Add support for Fibocom L7xx module series and variants.
L716-EU-60 (ECM):
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 17 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=19d2 ProdID=0579 Rev= 1.00
S: Manufacturer=Fibocom,Incorporated
S: Product=Fibocom Mobile Boardband
S: SerialNumber=1234567890ABCDEF
C:* #Ifs= 7 Cfg#= 1 Atr=e0 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=06 Prot=00
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
E: Ad=87(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
L716-EU-60 (RNDIS):
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 21 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2cb7 ProdID=0001 Rev= 1.00
S: Manufacturer=Fibocom,Incorporated
S: Product=Fibocom Mobile Boardband
S: SerialNumber=1234567890ABCDEF
C:* #Ifs= 7 Cfg#= 1 Atr=e0 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=06 Prot=00
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
E: Ad=87(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
L716-EU-10 (ECM):
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 21 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2cb7 ProdID=0001 Rev= 1.00
S: Manufacturer=Fibocom,Incorporated
S: Product=Fibocom Mobile Boardband
S: SerialNumber=1234567890ABCDEF
C:* #Ifs= 7 Cfg#= 1 Atr=e0 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=06 Prot=00
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
E: Ad=87(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Victor Fragoso <[email protected]>
---
drivers/usb/serial/option.c | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
index 45dcfaadaf98..4ba3dc352d65 100644
--- a/drivers/usb/serial/option.c
+++ b/drivers/usb/serial/option.c
@@ -2262,6 +2262,11 @@ static const struct usb_device_id option_ids[] =
{
{ USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x01a2, 0xff)
}, /* Fibocom FM101-GL (laptop MBIM) */
{ USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x01a4,
0xff), /* Fibocom FM101-GL (laptop MBIM) */
.driver_info = RSVD(4) },
+ { USB_DEVICE_AND_INTERFACE_INFO(0x2cb7, 0x0001, 0xff, 0xff,
0xff) }, /* Fibocom L71x */
+ { USB_DEVICE_AND_INTERFACE_INFO(0x2cb7, 0x0001, 0x0a, 0x00,
0xff) }, /* Fibocom L71x */
+ { USB_DEVICE_AND_INTERFACE_INFO(0x2cb7, 0x0100, 0xff, 0xff,
0xff) }, /* Fibocom L71x */
+ { USB_DEVICE_AND_INTERFACE_INFO(0x19d2, 0x0256, 0xff, 0xff,
0xff) }, /* Fibocom L71x */
+ { USB_DEVICE_AND_INTERFACE_INFO(0x19d2, 0x0579, 0xff, 0xff,
0xff) }, /* Fibocom L71x */
{ USB_DEVICE_INTERFACE_CLASS(0x2df3, 0x9d03, 0xff)
}, /* LongSung M5710 */
{ USB_DEVICE_INTERFACE_CLASS(0x305a, 0x1404, 0xff)
}, /* GosunCn GM500 RNDIS */
{ USB_DEVICE_INTERFACE_CLASS(0x305a, 0x1405, 0xff)
}, /* GosunCn GM500 MBIM */
--
2.34.1
On 10/26/2023 8:24, Victor Fragoso wrote:
> Add support for Fibocom L7xx module series and variants.
>
> L716-EU-60 (ECM):
> T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 17 Spd=480 MxCh= 0
> D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
> P: Vendor=19d2 ProdID=0579 Rev= 1.00
> S: Manufacturer=Fibocom,Incorporated
> S: Product=Fibocom Mobile Boardband
> S: SerialNumber=1234567890ABCDEF
> C:* #Ifs= 7 Cfg#= 1 Atr=e0 MxPwr=500mA
> A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=06 Prot=00
> I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
> E: Ad=87(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
> I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
> I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
> E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
> E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>
> L716-EU-60 (RNDIS):
> T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 21 Spd=480 MxCh= 0
> D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
> P: Vendor=2cb7 ProdID=0001 Rev= 1.00
> S: Manufacturer=Fibocom,Incorporated
> S: Product=Fibocom Mobile Boardband
> S: SerialNumber=1234567890ABCDEF
> C:* #Ifs= 7 Cfg#= 1 Atr=e0 MxPwr=500mA
> A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=06 Prot=00
> I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
> E: Ad=87(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
> I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
> I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
> E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
> E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>
> L716-EU-10 (ECM):
> T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 21 Spd=480 MxCh= 0
> D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
> P: Vendor=2cb7 ProdID=0001 Rev= 1.00
> S: Manufacturer=Fibocom,Incorporated
> S: Product=Fibocom Mobile Boardband
> S: SerialNumber=1234567890ABCDEF
> C:* #Ifs= 7 Cfg#= 1 Atr=e0 MxPwr=500mA
> A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=06 Prot=00
> I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
> E: Ad=87(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
> I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
> I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
> E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
> E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>
> Signed-off-by: Victor Fragoso <[email protected]>
> ---
> drivers/usb/serial/option.c | 5 +++++
> 1 file changed, 5 insertions(+)
>
> diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
> index 45dcfaadaf98..4ba3dc352d65 100644
> --- a/drivers/usb/serial/option.c
> +++ b/drivers/usb/serial/option.c
> @@ -2262,6 +2262,11 @@ static const struct usb_device_id option_ids[] =
> {
> { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x01a2, 0xff)
> }, /* Fibocom FM101-GL (laptop MBIM) */
> { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x01a4,
> 0xff), /* Fibocom FM101-GL (laptop MBIM) */
> .driver_info = RSVD(4) },
> + { USB_DEVICE_AND_INTERFACE_INFO(0x2cb7, 0x0001, 0xff, 0xff,
> 0xff) }, /* Fibocom L71x */
> + { USB_DEVICE_AND_INTERFACE_INFO(0x2cb7, 0x0001, 0x0a, 0x00,
> 0xff) }, /* Fibocom L71x */
> + { USB_DEVICE_AND_INTERFACE_INFO(0x2cb7, 0x0100, 0xff, 0xff,
> 0xff) }, /* Fibocom L71x */
> + { USB_DEVICE_AND_INTERFACE_INFO(0x19d2, 0x0256, 0xff, 0xff,
> 0xff) }, /* Fibocom L71x */
> + { USB_DEVICE_AND_INTERFACE_INFO(0x19d2, 0x0579, 0xff, 0xff,
> 0xff) }, /* Fibocom L71x */
> { USB_DEVICE_INTERFACE_CLASS(0x2df3, 0x9d03, 0xff)
> }, /* LongSung M5710 */
> { USB_DEVICE_INTERFACE_CLASS(0x305a, 0x1404, 0xff)
> }, /* GosunCn GM500 RNDIS */
> { USB_DEVICE_INTERFACE_CLASS(0x305a, 0x1405, 0xff)
> }, /* GosunCn GM500 MBIM */
Hi Victor, thanks for the patch, there is unfortunately the following
errors in it:
The device list is sorted in ascending order based on vid:pid, you have
inserted all of your added Id's in the wrong place.
19d2:0579 is a ZTE device Id and should be placed among the other 19d2
devices.
You have not included usb-devices output for 19d2:0256 and 2cb7:0100,
and I have strong reasons to believe that they should not be included in
the option driver.
If you are of another opinion then please show the usb-devices output
for them, otherwise remove them from the patch.
You have added support for an interface with the attributes 0a/00/ff ,
there is no such interface in your provided usb-devices listing,
interface Class 0a does not even belong to the option driver.
Thanks
Lars
On Thu, 2023-10-26 at 01:24 +0000, Victor Fragoso wrote:
> Add support for Fibocom L7xx module series and variants.
>
> L716-EU-60 (ECM):
> T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 17 Spd=480 MxCh= 0
> D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
> P: Vendor=19d2 ProdID=0579 Rev= 1.00
> S: Manufacturer=Fibocom,Incorporated
> S: Product=Fibocom Mobile Boardband
> S: SerialNumber=1234567890ABCDEF
> C:* #Ifs= 7 Cfg#= 1 Atr=e0 MxPwr=500mA
> A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=06 Prot=00
> I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
> E: Ad=87(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
> I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
> I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
> E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
> E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>
> L716-EU-60 (RNDIS):
> T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 21 Spd=480 MxCh= 0
> D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
> P: Vendor=2cb7 ProdID=0001 Rev= 1.00
> S: Manufacturer=Fibocom,Incorporated
> S: Product=Fibocom Mobile Boardband
> S: SerialNumber=1234567890ABCDEF
> C:* #Ifs= 7 Cfg#= 1 Atr=e0 MxPwr=500mA
> A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=06 Prot=00
> I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
> E: Ad=87(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
> I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
> I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
> E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
> E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>
> L716-EU-10 (ECM):
> T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 21 Spd=480 MxCh= 0
> D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
> P: Vendor=2cb7 ProdID=0001 Rev= 1.00
> S: Manufacturer=Fibocom,Incorporated
> S: Product=Fibocom Mobile Boardband
> S: SerialNumber=1234567890ABCDEF
> C:* #Ifs= 7 Cfg#= 1 Atr=e0 MxPwr=500mA
> A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=06 Prot=00
> I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
> E: Ad=87(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
> I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
> I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
> E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
> E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>
> Signed-off-by: Victor Fragoso <[email protected]>
> ---
> drivers/usb/serial/option.c | 5 +++++
> 1 file changed, 5 insertions(+)
>
> diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
> index 45dcfaadaf98..4ba3dc352d65 100644
> --- a/drivers/usb/serial/option.c
> +++ b/drivers/usb/serial/option.c
> @@ -2262,6 +2262,11 @@ static const struct usb_device_id option_ids[] =
> {
> { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x01a2, 0xff)
> }, /* Fibocom FM101-GL (laptop MBIM) */
> { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x01a4,
> 0xff), /* Fibocom FM101-GL (laptop MBIM) */
It looks like your mail client wrapped long lines; you'll want to
resend with a "preformatted" option or something, or use "git send-
email" to make sure the formatting doesn't get screwed up.
Also, are you at all able to give hints in the comments about what kind
of ports these are? AT? GPS? PPP? etc? That's usually described in the
driver documentation or in the Windows drivers themselves.
Dan
> .driver_info = RSVD(4) },
> + { USB_DEVICE_AND_INTERFACE_INFO(0x2cb7, 0x0001, 0xff, 0xff,
> 0xff) }, /* Fibocom L71x */
> + { USB_DEVICE_AND_INTERFACE_INFO(0x2cb7, 0x0001, 0x0a, 0x00,
> 0xff) }, /* Fibocom L71x */
> + { USB_DEVICE_AND_INTERFACE_INFO(0x2cb7, 0x0100, 0xff, 0xff,
> 0xff) }, /* Fibocom L71x */
> + { USB_DEVICE_AND_INTERFACE_INFO(0x19d2, 0x0256, 0xff, 0xff,
> 0xff) }, /* Fibocom L71x */
> + { USB_DEVICE_AND_INTERFACE_INFO(0x19d2, 0x0579, 0xff, 0xff,
> 0xff) }, /* Fibocom L71x */
> { USB_DEVICE_INTERFACE_CLASS(0x2df3, 0x9d03, 0xff)
> }, /* LongSung M5710 */
> { USB_DEVICE_INTERFACE_CLASS(0x305a, 0x1404, 0xff)
> }, /* GosunCn GM500 RNDIS */
> { USB_DEVICE_INTERFACE_CLASS(0x305a, 0x1405, 0xff)
> }, /* GosunCn GM500 MBIM */
> --
> 2.34.1
>
>
On Thu, 2023-10-26 at 08:49 -0500, Dan Williams wrote:
> On Thu, 2023-10-26 at 01:24 +0000, Victor Fragoso wrote:
> > Add support for Fibocom L7xx module series and variants.
> >
> > L716-EU-60 (ECM):
> > T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 17 Spd=480 MxCh= 0
> > D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
> > P: Vendor=19d2 ProdID=0579 Rev= 1.00
> > S: Manufacturer=Fibocom,Incorporated
> > S: Product=Fibocom Mobile Boardband
> > S: SerialNumber=1234567890ABCDEF
> > C:* #Ifs= 7 Cfg#= 1 Atr=e0 MxPwr=500mA
> > A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=06 Prot=00
> > I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
> > E: Ad=87(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
> > I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
> > I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
> > E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> > E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> > E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> > E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> > E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
> > E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> >
> > L716-EU-60 (RNDIS):
> > T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 21 Spd=480 MxCh= 0
> > D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
> > P: Vendor=2cb7 ProdID=0001 Rev= 1.00
> > S: Manufacturer=Fibocom,Incorporated
> > S: Product=Fibocom Mobile Boardband
> > S: SerialNumber=1234567890ABCDEF
> > C:* #Ifs= 7 Cfg#= 1 Atr=e0 MxPwr=500mA
> > A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=06 Prot=00
> > I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
> > E: Ad=87(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
> > I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
> > I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
> > E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> > E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> > E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> > E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> > E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
> > E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> >
> > L716-EU-10 (ECM):
> > T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 21 Spd=480 MxCh= 0
> > D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
> > P: Vendor=2cb7 ProdID=0001 Rev= 1.00
> > S: Manufacturer=Fibocom,Incorporated
> > S: Product=Fibocom Mobile Boardband
> > S: SerialNumber=1234567890ABCDEF
> > C:* #Ifs= 7 Cfg#= 1 Atr=e0 MxPwr=500mA
> > A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=06 Prot=00
> > I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
> > E: Ad=87(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
> > I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
> > I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
> > E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> > E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> > E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> > E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> > E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
> > E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> >
> > Signed-off-by: Victor Fragoso <[email protected]>
> > ---
> > drivers/usb/serial/option.c | 5 +++++
> > 1 file changed, 5 insertions(+)
> >
> > diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
> > index 45dcfaadaf98..4ba3dc352d65 100644
> > --- a/drivers/usb/serial/option.c
> > +++ b/drivers/usb/serial/option.c
> > @@ -2262,6 +2262,11 @@ static const struct usb_device_id option_ids[] =
> > {
> > { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x01a2, 0xff)
> > }, /* Fibocom FM101-GL (laptop MBIM) */
> > { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x01a4,
> > 0xff), /* Fibocom FM101-GL (laptop MBIM) */
>
> It looks like your mail client wrapped long lines; you'll want to
> resend with a "preformatted" option or something, or use "git send-
> email" to make sure the formatting doesn't get screwed up.
>
> Also, are you at all able to give hints in the comments about what kind
> of ports these are? AT? GPS? PPP? etc? That's usually described in the
> driver documentation or in the Windows drivers themselves.
>
> Dan
>
> > .driver_info = RSVD(4) },
> > + { USB_DEVICE_AND_INTERFACE_INFO(0x2cb7, 0x0001, 0xff, 0xff,
> > 0xff) }, /* Fibocom L71x */
> > + { USB_DEVICE_AND_INTERFACE_INFO(0x2cb7, 0x0001, 0x0a, 0x00,
> > 0xff) }, /* Fibocom L71x */
> > + { USB_DEVICE_AND_INTERFACE_INFO(0x2cb7, 0x0100, 0xff, 0xff,
> > 0xff) }, /* Fibocom L71x */
> > + { USB_DEVICE_AND_INTERFACE_INFO(0x19d2, 0x0256, 0xff, 0xff,
> > 0xff) }, /* Fibocom L71x */
> > + { USB_DEVICE_AND_INTERFACE_INFO(0x19d2, 0x0579, 0xff, 0xff,
> > 0xff) }, /* Fibocom L71x */
> > { USB_DEVICE_INTERFACE_CLASS(0x2df3, 0x9d03, 0xff)
> > }, /* LongSung M5710 */
> > { USB_DEVICE_INTERFACE_CLASS(0x305a, 0x1404, 0xff)
> > }, /* GosunCn GM500 RNDIS */
> > { USB_DEVICE_INTERFACE_CLASS(0x305a, 0x1405, 0xff)
> > }, /* GosunCn GM500 MBIM */
> > --
> > 2.34.1
> >
> >
>
Hi Dan, sorry about the wrapped lines. I hope will be right for next
one.
About the hints on comments (AT, PPP, etc) I am not so sure if I should
add other hints.
As I've mentioned on the other email to Lars:
I am a Field Application Enginner at Fibocom Brazil and I am using the
IDs from our internal and official documentation.
This IDs will guarantee that can be used on all the variants devices
from L71x series.
For example, the 0x2cb7 0x0001 can be used by L716-EU on RNDIS, L716-
EU-10 on ECM and L710 too. While 19d2 0579 can be used by L716-EU-60 on
ECM and probably other variants.
So, to avoid any misunderstand I prefer to keep it simple and mention
just as L71x series.
What do you think?
Victor Fragoso
On Thu, 2023-10-26 at 20:13 +0700, Lars Melin wrote:
> On 10/26/2023 8:24, Victor Fragoso wrote:
> > Add support for Fibocom L7xx module series and variants.
> >
> > L716-EU-60 (ECM):
> > T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 17 Spd=480 MxCh= 0
> > D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
> > P: Vendor=19d2 ProdID=0579 Rev= 1.00
> > S: Manufacturer=Fibocom,Incorporated
> > S: Product=Fibocom Mobile Boardband
> > S: SerialNumber=1234567890ABCDEF
> > C:* #Ifs= 7 Cfg#= 1 Atr=e0 MxPwr=500mA
> > A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=06 Prot=00
> > I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
> > E: Ad=87(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
> > I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
> > I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
> > E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> > E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> > E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> > E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> > E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
> > E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> >
> > L716-EU-60 (RNDIS):
> > T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 21 Spd=480 MxCh= 0
> > D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
> > P: Vendor=2cb7 ProdID=0001 Rev= 1.00
> > S: Manufacturer=Fibocom,Incorporated
> > S: Product=Fibocom Mobile Boardband
> > S: SerialNumber=1234567890ABCDEF
> > C:* #Ifs= 7 Cfg#= 1 Atr=e0 MxPwr=500mA
> > A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=06 Prot=00
> > I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
> > E: Ad=87(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
> > I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
> > I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
> > E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> > E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> > E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> > E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> > E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
> > E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> >
> > L716-EU-10 (ECM):
> > T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 21 Spd=480 MxCh= 0
> > D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
> > P: Vendor=2cb7 ProdID=0001 Rev= 1.00
> > S: Manufacturer=Fibocom,Incorporated
> > S: Product=Fibocom Mobile Boardband
> > S: SerialNumber=1234567890ABCDEF
> > C:* #Ifs= 7 Cfg#= 1 Atr=e0 MxPwr=500mA
> > A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=06 Prot=00
> > I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
> > E: Ad=87(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
> > I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
> > I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
> > E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> > E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> > E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> > E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> > E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
> > E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> >
> > Signed-off-by: Victor Fragoso <[email protected]>
> > ---
> > drivers/usb/serial/option.c | 5 +++++
> > 1 file changed, 5 insertions(+)
> >
> > diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
> > index 45dcfaadaf98..4ba3dc352d65 100644
> > --- a/drivers/usb/serial/option.c
> > +++ b/drivers/usb/serial/option.c
> > @@ -2262,6 +2262,11 @@ static const struct usb_device_id option_ids[] =
> > {
> > { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x01a2, 0xff)
> > }, /* Fibocom FM101-GL (laptop MBIM) */
> > { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x01a4,
> > 0xff), /* Fibocom FM101-GL (laptop MBIM) */
> > .driver_info = RSVD(4) },
> > + { USB_DEVICE_AND_INTERFACE_INFO(0x2cb7, 0x0001, 0xff, 0xff,
> > 0xff) }, /* Fibocom L71x */
> > + { USB_DEVICE_AND_INTERFACE_INFO(0x2cb7, 0x0001, 0x0a, 0x00,
> > 0xff) }, /* Fibocom L71x */
> > + { USB_DEVICE_AND_INTERFACE_INFO(0x2cb7, 0x0100, 0xff, 0xff,
> > 0xff) }, /* Fibocom L71x */
> > + { USB_DEVICE_AND_INTERFACE_INFO(0x19d2, 0x0256, 0xff, 0xff,
> > 0xff) }, /* Fibocom L71x */
> > + { USB_DEVICE_AND_INTERFACE_INFO(0x19d2, 0x0579, 0xff, 0xff,
> > 0xff) }, /* Fibocom L71x */
> > { USB_DEVICE_INTERFACE_CLASS(0x2df3, 0x9d03, 0xff)
> > }, /* LongSung M5710 */
> > { USB_DEVICE_INTERFACE_CLASS(0x305a, 0x1404, 0xff)
> > }, /* GosunCn GM500 RNDIS */
> > { USB_DEVICE_INTERFACE_CLASS(0x305a, 0x1405, 0xff)
> > }, /* GosunCn GM500 MBIM */
>
>
> Hi Victor, thanks for the patch, there is unfortunately the following
> errors in it:
> The device list is sorted in ascending order based on vid:pid, you have
> inserted all of your added Id's in the wrong place.
>
> 19d2:0579 is a ZTE device Id and should be placed among the other 19d2
> devices.
>
> You have not included usb-devices output for 19d2:0256 and 2cb7:0100,
> and I have strong reasons to believe that they should not be included in
> the option driver.
> If you are of another opinion then please show the usb-devices output
> for them, otherwise remove them from the patch.
>
> You have added support for an interface with the attributes 0a/00/ff ,
> there is no such interface in your provided usb-devices listing,
> interface Class 0a does not even belong to the option driver.
>
> Thanks
> Lars
Hi Lars, sorry about the wrong order, I will correct it.
But about the ZTE device ID, I belive that we should insert among
Fibocom drivers because we are talking about a Fibocom module that is
using an ZTE Chipset.
So, this is exactly the same situation from Fibocom L610 IDs (0x1782,
0x4d10 / 0x1782, 0x4d11) that is using the Unisoc Chipset but were
inserted among Fibocom drivers.
And about the usb-devices output, let me explain better:
I am a Field Application Enginner at Fibocom Brazil and I am using the
IDs from our internal and official documentation.
On this documents its suggested to add all this IDs because it will
guarantee that can be used on all the variants devices from L71x series
(that can change according to different part number, region support or
network protocol).
Unfortunately, I don't have all the modules variations available with
me right now to test and share all the outputs.
Can we continue with all the IDs that I have inserted?
Or do you prefer to keep just the devices that I tested by myself until
now?
Victor Fragoso
On 10/28/2023 0:55, Victor Fragoso wrote:
> On Thu, 2023-10-26 at 20:13 +0700, Lars Melin wrote:
>> On 10/26/2023 8:24, Victor Fragoso wrote:
>>> Add support for Fibocom L7xx module series and variants.
>>>
>>> L716-EU-60 (ECM):
>>> T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 17 Spd=480 MxCh= 0
>>> D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
>>> P: Vendor=19d2 ProdID=0579 Rev= 1.00
>>> S: Manufacturer=Fibocom,Incorporated
>>> S: Product=Fibocom Mobile Boardband
>>> S: SerialNumber=1234567890ABCDEF
>>> C:* #Ifs= 7 Cfg#= 1 Atr=e0 MxPwr=500mA
>>> A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=06 Prot=00
>>> I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
>>> E: Ad=87(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
>>> I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
>>> I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
>>> E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>>> E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>>> I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
>>> E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>>> E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>>> I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
>>> E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>>> E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>>> I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
>>> E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>>> E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>>> I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
>>> E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>>> E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>>> I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
>>> E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>>> E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>>>
>>> L716-EU-60 (RNDIS):
>>> T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 21 Spd=480 MxCh= 0
>>> D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
>>> P: Vendor=2cb7 ProdID=0001 Rev= 1.00
>>> S: Manufacturer=Fibocom,Incorporated
>>> S: Product=Fibocom Mobile Boardband
>>> S: SerialNumber=1234567890ABCDEF
>>> C:* #Ifs= 7 Cfg#= 1 Atr=e0 MxPwr=500mA
>>> A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=06 Prot=00
>>> I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
>>> E: Ad=87(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
>>> I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
>>> I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
>>> E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>>> E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>>> I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
>>> E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>>> E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>>> I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
>>> E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>>> E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>>> I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
>>> E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>>> E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>>> I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
>>> E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>>> E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>>> I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
>>> E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>>> E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>>>
>>> L716-EU-10 (ECM):
>>> T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 21 Spd=480 MxCh= 0
>>> D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
>>> P: Vendor=2cb7 ProdID=0001 Rev= 1.00
>>> S: Manufacturer=Fibocom,Incorporated
>>> S: Product=Fibocom Mobile Boardband
>>> S: SerialNumber=1234567890ABCDEF
>>> C:* #Ifs= 7 Cfg#= 1 Atr=e0 MxPwr=500mA
>>> A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=06 Prot=00
>>> I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
>>> E: Ad=87(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
>>> I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
>>> I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
>>> E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>>> E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>>> I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
>>> E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>>> E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>>> I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
>>> E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>>> E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>>> I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
>>> E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>>> E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>>> I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
>>> E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>>> E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>>> I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
>>> E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>>> E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>>>
>>> Signed-off-by: Victor Fragoso <[email protected]>
>>> ---
>>> drivers/usb/serial/option.c | 5 +++++
>>> 1 file changed, 5 insertions(+)
>>>
>>> diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
>>> index 45dcfaadaf98..4ba3dc352d65 100644
>>> --- a/drivers/usb/serial/option.c
>>> +++ b/drivers/usb/serial/option.c
>>> @@ -2262,6 +2262,11 @@ static const struct usb_device_id option_ids[] =
>>> {
>>> { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x01a2, 0xff)
>>> }, /* Fibocom FM101-GL (laptop MBIM) */
>>> { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x01a4,
>>> 0xff), /* Fibocom FM101-GL (laptop MBIM) */
>>> .driver_info = RSVD(4) },
>>> + { USB_DEVICE_AND_INTERFACE_INFO(0x2cb7, 0x0001, 0xff, 0xff,
>>> 0xff) }, /* Fibocom L71x */
>>> + { USB_DEVICE_AND_INTERFACE_INFO(0x2cb7, 0x0001, 0x0a, 0x00,
>>> 0xff) }, /* Fibocom L71x */
>>> + { USB_DEVICE_AND_INTERFACE_INFO(0x2cb7, 0x0100, 0xff, 0xff,
>>> 0xff) }, /* Fibocom L71x */
>>> + { USB_DEVICE_AND_INTERFACE_INFO(0x19d2, 0x0256, 0xff, 0xff,
>>> 0xff) }, /* Fibocom L71x */
>>> + { USB_DEVICE_AND_INTERFACE_INFO(0x19d2, 0x0579, 0xff, 0xff,
>>> 0xff) }, /* Fibocom L71x */
>>> { USB_DEVICE_INTERFACE_CLASS(0x2df3, 0x9d03, 0xff)
>>> }, /* LongSung M5710 */
>>> { USB_DEVICE_INTERFACE_CLASS(0x305a, 0x1404, 0xff)
>>> }, /* GosunCn GM500 RNDIS */
>>> { USB_DEVICE_INTERFACE_CLASS(0x305a, 0x1405, 0xff)
>>> }, /* GosunCn GM500 MBIM */
>>
>>
>> Hi Victor, thanks for the patch, there is unfortunately the following
>> errors in it:
>> The device list is sorted in ascending order based on vid:pid, you have
>> inserted all of your added Id's in the wrong place.
>>
>> 19d2:0579 is a ZTE device Id and should be placed among the other 19d2
>> devices.
>>
>> You have not included usb-devices output for 19d2:0256 and 2cb7:0100,
>> and I have strong reasons to believe that they should not be included in
>> the option driver.
>> If you are of another opinion then please show the usb-devices output
>> for them, otherwise remove them from the patch.
>>
>> You have added support for an interface with the attributes 0a/00/ff ,
>> there is no such interface in your provided usb-devices listing,
>> interface Class 0a does not even belong to the option driver.
>>
>> Thanks
>> Lars
>
> Hi Lars, sorry about the wrong order, I will correct it.
>
> But about the ZTE device ID, I belive that we should insert among
> Fibocom drivers because we are talking about a Fibocom module that is
> using an ZTE Chipset.
> So, this is exactly the same situation from Fibocom L610 IDs (0x1782,
> 0x4d10 / 0x1782, 0x4d11) that is using the Unisoc Chipset but were
> inserted among Fibocom drivers.
>
> And about the usb-devices output, let me explain better:
> I am a Field Application Enginner at Fibocom Brazil and I am using the
> IDs from our internal and official documentation.
> On this documents its suggested to add all this IDs because it will
> guarantee that can be used on all the variants devices from L71x series
> (that can change according to different part number, region support or
> network protocol).
> Unfortunately, I don't have all the modules variations available with
> me right now to test and share all the outputs.
>
> Can we continue with all the IDs that I have inserted?
> Or do you prefer to keep just the devices that I tested by myself until
> now?
>
> Victor Fragoso
Johan may have a different opinion from mine and he is the one to
decide, my take is that there is no value in having a minor part of the
list grouped by mfgr and the major part of the list sorted by USB Id.
We have also seen in the past that when a mfgr1 buys a chipset from
mfgr2 and then sells his product with mfgr2 Id instead of using one of
his own Id's then there is also not uncommon that mfgr3 is also buying
the same chipset without changing Id. Hence "Manufacturer name" is not
unique but the vid is..
The list should not be seen or used as a cross reference between
mfgr:product name and vid:pid, anyone who needs to search the driver
source to see if a device is supported ought to know its vid:pid so can
search on those and that works much better if the list is sorted by
vid:pid in ascending order. Personally I'd rather see a source without
all the unnecessary defines, only vid:pid based and with the
mfgr/product as an optional comment.
When adding Id's to the driver it is you who should know the devices you
are adding, don't add Id's if you have not personally confirmed their
interface composition and usage.
Those who told you add these Id's apparently also told you that there
are two versions of 2cb7:0001, one with ECM interfaces and one with
RNDIS interfaces but your usb-devices output show both to be identical..
There is no RNDIS interface in your listings, both of them will load
the cdc_ether driver.
br
Lars