Hi Andrew,
On 11/09/23 18:35, Andrew Davis wrote:
> On 9/11/23 2:12 AM, MD Danish Anwar wrote:
>> ICSSG2 provides dual Gigabit Ethernet support.
>>
>> For support SR2.0 ICSSG Ethernet firmware:
>> - provide different firmware blobs and use TX_PRU.
>> - IEP0 is used as PTP Hardware Clock and can only be used for one port.
>> - TX timestamp notification comes via INTC interrupt.
>>
>> Signed-off-by: MD Danish Anwar <[email protected]>
>> ---
>> .../arm64/boot/dts/ti/k3-am654-base-board.dts | 123 ++++++++++++++++++
>
> Adding this to the base dts? What if I want to use my PRUs for something
> else? These "application nodes" define a single usecase out of many
> possible, and should IMHO always be in overlays so users can select which
> they want easily.
>
The base board (AM654x-EVM) has two Ethernet ports dedicated for ICSSG.
The expectation is that when a user boots up AM654x-EVM, ICSSG is
supported on those two ports by default. If the icssg nodes are not
added to base dts then by default the two Ethernet ports will have no
functionality.
The primary use case is that ICSSG should support on those two ports in
AM654x-EVM by default. The user should not need to apply any overlay to
get the two ports working. So In order to achieve that I think it is OK
to add the ICSSG nodes in the base board dts file.
If user wants to use PRUs for something else, we can have overlay for
those. But we should not need to apply any overlay to achieve the
primary functionality i.e. ICSSG working in the two dedicated ICSSG
Ethernet ports.
> Andrew
>
>> 1 file changed, 123 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
>> b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
>> index f5c26e9fba98..5cf9546ff9f7 100644
>> --- a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
>> +++ b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
>> @@ -25,6 +25,8 @@ aliases {
>> ethernet0 = &cpsw_port1;
>> mmc0 = &sdhci0;
>> mmc1 = &sdhci1;
>> + ethernet1 = &icssg2_emac0;
>> + ethernet2 = &icssg2_emac1;
>> };
>> chosen {
>> @@ -144,6 +146,72 @@ vtt_supply: regulator-3 {
>> vin-supply = <&vcc3v3_io>;
>> gpio = <&wkup_gpio0 28 GPIO_ACTIVE_HIGH>;
>> };
>> +
>> + /* Dual Ethernet application node on PRU-ICSSG2 */
>> + icssg2_eth: icssg2-eth {
>> + compatible = "ti,am654-icssg-prueth";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&icssg2_rgmii_pins_default>;
>> + sram = <&msmc_ram>;
>> + ti,prus = <&pru2_0>, <&rtu2_0>, <&tx_pru2_0>,
>> + <&pru2_1>, <&rtu2_1>, <&tx_pru2_1>;
>> + firmware-name = "ti-pruss/am65x-sr2-pru0-prueth-fw.elf",
>> + "ti-pruss/am65x-sr2-rtu0-prueth-fw.elf",
>> + "ti-pruss/am65x-sr2-txpru0-prueth-fw.elf",
>> + "ti-pruss/am65x-sr2-pru1-prueth-fw.elf",
>> + "ti-pruss/am65x-sr2-rtu1-prueth-fw.elf",
>> + "ti-pruss/am65x-sr2-txpru1-prueth-fw.elf";
>> +
>> + ti,pruss-gp-mux-sel = <2>, /* MII mode */
>> + <2>,
>> + <2>,
>> + <2>, /* MII mode */
>> + <2>,
>> + <2>;
>> +
>> + ti,mii-g-rt = <&icssg2_mii_g_rt>;
>> + ti,mii-rt = <&icssg2_mii_rt>;
>> + ti,iep = <&icssg2_iep0>, <&icssg2_iep1>;
>> +
>> + interrupt-parent = <&icssg2_intc>;
>> + interrupts = <24 0 2>, <25 1 3>;
>> + interrupt-names = "tx_ts0", "tx_ts1";
>> +
>> + dmas = <&main_udmap 0xc300>, /* egress slice 0 */
>> + <&main_udmap 0xc301>, /* egress slice 0 */
>> + <&main_udmap 0xc302>, /* egress slice 0 */
>> + <&main_udmap 0xc303>, /* egress slice 0 */
>> + <&main_udmap 0xc304>, /* egress slice 1 */
>> + <&main_udmap 0xc305>, /* egress slice 1 */
>> + <&main_udmap 0xc306>, /* egress slice 1 */
>> + <&main_udmap 0xc307>, /* egress slice 1 */
>> + <&main_udmap 0x4300>, /* ingress slice 0 */
>> + <&main_udmap 0x4301>; /* ingress slice 1 */
>> +
>> + dma-names = "tx0-0", "tx0-1", "tx0-2", "tx0-3",
>> + "tx1-0", "tx1-1", "tx1-2", "tx1-3",
>> + "rx0", "rx1";
>> + ethernet-ports {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + icssg2_emac0: port@0 {
>> + reg = <0>;
>> + phy-handle = <&icssg2_phy0>;
>> + phy-mode = "rgmii-id";
>> + ti,syscon-rgmii-delay = <&scm_conf 0x4120>;
>> + /* Filled in by bootloader */
>> + local-mac-address = [00 00 00 00 00 00];
>> + };
>> + icssg2_emac1: port@1 {
>> + reg = <1>;
>> + phy-handle = <&icssg2_phy1>;
>> + phy-mode = "rgmii-id";
>> + ti,syscon-rgmii-delay = <&scm_conf 0x4124>;
>> + /* Filled in by bootloader */
>> + local-mac-address = [00 00 00 00 00 00];
>> + };
>> + };
>> + };
>> };
>> &wkup_pmx0 {
>> @@ -300,6 +368,43 @@ usb1_pins_default: usb1-default-pins {
>> AM65X_IOPAD(0x02c0, PIN_OUTPUT, 0) /* (AC8) USB1_DRVVBUS */
>> >;
>> };
>> +
>> + icssg2_mdio_pins_default: icssg2-mdio-default-pins {
>> + pinctrl-single,pins = <
>> + AM65X_IOPAD(0x0094, PIN_INPUT, 2) /* (AC19)
>> PRG2_PRU0_GPO7.PRG2_MDIO0_MDIO */
>> + AM65X_IOPAD(0x00c8, PIN_OUTPUT, 2) /* (AE15)
>> PRG2_PRU1_GPO7.PRG2_MDIO0_MDC */
>> + >;
>> + };
>> +
>> + icssg2_rgmii_pins_default: icssg2-rgmii-default-pins {
>> + pinctrl-single,pins = <
>> + AM65X_IOPAD(0x00ac, PIN_INPUT, 2) /* (AH15)
>> PRG2_PRU1_GPO0.PRG2_RGMII2_RD0 */
>> + AM65X_IOPAD(0x00b0, PIN_INPUT, 2) /* (AC16)
>> PRG2_PRU1_GPO1.PRG2_RGMII2_RD1 */
>> + AM65X_IOPAD(0x00b4, PIN_INPUT, 2) /* (AD17)
>> PRG2_PRU1_GPO2.PRG2_RGMII2_RD2 */
>> + AM65X_IOPAD(0x00b8, PIN_INPUT, 2) /* (AH14)
>> PRG2_PRU1_GPO3.PRG2_RGMII2_RD3 */
>> + AM65X_IOPAD(0x00cc, PIN_OUTPUT, 2) /* (AD15)
>> PRG2_PRU1_GPO8.PRG2_RGMII2_TD0 */
>> + AM65X_IOPAD(0x00d0, PIN_OUTPUT, 2) /* (AF14)
>> PRG2_PRU1_GPO9.PRG2_RGMII2_TD1 */
>> + AM65X_IOPAD(0x00d4, PIN_OUTPUT, 2) /* (AC15)
>> PRG2_PRU1_GPO10.PRG2_RGMII2_TD2 */
>> + AM65X_IOPAD(0x00d8, PIN_OUTPUT, 2) /* (AD14)
>> PRG2_PRU1_GPO11.PRG2_RGMII2_TD3 */
>> + AM65X_IOPAD(0x00dc, PIN_INPUT, 2) /* (AE14)
>> PRG2_PRU1_GPO16.PRG2_RGMII2_TXC */
>> + AM65X_IOPAD(0x00c4, PIN_OUTPUT, 2) /* (AC17)
>> PRG2_PRU1_GPO6.PRG2_RGMII2_TX_CTL */
>> + AM65X_IOPAD(0x00c0, PIN_INPUT, 2) /* (AG15)
>> PRG2_PRU1_GPO5.PRG2_RGMII2_RXC */
>> + AM65X_IOPAD(0x00bc, PIN_INPUT, 2) /* (AG14)
>> PRG2_PRU1_GPO4.PRG2_RGMII2_RX_CTL */
>> +
>> + AM65X_IOPAD(0x0078, PIN_INPUT, 2) /* (AF18)
>> PRG2_PRU0_GPO0.PRG2_RGMII1_RD0 */
>> + AM65X_IOPAD(0x007c, PIN_INPUT, 2) /* (AE18)
>> PRG2_PRU0_GPO1.PRG2_RGMII1_RD1 */
>> + AM65X_IOPAD(0x0080, PIN_INPUT, 2) /* (AH17)
>> PRG2_PRU0_GPO2.PRG2_RGMII1_RD2 */
>> + AM65X_IOPAD(0x0084, PIN_INPUT, 2) /* (AG18)
>> PRG2_PRU0_GPO3.PRG2_RGMII1_RD3 */
>> + AM65X_IOPAD(0x0098, PIN_OUTPUT, 2) /* (AH16)
>> PRG2_PRU0_GPO8.PRG2_RGMII1_TD0 */
>> + AM65X_IOPAD(0x009c, PIN_OUTPUT, 2) /* (AG16)
>> PRG2_PRU0_GPO9.PRG2_RGMII1_TD1 */
>> + AM65X_IOPAD(0x00a0, PIN_OUTPUT, 2) /* (AF16)
>> PRG2_PRU0_GPO10.PRG2_RGMII1_TD2 */
>> + AM65X_IOPAD(0x00a4, PIN_OUTPUT, 2) /* (AE16)
>> PRG2_PRU0_GPO11.PRG2_RGMII1_TD3 */
>> + AM65X_IOPAD(0x00a8, PIN_INPUT, 2) /* (AD16)
>> PRG2_PRU0_GPO16.PRG2_RGMII1_TXC */
>> + AM65X_IOPAD(0x0090, PIN_OUTPUT, 2) /* (AE17)
>> PRG2_PRU0_GPO6.PRG2_RGMII1_TX_CTL */
>> + AM65X_IOPAD(0x008c, PIN_INPUT, 2) /* (AF17)
>> PRG2_PRU0_GPO5.PRG2_RGMII1_RXC */
>> + AM65X_IOPAD(0x0088, PIN_INPUT, 2) /* (AG17)
>> PRG2_PRU0_GPO4.PRG2_RGMII1_RX_CTL */
>> + >;
>> + };
>> };
>> &main_pmx1 {
>> @@ -621,3 +726,21 @@ &cpsw_port1 {
>> &dss {
>> status = "disabled";
>> };
>> +
>> +&icssg2_mdio {
>> + status = "okay";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&icssg2_mdio_pins_default>;
>> +
>> + icssg2_phy0: ethernet-phy@0 {
>> + reg = <0>;
>> + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
>> + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
>> + };
>> +
>> + icssg2_phy1: ethernet-phy@3 {
>> + reg = <3>;
>> + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
>> + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
>> + };
>> +};
--
Thanks and Regards,
Danish