On 11/20/2017 10:47 AM, Andy Duan wrote:
> From: Richard Leitner <[email protected]> Sent: Monday, November 20, 2017 4:34 PM
>> To: [email protected]; Andy Duan <[email protected]>;
>> [email protected]
>> Cc: [email protected]; [email protected];
>> [email protected]
>> Subject: [PATCH v2 3/3] net: ethernet: fec: fix refclk enable for SMSC
>> LAN8710/20
>>
>> From: Richard Leitner <[email protected]>
>>
>> Some PHYs (for example the SMSC LAN8710/LAN8720) doesn't allow turning
>> the refclk on and off again during operation (according to their datasheet).
>> Nonetheless exactly this behaviour was introduced for power saving reasons
>> by commit e8fcfcd5684a ("net: fec: optimize the clock management to save
>> power").
>> Therefore after enabling the refclk we detect if an affected PHY is attached. If
>> so reset and initialize it again.
...
>> +static int fec_enet_clk_ref_enable_reset_phy_quirk(struct net_device
>> +*ndev) {
>> + struct phy_device *phy_dev = ndev->phydev;
>> + u32 real_phy_id;
>> + int ret;
>> +
>> + /* some PHYs need a reset after the refclk was enabled, so we
>> + * reset them here
>> + */
>> + if (!phy_dev)
>> + return 0;
>> + if (!phy_dev->drv)
>> + return 0;
>> + real_phy_id = phy_dev->drv->phy_id & phy_dev->drv->phy_id_mask;
>> + switch (real_phy_id) {
>> + case 0x0007c0f0: /* SMSC LAN8710/LAN8720 */
>
> Don't hard code here...
> I believe there have many other phys also do such operation, hardcode is unacceptable...
>
> And these code can be put into phy_device.c as common interface.
Ok. Thank you for the feedback.
So it would be fine to hardcode the affected phy_id's in a common
function in phy_device.c?
Another possible solution that came to my mind is to add a flag called
something like "PHY_RST_AFTER_CLK_EN" to the flags variable in struct
phy_driver. This flag could then be set in the smsc PHY driver for
affected PHYs.
Then instead of comparing the phy_id in the MAC driver this flag could
be checked:
if (phydev->drv->flags & PHY_RST_AFTER_CLK_EN) {
ret = fec_reset_phy(ndev);
...
}
Would checking the flag be OK in fec_main.c?
What would be the "better" approach?
>
>> + ret = fec_reset_phy(ndev);
>> + if (ret)
>> + return ret;
>> + ret = phy_init_hw(phy_dev);
>> + if (ret)
>> + return ret;
>> + }
>> + return 0;
>> +}
>> +
>> static int fec_enet_clk_enable(struct net_device *ndev, bool enable) {
>> struct fec_enet_private *fep = netdev_priv(ndev); @@ -1862,6
>> +1889,10 @@ static int fec_enet_clk_enable(struct net_device *ndev, bool
>> enable)
>> ret = clk_prepare_enable(fep->clk_ref);
>> if (ret)
>> goto failed_clk_ref;
>> +
>> + ret = fec_enet_clk_ref_enable_reset_phy_quirk(ndev);
>> + if (ret)
>> + netdev_warn(ndev, "Resetting PHY failed, connection
>> may be
>> +unstable\n");
>> } else {
>> clk_disable_unprepare(fep->clk_ahb);
>> clk_disable_unprepare(fep->clk_enet_out);
>> @@ -2860,11 +2891,17 @@ fec_enet_open(struct net_device *ndev)
>> if (ret)
>> goto err_enet_mii_probe;
>>
>> + /* as the PHY is connected now, trigger the reset quirk again */
>> + ret = fec_enet_clk_ref_enable_reset_phy_quirk(ndev);
>> + if (ret)
>> + netdev_warn(ndev, "Resetting PHY failed, connection may be
>> +unstable\n");
>> +
>> if (fep->quirks & FEC_QUIRK_ERR006687)
>> imx6q_cpuidle_fec_irqs_used();
>>
>> napi_enable(&fep->napi);
>> phy_start(ndev->phydev);
>> +
>
> No need blank line here...
>> netif_tx_start_all_queues(ndev);
>>
>> device_set_wakeup_enable(&ndev->dev, fep->wol_flag &
>> --
>> 2.11.0
From 1584577956622352442@xxx Mon Nov 20 09:48:19 +0000 2017
X-GM-THRID: 1584573446575200827
X-Gmail-Labels: Inbox,Category Forums,HistoricalUnread