From: Archie Pusaka <[email protected]>
There is a possibility that an ACL packet is received before we
receive the HCI connect event for the corresponding handle. If this
happens, we discard the ACL packet.
Rather than just ignoring them, this patch provides a queue for
incoming ACL packet without a handle. The queue is processed when
receiving a HCI connection event. If 2 seconds elapsed without
receiving the HCI connection event, assume something bad happened
and discard the queued packet.
Signed-off-by: Archie Pusaka <[email protected]>
Reviewed-by: Abhishek Pandit-Subedi <[email protected]>
---
include/net/bluetooth/hci_core.h | 8 +++
net/bluetooth/hci_core.c | 84 +++++++++++++++++++++++++++++---
net/bluetooth/hci_event.c | 2 +
3 files changed, 88 insertions(+), 6 deletions(-)
diff --git a/include/net/bluetooth/hci_core.h b/include/net/bluetooth/hci_core.h
index 836dc997ff94..b69ecdd0d15a 100644
--- a/include/net/bluetooth/hci_core.h
+++ b/include/net/bluetooth/hci_core.h
@@ -270,6 +270,9 @@ struct adv_monitor {
/* Default authenticated payload timeout 30s */
#define DEFAULT_AUTH_PAYLOAD_TIMEOUT 0x0bb8
+/* Time to keep ACL packets without a corresponding handle queued (2s) */
+#define PENDING_ACL_TIMEOUT msecs_to_jiffies(2000)
+
struct amp_assoc {
__u16 len;
__u16 offset;
@@ -538,6 +541,9 @@ struct hci_dev {
struct delayed_work rpa_expired;
bdaddr_t rpa;
+ struct delayed_work remove_pending_acl;
+ struct sk_buff_head pending_acl_q;
+
#if IS_ENABLED(CONFIG_BT_LEDS)
struct led_trigger *power_led;
#endif
@@ -1773,6 +1779,8 @@ void hci_le_start_enc(struct hci_conn *conn, __le16 ediv, __le64 rand,
void hci_copy_identity_address(struct hci_dev *hdev, bdaddr_t *bdaddr,
u8 *bdaddr_type);
+void hci_process_pending_acl(struct hci_dev *hdev, struct hci_conn *conn);
+
#define SCO_AIRMODE_MASK 0x0003
#define SCO_AIRMODE_CVSD 0x0000
#define SCO_AIRMODE_TRANSP 0x0003
diff --git a/net/bluetooth/hci_core.c b/net/bluetooth/hci_core.c
index 7959b851cc63..30780242c267 100644
--- a/net/bluetooth/hci_core.c
+++ b/net/bluetooth/hci_core.c
@@ -1786,6 +1786,7 @@ int hci_dev_do_close(struct hci_dev *hdev)
skb_queue_purge(&hdev->rx_q);
skb_queue_purge(&hdev->cmd_q);
skb_queue_purge(&hdev->raw_q);
+ skb_queue_purge(&hdev->pending_acl_q);
/* Drop last sent command */
if (hdev->sent_cmd) {
@@ -3518,6 +3519,78 @@ static int hci_suspend_notifier(struct notifier_block *nb, unsigned long action,
return NOTIFY_STOP;
}
+static void hci_add_pending_acl(struct hci_dev *hdev, struct sk_buff *skb)
+{
+ skb_queue_tail(&hdev->pending_acl_q, skb);
+
+ queue_delayed_work(hdev->workqueue, &hdev->remove_pending_acl,
+ PENDING_ACL_TIMEOUT);
+}
+
+void hci_process_pending_acl(struct hci_dev *hdev, struct hci_conn *conn)
+{
+ struct sk_buff *skb, *tmp;
+ struct hci_acl_hdr *hdr;
+ u16 handle, flags;
+ bool reset_timer = false;
+
+ skb_queue_walk_safe(&hdev->pending_acl_q, skb, tmp) {
+ hdr = (struct hci_acl_hdr *)skb->data;
+ handle = __le16_to_cpu(hdr->handle);
+ flags = hci_flags(handle);
+ handle = hci_handle(handle);
+
+ if (handle != conn->handle)
+ continue;
+
+ __skb_unlink(skb, &hdev->pending_acl_q);
+ skb_pull(skb, HCI_ACL_HDR_SIZE);
+
+ l2cap_recv_acldata(conn, skb, flags);
+ reset_timer = true;
+ }
+
+ if (reset_timer)
+ mod_delayed_work(hdev->workqueue, &hdev->remove_pending_acl,
+ PENDING_ACL_TIMEOUT);
+}
+
+/* Remove the oldest pending ACL, and all pending ACLs with the same handle */
+static void hci_remove_pending_acl(struct work_struct *work)
+{
+ struct hci_dev *hdev;
+ struct sk_buff *skb, *tmp;
+ struct hci_acl_hdr *hdr;
+ u16 handle, oldest_handle;
+
+ hdev = container_of(work, struct hci_dev, remove_pending_acl.work);
+ skb = skb_dequeue(&hdev->pending_acl_q);
+
+ if (!skb)
+ return;
+
+ hdr = (struct hci_acl_hdr *)skb->data;
+ oldest_handle = hci_handle(__le16_to_cpu(hdr->handle));
+ kfree_skb(skb);
+
+ bt_dev_err(hdev, "ACL packet for unknown connection handle %d",
+ oldest_handle);
+
+ skb_queue_walk_safe(&hdev->pending_acl_q, skb, tmp) {
+ hdr = (struct hci_acl_hdr *)skb->data;
+ handle = hci_handle(__le16_to_cpu(hdr->handle));
+
+ if (handle == oldest_handle) {
+ __skb_unlink(skb, &hdev->pending_acl_q);
+ kfree_skb(skb);
+ }
+ }
+
+ if (!skb_queue_empty(&hdev->pending_acl_q))
+ queue_delayed_work(hdev->workqueue, &hdev->remove_pending_acl,
+ PENDING_ACL_TIMEOUT);
+}
+
/* Alloc HCI device */
struct hci_dev *hci_alloc_dev(void)
{
@@ -3610,10 +3683,12 @@ struct hci_dev *hci_alloc_dev(void)
INIT_WORK(&hdev->suspend_prepare, hci_prepare_suspend);
INIT_DELAYED_WORK(&hdev->power_off, hci_power_off);
+ INIT_DELAYED_WORK(&hdev->remove_pending_acl, hci_remove_pending_acl);
skb_queue_head_init(&hdev->rx_q);
skb_queue_head_init(&hdev->cmd_q);
skb_queue_head_init(&hdev->raw_q);
+ skb_queue_head_init(&hdev->pending_acl_q);
init_waitqueue_head(&hdev->req_wait_q);
init_waitqueue_head(&hdev->suspend_wait_q);
@@ -4662,8 +4737,6 @@ static void hci_acldata_packet(struct hci_dev *hdev, struct sk_buff *skb)
struct hci_conn *conn;
__u16 handle, flags;
- skb_pull(skb, HCI_ACL_HDR_SIZE);
-
handle = __le16_to_cpu(hdr->handle);
flags = hci_flags(handle);
handle = hci_handle(handle);
@@ -4678,17 +4751,16 @@ static void hci_acldata_packet(struct hci_dev *hdev, struct sk_buff *skb)
hci_dev_unlock(hdev);
if (conn) {
+ skb_pull(skb, HCI_ACL_HDR_SIZE);
+
hci_conn_enter_active_mode(conn, BT_POWER_FORCE_ACTIVE_OFF);
/* Send to upper protocol */
l2cap_recv_acldata(conn, skb, flags);
return;
} else {
- bt_dev_err(hdev, "ACL packet for unknown connection handle %d",
- handle);
+ hci_add_pending_acl(hdev, skb);
}
-
- kfree_skb(skb);
}
/* SCO data packet */
diff --git a/net/bluetooth/hci_event.c b/net/bluetooth/hci_event.c
index e060fc9ebb18..108c6c102a6a 100644
--- a/net/bluetooth/hci_event.c
+++ b/net/bluetooth/hci_event.c
@@ -2627,6 +2627,8 @@ static void hci_conn_complete_evt(struct hci_dev *hdev, struct sk_buff *skb)
hci_send_cmd(hdev, HCI_OP_CHANGE_CONN_PTYPE, sizeof(cp),
&cp);
}
+
+ hci_process_pending_acl(hdev, conn);
} else {
conn->state = BT_CLOSED;
if (conn->type == ACL_LINK)
--
2.27.0.212.ge8ba1cc988-goog
Hi Marcel,
On Mon, 29 Jun 2020 at 14:40, Marcel Holtmann <[email protected]> wrote:
>
> Hi Archie,
>
> > There is a possibility that an ACL packet is received before we
> > receive the HCI connect event for the corresponding handle. If this
> > happens, we discard the ACL packet.
> >
> > Rather than just ignoring them, this patch provides a queue for
> > incoming ACL packet without a handle. The queue is processed when
> > receiving a HCI connection event. If 2 seconds elapsed without
> > receiving the HCI connection event, assume something bad happened
> > and discard the queued packet.
> >
> > Signed-off-by: Archie Pusaka <[email protected]>
> > Reviewed-by: Abhishek Pandit-Subedi <[email protected]>
>
> so two things up front. I want to hide this behind a HCI_QUIRK_OUT_OF_ORDER_ACL that a transport driver has to set first. Frankly if this kind of out-of-order happens on UART or SDIO transports, then something is obviously going wrong. I have no plan to fix up after a fully serialized transport.
>
> Secondly, if a transport sets HCI_QUIRK_OUT_OF_ORDER_ACL, then I want this off by default. You can enable it via an experimental setting. The reason here is that we have to make it really hard and fail as often as possible so that hardware manufactures and spec writers realize that something is fundamentally broken here.
>
> I have no problem in running the code and complaining loudly in case the quirk has been set. Just injecting the packets can only happen if bluetoothd explicitly enabled it.
Got it.
>
>
> >
> > ---
> >
> > include/net/bluetooth/hci_core.h | 8 +++
> > net/bluetooth/hci_core.c | 84 +++++++++++++++++++++++++++++---
> > net/bluetooth/hci_event.c | 2 +
> > 3 files changed, 88 insertions(+), 6 deletions(-)
> >
> > diff --git a/include/net/bluetooth/hci_core.h b/include/net/bluetooth/hci_core.h
> > index 836dc997ff94..b69ecdd0d15a 100644
> > --- a/include/net/bluetooth/hci_core.h
> > +++ b/include/net/bluetooth/hci_core.h
> > @@ -270,6 +270,9 @@ struct adv_monitor {
> > /* Default authenticated payload timeout 30s */
> > #define DEFAULT_AUTH_PAYLOAD_TIMEOUT 0x0bb8
> >
> > +/* Time to keep ACL packets without a corresponding handle queued (2s) */
> > +#define PENDING_ACL_TIMEOUT msecs_to_jiffies(2000)
> > +
>
> Do we have some btmon traces with timestamps. Isn’t a second enough? Actually 2 seconds is an awful long time.
When this happens in the test lab, the HCI connect event is about
0.002 second behind the first ACL packet. We can change this if
required.
>
> > struct amp_assoc {
> > __u16 len;
> > __u16 offset;
> > @@ -538,6 +541,9 @@ struct hci_dev {
> > struct delayed_work rpa_expired;
> > bdaddr_t rpa;
> >
> > + struct delayed_work remove_pending_acl;
> > + struct sk_buff_head pending_acl_q;
> > +
>
> can we name this ooo_q and move it to the other queues in this struct. Unless we want to add a Kconfig option around it, we don’t need to keep it here.
Ack.
>
> > #if IS_ENABLED(CONFIG_BT_LEDS)
> > struct led_trigger *power_led;
> > #endif
> > @@ -1773,6 +1779,8 @@ void hci_le_start_enc(struct hci_conn *conn, __le16 ediv, __le64 rand,
> > void hci_copy_identity_address(struct hci_dev *hdev, bdaddr_t *bdaddr,
> > u8 *bdaddr_type);
> >
> > +void hci_process_pending_acl(struct hci_dev *hdev, struct hci_conn *conn);
> > +
> > #define SCO_AIRMODE_MASK 0x0003
> > #define SCO_AIRMODE_CVSD 0x0000
> > #define SCO_AIRMODE_TRANSP 0x0003
> > diff --git a/net/bluetooth/hci_core.c b/net/bluetooth/hci_core.c
> > index 7959b851cc63..30780242c267 100644
> > --- a/net/bluetooth/hci_core.c
> > +++ b/net/bluetooth/hci_core.c
> > @@ -1786,6 +1786,7 @@ int hci_dev_do_close(struct hci_dev *hdev)
> > skb_queue_purge(&hdev->rx_q);
> > skb_queue_purge(&hdev->cmd_q);
> > skb_queue_purge(&hdev->raw_q);
> > + skb_queue_purge(&hdev->pending_acl_q);
> >
> > /* Drop last sent command */
> > if (hdev->sent_cmd) {
> > @@ -3518,6 +3519,78 @@ static int hci_suspend_notifier(struct notifier_block *nb, unsigned long action,
> > return NOTIFY_STOP;
> > }
> >
> > +static void hci_add_pending_acl(struct hci_dev *hdev, struct sk_buff *skb)
> > +{
> > + skb_queue_tail(&hdev->pending_acl_q, skb);
> > +
> > + queue_delayed_work(hdev->workqueue, &hdev->remove_pending_acl,
> > + PENDING_ACL_TIMEOUT);
> > +}
> > +
> > +void hci_process_pending_acl(struct hci_dev *hdev, struct hci_conn *conn)
> > +{
> > + struct sk_buff *skb, *tmp;
> > + struct hci_acl_hdr *hdr;
> > + u16 handle, flags;
> > + bool reset_timer = false;
> > +
> > + skb_queue_walk_safe(&hdev->pending_acl_q, skb, tmp) {
> > + hdr = (struct hci_acl_hdr *)skb->data;
> > + handle = __le16_to_cpu(hdr->handle);
> > + flags = hci_flags(handle);
> > + handle = hci_handle(handle);
> > +
> > + if (handle != conn->handle)
> > + continue;
> > +
> > + __skb_unlink(skb, &hdev->pending_acl_q);
> > + skb_pull(skb, HCI_ACL_HDR_SIZE);
> > +
> > + l2cap_recv_acldata(conn, skb, flags);
> > + reset_timer = true;
> > + }
> > +
> > + if (reset_timer)
> > + mod_delayed_work(hdev->workqueue, &hdev->remove_pending_acl,
> > + PENDING_ACL_TIMEOUT);
> > +}
> > +
> > +/* Remove the oldest pending ACL, and all pending ACLs with the same handle */
> > +static void hci_remove_pending_acl(struct work_struct *work)
> > +{
> > + struct hci_dev *hdev;
> > + struct sk_buff *skb, *tmp;
> > + struct hci_acl_hdr *hdr;
> > + u16 handle, oldest_handle;
> > +
> > + hdev = container_of(work, struct hci_dev, remove_pending_acl.work);
> > + skb = skb_dequeue(&hdev->pending_acl_q);
> > +
> > + if (!skb)
> > + return;
> > +
> > + hdr = (struct hci_acl_hdr *)skb->data;
> > + oldest_handle = hci_handle(__le16_to_cpu(hdr->handle));
> > + kfree_skb(skb);
> > +
> > + bt_dev_err(hdev, "ACL packet for unknown connection handle %d",
> > + oldest_handle);
> > +
> > + skb_queue_walk_safe(&hdev->pending_acl_q, skb, tmp) {
> > + hdr = (struct hci_acl_hdr *)skb->data;
> > + handle = hci_handle(__le16_to_cpu(hdr->handle));
> > +
> > + if (handle == oldest_handle) {
> > + __skb_unlink(skb, &hdev->pending_acl_q);
> > + kfree_skb(skb);
> > + }
> > + }
> > +
> > + if (!skb_queue_empty(&hdev->pending_acl_q))
> > + queue_delayed_work(hdev->workqueue, &hdev->remove_pending_acl,
> > + PENDING_ACL_TIMEOUT);
> > +}
> > +
>
> So I am wondering if we make this too complicated. Since generally speaking we can only have a single HCI connect complete anyway at a time. No matter if the controller serializes it for us or we do it for the controller. So hci_conn_add could just process the queue for packets with its handle and then flush it. And it can flush it no matter what since whatever other packets are in the queue, they can not be valid.
>
> That said, we wouldn’t even need to check the packet handles at all. We just needed to flag them as already out-of-order queued once and hand them back into the rx_q at the top. Then the would be processed as usual. Already ooo packets would cause the same error as before if it is for a non-existing handle and others would end up being processed.
>
> For me this means we just need another queue to park the packets until hci_conn_add gets called. I might have missed something, but I am looking for the least invasive option for this and least code duplication.
I'm not aware of the fact that we can only have a single HCI connect
complete event at any time. Is this also true even if two / more
peripherals connect at the same time?
I was under the impression that if we have device A and B both are
connecting to us at the same time, we might receive the packets in
this order:
(1) ACL A
(2) ACL B
(3) HCI conn evt B
(4) HCI conn evt A
Hence the queue and the handle check.
>
> > /* Alloc HCI device */
> > struct hci_dev *hci_alloc_dev(void)
> > {
> > @@ -3610,10 +3683,12 @@ struct hci_dev *hci_alloc_dev(void)
> > INIT_WORK(&hdev->suspend_prepare, hci_prepare_suspend);
> >
> > INIT_DELAYED_WORK(&hdev->power_off, hci_power_off);
> > + INIT_DELAYED_WORK(&hdev->remove_pending_acl, hci_remove_pending_acl);
> >
> > skb_queue_head_init(&hdev->rx_q);
> > skb_queue_head_init(&hdev->cmd_q);
> > skb_queue_head_init(&hdev->raw_q);
> > + skb_queue_head_init(&hdev->pending_acl_q);
> >
> > init_waitqueue_head(&hdev->req_wait_q);
> > init_waitqueue_head(&hdev->suspend_wait_q);
> > @@ -4662,8 +4737,6 @@ static void hci_acldata_packet(struct hci_dev *hdev, struct sk_buff *skb)
> > struct hci_conn *conn;
> > __u16 handle, flags;
> >
> > - skb_pull(skb, HCI_ACL_HDR_SIZE);
> > -
> > handle = __le16_to_cpu(hdr->handle);
> > flags = hci_flags(handle);
> > handle = hci_handle(handle);
> > @@ -4678,17 +4751,16 @@ static void hci_acldata_packet(struct hci_dev *hdev, struct sk_buff *skb)
> > hci_dev_unlock(hdev);
> >
> > if (conn) {
> > + skb_pull(skb, HCI_ACL_HDR_SIZE);
> > +
> > hci_conn_enter_active_mode(conn, BT_POWER_FORCE_ACTIVE_OFF);
> >
> > /* Send to upper protocol */
> > l2cap_recv_acldata(conn, skb, flags);
> > return;
> > } else {
> > - bt_dev_err(hdev, "ACL packet for unknown connection handle %d",
> > - handle);
> > + hci_add_pending_acl(hdev, skb);
>
> So here I want to keep being verbose. If no quirk is set, then this has to stay as an error. In case the quirk is set, then this should still warn that we are queuing up a packet. It is not an expected behavior.
Ack.
>
> > }
> > -
> > - kfree_skb(skb);
> > }
> >
> > /* SCO data packet */
> > diff --git a/net/bluetooth/hci_event.c b/net/bluetooth/hci_event.c
> > index e060fc9ebb18..108c6c102a6a 100644
> > --- a/net/bluetooth/hci_event.c
> > +++ b/net/bluetooth/hci_event.c
> > @@ -2627,6 +2627,8 @@ static void hci_conn_complete_evt(struct hci_dev *hdev, struct sk_buff *skb)
> > hci_send_cmd(hdev, HCI_OP_CHANGE_CONN_PTYPE, sizeof(cp),
> > &cp);
> > }
> > +
> > + hci_process_pending_acl(hdev, conn);
>
> Can we just do this in hci_conn_add() when we create the connection object?
Yes, we can.
>
> > } else {
> > conn->state = BT_CLOSED;
> > if (conn->type == ACL_LINK)
> > --
> > 2.27.0.212.ge8ba1cc988-goog
> >
>
> Regards
>
> Marcel
>
Thanks,
Archie
Hi Archie,
>>> There is a possibility that an ACL packet is received before we
>>> receive the HCI connect event for the corresponding handle. If this
>>> happens, we discard the ACL packet.
>>>
>>> Rather than just ignoring them, this patch provides a queue for
>>> incoming ACL packet without a handle. The queue is processed when
>>> receiving a HCI connection event. If 2 seconds elapsed without
>>> receiving the HCI connection event, assume something bad happened
>>> and discard the queued packet.
>>>
>>> Signed-off-by: Archie Pusaka <[email protected]>
>>> Reviewed-by: Abhishek Pandit-Subedi <[email protected]>
>>
>> so two things up front. I want to hide this behind a HCI_QUIRK_OUT_OF_ORDER_ACL that a transport driver has to set first. Frankly if this kind of out-of-order happens on UART or SDIO transports, then something is obviously going wrong. I have no plan to fix up after a fully serialized transport.
>>
>> Secondly, if a transport sets HCI_QUIRK_OUT_OF_ORDER_ACL, then I want this off by default. You can enable it via an experimental setting. The reason here is that we have to make it really hard and fail as often as possible so that hardware manufactures and spec writers realize that something is fundamentally broken here.
>>
>> I have no problem in running the code and complaining loudly in case the quirk has been set. Just injecting the packets can only happen if bluetoothd explicitly enabled it.
>
> Got it.
>
>>
>>
>>>
>>> ---
>>>
>>> include/net/bluetooth/hci_core.h | 8 +++
>>> net/bluetooth/hci_core.c | 84 +++++++++++++++++++++++++++++---
>>> net/bluetooth/hci_event.c | 2 +
>>> 3 files changed, 88 insertions(+), 6 deletions(-)
>>>
>>> diff --git a/include/net/bluetooth/hci_core.h b/include/net/bluetooth/hci_core.h
>>> index 836dc997ff94..b69ecdd0d15a 100644
>>> --- a/include/net/bluetooth/hci_core.h
>>> +++ b/include/net/bluetooth/hci_core.h
>>> @@ -270,6 +270,9 @@ struct adv_monitor {
>>> /* Default authenticated payload timeout 30s */
>>> #define DEFAULT_AUTH_PAYLOAD_TIMEOUT 0x0bb8
>>>
>>> +/* Time to keep ACL packets without a corresponding handle queued (2s) */
>>> +#define PENDING_ACL_TIMEOUT msecs_to_jiffies(2000)
>>> +
>>
>> Do we have some btmon traces with timestamps. Isn’t a second enough? Actually 2 seconds is an awful long time.
>
> When this happens in the test lab, the HCI connect event is about
> 0.002 second behind the first ACL packet. We can change this if
> required.
>
>>
>>> struct amp_assoc {
>>> __u16 len;
>>> __u16 offset;
>>> @@ -538,6 +541,9 @@ struct hci_dev {
>>> struct delayed_work rpa_expired;
>>> bdaddr_t rpa;
>>>
>>> + struct delayed_work remove_pending_acl;
>>> + struct sk_buff_head pending_acl_q;
>>> +
>>
>> can we name this ooo_q and move it to the other queues in this struct. Unless we want to add a Kconfig option around it, we don’t need to keep it here.
>
> Ack.
>
>>
>>> #if IS_ENABLED(CONFIG_BT_LEDS)
>>> struct led_trigger *power_led;
>>> #endif
>>> @@ -1773,6 +1779,8 @@ void hci_le_start_enc(struct hci_conn *conn, __le16 ediv, __le64 rand,
>>> void hci_copy_identity_address(struct hci_dev *hdev, bdaddr_t *bdaddr,
>>> u8 *bdaddr_type);
>>>
>>> +void hci_process_pending_acl(struct hci_dev *hdev, struct hci_conn *conn);
>>> +
>>> #define SCO_AIRMODE_MASK 0x0003
>>> #define SCO_AIRMODE_CVSD 0x0000
>>> #define SCO_AIRMODE_TRANSP 0x0003
>>> diff --git a/net/bluetooth/hci_core.c b/net/bluetooth/hci_core.c
>>> index 7959b851cc63..30780242c267 100644
>>> --- a/net/bluetooth/hci_core.c
>>> +++ b/net/bluetooth/hci_core.c
>>> @@ -1786,6 +1786,7 @@ int hci_dev_do_close(struct hci_dev *hdev)
>>> skb_queue_purge(&hdev->rx_q);
>>> skb_queue_purge(&hdev->cmd_q);
>>> skb_queue_purge(&hdev->raw_q);
>>> + skb_queue_purge(&hdev->pending_acl_q);
>>>
>>> /* Drop last sent command */
>>> if (hdev->sent_cmd) {
>>> @@ -3518,6 +3519,78 @@ static int hci_suspend_notifier(struct notifier_block *nb, unsigned long action,
>>> return NOTIFY_STOP;
>>> }
>>>
>>> +static void hci_add_pending_acl(struct hci_dev *hdev, struct sk_buff *skb)
>>> +{
>>> + skb_queue_tail(&hdev->pending_acl_q, skb);
>>> +
>>> + queue_delayed_work(hdev->workqueue, &hdev->remove_pending_acl,
>>> + PENDING_ACL_TIMEOUT);
>>> +}
>>> +
>>> +void hci_process_pending_acl(struct hci_dev *hdev, struct hci_conn *conn)
>>> +{
>>> + struct sk_buff *skb, *tmp;
>>> + struct hci_acl_hdr *hdr;
>>> + u16 handle, flags;
>>> + bool reset_timer = false;
>>> +
>>> + skb_queue_walk_safe(&hdev->pending_acl_q, skb, tmp) {
>>> + hdr = (struct hci_acl_hdr *)skb->data;
>>> + handle = __le16_to_cpu(hdr->handle);
>>> + flags = hci_flags(handle);
>>> + handle = hci_handle(handle);
>>> +
>>> + if (handle != conn->handle)
>>> + continue;
>>> +
>>> + __skb_unlink(skb, &hdev->pending_acl_q);
>>> + skb_pull(skb, HCI_ACL_HDR_SIZE);
>>> +
>>> + l2cap_recv_acldata(conn, skb, flags);
>>> + reset_timer = true;
>>> + }
>>> +
>>> + if (reset_timer)
>>> + mod_delayed_work(hdev->workqueue, &hdev->remove_pending_acl,
>>> + PENDING_ACL_TIMEOUT);
>>> +}
>>> +
>>> +/* Remove the oldest pending ACL, and all pending ACLs with the same handle */
>>> +static void hci_remove_pending_acl(struct work_struct *work)
>>> +{
>>> + struct hci_dev *hdev;
>>> + struct sk_buff *skb, *tmp;
>>> + struct hci_acl_hdr *hdr;
>>> + u16 handle, oldest_handle;
>>> +
>>> + hdev = container_of(work, struct hci_dev, remove_pending_acl.work);
>>> + skb = skb_dequeue(&hdev->pending_acl_q);
>>> +
>>> + if (!skb)
>>> + return;
>>> +
>>> + hdr = (struct hci_acl_hdr *)skb->data;
>>> + oldest_handle = hci_handle(__le16_to_cpu(hdr->handle));
>>> + kfree_skb(skb);
>>> +
>>> + bt_dev_err(hdev, "ACL packet for unknown connection handle %d",
>>> + oldest_handle);
>>> +
>>> + skb_queue_walk_safe(&hdev->pending_acl_q, skb, tmp) {
>>> + hdr = (struct hci_acl_hdr *)skb->data;
>>> + handle = hci_handle(__le16_to_cpu(hdr->handle));
>>> +
>>> + if (handle == oldest_handle) {
>>> + __skb_unlink(skb, &hdev->pending_acl_q);
>>> + kfree_skb(skb);
>>> + }
>>> + }
>>> +
>>> + if (!skb_queue_empty(&hdev->pending_acl_q))
>>> + queue_delayed_work(hdev->workqueue, &hdev->remove_pending_acl,
>>> + PENDING_ACL_TIMEOUT);
>>> +}
>>> +
>>
>> So I am wondering if we make this too complicated. Since generally speaking we can only have a single HCI connect complete anyway at a time. No matter if the controller serializes it for us or we do it for the controller. So hci_conn_add could just process the queue for packets with its handle and then flush it. And it can flush it no matter what since whatever other packets are in the queue, they can not be valid.
>>
>> That said, we wouldn’t even need to check the packet handles at all. We just needed to flag them as already out-of-order queued once and hand them back into the rx_q at the top. Then the would be processed as usual. Already ooo packets would cause the same error as before if it is for a non-existing handle and others would end up being processed.
>>
>> For me this means we just need another queue to park the packets until hci_conn_add gets called. I might have missed something, but I am looking for the least invasive option for this and least code duplication.
>
> I'm not aware of the fact that we can only have a single HCI connect
> complete event at any time. Is this also true even if two / more
> peripherals connect at the same time?
> I was under the impression that if we have device A and B both are
> connecting to us at the same time, we might receive the packets in
> this order:
> (1) ACL A
> (2) ACL B
> (3) HCI conn evt B
> (4) HCI conn evt A
> Hence the queue and the handle check.
my reading from the LL state machine is that once the first LL_Connect_Req is processes, the controller moves out of the advertising state. So no other LL_Connect_Req can be processed. So that means that connection attempts are serialized.
Now if you run AE and multiple instances, that might be different, but then again, these instances are also offset in time and so I don’t see how we can get more than one HCI_Connection_Complete event at a time (and with that a leading ACL packet).
Regards
Marcel
Resending in plain text.
On Wed, Jul 15, 2020 at 9:56 AM Alain Michaud <[email protected]> wrote:
>
> Hi Marcel,
>
> Sorry, just got around to this.
>
> On Tue, Jun 30, 2020 at 2:55 AM Marcel Holtmann <[email protected]> wrote:
>>
>> Hi Archie,
>>
>> >>> There is a possibility that an ACL packet is received before we
>> >>> receive the HCI connect event for the corresponding handle. If this
>> >>> happens, we discard the ACL packet.
>> >>>
>> >>> Rather than just ignoring them, this patch provides a queue for
>> >>> incoming ACL packet without a handle. The queue is processed when
>> >>> receiving a HCI connection event. If 2 seconds elapsed without
>> >>> receiving the HCI connection event, assume something bad happened
>> >>> and discard the queued packet.
>> >>>
>> >>> Signed-off-by: Archie Pusaka <[email protected]>
>> >>> Reviewed-by: Abhishek Pandit-Subedi <[email protected]>
>> >>
>> >> so two things up front. I want to hide this behind a HCI_QUIRK_OUT_OF_ORDER_ACL that a transport driver has to set first. Frankly if this kind of out-of-order happens on UART or SDIO transports, then something is obviously going wrong. I have no plan to fix up after a fully serialized transport.
>> >>
>> >> Secondly, if a transport sets HCI_QUIRK_OUT_OF_ORDER_ACL, then I want this off by default. You can enable it via an experimental setting. The reason here is that we have to make it really hard and fail as often as possible so that hardware manufactures and spec writers realize that something is fundamentally broken here.
>
> I don't have any objection to making this explicit enable to non serialized transports. However, I do wonder what the intention is around making this off by default. We already know there is a race condition between the interupt and bulk endpoints over USB, so this can and does happen. Hardware manufaturers can't relly do much about this other than trying to pull the interupt endpoint more often, but that's only a workaround, it can't avoid it all together.
>
> IMO, this seems like a legitimate fix at the host level and I don't see any obvious benefits to hide this fix under an experimental feature and make it more difficult for the customers and system integrators to discover.
>
>>
>> >>
>> >> I have no problem in running the code and complaining loudly in case the quirk has been set. Just injecting the packets can only happen if bluetoothd explicitly enabled it.
>> >
>> > Got it.
>> >
>> >>
>> >>
>> >>>
>> >>> ---
>> >>>
>> >>> include/net/bluetooth/hci_core.h | 8 +++
>> >>> net/bluetooth/hci_core.c | 84 +++++++++++++++++++++++++++++---
>> >>> net/bluetooth/hci_event.c | 2 +
>> >>> 3 files changed, 88 insertions(+), 6 deletions(-)
>> >>>
>> >>> diff --git a/include/net/bluetooth/hci_core.h b/include/net/bluetooth/hci_core.h
>> >>> index 836dc997ff94..b69ecdd0d15a 100644
>> >>> --- a/include/net/bluetooth/hci_core.h
>> >>> +++ b/include/net/bluetooth/hci_core.h
>> >>> @@ -270,6 +270,9 @@ struct adv_monitor {
>> >>> /* Default authenticated payload timeout 30s */
>> >>> #define DEFAULT_AUTH_PAYLOAD_TIMEOUT 0x0bb8
>> >>>
>> >>> +/* Time to keep ACL packets without a corresponding handle queued (2s) */
>> >>> +#define PENDING_ACL_TIMEOUT msecs_to_jiffies(2000)
>> >>> +
>> >>
>> >> Do we have some btmon traces with timestamps. Isn’t a second enough? Actually 2 seconds is an awful long time.
>> >
>> > When this happens in the test lab, the HCI connect event is about
>> > 0.002 second behind the first ACL packet. We can change this if
>> > required.
>> >
>> >>
>> >>> struct amp_assoc {
>> >>> __u16 len;
>> >>> __u16 offset;
>> >>> @@ -538,6 +541,9 @@ struct hci_dev {
>> >>> struct delayed_work rpa_expired;
>> >>> bdaddr_t rpa;
>> >>>
>> >>> + struct delayed_work remove_pending_acl;
>> >>> + struct sk_buff_head pending_acl_q;
>> >>> +
>> >>
>> >> can we name this ooo_q and move it to the other queues in this struct. Unless we want to add a Kconfig option around it, we don’t need to keep it here.
>> >
>> > Ack.
>> >
>> >>
>> >>> #if IS_ENABLED(CONFIG_BT_LEDS)
>> >>> struct led_trigger *power_led;
>> >>> #endif
>> >>> @@ -1773,6 +1779,8 @@ void hci_le_start_enc(struct hci_conn *conn, __le16 ediv, __le64 rand,
>> >>> void hci_copy_identity_address(struct hci_dev *hdev, bdaddr_t *bdaddr,
>> >>> u8 *bdaddr_type);
>> >>>
>> >>> +void hci_process_pending_acl(struct hci_dev *hdev, struct hci_conn *conn);
>> >>> +
>> >>> #define SCO_AIRMODE_MASK 0x0003
>> >>> #define SCO_AIRMODE_CVSD 0x0000
>> >>> #define SCO_AIRMODE_TRANSP 0x0003
>> >>> diff --git a/net/bluetooth/hci_core.c b/net/bluetooth/hci_core.c
>> >>> index 7959b851cc63..30780242c267 100644
>> >>> --- a/net/bluetooth/hci_core.c
>> >>> +++ b/net/bluetooth/hci_core.c
>> >>> @@ -1786,6 +1786,7 @@ int hci_dev_do_close(struct hci_dev *hdev)
>> >>> skb_queue_purge(&hdev->rx_q);
>> >>> skb_queue_purge(&hdev->cmd_q);
>> >>> skb_queue_purge(&hdev->raw_q);
>> >>> + skb_queue_purge(&hdev->pending_acl_q);
>> >>>
>> >>> /* Drop last sent command */
>> >>> if (hdev->sent_cmd) {
>> >>> @@ -3518,6 +3519,78 @@ static int hci_suspend_notifier(struct notifier_block *nb, unsigned long action,
>> >>> return NOTIFY_STOP;
>> >>> }
>> >>>
>> >>> +static void hci_add_pending_acl(struct hci_dev *hdev, struct sk_buff *skb)
>> >>> +{
>> >>> + skb_queue_tail(&hdev->pending_acl_q, skb);
>> >>> +
>> >>> + queue_delayed_work(hdev->workqueue, &hdev->remove_pending_acl,
>> >>> + PENDING_ACL_TIMEOUT);
>> >>> +}
>> >>> +
>> >>> +void hci_process_pending_acl(struct hci_dev *hdev, struct hci_conn *conn)
>> >>> +{
>> >>> + struct sk_buff *skb, *tmp;
>> >>> + struct hci_acl_hdr *hdr;
>> >>> + u16 handle, flags;
>> >>> + bool reset_timer = false;
>> >>> +
>> >>> + skb_queue_walk_safe(&hdev->pending_acl_q, skb, tmp) {
>> >>> + hdr = (struct hci_acl_hdr *)skb->data;
>> >>> + handle = __le16_to_cpu(hdr->handle);
>> >>> + flags = hci_flags(handle);
>> >>> + handle = hci_handle(handle);
>> >>> +
>> >>> + if (handle != conn->handle)
>> >>> + continue;
>> >>> +
>> >>> + __skb_unlink(skb, &hdev->pending_acl_q);
>> >>> + skb_pull(skb, HCI_ACL_HDR_SIZE);
>> >>> +
>> >>> + l2cap_recv_acldata(conn, skb, flags);
>> >>> + reset_timer = true;
>> >>> + }
>> >>> +
>> >>> + if (reset_timer)
>> >>> + mod_delayed_work(hdev->workqueue, &hdev->remove_pending_acl,
>> >>> + PENDING_ACL_TIMEOUT);
>> >>> +}
>> >>> +
>> >>> +/* Remove the oldest pending ACL, and all pending ACLs with the same handle */
>> >>> +static void hci_remove_pending_acl(struct work_struct *work)
>> >>> +{
>> >>> + struct hci_dev *hdev;
>> >>> + struct sk_buff *skb, *tmp;
>> >>> + struct hci_acl_hdr *hdr;
>> >>> + u16 handle, oldest_handle;
>> >>> +
>> >>> + hdev = container_of(work, struct hci_dev, remove_pending_acl.work);
>> >>> + skb = skb_dequeue(&hdev->pending_acl_q);
>> >>> +
>> >>> + if (!skb)
>> >>> + return;
>> >>> +
>> >>> + hdr = (struct hci_acl_hdr *)skb->data;
>> >>> + oldest_handle = hci_handle(__le16_to_cpu(hdr->handle));
>> >>> + kfree_skb(skb);
>> >>> +
>> >>> + bt_dev_err(hdev, "ACL packet for unknown connection handle %d",
>> >>> + oldest_handle);
>> >>> +
>> >>> + skb_queue_walk_safe(&hdev->pending_acl_q, skb, tmp) {
>> >>> + hdr = (struct hci_acl_hdr *)skb->data;
>> >>> + handle = hci_handle(__le16_to_cpu(hdr->handle));
>> >>> +
>> >>> + if (handle == oldest_handle) {
>> >>> + __skb_unlink(skb, &hdev->pending_acl_q);
>> >>> + kfree_skb(skb);
>> >>> + }
>> >>> + }
>> >>> +
>> >>> + if (!skb_queue_empty(&hdev->pending_acl_q))
>> >>> + queue_delayed_work(hdev->workqueue, &hdev->remove_pending_acl,
>> >>> + PENDING_ACL_TIMEOUT);
>> >>> +}
>> >>> +
>> >>
>> >> So I am wondering if we make this too complicated. Since generally speaking we can only have a single HCI connect complete anyway at a time. No matter if the controller serializes it for us or we do it for the controller. So hci_conn_add could just process the queue for packets with its handle and then flush it. And it can flush it no matter what since whatever other packets are in the queue, they can not be valid.
>> >>
>> >> That said, we wouldn’t even need to check the packet handles at all. We just needed to flag them as already out-of-order queued once and hand them back into the rx_q at the top. Then the would be processed as usual. Already ooo packets would cause the same error as before if it is for a non-existing handle and others would end up being processed.
>> >>
>> >> For me this means we just need another queue to park the packets until hci_conn_add gets called. I might have missed something, but I am looking for the least invasive option for this and least code duplication.
>> >
>> > I'm not aware of the fact that we can only have a single HCI connect
>> > complete event at any time. Is this also true even if two / more
>> > peripherals connect at the same time?
>> > I was under the impression that if we have device A and B both are
>> > connecting to us at the same time, we might receive the packets in
>> > this order:
>> > (1) ACL A
>> > (2) ACL B
>> > (3) HCI conn evt B
>> > (4) HCI conn evt A
>> > Hence the queue and the handle check.
>>
>> my reading from the LL state machine is that once the first LL_Connect_Req is processes, the controller moves out of the advertising state. So no other LL_Connect_Req can be processed. So that means that connection attempts are serialized.
>>
>> Now if you run AE and multiple instances, that might be different, but then again, these instances are also offset in time and so I don’t see how we can get more than one HCI_Connection_Complete event at a time (and with that a leading ACL packet).
>>
>> Regards
>>
>> Marcel
>>
>> --
>> You received this message because you are subscribed to the Google Groups "ChromeOS Bluetooth Upstreaming" group.
>> To unsubscribe from this group and stop receiving emails from it, send an email to [email protected].
>> To post to this group, send email to [email protected].
>> To view this discussion on the web visit https://groups.google.com/a/chromium.org/d/msgid/chromeos-bluetooth-upstreaming/7BBB55E0-FBD9-40C0-80D9-D5E7FC9F80D2%40holtmann.org.
Hi Alain,
On Wed, Jul 15, 2020 at 8:10 AM Alain Michaud <[email protected]> wrote:
>
> Resending in plain text.
I've sent a RFC to work out the ordering, that should work out for any
race where it process ACL before Events during a polling interval
(1ms) so I hope that is enough to catch all these races, if that is
not perhaps we could make the interval configurable.
>
> On Wed, Jul 15, 2020 at 9:56 AM Alain Michaud <[email protected]> wrote:
> >
> > Hi Marcel,
> >
> > Sorry, just got around to this.
> >
> > On Tue, Jun 30, 2020 at 2:55 AM Marcel Holtmann <[email protected]> wrote:
> >>
> >> Hi Archie,
> >>
> >> >>> There is a possibility that an ACL packet is received before we
> >> >>> receive the HCI connect event for the corresponding handle. If this
> >> >>> happens, we discard the ACL packet.
> >> >>>
> >> >>> Rather than just ignoring them, this patch provides a queue for
> >> >>> incoming ACL packet without a handle. The queue is processed when
> >> >>> receiving a HCI connection event. If 2 seconds elapsed without
> >> >>> receiving the HCI connection event, assume something bad happened
> >> >>> and discard the queued packet.
> >> >>>
> >> >>> Signed-off-by: Archie Pusaka <[email protected]>
> >> >>> Reviewed-by: Abhishek Pandit-Subedi <[email protected]>
> >> >>
> >> >> so two things up front. I want to hide this behind a HCI_QUIRK_OUT_OF_ORDER_ACL that a transport driver has to set first. Frankly if this kind of out-of-order happens on UART or SDIO transports, then something is obviously going wrong. I have no plan to fix up after a fully serialized transport.
> >> >>
> >> >> Secondly, if a transport sets HCI_QUIRK_OUT_OF_ORDER_ACL, then I want this off by default. You can enable it via an experimental setting. The reason here is that we have to make it really hard and fail as often as possible so that hardware manufactures and spec writers realize that something is fundamentally broken here.
> >
> > I don't have any objection to making this explicit enable to non serialized transports. However, I do wonder what the intention is around making this off by default. We already know there is a race condition between the interupt and bulk endpoints over USB, so this can and does happen. Hardware manufaturers can't relly do much about this other than trying to pull the interupt endpoint more often, but that's only a workaround, it can't avoid it all together.
> >
> > IMO, this seems like a legitimate fix at the host level and I don't see any obvious benefits to hide this fix under an experimental feature and make it more difficult for the customers and system integrators to discover.
> >
> >>
> >> >>
> >> >> I have no problem in running the code and complaining loudly in case the quirk has been set. Just injecting the packets can only happen if bluetoothd explicitly enabled it.
> >> >
> >> > Got it.
> >> >
> >> >>
> >> >>
> >> >>>
> >> >>> ---
> >> >>>
> >> >>> include/net/bluetooth/hci_core.h | 8 +++
> >> >>> net/bluetooth/hci_core.c | 84 +++++++++++++++++++++++++++++---
> >> >>> net/bluetooth/hci_event.c | 2 +
> >> >>> 3 files changed, 88 insertions(+), 6 deletions(-)
> >> >>>
> >> >>> diff --git a/include/net/bluetooth/hci_core.h b/include/net/bluetooth/hci_core.h
> >> >>> index 836dc997ff94..b69ecdd0d15a 100644
> >> >>> --- a/include/net/bluetooth/hci_core.h
> >> >>> +++ b/include/net/bluetooth/hci_core.h
> >> >>> @@ -270,6 +270,9 @@ struct adv_monitor {
> >> >>> /* Default authenticated payload timeout 30s */
> >> >>> #define DEFAULT_AUTH_PAYLOAD_TIMEOUT 0x0bb8
> >> >>>
> >> >>> +/* Time to keep ACL packets without a corresponding handle queued (2s) */
> >> >>> +#define PENDING_ACL_TIMEOUT msecs_to_jiffies(2000)
> >> >>> +
> >> >>
> >> >> Do we have some btmon traces with timestamps. Isn’t a second enough? Actually 2 seconds is an awful long time.
> >> >
> >> > When this happens in the test lab, the HCI connect event is about
> >> > 0.002 second behind the first ACL packet. We can change this if
> >> > required.
> >> >
> >> >>
> >> >>> struct amp_assoc {
> >> >>> __u16 len;
> >> >>> __u16 offset;
> >> >>> @@ -538,6 +541,9 @@ struct hci_dev {
> >> >>> struct delayed_work rpa_expired;
> >> >>> bdaddr_t rpa;
> >> >>>
> >> >>> + struct delayed_work remove_pending_acl;
> >> >>> + struct sk_buff_head pending_acl_q;
> >> >>> +
> >> >>
> >> >> can we name this ooo_q and move it to the other queues in this struct. Unless we want to add a Kconfig option around it, we don’t need to keep it here.
> >> >
> >> > Ack.
> >> >
> >> >>
> >> >>> #if IS_ENABLED(CONFIG_BT_LEDS)
> >> >>> struct led_trigger *power_led;
> >> >>> #endif
> >> >>> @@ -1773,6 +1779,8 @@ void hci_le_start_enc(struct hci_conn *conn, __le16 ediv, __le64 rand,
> >> >>> void hci_copy_identity_address(struct hci_dev *hdev, bdaddr_t *bdaddr,
> >> >>> u8 *bdaddr_type);
> >> >>>
> >> >>> +void hci_process_pending_acl(struct hci_dev *hdev, struct hci_conn *conn);
> >> >>> +
> >> >>> #define SCO_AIRMODE_MASK 0x0003
> >> >>> #define SCO_AIRMODE_CVSD 0x0000
> >> >>> #define SCO_AIRMODE_TRANSP 0x0003
> >> >>> diff --git a/net/bluetooth/hci_core.c b/net/bluetooth/hci_core.c
> >> >>> index 7959b851cc63..30780242c267 100644
> >> >>> --- a/net/bluetooth/hci_core.c
> >> >>> +++ b/net/bluetooth/hci_core.c
> >> >>> @@ -1786,6 +1786,7 @@ int hci_dev_do_close(struct hci_dev *hdev)
> >> >>> skb_queue_purge(&hdev->rx_q);
> >> >>> skb_queue_purge(&hdev->cmd_q);
> >> >>> skb_queue_purge(&hdev->raw_q);
> >> >>> + skb_queue_purge(&hdev->pending_acl_q);
> >> >>>
> >> >>> /* Drop last sent command */
> >> >>> if (hdev->sent_cmd) {
> >> >>> @@ -3518,6 +3519,78 @@ static int hci_suspend_notifier(struct notifier_block *nb, unsigned long action,
> >> >>> return NOTIFY_STOP;
> >> >>> }
> >> >>>
> >> >>> +static void hci_add_pending_acl(struct hci_dev *hdev, struct sk_buff *skb)
> >> >>> +{
> >> >>> + skb_queue_tail(&hdev->pending_acl_q, skb);
> >> >>> +
> >> >>> + queue_delayed_work(hdev->workqueue, &hdev->remove_pending_acl,
> >> >>> + PENDING_ACL_TIMEOUT);
> >> >>> +}
> >> >>> +
> >> >>> +void hci_process_pending_acl(struct hci_dev *hdev, struct hci_conn *conn)
> >> >>> +{
> >> >>> + struct sk_buff *skb, *tmp;
> >> >>> + struct hci_acl_hdr *hdr;
> >> >>> + u16 handle, flags;
> >> >>> + bool reset_timer = false;
> >> >>> +
> >> >>> + skb_queue_walk_safe(&hdev->pending_acl_q, skb, tmp) {
> >> >>> + hdr = (struct hci_acl_hdr *)skb->data;
> >> >>> + handle = __le16_to_cpu(hdr->handle);
> >> >>> + flags = hci_flags(handle);
> >> >>> + handle = hci_handle(handle);
> >> >>> +
> >> >>> + if (handle != conn->handle)
> >> >>> + continue;
> >> >>> +
> >> >>> + __skb_unlink(skb, &hdev->pending_acl_q);
> >> >>> + skb_pull(skb, HCI_ACL_HDR_SIZE);
> >> >>> +
> >> >>> + l2cap_recv_acldata(conn, skb, flags);
> >> >>> + reset_timer = true;
> >> >>> + }
> >> >>> +
> >> >>> + if (reset_timer)
> >> >>> + mod_delayed_work(hdev->workqueue, &hdev->remove_pending_acl,
> >> >>> + PENDING_ACL_TIMEOUT);
> >> >>> +}
> >> >>> +
> >> >>> +/* Remove the oldest pending ACL, and all pending ACLs with the same handle */
> >> >>> +static void hci_remove_pending_acl(struct work_struct *work)
> >> >>> +{
> >> >>> + struct hci_dev *hdev;
> >> >>> + struct sk_buff *skb, *tmp;
> >> >>> + struct hci_acl_hdr *hdr;
> >> >>> + u16 handle, oldest_handle;
> >> >>> +
> >> >>> + hdev = container_of(work, struct hci_dev, remove_pending_acl.work);
> >> >>> + skb = skb_dequeue(&hdev->pending_acl_q);
> >> >>> +
> >> >>> + if (!skb)
> >> >>> + return;
> >> >>> +
> >> >>> + hdr = (struct hci_acl_hdr *)skb->data;
> >> >>> + oldest_handle = hci_handle(__le16_to_cpu(hdr->handle));
> >> >>> + kfree_skb(skb);
> >> >>> +
> >> >>> + bt_dev_err(hdev, "ACL packet for unknown connection handle %d",
> >> >>> + oldest_handle);
> >> >>> +
> >> >>> + skb_queue_walk_safe(&hdev->pending_acl_q, skb, tmp) {
> >> >>> + hdr = (struct hci_acl_hdr *)skb->data;
> >> >>> + handle = hci_handle(__le16_to_cpu(hdr->handle));
> >> >>> +
> >> >>> + if (handle == oldest_handle) {
> >> >>> + __skb_unlink(skb, &hdev->pending_acl_q);
> >> >>> + kfree_skb(skb);
> >> >>> + }
> >> >>> + }
> >> >>> +
> >> >>> + if (!skb_queue_empty(&hdev->pending_acl_q))
> >> >>> + queue_delayed_work(hdev->workqueue, &hdev->remove_pending_acl,
> >> >>> + PENDING_ACL_TIMEOUT);
> >> >>> +}
> >> >>> +
> >> >>
> >> >> So I am wondering if we make this too complicated. Since generally speaking we can only have a single HCI connect complete anyway at a time. No matter if the controller serializes it for us or we do it for the controller. So hci_conn_add could just process the queue for packets with its handle and then flush it. And it can flush it no matter what since whatever other packets are in the queue, they can not be valid.
> >> >>
> >> >> That said, we wouldn’t even need to check the packet handles at all. We just needed to flag them as already out-of-order queued once and hand them back into the rx_q at the top. Then the would be processed as usual. Already ooo packets would cause the same error as before if it is for a non-existing handle and others would end up being processed.
> >> >>
> >> >> For me this means we just need another queue to park the packets until hci_conn_add gets called. I might have missed something, but I am looking for the least invasive option for this and least code duplication.
> >> >
> >> > I'm not aware of the fact that we can only have a single HCI connect
> >> > complete event at any time. Is this also true even if two / more
> >> > peripherals connect at the same time?
> >> > I was under the impression that if we have device A and B both are
> >> > connecting to us at the same time, we might receive the packets in
> >> > this order:
> >> > (1) ACL A
> >> > (2) ACL B
> >> > (3) HCI conn evt B
> >> > (4) HCI conn evt A
> >> > Hence the queue and the handle check.
> >>
> >> my reading from the LL state machine is that once the first LL_Connect_Req is processes, the controller moves out of the advertising state. So no other LL_Connect_Req can be processed. So that means that connection attempts are serialized.
> >>
> >> Now if you run AE and multiple instances, that might be different, but then again, these instances are also offset in time and so I don’t see how we can get more than one HCI_Connection_Complete event at a time (and with that a leading ACL packet).
> >>
> >> Regards
> >>
> >> Marcel
> >>
> >> --
> >> You received this message because you are subscribed to the Google Groups "ChromeOS Bluetooth Upstreaming" group.
> >> To unsubscribe from this group and stop receiving emails from it, send an email to [email protected].
> >> To post to this group, send email to [email protected].
> >> To view this discussion on the web visit https://groups.google.com/a/chromium.org/d/msgid/chromeos-bluetooth-upstreaming/7BBB55E0-FBD9-40C0-80D9-D5E7FC9F80D2%40holtmann.org.
--
Luiz Augusto von Dentz
Hi Marcel,
On Fri, Jul 17, 2020 at 2:51 AM Marcel Holtmann <[email protected]> wrote:
>
> Hi Alain,
>
> > >>> There is a possibility that an ACL packet is received before we
> > >>> receive the HCI connect event for the corresponding handle. If this
> > >>> happens, we discard the ACL packet.
> > >>>
> > >>> Rather than just ignoring them, this patch provides a queue for
> > >>> incoming ACL packet without a handle. The queue is processed when
> > >>> receiving a HCI connection event. If 2 seconds elapsed without
> > >>> receiving the HCI connection event, assume something bad happened
> > >>> and discard the queued packet.
> > >>>
> > >>> Signed-off-by: Archie Pusaka <[email protected]>
> > >>> Reviewed-by: Abhishek Pandit-Subedi <[email protected]>
> > >>
> > >> so two things up front. I want to hide this behind a HCI_QUIRK_OUT_OF_ORDER_ACL that a transport driver has to set first. Frankly if this kind of out-of-order happens on UART or SDIO transports, then something is obviously going wrong. I have no plan to fix up after a fully serialized transport.
> > >>
> > >> Secondly, if a transport sets HCI_QUIRK_OUT_OF_ORDER_ACL, then I want this off by default. You can enable it via an experimental setting. The reason here is that we have to make it really hard and fail as often as possible so that hardware manufactures and spec writers realize that something is fundamentally broken here.
> > I don't have any objection to making this explicit enable to non serialized transports. However, I do wonder what the intention is around making this off by default. We already know there is a race condition between the interupt and bulk endpoints over USB, so this can and does happen. Hardware manufaturers can't relly do much about this other than trying to pull the interupt endpoint more often, but that's only a workaround, it can't avoid it all together.
> >
> > IMO, this seems like a legitimate fix at the host level and I don't see any obvious benefits to hide this fix under an experimental feature and make it more difficult for the customers and system integrators to discover.
>
> the problem is that this is not a fix. It is papering over a hole and at best a workaround with both eyes closed and hoping for the best. I am not looking forward for the first security researcher to figure out that they have a chance to inject an unencrypted packet since we are waiting 2 seconds for the USB transport to get its act together.
I don't think this is the right characterization but I agree, 2
seconds would be too long, it would ideally be no longer than the USB
polling interval diff.
>
> In addition, I think that Luiz attempt to align with the poll intervals inside the USB transport directly is a cleaner and more self-contained approach. It also reduces the window of opportunity for any attacker since we actually align the USB transport specific intervals with each other.
I'll have to look at Luiz's patch and think through if this really
eliminates the problem. If may indeed be a more practical approach to
this problem.
>
> Regards
>
> Marcel
>