This series brings:
- interconnect plumbing
- display setup
for QCM2290/QRB2210 and
- CAN bus controller
- HDMI display
- wifi fw variant name
for QTI RB1
and the necessary bindings changes
Patch 1-2 is for Dmitry/freedreno
Patch 3 for Georgi/icc
Patch 5 for Will/iommu
the rest are for Bjorn/qcom
Signed-off-by: Konrad Dybcio <[email protected]>
---
Changes in v2:
- Fix up the bindings example in "qcm2290-mdss: Use the non-deprecated DSI compat" (krzk)
- Fix up sc7180 & sc7280 DTs as a result of the bindings changes
- Pick up rbs where it makes sense
- Link to v1: https://lore.kernel.org/r/[email protected]
---
Dmitry Baryshkov (1):
arm64: dts: qcom: qrb2210-rb1: add wifi variant property
Konrad Dybcio (11):
dt-bindings: display: msm: qcm2290-mdss: Use the non-deprecated DSI compat
dt-bindings: display: msm: Add reg bus and rotator interconnects
dt-bindings: interconnect: qcom,msm8998-bwmon: Add QCM2290 bwmon instance
dt-bindings: firmware: qcom,scm: Allow interconnect for everyone
iommu/arm-smmu-qcom: Add QCM2290 DPU compatible
arm64: dts: qcom: sc7180: Add the missing MDSS icc path
arm64: dts: qcom: sc7280: Add the missing MDSS icc path
arm64: dts: qcom: qcm2290: Add display nodes
arm64: dts: qcom: qcm2290: Hook up interconnects
arm64: dts: qcom: qrb2210-rb1: Set up HDMI
arm64: dts: qcom: qrb2210-rb1: Enable CAN bus controller
.../bindings/display/msm/mdss-common.yaml | 18 +-
.../bindings/display/msm/qcom,qcm2290-mdss.yaml | 21 +-
.../bindings/display/msm/qcom,sc7180-mdss.yaml | 14 +-
.../bindings/display/msm/qcom,sc7280-mdss.yaml | 14 +-
.../bindings/display/msm/qcom,sm6115-mdss.yaml | 10 +
.../bindings/display/msm/qcom,sm6125-mdss.yaml | 8 +-
.../bindings/display/msm/qcom,sm6350-mdss.yaml | 8 +-
.../bindings/display/msm/qcom,sm6375-mdss.yaml | 8 +-
.../bindings/display/msm/qcom,sm8450-mdss.yaml | 13 +-
.../devicetree/bindings/firmware/qcom,scm.yaml | 15 -
.../bindings/interconnect/qcom,msm8998-bwmon.yaml | 1 +
arch/arm64/boot/dts/qcom/qcm2290.dtsi | 462 +++++++++++++++++++++
arch/arm64/boot/dts/qcom/qrb2210-rb1.dts | 109 +++++
arch/arm64/boot/dts/qcom/sc7180.dtsi | 8 +-
arch/arm64/boot/dts/qcom/sc7280.dtsi | 9 +-
drivers/iommu/arm/arm-smmu/arm-smmu-qcom.c | 1 +
16 files changed, 671 insertions(+), 48 deletions(-)
---
base-commit: 48bbaf8b793e0770798519f8ee1ea2908ff0943a
change-id: 20231125-topic-rb1_feat-dd510532621b
Best regards,
--
Konrad Dybcio <[email protected]>
Every Qualcomm SoC physically has a "CRYPTO0<->DDR" interconnect lane.
Allow this property to be present, no matter the SoC.
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Konrad Dybcio <[email protected]>
---
Documentation/devicetree/bindings/firmware/qcom,scm.yaml | 15 ---------------
1 file changed, 15 deletions(-)
diff --git a/Documentation/devicetree/bindings/firmware/qcom,scm.yaml b/Documentation/devicetree/bindings/firmware/qcom,scm.yaml
index 0613a37a851a..f3a87a8426d0 100644
--- a/Documentation/devicetree/bindings/firmware/qcom,scm.yaml
+++ b/Documentation/devicetree/bindings/firmware/qcom,scm.yaml
@@ -178,21 +178,6 @@ allOf:
minItems: 3
maxItems: 3
- # Interconnects
- - if:
- not:
- properties:
- compatible:
- contains:
- enum:
- - qcom,scm-qdu1000
- - qcom,scm-sc8280xp
- - qcom,scm-sm8450
- - qcom,scm-sm8550
- then:
- properties:
- interconnects: false
-
# Interrupts
- if:
not:
--
2.43.0
Add the required nodes to support display on QCM2290.
Signed-off-by: Konrad Dybcio <[email protected]>
---
arch/arm64/boot/dts/qcom/qcm2290.dtsi | 214 ++++++++++++++++++++++++++++++++++
1 file changed, 214 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/qcm2290.dtsi b/arch/arm64/boot/dts/qcom/qcm2290.dtsi
index d46e591e72b5..a3edc4667cc5 100644
--- a/arch/arm64/boot/dts/qcom/qcm2290.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcm2290.dtsi
@@ -5,6 +5,7 @@
* Based on sm6115.dtsi and previous efforts by Shawn Guo & Loic Poulain.
*/
+#include <dt-bindings/clock/qcom,dispcc-qcm2290.h>
#include <dt-bindings/clock/qcom,gcc-qcm2290.h>
#include <dt-bindings/clock/qcom,rpmcc.h>
#include <dt-bindings/dma/qcom-gpi.h>
@@ -1105,6 +1106,219 @@ usb_dwc3: usb@4e00000 {
};
};
+ mdss: display-subsystem@5e00000 {
+ compatible = "qcom,qcm2290-mdss";
+ reg = <0x0 0x05e00000 0x0 0x1000>;
+ reg-names = "mdss";
+ interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ clocks = <&gcc GCC_DISP_AHB_CLK>,
+ <&gcc GCC_DISP_HF_AXI_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_CLK>;
+ clock-names = "iface",
+ "bus",
+ "core";
+
+ resets = <&dispcc DISP_CC_MDSS_CORE_BCR>;
+
+ power-domains = <&dispcc MDSS_GDSC>;
+
+ iommus = <&apps_smmu 0x420 0x2>,
+ <&apps_smmu 0x421 0x0>;
+
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ status = "disabled";
+
+ mdp: display-controller@5e01000 {
+ compatible = "qcom,qcm2290-dpu";
+ reg = <0x0 0x05e01000 0x0 0x8f000>,
+ <0x0 0x05eb0000 0x0 0x2008>;
+ reg-names = "mdp",
+ "vbif";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <0>;
+
+ clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
+ <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+ clock-names = "bus",
+ "iface",
+ "core",
+ "lut",
+ "vsync";
+
+ operating-points-v2 = <&mdp_opp_table>;
+ power-domains = <&rpmpd QCM2290_VDDCX>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dpu_intf1_out: endpoint {
+ remote-endpoint = <&mdss_dsi0_in>;
+ };
+ };
+ };
+
+ mdp_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-19200000 {
+ opp-hz = /bits/ 64 <19200000>;
+ required-opps = <&rpmpd_opp_min_svs>;
+ };
+
+ opp-192000000 {
+ opp-hz = /bits/ 64 <192000000>;
+ required-opps = <&rpmpd_opp_low_svs>;
+ };
+
+ opp-256000000 {
+ opp-hz = /bits/ 64 <256000000>;
+ required-opps = <&rpmpd_opp_svs>;
+ };
+
+ opp-307200000 {
+ opp-hz = /bits/ 64 <307200000>;
+ required-opps = <&rpmpd_opp_svs_plus>;
+ };
+
+ opp-384000000 {
+ opp-hz = /bits/ 64 <384000000>;
+ required-opps = <&rpmpd_opp_nom>;
+ };
+ };
+ };
+
+ mdss_dsi0: dsi@5e94000 {
+ compatible = "qcom,qcm2290-dsi-ctrl", "qcom,mdss-dsi-ctrl";
+ reg = <0x0 0x05e94000 0x0 0x400>;
+ reg-names = "dsi_ctrl";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <4>;
+
+ clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
+ <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
+ <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
+ <&dispcc DISP_CC_MDSS_ESC0_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&gcc GCC_DISP_HF_AXI_CLK>;
+ clock-names = "byte",
+ "byte_intf",
+ "pixel",
+ "core",
+ "iface",
+ "bus";
+
+ assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>,
+ <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>;
+ assigned-clock-parents = <&mdss_dsi0_phy 0>,
+ <&mdss_dsi0_phy 1>;
+
+ operating-points-v2 = <&dsi_opp_table>;
+ power-domains = <&rpmpd QCM2290_VDDCX>;
+ phys = <&mdss_dsi0_phy>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "disabled";
+
+ dsi_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-19200000 {
+ opp-hz = /bits/ 64 <19200000>;
+ required-opps = <&rpmpd_opp_min_svs>;
+ };
+
+ opp-164000000 {
+ opp-hz = /bits/ 64 <164000000>;
+ required-opps = <&rpmpd_opp_low_svs>;
+ };
+
+ opp-187500000 {
+ opp-hz = /bits/ 64 <187500000>;
+ required-opps = <&rpmpd_opp_svs>;
+ };
+ };
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ mdss_dsi0_in: endpoint {
+ remote-endpoint = <&dpu_intf1_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ mdss_dsi0_out: endpoint {
+ };
+ };
+ };
+ };
+
+ mdss_dsi0_phy: phy@5e94400 {
+ compatible = "qcom,dsi-phy-14nm-2290";
+ reg = <0x0 0x05e94400 0x0 0x100>,
+ <0x0 0x05e94500 0x0 0x300>,
+ <0x0 0x05e94800 0x0 0x188>;
+ reg-names = "dsi_phy",
+ "dsi_phy_lane",
+ "dsi_pll";
+
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&rpmcc RPM_SMD_XO_CLK_SRC>;
+ clock-names = "iface",
+ "ref";
+
+ power-domains = <&rpmpd QCM2290_VDDMX>;
+ required-opps = <&rpmpd_opp_nom>;
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+
+ status = "disabled";
+ };
+ };
+
+ dispcc: clock-controller@5f00000 {
+ compatible = "qcom,qcm2290-dispcc";
+ reg = <0x0 0x05f00000 0x0 0x20000>;
+ clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>,
+ <&rpmcc RPM_SMD_XO_A_CLK_SRC>,
+ <&gcc GCC_DISP_GPLL0_CLK_SRC>,
+ <&gcc GCC_DISP_GPLL0_DIV_CLK_SRC>,
+ <&mdss_dsi0_phy 0>,
+ <&mdss_dsi0_phy 1>;
+ clock-names = "bi_tcxo",
+ "bi_tcxo_ao",
+ "gcc_disp_gpll0_clk_src",
+ "gcc_disp_gpll0_div_clk_src",
+ "dsi0_phy_pll_out_byteclk",
+ "dsi0_phy_pll_out_dsiclk";
+ #power-domain-cells = <1>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
remoteproc_mpss: remoteproc@6080000 {
compatible = "qcom,qcm2290-mpss-pas", "qcom,sm6115-mpss-pas";
reg = <0x0 0x06080000 0x0 0x100>;
--
2.43.0
MDSS, aside from the MDP-MEM path, also requires the CPU-DISP_CFG one.
Failing to provide it may result in register accesses failing and that's
never good.
Add the missing path.
Signed-off-by: Konrad Dybcio <[email protected]>
---
arch/arm64/boot/dts/qcom/sc7280.dtsi | 9 +++++++--
1 file changed, 7 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index 04bf85b0399a..41d327b1f1b6 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -15,6 +15,7 @@
#include <dt-bindings/dma/qcom-gpi.h>
#include <dt-bindings/firmware/qcom,scm.h>
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interconnect/qcom,icc.h>
#include <dt-bindings/interconnect/qcom,osm-l3.h>
#include <dt-bindings/interconnect/qcom,sc7280.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
@@ -3958,8 +3959,12 @@ mdss: display-subsystem@ae00000 {
interrupt-controller;
#interrupt-cells = <1>;
- interconnects = <&mmss_noc MASTER_MDP0 0 &mc_virt SLAVE_EBI1 0>;
- interconnect-names = "mdp0-mem";
+ interconnects = <&mmss_noc MASTER_MDP0 QCOM_ICC_TAG_ALWAYS
+ &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
+ <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
+ &cnoc2 SLAVE_DISPLAY_CFG QCOM_ICC_TAG_ALWAYS>;
+ interconnect-names = "mdp0-mem",
+ "cpu-cfg";
iommus = <&apps_smmu 0x900 0x402>;
--
2.43.0
Add the QCM2290 DPU compatible to clients compatible list, as it also
needs the workarounds.
Signed-off-by: Konrad Dybcio <[email protected]>
---
drivers/iommu/arm/arm-smmu/arm-smmu-qcom.c | 1 +
1 file changed, 1 insertion(+)
diff --git a/drivers/iommu/arm/arm-smmu/arm-smmu-qcom.c b/drivers/iommu/arm/arm-smmu/arm-smmu-qcom.c
index 549ae4dba3a6..aea5e85b20ff 100644
--- a/drivers/iommu/arm/arm-smmu/arm-smmu-qcom.c
+++ b/drivers/iommu/arm/arm-smmu/arm-smmu-qcom.c
@@ -245,6 +245,7 @@ static const struct of_device_id qcom_smmu_client_of_match[] __maybe_unused = {
{ .compatible = "qcom,adreno" },
{ .compatible = "qcom,mdp4" },
{ .compatible = "qcom,mdss" },
+ { .compatible = "qcom,qcm2290-mdss" },
{ .compatible = "qcom,sc7180-mdss" },
{ .compatible = "qcom,sc7180-mss-pil" },
{ .compatible = "qcom,sc7280-mdss" },
--
2.43.0
The "qcom,dsi-ctrl-6g-qcm2290" has been deprecated in commit 0c0f65c6dd44
("dt-bindings: msm: dsi-controller-main: Add compatible strings for every
current SoC"), but the example hasn't been updated to reflect that.
Fix that.
Fixes: 0c0f65c6dd44 ("dt-bindings: msm: dsi-controller-main: Add compatible strings for every current SoC")
Signed-off-by: Konrad Dybcio <[email protected]>
---
.../devicetree/bindings/display/msm/qcom,qcm2290-mdss.yaml | 7 +++++--
1 file changed, 5 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/display/msm/qcom,qcm2290-mdss.yaml b/Documentation/devicetree/bindings/display/msm/qcom,qcm2290-mdss.yaml
index 5ad155612b6c..d71a8e09a798 100644
--- a/Documentation/devicetree/bindings/display/msm/qcom,qcm2290-mdss.yaml
+++ b/Documentation/devicetree/bindings/display/msm/qcom,qcm2290-mdss.yaml
@@ -56,7 +56,9 @@ patternProperties:
properties:
compatible:
- const: qcom,dsi-ctrl-6g-qcm2290
+ items:
+ - const: qcom,qcm2290-dsi-ctrl
+ - const: qcom,mdss-dsi-ctrl
"^phy@[0-9a-f]+$":
type: object
@@ -136,7 +138,8 @@ examples:
};
dsi@5e94000 {
- compatible = "qcom,dsi-ctrl-6g-qcm2290";
+ compatible = "qcom,qcm2290-dsi-ctrl",
+ "qcom,mdss-dsi-ctrl";
reg = <0x05e94000 0x400>;
reg-names = "dsi_ctrl";
--
2.43.0
Add interconnect provider nodes and hook up interconnects to consumer
devices, including bwmon.
Signed-off-by: Konrad Dybcio <[email protected]>
---
arch/arm64/boot/dts/qcom/qcm2290.dtsi | 248 ++++++++++++++++++++++++++++++++++
1 file changed, 248 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/qcm2290.dtsi b/arch/arm64/boot/dts/qcom/qcm2290.dtsi
index a3edc4667cc5..ce04d0acdede 100644
--- a/arch/arm64/boot/dts/qcom/qcm2290.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcm2290.dtsi
@@ -12,6 +12,8 @@
#include <dt-bindings/firmware/qcom,scm.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interconnect/qcom,qcm2290.h>
+#include <dt-bindings/interconnect/qcom,rpm-icc.h>
#include <dt-bindings/power/qcom-rpmpd.h>
/ {
@@ -151,6 +153,8 @@ scm: scm {
clocks = <&rpmcc RPM_SMD_CE1_CLK>;
clock-names = "core";
#reset-cells = <1>;
+ interconnects = <&system_noc MASTER_CRYPTO_CORE0 RPM_ALWAYS_TAG
+ &bimc SLAVE_EBI1 RPM_ALWAYS_TAG>;
};
};
@@ -669,6 +673,33 @@ usb_qmpphy: phy@1615000 {
status = "disabled";
};
+ system_noc: interconnect@1880000 {
+ compatible = "qcom,qcm2290-snoc";
+ reg = <0x0 0x01880000 0x0 0x60200>;
+ #interconnect-cells = <2>;
+
+ qup_virt: interconnect-qup {
+ compatible = "qcom,qcm2290-qup-virt";
+ #interconnect-cells = <2>;
+ };
+
+ mmnrt_virt: interconnect-mmnrt {
+ compatible = "qcom,qcm2290-mmnrt-virt";
+ #interconnect-cells = <2>;
+ };
+
+ mmrt_virt: interconnect-mmrt {
+ compatible = "qcom,qcm2290-mmrt-virt";
+ #interconnect-cells = <2>;
+ };
+ };
+
+ config_noc: interconnect@1900000 {
+ compatible = "qcom,qcm2290-cnoc";
+ reg = <0x0 0x01900000 0x0 0x8200>;
+ #interconnect-cells = <2>;
+ };
+
qfprom@1b44000 {
compatible = "qcom,qcm2290-qfprom", "qcom,qfprom";
reg = <0x0 0x01b44000 0x0 0x3000>;
@@ -681,6 +712,60 @@ qusb2_hstx_trim: hstx-trim@25b {
};
};
+ pmu@1b8e300 {
+ compatible = "qcom,qcm2290-cpu-bwmon", "qcom,sdm845-bwmon";
+ reg = <0x0 0x01b8e300 0x0 0x600>;
+ interrupts = <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>;
+
+ operating-points-v2 = <&cpu_bwmon_opp_table>;
+ interconnects = <&bimc MASTER_APPSS_PROC RPM_ACTIVE_TAG
+ &bimc SLAVE_EBI1 RPM_ACTIVE_TAG>;
+
+ cpu_bwmon_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-0 {
+ opp-peak-kBps = <(200 * 4 * 1000)>;
+ };
+
+ opp-1 {
+ opp-peak-kBps = <(300 * 4 * 1000)>;
+ };
+
+ opp-2 {
+ opp-peak-kBps = <(451 * 4 * 1000)>;
+ };
+
+ opp-3 {
+ opp-peak-kBps = <(547 * 4 * 1000)>;
+ };
+
+ opp-4 {
+ opp-peak-kBps = <(681 * 4 * 1000)>;
+ };
+
+ opp-5 {
+ opp-peak-kBps = <(768 * 4 * 1000)>;
+ };
+
+ opp-6 {
+ opp-peak-kBps = <(1017 * 4 * 1000)>;
+ };
+
+ opp-7 {
+ opp-peak-kBps = <(1353 * 4 * 1000)>;
+ };
+
+ opp-8 {
+ opp-peak-kBps = <(1555 * 4 * 1000)>;
+ };
+
+ opp-9 {
+ opp-peak-kBps = <(1804 * 4 * 1000)>;
+ };
+ };
+ };
+
spmi_bus: spmi@1c40000 {
compatible = "qcom,spmi-pmic-arb";
reg = <0x0 0x01c40000 0x0 0x1100>,
@@ -721,6 +806,12 @@ rng: rng@4453000 {
clock-names = "core";
};
+ bimc: interconnect@4480000 {
+ compatible = "qcom,qcm2290-bimc";
+ reg = <0x0 0x04480000 0x0 0x80000>;
+ #interconnect-cells = <2>;
+ };
+
rpm_msg_ram: sram@45f0000 {
compatible = "qcom,rpm-msg-ram";
reg = <0x0 0x045f0000 0x0 0x7000>;
@@ -756,13 +847,45 @@ sdhc_1: mmc@4744000 {
resets = <&gcc GCC_SDCC1_BCR>;
power-domains = <&rpmpd QCM2290_VDDCX>;
+ operating-points-v2 = <&sdhc1_opp_table>;
iommus = <&apps_smmu 0xc0 0x0>;
+ interconnects = <&system_noc MASTER_SDCC_1 RPM_ALWAYS_TAG
+ &bimc SLAVE_EBI1 RPM_ALWAYS_TAG>,
+ <&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
+ &config_noc SLAVE_SDCC_1 RPM_ALWAYS_TAG>;
+ interconnect-names = "sdhc-ddr",
+ "cpu-sdhc";
qcom,dll-config = <0x000f642c>;
qcom,ddr-config = <0x80040868>;
bus-width = <8>;
status = "disabled";
+
+ sdhc1_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-100000000 {
+ opp-hz = /bits/ 64 <100000000>;
+ required-opps = <&rpmpd_opp_low_svs>;
+ opp-peak-kBps = <250000 133320>;
+ opp-avg-kBps = <102400 65000>;
+ };
+
+ opp-192000000 {
+ opp-hz = /bits/ 64 <192000000>;
+ required-opps = <&rpmpd_opp_low_svs>;
+ opp-peak-kBps = <800000 300000>;
+ opp-avg-kBps = <204800 200000>;
+ };
+
+ opp-384000000 {
+ opp-hz = /bits/ 64 <384000000>;
+ required-opps = <&rpmpd_opp_svs_plus>;
+ opp-peak-kBps = <800000 300000>;
+ opp-avg-kBps = <204800 200000>;
+ };
+ };
};
sdhc_2: mmc@4784000 {
@@ -786,6 +909,12 @@ sdhc_2: mmc@4784000 {
power-domains = <&rpmpd QCM2290_VDDCX>;
operating-points-v2 = <&sdhc2_opp_table>;
iommus = <&apps_smmu 0xa0 0x0>;
+ interconnects = <&system_noc MASTER_SDCC_2 RPM_ALWAYS_TAG
+ &bimc SLAVE_EBI1 RPM_ALWAYS_TAG>,
+ <&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
+ &config_noc SLAVE_SDCC_2 RPM_ALWAYS_TAG>;
+ interconnect-names = "sdhc-ddr",
+ "cpu-sdhc";
qcom,dll-config = <0x0007642c>;
qcom,ddr-config = <0x80040868>;
@@ -799,11 +928,15 @@ sdhc2_opp_table: opp-table {
opp-100000000 {
opp-hz = /bits/ 64 <100000000>;
required-opps = <&rpmpd_opp_low_svs>;
+ opp-peak-kBps = <250000 133320>;
+ opp-avg-kBps = <261438 150000>;
};
opp-202000000 {
opp-hz = /bits/ 64 <202000000>;
required-opps = <&rpmpd_opp_svs_plus>;
+ opp-peak-kBps = <800000 300000>;
+ opp-avg-kBps = <261438 300000>;
};
};
};
@@ -851,6 +984,15 @@ i2c0: i2c@4a80000 {
dmas = <&gpi_dma0 0 0 QCOM_GPI_I2C>,
<&gpi_dma0 1 0 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+ &qup_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+ <&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
+ &config_noc SLAVE_QUP_0 RPM_ALWAYS_TAG>,
+ <&system_noc MASTER_QUP_0 RPM_ALWAYS_TAG
+ &bimc SLAVE_EBI1 RPM_ALWAYS_TAG>;
+ interconnect-names = "qup-core",
+ "qup-config",
+ "qup-memory";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -867,6 +1009,12 @@ spi0: spi@4a80000 {
dmas = <&gpi_dma0 0 0 QCOM_GPI_SPI>,
<&gpi_dma0 1 0 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+ &qup_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+ <&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
+ &config_noc MASTER_APPSS_PROC RPM_ALWAYS_TAG>;
+ interconnect-names = "qup-core",
+ "qup-config";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -880,6 +1028,12 @@ uart0: serial@4a80000 {
clock-names = "se";
pinctrl-0 = <&qup_uart0_default>;
pinctrl-names = "default";
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+ &qup_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+ <&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
+ &config_noc MASTER_APPSS_PROC RPM_ALWAYS_TAG>;
+ interconnect-names = "qup-core",
+ "qup-config";
status = "disabled";
};
@@ -894,6 +1048,15 @@ i2c1: i2c@4a84000 {
dmas = <&gpi_dma0 0 1 QCOM_GPI_I2C>,
<&gpi_dma0 1 1 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+ &qup_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+ <&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
+ &config_noc SLAVE_QUP_0 RPM_ALWAYS_TAG>,
+ <&system_noc MASTER_QUP_0 RPM_ALWAYS_TAG
+ &bimc SLAVE_EBI1 RPM_ALWAYS_TAG>;
+ interconnect-names = "qup-core",
+ "qup-config",
+ "qup-memory";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -910,6 +1073,12 @@ spi1: spi@4a84000 {
dmas = <&gpi_dma0 0 1 QCOM_GPI_SPI>,
<&gpi_dma0 1 1 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+ &qup_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+ <&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
+ &config_noc MASTER_APPSS_PROC RPM_ALWAYS_TAG>;
+ interconnect-names = "qup-core",
+ "qup-config";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -926,6 +1095,15 @@ i2c2: i2c@4a88000 {
dmas = <&gpi_dma0 0 2 QCOM_GPI_I2C>,
<&gpi_dma0 1 2 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+ &qup_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+ <&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
+ &config_noc SLAVE_QUP_0 RPM_ALWAYS_TAG>,
+ <&system_noc MASTER_QUP_0 RPM_ALWAYS_TAG
+ &bimc SLAVE_EBI1 RPM_ALWAYS_TAG>;
+ interconnect-names = "qup-core",
+ "qup-config",
+ "qup-memory";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -942,6 +1120,12 @@ spi2: spi@4a88000 {
dmas = <&gpi_dma0 0 2 QCOM_GPI_SPI>,
<&gpi_dma0 1 2 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+ &qup_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+ <&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
+ &config_noc MASTER_APPSS_PROC RPM_ALWAYS_TAG>;
+ interconnect-names = "qup-core",
+ "qup-config";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -958,6 +1142,15 @@ i2c3: i2c@4a8c000 {
dmas = <&gpi_dma0 0 3 QCOM_GPI_I2C>,
<&gpi_dma0 1 3 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+ &qup_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+ <&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
+ &config_noc SLAVE_QUP_0 RPM_ALWAYS_TAG>,
+ <&system_noc MASTER_QUP_0 RPM_ALWAYS_TAG
+ &bimc SLAVE_EBI1 RPM_ALWAYS_TAG>;
+ interconnect-names = "qup-core",
+ "qup-config",
+ "qup-memory";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -974,6 +1167,12 @@ spi3: spi@4a8c000 {
dmas = <&gpi_dma0 0 3 QCOM_GPI_SPI>,
<&gpi_dma0 1 3 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+ &qup_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+ <&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
+ &config_noc MASTER_APPSS_PROC RPM_ALWAYS_TAG>;
+ interconnect-names = "qup-core",
+ "qup-config";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -990,6 +1189,15 @@ i2c4: i2c@4a90000 {
dmas = <&gpi_dma0 0 4 QCOM_GPI_I2C>,
<&gpi_dma0 1 4 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+ &qup_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+ <&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
+ &config_noc SLAVE_QUP_0 RPM_ALWAYS_TAG>,
+ <&system_noc MASTER_QUP_0 RPM_ALWAYS_TAG
+ &bimc SLAVE_EBI1 RPM_ALWAYS_TAG>;
+ interconnect-names = "qup-core",
+ "qup-config",
+ "qup-memory";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -1006,6 +1214,12 @@ spi4: spi@4a90000 {
dmas = <&gpi_dma0 0 4 QCOM_GPI_SPI>,
<&gpi_dma0 1 4 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+ &qup_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+ <&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
+ &config_noc MASTER_APPSS_PROC RPM_ALWAYS_TAG>;
+ interconnect-names = "qup-core",
+ "qup-config";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -1019,6 +1233,12 @@ uart4: serial@4a90000 {
clock-names = "se";
pinctrl-0 = <&qup_uart4_default>;
pinctrl-names = "default";
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+ &qup_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+ <&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
+ &config_noc MASTER_APPSS_PROC RPM_ALWAYS_TAG>;
+ interconnect-names = "qup-core",
+ "qup-config";
status = "disabled";
};
@@ -1033,6 +1253,15 @@ i2c5: i2c@4a94000 {
dmas = <&gpi_dma0 0 5 QCOM_GPI_I2C>,
<&gpi_dma0 1 5 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+ &qup_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+ <&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
+ &config_noc SLAVE_QUP_0 RPM_ALWAYS_TAG>,
+ <&system_noc MASTER_QUP_0 RPM_ALWAYS_TAG
+ &bimc SLAVE_EBI1 RPM_ALWAYS_TAG>;
+ interconnect-names = "qup-core",
+ "qup-config",
+ "qup-memory";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -1049,6 +1278,12 @@ spi5: spi@4a94000 {
dmas = <&gpi_dma0 0 5 QCOM_GPI_SPI>,
<&gpi_dma0 1 5 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
+ interconnects = <&qup_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+ &qup_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+ <&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
+ &config_noc MASTER_APPSS_PROC RPM_ALWAYS_TAG>;
+ interconnect-names = "qup-core",
+ "qup-config";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -1081,6 +1316,13 @@ usb: usb@4ef8800 {
resets = <&gcc GCC_USB30_PRIM_BCR>;
power-domains = <&gcc GCC_USB30_PRIM_GDSC>;
+ /* TODO: USB<->IPA path */
+ interconnects = <&system_noc MASTER_USB3_0 RPM_ALWAYS_TAG
+ &bimc SLAVE_EBI1 RPM_ALWAYS_TAG>,
+ <&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
+ &config_noc SLAVE_USB3 RPM_ALWAYS_TAG>;
+ interconnect-names = "usb-ddr",
+ "apps-usb";
wakeup-source;
#address-cells = <2>;
@@ -1127,6 +1369,12 @@ mdss: display-subsystem@5e00000 {
iommus = <&apps_smmu 0x420 0x2>,
<&apps_smmu 0x421 0x0>;
+ interconnects = <&mmrt_virt MASTER_MDP0 RPM_ALWAYS_TAG
+ &bimc SLAVE_EBI1 RPM_ALWAYS_TAG>,
+ <&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
+ &config_noc SLAVE_DISPLAY_CFG RPM_ALWAYS_TAG>;
+ interconnect-names = "mdp0-mem",
+ "cpu-cfg";
#address-cells = <2>;
#size-cells = <2>;
--
2.43.0
Add the required nodes to support display output via the HDMI port.
Signed-off-by: Konrad Dybcio <[email protected]>
---
arch/arm64/boot/dts/qcom/qrb2210-rb1.dts | 86 ++++++++++++++++++++++++++++++++
1 file changed, 86 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/qrb2210-rb1.dts b/arch/arm64/boot/dts/qcom/qrb2210-rb1.dts
index 94885b9c21c8..ac6584164058 100644
--- a/arch/arm64/boot/dts/qcom/qrb2210-rb1.dts
+++ b/arch/arm64/boot/dts/qcom/qrb2210-rb1.dts
@@ -40,6 +40,17 @@ key-volume-up {
};
};
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con: endpoint {
+ remote-endpoint = <<9611_out>;
+ };
+ };
+ };
+
leds {
compatible = "gpio-leds";
@@ -158,6 +169,68 @@ vph_pwr: regulator-vph-pwr {
};
};
+&gpi_dma0 {
+ status = "okay";
+};
+
+&i2c2 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ lt9611_codec: hdmi-bridge@2b {
+ compatible = "lontium,lt9611uxc";
+ reg = <0x2b>;
+ interrupts-extended = <&tlmm 46 IRQ_TYPE_EDGE_FALLING>;
+ reset-gpios = <&tlmm 41 GPIO_ACTIVE_HIGH>;
+
+ vdd-supply = <&vreg_hdmi_out_1p2>;
+ vcc-supply = <<9611_3v3>;
+
+ pinctrl-0 = <<9611_irq_pin <9611_rst_pin>;
+ pinctrl-names = "default";
+ #sound-dai-cells = <1>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ lt9611_a: endpoint {
+ remote-endpoint = <&mdss_dsi0_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ lt9611_out: endpoint {
+ remote-endpoint = <&hdmi_con>;
+ };
+ };
+ };
+ };
+};
+
+&mdss {
+ status = "okay";
+};
+
+&mdss_dsi0 {
+ vdda-supply = <&pm2250_l5>;
+ status = "okay";
+};
+
+&mdss_dsi0_out {
+ remote-endpoint = <<9611_a>;
+ data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi0_phy {
+ status = "okay";
+};
+
&pm2250_resin {
linux,code = <KEY_VOLUMEDOWN>;
status = "okay";
@@ -377,6 +450,19 @@ &sdhc_2 {
};
&tlmm {
+ lt9611_rst_pin: lt9611-rst-state {
+ pins = "gpio41";
+ function = "gpio";
+ input-disable;
+ output-high;
+ };
+
+ lt9611_irq_pin: lt9611-irq-state {
+ pins = "gpio46";
+ function = "gpio";
+ bias-disable;
+ };
+
sd_det_in_on: sd-det-in-on-state {
pins = "gpio88";
function = "gpio";
--
2.43.0
From: Dmitry Baryshkov <[email protected]>
The RB1 platform doesn't have board-specific board-id programmed, it uses
generic 0xff. Thus add the property with the 'variant' of the
calibration data.
Note: the driver will check for the calibration data for the following
IDs, so existing board-2.bin files will continue to work.
- 'bus=snoc,qmi-board-id=ff,qmi-chip-id=120,variant=Thundercomm_RB1'
- 'bus=snoc,qmi-board-id=ff,qmi-chip-id=120'
- 'bus=snoc,qmi-board-id=ff'
For the reference, the board is identified by the driver in the
following way:
ath10k_snoc c800000.wifi: qmi chip_id 0x120 chip_family 0x4007 board_id 0xff soc_id 0x40670000
ath10k_snoc c800000.wifi: qmi fw_version 0x337302d3 fw_build_timestamp 2023-01-06 01:50 fw_build_id QC_IMAGE_VERSION_STRING=WLAN.HL.3.3.7.c2-00723-QCAHLSWMTPLZ-1
ath10k_snoc c800000.wifi: wcn3990 hw1.0 target 0x00000008 chip_id 0x00000000 sub 0000:0000
ath10k_snoc c800000.wifi: kconfig debug 0 debugfs 0 tracing 0 dfs 0 testmode 0
ath10k_snoc c800000.wifi: firmware ver api 5 features wowlan,mgmt-tx-by-reference,non-bmi crc32 b3d4b790
ath10k_snoc c800000.wifi: htt-ver 3.114 wmi-op 4 htt-op 3 cal file max-sta 32 raw 0 hwcrypto 1
Signed-off-by: Dmitry Baryshkov <[email protected]>
Reviewed-by: Konrad Dybcio <[email protected]>
---
arch/arm64/boot/dts/qcom/qrb2210-rb1.dts | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm64/boot/dts/qcom/qrb2210-rb1.dts b/arch/arm64/boot/dts/qcom/qrb2210-rb1.dts
index ac597eb3fe9d..bd7bcf803654 100644
--- a/arch/arm64/boot/dts/qcom/qrb2210-rb1.dts
+++ b/arch/arm64/boot/dts/qcom/qrb2210-rb1.dts
@@ -535,6 +535,7 @@ &wifi {
vdd-1.8-xo-supply = <&pm2250_l13>;
vdd-1.3-rfa-supply = <&pm2250_l10>;
vdd-3.3-ch0-supply = <&pm2250_l22>;
+ qcom,ath10k-calibration-variant = "Thundercomm_RB1";
status = "okay";
};
--
2.43.0
Enable the Microchip mcp2518fd hosted on the SPI5 bus.
Signed-off-by: Konrad Dybcio <[email protected]>
---
arch/arm64/boot/dts/qcom/qrb2210-rb1.dts | 22 ++++++++++++++++++++++
1 file changed, 22 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/qrb2210-rb1.dts b/arch/arm64/boot/dts/qcom/qrb2210-rb1.dts
index ac6584164058..ac597eb3fe9d 100644
--- a/arch/arm64/boot/dts/qcom/qrb2210-rb1.dts
+++ b/arch/arm64/boot/dts/qcom/qrb2210-rb1.dts
@@ -23,6 +23,14 @@ chosen {
stdout-path = "serial0:115200n8";
};
+ clocks {
+ clk40M: can-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <40000000>;
+ #clock-cells = <0>;
+ };
+ };
+
gpio-keys {
compatible = "gpio-keys";
label = "gpio-keys";
@@ -449,6 +457,20 @@ &sdhc_2 {
status = "okay";
};
+&spi5 {
+ status = "okay";
+
+ can@0 {
+ compatible = "microchip,mcp2518fd";
+ reg = <0>;
+ interrupts-extended = <&tlmm 39 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&clk40M>;
+ spi-max-frequency = <10000000>;
+ vdd-supply = <&vdc_5v>;
+ xceiver-supply = <&vdc_5v>;
+ };
+};
+
&tlmm {
lt9611_rst_pin: lt9611-rst-state {
pins = "gpio41";
--
2.43.0
MDSS, aside from the MDP-MEM path, also requires the CPU-DISP_CFG one.
Failing to provide it may result in register accesses failing and that's
never good.
Add the missing path.
Signed-off-by: Konrad Dybcio <[email protected]>
---
arch/arm64/boot/dts/qcom/sc7180.dtsi | 8 ++++++--
1 file changed, 6 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi
index 11f353d416b4..9664e42faeb1 100644
--- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
@@ -3100,8 +3100,12 @@ mdss: display-subsystem@ae00000 {
interrupt-controller;
#interrupt-cells = <1>;
- interconnects = <&mmss_noc MASTER_MDP0 0 &mc_virt SLAVE_EBI1 0>;
- interconnect-names = "mdp0-mem";
+ interconnects = <&mmss_noc MASTER_MDP0 QCOM_ICC_TAG_ALWAYS
+ &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
+ <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
+ &config_noc SLAVE_DISPLAY_CFG QCOM_ICC_TAG_ALWAYS>;
+ interconnect-names = "mdp0-mem",
+ "cpu-cfg";
iommus = <&apps_smmu 0x800 0x2>;
--
2.43.0
On 27/11/2023 16:28, Konrad Dybcio wrote:
> The "qcom,dsi-ctrl-6g-qcm2290" has been deprecated in commit 0c0f65c6dd44
> ("dt-bindings: msm: dsi-controller-main: Add compatible strings for every
> current SoC"), but the example hasn't been updated to reflect that.
>
> Fix that.
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Best regards,
Krzysztof
On 27/11/2023 17:28, Konrad Dybcio wrote:
> From: Dmitry Baryshkov <[email protected]>
>
> The RB1 platform doesn't have board-specific board-id programmed, it uses
> generic 0xff. Thus add the property with the 'variant' of the
> calibration data.
>
> Note: the driver will check for the calibration data for the following
> IDs, so existing board-2.bin files will continue to work.
>
> - 'bus=snoc,qmi-board-id=ff,qmi-chip-id=120,variant=Thundercomm_RB1'
> - 'bus=snoc,qmi-board-id=ff,qmi-chip-id=120'
> - 'bus=snoc,qmi-board-id=ff'
>
> For the reference, the board is identified by the driver in the
> following way:
>
> ath10k_snoc c800000.wifi: qmi chip_id 0x120 chip_family 0x4007 board_id 0xff soc_id 0x40670000
> ath10k_snoc c800000.wifi: qmi fw_version 0x337302d3 fw_build_timestamp 2023-01-06 01:50 fw_build_id QC_IMAGE_VERSION_STRING=WLAN.HL.3.3.7.c2-00723-QCAHLSWMTPLZ-1
> ath10k_snoc c800000.wifi: wcn3990 hw1.0 target 0x00000008 chip_id 0x00000000 sub 0000:0000
> ath10k_snoc c800000.wifi: kconfig debug 0 debugfs 0 tracing 0 dfs 0 testmode 0
> ath10k_snoc c800000.wifi: firmware ver api 5 features wowlan,mgmt-tx-by-reference,non-bmi crc32 b3d4b790
> ath10k_snoc c800000.wifi: htt-ver 3.114 wmi-op 4 htt-op 3 cal file max-sta 32 raw 0 hwcrypto 1
>
> Signed-off-by: Dmitry Baryshkov <[email protected]>
> Reviewed-by: Konrad Dybcio <[email protected]>
As you are resending this patch, you should add your S-o-b.
> ---
> arch/arm64/boot/dts/qcom/qrb2210-rb1.dts | 1 +
> 1 file changed, 1 insertion(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/qrb2210-rb1.dts b/arch/arm64/boot/dts/qcom/qrb2210-rb1.dts
> index ac597eb3fe9d..bd7bcf803654 100644
> --- a/arch/arm64/boot/dts/qcom/qrb2210-rb1.dts
> +++ b/arch/arm64/boot/dts/qcom/qrb2210-rb1.dts
> @@ -535,6 +535,7 @@ &wifi {
> vdd-1.8-xo-supply = <&pm2250_l13>;
> vdd-1.3-rfa-supply = <&pm2250_l10>;
> vdd-3.3-ch0-supply = <&pm2250_l22>;
> + qcom,ath10k-calibration-variant = "Thundercomm_RB1";
> status = "okay";
> };
>
>
--
With best wishes
Dmitry
On 27/11/2023 17:28, Konrad Dybcio wrote:
> Add the required nodes to support display output via the HDMI port.
>
> Signed-off-by: Konrad Dybcio <[email protected]>
> ---
> arch/arm64/boot/dts/qcom/qrb2210-rb1.dts | 86 ++++++++++++++++++++++++++++++++
> 1 file changed, 86 insertions(+)
Reviewed-by: Dmitry Baryshkov <[email protected]>
--
With best wishes
Dmitry
On 27/11/2023 17:28, Konrad Dybcio wrote:
> Add interconnect provider nodes and hook up interconnects to consumer
> devices, including bwmon.
>
> Signed-off-by: Konrad Dybcio <[email protected]>
> ---
> arch/arm64/boot/dts/qcom/qcm2290.dtsi | 248 ++++++++++++++++++++++++++++++++++
> 1 file changed, 248 insertions(+)
Reviewed-by: Dmitry Baryshkov <[email protected]>
--
With best wishes
Dmitry
On 27/11/2023 17:28, Konrad Dybcio wrote:
> Add the required nodes to support display on QCM2290.
>
> Signed-off-by: Konrad Dybcio <[email protected]>
> ---
> arch/arm64/boot/dts/qcom/qcm2290.dtsi | 214 ++++++++++++++++++++++++++++++++++
> 1 file changed, 214 insertions(+)
Reviewed-by: Dmitry Baryshkov <[email protected]>
--
With best wishes
Dmitry
On 27/11/2023 17:28, Konrad Dybcio wrote:
> Add the QCM2290 DPU compatible to clients compatible list, as it also
> needs the workarounds.
Nit: MDSS, not DPU compatible
With that fixed:
Reviewed-by: Dmitry Baryshkov <[email protected]>
>
> Signed-off-by: Konrad Dybcio <[email protected]>
> ---
> drivers/iommu/arm/arm-smmu/arm-smmu-qcom.c | 1 +
> 1 file changed, 1 insertion(+)
>
> diff --git a/drivers/iommu/arm/arm-smmu/arm-smmu-qcom.c b/drivers/iommu/arm/arm-smmu/arm-smmu-qcom.c
> index 549ae4dba3a6..aea5e85b20ff 100644
> --- a/drivers/iommu/arm/arm-smmu/arm-smmu-qcom.c
> +++ b/drivers/iommu/arm/arm-smmu/arm-smmu-qcom.c
> @@ -245,6 +245,7 @@ static const struct of_device_id qcom_smmu_client_of_match[] __maybe_unused = {
> { .compatible = "qcom,adreno" },
> { .compatible = "qcom,mdp4" },
> { .compatible = "qcom,mdss" },
> + { .compatible = "qcom,qcm2290-mdss" },
> { .compatible = "qcom,sc7180-mdss" },
> { .compatible = "qcom,sc7180-mss-pil" },
> { .compatible = "qcom,sc7280-mdss" },
>
--
With best wishes
Dmitry