Dear Linux folks,
I suspended a Dell XPS 13 9360 with no devices attached into ACPI S3.
Then connecting an LMP USB-C mini Dock (P/N 15954) [1] with an Ethernet
cable attached to the left USB-C port and resumed the system from ACPI
S3. It took 37 seconds, until the link was established.
```
[ 0.000000] Linux version 6.8.0-rc5+
([email protected]) (gcc (Debian 13.2.0-13) 13.2.0,
GNU ld (GNU Binutils for Debian) 2.42) #27 SMP PREEMPT_DYNAMIC Wed Feb
21 09:09:49 CET 2024
[ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-6.8.0-rc5+
root=UUID=32e29882-d94d-4a92-9ee4-4d03002bfa29 ro quiet pci=noaer
mem_sleep_default=deep log_buf_len=8M cryptomgr.notests usbcore.dyndbg=+p
[…]
[ 0.000000] DMI: Dell Inc. XPS 13 9360/0596KF, BIOS 2.21.0 06/02/2022
[…]
[135623.339094] PM: suspend entry (deep)
[135623.345592] Filesystems sync: 0.006 seconds
[135623.349062] Freezing user space processes
[135623.352053] Freezing user space processes completed (elapsed 0.002
seconds)
[135623.352068] OOM killer disabled.
[135623.352071] Freezing remaining freezable tasks
[135623.353870] Freezing remaining freezable tasks completed (elapsed
0.001 seconds)
[135623.353985] printk: Suspending console(s) (use no_console_suspend to
debug)
[134781.473459] xhci_hcd 0000:00:14.0: hcd_pci_runtime_resume: 0
[134781.473482] usb usb1: usb auto-resume
[134781.473509] usb usb2: usb auto-resume
[134781.473517] hub 1-0:1.0: hub_resume
[134781.473540] hub 2-0:1.0: hub_resume
[134781.473597] usb usb1-port3: status 0107 change 0000
[134781.473616] usb usb1-port4: status 0107 change 0000
[134781.473632] usb usb1-port5: status 0507 change 0000
[134781.505615] hub 2-0:1.0: hub_suspend
[134781.505712] usb usb2: bus suspend, wakeup 0
[134781.521037] usb 1-4: usb auto-resume
[134781.589048] usb 1-4: Waited 0ms for CONNECT
[134781.589071] usb 1-4: finish resume
[134781.589879] usb 1-4: usb suspend, wakeup 0
[134781.589992] hub 1-0:1.0: hub_suspend
[134781.590103] usb usb1: bus suspend, wakeup 0
[134781.999962] ACPI: EC: interrupt blocked
[134782.002105] xhci_hcd 0000:00:14.0: wakeup: 1
[134782.033016] xhci_hcd 0000:00:14.0: --> PCI D3hot
[134782.033126] ACPI: PM: Preparing to enter system sleep state S3
[134782.049143] ACPI: EC: event blocked
[134782.049148] ACPI: EC: EC stopped
[134782.049150] ACPI: PM: Saving platform NVS memory
[134782.052592] Disabling non-boot CPUs ...
[134782.056035] smpboot: CPU 1 is now offline
[134782.060287] smpboot: CPU 2 is now offline
[134782.063001] smpboot: CPU 3 is now offline
[134782.072093] ACPI: PM: Low-level resume complete
[134782.072137] ACPI: EC: EC started
[134782.072138] ACPI: PM: Restoring platform NVS memory
[134782.074101] Enabling non-boot CPUs ...
[134782.074126] smpboot: Booting Node 0 Processor 1 APIC 0x2
[134782.074972] CPU1 is up
[134782.074989] smpboot: Booting Node 0 Processor 2 APIC 0x1
[134782.075759] CPU2 is up
[134782.075776] smpboot: Booting Node 0 Processor 3 APIC 0x3
[134782.076474] CPU3 is up
[134782.079463] ACPI: PM: Waking up from system sleep state S3
[134782.126767] ACPI: EC: interrupt unblocked
[134782.161453] ACPI: EC: event unblocked
[134782.164047] usb usb1: usb resume
[134782.164088] usb usb2: usb resume
[134782.164127] hub 2-0:1.0: hub_resume
[134782.164970] i915 0000:00:02.0: [drm] [ENCODER:94:DDI A/PHY A] is
disabled/in DSI mode with an ungated DDI clock, gate it
[134782.164981] i915 0000:00:02.0: [drm] [ENCODER:102:DDI B/PHY B] is
disabled/in DSI mode with an ungated DDI clock, gate it
[134782.164989] i915 0000:00:02.0: [drm] [ENCODER:113:DDI C/PHY C] is
disabled/in DSI mode with an ungated DDI clock, gate it
[134782.174398] nvme nvme0: 4/0/0 default/read/poll queues
[134782.175094] hub 1-0:1.0: hub_resume
[134782.175153] usb usb1-port3: status 0101 change 0001
[134782.175176] usb usb1-port4: status 0101 change 0001
[134782.175195] usb usb1-port5: status 0101 change 0001
[134782.299331] usb 1-3: Waited 0ms for CONNECT
[134782.299336] usb 1-5: Waited 0ms for CONNECT
[134782.299339] usb 1-3: finish reset-resume
[134782.299343] usb 1-5: finish reset-resume
[134782.303359] usb 1-4: Waited 0ms for CONNECT
[134782.303363] usb 1-4: finish reset-resume
[134782.411326] atkbd serio0: Failed to deactivate keyboard on
isa0060/serio0
[134782.427585] usb 1-3: reset full-speed USB device number 2 using xhci_hcd
[134782.703558] usb 1-5: reset high-speed USB device number 4 using xhci_hcd
[134782.979518] usb 1-4: reset full-speed USB device number 3 using xhci_hcd
[134783.137568] OOM killer enabled.
[134783.137570] Restarting tasks ...
[134783.137607] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0000
[134783.138111] hub 2-0:1.0: hub_suspend
[134783.138130] usb usb2: bus auto-suspend, wakeup 1
[134783.139896] usb usb2: usb wakeup-resume
[134783.139903] usb usb2: usb auto-resume
[134783.141145] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0010
[134783.144869] done.
[134783.144884] random: crng reseeded on system resumption
[134783.155322] hub 2-0:1.0: hub_resume
[134783.187376] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0000
[134783.187433] hub 2-0:1.0: hub_suspend
[134783.187439] usb usb2: bus auto-suspend, wakeup 1
[134783.225883] PM: suspend exit
[134783.295100] Process accounting resumed
[134783.483053] mei_hdcp
0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0
(ops i915_hdcp_ops [i915])
[134785.095304] usb 1-3: usb auto-suspend, wakeup 0
[134785.439272] usb 1-5: usb auto-suspend, wakeup 0
[134785.583269] usb 1-4: usb auto-suspend, wakeup 1
[134785.603266] hub 1-0:1.0: hub_suspend
[134785.603280] usb usb1: bus auto-suspend, wakeup 1
[134785.603448] xhci_hcd 0000:00:14.0: hcd_pci_runtime_suspend: 0
[134788.708764] wlp58s0: authenticate with a4:97:33:06:77:d3 (local
address=9c:b6:d0:d1:6a:b1)
[134788.708770] wlp58s0: send auth to a4:97:33:06:77:d3 (try 1/3)
[134788.709809] wlp58s0: authenticated
[134788.711232] wlp58s0: associate with a4:97:33:06:77:d3 (try 1/3)
[134788.714287] wlp58s0: RX AssocResp from a4:97:33:06:77:d3
(capab=0x511 status=0 aid=102)
[134788.717462] wlp58s0: associated
[134788.721574] wlp58s0: Limiting TX power to 30 (30 - 0) dBm as
advertised by a4:97:33:06:77:d3
[135619.981952] xhci_hcd 0000:00:14.0: hcd_pci_runtime_resume: 0
[135619.982043] usb usb1: usb wakeup-resume
[135619.982048] usb usb1: usb auto-resume
[135619.982072] hub 1-0:1.0: hub_resume
[135619.982103] usb usb1-port3: status 0107 change 0000
[135619.982111] usb usb1-port4: status 0107 change 0000
[135619.982119] usb usb1-port5: status 0507 change 0000
[135619.982163] usb usb2: usb wakeup-resume
[135619.982165] usb usb2: usb auto-resume
[135619.982188] hub 2-0:1.0: hub_resume
[135619.982198] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0000
[135619.987438] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0000
[135620.009646] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0000
[135620.009700] hub 2-0:1.0: hub_suspend
[135620.009705] usb usb2: bus auto-suspend, wakeup 1
[135620.148856] wlp58s0: deauthenticating from a4:97:33:06:77:d3 by
local choice (Reason: 3=DEAUTH_LEAVING)
[135620.157614] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0010
[135620.177775] usb 1-4: usb wakeup-resume
[135620.197833] usb 1-4: Waited 0ms for CONNECT
[135620.197838] usb 1-4: finish resume
[135620.198318] usb usb1-port4: resume, status 0
[135622.717569] usb 1-4: usb auto-suspend, wakeup 1
[135622.737533] hub 1-0:1.0: hub_suspend
[135622.737550] usb usb1: bus auto-suspend, wakeup 1
[135622.737701] xhci_hcd 0000:00:14.0: hcd_pci_runtime_suspend: 0
[135623.339094] PM: suspend entry (deep)
[135623.345592] Filesystems sync: 0.006 seconds
[135623.349062] Freezing user space processes
[135623.352053] Freezing user space processes completed (elapsed 0.002
seconds)
[135623.352068] OOM killer disabled.
[135623.352071] Freezing remaining freezable tasks
[135623.353870] Freezing remaining freezable tasks completed (elapsed
0.001 seconds)
[135623.353985] printk: Suspending console(s) (use no_console_suspend to
debug)
[135623.390281] xhci_hcd 0000:00:14.0: hcd_pci_runtime_resume: 0
[135623.390306] usb usb1: usb auto-resume
[135623.390319] usb usb2: usb auto-resume
[135623.390340] hub 1-0:1.0: hub_resume
[135623.390358] hub 2-0:1.0: hub_resume
[135623.390535] usb usb1-port3: status 0107 change 0000
[135623.390593] usb usb1-port4: status 0107 change 0000
[135623.390671] usb usb1-port5: status 0507 change 0000
[135623.417795] hub 2-0:1.0: hub_suspend
[135623.417832] usb usb2: bus suspend, wakeup 0
[135623.437691] usb 1-4: usb auto-resume
[135623.505705] usb 1-4: Waited 0ms for CONNECT
[135623.505722] usb 1-4: finish resume
[135623.506183] usb 1-4: usb suspend, wakeup 0
[135623.506226] hub 1-0:1.0: hub_suspend
[135623.506285] usb usb1: bus suspend, wakeup 0
[135623.918326] ACPI: EC: interrupt blocked
[135623.922119] xhci_hcd 0000:00:14.0: wakeup: 1
[135623.953670] xhci_hcd 0000:00:14.0: --> PCI D3hot
[135623.953772] ACPI: PM: Preparing to enter system sleep state S3
[135623.963290] ACPI: EC: event blocked
[135623.963291] ACPI: EC: EC stopped
[135623.963292] ACPI: PM: Saving platform NVS memory
[135623.964787] Disabling non-boot CPUs ...
[135623.966332] smpboot: CPU 1 is now offline
[135623.968749] smpboot: CPU 2 is now offline
[135623.970630] smpboot: CPU 3 is now offline
[135623.975734] ACPI: PM: Low-level resume complete
[135623.975778] ACPI: EC: EC started
[135623.975779] ACPI: PM: Restoring platform NVS memory
[135623.977741] Enabling non-boot CPUs ...
[135623.977767] smpboot: Booting Node 0 Processor 1 APIC 0x2
[135623.978525] CPU1 is up
[135623.978542] smpboot: Booting Node 0 Processor 2 APIC 0x1
[135623.979283] CPU2 is up
[135623.979299] smpboot: Booting Node 0 Processor 3 APIC 0x3
[135623.979965] CPU3 is up
[135623.982953] ACPI: PM: Waking up from system sleep state S3
[135628.953183] ACPI: EC: interrupt unblocked
[135629.001792] ACPI: EC: event unblocked
[135629.004635] usb usb1: usb resume
[135629.004637] usb usb2: usb resume
[135629.004658] hub 2-0:1.0: hub_resume
[135629.005256] i915 0000:00:02.0: [drm] [ENCODER:94:DDI A/PHY A] is
disabled/in DSI mode with an ungated DDI clock, gate it
[135629.005261] i915 0000:00:02.0: [drm] [ENCODER:102:DDI B/PHY B] is
disabled/in DSI mode with an ungated DDI clock, gate it
[135629.005264] i915 0000:00:02.0: [drm] [ENCODER:113:DDI C/PHY C] is
disabled/in DSI mode with an ungated DDI clock, gate it
[135629.014542] nvme nvme0: 4/0/0 default/read/poll queues
[135629.015207] hub 1-0:1.0: hub_resume
[135629.015226] usb usb1-port3: status 0101 change 0001
[135629.015235] usb usb1-port4: status 0101 change 0001
[135629.015243] usb usb1-port5: status 0101 change 0001
[135629.139830] usb 1-5: Waited 0ms for CONNECT
[135629.139834] usb 1-5: finish reset-resume
[135629.139836] usb 1-3: Waited 0ms for CONNECT
[135629.139838] usb 1-3: finish reset-resume
[135629.139876] usb 1-4: Waited 0ms for CONNECT
[135629.139879] usb 1-4: finish reset-resume
[135629.268021] usb 1-5: reset high-speed USB device number 4 using xhci_hcd
[135629.544069] usb 1-3: reset full-speed USB device number 2 using xhci_hcd
[135629.820015] usb 1-4: reset full-speed USB device number 3 using xhci_hcd
[135629.976929] mei_hdcp
0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0
(ops i915_hdcp_ops [i915])
[135629.977326] OOM killer enabled.
[135629.977329] Restarting tasks ...
[135629.977351] pci 0000:01:00.0: [8086:1576] type 01 class 0x060400
PCIe Switch Upstream Port
[135629.977404] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0010
[135629.977405] pci 0000:01:00.0: PCI bridge to [bus 02-39]
[135629.977425] pci 0000:01:00.0: bridge window [mem
0xc4000000-0xda0fffff]
[135629.977446] pci 0000:01:00.0: bridge window [mem
0xa0000000-0xc1ffffff 64bit pref]
[135629.977475] pci 0000:01:00.0: enabling Extended Tags
[135629.977561] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0000
[135629.977886] pci 0000:01:00.0: supports D1 D2
[135629.977889] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[135629.977998] pci 0000:01:00.0: 15.752 Gb/s available PCIe bandwidth,
limited by 8.0 GT/s PCIe x2 link at 0000:00:1c.0 (capable of 31.504 Gb/s
with 8.0 GT/s PCIe x4 link)
[135629.981650] pci 0000:02:00.0: [8086:1576] type 01 class 0x060400
PCIe Switch Downstream Port
[135629.981716] pci 0000:02:00.0: PCI bridge to [bus 03]
[135629.981738] pci 0000:02:00.0: bridge window [mem
0xda000000-0xda0fffff]
[135629.981781] pci 0000:02:00.0: enabling Extended Tags
[135629.981937] pci 0000:02:00.0: supports D1 D2
[135629.981940] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[135629.982333] pci 0000:02:01.0: [8086:1576] type 01 class 0x060400
PCIe Switch Downstream Port
[135629.982387] pci 0000:02:01.0: PCI bridge to [bus 04-38]
[135629.982405] pci 0000:02:01.0: bridge window [mem
0xc4000000-0xd9efffff]
[135629.982426] pci 0000:02:01.0: bridge window [mem
0xa0000000-0xc1ffffff 64bit pref]
[135629.982450] pci 0000:02:01.0: enabling Extended Tags
[135629.982621] pci 0000:02:01.0: supports D1 D2
[135629.982624] pci 0000:02:01.0: PME# supported from D0 D1 D2 D3hot D3cold
[135629.983907] hub 2-0:1.0: hub_suspend
[135629.983945] usb usb2: bus auto-suspend, wakeup 1
[135629.984444] done.
[135629.984460] random: crng reseeded on system resumption
[135629.986390] pci 0000:02:02.0: [8086:1576] type 01 class 0x060400
PCIe Switch Downstream Port
[135629.986441] pci 0000:02:02.0: PCI bridge to [bus 39]
[135629.986458] pci 0000:02:02.0: bridge window [mem
0xd9f00000-0xd9ffffff]
[135629.986492] pci 0000:02:02.0: enabling Extended Tags
[135629.986629] pci 0000:02:02.0: supports D1 D2
[135629.986631] pci 0000:02:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[135629.986929] pci 0000:01:00.0: PCI bridge to [bus 02-39]
[135629.987022] pci 0000:02:00.0: PCI bridge to [bus 03]
[135629.987103] pci 0000:02:01.0: PCI bridge to [bus 04-38]
[135629.990420] pci 0000:39:00.0: [8086:15b5] type 00 class 0x0c0330
PCIe Endpoint
[135629.990454] pci 0000:39:00.0: BAR 0 [mem 0xd9f00000-0xd9f0ffff]
[135629.990554] pci 0000:39:00.0: enabling Extended Tags
[135629.997287] pci 0000:39:00.0: supports D1 D2
[135629.997295] pci 0000:39:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[135629.997443] pci 0000:39:00.0: 8.000 Gb/s available PCIe bandwidth,
limited by 2.5 GT/s PCIe x4 link at 0000:02:02.0 (capable of 31.504 Gb/s
with 8.0 GT/s PCIe x4 link)
[135629.997814] pci 0000:02:02.0: PCI bridge to [bus 39]
[135629.997867] pci_bus 0000:02: Allocating resources
[135629.997892] pci 0000:02:01.0: bridge window [io 0x1000-0x0fff] to
[bus 04-38] add_size 1000
[135629.997901] pci 0000:02:02.0: bridge window [io 0x1000-0x0fff] to
[bus 39] add_size 1000
[135629.997904] pci 0000:02:02.0: bridge window [mem
0x00100000-0x000fffff 64bit pref] to [bus 39] add_size 200000 add_align
100000
[135629.997908] pci 0000:01:00.0: bridge window [io 0x1000-0x0fff] to
[bus 02-39] add_size 2000
[135629.997912] pci 0000:01:00.0: bridge window [io size 0x2000]: can't
assign; no space
[135629.997915] pci 0000:01:00.0: bridge window [io size 0x2000]:
failed to assign
[135629.997917] pci 0000:01:00.0: bridge window [io size 0x2000]: can't
assign; no space
[135629.997924] pci 0000:01:00.0: bridge window [io size 0x2000]:
failed to assign
[135629.997929] pci 0000:02:02.0: bridge window [mem size 0x00200000
64bit pref]: can't assign; no space
[135629.997931] pci 0000:02:02.0: bridge window [mem size 0x00200000
64bit pref]: failed to assign
[135629.997932] pci 0000:02:01.0: bridge window [io size 0x1000]: can't
assign; no space
[135629.997934] pci 0000:02:01.0: bridge window [io size 0x1000]:
failed to assign
[135629.997935] pci 0000:02:02.0: bridge window [io size 0x1000]: can't
assign; no space
[135629.997937] pci 0000:02:02.0: bridge window [io size 0x1000]:
failed to assign
[135629.997940] pci 0000:02:02.0: bridge window [mem size 0x00200000
64bit pref]: can't assign; no space
[135629.997942] pci 0000:02:02.0: bridge window [mem size 0x00200000
64bit pref]: failed to assign
[135629.997982] pci 0000:02:02.0: bridge window [io size 0x1000]: can't
assign; no space
[135629.998009] pci 0000:02:02.0: bridge window [io size 0x1000]:
failed to assign
[135629.998037] pci 0000:02:01.0: bridge window [io size 0x1000]: can't
assign; no space
[135629.998063] pci 0000:02:01.0: bridge window [io size 0x1000]:
failed to assign
[135629.998125] pci 0000:02:00.0: PCI bridge to [bus 03]
[135629.998131] pci 0000:02:00.0: bridge window [mem
0xda000000-0xda0fffff]
[135629.998140] pci 0000:02:01.0: PCI bridge to [bus 04-38]
[135629.998145] pci 0000:02:01.0: bridge window [mem
0xc4000000-0xd9efffff]
[135629.998149] pci 0000:02:01.0: bridge window [mem
0xa0000000-0xc1ffffff 64bit pref]
[135629.998156] pci 0000:02:02.0: PCI bridge to [bus 39]
[135629.998161] pci 0000:02:02.0: bridge window [mem
0xd9f00000-0xd9ffffff]
[135629.998169] pci 0000:01:00.0: PCI bridge to [bus 02-39]
[135629.998175] pci 0000:01:00.0: bridge window [mem
0xc4000000-0xda0fffff]
[135629.998179] pci 0000:01:00.0: bridge window [mem
0xa0000000-0xc1ffffff 64bit pref]
[135630.003545] xhci_hcd 0000:39:00.0: xHCI Host Controller
[135630.003562] xhci_hcd 0000:39:00.0: new USB bus registered, assigned
bus number 3
[135630.004799] xhci_hcd 0000:39:00.0: hcc params 0x200077c1 hci version
0x110 quirks 0x0000000200009810
[135630.004875] xhci_hcd 0000:39:00.0: supports USB remote wakeup
[135630.024937] xhci_hcd 0000:39:00.0: xHCI Host Controller
[135630.024946] xhci_hcd 0000:39:00.0: new USB bus registered, assigned
bus number 4
[135630.024953] xhci_hcd 0000:39:00.0: Host supports USB 3.1 Enhanced
SuperSpeed
[135630.024956] xhci_hcd 0000:39:00.0: supports USB remote wakeup
[135630.025073] usb usb3: default language 0x0409
[135630.025089] usb usb3: udev 1, busnum 3, minor = 256
[135630.025092] usb usb3: New USB device found, idVendor=1d6b,
idProduct=0002, bcdDevice= 6.08
[135630.025095] usb usb3: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[135630.025097] usb usb3: Product: xHCI Host Controller
[135630.025099] usb usb3: Manufacturer: Linux 6.8.0-rc5+ xhci-hcd
[135630.025100] usb usb3: SerialNumber: 0000:39:00.0
[135630.076427] usb usb3: usb_probe_device
[135630.076432] usb usb3: configuration #1 chosen from 1 choice
[135630.076450] usb usb3: adding 3-0:1.0 (config #1, interface 0)
[135630.077078] hub 3-0:1.0: usb_probe_interface
[135630.077104] hub 3-0:1.0: usb_probe_interface - got id
[135630.077127] hub 3-0:1.0: USB hub found
[135630.077169] hub 3-0:1.0: 2 ports detected
[135630.077171] hub 3-0:1.0: standalone hub
[135630.077172] hub 3-0:1.0: no power switching (usb 1.0)
[135630.077174] hub 3-0:1.0: individual port over-current protection
[135630.077175] hub 3-0:1.0: Single TT
[135630.077176] hub 3-0:1.0: TT requires at most 8 FS bit times (666 ns)
[135630.077178] hub 3-0:1.0: power on to power good time: 20ms
[135630.077188] hub 3-0:1.0: local power source is good
[135630.078734] hub 3-0:1.0: trying to enable port power on
non-switchable hub
[135630.083747] usb usb4: skipped 1 descriptor after endpoint
[135630.083784] usb usb4: default language 0x0409
[135630.083877] usb usb4: udev 1, busnum 4, minor = 384
[135630.083890] usb usb4: New USB device found, idVendor=1d6b,
idProduct=0003, bcdDevice= 6.08
[135630.083904] usb usb4: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[135630.083913] usb usb4: Product: xHCI Host Controller
[135630.083921] usb usb4: Manufacturer: Linux 6.8.0-rc5+ xhci-hcd
[135630.083927] usb usb4: SerialNumber: 0000:39:00.0
[135630.091335] usb usb4: usb_probe_device
[135630.091350] usb usb4: configuration #1 chosen from 1 choice
[135630.091400] usb usb4: adding 4-0:1.0 (config #1, interface 0)
[135630.091503] hub 4-0:1.0: usb_probe_interface
[135630.091509] hub 4-0:1.0: usb_probe_interface - got id
[135630.091517] hub 4-0:1.0: USB hub found
[135630.091540] hub 4-0:1.0: 2 ports detected
[135630.091546] hub 4-0:1.0: standalone hub
[135630.091551] hub 4-0:1.0: no power switching (usb 1.0)
[135630.091556] hub 4-0:1.0: individual port over-current protection
[135630.091562] hub 4-0:1.0: TT requires at most 8 FS bit times (666 ns)
[135630.091568] hub 4-0:1.0: power on to power good time: 100ms
[135630.091590] hub 4-0:1.0: local power source is good
[135630.097020] usb usb4-port1: peered to usb3-port1
[135630.103851] usb usb3-port1: status 0101 change 0001
[135630.109207] usb usb4: port-1 no _DSM function 5
[135630.109224] usb usb4: port-2 no _DSM function 5
[135630.109230] hub 4-0:1.0: trying to enable port power on
non-switchable hub
[135630.110174] pci_bus 0000:02: Allocating resources
[135630.110197] pcieport 0000:02:01.0: bridge window [io 0x1000-0x0fff]
to [bus 04-38] add_size 1000
[135630.110205] pcieport 0000:02:02.0: bridge window [io 0x1000-0x0fff]
to [bus 39] add_size 1000
[135630.110210] pcieport 0000:02:02.0: bridge window [mem
0x00100000-0x000fffff 64bit pref] to [bus 39] add_size 200000 add_align
100000
[135630.110218] pcieport 0000:01:00.0: bridge window [io 0x1000-0x0fff]
to [bus 02-39] add_size 2000
[135630.110224] pcieport 0000:01:00.0: bridge window [io size 0x2000]:
can't assign; no space
[135630.110228] pcieport 0000:01:00.0: bridge window [io size 0x2000]:
failed to assign
[135630.110233] pcieport 0000:01:00.0: bridge window [io size 0x2000]:
can't assign; no space
[135630.110236] pcieport 0000:01:00.0: bridge window [io size 0x2000]:
failed to assign
[135630.110245] pcieport 0000:02:02.0: bridge window [mem size
0x00200000 64bit pref]: can't assign; no space
[135630.110249] pcieport 0000:02:02.0: bridge window [mem size
0x00200000 64bit pref]: failed to assign
[135630.110253] pcieport 0000:02:01.0: bridge window [io size 0x1000]:
can't assign; no space
[135630.110257] pcieport 0000:02:01.0: bridge window [io size 0x1000]:
failed to assign
[135630.110260] pcieport 0000:02:02.0: bridge window [io size 0x1000]:
can't assign; no space
[135630.110263] pcieport 0000:02:02.0: bridge window [io size 0x1000]:
failed to assign
[135630.110271] pcieport 0000:02:02.0: bridge window [mem size
0x00200000 64bit pref]: can't assign; no space
[135630.110275] pcieport 0000:02:02.0: bridge window [mem size
0x00200000 64bit pref]: failed to assign
[135630.110279] pcieport 0000:02:02.0: bridge window [io size 0x1000]:
can't assign; no space
[135630.110282] pcieport 0000:02:02.0: bridge window [io size 0x1000]:
failed to assign
[135630.110286] pcieport 0000:02:01.0: bridge window [io size 0x1000]:
can't assign; no space
[135630.110289] pcieport 0000:02:01.0: bridge window [io size 0x1000]:
failed to assign
[135630.139535] PM: suspend exit
[135630.211437] hub 3-0:1.0: state 7 ports 2 chg 0002 evt 0000
[135630.211534] usb usb3-port1: status 0101, change 0000, 12 Mb/s
[135630.211937] usb usb4-port1: status 0203 change 0011
[135630.293847] Process accounting resumed
[135630.319813] hub 4-0:1.0: state 7 ports 2 chg 0002 evt 0000
[135630.319836] usb usb4-port1: status 0203, change 0000, 10.0 Gb/s
[135630.339810] usb 3-1: new high-speed USB device number 2 using xhci_hcd
[135630.497568] usb 3-1: default language 0x0409
[135630.498182] usb 3-1: udev 2, busnum 3, minor = 257
[135630.498220] usb 3-1: New USB device found, idVendor=2109,
idProduct=2817, bcdDevice= 5.e3
[135630.498252] usb 3-1: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[135630.498254] usb 3-1: Product: USB2.0 Hub
[135630.498256] usb 3-1: Manufacturer: VIA Labs, Inc.
[135630.498258] usb 3-1: SerialNumber: 000000000
[135630.499087] usb 3-1: usb_probe_device
[135630.499101] usb 3-1: configuration #1 chosen from 1 choice
[135630.503960] usb 3-1: adding 3-1:1.0 (config #1, interface 0)
[135630.504782] hub 3-1:1.0: usb_probe_interface
[135630.504796] hub 3-1:1.0: usb_probe_interface - got id
[135630.504807] hub 3-1:1.0: USB hub found
[135630.505081] hub 3-1:1.0: 5 ports detected
[135630.505094] hub 3-1:1.0: standalone hub
[135630.505100] hub 3-1:1.0: individual port power switching
[135630.505107] hub 3-1:1.0: individual port over-current protection
[135630.509115] hub 3-1:1.0: TT per port
[135630.509124] hub 3-1:1.0: TT requires at most 32 FS bit times (2664 ns)
[135630.509130] hub 3-1:1.0: Port indicators are supported
[135630.509133] hub 3-1:1.0: power on to power good time: 350ms
[135630.511933] hub 3-1:1.0: local power source is good
[135630.531819] hub 3-1:1.0: enabling power on all ports
[135630.655107] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[135630.656725] usb 4-1: new SuperSpeed USB device number 2 using xhci_hcd
[135630.709274] usb 4-1: skipped 1 descriptor after endpoint
[135630.709452] usb 4-1: default language 0x0409
[135630.710095] usb 4-1: udev 2, busnum 4, minor = 385
[135630.710100] usb 4-1: New USB device found, idVendor=2109,
idProduct=0817, bcdDevice= 5.e3
[135630.710104] usb 4-1: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[135630.710107] usb 4-1: Product: USB3.0 Hub
[135630.710110] usb 4-1: Manufacturer: VIA Labs, Inc.
[135630.710112] usb 4-1: SerialNumber: 000000000
[135630.710623] usb 4-1: usb_probe_device
[135630.710629] usb 4-1: configuration #1 chosen from 1 choice
[135630.711774] usb 4-1: adding 4-1:1.0 (config #1, interface 0)
[135630.712044] hub 4-1:1.0: usb_probe_interface
[135630.712049] hub 4-1:1.0: usb_probe_interface - got id
[135630.712054] hub 4-1:1.0: USB hub found
[135630.715800] hub 4-1:1.0: 4 ports detected
[135630.715805] hub 4-1:1.0: standalone hub
[135630.715807] hub 4-1:1.0: individual port power switching
[135630.715809] hub 4-1:1.0: individual port over-current protection
[135630.715811] hub 4-1:1.0: TT requires at most 8 FS bit times (666 ns)
[135630.715813] hub 4-1:1.0: power on to power good time: 350ms
[135630.716557] hub 4-1:1.0: local power source is good
[135630.718147] usb 4-1-port1: peered to 3-1-port1
[135630.718183] usb 4-1-port2: peered to 3-1-port2
[135630.718212] usb 4-1-port3: peered to 3-1-port3
[135630.718233] usb 4-1-port4: peered to 3-1-port4
[135630.818907] hub 4-1:1.0: enabling power on all ports
[135630.819762] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
[135631.039821] usb 3-1-port1: status 0101 change 0001
[135631.040749] usb 3-1-port5: status 0501 change 0001
[135631.147824] hub 3-1:1.0: state 7 ports 5 chg 0022 evt 0000
[135631.148042] usb 3-1-port1: status 0101, change 0000, 12 Mb/s
[135631.148206] usb 3-1-port1: indicator auto status 0
[135631.198801] usb 4-1-port1: status 0203 change 0011
[135631.199751] usb 4-1-port4: status 0203 change 0011
[135631.275779] usb 3-1.1: new high-speed USB device number 3 using xhci_hcd
[135631.303781] hub 4-1:1.0: state 7 ports 4 chg 0012 evt 0000
[135631.326374] usb 4-1-port1: status 0203, change 0000, 5.0 Gb/s
[135631.425541] usb 3-1.1: default language 0x0409
[135631.426259] usb 3-1.1: udev 3, busnum 3, minor = 258
[135631.426263] usb 3-1.1: New USB device found, idVendor=2109,
idProduct=2817, bcdDevice= 7.b4
[135631.426266] usb 3-1.1: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[135631.426268] usb 3-1.1: Product: USB2.0 Hub
[135631.426270] usb 3-1.1: Manufacturer: VIA Labs, Inc.
[135631.426271] usb 3-1.1: SerialNumber: 000000000
[135631.426404] usb 3-1.1: usb_probe_device
[135631.426408] usb 3-1.1: configuration #1 chosen from 1 choice
[135631.427998] usb 3-1.1: adding 3-1.1:1.0 (config #1, interface 0)
[135631.428036] hub 3-1.1:1.0: usb_probe_interface
[135631.428038] hub 3-1.1:1.0: usb_probe_interface - got id
[135631.428041] hub 3-1.1:1.0: USB hub found
[135631.428249] hub 3-1.1:1.0: 4 ports detected
[135631.428251] hub 3-1.1:1.0: standalone hub
[135631.428252] hub 3-1.1:1.0: individual port power switching
[135631.428253] hub 3-1.1:1.0: individual port over-current protection
[135631.429146] hub 3-1.1:1.0: TT per port
[135631.429149] hub 3-1.1:1.0: TT requires at most 32 FS bit times (2664 ns)
[135631.429152] hub 3-1.1:1.0: Port indicators are supported
[135631.429153] hub 3-1.1:1.0: power on to power good time: 350ms
[135631.429578] hub 3-1.1:1.0: local power source is good
[135631.429963] hub 3-1.1:1.0: enabling power on all ports
[135631.521070] usb 4-1.1: new SuperSpeed USB device number 3 using xhci_hcd
[135631.551487] usb 3-1-port5: status 0501, change 0000, 480 Mb/s
[135631.551656] usb 3-1-port5: indicator auto status 0
[135631.579341] usb 4-1.1: skipped 1 descriptor after endpoint
[135631.579593] usb 4-1.1: default language 0x0409
[135631.580346] usb 4-1.1: udev 3, busnum 4, minor = 386
[135631.580348] usb 4-1.1: New USB device found, idVendor=2109,
idProduct=0817, bcdDevice= 7.b4
[135631.580351] usb 4-1.1: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[135631.580352] usb 4-1.1: Product: USB3.0 Hub
[135631.580353] usb 4-1.1: Manufacturer: VIA Labs, Inc.
[135631.580354] usb 4-1.1: SerialNumber: 000000000
[135631.580462] usb 4-1.1: usb_probe_device
[135631.580465] usb 4-1.1: configuration #1 chosen from 1 choice
[135631.582513] usb 4-1.1: adding 4-1.1:1.0 (config #1, interface 0)
[135631.582543] hub 4-1.1:1.0: usb_probe_interface
[135631.582546] hub 4-1.1:1.0: usb_probe_interface - got id
[135631.582548] hub 4-1.1:1.0: USB hub found
[135631.582740] hub 4-1.1:1.0: 4 ports detected
[135631.582742] hub 4-1.1:1.0: standalone hub
[135631.582744] hub 4-1.1:1.0: individual port power switching
[135631.582745] hub 4-1.1:1.0: individual port over-current protection
[135631.582746] hub 4-1.1:1.0: TT requires at most 8 FS bit times (666 ns)
[135631.582748] hub 4-1.1:1.0: power on to power good time: 350ms
[135631.583194] hub 4-1.1:1.0: local power source is good
[135631.583218] usb 4-1.1-port1: peered to 3-1.1-port1
[135631.583235] usb 4-1.1-port2: peered to 3-1.1-port2
[135631.583248] usb 4-1.1-port3: peered to 3-1.1-port3
[135631.583261] usb 4-1.1-port4: peered to 3-1.1-port4
[135631.655764] usb 3-1.5: new high-speed USB device number 4 using xhci_hcd
[135631.684088] hub 4-1.1:1.0: enabling power on all ports
[135631.685155] usb 4-1-port4: status 0203, change 0000, 5.0 Gb/s
[135631.760364] usb 3-1.5: default language 0x0409
[135631.760754] usb 3-1.5: udev 4, busnum 3, minor = 259
[135631.760757] usb 3-1.5: New USB device found, idVendor=2109,
idProduct=8817, bcdDevice= 0.01
[135631.760759] usb 3-1.5: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[135631.760761] usb 3-1.5: Product: USB Billboard Device
[135631.760762] usb 3-1.5: Manufacturer: VIA Labs, Inc.
[135631.760764] usb 3-1.5: SerialNumber: 0000000000000001
[135631.760864] usb 3-1.5: usb_probe_device
[135631.760867] usb 3-1.5: configuration #1 chosen from 1 choice
[135631.761670] usb 3-1.5: adding 3-1.5:1.0 (config #1, interface 0)
[135631.928390] usb 3-1.1-port3: status 0101 change 0001
[135631.995776] usb 1-5: usb auto-suspend, wakeup 0
[135632.039810] hub 3-1.1:1.0: state 7 ports 4 chg 0008 evt 0000
[135632.040137] usb 3-1.1-port3: status 0101, change 0000, 12 Mb/s
[135632.040300] usb 3-1.1-port3: indicator auto status 0
[135632.215784] usb 1-3: usb auto-suspend, wakeup 0
[135632.495840] usb 1-4: usb auto-suspend, wakeup 1
[135632.519768] hub 1-0:1.0: hub_suspend
[135632.523276] usb usb1: bus auto-suspend, wakeup 1
[135632.523467] xhci_hcd 0000:00:14.0: hcd_pci_runtime_suspend: 0
[135636.983657] xhci_hcd 0000:39:00.0: Timeout while waiting for setup
device command
[135636.983756] usb 4-1.1: kworker/3:1 timed out on ep0in len=0/4
[135636.984687] hub 4-1.1:1.0: state 7 ports 4 chg 0000 evt 0000
[135636.984903] hub 4-1.1:1.0: state 7 ports 4 chg 0000 evt 0008
[135636.985555] hub 4-1.1:1.0: hub_suspend
[135636.985997] usb 4-1.1: usb auto-suspend, wakeup 1
[135637.005910] usb 4-1.1: usb auto-resume
[135637.071744] usb 4-1.1: Waited 0ms for CONNECT
[135637.071751] usb 4-1.1: finish resume
[135637.072442] hub 4-1.1:1.0: hub_resume
[135637.100903] usb 4-1.1-port3: link state change
[135637.101072] usb 4-1.1-port3: do warm reset, port only
[135637.160024] usb 4-1.1-port3: not warm reset yet, waiting 50ms
[135642.359752] xhci_hcd 0000:39:00.0: Timeout while waiting for setup
device command
[135642.359904] usb 4-1.1: kworker/1:0 timed out on ep0in len=0/4
[135642.360403] usb 4-1.1-port3: not warm reset yet, waiting 200ms
[135642.567550] usb 4-1.4: device not accepting address 4, error -62
[135642.567787] usb 4-1.1-port3: not warm reset yet, waiting 200ms
[135642.587834] usb 3-1.1-port3: not reset yet, waiting 10ms
[135642.608022] usb 3-1.1-port3: not reset yet, waiting 10ms
[135642.627960] usb 3-1.1-port3: not reset yet, waiting 200ms
[135642.779575] usb 4-1.1-port3: not warm reset yet, waiting 200ms
[135642.836010] usb 3-1.1-port3: not reset yet, waiting 200ms
[135642.987924] usb 4-1.1-port3: not warm reset yet, waiting 200ms
[135642.989649] usb 4-1.1-port3: not enabled, trying warm reset again...
[135643.044090] usb 3-1.1-port3: not reset yet, waiting 200ms
[135643.253218] usb 3-1.1-port3: not reset yet, waiting 200ms
[135643.254188] hub 3-1.1:1.0: state 7 ports 4 chg 0000 evt 0008
[135643.254573] usb 3-1.1-port3: status 0100, change 0001, 12 Mb/s
[135643.254782] usb 3-1.1-port3: indicator auto status 0
[135643.255501] hub 4-1.1:1.0: state 7 ports 4 chg 0000 evt 0008
[135643.256309] usb 4-1.1-port3: status 0203, change 0001, 5.0 Gb/s
[135643.272060] usb 4-1-port4: not reset yet, waiting 10ms
[135643.292703] usb 4-1-port4: not reset yet, waiting 10ms
[135643.311459] usb 4-1-port4: not reset yet, waiting 200ms
[135643.395529] usb 3-1.1-port3: debounce total 100ms stable 100ms
status 0x100
[135643.395546] hub 3-1.1:1.0: hub_suspend
[135643.395900] usb 3-1.1: usb auto-suspend, wakeup 1
[135643.399598] usb 4-1.1-port3: debounce total 100ms stable 100ms
status 0x203
[135648.759590] xhci_hcd 0000:39:00.0: Timeout while waiting for setup
device command
[135654.135471] xhci_hcd 0000:39:00.0: Timeout while waiting for setup
device command
[135654.343365] usb 4-1.4: device not accepting address 5, error -62
[135654.343741] usb 4-1-port4: attempt power cycle
[135654.423462] usb 4-1.1.3: new SuperSpeed USB device number 6 using
xhci_hcd
[135654.443569] usb 4-1.1.3: USB quirks for this device: 400
[135654.443996] usb 4-1.1.3: skipped 1 descriptor after endpoint
[135654.444015] usb 4-1.1.3: skipped 1 descriptor after endpoint
[135654.444026] usb 4-1.1.3: skipped 1 descriptor after endpoint
[135654.444146] usb 4-1.1.3: skipped 3 descriptors after interface
[135654.444157] usb 4-1.1.3: skipped 1 descriptor after endpoint
[135654.444166] usb 4-1.1.3: skipped 1 descriptor after endpoint
[135654.444174] usb 4-1.1.3: skipped 1 descriptor after endpoint
[135654.444231] usb 4-1.1.3: default language 0x0409
[135654.444459] usb 4-1.1.3: udev 6, busnum 4, minor = 389
[135654.444472] usb 4-1.1.3: New USB device found, idVendor=0bda,
idProduct=8153, bcdDevice=30.00
[135654.444485] usb 4-1.1.3: New USB device strings: Mfr=1, Product=2,
SerialNumber=6
[135654.444495] usb 4-1.1.3: Product: USB 10/100/1000 LAN
[135654.444503] usb 4-1.1.3: Manufacturer: Realtek
[135654.444510] usb 4-1.1.3: SerialNumber: 000001
[135654.444978] r8152-cfgselector 4-1.1.3: usb_probe_device
[135654.447545] r8152-cfgselector 4-1.1.3: adding 4-1.1.3:1.0 (config
#1, interface 0)
[135654.447741] r8152 4-1.1.3:1.0: usb_probe_interface
[135654.447753] r8152 4-1.1.3:1.0: usb_probe_interface - got id
[135654.527864] r8152-cfgselector 4-1.1.3: reset SuperSpeed USB device
number 6 using xhci_hcd
[135654.547443] r8152-cfgselector 4-1.1.3: USB quirks for this device: 400
[135654.570025] r8152 4-1.1.3:1.0: load rtl8153a-4 v2 02/07/20 successfully
[135654.601390] r8152 4-1.1.3:1.0 eth0: v1.12.13
[135654.602115] hub 4-1.1:1.0: state 7 ports 4 chg 0000 evt 0008
[135660.535346] xhci_hcd 0000:39:00.0: Timeout while waiting for setup
device command
[135665.911069] xhci_hcd 0000:39:00.0: Timeout while waiting for setup
device command
[135666.118792] usb 4-1.4: device not accepting address 7, error -62
[135666.138995] usb 4-1-port4: not reset yet, waiting 10ms
[135666.158967] usb 4-1-port4: not reset yet, waiting 10ms
[135666.178919] usb 4-1-port4: not reset yet, waiting 200ms
[135666.387360] usb 4-1-port4: not reset yet, waiting 200ms
[135666.595345] usb 4-1-port4: not reset yet, waiting 200ms
[135666.803419] usb 4-1-port4: not reset yet, waiting 200ms
[135666.804994] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0010
[135666.861597] r8152 4-1.1.3:1.0 enx00e04ceabb21: renamed from eth0
[135666.922339] r8152 4-1.1.3:1.0 enx00e04ceabb21: carrier on
[135667.321109] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0010
[135667.321537] usb 4-1-port4: link state change
[135667.321750] usb 4-1-port4: do warm reset, port only
[135667.379354] usb 4-1-port4: not warm reset yet, waiting 50ms
[135667.498936] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0010
[135667.499385] usb 4-1-port4: status 0203, change 0001, 5.0 Gb/s
[135667.642781] usb 4-1-port4: debounce total 100ms stable 100ms status
0x203
[135672.822965] xhci_hcd 0000:39:00.0: Timeout while waiting for setup
device command
[135678.198866] xhci_hcd 0000:39:00.0: Timeout while waiting for setup
device command
[135678.406490] usb 4-1.4: device not accepting address 9, error -62
[135678.430725] usb 4-1-port4: not reset yet, waiting 10ms
[135678.450736] usb 4-1-port4: not reset yet, waiting 10ms
[135678.470466] usb 4-1-port4: not reset yet, waiting 200ms
[135678.678449] usb 4-1-port4: not reset yet, waiting 200ms
[135678.890098] usb 4-1-port4: not reset yet, waiting 200ms
[135679.094465] usb 4-1-port4: not reset yet, waiting 200ms
[135679.095792] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0010
[135679.608911] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0010
[135679.609291] usb 4-1-port4: link state change
[135679.609623] usb 4-1-port4: do warm reset, port only
[135679.667019] usb 4-1-port4: not warm reset yet, waiting 50ms
[135679.727000] usb 4-1-port4: not warm reset yet, waiting 200ms
[135679.934968] usb 4-1-port4: not warm reset yet, waiting 200ms
[135680.142806] usb 4-1-port4: not warm reset yet, waiting 200ms
[135680.350683] usb 4-1-port4: not warm reset yet, waiting 200ms
[135680.824878] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0010
[135680.825079] usb 4-1-port4: link state change
```
The last part continues until unplugging device, but this might be a
separate issue, as the Ethernet connection was functional.
So from
[135654.601390] r8152 4-1.1.3:1.0 eth0: v1.12.13
to
[135666.861597] r8152 4-1.1.3:1.0 enx00e04ceabb21: renamed from eth0
it took 12 seconds.
Is that a problem with the laptop or the adapter? And can it be fixed
somehow?
Kind regards,
Paul
[1]:
https://lmp-adapter.com/product/lmp-usb-c-mini-dock/?attribute_pa_color=silver
"LMP USB-C mini Dock (P/N 15954)"
PS:
```
$ usb-devices
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh=12
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev=06.08
S: Manufacturer=Linux 6.8.0-rc5+ xhci-hcd
S: Product=xHCI Host Controller
S: SerialNumber=0000:00:14.0
C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0cf3 ProdID=e300 Rev=00.01
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
T: Bus=01 Lev=01 Prnt=02 Port=03 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=04f3 ProdID=2234 Rev=11.11
S: Manufacturer=ELAN
S: Product=Touchscreen
C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=03(HID ) Sub=00 Prot=00 Driver=usbhid
E: Ad=02(O) Atr=03(Int.) MxPS= 32 Ivl=2ms
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=1ms
T: Bus=01 Lev=01 Prnt=03 Port=04 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0c45 ProdID=670c Rev=56.26
S: Manufacturer=CN09GTFMLOG008C8B7FWA01
S: Product=Integrated_Webcam_HD
C: #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=0e(video) Sub=01 Prot=00 Driver=uvcvideo
E: Ad=83(I) Atr=03(Int.) MxPS= 16 Ivl=4ms
I: If#= 1 Alt= 0 #EPs= 1 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideo
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=5000 MxCh= 6
D: Ver= 3.00 Cls=09(hub ) Sub=00 Prot=03 MxPS= 9 #Cfgs= 1
P: Vendor=1d6b ProdID=0003 Rev=06.08
S: Manufacturer=Linux 6.8.0-rc5+ xhci-hcd
S: Product=xHCI Host Controller
S: SerialNumber=0000:00:14.0
C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 2
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev=06.08
S: Manufacturer=Linux 6.8.0-rc5+ xhci-hcd
S: Product=xHCI Host Controller
S: SerialNumber=0000:39:00.0
C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 5
D: Ver= 2.10 Cls=09(hub ) Sub=00 Prot=02 MxPS=64 #Cfgs= 1
P: Vendor=2109 ProdID=2817 Rev=05.e3
S: Manufacturer=VIA Labs, Inc.
S: Product=USB2.0 Hub
S: SerialNumber=000000000
C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 1 #EPs= 1 Cls=09(hub ) Sub=00 Prot=02 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms
T: Bus=03 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 3 Spd=480 MxCh= 4
D: Ver= 2.10 Cls=09(hub ) Sub=00 Prot=02 MxPS=64 #Cfgs= 1
P: Vendor=2109 ProdID=2817 Rev=07.b4
S: Manufacturer=VIA Labs, Inc.
S: Product=USB2.0 Hub
S: SerialNumber=000000000
C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 1 #EPs= 1 Cls=09(hub ) Sub=00 Prot=02 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms
T: Bus=03 Lev=02 Prnt=03 Port=04 Cnt=01 Dev#= 5 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=11(blbrd) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2109 ProdID=8817 Rev=00.01
S: Manufacturer=VIA Labs, Inc.
S: Product=USB Billboard Device
S: SerialNumber=0000000000000001
C: #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 0 Cls=11(blbrd) Sub=00 Prot=00 Driver=(none)
T: Bus=04 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=10000 MxCh= 2
D: Ver= 3.10 Cls=09(hub ) Sub=00 Prot=03 MxPS= 9 #Cfgs= 1
P: Vendor=1d6b ProdID=0003 Rev=06.08
S: Manufacturer=Linux 6.8.0-rc5+ xhci-hcd
S: Product=xHCI Host Controller
S: SerialNumber=0000:39:00.0
C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=5000 MxCh= 4
D: Ver= 3.20 Cls=09(hub ) Sub=00 Prot=03 MxPS= 9 #Cfgs= 1
P: Vendor=2109 ProdID=0817 Rev=05.e3
S: Manufacturer=VIA Labs, Inc.
S: Product=USB3.0 Hub
S: SerialNumber=000000000
C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=13(Int.) MxPS= 2 Ivl=16ms
T: Bus=04 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 3 Spd=5000 MxCh= 4
D: Ver= 3.20 Cls=09(hub ) Sub=00 Prot=03 MxPS= 9 #Cfgs= 1
P: Vendor=2109 ProdID=0817 Rev=07.b4
S: Manufacturer=VIA Labs, Inc.
S: Product=USB3.0 Hub
S: SerialNumber=000000000
C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=13(Int.) MxPS= 2 Ivl=16ms
T: Bus=04 Lev=03 Prnt=03 Port=02 Cnt=01 Dev#= 5 Spd=5000 MxCh= 0
D: Ver= 3.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 2
P: Vendor=0bda ProdID=8153 Rev=30.00
S: Manufacturer=Realtek
S: Product=USB 10/100/1000 LAN
S: SerialNumber=000001
C: #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr=288mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=00 Driver=r8152
E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 2 Ivl=16ms
T: Bus=04 Lev=02 Prnt=05 Port=03 Cnt=01 Dev#= 4 Spd=5000 MxCh= 0
D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
P: Vendor=058f ProdID=8468 Rev=01.00
S: Manufacturer=Generic
S: Product=Mass Storage Device
S: SerialNumber=058F84688461
C: #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=800mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
```
+Mathias
On Sat, Feb 24, 2024 at 08:45:43PM +0100, Paul Menzel wrote:
> Dear Linux folks,
>
>
> I suspended a Dell XPS 13 9360 with no devices attached into ACPI S3. Then
> connecting an LMP USB-C mini Dock (P/N 15954) [1] with an Ethernet cable
> attached to the left USB-C port and resumed the system from ACPI S3. It took
> 37 seconds, until the link was established.
>
> ```
> [ 0.000000] Linux version 6.8.0-rc5+
> ([email protected]) (gcc (Debian 13.2.0-13) 13.2.0, GNU
> ld (GNU Binutils for Debian) 2.42) #27 SMP PREEMPT_DYNAMIC Wed Feb 21
> 09:09:49 CET 2024
> [ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-6.8.0-rc5+
> root=UUID=32e29882-d94d-4a92-9ee4-4d03002bfa29 ro quiet pci=noaer
> mem_sleep_default=deep log_buf_len=8M cryptomgr.notests usbcore.dyndbg=+p
> […]
> [ 0.000000] DMI: Dell Inc. XPS 13 9360/0596KF, BIOS 2.21.0 06/02/2022
> […]
> [135623.339094] PM: suspend entry (deep)
> [135623.345592] Filesystems sync: 0.006 seconds
> [135623.349062] Freezing user space processes
> [135623.352053] Freezing user space processes completed (elapsed 0.002
> seconds)
> [135623.352068] OOM killer disabled.
> [135623.352071] Freezing remaining freezable tasks
> [135623.353870] Freezing remaining freezable tasks completed (elapsed 0.001
> seconds)
> [135623.353985] printk: Suspending console(s) (use no_console_suspend to
> debug)
> [134781.473459] xhci_hcd 0000:00:14.0: hcd_pci_runtime_resume: 0
> [134781.473482] usb usb1: usb auto-resume
> [134781.473509] usb usb2: usb auto-resume
> [134781.473517] hub 1-0:1.0: hub_resume
> [134781.473540] hub 2-0:1.0: hub_resume
> [134781.473597] usb usb1-port3: status 0107 change 0000
> [134781.473616] usb usb1-port4: status 0107 change 0000
> [134781.473632] usb usb1-port5: status 0507 change 0000
> [134781.505615] hub 2-0:1.0: hub_suspend
> [134781.505712] usb usb2: bus suspend, wakeup 0
> [134781.521037] usb 1-4: usb auto-resume
> [134781.589048] usb 1-4: Waited 0ms for CONNECT
> [134781.589071] usb 1-4: finish resume
> [134781.589879] usb 1-4: usb suspend, wakeup 0
> [134781.589992] hub 1-0:1.0: hub_suspend
> [134781.590103] usb usb1: bus suspend, wakeup 0
> [134781.999962] ACPI: EC: interrupt blocked
> [134782.002105] xhci_hcd 0000:00:14.0: wakeup: 1
> [134782.033016] xhci_hcd 0000:00:14.0: --> PCI D3hot
> [134782.033126] ACPI: PM: Preparing to enter system sleep state S3
> [134782.049143] ACPI: EC: event blocked
> [134782.049148] ACPI: EC: EC stopped
> [134782.049150] ACPI: PM: Saving platform NVS memory
> [134782.052592] Disabling non-boot CPUs ...
> [134782.056035] smpboot: CPU 1 is now offline
> [134782.060287] smpboot: CPU 2 is now offline
> [134782.063001] smpboot: CPU 3 is now offline
> [134782.072093] ACPI: PM: Low-level resume complete
> [134782.072137] ACPI: EC: EC started
> [134782.072138] ACPI: PM: Restoring platform NVS memory
> [134782.074101] Enabling non-boot CPUs ...
> [134782.074126] smpboot: Booting Node 0 Processor 1 APIC 0x2
> [134782.074972] CPU1 is up
> [134782.074989] smpboot: Booting Node 0 Processor 2 APIC 0x1
> [134782.075759] CPU2 is up
> [134782.075776] smpboot: Booting Node 0 Processor 3 APIC 0x3
> [134782.076474] CPU3 is up
> [134782.079463] ACPI: PM: Waking up from system sleep state S3
> [134782.126767] ACPI: EC: interrupt unblocked
> [134782.161453] ACPI: EC: event unblocked
> [134782.164047] usb usb1: usb resume
> [134782.164088] usb usb2: usb resume
> [134782.164127] hub 2-0:1.0: hub_resume
> [134782.164970] i915 0000:00:02.0: [drm] [ENCODER:94:DDI A/PHY A] is
> disabled/in DSI mode with an ungated DDI clock, gate it
> [134782.164981] i915 0000:00:02.0: [drm] [ENCODER:102:DDI B/PHY B] is
> disabled/in DSI mode with an ungated DDI clock, gate it
> [134782.164989] i915 0000:00:02.0: [drm] [ENCODER:113:DDI C/PHY C] is
> disabled/in DSI mode with an ungated DDI clock, gate it
> [134782.174398] nvme nvme0: 4/0/0 default/read/poll queues
> [134782.175094] hub 1-0:1.0: hub_resume
> [134782.175153] usb usb1-port3: status 0101 change 0001
> [134782.175176] usb usb1-port4: status 0101 change 0001
> [134782.175195] usb usb1-port5: status 0101 change 0001
> [134782.299331] usb 1-3: Waited 0ms for CONNECT
> [134782.299336] usb 1-5: Waited 0ms for CONNECT
> [134782.299339] usb 1-3: finish reset-resume
> [134782.299343] usb 1-5: finish reset-resume
> [134782.303359] usb 1-4: Waited 0ms for CONNECT
> [134782.303363] usb 1-4: finish reset-resume
> [134782.411326] atkbd serio0: Failed to deactivate keyboard on
> isa0060/serio0
> [134782.427585] usb 1-3: reset full-speed USB device number 2 using xhci_hcd
> [134782.703558] usb 1-5: reset high-speed USB device number 4 using xhci_hcd
> [134782.979518] usb 1-4: reset full-speed USB device number 3 using xhci_hcd
> [134783.137568] OOM killer enabled.
> [134783.137570] Restarting tasks ...
> [134783.137607] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0000
> [134783.138111] hub 2-0:1.0: hub_suspend
> [134783.138130] usb usb2: bus auto-suspend, wakeup 1
> [134783.139896] usb usb2: usb wakeup-resume
> [134783.139903] usb usb2: usb auto-resume
> [134783.141145] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0010
> [134783.144869] done.
> [134783.144884] random: crng reseeded on system resumption
> [134783.155322] hub 2-0:1.0: hub_resume
> [134783.187376] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0000
> [134783.187433] hub 2-0:1.0: hub_suspend
> [134783.187439] usb usb2: bus auto-suspend, wakeup 1
> [134783.225883] PM: suspend exit
> [134783.295100] Process accounting resumed
> [134783.483053] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04:
> bound 0000:00:02.0 (ops i915_hdcp_ops [i915])
> [134785.095304] usb 1-3: usb auto-suspend, wakeup 0
> [134785.439272] usb 1-5: usb auto-suspend, wakeup 0
> [134785.583269] usb 1-4: usb auto-suspend, wakeup 1
> [134785.603266] hub 1-0:1.0: hub_suspend
> [134785.603280] usb usb1: bus auto-suspend, wakeup 1
> [134785.603448] xhci_hcd 0000:00:14.0: hcd_pci_runtime_suspend: 0
> [134788.708764] wlp58s0: authenticate with a4:97:33:06:77:d3 (local
> address=9c:b6:d0:d1:6a:b1)
> [134788.708770] wlp58s0: send auth to a4:97:33:06:77:d3 (try 1/3)
> [134788.709809] wlp58s0: authenticated
> [134788.711232] wlp58s0: associate with a4:97:33:06:77:d3 (try 1/3)
> [134788.714287] wlp58s0: RX AssocResp from a4:97:33:06:77:d3 (capab=0x511
> status=0 aid=102)
> [134788.717462] wlp58s0: associated
> [134788.721574] wlp58s0: Limiting TX power to 30 (30 - 0) dBm as advertised
> by a4:97:33:06:77:d3
> [135619.981952] xhci_hcd 0000:00:14.0: hcd_pci_runtime_resume: 0
> [135619.982043] usb usb1: usb wakeup-resume
> [135619.982048] usb usb1: usb auto-resume
> [135619.982072] hub 1-0:1.0: hub_resume
> [135619.982103] usb usb1-port3: status 0107 change 0000
> [135619.982111] usb usb1-port4: status 0107 change 0000
> [135619.982119] usb usb1-port5: status 0507 change 0000
> [135619.982163] usb usb2: usb wakeup-resume
> [135619.982165] usb usb2: usb auto-resume
> [135619.982188] hub 2-0:1.0: hub_resume
> [135619.982198] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0000
> [135619.987438] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0000
> [135620.009646] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0000
> [135620.009700] hub 2-0:1.0: hub_suspend
> [135620.009705] usb usb2: bus auto-suspend, wakeup 1
> [135620.148856] wlp58s0: deauthenticating from a4:97:33:06:77:d3 by local
> choice (Reason: 3=DEAUTH_LEAVING)
> [135620.157614] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0010
> [135620.177775] usb 1-4: usb wakeup-resume
> [135620.197833] usb 1-4: Waited 0ms for CONNECT
> [135620.197838] usb 1-4: finish resume
> [135620.198318] usb usb1-port4: resume, status 0
> [135622.717569] usb 1-4: usb auto-suspend, wakeup 1
> [135622.737533] hub 1-0:1.0: hub_suspend
> [135622.737550] usb usb1: bus auto-suspend, wakeup 1
> [135622.737701] xhci_hcd 0000:00:14.0: hcd_pci_runtime_suspend: 0
> [135623.339094] PM: suspend entry (deep)
> [135623.345592] Filesystems sync: 0.006 seconds
> [135623.349062] Freezing user space processes
> [135623.352053] Freezing user space processes completed (elapsed 0.002
> seconds)
> [135623.352068] OOM killer disabled.
> [135623.352071] Freezing remaining freezable tasks
> [135623.353870] Freezing remaining freezable tasks completed (elapsed 0.001
> seconds)
> [135623.353985] printk: Suspending console(s) (use no_console_suspend to
> debug)
> [135623.390281] xhci_hcd 0000:00:14.0: hcd_pci_runtime_resume: 0
> [135623.390306] usb usb1: usb auto-resume
> [135623.390319] usb usb2: usb auto-resume
> [135623.390340] hub 1-0:1.0: hub_resume
> [135623.390358] hub 2-0:1.0: hub_resume
> [135623.390535] usb usb1-port3: status 0107 change 0000
> [135623.390593] usb usb1-port4: status 0107 change 0000
> [135623.390671] usb usb1-port5: status 0507 change 0000
> [135623.417795] hub 2-0:1.0: hub_suspend
> [135623.417832] usb usb2: bus suspend, wakeup 0
> [135623.437691] usb 1-4: usb auto-resume
> [135623.505705] usb 1-4: Waited 0ms for CONNECT
> [135623.505722] usb 1-4: finish resume
> [135623.506183] usb 1-4: usb suspend, wakeup 0
> [135623.506226] hub 1-0:1.0: hub_suspend
> [135623.506285] usb usb1: bus suspend, wakeup 0
> [135623.918326] ACPI: EC: interrupt blocked
> [135623.922119] xhci_hcd 0000:00:14.0: wakeup: 1
> [135623.953670] xhci_hcd 0000:00:14.0: --> PCI D3hot
> [135623.953772] ACPI: PM: Preparing to enter system sleep state S3
> [135623.963290] ACPI: EC: event blocked
> [135623.963291] ACPI: EC: EC stopped
> [135623.963292] ACPI: PM: Saving platform NVS memory
> [135623.964787] Disabling non-boot CPUs ...
> [135623.966332] smpboot: CPU 1 is now offline
> [135623.968749] smpboot: CPU 2 is now offline
> [135623.970630] smpboot: CPU 3 is now offline
> [135623.975734] ACPI: PM: Low-level resume complete
> [135623.975778] ACPI: EC: EC started
> [135623.975779] ACPI: PM: Restoring platform NVS memory
> [135623.977741] Enabling non-boot CPUs ...
> [135623.977767] smpboot: Booting Node 0 Processor 1 APIC 0x2
> [135623.978525] CPU1 is up
> [135623.978542] smpboot: Booting Node 0 Processor 2 APIC 0x1
> [135623.979283] CPU2 is up
> [135623.979299] smpboot: Booting Node 0 Processor 3 APIC 0x3
> [135623.979965] CPU3 is up
> [135623.982953] ACPI: PM: Waking up from system sleep state S3
> [135628.953183] ACPI: EC: interrupt unblocked
> [135629.001792] ACPI: EC: event unblocked
> [135629.004635] usb usb1: usb resume
> [135629.004637] usb usb2: usb resume
> [135629.004658] hub 2-0:1.0: hub_resume
> [135629.005256] i915 0000:00:02.0: [drm] [ENCODER:94:DDI A/PHY A] is
> disabled/in DSI mode with an ungated DDI clock, gate it
> [135629.005261] i915 0000:00:02.0: [drm] [ENCODER:102:DDI B/PHY B] is
> disabled/in DSI mode with an ungated DDI clock, gate it
> [135629.005264] i915 0000:00:02.0: [drm] [ENCODER:113:DDI C/PHY C] is
> disabled/in DSI mode with an ungated DDI clock, gate it
> [135629.014542] nvme nvme0: 4/0/0 default/read/poll queues
> [135629.015207] hub 1-0:1.0: hub_resume
> [135629.015226] usb usb1-port3: status 0101 change 0001
> [135629.015235] usb usb1-port4: status 0101 change 0001
> [135629.015243] usb usb1-port5: status 0101 change 0001
> [135629.139830] usb 1-5: Waited 0ms for CONNECT
> [135629.139834] usb 1-5: finish reset-resume
> [135629.139836] usb 1-3: Waited 0ms for CONNECT
> [135629.139838] usb 1-3: finish reset-resume
> [135629.139876] usb 1-4: Waited 0ms for CONNECT
> [135629.139879] usb 1-4: finish reset-resume
> [135629.268021] usb 1-5: reset high-speed USB device number 4 using xhci_hcd
> [135629.544069] usb 1-3: reset full-speed USB device number 2 using xhci_hcd
> [135629.820015] usb 1-4: reset full-speed USB device number 3 using xhci_hcd
> [135629.976929] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04:
> bound 0000:00:02.0 (ops i915_hdcp_ops [i915])
> [135629.977326] OOM killer enabled.
> [135629.977329] Restarting tasks ...
> [135629.977351] pci 0000:01:00.0: [8086:1576] type 01 class 0x060400 PCIe
> Switch Upstream Port
> [135629.977404] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0010
> [135629.977405] pci 0000:01:00.0: PCI bridge to [bus 02-39]
> [135629.977425] pci 0000:01:00.0: bridge window [mem
> 0xc4000000-0xda0fffff]
> [135629.977446] pci 0000:01:00.0: bridge window [mem 0xa0000000-0xc1ffffff
> 64bit pref]
> [135629.977475] pci 0000:01:00.0: enabling Extended Tags
> [135629.977561] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0000
> [135629.977886] pci 0000:01:00.0: supports D1 D2
> [135629.977889] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
> [135629.977998] pci 0000:01:00.0: 15.752 Gb/s available PCIe bandwidth,
> limited by 8.0 GT/s PCIe x2 link at 0000:00:1c.0 (capable of 31.504 Gb/s
> with 8.0 GT/s PCIe x4 link)
> [135629.981650] pci 0000:02:00.0: [8086:1576] type 01 class 0x060400 PCIe
> Switch Downstream Port
> [135629.981716] pci 0000:02:00.0: PCI bridge to [bus 03]
> [135629.981738] pci 0000:02:00.0: bridge window [mem
> 0xda000000-0xda0fffff]
> [135629.981781] pci 0000:02:00.0: enabling Extended Tags
> [135629.981937] pci 0000:02:00.0: supports D1 D2
> [135629.981940] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
> [135629.982333] pci 0000:02:01.0: [8086:1576] type 01 class 0x060400 PCIe
> Switch Downstream Port
> [135629.982387] pci 0000:02:01.0: PCI bridge to [bus 04-38]
> [135629.982405] pci 0000:02:01.0: bridge window [mem
> 0xc4000000-0xd9efffff]
> [135629.982426] pci 0000:02:01.0: bridge window [mem 0xa0000000-0xc1ffffff
> 64bit pref]
> [135629.982450] pci 0000:02:01.0: enabling Extended Tags
> [135629.982621] pci 0000:02:01.0: supports D1 D2
> [135629.982624] pci 0000:02:01.0: PME# supported from D0 D1 D2 D3hot D3cold
> [135629.983907] hub 2-0:1.0: hub_suspend
> [135629.983945] usb usb2: bus auto-suspend, wakeup 1
> [135629.984444] done.
> [135629.984460] random: crng reseeded on system resumption
> [135629.986390] pci 0000:02:02.0: [8086:1576] type 01 class 0x060400 PCIe
> Switch Downstream Port
> [135629.986441] pci 0000:02:02.0: PCI bridge to [bus 39]
> [135629.986458] pci 0000:02:02.0: bridge window [mem
> 0xd9f00000-0xd9ffffff]
> [135629.986492] pci 0000:02:02.0: enabling Extended Tags
> [135629.986629] pci 0000:02:02.0: supports D1 D2
> [135629.986631] pci 0000:02:02.0: PME# supported from D0 D1 D2 D3hot D3cold
> [135629.986929] pci 0000:01:00.0: PCI bridge to [bus 02-39]
> [135629.987022] pci 0000:02:00.0: PCI bridge to [bus 03]
> [135629.987103] pci 0000:02:01.0: PCI bridge to [bus 04-38]
> [135629.990420] pci 0000:39:00.0: [8086:15b5] type 00 class 0x0c0330 PCIe
> Endpoint
> [135629.990454] pci 0000:39:00.0: BAR 0 [mem 0xd9f00000-0xd9f0ffff]
> [135629.990554] pci 0000:39:00.0: enabling Extended Tags
> [135629.997287] pci 0000:39:00.0: supports D1 D2
> [135629.997295] pci 0000:39:00.0: PME# supported from D0 D1 D2 D3hot D3cold
> [135629.997443] pci 0000:39:00.0: 8.000 Gb/s available PCIe bandwidth,
> limited by 2.5 GT/s PCIe x4 link at 0000:02:02.0 (capable of 31.504 Gb/s
> with 8.0 GT/s PCIe x4 link)
> [135629.997814] pci 0000:02:02.0: PCI bridge to [bus 39]
> [135629.997867] pci_bus 0000:02: Allocating resources
> [135629.997892] pci 0000:02:01.0: bridge window [io 0x1000-0x0fff] to [bus
> 04-38] add_size 1000
> [135629.997901] pci 0000:02:02.0: bridge window [io 0x1000-0x0fff] to [bus
> 39] add_size 1000
> [135629.997904] pci 0000:02:02.0: bridge window [mem 0x00100000-0x000fffff
> 64bit pref] to [bus 39] add_size 200000 add_align 100000
> [135629.997908] pci 0000:01:00.0: bridge window [io 0x1000-0x0fff] to [bus
> 02-39] add_size 2000
> [135629.997912] pci 0000:01:00.0: bridge window [io size 0x2000]: can't
> assign; no space
> [135629.997915] pci 0000:01:00.0: bridge window [io size 0x2000]: failed to
> assign
> [135629.997917] pci 0000:01:00.0: bridge window [io size 0x2000]: can't
> assign; no space
> [135629.997924] pci 0000:01:00.0: bridge window [io size 0x2000]: failed to
> assign
> [135629.997929] pci 0000:02:02.0: bridge window [mem size 0x00200000 64bit
> pref]: can't assign; no space
> [135629.997931] pci 0000:02:02.0: bridge window [mem size 0x00200000 64bit
> pref]: failed to assign
> [135629.997932] pci 0000:02:01.0: bridge window [io size 0x1000]: can't
> assign; no space
> [135629.997934] pci 0000:02:01.0: bridge window [io size 0x1000]: failed to
> assign
> [135629.997935] pci 0000:02:02.0: bridge window [io size 0x1000]: can't
> assign; no space
> [135629.997937] pci 0000:02:02.0: bridge window [io size 0x1000]: failed to
> assign
> [135629.997940] pci 0000:02:02.0: bridge window [mem size 0x00200000 64bit
> pref]: can't assign; no space
> [135629.997942] pci 0000:02:02.0: bridge window [mem size 0x00200000 64bit
> pref]: failed to assign
> [135629.997982] pci 0000:02:02.0: bridge window [io size 0x1000]: can't
> assign; no space
> [135629.998009] pci 0000:02:02.0: bridge window [io size 0x1000]: failed to
> assign
> [135629.998037] pci 0000:02:01.0: bridge window [io size 0x1000]: can't
> assign; no space
> [135629.998063] pci 0000:02:01.0: bridge window [io size 0x1000]: failed to
> assign
> [135629.998125] pci 0000:02:00.0: PCI bridge to [bus 03]
> [135629.998131] pci 0000:02:00.0: bridge window [mem
> 0xda000000-0xda0fffff]
> [135629.998140] pci 0000:02:01.0: PCI bridge to [bus 04-38]
> [135629.998145] pci 0000:02:01.0: bridge window [mem
> 0xc4000000-0xd9efffff]
> [135629.998149] pci 0000:02:01.0: bridge window [mem 0xa0000000-0xc1ffffff
> 64bit pref]
> [135629.998156] pci 0000:02:02.0: PCI bridge to [bus 39]
> [135629.998161] pci 0000:02:02.0: bridge window [mem
> 0xd9f00000-0xd9ffffff]
> [135629.998169] pci 0000:01:00.0: PCI bridge to [bus 02-39]
> [135629.998175] pci 0000:01:00.0: bridge window [mem
> 0xc4000000-0xda0fffff]
> [135629.998179] pci 0000:01:00.0: bridge window [mem 0xa0000000-0xc1ffffff
> 64bit pref]
> [135630.003545] xhci_hcd 0000:39:00.0: xHCI Host Controller
> [135630.003562] xhci_hcd 0000:39:00.0: new USB bus registered, assigned bus
> number 3
> [135630.004799] xhci_hcd 0000:39:00.0: hcc params 0x200077c1 hci version
> 0x110 quirks 0x0000000200009810
> [135630.004875] xhci_hcd 0000:39:00.0: supports USB remote wakeup
> [135630.024937] xhci_hcd 0000:39:00.0: xHCI Host Controller
> [135630.024946] xhci_hcd 0000:39:00.0: new USB bus registered, assigned bus
> number 4
> [135630.024953] xhci_hcd 0000:39:00.0: Host supports USB 3.1 Enhanced
> SuperSpeed
> [135630.024956] xhci_hcd 0000:39:00.0: supports USB remote wakeup
> [135630.025073] usb usb3: default language 0x0409
> [135630.025089] usb usb3: udev 1, busnum 3, minor = 256
> [135630.025092] usb usb3: New USB device found, idVendor=1d6b,
> idProduct=0002, bcdDevice= 6.08
> [135630.025095] usb usb3: New USB device strings: Mfr=3, Product=2,
> SerialNumber=1
> [135630.025097] usb usb3: Product: xHCI Host Controller
> [135630.025099] usb usb3: Manufacturer: Linux 6.8.0-rc5+ xhci-hcd
> [135630.025100] usb usb3: SerialNumber: 0000:39:00.0
> [135630.076427] usb usb3: usb_probe_device
> [135630.076432] usb usb3: configuration #1 chosen from 1 choice
> [135630.076450] usb usb3: adding 3-0:1.0 (config #1, interface 0)
> [135630.077078] hub 3-0:1.0: usb_probe_interface
> [135630.077104] hub 3-0:1.0: usb_probe_interface - got id
> [135630.077127] hub 3-0:1.0: USB hub found
> [135630.077169] hub 3-0:1.0: 2 ports detected
> [135630.077171] hub 3-0:1.0: standalone hub
> [135630.077172] hub 3-0:1.0: no power switching (usb 1.0)
> [135630.077174] hub 3-0:1.0: individual port over-current protection
> [135630.077175] hub 3-0:1.0: Single TT
> [135630.077176] hub 3-0:1.0: TT requires at most 8 FS bit times (666 ns)
> [135630.077178] hub 3-0:1.0: power on to power good time: 20ms
> [135630.077188] hub 3-0:1.0: local power source is good
> [135630.078734] hub 3-0:1.0: trying to enable port power on non-switchable
> hub
> [135630.083747] usb usb4: skipped 1 descriptor after endpoint
> [135630.083784] usb usb4: default language 0x0409
> [135630.083877] usb usb4: udev 1, busnum 4, minor = 384
> [135630.083890] usb usb4: New USB device found, idVendor=1d6b,
> idProduct=0003, bcdDevice= 6.08
> [135630.083904] usb usb4: New USB device strings: Mfr=3, Product=2,
> SerialNumber=1
> [135630.083913] usb usb4: Product: xHCI Host Controller
> [135630.083921] usb usb4: Manufacturer: Linux 6.8.0-rc5+ xhci-hcd
> [135630.083927] usb usb4: SerialNumber: 0000:39:00.0
> [135630.091335] usb usb4: usb_probe_device
> [135630.091350] usb usb4: configuration #1 chosen from 1 choice
> [135630.091400] usb usb4: adding 4-0:1.0 (config #1, interface 0)
> [135630.091503] hub 4-0:1.0: usb_probe_interface
> [135630.091509] hub 4-0:1.0: usb_probe_interface - got id
> [135630.091517] hub 4-0:1.0: USB hub found
> [135630.091540] hub 4-0:1.0: 2 ports detected
> [135630.091546] hub 4-0:1.0: standalone hub
> [135630.091551] hub 4-0:1.0: no power switching (usb 1.0)
> [135630.091556] hub 4-0:1.0: individual port over-current protection
> [135630.091562] hub 4-0:1.0: TT requires at most 8 FS bit times (666 ns)
> [135630.091568] hub 4-0:1.0: power on to power good time: 100ms
> [135630.091590] hub 4-0:1.0: local power source is good
> [135630.097020] usb usb4-port1: peered to usb3-port1
> [135630.103851] usb usb3-port1: status 0101 change 0001
> [135630.109207] usb usb4: port-1 no _DSM function 5
> [135630.109224] usb usb4: port-2 no _DSM function 5
> [135630.109230] hub 4-0:1.0: trying to enable port power on non-switchable
> hub
> [135630.110174] pci_bus 0000:02: Allocating resources
> [135630.110197] pcieport 0000:02:01.0: bridge window [io 0x1000-0x0fff] to
> [bus 04-38] add_size 1000
> [135630.110205] pcieport 0000:02:02.0: bridge window [io 0x1000-0x0fff] to
> [bus 39] add_size 1000
> [135630.110210] pcieport 0000:02:02.0: bridge window [mem
> 0x00100000-0x000fffff 64bit pref] to [bus 39] add_size 200000 add_align
> 100000
> [135630.110218] pcieport 0000:01:00.0: bridge window [io 0x1000-0x0fff] to
> [bus 02-39] add_size 2000
> [135630.110224] pcieport 0000:01:00.0: bridge window [io size 0x2000]:
> can't assign; no space
> [135630.110228] pcieport 0000:01:00.0: bridge window [io size 0x2000]:
> failed to assign
> [135630.110233] pcieport 0000:01:00.0: bridge window [io size 0x2000]:
> can't assign; no space
> [135630.110236] pcieport 0000:01:00.0: bridge window [io size 0x2000]:
> failed to assign
> [135630.110245] pcieport 0000:02:02.0: bridge window [mem size 0x00200000
> 64bit pref]: can't assign; no space
> [135630.110249] pcieport 0000:02:02.0: bridge window [mem size 0x00200000
> 64bit pref]: failed to assign
> [135630.110253] pcieport 0000:02:01.0: bridge window [io size 0x1000]:
> can't assign; no space
> [135630.110257] pcieport 0000:02:01.0: bridge window [io size 0x1000]:
> failed to assign
> [135630.110260] pcieport 0000:02:02.0: bridge window [io size 0x1000]:
> can't assign; no space
> [135630.110263] pcieport 0000:02:02.0: bridge window [io size 0x1000]:
> failed to assign
> [135630.110271] pcieport 0000:02:02.0: bridge window [mem size 0x00200000
> 64bit pref]: can't assign; no space
> [135630.110275] pcieport 0000:02:02.0: bridge window [mem size 0x00200000
> 64bit pref]: failed to assign
> [135630.110279] pcieport 0000:02:02.0: bridge window [io size 0x1000]:
> can't assign; no space
> [135630.110282] pcieport 0000:02:02.0: bridge window [io size 0x1000]:
> failed to assign
> [135630.110286] pcieport 0000:02:01.0: bridge window [io size 0x1000]:
> can't assign; no space
> [135630.110289] pcieport 0000:02:01.0: bridge window [io size 0x1000]:
> failed to assign
> [135630.139535] PM: suspend exit
> [135630.211437] hub 3-0:1.0: state 7 ports 2 chg 0002 evt 0000
> [135630.211534] usb usb3-port1: status 0101, change 0000, 12 Mb/s
> [135630.211937] usb usb4-port1: status 0203 change 0011
> [135630.293847] Process accounting resumed
> [135630.319813] hub 4-0:1.0: state 7 ports 2 chg 0002 evt 0000
> [135630.319836] usb usb4-port1: status 0203, change 0000, 10.0 Gb/s
> [135630.339810] usb 3-1: new high-speed USB device number 2 using xhci_hcd
> [135630.497568] usb 3-1: default language 0x0409
> [135630.498182] usb 3-1: udev 2, busnum 3, minor = 257
> [135630.498220] usb 3-1: New USB device found, idVendor=2109,
> idProduct=2817, bcdDevice= 5.e3
> [135630.498252] usb 3-1: New USB device strings: Mfr=1, Product=2,
> SerialNumber=3
> [135630.498254] usb 3-1: Product: USB2.0 Hub
> [135630.498256] usb 3-1: Manufacturer: VIA Labs, Inc.
> [135630.498258] usb 3-1: SerialNumber: 000000000
> [135630.499087] usb 3-1: usb_probe_device
> [135630.499101] usb 3-1: configuration #1 chosen from 1 choice
> [135630.503960] usb 3-1: adding 3-1:1.0 (config #1, interface 0)
> [135630.504782] hub 3-1:1.0: usb_probe_interface
> [135630.504796] hub 3-1:1.0: usb_probe_interface - got id
> [135630.504807] hub 3-1:1.0: USB hub found
> [135630.505081] hub 3-1:1.0: 5 ports detected
> [135630.505094] hub 3-1:1.0: standalone hub
> [135630.505100] hub 3-1:1.0: individual port power switching
> [135630.505107] hub 3-1:1.0: individual port over-current protection
> [135630.509115] hub 3-1:1.0: TT per port
> [135630.509124] hub 3-1:1.0: TT requires at most 32 FS bit times (2664 ns)
> [135630.509130] hub 3-1:1.0: Port indicators are supported
> [135630.509133] hub 3-1:1.0: power on to power good time: 350ms
> [135630.511933] hub 3-1:1.0: local power source is good
> [135630.531819] hub 3-1:1.0: enabling power on all ports
> [135630.655107] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
> [135630.656725] usb 4-1: new SuperSpeed USB device number 2 using xhci_hcd
> [135630.709274] usb 4-1: skipped 1 descriptor after endpoint
> [135630.709452] usb 4-1: default language 0x0409
> [135630.710095] usb 4-1: udev 2, busnum 4, minor = 385
> [135630.710100] usb 4-1: New USB device found, idVendor=2109,
> idProduct=0817, bcdDevice= 5.e3
> [135630.710104] usb 4-1: New USB device strings: Mfr=1, Product=2,
> SerialNumber=3
> [135630.710107] usb 4-1: Product: USB3.0 Hub
> [135630.710110] usb 4-1: Manufacturer: VIA Labs, Inc.
> [135630.710112] usb 4-1: SerialNumber: 000000000
> [135630.710623] usb 4-1: usb_probe_device
> [135630.710629] usb 4-1: configuration #1 chosen from 1 choice
> [135630.711774] usb 4-1: adding 4-1:1.0 (config #1, interface 0)
> [135630.712044] hub 4-1:1.0: usb_probe_interface
> [135630.712049] hub 4-1:1.0: usb_probe_interface - got id
> [135630.712054] hub 4-1:1.0: USB hub found
> [135630.715800] hub 4-1:1.0: 4 ports detected
> [135630.715805] hub 4-1:1.0: standalone hub
> [135630.715807] hub 4-1:1.0: individual port power switching
> [135630.715809] hub 4-1:1.0: individual port over-current protection
> [135630.715811] hub 4-1:1.0: TT requires at most 8 FS bit times (666 ns)
> [135630.715813] hub 4-1:1.0: power on to power good time: 350ms
> [135630.716557] hub 4-1:1.0: local power source is good
> [135630.718147] usb 4-1-port1: peered to 3-1-port1
> [135630.718183] usb 4-1-port2: peered to 3-1-port2
> [135630.718212] usb 4-1-port3: peered to 3-1-port3
> [135630.718233] usb 4-1-port4: peered to 3-1-port4
> [135630.818907] hub 4-1:1.0: enabling power on all ports
> [135630.819762] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
> [135631.039821] usb 3-1-port1: status 0101 change 0001
> [135631.040749] usb 3-1-port5: status 0501 change 0001
> [135631.147824] hub 3-1:1.0: state 7 ports 5 chg 0022 evt 0000
> [135631.148042] usb 3-1-port1: status 0101, change 0000, 12 Mb/s
> [135631.148206] usb 3-1-port1: indicator auto status 0
> [135631.198801] usb 4-1-port1: status 0203 change 0011
> [135631.199751] usb 4-1-port4: status 0203 change 0011
> [135631.275779] usb 3-1.1: new high-speed USB device number 3 using xhci_hcd
> [135631.303781] hub 4-1:1.0: state 7 ports 4 chg 0012 evt 0000
> [135631.326374] usb 4-1-port1: status 0203, change 0000, 5.0 Gb/s
> [135631.425541] usb 3-1.1: default language 0x0409
> [135631.426259] usb 3-1.1: udev 3, busnum 3, minor = 258
> [135631.426263] usb 3-1.1: New USB device found, idVendor=2109,
> idProduct=2817, bcdDevice= 7.b4
> [135631.426266] usb 3-1.1: New USB device strings: Mfr=1, Product=2,
> SerialNumber=3
> [135631.426268] usb 3-1.1: Product: USB2.0 Hub
> [135631.426270] usb 3-1.1: Manufacturer: VIA Labs, Inc.
> [135631.426271] usb 3-1.1: SerialNumber: 000000000
> [135631.426404] usb 3-1.1: usb_probe_device
> [135631.426408] usb 3-1.1: configuration #1 chosen from 1 choice
> [135631.427998] usb 3-1.1: adding 3-1.1:1.0 (config #1, interface 0)
> [135631.428036] hub 3-1.1:1.0: usb_probe_interface
> [135631.428038] hub 3-1.1:1.0: usb_probe_interface - got id
> [135631.428041] hub 3-1.1:1.0: USB hub found
> [135631.428249] hub 3-1.1:1.0: 4 ports detected
> [135631.428251] hub 3-1.1:1.0: standalone hub
> [135631.428252] hub 3-1.1:1.0: individual port power switching
> [135631.428253] hub 3-1.1:1.0: individual port over-current protection
> [135631.429146] hub 3-1.1:1.0: TT per port
> [135631.429149] hub 3-1.1:1.0: TT requires at most 32 FS bit times (2664 ns)
> [135631.429152] hub 3-1.1:1.0: Port indicators are supported
> [135631.429153] hub 3-1.1:1.0: power on to power good time: 350ms
> [135631.429578] hub 3-1.1:1.0: local power source is good
> [135631.429963] hub 3-1.1:1.0: enabling power on all ports
> [135631.521070] usb 4-1.1: new SuperSpeed USB device number 3 using xhci_hcd
> [135631.551487] usb 3-1-port5: status 0501, change 0000, 480 Mb/s
> [135631.551656] usb 3-1-port5: indicator auto status 0
> [135631.579341] usb 4-1.1: skipped 1 descriptor after endpoint
> [135631.579593] usb 4-1.1: default language 0x0409
> [135631.580346] usb 4-1.1: udev 3, busnum 4, minor = 386
> [135631.580348] usb 4-1.1: New USB device found, idVendor=2109,
> idProduct=0817, bcdDevice= 7.b4
> [135631.580351] usb 4-1.1: New USB device strings: Mfr=1, Product=2,
> SerialNumber=3
> [135631.580352] usb 4-1.1: Product: USB3.0 Hub
> [135631.580353] usb 4-1.1: Manufacturer: VIA Labs, Inc.
> [135631.580354] usb 4-1.1: SerialNumber: 000000000
> [135631.580462] usb 4-1.1: usb_probe_device
> [135631.580465] usb 4-1.1: configuration #1 chosen from 1 choice
> [135631.582513] usb 4-1.1: adding 4-1.1:1.0 (config #1, interface 0)
> [135631.582543] hub 4-1.1:1.0: usb_probe_interface
> [135631.582546] hub 4-1.1:1.0: usb_probe_interface - got id
> [135631.582548] hub 4-1.1:1.0: USB hub found
> [135631.582740] hub 4-1.1:1.0: 4 ports detected
> [135631.582742] hub 4-1.1:1.0: standalone hub
> [135631.582744] hub 4-1.1:1.0: individual port power switching
> [135631.582745] hub 4-1.1:1.0: individual port over-current protection
> [135631.582746] hub 4-1.1:1.0: TT requires at most 8 FS bit times (666 ns)
> [135631.582748] hub 4-1.1:1.0: power on to power good time: 350ms
> [135631.583194] hub 4-1.1:1.0: local power source is good
> [135631.583218] usb 4-1.1-port1: peered to 3-1.1-port1
> [135631.583235] usb 4-1.1-port2: peered to 3-1.1-port2
> [135631.583248] usb 4-1.1-port3: peered to 3-1.1-port3
> [135631.583261] usb 4-1.1-port4: peered to 3-1.1-port4
> [135631.655764] usb 3-1.5: new high-speed USB device number 4 using xhci_hcd
> [135631.684088] hub 4-1.1:1.0: enabling power on all ports
> [135631.685155] usb 4-1-port4: status 0203, change 0000, 5.0 Gb/s
> [135631.760364] usb 3-1.5: default language 0x0409
> [135631.760754] usb 3-1.5: udev 4, busnum 3, minor = 259
> [135631.760757] usb 3-1.5: New USB device found, idVendor=2109,
> idProduct=8817, bcdDevice= 0.01
> [135631.760759] usb 3-1.5: New USB device strings: Mfr=1, Product=2,
> SerialNumber=3
> [135631.760761] usb 3-1.5: Product: USB Billboard Device
> [135631.760762] usb 3-1.5: Manufacturer: VIA Labs, Inc.
> [135631.760764] usb 3-1.5: SerialNumber: 0000000000000001
> [135631.760864] usb 3-1.5: usb_probe_device
> [135631.760867] usb 3-1.5: configuration #1 chosen from 1 choice
> [135631.761670] usb 3-1.5: adding 3-1.5:1.0 (config #1, interface 0)
> [135631.928390] usb 3-1.1-port3: status 0101 change 0001
> [135631.995776] usb 1-5: usb auto-suspend, wakeup 0
> [135632.039810] hub 3-1.1:1.0: state 7 ports 4 chg 0008 evt 0000
> [135632.040137] usb 3-1.1-port3: status 0101, change 0000, 12 Mb/s
> [135632.040300] usb 3-1.1-port3: indicator auto status 0
> [135632.215784] usb 1-3: usb auto-suspend, wakeup 0
> [135632.495840] usb 1-4: usb auto-suspend, wakeup 1
> [135632.519768] hub 1-0:1.0: hub_suspend
> [135632.523276] usb usb1: bus auto-suspend, wakeup 1
> [135632.523467] xhci_hcd 0000:00:14.0: hcd_pci_runtime_suspend: 0
> [135636.983657] xhci_hcd 0000:39:00.0: Timeout while waiting for setup
> device command
> [135636.983756] usb 4-1.1: kworker/3:1 timed out on ep0in len=0/4
> [135636.984687] hub 4-1.1:1.0: state 7 ports 4 chg 0000 evt 0000
> [135636.984903] hub 4-1.1:1.0: state 7 ports 4 chg 0000 evt 0008
> [135636.985555] hub 4-1.1:1.0: hub_suspend
> [135636.985997] usb 4-1.1: usb auto-suspend, wakeup 1
> [135637.005910] usb 4-1.1: usb auto-resume
> [135637.071744] usb 4-1.1: Waited 0ms for CONNECT
> [135637.071751] usb 4-1.1: finish resume
> [135637.072442] hub 4-1.1:1.0: hub_resume
> [135637.100903] usb 4-1.1-port3: link state change
> [135637.101072] usb 4-1.1-port3: do warm reset, port only
> [135637.160024] usb 4-1.1-port3: not warm reset yet, waiting 50ms
> [135642.359752] xhci_hcd 0000:39:00.0: Timeout while waiting for setup
> device command
> [135642.359904] usb 4-1.1: kworker/1:0 timed out on ep0in len=0/4
> [135642.360403] usb 4-1.1-port3: not warm reset yet, waiting 200ms
> [135642.567550] usb 4-1.4: device not accepting address 4, error -62
> [135642.567787] usb 4-1.1-port3: not warm reset yet, waiting 200ms
> [135642.587834] usb 3-1.1-port3: not reset yet, waiting 10ms
> [135642.608022] usb 3-1.1-port3: not reset yet, waiting 10ms
> [135642.627960] usb 3-1.1-port3: not reset yet, waiting 200ms
> [135642.779575] usb 4-1.1-port3: not warm reset yet, waiting 200ms
> [135642.836010] usb 3-1.1-port3: not reset yet, waiting 200ms
> [135642.987924] usb 4-1.1-port3: not warm reset yet, waiting 200ms
> [135642.989649] usb 4-1.1-port3: not enabled, trying warm reset again...
> [135643.044090] usb 3-1.1-port3: not reset yet, waiting 200ms
> [135643.253218] usb 3-1.1-port3: not reset yet, waiting 200ms
> [135643.254188] hub 3-1.1:1.0: state 7 ports 4 chg 0000 evt 0008
> [135643.254573] usb 3-1.1-port3: status 0100, change 0001, 12 Mb/s
> [135643.254782] usb 3-1.1-port3: indicator auto status 0
> [135643.255501] hub 4-1.1:1.0: state 7 ports 4 chg 0000 evt 0008
> [135643.256309] usb 4-1.1-port3: status 0203, change 0001, 5.0 Gb/s
> [135643.272060] usb 4-1-port4: not reset yet, waiting 10ms
> [135643.292703] usb 4-1-port4: not reset yet, waiting 10ms
> [135643.311459] usb 4-1-port4: not reset yet, waiting 200ms
> [135643.395529] usb 3-1.1-port3: debounce total 100ms stable 100ms status
> 0x100
> [135643.395546] hub 3-1.1:1.0: hub_suspend
> [135643.395900] usb 3-1.1: usb auto-suspend, wakeup 1
> [135643.399598] usb 4-1.1-port3: debounce total 100ms stable 100ms status
> 0x203
> [135648.759590] xhci_hcd 0000:39:00.0: Timeout while waiting for setup
> device command
> [135654.135471] xhci_hcd 0000:39:00.0: Timeout while waiting for setup
> device command
> [135654.343365] usb 4-1.4: device not accepting address 5, error -62
> [135654.343741] usb 4-1-port4: attempt power cycle
> [135654.423462] usb 4-1.1.3: new SuperSpeed USB device number 6 using
> xhci_hcd
> [135654.443569] usb 4-1.1.3: USB quirks for this device: 400
> [135654.443996] usb 4-1.1.3: skipped 1 descriptor after endpoint
> [135654.444015] usb 4-1.1.3: skipped 1 descriptor after endpoint
> [135654.444026] usb 4-1.1.3: skipped 1 descriptor after endpoint
> [135654.444146] usb 4-1.1.3: skipped 3 descriptors after interface
> [135654.444157] usb 4-1.1.3: skipped 1 descriptor after endpoint
> [135654.444166] usb 4-1.1.3: skipped 1 descriptor after endpoint
> [135654.444174] usb 4-1.1.3: skipped 1 descriptor after endpoint
> [135654.444231] usb 4-1.1.3: default language 0x0409
> [135654.444459] usb 4-1.1.3: udev 6, busnum 4, minor = 389
> [135654.444472] usb 4-1.1.3: New USB device found, idVendor=0bda,
> idProduct=8153, bcdDevice=30.00
> [135654.444485] usb 4-1.1.3: New USB device strings: Mfr=1, Product=2,
> SerialNumber=6
> [135654.444495] usb 4-1.1.3: Product: USB 10/100/1000 LAN
> [135654.444503] usb 4-1.1.3: Manufacturer: Realtek
> [135654.444510] usb 4-1.1.3: SerialNumber: 000001
> [135654.444978] r8152-cfgselector 4-1.1.3: usb_probe_device
> [135654.447545] r8152-cfgselector 4-1.1.3: adding 4-1.1.3:1.0 (config #1,
> interface 0)
> [135654.447741] r8152 4-1.1.3:1.0: usb_probe_interface
> [135654.447753] r8152 4-1.1.3:1.0: usb_probe_interface - got id
> [135654.527864] r8152-cfgselector 4-1.1.3: reset SuperSpeed USB device
> number 6 using xhci_hcd
> [135654.547443] r8152-cfgselector 4-1.1.3: USB quirks for this device: 400
> [135654.570025] r8152 4-1.1.3:1.0: load rtl8153a-4 v2 02/07/20 successfully
> [135654.601390] r8152 4-1.1.3:1.0 eth0: v1.12.13
> [135654.602115] hub 4-1.1:1.0: state 7 ports 4 chg 0000 evt 0008
> [135660.535346] xhci_hcd 0000:39:00.0: Timeout while waiting for setup
> device command
> [135665.911069] xhci_hcd 0000:39:00.0: Timeout while waiting for setup
> device command
> [135666.118792] usb 4-1.4: device not accepting address 7, error -62
> [135666.138995] usb 4-1-port4: not reset yet, waiting 10ms
> [135666.158967] usb 4-1-port4: not reset yet, waiting 10ms
> [135666.178919] usb 4-1-port4: not reset yet, waiting 200ms
> [135666.387360] usb 4-1-port4: not reset yet, waiting 200ms
> [135666.595345] usb 4-1-port4: not reset yet, waiting 200ms
> [135666.803419] usb 4-1-port4: not reset yet, waiting 200ms
> [135666.804994] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0010
> [135666.861597] r8152 4-1.1.3:1.0 enx00e04ceabb21: renamed from eth0
> [135666.922339] r8152 4-1.1.3:1.0 enx00e04ceabb21: carrier on
> [135667.321109] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0010
> [135667.321537] usb 4-1-port4: link state change
> [135667.321750] usb 4-1-port4: do warm reset, port only
> [135667.379354] usb 4-1-port4: not warm reset yet, waiting 50ms
> [135667.498936] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0010
> [135667.499385] usb 4-1-port4: status 0203, change 0001, 5.0 Gb/s
> [135667.642781] usb 4-1-port4: debounce total 100ms stable 100ms status
> 0x203
> [135672.822965] xhci_hcd 0000:39:00.0: Timeout while waiting for setup
> device command
> [135678.198866] xhci_hcd 0000:39:00.0: Timeout while waiting for setup
> device command
> [135678.406490] usb 4-1.4: device not accepting address 9, error -62
> [135678.430725] usb 4-1-port4: not reset yet, waiting 10ms
> [135678.450736] usb 4-1-port4: not reset yet, waiting 10ms
> [135678.470466] usb 4-1-port4: not reset yet, waiting 200ms
> [135678.678449] usb 4-1-port4: not reset yet, waiting 200ms
> [135678.890098] usb 4-1-port4: not reset yet, waiting 200ms
> [135679.094465] usb 4-1-port4: not reset yet, waiting 200ms
> [135679.095792] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0010
> [135679.608911] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0010
> [135679.609291] usb 4-1-port4: link state change
> [135679.609623] usb 4-1-port4: do warm reset, port only
> [135679.667019] usb 4-1-port4: not warm reset yet, waiting 50ms
> [135679.727000] usb 4-1-port4: not warm reset yet, waiting 200ms
> [135679.934968] usb 4-1-port4: not warm reset yet, waiting 200ms
> [135680.142806] usb 4-1-port4: not warm reset yet, waiting 200ms
> [135680.350683] usb 4-1-port4: not warm reset yet, waiting 200ms
> [135680.824878] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0010
> [135680.825079] usb 4-1-port4: link state change
> ```
>
> The last part continues until unplugging device, but this might be a
> separate issue, as the Ethernet connection was functional.
>
> So from
>
> [135654.601390] r8152 4-1.1.3:1.0 eth0: v1.12.13
>
> to
>
> [135666.861597] r8152 4-1.1.3:1.0 enx00e04ceabb21: renamed from eth0
>
> it took 12 seconds.
>
> Is that a problem with the laptop or the adapter? And can it be fixed
> somehow?
>
>
> Kind regards,
>
> Paul
>
>
> [1]: https://lmp-adapter.com/product/lmp-usb-c-mini-dock/?attribute_pa_color=silver
> "LMP USB-C mini Dock (P/N 15954)"
>
>
> PS:
>
> ```
> $ usb-devices
>
> T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh=12
> D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
> P: Vendor=1d6b ProdID=0002 Rev=06.08
> S: Manufacturer=Linux 6.8.0-rc5+ xhci-hcd
> S: Product=xHCI Host Controller
> S: SerialNumber=0000:00:14.0
> C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
> I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
> E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
>
> T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
> D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
> P: Vendor=0cf3 ProdID=e300 Rev=00.01
> C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
> I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
> E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
> E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
> E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
> I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
> E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
> E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
>
> T: Bus=01 Lev=01 Prnt=02 Port=03 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
> D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
> P: Vendor=04f3 ProdID=2234 Rev=11.11
> S: Manufacturer=ELAN
> S: Product=Touchscreen
> C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
> I: If#= 0 Alt= 0 #EPs= 2 Cls=03(HID ) Sub=00 Prot=00 Driver=usbhid
> E: Ad=02(O) Atr=03(Int.) MxPS= 32 Ivl=2ms
> E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=1ms
>
> T: Bus=01 Lev=01 Prnt=03 Port=04 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
> D: Ver= 2.01 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
> P: Vendor=0c45 ProdID=670c Rev=56.26
> S: Manufacturer=CN09GTFMLOG008C8B7FWA01
> S: Product=Integrated_Webcam_HD
> C: #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=500mA
> I: If#= 0 Alt= 0 #EPs= 1 Cls=0e(video) Sub=01 Prot=00 Driver=uvcvideo
> E: Ad=83(I) Atr=03(Int.) MxPS= 16 Ivl=4ms
> I: If#= 1 Alt= 0 #EPs= 1 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideo
> E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>
> T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=5000 MxCh= 6
> D: Ver= 3.00 Cls=09(hub ) Sub=00 Prot=03 MxPS= 9 #Cfgs= 1
> P: Vendor=1d6b ProdID=0003 Rev=06.08
> S: Manufacturer=Linux 6.8.0-rc5+ xhci-hcd
> S: Product=xHCI Host Controller
> S: SerialNumber=0000:00:14.0
> C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
> I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
> E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
>
> T: Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 2
> D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
> P: Vendor=1d6b ProdID=0002 Rev=06.08
> S: Manufacturer=Linux 6.8.0-rc5+ xhci-hcd
> S: Product=xHCI Host Controller
> S: SerialNumber=0000:39:00.0
> C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
> I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
> E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
>
> T: Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 5
> D: Ver= 2.10 Cls=09(hub ) Sub=00 Prot=02 MxPS=64 #Cfgs= 1
> P: Vendor=2109 ProdID=2817 Rev=05.e3
> S: Manufacturer=VIA Labs, Inc.
> S: Product=USB2.0 Hub
> S: SerialNumber=000000000
> C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
> I: If#= 0 Alt= 1 #EPs= 1 Cls=09(hub ) Sub=00 Prot=02 Driver=hub
> E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms
>
> T: Bus=03 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 3 Spd=480 MxCh= 4
> D: Ver= 2.10 Cls=09(hub ) Sub=00 Prot=02 MxPS=64 #Cfgs= 1
> P: Vendor=2109 ProdID=2817 Rev=07.b4
> S: Manufacturer=VIA Labs, Inc.
> S: Product=USB2.0 Hub
> S: SerialNumber=000000000
> C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
> I: If#= 0 Alt= 1 #EPs= 1 Cls=09(hub ) Sub=00 Prot=02 Driver=hub
> E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms
>
> T: Bus=03 Lev=02 Prnt=03 Port=04 Cnt=01 Dev#= 5 Spd=480 MxCh= 0
> D: Ver= 2.01 Cls=11(blbrd) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
> P: Vendor=2109 ProdID=8817 Rev=00.01
> S: Manufacturer=VIA Labs, Inc.
> S: Product=USB Billboard Device
> S: SerialNumber=0000000000000001
> C: #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=100mA
> I: If#= 0 Alt= 0 #EPs= 0 Cls=11(blbrd) Sub=00 Prot=00 Driver=(none)
>
> T: Bus=04 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=10000 MxCh= 2
> D: Ver= 3.10 Cls=09(hub ) Sub=00 Prot=03 MxPS= 9 #Cfgs= 1
> P: Vendor=1d6b ProdID=0003 Rev=06.08
> S: Manufacturer=Linux 6.8.0-rc5+ xhci-hcd
> S: Product=xHCI Host Controller
> S: SerialNumber=0000:39:00.0
> C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
> I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
> E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
>
> T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=5000 MxCh= 4
> D: Ver= 3.20 Cls=09(hub ) Sub=00 Prot=03 MxPS= 9 #Cfgs= 1
> P: Vendor=2109 ProdID=0817 Rev=05.e3
> S: Manufacturer=VIA Labs, Inc.
> S: Product=USB3.0 Hub
> S: SerialNumber=000000000
> C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
> I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
> E: Ad=81(I) Atr=13(Int.) MxPS= 2 Ivl=16ms
>
> T: Bus=04 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 3 Spd=5000 MxCh= 4
> D: Ver= 3.20 Cls=09(hub ) Sub=00 Prot=03 MxPS= 9 #Cfgs= 1
> P: Vendor=2109 ProdID=0817 Rev=07.b4
> S: Manufacturer=VIA Labs, Inc.
> S: Product=USB3.0 Hub
> S: SerialNumber=000000000
> C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
> I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
> E: Ad=81(I) Atr=13(Int.) MxPS= 2 Ivl=16ms
>
> T: Bus=04 Lev=03 Prnt=03 Port=02 Cnt=01 Dev#= 5 Spd=5000 MxCh= 0
> D: Ver= 3.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 2
> P: Vendor=0bda ProdID=8153 Rev=30.00
> S: Manufacturer=Realtek
> S: Product=USB 10/100/1000 LAN
> S: SerialNumber=000001
> C: #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr=288mA
> I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=00 Driver=r8152
> E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
> E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
> E: Ad=83(I) Atr=03(Int.) MxPS= 2 Ivl=16ms
>
> T: Bus=04 Lev=02 Prnt=05 Port=03 Cnt=01 Dev#= 4 Spd=5000 MxCh= 0
> D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
> P: Vendor=058f ProdID=8468 Rev=01.00
> S: Manufacturer=Generic
> S: Product=Mass Storage Device
> S: SerialNumber=058F84688461
> C: #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=800mA
> I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
> E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
> E: Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
> ```
--
heikki
On 26.2.2024 11.09, Heikki Krogerus wrote:
> +Mathias
>
> On Sat, Feb 24, 2024 at 08:45:43PM +0100, Paul Menzel wrote:
>> Dear Linux folks,
>>
>>
>> I suspended a Dell XPS 13 9360 with no devices attached into ACPI S3. Then
>> connecting an LMP USB-C mini Dock (P/N 15954) [1] with an Ethernet cable
>> attached to the left USB-C port and resumed the system from ACPI S3. It took
>> 37 seconds, until the link was established.
>>
>> ```
>> [ 0.000000] Linux version 6.8.0-rc5+
..
>> [135636.985555] hub 4-1.1:1.0: hub_suspend
>> [135636.985997] usb 4-1.1: usb auto-suspend, wakeup 1
>> [135637.005910] usb 4-1.1: usb auto-resume
>> [135637.071744] usb 4-1.1: Waited 0ms for CONNECT
>> [135637.071751] usb 4-1.1: finish resume
>> [135637.072442] hub 4-1.1:1.0: hub_resume
>> [135637.100903] usb 4-1.1-port3: link state change
>> [135637.101072] usb 4-1.1-port3: do warm reset, port only
>> [135637.160024] usb 4-1.1-port3: not warm reset yet, waiting 50ms
>> [135642.359752] xhci_hcd 0000:39:00.0: Timeout while waiting for setup
>> device command
>> [135642.359904] usb 4-1.1: kworker/1:0 timed out on ep0in len=0/4
>> [135642.360403] usb 4-1.1-port3: not warm reset yet, waiting 200ms
>> [135642.567550] usb 4-1.4: device not accepting address 4, error -62
>> [135642.567787] usb 4-1.1-port3: not warm reset yet, waiting 200ms
>> [135642.587834] usb 3-1.1-port3: not reset yet, waiting 10ms
>> [135642.608022] usb 3-1.1-port3: not reset yet, waiting 10ms
>> [135642.627960] usb 3-1.1-port3: not reset yet, waiting 200ms
>> [135642.779575] usb 4-1.1-port3: not warm reset yet, waiting 200ms
>> [135642.836010] usb 3-1.1-port3: not reset yet, waiting 200ms
>> [135642.987924] usb 4-1.1-port3: not warm reset yet, waiting 200ms
>> [135642.989649] usb 4-1.1-port3: not enabled, trying warm reset again...
>> [135643.044090] usb 3-1.1-port3: not reset yet, waiting 200ms
>> [135643.253218] usb 3-1.1-port3: not reset yet, waiting 200ms
>> [135643.254188] hub 3-1.1:1.0: state 7 ports 4 chg 0000 evt 0008
>> [135643.254573] usb 3-1.1-port3: status 0100, change 0001, 12 Mb/s
>> [135643.254782] usb 3-1.1-port3: indicator auto status 0
>> [135643.255501] hub 4-1.1:1.0: state 7 ports 4 chg 0000 evt 0008
>> [135643.256309] usb 4-1.1-port3: status 0203, change 0001, 5.0 Gb/s
>> [135643.272060] usb 4-1-port4: not reset yet, waiting 10ms
>> [135643.292703] usb 4-1-port4: not reset yet, waiting 10ms
>> [135643.311459] usb 4-1-port4: not reset yet, waiting 200ms
>> [135643.395529] usb 3-1.1-port3: debounce total 100ms stable 100ms status
>> 0x100
>> [135643.395546] hub 3-1.1:1.0: hub_suspend
>> [135643.395900] usb 3-1.1: usb auto-suspend, wakeup 1
>> [135643.399598] usb 4-1.1-port3: debounce total 100ms stable 100ms status
>> 0x203
>> [135648.759590] xhci_hcd 0000:39:00.0: Timeout while waiting for setup
>> device command
>> [135654.135471] xhci_hcd 0000:39:00.0: Timeout while waiting for setup
>> device command
>> [135654.343365] usb 4-1.4: device not accepting address 5, error -62
>> [135654.343741] usb 4-1-port4: attempt power cycle
>> [135654.423462] usb 4-1.1.3: new SuperSpeed USB device number 6 using
>> xhci_hcd
>> [135654.443569] usb 4-1.1.3: USB quirks for this device: 400
>> [135654.443996] usb 4-1.1.3: skipped 1 descriptor after endpoint
>> [135654.444015] usb 4-1.1.3: skipped 1 descriptor after endpoint
>> [135654.444026] usb 4-1.1.3: skipped 1 descriptor after endpoint
>> [135654.444146] usb 4-1.1.3: skipped 3 descriptors after interface
>> [135654.444157] usb 4-1.1.3: skipped 1 descriptor after endpoint
>> [135654.444166] usb 4-1.1.3: skipped 1 descriptor after endpoint
>> [135654.444174] usb 4-1.1.3: skipped 1 descriptor after endpoint
>> [135654.444231] usb 4-1.1.3: default language 0x0409
>> [135654.444459] usb 4-1.1.3: udev 6, busnum 4, minor = 389
>> [135654.444472] usb 4-1.1.3: New USB device found, idVendor=0bda,
>> idProduct=8153, bcdDevice=30.00
>> [135654.444485] usb 4-1.1.3: New USB device strings: Mfr=1, Product=2,
>> SerialNumber=6
>> [135654.444495] usb 4-1.1.3: Product: USB 10/100/1000 LAN
>> [135654.444503] usb 4-1.1.3: Manufacturer: Realtek
>> [135654.444510] usb 4-1.1.3: SerialNumber: 000001
>> [135654.444978] r8152-cfgselector 4-1.1.3: usb_probe_device
>> [135654.447545] r8152-cfgselector 4-1.1.3: adding 4-1.1.3:1.0 (config #1,
>> interface 0)
>> [135654.447741] r8152 4-1.1.3:1.0: usb_probe_interface
>> [135654.447753] r8152 4-1.1.3:1.0: usb_probe_interface - got id
>> [135654.527864] r8152-cfgselector 4-1.1.3: reset SuperSpeed USB device
>> number 6 using xhci_hcd
>> [135654.547443] r8152-cfgselector 4-1.1.3: USB quirks for this device: 400
>> [135654.570025] r8152 4-1.1.3:1.0: load rtl8153a-4 v2 02/07/20 successfully
>> [135654.601390] r8152 4-1.1.3:1.0 eth0: v1.12.13
>> [135654.602115] hub 4-1.1:1.0: state 7 ports 4 chg 0000 evt 0008
>> [135660.535346] xhci_hcd 0000:39:00.0: Timeout while waiting for setup
>> device command
>> [135665.911069] xhci_hcd 0000:39:00.0: Timeout while waiting for setup
>> device command
>> [135666.118792] usb 4-1.4: device not accepting address 7, error -62
>> [135666.138995] usb 4-1-port4: not reset yet, waiting 10ms
>> [135666.158967] usb 4-1-port4: not reset yet, waiting 10ms
>> [135666.178919] usb 4-1-port4: not reset yet, waiting 200ms
>> [135666.387360] usb 4-1-port4: not reset yet, waiting 200ms
>> [135666.595345] usb 4-1-port4: not reset yet, waiting 200ms
>> [135666.803419] usb 4-1-port4: not reset yet, waiting 200ms
>> [135666.804994] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0010
>> [135666.861597] r8152 4-1.1.3:1.0 enx00e04ceabb21: renamed from eth0
>> [135666.922339] r8152 4-1.1.3:1.0 enx00e04ceabb21: carrier on
..
>> The last part continues until unplugging device, but this might be a
>> separate issue, as the Ethernet connection was functional.
>>
>> So from
>>
>> [135654.601390] r8152 4-1.1.3:1.0 eth0: v1.12.13
>>
>> to
>>
>> [135666.861597] r8152 4-1.1.3:1.0 enx00e04ceabb21: renamed from eth0
>>
>> it took 12 seconds.
>>
>> Is that a problem with the laptop or the adapter? And can it be fixed
>> somehow?
Your dock has a couple usb hubs, the network adapter is behind the second one.
Looks like several of the usb devices have issues enumerating, hub enumerates one
device at a time so enumeration issue on a hub will block enumerating other
devices on that same hub.
In addition to other devices failing it looks like this network adapter
behind 4-1.1-port3 takes a long time to reset as well.
Are there any other usb devices connected to this hub that can be removed?
Does that improve the situation?
Does dock work normally if its connected to a fully running system, (S0)
Also, those extra hub_suspend and hub_resume entries looks suspicious
Thanks
Mathias