Those three new drivers were missed on the initial conversion
to ReST format. So:
- Rename them to .rst;
- Add them to the hwmon index.rst index;
- add some blank lines at the "Supported systems:" part, in
order to allow Sphinx to properly identify new lines,
suppressing warnings and avoid it to output some random
lines in bold;
- When multiple authors are involved, change the authors
part to a list, in order to avoid adding blank lines.
- adjust the table cells (one of the tables seemed to be
assuming that tab is 4 positions instead of 8) and add
the table markup.
- be sure that the section markups have the same number of
characters as the section title.
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
---
Documentation/hwmon/index.rst | 3 +++
Documentation/hwmon/{ir38064 => ir38064.rst} | 21 ++++++++++++-------
.../hwmon/{isl68137 => isl68137.rst} | 16 ++++++++++----
.../hwmon/{lochnagar => lochnagar.rst} | 7 +++++--
4 files changed, 33 insertions(+), 14 deletions(-)
rename Documentation/hwmon/{ir38064 => ir38064.rst} (76%)
rename Documentation/hwmon/{isl68137 => isl68137.rst} (85%)
rename Documentation/hwmon/{lochnagar => lochnagar.rst} (93%)
diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst
index 893804414510..3fa14fe7b49c 100644
--- a/Documentation/hwmon/index.rst
+++ b/Documentation/hwmon/index.rst
@@ -65,6 +65,8 @@ Hardware Monitoring Kernel Drivers
ina2xx.rst
ina3221.rst
ir35221.rst
+ ir38064.rst
+ isl68137.rst
it87.rst
jc42.rst
k10temp.rst
@@ -86,6 +88,7 @@ Hardware Monitoring Kernel Drivers
lm93.rst
lm95234.rst
lm95245.rst
+ lochnagar.rst
ltc2945.rst
ltc2978.rst
ltc2990.rst
diff --git a/Documentation/hwmon/ir38064 b/Documentation/hwmon/ir38064.rst
similarity index 76%
rename from Documentation/hwmon/ir38064
rename to Documentation/hwmon/ir38064.rst
index 9f218c39bfe6..c455d755a267 100644
--- a/Documentation/hwmon/ir38064
+++ b/Documentation/hwmon/ir38064.rst
@@ -2,15 +2,18 @@ Kernel driver ir38064
=====================
Supported chips:
+
* Infineon IR38064
+
Prefix: 'ir38064'
Addresses scanned: -
+
Datasheet: Publicly available at the Infineon webiste
https://www.infineon.com/dgdl/Infineon-IR38064MTRPBF-DS-v03_07-EN.pdf?fileId=5546d462584d1d4a0158db0d9efb67ca
Authors:
- Maxim Sloyko <[email protected]>
- Patrick Venture <[email protected]>
+ - Maxim Sloyko <[email protected]>
+ - Patrick Venture <[email protected]>
Description
-----------
@@ -26,29 +29,30 @@ devices explicitly.
Sysfs attributes
----------------
+======================= ===========================
curr1_label "iout1"
curr1_input Measured output current
curr1_crit Critical maximum current
curr1_crit_alarm Current critical high alarm
curr1_max Maximum current
-curr1_max_alarm Current high alarm
+curr1_max_alarm Current high alarm
in1_label "vin"
in1_input Measured input voltage
in1_crit Critical maximum input voltage
in1_crit_alarm Input voltage critical high alarm
-in1_min Minimum input voltage
+in1_min Minimum input voltage
in1_min_alarm Input voltage low alarm
in2_label "vout1"
in2_input Measured output voltage
in2_lcrit Critical minimum output voltage
-in2_lcrit_alarm Output voltage critical low alarm
+in2_lcrit_alarm Output voltage critical low alarm
in2_crit Critical maximum output voltage
in2_crit_alarm Output voltage critical high alarm
-in2_max Maximum output voltage
+in2_max Maximum output voltage
in2_max_alarm Output voltage high alarm
-in2_min Minimum output voltage
+in2_min Minimum output voltage
in2_min_alarm Output voltage low alarm
power1_label "pout1"
@@ -58,4 +62,5 @@ temp1_input Measured temperature
temp1_crit Critical high temperature
temp1_crit_alarm Chip temperature critical high alarm
temp1_max Maximum temperature
-temp1_max_alarm Chip temperature high alarm
+temp1_max_alarm Chip temperature high alarm
+======================= ===========================
diff --git a/Documentation/hwmon/isl68137 b/Documentation/hwmon/isl68137.rst
similarity index 85%
rename from Documentation/hwmon/isl68137
rename to Documentation/hwmon/isl68137.rst
index 92e5c5fc5b77..a5a7c8545c9e 100644
--- a/Documentation/hwmon/isl68137
+++ b/Documentation/hwmon/isl68137.rst
@@ -2,16 +2,22 @@ Kernel driver isl68137
======================
Supported chips:
+
* Intersil ISL68137
+
Prefix: 'isl68137'
+
Addresses scanned: -
- Datasheet: Publicly available at the Intersil website
+
+ Datasheet:
+
+ Publicly available at the Intersil website
https://www.intersil.com/content/dam/Intersil/documents/isl6/isl68137.pdf
Authors:
- Maxim Sloyko <[email protected]>
- Robert Lippert <[email protected]>
- Patrick Venture <[email protected]>
+ - Maxim Sloyko <[email protected]>
+ - Robert Lippert <[email protected]>
+ - Patrick Venture <[email protected]>
Description
-----------
@@ -32,6 +38,7 @@ Beyond the normal sysfs pmbus attributes, the driver exposes a control attribute
Additional Sysfs attributes
---------------------------
+======================= ====================================
avs(0|1)_enable Controls the AVS state of each rail.
curr1_label "iin"
@@ -70,3 +77,4 @@ temp[1-3]_crit Critical high temperature
temp[1-3]_crit_alarm Chip temperature critical high alarm
temp[1-3]_max Maximum temperature
temp[1-3]_max_alarm Chip temperature high alarm
+======================= ====================================
diff --git a/Documentation/hwmon/lochnagar b/Documentation/hwmon/lochnagar.rst
similarity index 93%
rename from Documentation/hwmon/lochnagar
rename to Documentation/hwmon/lochnagar.rst
index e9686fb3eb40..1d609c4d18c3 100644
--- a/Documentation/hwmon/lochnagar
+++ b/Documentation/hwmon/lochnagar.rst
@@ -1,5 +1,5 @@
Kernel Driver Lochnagar
-========================
+=======================
Supported systems:
* Cirrus Logic : Lochnagar 2
@@ -21,6 +21,7 @@ by software.
Sysfs attributes
----------------
+======================= =======================================================
temp1_input The Lochnagar board temperature (milliCelsius)
in0_input Measured voltage for DBVDD1 (milliVolts)
in0_label "DBVDD1"
@@ -76,5 +77,7 @@ curr8_label "MICVDD"
power8_average Measured average power for MICVDD (microWatts)
power8_average_interval Power averaging time input valid from 1 to 1708mS
power8_label "MICVDD"
+======================= =======================================================
-Note: It is not possible to measure voltage on the SYSVDD rail.
+Note:
+ It is not possible to measure voltage on the SYSVDD rail.
--
2.20.1
On Thu, 18 Apr 2019, Mauro Carvalho Chehab <[email protected]> wrote:
> Those three new drivers were missed on the initial conversion
> to ReST format. So:
>
> - Rename them to .rst;
> - Add them to the hwmon index.rst index;
> - add some blank lines at the "Supported systems:" part, in
> order to allow Sphinx to properly identify new lines,
> suppressing warnings and avoid it to output some random
> lines in bold;
> - When multiple authors are involved, change the authors
> part to a list, in order to avoid adding blank lines.
> - adjust the table cells (one of the tables seemed to be
> assuming that tab is 4 positions instead of 8) and add
> the table markup.
> - be sure that the section markups have the same number of
> characters as the section title.
>
> Signed-off-by: Mauro Carvalho Chehab <[email protected]>
> ---
> Documentation/hwmon/index.rst | 3 +++
> Documentation/hwmon/{ir38064 => ir38064.rst} | 21 ++++++++++++-------
> .../hwmon/{isl68137 => isl68137.rst} | 16 ++++++++++----
> .../hwmon/{lochnagar => lochnagar.rst} | 7 +++++--
> 4 files changed, 33 insertions(+), 14 deletions(-)
> rename Documentation/hwmon/{ir38064 => ir38064.rst} (76%)
> rename Documentation/hwmon/{isl68137 => isl68137.rst} (85%)
> rename Documentation/hwmon/{lochnagar => lochnagar.rst} (93%)
>
> diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst
> index 893804414510..3fa14fe7b49c 100644
> --- a/Documentation/hwmon/index.rst
> +++ b/Documentation/hwmon/index.rst
> @@ -65,6 +65,8 @@ Hardware Monitoring Kernel Drivers
> ina2xx.rst
> ina3221.rst
> ir35221.rst
> + ir38064.rst
> + isl68137.rst
Didn't notice it on the first patch adding index.rst, but I don't think
it's customary to add .rst suffix to the toctree.
BR,
Jani.
> it87.rst
> jc42.rst
> k10temp.rst
> @@ -86,6 +88,7 @@ Hardware Monitoring Kernel Drivers
> lm93.rst
> lm95234.rst
> lm95245.rst
> + lochnagar.rst
> ltc2945.rst
> ltc2978.rst
> ltc2990.rst
> diff --git a/Documentation/hwmon/ir38064 b/Documentation/hwmon/ir38064.rst
> similarity index 76%
> rename from Documentation/hwmon/ir38064
> rename to Documentation/hwmon/ir38064.rst
> index 9f218c39bfe6..c455d755a267 100644
> --- a/Documentation/hwmon/ir38064
> +++ b/Documentation/hwmon/ir38064.rst
> @@ -2,15 +2,18 @@ Kernel driver ir38064
> =====================
>
> Supported chips:
> +
> * Infineon IR38064
> +
> Prefix: 'ir38064'
> Addresses scanned: -
> +
> Datasheet: Publicly available at the Infineon webiste
> https://www.infineon.com/dgdl/Infineon-IR38064MTRPBF-DS-v03_07-EN.pdf?fileId=5546d462584d1d4a0158db0d9efb67ca
>
> Authors:
> - Maxim Sloyko <[email protected]>
> - Patrick Venture <[email protected]>
> + - Maxim Sloyko <[email protected]>
> + - Patrick Venture <[email protected]>
>
> Description
> -----------
> @@ -26,29 +29,30 @@ devices explicitly.
> Sysfs attributes
> ----------------
>
> +======================= ===========================
> curr1_label "iout1"
> curr1_input Measured output current
> curr1_crit Critical maximum current
> curr1_crit_alarm Current critical high alarm
> curr1_max Maximum current
> -curr1_max_alarm Current high alarm
> +curr1_max_alarm Current high alarm
>
> in1_label "vin"
> in1_input Measured input voltage
> in1_crit Critical maximum input voltage
> in1_crit_alarm Input voltage critical high alarm
> -in1_min Minimum input voltage
> +in1_min Minimum input voltage
> in1_min_alarm Input voltage low alarm
>
> in2_label "vout1"
> in2_input Measured output voltage
> in2_lcrit Critical minimum output voltage
> -in2_lcrit_alarm Output voltage critical low alarm
> +in2_lcrit_alarm Output voltage critical low alarm
> in2_crit Critical maximum output voltage
> in2_crit_alarm Output voltage critical high alarm
> -in2_max Maximum output voltage
> +in2_max Maximum output voltage
> in2_max_alarm Output voltage high alarm
> -in2_min Minimum output voltage
> +in2_min Minimum output voltage
> in2_min_alarm Output voltage low alarm
>
> power1_label "pout1"
> @@ -58,4 +62,5 @@ temp1_input Measured temperature
> temp1_crit Critical high temperature
> temp1_crit_alarm Chip temperature critical high alarm
> temp1_max Maximum temperature
> -temp1_max_alarm Chip temperature high alarm
> +temp1_max_alarm Chip temperature high alarm
> +======================= ===========================
> diff --git a/Documentation/hwmon/isl68137 b/Documentation/hwmon/isl68137.rst
> similarity index 85%
> rename from Documentation/hwmon/isl68137
> rename to Documentation/hwmon/isl68137.rst
> index 92e5c5fc5b77..a5a7c8545c9e 100644
> --- a/Documentation/hwmon/isl68137
> +++ b/Documentation/hwmon/isl68137.rst
> @@ -2,16 +2,22 @@ Kernel driver isl68137
> ======================
>
> Supported chips:
> +
> * Intersil ISL68137
> +
> Prefix: 'isl68137'
> +
> Addresses scanned: -
> - Datasheet: Publicly available at the Intersil website
> +
> + Datasheet:
> +
> + Publicly available at the Intersil website
> https://www.intersil.com/content/dam/Intersil/documents/isl6/isl68137.pdf
>
> Authors:
> - Maxim Sloyko <[email protected]>
> - Robert Lippert <[email protected]>
> - Patrick Venture <[email protected]>
> + - Maxim Sloyko <[email protected]>
> + - Robert Lippert <[email protected]>
> + - Patrick Venture <[email protected]>
>
> Description
> -----------
> @@ -32,6 +38,7 @@ Beyond the normal sysfs pmbus attributes, the driver exposes a control attribute
> Additional Sysfs attributes
> ---------------------------
>
> +======================= ====================================
> avs(0|1)_enable Controls the AVS state of each rail.
>
> curr1_label "iin"
> @@ -70,3 +77,4 @@ temp[1-3]_crit Critical high temperature
> temp[1-3]_crit_alarm Chip temperature critical high alarm
> temp[1-3]_max Maximum temperature
> temp[1-3]_max_alarm Chip temperature high alarm
> +======================= ====================================
> diff --git a/Documentation/hwmon/lochnagar b/Documentation/hwmon/lochnagar.rst
> similarity index 93%
> rename from Documentation/hwmon/lochnagar
> rename to Documentation/hwmon/lochnagar.rst
> index e9686fb3eb40..1d609c4d18c3 100644
> --- a/Documentation/hwmon/lochnagar
> +++ b/Documentation/hwmon/lochnagar.rst
> @@ -1,5 +1,5 @@
> Kernel Driver Lochnagar
> -========================
> +=======================
>
> Supported systems:
> * Cirrus Logic : Lochnagar 2
> @@ -21,6 +21,7 @@ by software.
> Sysfs attributes
> ----------------
>
> +======================= =======================================================
> temp1_input The Lochnagar board temperature (milliCelsius)
> in0_input Measured voltage for DBVDD1 (milliVolts)
> in0_label "DBVDD1"
> @@ -76,5 +77,7 @@ curr8_label "MICVDD"
> power8_average Measured average power for MICVDD (microWatts)
> power8_average_interval Power averaging time input valid from 1 to 1708mS
> power8_label "MICVDD"
> +======================= =======================================================
>
> -Note: It is not possible to measure voltage on the SYSVDD rail.
> +Note:
> + It is not possible to measure voltage on the SYSVDD rail.
--
Jani Nikula, Intel Open Source Graphics Center
Em Thu, 18 Apr 2019 17:42:29 +0300
Jani Nikula <[email protected]> escreveu:
> On Thu, 18 Apr 2019, Mauro Carvalho Chehab <[email protected]> wrote:
> > Those three new drivers were missed on the initial conversion
> > to ReST format. So:
> >
> > - Rename them to .rst;
> > - Add them to the hwmon index.rst index;
> > - add some blank lines at the "Supported systems:" part, in
> > order to allow Sphinx to properly identify new lines,
> > suppressing warnings and avoid it to output some random
> > lines in bold;
> > - When multiple authors are involved, change the authors
> > part to a list, in order to avoid adding blank lines.
> > - adjust the table cells (one of the tables seemed to be
> > assuming that tab is 4 positions instead of 8) and add
> > the table markup.
> > - be sure that the section markups have the same number of
> > characters as the section title.
> >
> > Signed-off-by: Mauro Carvalho Chehab <[email protected]>
> > ---
> > Documentation/hwmon/index.rst | 3 +++
> > Documentation/hwmon/{ir38064 => ir38064.rst} | 21 ++++++++++++-------
> > .../hwmon/{isl68137 => isl68137.rst} | 16 ++++++++++----
> > .../hwmon/{lochnagar => lochnagar.rst} | 7 +++++--
> > 4 files changed, 33 insertions(+), 14 deletions(-)
> > rename Documentation/hwmon/{ir38064 => ir38064.rst} (76%)
> > rename Documentation/hwmon/{isl68137 => isl68137.rst} (85%)
> > rename Documentation/hwmon/{lochnagar => lochnagar.rst} (93%)
> >
> > diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst
> > index 893804414510..3fa14fe7b49c 100644
> > --- a/Documentation/hwmon/index.rst
> > +++ b/Documentation/hwmon/index.rst
> > @@ -65,6 +65,8 @@ Hardware Monitoring Kernel Drivers
> > ina2xx.rst
> > ina3221.rst
> > ir35221.rst
> > + ir38064.rst
> > + isl68137.rst
>
> Didn't notice it on the first patch adding index.rst, but I don't think
> it's customary to add .rst suffix to the toctree.
Provided that all documents are at the same time, I guess it
doesn't matter having a .rst there or not.
Btw, newer versions of Sphinx build can work with other formats
like markdown. I suspect that, if we end mixing markdown documents,
it would be worth having the extension there.
FYI, someone recently added a markdown file at the tree:
commit e453fa60e086786fe89ba15ee8fef80bc2e6ecc3
Author: Sascha Hauer <[email protected]>
Date: Fri Sep 7 14:36:46 2018 +0200
Documentation: ubifs: Add authentication whitepaper
Documentation/filesystems/ubifs-authentication.md
IMO, the best would be to just run pandoc into it and convert
to .rst, than to mix different markup languages.
Thanks,
Mauro
On Thu, 18 Apr 2019, Mauro Carvalho Chehab <[email protected]> wrote:
> Em Thu, 18 Apr 2019 17:42:29 +0300
> Jani Nikula <[email protected]> escreveu:
>
>> On Thu, 18 Apr 2019, Mauro Carvalho Chehab <[email protected]> wrote:
>> > Those three new drivers were missed on the initial conversion
>> > to ReST format. So:
>> >
>> > - Rename them to .rst;
>> > - Add them to the hwmon index.rst index;
>> > - add some blank lines at the "Supported systems:" part, in
>> > order to allow Sphinx to properly identify new lines,
>> > suppressing warnings and avoid it to output some random
>> > lines in bold;
>> > - When multiple authors are involved, change the authors
>> > part to a list, in order to avoid adding blank lines.
>> > - adjust the table cells (one of the tables seemed to be
>> > assuming that tab is 4 positions instead of 8) and add
>> > the table markup.
>> > - be sure that the section markups have the same number of
>> > characters as the section title.
>> >
>> > Signed-off-by: Mauro Carvalho Chehab <[email protected]>
>> > ---
>> > Documentation/hwmon/index.rst | 3 +++
>> > Documentation/hwmon/{ir38064 => ir38064.rst} | 21 ++++++++++++-------
>> > .../hwmon/{isl68137 => isl68137.rst} | 16 ++++++++++----
>> > .../hwmon/{lochnagar => lochnagar.rst} | 7 +++++--
>> > 4 files changed, 33 insertions(+), 14 deletions(-)
>> > rename Documentation/hwmon/{ir38064 => ir38064.rst} (76%)
>> > rename Documentation/hwmon/{isl68137 => isl68137.rst} (85%)
>> > rename Documentation/hwmon/{lochnagar => lochnagar.rst} (93%)
>> >
>> > diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst
>> > index 893804414510..3fa14fe7b49c 100644
>> > --- a/Documentation/hwmon/index.rst
>> > +++ b/Documentation/hwmon/index.rst
>> > @@ -65,6 +65,8 @@ Hardware Monitoring Kernel Drivers
>> > ina2xx.rst
>> > ina3221.rst
>> > ir35221.rst
>> > + ir38064.rst
>> > + isl68137.rst
>>
>> Didn't notice it on the first patch adding index.rst, but I don't think
>> it's customary to add .rst suffix to the toctree.
>
> Provided that all documents are at the same time, I guess it
> doesn't matter having a .rst there or not.
Parse error. No other index.rst has the suffixes.
> Btw, newer versions of Sphinx build can work with other formats
> like markdown. I suspect that, if we end mixing markdown documents,
> it would be worth having the extension there.
>
> FYI, someone recently added a markdown file at the tree:
>
> commit e453fa60e086786fe89ba15ee8fef80bc2e6ecc3
> Author: Sascha Hauer <[email protected]>
> Date: Fri Sep 7 14:36:46 2018 +0200
>
> Documentation: ubifs: Add authentication whitepaper
>
> Documentation/filesystems/ubifs-authentication.md
>
> IMO, the best would be to just run pandoc into it and convert
> to .rst, than to mix different markup languages.
Agreed. I'd rather we keep it all rst.
BR,
Jani.
--
Jani Nikula, Intel Open Source Graphics Center
Em Fri, 19 Apr 2019 13:12:26 +0300
Jani Nikula <[email protected]> escreveu:
> On Thu, 18 Apr 2019, Mauro Carvalho Chehab <[email protected]> wrote:
> > Em Thu, 18 Apr 2019 17:42:29 +0300
> > Jani Nikula <[email protected]> escreveu:
> >
> >> On Thu, 18 Apr 2019, Mauro Carvalho Chehab <[email protected]> wrote:
> >> > Those three new drivers were missed on the initial conversion
> >> > to ReST format. So:
> >> >
> >> > - Rename them to .rst;
> >> > - Add them to the hwmon index.rst index;
> >> > - add some blank lines at the "Supported systems:" part, in
> >> > order to allow Sphinx to properly identify new lines,
> >> > suppressing warnings and avoid it to output some random
> >> > lines in bold;
> >> > - When multiple authors are involved, change the authors
> >> > part to a list, in order to avoid adding blank lines.
> >> > - adjust the table cells (one of the tables seemed to be
> >> > assuming that tab is 4 positions instead of 8) and add
> >> > the table markup.
> >> > - be sure that the section markups have the same number of
> >> > characters as the section title.
> >> >
> >> > Signed-off-by: Mauro Carvalho Chehab <[email protected]>
> >> > ---
> >> > Documentation/hwmon/index.rst | 3 +++
> >> > Documentation/hwmon/{ir38064 => ir38064.rst} | 21 ++++++++++++-------
> >> > .../hwmon/{isl68137 => isl68137.rst} | 16 ++++++++++----
> >> > .../hwmon/{lochnagar => lochnagar.rst} | 7 +++++--
> >> > 4 files changed, 33 insertions(+), 14 deletions(-)
> >> > rename Documentation/hwmon/{ir38064 => ir38064.rst} (76%)
> >> > rename Documentation/hwmon/{isl68137 => isl68137.rst} (85%)
> >> > rename Documentation/hwmon/{lochnagar => lochnagar.rst} (93%)
> >> >
> >> > diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst
> >> > index 893804414510..3fa14fe7b49c 100644
> >> > --- a/Documentation/hwmon/index.rst
> >> > +++ b/Documentation/hwmon/index.rst
> >> > @@ -65,6 +65,8 @@ Hardware Monitoring Kernel Drivers
> >> > ina2xx.rst
> >> > ina3221.rst
> >> > ir35221.rst
> >> > + ir38064.rst
> >> > + isl68137.rst
> >>
> >> Didn't notice it on the first patch adding index.rst, but I don't think
> >> it's customary to add .rst suffix to the toctree.
> >
> > Provided that all documents are at the same time, I guess it
> > doesn't matter having a .rst there or not.
>
> Parse error. No other index.rst has the suffixes.
Actually, there are a few that has, including the doc-guide
$ git grep \\.rst $(find Documentation/ -name index.rst)|cut -d: -f1|sort|uniq
Documentation/admin-guide/mm/index.rst
Documentation/doc-guide/index.rst
Documentation/filesystems/ext4/index.rst
Documentation/filesystems/index.rst
Documentation/hwmon/index.rst
Documentation/translations/it_IT/doc-guide/index.rst
Documentation/translations/it_IT/kernel-hacking/index.rst
Documentation/translations/it_IT/process/index.rst
Documentation/translations/zh_CN/process/index.rst
(I'm looking at linux-next).
Clearly, the Documentation/doc-guide/index.rst has it:
=================================
How to write kernel documentation
=================================
.. toctree::
:maxdepth: 1
sphinx.rst
kernel-doc.rst
parse-headers.rst
Anyway I'll send a patch removing the extra .rst from hwmon, to
be applied after this one, and another one for the doc-guide.
>
> > Btw, newer versions of Sphinx build can work with other formats
> > like markdown. I suspect that, if we end mixing markdown documents,
> > it would be worth having the extension there.
> >
> > FYI, someone recently added a markdown file at the tree:
> >
> > commit e453fa60e086786fe89ba15ee8fef80bc2e6ecc3
> > Author: Sascha Hauer <[email protected]>
> > Date: Fri Sep 7 14:36:46 2018 +0200
> >
> > Documentation: ubifs: Add authentication whitepaper
> >
> > Documentation/filesystems/ubifs-authentication.md
> >
> > IMO, the best would be to just run pandoc into it and convert
> > to .rst, than to mix different markup languages.
>
> Agreed. I'd rather we keep it all rst.
>
> BR,
> Jani.
>
>
Thanks,
Mauro