Sharp's Spitz board still uses the legacy GPIO interface for controlling
a GPIO pin related to the USB host controller.
Convert this function to use the new GPIO descriptor interface.
Reviewed-by: Linus Walleij <[email protected]>
Signed-off-by: Duje Mihanović <[email protected]>
---
arch/arm/mach-pxa/spitz.c | 13 ++++++-------
drivers/usb/host/ohci-pxa27x.c | 7 +++++++
2 files changed, 13 insertions(+), 7 deletions(-)
diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c
index cc691b199429..535e2b2e997b 100644
--- a/arch/arm/mach-pxa/spitz.c
+++ b/arch/arm/mach-pxa/spitz.c
@@ -649,23 +649,22 @@ static inline void spitz_mmc_init(void) {}
* USB Host
******************************************************************************/
#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
+GPIO_LOOKUP_SINGLE(spitz_usb_host_gpio_table, "pxa27x-ohci", "gpio-pxa",
+ SPITZ_GPIO_USB_HOST, "usb-host", GPIO_ACTIVE_LOW);
+
static int spitz_ohci_init(struct device *dev)
{
- int err;
-
- err = gpio_request(SPITZ_GPIO_USB_HOST, "USB_HOST");
- if (err)
- return err;
+ gpiod_add_lookup_table(&spitz_usb_host_gpio_table);
/* Only Port 2 is connected, setup USB Port 2 Output Control Register */
UP2OCR = UP2OCR_HXS | UP2OCR_HXOE | UP2OCR_DPPDE | UP2OCR_DMPDE;
- return gpio_direction_output(SPITZ_GPIO_USB_HOST, 1);
+ return 0;
}
static void spitz_ohci_exit(struct device *dev)
{
- gpio_free(SPITZ_GPIO_USB_HOST);
+ gpiod_remove_lookup_table(&spitz_usb_host_gpio_table);
}
static struct pxaohci_platform_data spitz_ohci_platform_data = {
diff --git a/drivers/usb/host/ohci-pxa27x.c b/drivers/usb/host/ohci-pxa27x.c
index 357d9aee38a3..b70d452ca7c2 100644
--- a/drivers/usb/host/ohci-pxa27x.c
+++ b/drivers/usb/host/ohci-pxa27x.c
@@ -121,6 +121,7 @@ struct pxa27x_ohci {
void __iomem *mmio_base;
struct regulator *vbus[3];
bool vbus_enabled[3];
+ struct gpio_desc *usb_host;
};
#define to_pxa27x_ohci(hcd) (struct pxa27x_ohci *)(hcd_to_ohci(hcd)->priv)
@@ -447,6 +448,10 @@ static int ohci_hcd_pxa27x_probe(struct platform_device *pdev)
pxa_ohci = to_pxa27x_ohci(hcd);
pxa_ohci->clk = usb_clk;
pxa_ohci->mmio_base = (void __iomem *)hcd->regs;
+ pxa_ohci->usb_host = gpiod_get_optional(&pdev->dev, "usb-host", GPIOD_OUT_LOW);
+ if (IS_ERR(pxa_ohci->usb_host))
+ dev_warn(&pdev->dev, "failed to get USB host GPIO with %pe\n",
+ pxa_ohci->usb_host);
for (i = 0; i < 3; ++i) {
char name[6];
@@ -512,6 +517,8 @@ static void ohci_hcd_pxa27x_remove(struct platform_device *pdev)
for (i = 0; i < 3; ++i)
pxa27x_ohci_set_vbus_power(pxa_ohci, i, false);
+ gpiod_put(pxa_ohci->usb_host);
+
usb_put_hcd(hcd);
}
--
2.42.0
On Sun, Oct 1, 2023 at 5:13 PM Duje Mihanović <[email protected]> wrote:
>
> Sharp's Spitz board still uses the legacy GPIO interface for controlling
> a GPIO pin related to the USB host controller.
>
> Convert this function to use the new GPIO descriptor interface.
...
> + pxa_ohci->usb_host = gpiod_get_optional(&pdev->dev, "usb-host", GPIOD_OUT_LOW);
> + if (IS_ERR(pxa_ohci->usb_host))
> + dev_warn(&pdev->dev, "failed to get USB host GPIO with %pe\n",
> + pxa_ohci->usb_host);
Since you are using _optional() API, you need to bail out on the error
case and replace dev_warn() by dev_err(). I guess I already commented
on this. What is the rationale to not follow my comment?
--
With Best Regards,
Andy Shevchenko
On 10/1/2023 4:32 PM, Andy Shevchenko wrote:
>> + pxa_ohci->usb_host = gpiod_get_optional(&pdev->dev, "usb-host", GPIOD_OUT_LOW);
>> + if (IS_ERR(pxa_ohci->usb_host))
>> + dev_warn(&pdev->dev, "failed to get USB host GPIO with %pe\n",
>> + pxa_ohci->usb_host);
>
> Since you are using _optional() API, you need to bail out on the error
> case and replace dev_warn() by dev_err(). I guess I already commented
> on this. What is the rationale to not follow my comment?
I must have missed it, sorry about that. I'll be sure to do so in v5.
Regards,
Duje