The polling mode workaround for the FU540-C000 on HiFive Unleashed A00
board was added earlier. The logic for this seems to work only in case
the interrupt property was missing/not added into the i2c0 device node.
Here we address this issue by identifying the SOC based on compatibility
string and set the master xfer's to polling mode if it's the FU540-C000
SoC.
The fix has been tested on Linux 5.9.0-rc8 with a PMOD based RTCC sensor
connected to I2C pins J1 header of the board. Log for reference
# uname -a
Linux buildroot 5.9.0-rc8-00001-g9da7791 #1 SMP Fri Oct 9 07:56:13 PDT 2020 riscv64 GNU/Linux
# i2cdetect -y 0
0 1 2 3 4 5 6 7 8 9 a b c d e f
00: -- -- -- -- -- -- -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
50: -- -- -- -- -- -- -- 57 -- -- -- -- -- -- -- --
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 6f
70: -- -- -- -- -- -- -- --
# i2cget 0 0x57 0 b -y
0xa5
# i2cset 0 0x57 0 0x9f b -y
# i2cget 0 0x57 0 b -y
0x9f
# i2cget 0 0x57 1 b -y
0xff
# i2cset 0 0x57 1 0xa9 b -y
# i2cget 0 0x57 1 b -y
0xa9
# i2cget 0 0x6f 0x20 b -y
0x98
# i2cset 0 0x6f 0x20 0xa5 b -y
# i2cget 0 0x6f 0x20 b -y
0xa5
# i2cget 0 0x6f 0x5f b -y
0x55
# i2cset 0 0x6f 0x5f 0x5a b -y
# i2cget 0 0x6f 0x5f b -y
0x5a
#
Without the fix here, it's observed that "i2cdetect -y 0"
turns the system unresponsive, with CPU stall messages.
Patch History:
===============================
V2:
-Incorporated changes as suggested by Peter Kosgaard
https://lkml.org/lkml/2020/10/8/663
V1: Base version
Sagar Shrikant Kadam (1):
i2c: ocores: fix polling mode workaround on FU540-C000 SoC
drivers/i2c/busses/i2c-ocores.c | 22 +++++++++++++---------
1 file changed, 13 insertions(+), 9 deletions(-)
--
2.7.4
The FU540-C000 has a broken IRQ and support was added earlier
so that it will operate in polling mode, but seems to work only
in case interrupts property is missing from the i2c0 dt-node.
This should not be the case and the driver should handle polling
mode with the interrupt property present in i2c0 node of the
device tree.
So check if it's the FU540-C000 soc and enable polling mode master
xfers, as the IRQ for this chip is broken.
Fixes commit c45d4ba86731 ("i2c: ocores: add polling mode workaround
for Sifive FU540-C000 SoC")
Signed-off-by: Sagar Shrikant Kadam <[email protected]>
---
drivers/i2c/busses/i2c-ocores.c | 22 +++++++++++++---------
1 file changed, 13 insertions(+), 9 deletions(-)
diff --git a/drivers/i2c/busses/i2c-ocores.c b/drivers/i2c/busses/i2c-ocores.c
index f5fc75b..9b3d1ab 100644
--- a/drivers/i2c/busses/i2c-ocores.c
+++ b/drivers/i2c/busses/i2c-ocores.c
@@ -686,17 +686,21 @@ static int ocores_i2c_probe(struct platform_device *pdev)
init_waitqueue_head(&i2c->wait);
+ /*
+ * Set OCORES_FLAG_BROKEN_IRQ to enable workaround for
+ * FU540-C000 SoC in polling mode.
+ * Since the SoC does have interrupt it's dt has the interrupt
+ * defined but it should be bypassed in driver as this SoC has
+ * a broken IRQ, hence update the master_xfer to use polling
+ * transfers.
+ */
+ if (of_device_is_compatible(pdev->dev.of_node,
+ "sifive,fu540-c000-i2c"))
+ i2c->flags |= OCORES_FLAG_BROKEN_IRQ;
+
irq = platform_get_irq(pdev, 0);
- if (irq == -ENXIO) {
+ if (i2c->flags & OCORES_FLAG_BROKEN_IRQ || irq == -ENXIO) {
ocores_algorithm.master_xfer = ocores_xfer_polling;
-
- /*
- * Set in OCORES_FLAG_BROKEN_IRQ to enable workaround for
- * FU540-C000 SoC in polling mode.
- */
- match = of_match_node(ocores_i2c_match, pdev->dev.of_node);
- if (match && (long)match->data == TYPE_SIFIVE_REV0)
- i2c->flags |= OCORES_FLAG_BROKEN_IRQ;
} else {
if (irq < 0)
return irq;
--
2.7.4
On Okt 09 2020, Sagar Shrikant Kadam wrote:
> diff --git a/drivers/i2c/busses/i2c-ocores.c b/drivers/i2c/busses/i2c-ocores.c
> index f5fc75b..9b3d1ab 100644
> --- a/drivers/i2c/busses/i2c-ocores.c
> +++ b/drivers/i2c/busses/i2c-ocores.c
> @@ -686,17 +686,21 @@ static int ocores_i2c_probe(struct platform_device *pdev)
>
> init_waitqueue_head(&i2c->wait);
>
> + /*
> + * Set OCORES_FLAG_BROKEN_IRQ to enable workaround for
> + * FU540-C000 SoC in polling mode.
> + * Since the SoC does have interrupt it's dt has the interrupt
Typo: its
Andreas.
--
Andreas Schwab, [email protected]
GPG Key fingerprint = 7578 EB47 D4E5 4D69 2510 2552 DF73 E780 A9DA AEC1
"And now for something completely different."
> -----Original Message-----
> From: Andreas Schwab <[email protected]>
> Sent: Friday, October 9, 2020 11:55 PM
> To: Sagar Kadam <[email protected]>
> Cc: [email protected]; [email protected]; linux-
> [email protected]; [email protected]; [email protected]; Paul
> Walmsley ( Sifive) <[email protected]>; [email protected];
> [email protected]
> Subject: Re: [PATCH v2 1/1] i2c: ocores: fix polling mode workaround on
> FU540-C000 SoC
>
> [External Email] Do not click links or attachments unless you recognize the
> sender and know the content is safe
>
> On Okt 09 2020, Sagar Shrikant Kadam wrote:
>
> > diff --git a/drivers/i2c/busses/i2c-ocores.c
> > b/drivers/i2c/busses/i2c-ocores.c index f5fc75b..9b3d1ab 100644
> > --- a/drivers/i2c/busses/i2c-ocores.c
> > +++ b/drivers/i2c/busses/i2c-ocores.c
> > @@ -686,17 +686,21 @@ static int ocores_i2c_probe(struct
> > platform_device *pdev)
> >
> > init_waitqueue_head(&i2c->wait);
> >
> > + /*
> > + * Set OCORES_FLAG_BROKEN_IRQ to enable workaround for
> > + * FU540-C000 SoC in polling mode.
> > + * Since the SoC does have interrupt it's dt has the interrupt
>
> Typo: its
>
Thanks Andreas,
I will submit v3 with the change.
BR,
Sagar
> Andreas.
>
> --
> Andreas Schwab, [email protected]
> GPG Key fingerprint = 7578 EB47 D4E5 4D69 2510 2552 DF73 E780 A9DA
> AEC1 "And now for something completely different."