Hi.
I just tried 2.6.0-test4 on my Laptop (JVC MP-XP7210, 256MB RAM, IDE).
However, it hangs on boot. I tried booting with acpi=off and also
with "acpi=off noapic". Both options seem to help nothing,
and the same output appears on all attempts to boot.
I compiled the kernel with gcc 3.3.2.
Here is the output I get:
[<c0 10 92 69>] Kernel_thread_helper+0x5/0xc
Code: 0f ba 6e 24 00 c7 44 24 04 00 00 00 00 89 34 24 e8 25 fa ff
<0> Kernel Panic: Fatal Exception in Interrupt
in interrupt handler - not syncing
(and here it hangs)
P.S.: I am not subscribed, please CC.
Here is also the output of lspci -vv run under 2.4.20-pre7-acpi:
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 630 Host (rev 31)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 32
Region 0: Memory at d4000000 (32-bit, non-prefetchable) [size=64M]
Capabilities: [c0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
00:00.1 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev d0) (prog-if 80 [Master])
Subsystem: Silicon Integrated Systems [SiS] SiS5513 EIDE Controller (A,B step)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 16
Region 4: I/O ports at d800 [size=16]
00:01.0 ISA bridge: Silicon Integrated Systems [SiS] 85C503/5513
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:01.1 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 10/100 Ethernet (rev 82)
Subsystem: Asustek Computer, Inc.: Unknown device 1455
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (13000ns min, 2750ns max)
Interrupt: pin C routed to IRQ 5
Region 0: I/O ports at d400 [size=256]
Region 1: Memory at d3800000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=160mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.2 USB Controller: Silicon Integrated Systems [SiS] SiS7001 USB Controller (rev 07) (prog-if 10 [OHCI])
Subsystem: Silicon Integrated Systems [SiS] SiS7001 USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (20000ns max), cache line size 08
Interrupt: pin D routed to IRQ 4
Region 0: Memory at d3000000 (32-bit, non-prefetchable) [size=4K]
00:01.3 USB Controller: Silicon Integrated Systems [SiS] SiS7001 USB Controller (rev 07) (prog-if 10 [OHCI])
Subsystem: Silicon Integrated Systems [SiS] Onboard USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (20000ns max), cache line size 08
Interrupt: pin D routed to IRQ 4
Region 0: Memory at d2800000 (32-bit, non-prefetchable) [size=4K]
00:01.4 Multimedia audio controller: Silicon Integrated Systems [SiS] SiS PCI Audio Accelerator (rev 02)
Subsystem: Asustek Computer, Inc.: Unknown device 1473
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 6000ns max)
Interrupt: pin B routed to IRQ 7
Region 0: I/O ports at d000 [size=256]
Region 1: Memory at d2000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=55mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.6 Modem: Silicon Integrated Systems [SiS] Intel 537 [56k Winmodem] (rev a0) (prog-if 00 [Generic])
Subsystem: Asustek Computer, Inc.: Unknown device 1616
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (13000ns min, 2750ns max)
Interrupt: pin C routed to IRQ 5
Region 0: I/O ports at b800 [size=256]
Region 1: I/O ports at b400 [size=128]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.0 PCI bridge: Silicon Integrated Systems [SiS] SiS 530 Virtual PCI-to-PCI bridge (AGP) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: d1800000-d1ffffff
Prefetchable memory behind bridge: d8000000-e7efffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
00:09.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 88)
Subsystem: Asustek Computer, Inc.: Unknown device 1674
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 000de000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 10400000-107ff000 (prefetchable)
Memory window 1: 10800000-10bff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:09.1 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 88)
Subsystem: Asustek Computer, Inc.: Unknown device 1674
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
Memory window 0: 10c00000-10fff000 (prefetchable)
Memory window 1: 11000000-113ff000
I/O window 0: 00004800-000048ff
I/O window 1: 00004c00-00004cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:09.2 System peripheral: Ricoh Co Ltd: Unknown device 0576
Subsystem: Asustek Computer, Inc.: Unknown device 1674
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 10001000 (32-bit, non-prefetchable) [disabled] [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME+
00:0a.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21 IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 1677
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 1000ns max), cache line size 08
Interrupt: pin A routed to IRQ 4
Region 0: Memory at d1000000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at d0800000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS] SiS630 GUI Accelerator+3D (rev 31) (prog-if 00 [VGA])
Subsystem: Asustek Computer, Inc.: Unknown device 1672
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
BIST result: 00
Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at d1800000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at a800 [size=128]
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] AGP version 2.0
Status: RQ=16 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
--
CYa,
Mario
Mario Lang <[email protected]> wrote:
>
> I just tried 2.6.0-test4 on my Laptop (JVC MP-XP7210, 256MB RAM, IDE).
> However, it hangs on boot. I tried booting with acpi=off and also
> with "acpi=off noapic". Both options seem to help nothing,
> and the same output appears on all attempts to boot.
>
> I compiled the kernel with gcc 3.3.2.
>
> Here is the output I get:
>
> [<c0 10 92 69>] Kernel_thread_helper+0x5/0xc
> Code: 0f ba 6e 24 00 c7 44 24 04 00 00 00 00 89 34 24 e8 25 fa ff
> <0> Kernel Panic: Fatal Exception in Interrupt
> in interrupt handler - not syncing
There must have been more output than that? Please transcribe some more of
the backtrace and send it. Don't worry about all the hex numbers: the
important parts are these:
EIP is at i810fb_cursor+0x1da/0x240 [i810fb]
Call Trace:
[<...>] apic_timer_interrupt+0x1a/0x20
[<...>] bh_lru_install+0xb5/0x100
[<...>] __find_get_block+0x73/0xf0
[<...>] __getblk+0x2b/0x60
[<...>] is_tree_node+0x6b/0x70
[<...>] search_by_key+0x6f9/0xf30
[<...>] search_for_position_by_key+0x1be/0x3d0
[<...>] apic_timer_interrupt+0x1a/0x20
Also, try stripping your kernel down by unconfiguring drivers and features
which are not needed for a successful boot. This will help identify the
buggy component.
Also, try adding the string `initcall_debug' to the kernel boot command
line. Watch out for the messages "calling initcall 0xNNNNNNNN". Take a
note of the final address which is printed before the crash and look it up
in the 2.6 kernel's System.map file.
Thanks.
Hi,
I've got the same laptop, I will give test4 a try to see
what happens.
Greetings,
Jurgen
OK, I've tried 2.6.0-test4 on my XP7210 and it works just
happily. Everything is working: ACPI, PCMCIA, ALSA, SISFB the works...
Maybe it's your version of GCC? I use GCC 3.2.2 which comes with RH9.
Cheers,
Jurgen
On Fri, 2003-08-29 at 15:21, Mario Lang wrote:
> Hi.
>
> I just tried 2.6.0-test4 on my Laptop (JVC MP-XP7210, 256MB RAM, IDE).
> However, it hangs on boot. I tried booting with acpi=off and also
> with "acpi=off noapic". Both options seem to help nothing,
> and the same output appears on all attempts to boot.
>
> I compiled the kernel with gcc 3.3.2.
>
> Here is the output I get:
>
> [<c0 10 92 69>] Kernel_thread_helper+0x5/0xc
> Code: 0f ba 6e 24 00 c7 44 24 04 00 00 00 00 89 34 24 e8 25 fa ff
> <0> Kernel Panic: Fatal Exception in Interrupt
> in interrupt handler - not syncing
>
> (and here it hangs)
>
> P.S.: I am not subscribed, please CC.
>
> Here is also the output of lspci -vv run under 2.4.20-pre7-acpi:
>
> 00:00.0 Host bridge: Silicon Integrated Systems [SiS] 630 Host (rev 31)
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
> Latency: 32
> Region 0: Memory at d4000000 (32-bit, non-prefetchable) [size=64M]
> Capabilities: [c0] AGP version 2.0
> Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2
> Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
>
> 00:00.1 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev d0) (prog-if 80 [Master])
> Subsystem: Silicon Integrated Systems [SiS] SiS5513 EIDE Controller (A,B step)
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 16
> Region 4: I/O ports at d800 [size=16]
>
> 00:01.0 ISA bridge: Silicon Integrated Systems [SiS] 85C503/5513
> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
>
> 00:01.1 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 10/100 Ethernet (rev 82)
> Subsystem: Asustek Computer, Inc.: Unknown device 1455
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (13000ns min, 2750ns max)
> Interrupt: pin C routed to IRQ 5
> Region 0: I/O ports at d400 [size=256]
> Region 1: Memory at d3800000 (32-bit, non-prefetchable) [size=4K]
> Expansion ROM at <unassigned> [disabled] [size=128K]
> Capabilities: [40] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=160mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:01.2 USB Controller: Silicon Integrated Systems [SiS] SiS7001 USB Controller (rev 07) (prog-if 10 [OHCI])
> Subsystem: Silicon Integrated Systems [SiS] SiS7001 USB Controller
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (20000ns max), cache line size 08
> Interrupt: pin D routed to IRQ 4
> Region 0: Memory at d3000000 (32-bit, non-prefetchable) [size=4K]
>
> 00:01.3 USB Controller: Silicon Integrated Systems [SiS] SiS7001 USB Controller (rev 07) (prog-if 10 [OHCI])
> Subsystem: Silicon Integrated Systems [SiS] Onboard USB Controller
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (20000ns max), cache line size 08
> Interrupt: pin D routed to IRQ 4
> Region 0: Memory at d2800000 (32-bit, non-prefetchable) [size=4K]
>
> 00:01.4 Multimedia audio controller: Silicon Integrated Systems [SiS] SiS PCI Audio Accelerator (rev 02)
> Subsystem: Asustek Computer, Inc.: Unknown device 1473
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (500ns min, 6000ns max)
> Interrupt: pin B routed to IRQ 7
> Region 0: I/O ports at d000 [size=256]
> Region 1: Memory at d2000000 (32-bit, non-prefetchable) [size=4K]
> Capabilities: [dc] Power Management version 2
> Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=55mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:01.6 Modem: Silicon Integrated Systems [SiS] Intel 537 [56k Winmodem] (rev a0) (prog-if 00 [Generic])
> Subsystem: Asustek Computer, Inc.: Unknown device 1616
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (13000ns min, 2750ns max)
> Interrupt: pin C routed to IRQ 5
> Region 0: I/O ports at b800 [size=256]
> Region 1: I/O ports at b400 [size=128]
> Capabilities: [48] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:02.0 PCI bridge: Silicon Integrated Systems [SiS] SiS 530 Virtual PCI-to-PCI bridge (AGP) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
> I/O behind bridge: 0000a000-0000afff
> Memory behind bridge: d1800000-d1ffffff
> Prefetchable memory behind bridge: d8000000-e7efffff
> BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
>
> 00:09.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 88)
> Subsystem: Asustek Computer, Inc.: Unknown device 1674
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 168
> Interrupt: pin A routed to IRQ 11
> Region 0: Memory at 000de000 (32-bit, non-prefetchable) [size=4K]
> Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
> Memory window 0: 10400000-107ff000 (prefetchable)
> Memory window 1: 10800000-10bff000
> I/O window 0: 00004000-000040ff
> I/O window 1: 00004400-000044ff
> BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
> 16-bit legacy interface ports at 0001
>
> 00:09.1 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 88)
> Subsystem: Asustek Computer, Inc.: Unknown device 1674
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 168
> Interrupt: pin A routed to IRQ 11
> Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
> Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
> Memory window 0: 10c00000-10fff000 (prefetchable)
> Memory window 1: 11000000-113ff000
> I/O window 0: 00004800-000048ff
> I/O window 1: 00004c00-00004cff
> BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
> 16-bit legacy interface ports at 0001
>
> 00:09.2 System peripheral: Ricoh Co Ltd: Unknown device 0576
> Subsystem: Asustek Computer, Inc.: Unknown device 1674
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Interrupt: pin A routed to IRQ 11
> Region 0: Memory at 10001000 (32-bit, non-prefetchable) [disabled] [size=256]
> Capabilities: [80] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=2 PME+
>
> 00:0a.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21 IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI])
> Subsystem: Asustek Computer, Inc.: Unknown device 1677
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (500ns min, 1000ns max), cache line size 08
> Interrupt: pin A routed to IRQ 4
> Region 0: Memory at d1000000 (32-bit, non-prefetchable) [size=2K]
> Region 1: Memory at d0800000 (32-bit, non-prefetchable) [size=16K]
> Capabilities: [44] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME+
>
> 01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS] SiS630 GUI Accelerator+3D (rev 31) (prog-if 00 [VGA])
> Subsystem: Asustek Computer, Inc.: Unknown device 1672
> Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> BIST result: 00
> Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M]
> Region 1: Memory at d1800000 (32-bit, non-prefetchable) [size=128K]
> Region 2: I/O ports at a800 [size=128]
> Capabilities: [40] Power Management version 1
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [50] AGP version 2.0
> Status: RQ=16 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
> Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
>
Andrew Morton <[email protected]> writes:
> Mario Lang <[email protected]> wrote:
>>
>> I just tried 2.6.0-test4 on my Laptop (JVC MP-XP7210, 256MB RAM, IDE).
>> However, it hangs on boot. I tried booting with acpi=off and also
>> with "acpi=off noapic". Both options seem to help nothing,
>> and the same output appears on all attempts to boot.
>>
>> I compiled the kernel with gcc 3.3.2.
>>
>> Here is the output I get:
>>
>> [<c0 10 92 69>] Kernel_thread_helper+0x5/0xc
>> Code: 0f ba 6e 24 00 c7 44 24 04 00 00 00 00 89 34 24 e8 25 fa ff
>> <0> Kernel Panic: Fatal Exception in Interrupt
>> in interrupt handler - not syncing
>
> There must have been more output than that? Please transcribe some more of
> the backtrace and send it. Don't worry about all the hex numbers: the
> important parts are these:
>
> EIP is at i810fb_cursor+0x1da/0x240 [i810fb]
>
> Call Trace:
> [<...>] apic_timer_interrupt+0x1a/0x20
> [<...>] bh_lru_install+0xb5/0x100
> [<...>] __find_get_block+0x73/0xf0
> [<...>] __getblk+0x2b/0x60
> [<...>] is_tree_node+0x6b/0x70
> [<...>] search_by_key+0x6f9/0xf30
> [<...>] search_for_position_by_key+0x1be/0x3d0
> [<...>] apic_timer_interrupt+0x1a/0x20
Sorry, I did ask a college to type this info for me since I am
blind and can't read screen output at that early stage in the
boot process. It seems he was very lazy.
> Also, try stripping your kernel down by unconfiguring drivers and features
> which are not needed for a successful boot.
Thanks you for reminding me! I should have found this myself.
The problem was that I accidentally enabled ACPI CPU enumeration support
for HT. Well, this is a pIII Mobile, and surely has
no Hyperthreading.
Now the machine boots fine. Only "error" I saw in
dmesg is that my chipset is not yet supported for SpeedStep.
--
CYa,
Mario | Debian Developer <URL:http://debian.org/>
| Get my public key via finger [email protected]
| 1024D/7FC1A0854909BCCDBE6C102DDFFC022A6B113E44