This commit introduces Power over Data Line (PoDL) Power Source
Equipment (PSE) regulator nodes to the PRTT1C devicetree. The addition
of these nodes enables support for PoDL in PRTT1C devices, allowing
power delivery and data transmission over a single twisted pair.
The new PoDL PSE regulator nodes provide voltage capability information
of the current board design, which can be used as a hint for system
administrators when configuring and managing power settings. This
update enhances the versatility and simplifies the power management of
PRTT1C devices while ensuring compatibility with connected Powered
Devices (PDs).
After applying this patch, the power delivery can be controlled from
user space with a patched [1] ethtool version using the following commands:
ethtool --set-pse t1l2 podl-pse-admin-control enable
to enable power delivery, and
ethtool --show-pse t1l2
to display the PoDL PSE settings.
By integrating PoDL PSE support into the PRTT1C devicetree, users can
benefit from streamlined power and data connections in their
deployments, improving overall system efficiency and reducing cabling
complexity.
[1] https://lore.kernel.org/all/[email protected]/
Signed-off-by: Oleksij Rempel <[email protected]>
---
arch/arm/boot/dts/stm32mp151a-prtt1c.dts | 32 ++++++++++++++++++++++++
1 file changed, 32 insertions(+)
diff --git a/arch/arm/boot/dts/stm32mp151a-prtt1c.dts b/arch/arm/boot/dts/stm32mp151a-prtt1c.dts
index 58bb05a8c685..ca0d3329cfd7 100644
--- a/arch/arm/boot/dts/stm32mp151a-prtt1c.dts
+++ b/arch/arm/boot/dts/stm32mp151a-prtt1c.dts
@@ -23,6 +23,18 @@ clock_sja1105: clock-sja1105 {
clock-frequency = <25000000>;
};
+ pse_t1l1: ethernet-pse-1 {
+ compatible = "podl-pse-regulator";
+ pse-supply = <®_t1l1>;
+ #pse-cells = <0>;
+ };
+
+ pse_t1l2: ethernet-pse-2 {
+ compatible = "podl-pse-regulator";
+ pse-supply = <®_t1l2>;
+ #pse-cells = <0>;
+ };
+
mdio0: mdio {
compatible = "virtual,mdio-gpio";
#address-cells = <1>;
@@ -32,6 +44,24 @@ mdio0: mdio {
};
+ reg_t1l1: regulator-pse-t1l1 {
+ compatible = "regulator-fixed";
+ regulator-name = "pse-t1l1";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ gpio = <&gpiog 13 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_t1l2: regulator-pse-t1l2 {
+ compatible = "regulator-fixed";
+ regulator-name = "pse-t1l2";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ gpio = <&gpiog 14 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
wifi_pwrseq: wifi-pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&gpiod 8 GPIO_ACTIVE_LOW>;
@@ -92,6 +122,7 @@ t1l1_phy: ethernet-phy@7 {
reset-gpios = <&gpiog 12 GPIO_ACTIVE_LOW>;
reset-assert-us = <10>;
reset-deassert-us = <35>;
+ pses = <&pse_t1l1>;
};
/* TI DP83TD510E */
@@ -102,6 +133,7 @@ t1l2_phy: ethernet-phy@10 {
reset-gpios = <&gpiog 11 GPIO_ACTIVE_LOW>;
reset-assert-us = <10>;
reset-deassert-us = <35>;
+ pses = <&pse_t1l2>;
};
/* Micrel KSZ9031 */
--
2.30.2
Hi Oleksij
On 3/23/23 13:32, Oleksij Rempel wrote:
> This commit introduces Power over Data Line (PoDL) Power Source
> Equipment (PSE) regulator nodes to the PRTT1C devicetree. The addition
> of these nodes enables support for PoDL in PRTT1C devices, allowing
> power delivery and data transmission over a single twisted pair.
>
> The new PoDL PSE regulator nodes provide voltage capability information
> of the current board design, which can be used as a hint for system
> administrators when configuring and managing power settings. This
> update enhances the versatility and simplifies the power management of
> PRTT1C devices while ensuring compatibility with connected Powered
> Devices (PDs).
>
> After applying this patch, the power delivery can be controlled from
> user space with a patched [1] ethtool version using the following commands:
> ethtool --set-pse t1l2 podl-pse-admin-control enable
> to enable power delivery, and
> ethtool --show-pse t1l2
> to display the PoDL PSE settings.
>
> By integrating PoDL PSE support into the PRTT1C devicetree, users can
> benefit from streamlined power and data connections in their
> deployments, improving overall system efficiency and reducing cabling
> complexity.
>
> [1] https://lore.kernel.org/all/[email protected]/
>
> Signed-off-by: Oleksij Rempel <[email protected]>
> ---
Please, fix the introduction of those new yaml validation errors:
arch/arm/boot/dts/stm32mp151a-prtt1c.dtb: ethernet-pse-1: $nodename:0:
'ethernet-pse-1' does not match '^ethernet-pse(@.*)?$'
From schema:
/Documentation/devicetree/bindings/net/pse-pd/podl-pse-regulator.yaml
arch/arm/boot/dts/stm32mp151a-prtt1c.dtb: ethernet-pse-2: $nodename:0:
'ethernet-pse-2' does not match '^ethernet-pse(@.*)?$'
From schema:
/local/home/frq08678/STLINUX/kernel/my-kernel/stm32/Documentation/devicetree/bindings/net/pse-pd/podl-pse-regulator.yaml
Thanks
Alex
> arch/arm/boot/dts/stm32mp151a-prtt1c.dts | 32 ++++++++++++++++++++++++
> 1 file changed, 32 insertions(+)
>
> diff --git a/arch/arm/boot/dts/stm32mp151a-prtt1c.dts b/arch/arm/boot/dts/stm32mp151a-prtt1c.dts
> index 58bb05a8c685..ca0d3329cfd7 100644
> --- a/arch/arm/boot/dts/stm32mp151a-prtt1c.dts
> +++ b/arch/arm/boot/dts/stm32mp151a-prtt1c.dts
> @@ -23,6 +23,18 @@ clock_sja1105: clock-sja1105 {
> clock-frequency = <25000000>;
> };
>
> + pse_t1l1: ethernet-pse-1 {
> + compatible = "podl-pse-regulator";
> + pse-supply = <®_t1l1>;
> + #pse-cells = <0>;
> + };
> +
> + pse_t1l2: ethernet-pse-2 {
> + compatible = "podl-pse-regulator";
> + pse-supply = <®_t1l2>;
> + #pse-cells = <0>;
> + };
> +
> mdio0: mdio {
> compatible = "virtual,mdio-gpio";
> #address-cells = <1>;
> @@ -32,6 +44,24 @@ mdio0: mdio {
>
> };
>
> + reg_t1l1: regulator-pse-t1l1 {
> + compatible = "regulator-fixed";
> + regulator-name = "pse-t1l1";
> + regulator-min-microvolt = <12000000>;
> + regulator-max-microvolt = <12000000>;
> + gpio = <&gpiog 13 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + reg_t1l2: regulator-pse-t1l2 {
> + compatible = "regulator-fixed";
> + regulator-name = "pse-t1l2";
> + regulator-min-microvolt = <12000000>;
> + regulator-max-microvolt = <12000000>;
> + gpio = <&gpiog 14 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> wifi_pwrseq: wifi-pwrseq {
> compatible = "mmc-pwrseq-simple";
> reset-gpios = <&gpiod 8 GPIO_ACTIVE_LOW>;
> @@ -92,6 +122,7 @@ t1l1_phy: ethernet-phy@7 {
> reset-gpios = <&gpiog 12 GPIO_ACTIVE_LOW>;
> reset-assert-us = <10>;
> reset-deassert-us = <35>;
> + pses = <&pse_t1l1>;
> };
>
> /* TI DP83TD510E */
> @@ -102,6 +133,7 @@ t1l2_phy: ethernet-phy@10 {
> reset-gpios = <&gpiog 11 GPIO_ACTIVE_LOW>;
> reset-assert-us = <10>;
> reset-deassert-us = <35>;
> + pses = <&pse_t1l2>;
> };
>
> /* Micrel KSZ9031 */
On Tue, Mar 28, 2023 at 11:58:34AM +0200, Alexandre TORGUE wrote:
> Hi Oleksij
>
> On 3/23/23 13:32, Oleksij Rempel wrote:
> > This commit introduces Power over Data Line (PoDL) Power Source
> > Equipment (PSE) regulator nodes to the PRTT1C devicetree. The addition
> > of these nodes enables support for PoDL in PRTT1C devices, allowing
> > power delivery and data transmission over a single twisted pair.
> >
> > The new PoDL PSE regulator nodes provide voltage capability information
> > of the current board design, which can be used as a hint for system
> > administrators when configuring and managing power settings. This
> > update enhances the versatility and simplifies the power management of
> > PRTT1C devices while ensuring compatibility with connected Powered
> > Devices (PDs).
> >
> > After applying this patch, the power delivery can be controlled from
> > user space with a patched [1] ethtool version using the following commands:
> > ethtool --set-pse t1l2 podl-pse-admin-control enable
> > to enable power delivery, and
> > ethtool --show-pse t1l2
> > to display the PoDL PSE settings.
> >
> > By integrating PoDL PSE support into the PRTT1C devicetree, users can
> > benefit from streamlined power and data connections in their
> > deployments, improving overall system efficiency and reducing cabling
> > complexity.
> >
> > [1] https://lore.kernel.org/all/[email protected]/
> >
> > Signed-off-by: Oleksij Rempel <[email protected]>
> > ---
>
> Please, fix the introduction of those new yaml validation errors:
>
> arch/arm/boot/dts/stm32mp151a-prtt1c.dtb: ethernet-pse-1: $nodename:0:
> 'ethernet-pse-1' does not match '^ethernet-pse(@.*)?$'
> From schema:
> /Documentation/devicetree/bindings/net/pse-pd/podl-pse-regulator.yaml
> arch/arm/boot/dts/stm32mp151a-prtt1c.dtb: ethernet-pse-2: $nodename:0:
> 'ethernet-pse-2' does not match '^ethernet-pse(@.*)?$'
> From schema: /local/home/frq08678/STLINUX/kernel/my-kernel/stm32/Documentation/devicetree/bindings/net/pse-pd/podl-pse-regulator.yaml
Using ethernet-pse@1 will require to use "reg" or "ranges" properties.
Which makes no sense in this use case. I need to fix the schema instead by
allowing this patter with following regex: "^ethernet-pse(@.*|-[0-9a-f])*$"
Should I send schema fix together with this patch?
Regards,
Oleksij
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
Hi Oleksij
On 3/28/23 13:02, Oleksij Rempel wrote:
> On Tue, Mar 28, 2023 at 11:58:34AM +0200, Alexandre TORGUE wrote:
>> Hi Oleksij
>>
>> On 3/23/23 13:32, Oleksij Rempel wrote:
>>> This commit introduces Power over Data Line (PoDL) Power Source
>>> Equipment (PSE) regulator nodes to the PRTT1C devicetree. The addition
>>> of these nodes enables support for PoDL in PRTT1C devices, allowing
>>> power delivery and data transmission over a single twisted pair.
>>>
>>> The new PoDL PSE regulator nodes provide voltage capability information
>>> of the current board design, which can be used as a hint for system
>>> administrators when configuring and managing power settings. This
>>> update enhances the versatility and simplifies the power management of
>>> PRTT1C devices while ensuring compatibility with connected Powered
>>> Devices (PDs).
>>>
>>> After applying this patch, the power delivery can be controlled from
>>> user space with a patched [1] ethtool version using the following commands:
>>> ethtool --set-pse t1l2 podl-pse-admin-control enable
>>> to enable power delivery, and
>>> ethtool --show-pse t1l2
>>> to display the PoDL PSE settings.
>>>
>>> By integrating PoDL PSE support into the PRTT1C devicetree, users can
>>> benefit from streamlined power and data connections in their
>>> deployments, improving overall system efficiency and reducing cabling
>>> complexity.
>>>
>>> [1] https://lore.kernel.org/all/[email protected]/
>>>
>>> Signed-off-by: Oleksij Rempel <[email protected]>
>>> ---
>>
>> Please, fix the introduction of those new yaml validation errors:
>>
>> arch/arm/boot/dts/stm32mp151a-prtt1c.dtb: ethernet-pse-1: $nodename:0:
>> 'ethernet-pse-1' does not match '^ethernet-pse(@.*)?$'
>> From schema:
>> /Documentation/devicetree/bindings/net/pse-pd/podl-pse-regulator.yaml
>> arch/arm/boot/dts/stm32mp151a-prtt1c.dtb: ethernet-pse-2: $nodename:0:
>> 'ethernet-pse-2' does not match '^ethernet-pse(@.*)?$'
>> From schema: /local/home/frq08678/STLINUX/kernel/my-kernel/stm32/Documentation/devicetree/bindings/net/pse-pd/podl-pse-regulator.yaml
>
> Using ethernet-pse@1 will require to use "reg" or "ranges" properties.
> Which makes no sense in this use case. I need to fix the schema instead by
> allowing this patter with following regex: "^ethernet-pse(@.*|-[0-9a-f])*$"
>
> Should I send schema fix together with this patch?
Yes you can. As soon as Rob or Krzysztof review it I'll apply both on
stm32-next.
Thanks
Alex
> Regards,
> Oleksij
Hi Oleksij
On 3/23/23 13:32, Oleksij Rempel wrote:
> This commit introduces Power over Data Line (PoDL) Power Source
> Equipment (PSE) regulator nodes to the PRTT1C devicetree. The addition
> of these nodes enables support for PoDL in PRTT1C devices, allowing
> power delivery and data transmission over a single twisted pair.
>
> The new PoDL PSE regulator nodes provide voltage capability information
> of the current board design, which can be used as a hint for system
> administrators when configuring and managing power settings. This
> update enhances the versatility and simplifies the power management of
> PRTT1C devices while ensuring compatibility with connected Powered
> Devices (PDs).
>
> After applying this patch, the power delivery can be controlled from
> user space with a patched [1] ethtool version using the following commands:
> ethtool --set-pse t1l2 podl-pse-admin-control enable
> to enable power delivery, and
> ethtool --show-pse t1l2
> to display the PoDL PSE settings.
>
> By integrating PoDL PSE support into the PRTT1C devicetree, users can
> benefit from streamlined power and data connections in their
> deployments, improving overall system efficiency and reducing cabling
> complexity.
>
> [1] https://lore.kernel.org/all/[email protected]/
>
> Signed-off-by: Oleksij Rempel <[email protected]>
> ---
Applied on stm32-next.
cheers
Alex