data field points to m41t00, instead it should point to m41t0.
Driver works correctly because on both cases(m41t0 and m41t00) chip_desc
are equal.
Point to right enum m41t0 instead of m41t00.
Signed-off-by: Giulio Benetti <[email protected]>
---
drivers/rtc/rtc-ds1307.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/rtc/rtc-ds1307.c b/drivers/rtc/rtc-ds1307.c
index a13e59edff53..32aadcbc377f 100644
--- a/drivers/rtc/rtc-ds1307.c
+++ b/drivers/rtc/rtc-ds1307.c
@@ -298,7 +298,7 @@ static const struct of_device_id ds1307_of_match[] = {
},
{
.compatible = "st,m41t0",
- .data = (void *)m41t00
+ .data = (void *)m41t0
},
{
.compatible = "st,m41t00",
--
2.17.0
The m41t11 variant is very similar to the already supported m41t00 and
m41t0, but it has also 56 bytes of NVRAM.
Add it to driver taking into account NVRAM section.
Signed-off-by: Giulio Benetti <[email protected]>
---
.../devicetree/bindings/rtc/rtc-ds1307.txt | 1 +
drivers/rtc/rtc-ds1307.c | 14 ++++++++++++++
2 files changed, 15 insertions(+)
diff --git a/Documentation/devicetree/bindings/rtc/rtc-ds1307.txt b/Documentation/devicetree/bindings/rtc/rtc-ds1307.txt
index d28d6e7f6ae8..ce6469c1a516 100644
--- a/Documentation/devicetree/bindings/rtc/rtc-ds1307.txt
+++ b/Documentation/devicetree/bindings/rtc/rtc-ds1307.txt
@@ -13,6 +13,7 @@ Required properties:
"maxim,ds3231",
"st,m41t0",
"st,m41t00",
+ "st,m41t11",
"microchip,mcp7940x",
"microchip,mcp7941x",
"pericom,pt7c4338",
diff --git a/drivers/rtc/rtc-ds1307.c b/drivers/rtc/rtc-ds1307.c
index 32aadcbc377f..0ab0c166da83 100644
--- a/drivers/rtc/rtc-ds1307.c
+++ b/drivers/rtc/rtc-ds1307.c
@@ -44,6 +44,7 @@ enum ds_type {
ds_3231,
m41t0,
m41t00,
+ m41t11,
mcp794xx,
rx_8025,
rx_8130,
@@ -226,6 +227,11 @@ static const struct chip_desc chips[last_ds_type] = {
.irq_handler = rx8130_irq,
.rtc_ops = &rx8130_rtc_ops,
},
+ [m41t11] = {
+ /* this is battery backed SRAM */
+ .nvram_offset = 8,
+ .nvram_size = 56,
+ },
[mcp794xx] = {
.alarm = 1,
/* this is battery backed SRAM */
@@ -248,6 +254,7 @@ static const struct i2c_device_id ds1307_id[] = {
{ "ds3231", ds_3231 },
{ "m41t0", m41t0 },
{ "m41t00", m41t00 },
+ { "m41t11", m41t11 },
{ "mcp7940x", mcp794xx },
{ "mcp7941x", mcp794xx },
{ "pt7c4338", ds_1307 },
@@ -304,6 +311,10 @@ static const struct of_device_id ds1307_of_match[] = {
.compatible = "st,m41t00",
.data = (void *)m41t00
},
+ {
+ .compatible = "st,m41t11",
+ .data = (void *)m41t11
+ },
{
.compatible = "microchip,mcp7940x",
.data = (void *)mcp794xx
@@ -346,6 +357,7 @@ static const struct acpi_device_id ds1307_acpi_ids[] = {
{ .id = "DS3231", .driver_data = ds_3231 },
{ .id = "M41T0", .driver_data = m41t0 },
{ .id = "M41T00", .driver_data = m41t00 },
+ { .id = "M41T11", .driver_data = m41t11 },
{ .id = "MCP7940X", .driver_data = mcp794xx },
{ .id = "MCP7941X", .driver_data = mcp794xx },
{ .id = "PT7C4338", .driver_data = ds_1307 },
@@ -1574,6 +1586,7 @@ static int ds1307_probe(struct i2c_client *client,
case ds_1307:
case m41t0:
case m41t00:
+ case m41t11:
/* clock halted? turn it on, so clock can tick. */
if (tmp & DS1307_BIT_CH) {
regmap_write(ds1307->regmap, DS1307_REG_SECS, 0);
@@ -1639,6 +1652,7 @@ static int ds1307_probe(struct i2c_client *client,
case ds_1340:
case m41t0:
case m41t00:
+ case m41t11:
/*
* NOTE: ignores century bits; fix before deploying
* systems that will run through year 2100.
--
2.17.0
m41txx chips can hold a calibration value to get correct clock bias.
Add offset handling (ranging between -63ppm and 126ppm) via sysfs.
Signed-off-by: Giulio Benetti <[email protected]>
---
V3 => V4:
* use ppm as offset input according to documentation instead of
raw ic offset values.
* use regmap_update_bits instead of regmap_write to update ic registers
* sysfs_remove_group if devm_add_action_or_reset fails
* rtc_device_unregister if ds1307_add_frequency_test fails on m41txx
series
drivers/rtc/rtc-ds1307.c | 81 ++++++++++++++++++++++++++++++++++++++++
1 file changed, 81 insertions(+)
diff --git a/drivers/rtc/rtc-ds1307.c b/drivers/rtc/rtc-ds1307.c
index 0ab0c166da83..2797d01bfa1d 100644
--- a/drivers/rtc/rtc-ds1307.c
+++ b/drivers/rtc/rtc-ds1307.c
@@ -114,6 +114,20 @@ enum ds_type {
# define RX8025_BIT_VDET 0x40
# define RX8025_BIT_XST 0x20
+#define M41TXX_REG_CONTROL 0x07
+# define M41TXX_BIT_OUT 0x80
+# define M41TXX_BIT_FT 0x40
+# define M41TXX_BIT_CALIB_SIGN 0x20
+# define M41TXX_M_CALIBRATION 0x1f
+
+/* negative offset step is -2.034ppm */
+#define M41TXX_NEG_OFFSET_STEP_PPM 2034
+/* positive offset step is +4.068ppm */
+#define M41TXX_POS_OFFSET_STEP_PPM 4068
+/* Min and max values supported with 'offset' interface by M41TXX */
+#define M41TXX_MIN_OFFSET (((-31) * M41TXX_NEG_OFFSET_STEP_PPM) / 1000)
+#define M41TXX_MAX_OFFSET (((31) * M41TXX_POS_OFFSET_STEP_PPM) / 1000)
+
struct ds1307 {
enum ds_type type;
unsigned long flags;
@@ -146,6 +160,9 @@ struct chip_desc {
static int ds1307_get_time(struct device *dev, struct rtc_time *t);
static int ds1307_set_time(struct device *dev, struct rtc_time *t);
+static int ds1337_read_alarm(struct device *dev, struct rtc_wkalrm *t);
+static int ds1337_set_alarm(struct device *dev, struct rtc_wkalrm *t);
+static int ds1307_alarm_irq_enable(struct device *dev, unsigned int enabled);
static u8 do_trickle_setup_ds1339(struct ds1307 *, u32 ohms, bool diode);
static irqreturn_t rx8130_irq(int irq, void *dev_id);
static int rx8130_read_alarm(struct device *dev, struct rtc_wkalrm *t);
@@ -155,6 +172,8 @@ static irqreturn_t mcp794xx_irq(int irq, void *dev_id);
static int mcp794xx_read_alarm(struct device *dev, struct rtc_wkalrm *t);
static int mcp794xx_set_alarm(struct device *dev, struct rtc_wkalrm *t);
static int mcp794xx_alarm_irq_enable(struct device *dev, unsigned int enabled);
+static int m41txx_rtc_read_offset(struct device *dev, long *offset);
+static int m41txx_rtc_set_offset(struct device *dev, long offset);
static const struct rtc_class_ops rx8130_rtc_ops = {
.read_time = ds1307_get_time,
@@ -172,6 +191,16 @@ static const struct rtc_class_ops mcp794xx_rtc_ops = {
.alarm_irq_enable = mcp794xx_alarm_irq_enable,
};
+static const struct rtc_class_ops m41txx_rtc_ops = {
+ .read_time = ds1307_get_time,
+ .set_time = ds1307_set_time,
+ .read_alarm = ds1337_read_alarm,
+ .set_alarm = ds1337_set_alarm,
+ .alarm_irq_enable = ds1307_alarm_irq_enable,
+ .read_offset = m41txx_rtc_read_offset,
+ .set_offset = m41txx_rtc_set_offset,
+};
+
static const struct chip_desc chips[last_ds_type] = {
[ds_1307] = {
.nvram_offset = 8,
@@ -227,10 +256,17 @@ static const struct chip_desc chips[last_ds_type] = {
.irq_handler = rx8130_irq,
.rtc_ops = &rx8130_rtc_ops,
},
+ [m41t0] = {
+ .rtc_ops = &m41txx_rtc_ops,
+ },
+ [m41t00] = {
+ .rtc_ops = &m41txx_rtc_ops,
+ },
[m41t11] = {
/* this is battery backed SRAM */
.nvram_offset = 8,
.nvram_size = 56,
+ .rtc_ops = &m41txx_rtc_ops,
},
[mcp794xx] = {
.alarm = 1,
@@ -972,6 +1008,51 @@ static int mcp794xx_alarm_irq_enable(struct device *dev, unsigned int enabled)
enabled ? MCP794XX_BIT_ALM0_EN : 0);
}
+static int m41txx_rtc_read_offset(struct device *dev, long *offset)
+{
+ struct ds1307 *ds1307 = dev_get_drvdata(dev);
+ unsigned int ctrl_reg;
+ u8 val;
+
+ regmap_read(ds1307->regmap, M41TXX_REG_CONTROL, &ctrl_reg);
+
+ val = ctrl_reg & M41TXX_M_CALIBRATION;
+
+ /* check if positive */
+ if (ctrl_reg & M41TXX_BIT_CALIB_SIGN)
+ *offset = (val * M41TXX_POS_OFFSET_STEP_PPM);
+ else
+ *offset = -(val * M41TXX_NEG_OFFSET_STEP_PPM);
+
+ *offset = DIV_ROUND_CLOSEST(*offset, 1000);
+
+ return 0;
+}
+
+static int m41txx_rtc_set_offset(struct device *dev, long offset)
+{
+ struct ds1307 *ds1307 = dev_get_drvdata(dev);
+ unsigned int ctrl_reg;
+
+ if ((offset < M41TXX_MIN_OFFSET) || (offset > M41TXX_MAX_OFFSET))
+ return -ERANGE;
+
+ offset *= 1000;
+
+ if (offset >= 0) {
+ ctrl_reg = DIV_ROUND_CLOSEST(offset,
+ M41TXX_POS_OFFSET_STEP_PPM);
+ ctrl_reg |= M41TXX_BIT_CALIB_SIGN;
+ } else {
+ ctrl_reg = DIV_ROUND_CLOSEST(abs(offset),
+ M41TXX_NEG_OFFSET_STEP_PPM);
+ }
+
+ return regmap_update_bits(ds1307->regmap, M41TXX_REG_CONTROL,
+ M41TXX_M_CALIBRATION | M41TXX_BIT_CALIB_SIGN,
+ ctrl_reg);
+}
+
/*----------------------------------------------------------------------*/
static int ds1307_nvram_read(void *priv, unsigned int offset, void *val,
--
2.17.0
On m41txx you can enable open-drain OUT pin to check if offset is ok.
Enabling OUT pin with freq_test attribute, OUT pin will tick 512 times
faster than 1s tick base.
Enable or Disable FT bit on CONTROL register if freq_test is 1 or 0.
Signed-off-by: Giulio Benetti <[email protected]>
---
V3 => V4:
* change attribute from freq_test to frequency_test_enable
* use regmap_update_bits instead of regmap_write
drivers/rtc/rtc-ds1307.c | 99 ++++++++++++++++++++++++++++++++++++++++
1 file changed, 99 insertions(+)
diff --git a/drivers/rtc/rtc-ds1307.c b/drivers/rtc/rtc-ds1307.c
index 2797d01bfa1d..de98ddc39515 100644
--- a/drivers/rtc/rtc-ds1307.c
+++ b/drivers/rtc/rtc-ds1307.c
@@ -1053,6 +1053,99 @@ static int m41txx_rtc_set_offset(struct device *dev, long offset)
ctrl_reg);
}
+static ssize_t frequency_test_enable_store(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct ds1307 *ds1307 = dev_get_drvdata(dev);
+ unsigned long freq_test = 0;
+ int retval;
+
+ retval = kstrtoul(buf, 10, &freq_test);
+ if ((retval < 0) || (retval > 1)) {
+ dev_err(dev, "Failed to store RTC Frequency Test attribute\n");
+ return -EINVAL;
+ }
+
+ regmap_update_bits(ds1307->regmap, M41TXX_REG_CONTROL, M41TXX_BIT_FT,
+ freq_test ? M41TXX_BIT_FT : 0);
+
+ return retval ? retval : count;
+}
+
+static ssize_t frequency_test_enable_show(struct device *dev,
+ struct device_attribute *attr,
+ char *buf)
+{
+ struct ds1307 *ds1307 = dev_get_drvdata(dev);
+ int freq_test_en = 0;
+ unsigned int ctrl_reg;
+
+ regmap_read(ds1307->regmap, M41TXX_REG_CONTROL, &ctrl_reg);
+
+ if (ctrl_reg & M41TXX_BIT_FT)
+ freq_test_en = true;
+ else
+ freq_test_en = false;
+
+ return sprintf(buf, "%d\n", freq_test_en);
+}
+
+static DEVICE_ATTR_RW(frequency_test_enable);
+
+static struct attribute *rtc_freq_test_attrs[] = {
+ &dev_attr_frequency_test_enable.attr,
+ NULL,
+};
+
+static const struct attribute_group rtc_freq_test_attr_group = {
+ .attrs = rtc_freq_test_attrs,
+};
+
+static void rtc_calib_remove_sysfs_group(void *_dev)
+{
+ struct device *dev = _dev;
+
+ sysfs_remove_group(&dev->kobj, &rtc_freq_test_attr_group);
+}
+
+static int ds1307_add_frequency_test(struct ds1307 *ds1307)
+{
+ int err = 0;
+
+ switch (ds1307->type) {
+ case m41t0:
+ case m41t00:
+ case m41t11:
+ /* Export sysfs entries */
+ err = sysfs_create_group(&(ds1307->dev)->kobj,
+ &rtc_freq_test_attr_group);
+ if (err) {
+ dev_err(ds1307->dev,
+ "Failed to create sysfs group: %d\n",
+ err);
+ return err;
+ }
+
+ err = devm_add_action_or_reset(ds1307->dev,
+ rtc_calib_remove_sysfs_group,
+ ds1307->dev);
+ if (err) {
+ dev_err(ds1307->dev,
+ "Failed to add sysfs cleanup action: %d\n",
+ err);
+ sysfs_remove_group(&(ds1307->dev)->kobj,
+ &rtc_freq_test_attr_group);
+ return err;
+ }
+ break;
+ default:
+ break;
+ }
+
+ return err;
+}
+
/*----------------------------------------------------------------------*/
static int ds1307_nvram_read(void *priv, unsigned int offset, void *val,
@@ -1794,6 +1887,12 @@ static int ds1307_probe(struct i2c_client *client,
if (err)
return err;
+ err = ds1307_add_frequency_test(ds1307);
+ if (err) {
+ rtc_device_unregister(ds1307->rtc);
+ return err;
+ }
+
if (chip->nvram_size) {
struct nvmem_config nvmem_cfg = {
.name = "ds1307_nvram",
--
2.17.0
Oh, sorry, I've forgotten to reword commit log.
I follow with v5 patchset.
Sorry again.
Giulio
Il 16/05/2018 12:05, Giulio Benetti ha scritto:
> On m41txx you can enable open-drain OUT pin to check if offset is ok.
> Enabling OUT pin with freq_test attribute, OUT pin will tick 512 times
> faster than 1s tick base.
>
> Enable or Disable FT bit on CONTROL register if freq_test is 1 or 0.
>
> Signed-off-by: Giulio Benetti <[email protected]>
> ---
> V3 => V4:
> * change attribute from freq_test to frequency_test_enable
> * use regmap_update_bits instead of regmap_write
>
> drivers/rtc/rtc-ds1307.c | 99 ++++++++++++++++++++++++++++++++++++++++
> 1 file changed, 99 insertions(+)
>
> diff --git a/drivers/rtc/rtc-ds1307.c b/drivers/rtc/rtc-ds1307.c
> index 2797d01bfa1d..de98ddc39515 100644
> --- a/drivers/rtc/rtc-ds1307.c
> +++ b/drivers/rtc/rtc-ds1307.c
> @@ -1053,6 +1053,99 @@ static int m41txx_rtc_set_offset(struct device *dev, long offset)
> ctrl_reg);
> }
>
> +static ssize_t frequency_test_enable_store(struct device *dev,
> + struct device_attribute *attr,
> + const char *buf, size_t count)
> +{
> + struct ds1307 *ds1307 = dev_get_drvdata(dev);
> + unsigned long freq_test = 0;
> + int retval;
> +
> + retval = kstrtoul(buf, 10, &freq_test);
> + if ((retval < 0) || (retval > 1)) {
> + dev_err(dev, "Failed to store RTC Frequency Test attribute\n");
> + return -EINVAL;
> + }
> +
> + regmap_update_bits(ds1307->regmap, M41TXX_REG_CONTROL, M41TXX_BIT_FT,
> + freq_test ? M41TXX_BIT_FT : 0);
> +
> + return retval ? retval : count;
> +}
> +
> +static ssize_t frequency_test_enable_show(struct device *dev,
> + struct device_attribute *attr,
> + char *buf)
> +{
> + struct ds1307 *ds1307 = dev_get_drvdata(dev);
> + int freq_test_en = 0;
> + unsigned int ctrl_reg;
> +
> + regmap_read(ds1307->regmap, M41TXX_REG_CONTROL, &ctrl_reg);
> +
> + if (ctrl_reg & M41TXX_BIT_FT)
> + freq_test_en = true;
> + else
> + freq_test_en = false;
> +
> + return sprintf(buf, "%d\n", freq_test_en);
> +}
> +
> +static DEVICE_ATTR_RW(frequency_test_enable);
> +
> +static struct attribute *rtc_freq_test_attrs[] = {
> + &dev_attr_frequency_test_enable.attr,
> + NULL,
> +};
> +
> +static const struct attribute_group rtc_freq_test_attr_group = {
> + .attrs = rtc_freq_test_attrs,
> +};
> +
> +static void rtc_calib_remove_sysfs_group(void *_dev)
> +{
> + struct device *dev = _dev;
> +
> + sysfs_remove_group(&dev->kobj, &rtc_freq_test_attr_group);
> +}
> +
> +static int ds1307_add_frequency_test(struct ds1307 *ds1307)
> +{
> + int err = 0;
> +
> + switch (ds1307->type) {
> + case m41t0:
> + case m41t00:
> + case m41t11:
> + /* Export sysfs entries */
> + err = sysfs_create_group(&(ds1307->dev)->kobj,
> + &rtc_freq_test_attr_group);
> + if (err) {
> + dev_err(ds1307->dev,
> + "Failed to create sysfs group: %d\n",
> + err);
> + return err;
> + }
> +
> + err = devm_add_action_or_reset(ds1307->dev,
> + rtc_calib_remove_sysfs_group,
> + ds1307->dev);
> + if (err) {
> + dev_err(ds1307->dev,
> + "Failed to add sysfs cleanup action: %d\n",
> + err);
> + sysfs_remove_group(&(ds1307->dev)->kobj,
> + &rtc_freq_test_attr_group);
> + return err;
> + }
> + break;
> + default:
> + break;
> + }
> +
> + return err;
> +}
> +
> /*----------------------------------------------------------------------*/
>
> static int ds1307_nvram_read(void *priv, unsigned int offset, void *val,
> @@ -1794,6 +1887,12 @@ static int ds1307_probe(struct i2c_client *client,
> if (err)
> return err;
>
> + err = ds1307_add_frequency_test(ds1307);
> + if (err) {
> + rtc_device_unregister(ds1307->rtc);
> + return err;
> + }
> +
> if (chip->nvram_size) {
> struct nvmem_config nvmem_cfg = {
> .name = "ds1307_nvram",
>