the FPGA could send an OPCODE_REACHED_CHECKPOINT
+ * just before closing that would reach the host after the
+ * file has re-opened.
+ */
+
+ mutex_lock(&chan->lock);
+ chan->out_ep = NULL;
+ mutex_unlock(&chan->lock);
+
+ endpoint_dealloc(ep);
+
+ /* See comments on rc_read above */
+ rc_write = xillyusb_send_opcode(xdev, chan->chan_idx << 1,
+ OPCODE_CLOSE, 0);
+
+ mutex_lock(&xdev_mutex);
+ chan->open_for_write = 0;
+ mutex_unlock(&xdev_mutex);
+ }
+
+ kref_put(&xdev->kref, cleanup_dev);
+
+ return rc_read ? rc_read : rc_write;
+}
+
+static loff_t xillyusb_llseek(struct file *filp, loff_t offset, int whence)
+{
+ struct xillyusb_channel *chan = filp->private_data;
+ struct xillyusb_dev *xdev = chan->xdev;
+ loff_t pos = filp->f_pos;
+ int rc = 0;
+ unsigned int log2_element_size = chan->readable ?
+ chan->in_log2_element_size : chan->out_log2_element_size;
+
+ /*
+ * Take both mutexes not allowing interrupts, since it seems like
+ * common applications don't expect an -EINTR here. Besides, multiple
+ * access to a single file descriptor on seekable devices is a mess
+ * anyhow.
+ */
+
+ mutex_lock(&chan->out_mutex);
+ mutex_lock(&chan->in_mutex);
+
+ switch (whence) {
+ case SEEK_SET:
+ pos = offset;
+ break;
+ case SEEK_CUR:
+ pos += offset;
+ break;
+ case SEEK_END:
+ pos = offset; /* Going to the end => to the beginning */
+ break;
+ default:
+ rc = -EINVAL;
+ goto end;
+ }
+
+ /* In any case, we must finish on an element boundary */
+ if (pos & ((1 << log2_element_size) - 1)) {
+ rc = -EINVAL;
+ goto end;
+ }
+
+ rc = xillyusb_send_opcode(xdev, chan->chan_idx << 1,
+ OPCODE_SET_ADDR,
+ pos >> log2_element_size);
+
+ if (rc)
+ goto end;
+
+ /*
+ * If the stream is writable (it most likely is), a flush request is
+ * sent to ensure that traffic on the stream's BULK OUT endpoint isn't
+ * sent before the position is updated on the FPGA -- otherwise that
+ * data could arrive before the position update. Since only
+ * synchronous streams can be seekable, flush_downstream() has already
+ * been called after the last write(), so flushing is completed
+ * virtually right away. Well, unless the last flush was interrupted,
+ * in which case we wait for up to 1000 ms, and return -ETIMEDOUT (!)
+ * if the flush was incomplete. No real-life application should ever
+ * get to this point.
+ */
+
+ if (chan->writable) {
+ chan->flushed = 0;
+ rc = flush_downstream(chan, HZ, false);
+ }
+
+end:
+ mutex_unlock(&chan->out_mutex);
+ mutex_unlock(&chan->in_mutex);
+
+ if (rc) /* Return error after releasing mutexes */
+ return rc;
+
+ filp->f_pos = pos;
+
+ return pos;
+}
+
+static __poll_t xillyusb_poll(struct file *filp, poll_table *wait)
+{
+ struct xillyusb_channel *chan = filp->private_data;
+ __poll_t mask = 0;
+
+ if (chan->in_fifo)
+ poll_wait(filp, &chan->in_fifo->waitq, wait);
+
+ if (chan->out_ep)
+ poll_wait(filp, &chan->out_ep->fifo.waitq, wait);
+
+ /*
+ * If this is the first time poll() is called, and the file is
+ * readable, set the relevant flag. Also tell the FPGA to send all it
+ * has, to kickstart the mechanism that ensures there's always some
+ * data in in_fifo unless the stream is dry end-to-end. Note that the
+ * first poll() may not return a EPOLLIN, even if there's data on the
+ * FPGA. Rather, the data will arrive soon, and trigger the relevant
+ * wait queue.
+ */
+
+ if (!chan->poll_used && chan->in_fifo) {
+ chan->poll_used = 1;
+ request_read_anything(chan, OPCODE_SET_PUSH);
+ }
+
+ /*
+ * poll() won't play ball regarding read() channels which
+ * are synchronous. Allowing that will create situations where data has
+ * been delivered at the FPGA, and users expecting select() to wake up,
+ * which it may not. So make it never work.
+ */
+
+ if (chan->in_fifo && !chan->in_synchronous &&
+ (atomic_read(&chan->in_fifo->fill) || !chan->read_data_ok))
+ mask |= EPOLLIN | EPOLLRDNORM;
+
+ if (chan->out_ep &&
+ (atomic_read(&chan->out_ep->fifo.fill) !=
+ chan->out_ep->fifo.size))
+ mask |= EPOLLOUT | EPOLLWRNORM;
+
+ if (chan->xdev->error)
+ mask |= EPOLLERR;
+
+ return mask;
+}
+
+static const struct file_operations xillyusb_fops = {
+ .owner = THIS_MODULE,
+ .read = xillyusb_read,
+ .write = xillyusb_write,
+ .open = xillyusb_open,
+ .flush = xillyusb_flush,
+ .release = xillyusb_release,
+ .llseek = xillyusb_llseek,
+ .poll = xillyusb_poll,
+};
+
+/*
+ * Called from xillyusb_probe() only, hence interface->dev is guaranteed to
+ * be valid.
+ */
+
+static int xillyusb_init_chrdev(struct usb_interface *interface,
+ unsigned char *names,
+ unsigned int len)
+{
+ int rc;
+ dev_t dev;
+ int i;
+ char devname[48];
+ struct device *device;
+ size_t namelen;
+
+ struct xillyusb_dev *xdev = usb_get_intfdata(interface);
+
+ rc = alloc_chrdev_region(&dev, 0, /* minor start */
+ xdev->num_channels,
+ xillyname);
+ if (rc) {
+ dev_warn(&interface->dev, "Failed to obtain major/minors");
+ return rc;
+ }
+
+ /* With cdev_alloc(), the allocated memory is freed automatically */
+ xdev->cdev = cdev_alloc();
+ if (!xdev->cdev)
+ goto unregister_chrdev;
+
+ xdev->cdev->ops = &xillyusb_fops;
+ xdev->cdev->owner = THIS_MODULE;
+
+ xdev->major = MAJOR(dev);
+ xdev->lowest_minor = MINOR(dev);
+
+ rc = cdev_add(xdev->cdev, MKDEV(xdev->major, xdev->lowest_minor),
+ xdev->num_channels);
+ if (rc) {
+ dev_warn(&interface->dev, "Failed to add cdev. Aborting.\n");
+ /* kobject_put() is normally done by cdev_del() */
+ kobject_put(&xdev->cdev->kobj);
+ goto unregister_chrdev;
+ }
+
+ for (i = 0; i < xdev->num_channels; i++) {
+ namelen = strnlen(names, len);
+
+ if (namelen == len) {
+ dev_err(&interface->dev, "IDT's list of names is too short. This is exceptionally weird, because its CRC is OK\n");
+ rc = -ENODEV;
+ goto unroll_device_create;
+ }
+
+ snprintf(devname, sizeof(devname) - 1, "xillyusb_%02d_%s",
+ xdev->index, names);
+
+ devname[sizeof(devname) - 1] = 0; /* Should never matter */
+
+ len -= namelen + 1;
+ names += namelen + 1;
+
+ device = device_create(xillyusb_class,
+ NULL,
+ MKDEV(xdev->major,
+ i + xdev->lowest_minor),
+ NULL,
+ "%s", devname);
+
+ if (IS_ERR(device)) {
+ dev_err(&interface->dev,
+ "Failed to create %s device. Aborting.\n",
+ devname);
+ rc = -ENODEV;
+ goto unroll_device_create;
+ }
+ }
+
+ dev_info(&interface->dev, "Created %d device files.\n",
+ xdev->num_channels);
+ return 0; /* succeed */
+
+unroll_device_create:
+ for (i--; i >= 0; i--)
+ device_destroy(xillyusb_class, MKDEV(xdev->major,
+ i + xdev->lowest_minor));
+
+ cdev_del(xdev->cdev);
+unregister_chrdev:
+ unregister_chrdev_region(MKDEV(xdev->major, xdev->lowest_minor),
+ xdev->num_channels);
+
+ return rc;
+}
+
+/*
+ * Called from xillyusb_disconnect() only, hence interface->dev is
+ * guaranteed to be valid.
+ */
+
+static void xillyusb_cleanup_chrdev(struct usb_interface *interface)
+{
+ int minor;
+ struct xillyusb_dev *xdev = usb_get_intfdata(interface);
+
+ for (minor = xdev->lowest_minor;
+ minor < (xdev->lowest_minor + xdev->num_channels);
+ minor++)
+ device_destroy(xillyusb_class, MKDEV(xdev->major, minor));
+ cdev_del(xdev->cdev);
+ unregister_chrdev_region(MKDEV(xdev->major,
+ xdev->lowest_minor),
+ xdev->num_channels);
+
+ dev_info(&interface->dev, "Removed %d device files.\n",
+ xdev->num_channels);
+}
+
+static int xillyusb_setup_base_eps(struct xillyusb_dev *xdev)
+{
+ xdev->msg_ep = endpoint_alloc(xdev, MSG_EP_NUM | USB_DIR_OUT,
+ bulk_out_work, 1, 2);
+ if (!xdev->msg_ep)
+ return -ENOMEM;
+
+ if (fifo_init(&xdev->msg_ep->fifo, 13)) /* 8 kiB */
+ goto dealloc;
+
+ xdev->msg_ep->fill_mask = -8; /* 8 bytes granularity */
+
+ xdev->in_ep = endpoint_alloc(xdev, IN_EP_NUM | USB_DIR_IN,
+ bulk_in_work, BUF_SIZE_ORDER, BUFNUM);
+ if (!xdev->in_ep)
+ goto dealloc;
+
+ try_queue_bulk_in(xdev->in_ep);
+
+ return 0;
+
+dealloc:
+ endpoint_dealloc(xdev->msg_ep); /* Also frees FIFO mem if allocated */
+ return -ENOMEM;
+}
+
+static int setup_channels(struct xillyusb_dev *xdev,
+ __le16 *chandesc)
+{
+ struct xillyusb_channel *chan;
+ int i;
+
+ chan = kcalloc(xdev->num_channels, sizeof(*chan), GFP_KERNEL);
+ if (!chan)
+ return -ENOMEM;
+
+ xdev->channels = chan;
+
+ for (i = 0; i < xdev->num_channels; i++, chan++) {
+ unsigned int in_desc = le16_to_cpu(*chandesc++);
+ unsigned int out_desc = le16_to_cpu(*chandesc++);
+
+ chan->xdev = xdev;
+ mutex_init(&chan->in_mutex);
+ mutex_init(&chan->out_mutex);
+ mutex_init(&chan->lock);
+ init_waitqueue_head(&chan->flushq);
+
+ chan->chan_idx = i;
+
+ if (in_desc & 0x80) { /* Entry is valid */
+ chan->readable = 1;
+ chan->in_synchronous = !!(in_desc & 0x40);
+ chan->in_seekable = !!(in_desc & 0x20);
+ chan->in_log2_element_size = in_desc & 0x0f;
+ chan->in_log2_fifo_size = ((in_desc >> 8) & 0x1f) + 16;
+ }
+
+ if (out_desc & 0x80) { /* Entry is valid */
+ chan->writable = 1;
+ chan->out_synchronous = !!(out_desc & 0x40);
+ chan->out_seekable = !!(out_desc & 0x20);
+ chan->out_log2_element_size = out_desc & 0x0f;
+ chan->out_log2_fifo_size =
+ ((out_desc >> 8) & 0x1f) + 16;
+ }
+ }
+
+ return 0;
+}
+
+static int xillyusb_discovery(struct usb_interface *interface)
+{
+ int rc;
+ struct xillyusb_dev *xdev = usb_get_intfdata(interface);
+ __le16 bogus_chandesc[2];
+ struct xillyfifo idt_fifo;
+ struct xillyusb_channel *chan;
+ unsigned int idt_len, names_offset;
+ unsigned char *idt;
+
+ rc = xillyusb_send_opcode(xdev, ~0, OPCODE_QUIESCE, 0);
+
+ if (rc) {
+ dev_err(&interface->dev, "Failed to send quiesce request. Aborting.\n");
+ return rc;
+ }
+
+ /* Phase I: Set up one fake upstream channel and obtain IDT */
+
+ /* Set up a fake IDT with one async IN stream */
+ xdev->num_channels = 1;
+ bogus_chandesc[0] = cpu_to_le16(0x80);
+ bogus_chandesc[1] = cpu_to_le16(0);
+
+ rc = setup_channels(xdev, bogus_chandesc);
+
+ if (rc)
+ return rc;
+
+ rc = fifo_init(&idt_fifo, LOG2_IDT_FIFO_SIZE);
+
+ if (rc)
+ return rc;
+
+ chan = xdev->channels;
+
+ chan->in_fifo = &idt_fifo;
+ chan->read_data_ok = 1;
+
+ rc = xillyusb_send_opcode(xdev, ~0, OPCODE_REQ_IDT, 0);
+
+ if (rc) {
+ dev_err(&interface->dev, "Failed to send IDT request. Aborting.\n");
+ goto unfifo;
+ }
+
+ rc = wait_event_interruptible_timeout(idt_fifo.waitq,
+ !chan->read_data_ok,
+ XILLY_RESPONSE_TIMEOUT);
+
+ if (xdev->error) {
+ rc = xdev->error;
+ goto unfifo;
+ }
+
+ if (rc < 0) {
+ rc = -EINTR; /* Interrupt on probe method? Interesting. */
+ goto unfifo;
+ }
+
+ if (chan->read_data_ok) {
+ rc = -ETIMEDOUT;
+ dev_err(&interface->dev, "No response from FPGA. Aborting.\n");
+ goto unfifo;
+ }
+
+ idt_len = atomic_read(&idt_fifo.fill);
+ idt = kmalloc(idt_len, GFP_KERNEL);
+
+ if (!idt)
+ goto unfifo;
+
+ fifo_read(&idt_fifo, idt, idt_len, xilly_memcpy);
+
+ if (crc32_le(~0, idt, idt_len) != 0) {
+ dev_err(&interface->dev, "IDT failed CRC check. Aborting.\n");
+ rc = -ENODEV;
+ goto unidt;
+ }
+
+ if (*idt > 0x90) {
+ dev_err(&interface->dev, "No support for IDT version 0x%02x. Maybe the xillyusb driver needs an upgarde. Aborting.\n",
+ (int)*idt);
+ rc = -ENODEV;
+ goto unidt;
+ }
+
+ /* Phase II: Set up the streams as defined in IDT */
+
+ xdev->num_channels = le16_to_cpu(*((__le16 *)(idt + 1)));
+ names_offset = 3 + xdev->num_channels * 4;
+ idt_len -= 4; /* Exclude CRC */
+
+ if (idt_len < names_offset) {
+ dev_err(&interface->dev, "IDT too short. This is exceptionally weird, because its CRC is OK\n");
+ rc = -ENODEV;
+ goto unidt;
+ }
+
+ rc = setup_channels(xdev, (void *)idt + 3);
+
+ if (rc)
+ goto unidt;
+
+ /*
+ * Except for wildly misbehaving hardware, or if it was disconnected
+ * just after responding with the IDT, there is no reason for any
+ * work item to be running now. To be sure that xdev->channel
+ * is updated on anything that might run in parallel, flush the
+ * workqueue, which rarely does anything.
+ */
+ flush_workqueue(xdev->workq);
+
+ fifo_mem_release(&idt_fifo);
+ kfree(chan);
+
+ rc = xillyusb_init_chrdev(interface, idt + names_offset,
+ idt_len - names_offset);
+
+ kfree(idt);
+
+ return rc;
+
+unidt:
+ kfree(idt);
+
+unfifo:
+ safely_assign_in_fifo(chan, NULL);
+ fifo_mem_release(&idt_fifo);
+
+ return rc;
+}
+
+static int xillyusb_probe(struct usb_interface *interface,
+ const struct usb_device_id *id)
+{
+ struct xillyusb_dev *xdev;
+ int rc;
+ int i;
+
+ xdev = kzalloc(sizeof(*xdev), GFP_KERNEL);
+ if (!xdev)
+ return -ENOMEM;
+
+ kref_init(&xdev->kref);
+ mutex_init(&xdev->io_mutex);
+ mutex_init(&xdev->process_in_mutex);
+ mutex_init(&xdev->msg_mutex);
+
+ xdev->udev = usb_get_dev(interface_to_usbdev(interface));
+ xdev->interface = interface;
+ xdev->error = 0;
+ spin_lock_init(&xdev->error_lock);
+ xdev->in_counter = 0;
+ xdev->in_bytes_left = 0;
+ xdev->workq = alloc_workqueue(xillyname, WQ_HIGHPRI, 0);
+
+ if (!xdev->workq) {
+ dev_err(&interface->dev, "Failed to allocate work queue\n");
+ rc = -ENOMEM;
+ goto fail;
+ }
+
+ INIT_WORK(&xdev->wakeup_workitem, wakeup_all);
+
+ usb_set_intfdata(interface, xdev);
+
+ mutex_lock(&xdev_mutex);
+
+ for (i = 0; i < MAX_XILLYUSB_DEVS; i++)
+ if (!xdev_map[i])
+ break;
+
+ if (i == MAX_XILLYUSB_DEVS) {
+ dev_err(&interface->dev,
+ "Reached limit of %d maximal devices. Aborting.\n",
+ MAX_XILLYUSB_DEVS);
+ mutex_unlock(&xdev_mutex);
+ rc = -ENODEV;
+ goto fail;
+ }
+
+ xdev_map[i] = 1;
+
+ mutex_unlock(&xdev_mutex);
+
+ xdev->index = i;
+
+ rc = xillyusb_setup_base_eps(xdev);
+
+ if (rc)
+ goto unindex_fail;
+
+ rc = xillyusb_discovery(interface);
+
+ if (rc)
+ goto unindex_fail;
+
+ mutex_lock(&xdev_mutex);
+ list_add_tail(&xdev->list_entry, &xdev_list);
+ mutex_unlock(&xdev_mutex);
+
+ return 0;
+
+unindex_fail:
+ xdev_map[i] = 0;
+
+fail:
+ usb_set_intfdata(interface, NULL);
+ kref_put(&xdev->kref, cleanup_dev);
+ return rc;
+}
+
+static void xillyusb_disconnect(struct usb_interface *interface)
+{
+ struct xillyusb_dev *xdev;
+
+ xillyusb_cleanup_chrdev(interface);
+
+ xdev = usb_get_intfdata(interface);
+
+ /*
+ * Try to send OPCODE_QUIESCE, which will fail silently if the device
+ * was disconnected, but makes sense on module unload.
+ */
+
+ xillyusb_send_opcode(xdev, ~0, OPCODE_QUIESCE, 0);
+
+ usb_set_intfdata(interface, NULL);
+
+ report_io_error(xdev, -ENODEV);
+
+ mutex_lock(&xdev->io_mutex);
+ xdev->interface = NULL;
+ mutex_unlock(&xdev->io_mutex);
+
+ mutex_lock(&xdev_mutex);
+ xdev_map[xdev->index] = 0;
+ list_del(&xdev->list_entry);
+ mutex_unlock(&xdev_mutex);
+
+ kref_put(&xdev->kref, cleanup_dev);
+}
+
+static struct usb_driver xillyusb_driver = {
+ .name = xillyname,
+ .id_table = xillyusb_table,
+ .probe = xillyusb_probe,
+ .disconnect = xillyusb_disconnect,
+};
+
+static int __init xillyusb_init(void)
+{
+ int rc = 0;
+
+ int i;
+
+ if (LOG2_INITIAL_FIFO_BUF_SIZE > PAGE_SHIFT)
+ fifo_buf_order = LOG2_INITIAL_FIFO_BUF_SIZE - PAGE_SHIFT;
+ else
+ fifo_buf_order = 0;
+
+ for (i = 0; i < MAX_XILLYUSB_DEVS; i++)
+ xdev_map[i] = 0;
+
+ xillyusb_class = class_create(THIS_MODULE, xillyname);
+ if (IS_ERR(xillyusb_class)) {
+ rc = PTR_ERR(xillyusb_class);
+ pr_warn("Failed to register class xillyusb\n");
+
+ return rc;
+ }
+ rc = usb_register(&xillyusb_driver);
+
+ if (rc) {
+ class_destroy(xillyusb_class);
+ return rc;
+ }
+
+ return rc;
+}
+
+static void __exit xillyusb_exit(void)
+{
+ usb_deregister(&xillyusb_driver);
+ class_destroy(xillyusb_class);
+}
+
+module_init(xillyusb_init);
+module_exit(xillyusb_exit);
--
2.17.1
On Mon, Feb 01, 2021 at 04:16:51PM +0200, [email protected] wrote:
> From: Eli Billauer <[email protected]>
>
> The XillyUSB driver is the USB variant for the Xillybus FPGA IP core.
> Even though it presents a nearly identical API on the FPGA and host,
> it's almost a complete rewrite of the driver: The framework for exchanging
> data on a USB bus is fundamentally different from doing the same with a
> PCIe interface, which leaves very little in common between the existing
> driver and the new one for XillyUSB.
As this has nothing to do with the existing XillyBus code, and you
aren't doing anything "fancy" with the character device nodes, why does
this need to be a kernel driver at all? Why can't you just use libusb
and talk to the device directly from userspace with no kernel driver
needed?
And always cc: [email protected] when submitting a USB driver so
that the developers there can review it.
thanks,
greg k-h
Hello, Greg.
On 01/02/21 16:25, Greg KH wrote:
> As this has nothing to do with the existing XillyBus code, and you
> aren't doing anything "fancy" with the character device nodes, why does
> this need to be a kernel driver at all? Why can't you just use libusb
> and talk to the device directly from userspace with no kernel driver
> needed?
>
That's actually what I did in my first attempt.
However in order to provide the same API as the existing Xillybus
driver, this driver must present some kind of device files.
Named pipes aren't sufficient, among others because closing a Xillybus
device file is something that the hardware is informed about
immediately. Also, when a device file is opened for write, the close()
call should not return until all data has arrived to hardware (per
existing API). This can't be guaranteed with named pipes.
So a user-space driver needs to rely on CUSE. Which I wasted two months
on before realizing it's not stable enough to rely upon. My whines on
CUSE can be found in my blog:
http://billauer.co.il/blog/2020/02/linux-cuse-fuse-libfuse-crash/
> And always cc:[email protected] when submitting a USB driver so
> that the developers there can review it.
>
Sorry, I wasn't aware of that. Will resend this patch with this list
cc'ed shortly.
Thanks,
Eli
On Mon, Feb 01, 2021 at 05:56:38PM +0200, Eli Billauer wrote:
> Hello, Greg.
>
> On 01/02/21 16:25, Greg KH wrote:
> > As this has nothing to do with the existing XillyBus code, and you
> > aren't doing anything "fancy" with the character device nodes, why does
> > this need to be a kernel driver at all? Why can't you just use libusb
> > and talk to the device directly from userspace with no kernel driver
> > needed?
> That's actually what I did in my first attempt.
>
> However in order to provide the same API as the existing Xillybus driver,
> this driver must present some kind of device files.
But you are not providing the same API! Or so you are saying in the
driver.
If you were, then you need to use the same device nodes that the
existing xillybus code uses and share them. Which is what I asked about
before.
> Named pipes aren't sufficient, among others because closing a Xillybus
> device file is something that the hardware is informed about immediately.
> Also, when a device file is opened for write, the close() call should not
> return until all data has arrived to hardware (per existing API). This can't
> be guaranteed with named pipes.
What does a named pipe have to do with anything here?
> So a user-space driver needs to rely on CUSE. Which I wasted two months on
> before realizing it's not stable enough to rely upon. My whines on CUSE can
> be found in my blog:
Why is cuse an issue here?
Just use libusb and have your userspace programs link against it.
thanks,
greg k-h