The Synopsys Designware HDMI RX controller is an HDMI receiver controller that
is responsible to process digital data that comes from a phy. The final result
is a stream of raw video data that can then be connected to a video DMA, for
example, and transfered into RAM so that it can be displayed.
The controller + phy available in this series natively support all HDMI 1.4 and
HDMI 2.0 modes, including deep color. Although, the driver is quite in its
initial stage and unfortunatelly only non deep color modes are supported. Also,
audio is not yet supported in the driver (the controller has several audio
output interfaces).
Version 4 addresses review comments from Sylwester Nawrocki that were mainly
regarding the phy initialization and bindings in the DT. We switched to V4L2
async API so that we don't have to wait for phy to be initialized.
This series was tested in a FPGA platform.
Jose Abreu (4):
[media] platform: Add Synopsys Designware HDMI RX PHY e405 Driver
[media] platform: Add Synopsys Designware HDMI RX Controller Driver
MAINTAINERS: Add entry for Synopsys Designware HDMI drivers
dt-bindings: media: Document Synopsys Designware HDMI RX
Cc: Carlos Palminha <[email protected]>
Cc: Mauro Carvalho Chehab <[email protected]>
Cc: Hans Verkuil <[email protected]>
Cc: Rob Herring <[email protected]>
Cc: Mark Rutland <[email protected]>
Cc: Sylwester Nawrocki <[email protected]>
.../devicetree/bindings/media/snps,dw-hdmi-rx.txt | 70 +
MAINTAINERS | 7 +
drivers/media/platform/Kconfig | 2 +
drivers/media/platform/Makefile | 2 +
drivers/media/platform/dwc/Kconfig | 23 +
drivers/media/platform/dwc/Makefile | 2 +
drivers/media/platform/dwc/dw-hdmi-phy-e405.c | 832 +++++++++
drivers/media/platform/dwc/dw-hdmi-phy-e405.h | 63 +
drivers/media/platform/dwc/dw-hdmi-rx.c | 1862 ++++++++++++++++++++
drivers/media/platform/dwc/dw-hdmi-rx.h | 441 +++++
include/media/dwc/dw-hdmi-phy-pdata.h | 128 ++
include/media/dwc/dw-hdmi-rx-pdata.h | 97 +
12 files changed, 3529 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/snps,dw-hdmi-rx.txt
create mode 100644 drivers/media/platform/dwc/Kconfig
create mode 100644 drivers/media/platform/dwc/Makefile
create mode 100644 drivers/media/platform/dwc/dw-hdmi-phy-e405.c
create mode 100644 drivers/media/platform/dwc/dw-hdmi-phy-e405.h
create mode 100644 drivers/media/platform/dwc/dw-hdmi-rx.c
create mode 100644 drivers/media/platform/dwc/dw-hdmi-rx.h
create mode 100644 include/media/dwc/dw-hdmi-phy-pdata.h
create mode 100644 include/media/dwc/dw-hdmi-rx-pdata.h
--
1.9.1
This adds support for the Synopsys Designware HDMI RX PHY e405. This
phy receives and decodes HDMI video that is delivered to a controller.
Main features included in this driver are:
- Equalizer algorithm that chooses the phy best settings
according to the detected HDMI cable characteristics.
- Support for scrambling
- Support for HDMI 2.0 modes up to 6G (HDMI 4k@60Hz).
The driver was implemented as a standalone V4L2 subdevice and the
phy interface with the controller was implemented using V4L2 ioctls. I
do not know if this is the best option but it is not possible to use the
existing API functions directly as we need specific functions that will
be called by the controller at specific configuration stages.
There is also a bidirectional communication between controller and phy:
The phy must provide functions that the controller will call (i.e.
configuration functions) and the controller must provide read/write
callbacks, as well as other specific functions.
Signed-off-by: Jose Abreu <[email protected]>
Cc: Carlos Palminha <[email protected]>
Cc: Mauro Carvalho Chehab <[email protected]>
Cc: Hans Verkuil <[email protected]>
Cc: Sylwester Nawrocki <[email protected]>
Changes from v3:
- Use v4l2 async API (Sylwester)
- Use clock API (Sylwester)
- Add compatible string (Sylwester)
Changes from RFC:
- Remove a bunch of functions that can be collapsed into
a single config() function
- Add comments for the callbacks and structures (Hans)
---
drivers/media/platform/Kconfig | 2 +
drivers/media/platform/Makefile | 2 +
drivers/media/platform/dwc/Kconfig | 8 +
drivers/media/platform/dwc/Makefile | 1 +
drivers/media/platform/dwc/dw-hdmi-phy-e405.c | 832 ++++++++++++++++++++++++++
drivers/media/platform/dwc/dw-hdmi-phy-e405.h | 63 ++
include/media/dwc/dw-hdmi-phy-pdata.h | 128 ++++
7 files changed, 1036 insertions(+)
create mode 100644 drivers/media/platform/dwc/Kconfig
create mode 100644 drivers/media/platform/dwc/Makefile
create mode 100644 drivers/media/platform/dwc/dw-hdmi-phy-e405.c
create mode 100644 drivers/media/platform/dwc/dw-hdmi-phy-e405.h
create mode 100644 include/media/dwc/dw-hdmi-phy-pdata.h
diff --git a/drivers/media/platform/Kconfig b/drivers/media/platform/Kconfig
index 1313cd5..47d4a50 100644
--- a/drivers/media/platform/Kconfig
+++ b/drivers/media/platform/Kconfig
@@ -33,6 +33,8 @@ source "drivers/media/platform/omap/Kconfig"
source "drivers/media/platform/blackfin/Kconfig"
+source "drivers/media/platform/dwc/Kconfig"
+
config VIDEO_SH_VOU
tristate "SuperH VOU video output driver"
depends on MEDIA_CAMERA_SUPPORT
diff --git a/drivers/media/platform/Makefile b/drivers/media/platform/Makefile
index 9beadc7..e6a55fb 100644
--- a/drivers/media/platform/Makefile
+++ b/drivers/media/platform/Makefile
@@ -86,3 +86,5 @@ obj-$(CONFIG_VIDEO_MEDIATEK_MDP) += mtk-mdp/
obj-$(CONFIG_VIDEO_MEDIATEK_JPEG) += mtk-jpeg/
obj-$(CONFIG_VIDEO_QCOM_VENUS) += qcom/venus/
+
+obj-y += dwc/
diff --git a/drivers/media/platform/dwc/Kconfig b/drivers/media/platform/dwc/Kconfig
new file mode 100644
index 0000000..361d38d
--- /dev/null
+++ b/drivers/media/platform/dwc/Kconfig
@@ -0,0 +1,8 @@
+config VIDEO_DWC_HDMI_PHY_E405
+ tristate "Synopsys Designware HDMI RX PHY e405 driver"
+ depends on VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API
+ help
+ Support for Synopsys Designware HDMI RX PHY. Version is e405.
+
+ To compile this driver as a module, choose M here. The module
+ will be called dw-hdmi-phy-e405.
diff --git a/drivers/media/platform/dwc/Makefile b/drivers/media/platform/dwc/Makefile
new file mode 100644
index 0000000..fc3b62c
--- /dev/null
+++ b/drivers/media/platform/dwc/Makefile
@@ -0,0 +1 @@
+obj-$(CONFIG_VIDEO_DWC_HDMI_PHY_E405) += dw-hdmi-phy-e405.o
diff --git a/drivers/media/platform/dwc/dw-hdmi-phy-e405.c b/drivers/media/platform/dwc/dw-hdmi-phy-e405.c
new file mode 100644
index 0000000..d8856f6
--- /dev/null
+++ b/drivers/media/platform/dwc/dw-hdmi-phy-e405.c
@@ -0,0 +1,832 @@
+/*
+ * Synopsys Designware HDMI PHY E405 driver
+ *
+ * This Synopsys dw-phy-e405 software and associated documentation
+ * (hereinafter the "Software") is an unsupported proprietary work of
+ * Synopsys, Inc. unless otherwise expressly agreed to in writing between
+ * Synopsys and you. The Software IS NOT an item of Licensed Software or a
+ * Licensed Product under any End User Software License Agreement or
+ * Agreement for Licensed Products with Synopsys or any supplement thereto.
+ * Synopsys is a registered trademark of Synopsys, Inc. Other names included
+ * in the SOFTWARE may be the trademarks of their respective owners.
+ *
+ * The contents of this file are dual-licensed; you may select either version 2
+ * of the GNU General Public License (“GPL”) or the MIT license (“MIT”).
+ *
+ * Copyright (c) 2017 Synopsys, Inc. and/or its affiliates.
+ *
+ * THIS SOFTWARE IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING, BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE, AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR
+ * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT, OR OTHERWISE
+ * ARISING FROM, OUT OF, OR IN CONNECTION WITH THE SOFTWARE THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/types.h>
+#include <media/v4l2-async.h>
+#include <media/v4l2-subdev.h>
+#include <media/dwc/dw-hdmi-phy-pdata.h>
+#include "dw-hdmi-phy-e405.h"
+
+MODULE_AUTHOR("Jose Abreu <[email protected]>");
+MODULE_DESCRIPTION("Designware HDMI PHY e405 driver");
+MODULE_LICENSE("Dual MIT/GPL");
+
+#define PHY_EQ_WAIT_TIME_START 3
+#define PHY_EQ_SLEEP_TIME_CDR 30
+#define PHY_EQ_SLEEP_TIME_ACQ 1
+#define PHY_EQ_BOUNDSPREAD 20
+#define PHY_EQ_MIN_ACQ_STABLE 3
+#define PHY_EQ_ACC_LIMIT 360
+#define PHY_EQ_ACC_MIN_LIMIT 0
+#define PHY_EQ_MAX_SETTING 13
+#define PHY_EQ_SHORT_CABLE_SETTING 4
+#define PHY_EQ_ERROR_CABLE_SETTING 4
+#define PHY_EQ_MIN_SLOPE 50
+#define PHY_EQ_AVG_ACQ 5
+#define PHY_EQ_MINMAX_NTRIES 3
+#define PHY_EQ_EQUALIZED_COUNTER_VAL 512
+#define PHY_EQ_EQUALIZED_COUNTER_VAL_HDMI20 512
+#define PHY_EQ_MINMAX_MAXDIFF 4
+#define PHY_EQ_MINMAX_MAXDIFF_HDMI20 2
+#define PHY_EQ_FATBIT_MASK 0x0000
+#define PHY_EQ_FATBIT_MASK_4K 0x0c03
+#define PHY_EQ_FATBIT_MASK_HDMI20 0x0e03
+
+struct dw_phy_eq_ch {
+ u16 best_long_setting;
+ u8 valid_long_setting;
+ u16 best_short_setting;
+ u8 valid_short_setting;
+ u16 best_setting;
+ u16 acc;
+ u16 acq;
+ u16 last_acq;
+ u16 upper_bound_acq;
+ u16 lower_bound_acq;
+ u16 out_bound_acq;
+ u16 read_acq;
+};
+
+static const struct dw_phy_mpll_config {
+ u16 addr;
+ u16 val;
+} dw_phy_e405_mpll_cfg[] = {
+ { 0x27, 0x1B94 },
+ { 0x28, 0x16D2 },
+ { 0x29, 0x12D9 },
+ { 0x2A, 0x3249 },
+ { 0x2B, 0x3653 },
+ { 0x2C, 0x3436 },
+ { 0x2D, 0x124D },
+ { 0x2E, 0x0001 },
+ { 0xCE, 0x0505 },
+ { 0xCF, 0x0505 },
+ { 0xD0, 0x0000 },
+ { 0x00, 0x0000 },
+};
+
+struct dw_phy_dev {
+ struct device *dev;
+ struct dw_phy_pdata *config;
+ unsigned int version;
+ struct clk *clk;
+ u16 cfg_clk;
+ bool phy_enabled;
+ struct v4l2_subdev sd;
+ u16 mpll_status;
+ unsigned char color_depth;
+ bool hdmi2;
+ bool scrambling;
+ struct mutex lock;
+};
+
+static inline struct dw_phy_dev *to_dw_dev(struct v4l2_subdev *sd)
+{
+ return container_of(sd, struct dw_phy_dev, sd);
+}
+
+static void phy_write(struct dw_phy_dev *dw_dev, u16 val, u16 addr)
+{
+ void *arg = dw_dev->config->funcs_arg;
+
+ dw_dev->config->funcs->write(arg, val, addr);
+}
+
+static u16 phy_read(struct dw_phy_dev *dw_dev, u16 addr)
+{
+ void *arg = dw_dev->config->funcs_arg;
+
+ return dw_dev->config->funcs->read(arg, addr);
+}
+
+static void phy_reset(struct dw_phy_dev *dw_dev, int enable)
+{
+ void *arg = dw_dev->config->funcs_arg;
+
+ dw_dev->config->funcs->reset(arg, enable);
+}
+
+static void phy_pddq(struct dw_phy_dev *dw_dev, int enable)
+{
+ void *arg = dw_dev->config->funcs_arg;
+
+ dw_dev->config->funcs->pddq(arg, enable);
+}
+
+static void phy_svsmode(struct dw_phy_dev *dw_dev, int enable)
+{
+ void *arg = dw_dev->config->funcs_arg;
+
+ dw_dev->config->funcs->svsmode(arg, enable);
+}
+
+static void phy_zcal_reset(struct dw_phy_dev *dw_dev)
+{
+ void *arg = dw_dev->config->funcs_arg;
+
+ dw_dev->config->funcs->zcal_reset(arg);
+}
+
+static bool phy_zcal_done(struct dw_phy_dev *dw_dev)
+{
+ void *arg = dw_dev->config->funcs_arg;
+
+ return dw_dev->config->funcs->zcal_done(arg);
+}
+
+static bool phy_tmds_valid(struct dw_phy_dev *dw_dev)
+{
+ void *arg = dw_dev->config->funcs_arg;
+
+ return dw_dev->config->funcs->tmds_valid(arg);
+}
+
+static int dw_phy_eq_test(struct dw_phy_dev *dw_dev,
+ u16 *fat_bit_mask, int *min_max_length)
+{
+ u16 main_fsm_status, val;
+ int i;
+
+ for (i = 0; i < PHY_EQ_WAIT_TIME_START; i++) {
+ main_fsm_status = phy_read(dw_dev, PHY_MAINFSM_STATUS1);
+ if (main_fsm_status & 0x100)
+ break;
+ mdelay(PHY_EQ_SLEEP_TIME_CDR);
+ }
+
+ if (i == PHY_EQ_WAIT_TIME_START) {
+ dev_err(dw_dev->dev, "phy start conditions not achieved\n");
+ return -ETIMEDOUT;
+ }
+
+ if (main_fsm_status & 0x400) {
+ dev_err(dw_dev->dev, "invalid pll rate\n");
+ return -EINVAL;
+ }
+
+ val = (phy_read(dw_dev, PHY_CDR_CTRL_CNT) & 0x300) >> 8;
+ if (val == 0x1) {
+ /* HDMI 2.0 */
+ *fat_bit_mask = PHY_EQ_FATBIT_MASK_HDMI20;
+ *min_max_length = PHY_EQ_MINMAX_MAXDIFF_HDMI20;
+ dev_dbg(dw_dev->dev, "[EQUALIZER] using HDMI 2.0 values\n");
+ } else if (!(main_fsm_status & 0x600)) {
+ /* HDMI 1.4 (pll rate = 0) */
+ *fat_bit_mask = PHY_EQ_FATBIT_MASK_4K;
+ *min_max_length = PHY_EQ_MINMAX_MAXDIFF;
+ dev_dbg(dw_dev->dev, "[EQUALIZER] using HDMI 1.4@4k values\n");
+ } else {
+ /* HDMI 1.4 */
+ *fat_bit_mask = PHY_EQ_FATBIT_MASK;
+ *min_max_length = PHY_EQ_MINMAX_MAXDIFF;
+ dev_dbg(dw_dev->dev, "[EQUALIZER] using HDMI 1.4 values\n");
+ }
+
+ return 0;
+}
+
+static void dw_phy_eq_default(struct dw_phy_dev *dw_dev)
+{
+ phy_write(dw_dev, 0x08A8, PHY_CH0_EQ_CTRL1);
+ phy_write(dw_dev, 0x0020, PHY_CH0_EQ_CTRL2);
+ phy_write(dw_dev, 0x08A8, PHY_CH1_EQ_CTRL1);
+ phy_write(dw_dev, 0x0020, PHY_CH1_EQ_CTRL2);
+ phy_write(dw_dev, 0x08A8, PHY_CH2_EQ_CTRL1);
+ phy_write(dw_dev, 0x0020, PHY_CH2_EQ_CTRL2);
+}
+
+static void dw_phy_eq_single(struct dw_phy_dev *dw_dev)
+{
+ phy_write(dw_dev, 0x0211, PHY_CH0_EQ_CTRL1);
+ phy_write(dw_dev, 0x0211, PHY_CH1_EQ_CTRL1);
+ phy_write(dw_dev, 0x0211, PHY_CH2_EQ_CTRL1);
+}
+
+static void dw_phy_eq_equal_setting(struct dw_phy_dev *dw_dev,
+ u16 lock_vector)
+{
+ phy_write(dw_dev, lock_vector, PHY_CH0_EQ_CTRL4);
+ phy_write(dw_dev, 0x0024, PHY_CH0_EQ_CTRL2);
+ phy_write(dw_dev, 0x0026, PHY_CH0_EQ_CTRL2);
+ phy_read(dw_dev, PHY_CH0_EQ_STATUS2);
+ phy_write(dw_dev, lock_vector, PHY_CH1_EQ_CTRL4);
+ phy_write(dw_dev, 0x0024, PHY_CH1_EQ_CTRL2);
+ phy_write(dw_dev, 0x0026, PHY_CH1_EQ_CTRL2);
+ phy_read(dw_dev, PHY_CH1_EQ_STATUS2);
+ phy_write(dw_dev, lock_vector, PHY_CH2_EQ_CTRL4);
+ phy_write(dw_dev, 0x0024, PHY_CH2_EQ_CTRL2);
+ phy_write(dw_dev, 0x0026, PHY_CH2_EQ_CTRL2);
+ phy_read(dw_dev, PHY_CH2_EQ_STATUS2);
+}
+
+static void dw_phy_eq_equal_setting_ch0(struct dw_phy_dev *dw_dev,
+ u16 lock_vector)
+{
+ phy_write(dw_dev, lock_vector, PHY_CH0_EQ_CTRL4);
+ phy_write(dw_dev, 0x0024, PHY_CH0_EQ_CTRL2);
+ phy_write(dw_dev, 0x0026, PHY_CH0_EQ_CTRL2);
+ phy_read(dw_dev, PHY_CH0_EQ_STATUS2);
+}
+
+static void dw_phy_eq_equal_setting_ch1(struct dw_phy_dev *dw_dev,
+ u16 lock_vector)
+{
+ phy_write(dw_dev, lock_vector, PHY_CH1_EQ_CTRL4);
+ phy_write(dw_dev, 0x0024, PHY_CH1_EQ_CTRL2);
+ phy_write(dw_dev, 0x0026, PHY_CH1_EQ_CTRL2);
+ phy_read(dw_dev, PHY_CH1_EQ_STATUS2);
+}
+
+static void dw_phy_eq_equal_setting_ch2(struct dw_phy_dev *dw_dev,
+ u16 lock_vector)
+{
+ phy_write(dw_dev, lock_vector, PHY_CH2_EQ_CTRL4);
+ phy_write(dw_dev, 0x0024, PHY_CH2_EQ_CTRL2);
+ phy_write(dw_dev, 0x0026, PHY_CH2_EQ_CTRL2);
+ phy_read(dw_dev, PHY_CH2_EQ_STATUS2);
+}
+
+static void dw_phy_eq_auto_calib(struct dw_phy_dev *dw_dev)
+{
+ phy_write(dw_dev, 0x1809, PHY_MAINFSM_CTRL);
+ phy_write(dw_dev, 0x1819, PHY_MAINFSM_CTRL);
+ phy_write(dw_dev, 0x1809, PHY_MAINFSM_CTRL);
+}
+
+static void dw_phy_eq_init_vars(struct dw_phy_eq_ch *ch)
+{
+ ch->acc = 0;
+ ch->acq = 0;
+ ch->last_acq = 0;
+ ch->valid_long_setting = 0;
+ ch->valid_short_setting = 0;
+ ch->best_setting = PHY_EQ_SHORT_CABLE_SETTING;
+}
+
+static bool dw_phy_eq_acquire_early_cnt(struct dw_phy_dev *dw_dev,
+ u16 setting, u16 acq, struct dw_phy_eq_ch *ch0,
+ struct dw_phy_eq_ch *ch1, struct dw_phy_eq_ch *ch2)
+{
+ u16 lock_vector = 0x1;
+ int i;
+
+ lock_vector <<= setting;
+ ch0->out_bound_acq = 0;
+ ch1->out_bound_acq = 0;
+ ch2->out_bound_acq = 0;
+ ch0->acq = 0;
+ ch1->acq = 0;
+ ch2->acq = 0;
+
+ dw_phy_eq_equal_setting(dw_dev, lock_vector);
+ dw_phy_eq_auto_calib(dw_dev);
+
+ mdelay(PHY_EQ_SLEEP_TIME_CDR);
+ if (!phy_tmds_valid(dw_dev))
+ dev_dbg(dw_dev->dev, "TMDS is NOT valid\n");
+
+ ch0->read_acq = phy_read(dw_dev, PHY_CH0_EQ_STATUS3);
+ ch1->read_acq = phy_read(dw_dev, PHY_CH1_EQ_STATUS3);
+ ch2->read_acq = phy_read(dw_dev, PHY_CH2_EQ_STATUS3);
+
+ ch0->acq += ch0->read_acq;
+ ch1->acq += ch1->read_acq;
+ ch2->acq += ch2->read_acq;
+
+ ch0->upper_bound_acq = ch0->read_acq + PHY_EQ_BOUNDSPREAD;
+ ch0->lower_bound_acq = ch0->read_acq - PHY_EQ_BOUNDSPREAD;
+ ch1->upper_bound_acq = ch1->read_acq + PHY_EQ_BOUNDSPREAD;
+ ch1->lower_bound_acq = ch1->read_acq - PHY_EQ_BOUNDSPREAD;
+ ch2->upper_bound_acq = ch2->read_acq + PHY_EQ_BOUNDSPREAD;
+ ch2->lower_bound_acq = ch2->read_acq - PHY_EQ_BOUNDSPREAD;
+
+ for (i = 1; i < acq; i++) {
+ dw_phy_eq_auto_calib(dw_dev);
+ mdelay(PHY_EQ_SLEEP_TIME_ACQ);
+
+ if ((ch0->read_acq > ch0->upper_bound_acq) ||
+ (ch0->read_acq < ch0->lower_bound_acq))
+ ch0->out_bound_acq++;
+ if ((ch1->read_acq > ch1->upper_bound_acq) ||
+ (ch1->read_acq < ch1->lower_bound_acq))
+ ch1->out_bound_acq++;
+ if ((ch2->read_acq > ch2->upper_bound_acq) ||
+ (ch2->read_acq < ch1->lower_bound_acq))
+ ch2->out_bound_acq++;
+
+ if (i == PHY_EQ_MIN_ACQ_STABLE) {
+ if ((ch0->out_bound_acq == 0) &&
+ (ch1->out_bound_acq == 0) &&
+ (ch2->out_bound_acq == 0)) {
+ acq = 3;
+ break;
+ }
+ }
+
+ ch0->read_acq = phy_read(dw_dev, PHY_CH0_EQ_STATUS3);
+ ch1->read_acq = phy_read(dw_dev, PHY_CH1_EQ_STATUS3);
+ ch2->read_acq = phy_read(dw_dev, PHY_CH2_EQ_STATUS3);
+
+ ch0->acq += ch0->read_acq;
+ ch1->acq += ch1->read_acq;
+ ch2->acq += ch2->read_acq;
+ }
+
+ ch0->acq = ch0->acq / acq;
+ ch1->acq = ch1->acq / acq;
+ ch2->acq = ch2->acq / acq;
+
+ return true;
+}
+
+static int dw_phy_eq_test_type(u16 setting, bool tmds_valid,
+ struct dw_phy_eq_ch *ch)
+{
+ u16 step_slope = 0;
+
+ if ((ch->acq < ch->last_acq) && tmds_valid) {
+ /* Long cable equalization */
+ ch->acc += ch->last_acq - ch->acq;
+ if ((ch->valid_long_setting == 0) && (ch->acq < 512) &&
+ (ch->acc > 0)) {
+ ch->best_long_setting = setting;
+ ch->valid_long_setting = 1;
+ }
+ step_slope = ch->last_acq - ch->acq;
+ }
+
+ if (tmds_valid && (ch->valid_short_setting == 0)) {
+ /* Short cable equalization */
+ if ((setting < PHY_EQ_SHORT_CABLE_SETTING) &&
+ (ch->acq < PHY_EQ_EQUALIZED_COUNTER_VAL)) {
+ ch->best_short_setting= setting;
+ ch->valid_short_setting = 1;
+ }
+
+ if (setting == PHY_EQ_SHORT_CABLE_SETTING) {
+ ch->best_short_setting = PHY_EQ_SHORT_CABLE_SETTING;
+ ch->valid_short_setting = 1;
+ }
+ }
+
+ if (ch->valid_long_setting && (ch->acc > PHY_EQ_ACC_LIMIT)) {
+ ch->best_setting = ch->best_long_setting;
+ return 1;
+ }
+
+ if ((setting == PHY_EQ_MAX_SETTING) && (ch->acc < PHY_EQ_ACC_LIMIT) &&
+ ch->valid_short_setting) {
+ ch->best_setting = ch->best_short_setting;
+ return 2;
+ }
+
+ if ((setting == PHY_EQ_MAX_SETTING) && tmds_valid &&
+ (ch->acc > PHY_EQ_ACC_LIMIT) &&
+ (step_slope > PHY_EQ_MIN_SLOPE)) {
+ ch->best_setting = PHY_EQ_MAX_SETTING;
+ return 3;
+ }
+
+ if (setting == PHY_EQ_MAX_SETTING) {
+ ch->best_setting = PHY_EQ_ERROR_CABLE_SETTING;
+ return 255;
+ }
+
+ return 0;
+}
+
+static bool dw_phy_eq_setting_finder(struct dw_phy_dev *dw_dev, u16 acq,
+ struct dw_phy_eq_ch *ch0, struct dw_phy_eq_ch *ch1,
+ struct dw_phy_eq_ch *ch2)
+{
+ u16 act = 0;
+ int ret_ch0 = 0, ret_ch1 = 0, ret_ch2 = 0;
+ bool tmds_valid = false;
+
+ dw_phy_eq_init_vars(ch0);
+ dw_phy_eq_init_vars(ch1);
+ dw_phy_eq_init_vars(ch2);
+
+ tmds_valid = dw_phy_eq_acquire_early_cnt(dw_dev, act, acq,
+ ch0, ch1, ch2);
+
+ while ((ret_ch0 == 0) || (ret_ch1 == 0) || (ret_ch2 == 0)) {
+ act++;
+
+ ch0->last_acq = ch0->acq;
+ ch1->last_acq = ch1->acq;
+ ch2->last_acq = ch2->acq;
+
+ tmds_valid = dw_phy_eq_acquire_early_cnt(dw_dev, act, acq,
+ ch0, ch1, ch2);
+
+ if (!ret_ch0)
+ ret_ch0 = dw_phy_eq_test_type(act, tmds_valid, ch0);
+ if (!ret_ch1)
+ ret_ch1 = dw_phy_eq_test_type(act, tmds_valid, ch1);
+ if (!ret_ch2)
+ ret_ch2 = dw_phy_eq_test_type(act, tmds_valid, ch2);
+ }
+
+ if ((ret_ch0 == 255) || (ret_ch1 == 255) || (ret_ch2 == 255))
+ return false;
+ return true;
+}
+
+static bool dw_phy_eq_maxvsmin(u16 ch0_setting, u16 ch1_setting,
+ u16 ch2_setting, u16 min_max_length)
+{
+ u16 min = ch0_setting, max = ch0_setting;
+
+ if (ch1_setting > max)
+ max = ch1_setting;
+ if (ch2_setting > max)
+ max = ch2_setting;
+ if (ch1_setting < min)
+ min = ch1_setting;
+ if (ch2_setting < min)
+ min = ch2_setting;
+
+ if ((max - min) > min_max_length)
+ return false;
+ return true;
+}
+
+static int dw_phy_eq_init(struct dw_phy_dev *dw_dev, u16 acq, bool force)
+{
+ struct dw_phy_eq_ch ch0, ch1, ch2;
+ u16 fat_bit_mask, lock_vector = 0x1;
+ int min_max_length, i, ret = 0;
+ u16 mpll_status;
+
+ if (dw_dev->version < 401)
+ return ret;
+ if (!dw_dev->phy_enabled)
+ return -EINVAL;
+
+ mpll_status = phy_read(dw_dev, PHY_CLK_MPLL_STATUS);
+ if (mpll_status == dw_dev->mpll_status && !force)
+ return ret;
+ dw_dev->mpll_status = mpll_status;
+
+ phy_write(dw_dev, 0x00, PHY_MAINFSM_OVR2);
+ phy_write(dw_dev, 0x00, PHY_CH0_EQ_CTRL3);
+ phy_write(dw_dev, 0x00, PHY_CH1_EQ_CTRL3);
+ phy_write(dw_dev, 0x00, PHY_CH2_EQ_CTRL3);
+
+ ret = dw_phy_eq_test(dw_dev, &fat_bit_mask, &min_max_length);
+ if (ret) {
+ if (ret == -EINVAL) /* Means equalizer is not needed */
+ ret = 0;
+
+ /* Do not change values if we don't have clock */
+ if (ret != -ETIMEDOUT) {
+ dw_phy_eq_default(dw_dev);
+ phy_pddq(dw_dev, 1);
+ phy_pddq(dw_dev, 0);
+ }
+ } else {
+ dw_phy_eq_single(dw_dev);
+ dw_phy_eq_equal_setting(dw_dev, 0x0001);
+ phy_write(dw_dev, fat_bit_mask, PHY_CH0_EQ_CTRL6);
+ phy_write(dw_dev, fat_bit_mask, PHY_CH1_EQ_CTRL6);
+ phy_write(dw_dev, fat_bit_mask, PHY_CH2_EQ_CTRL6);
+
+ for (i = 0; i < PHY_EQ_MINMAX_NTRIES; i++) {
+ if (dw_phy_eq_setting_finder(dw_dev, acq,
+ &ch0, &ch1, &ch2)) {
+ if (dw_phy_eq_maxvsmin(ch0.best_setting,
+ ch1.best_setting,
+ ch2.best_setting,
+ min_max_length))
+ break;
+ }
+
+ ch0.best_setting = PHY_EQ_ERROR_CABLE_SETTING;
+ ch1.best_setting = PHY_EQ_ERROR_CABLE_SETTING;
+ ch2.best_setting = PHY_EQ_ERROR_CABLE_SETTING;
+ }
+
+ dev_dbg(dw_dev->dev, "equalizer settings: "
+ "ch0=0x%x, ch1=0x%x, ch1=0x%x\n",
+ ch0.best_setting, ch1.best_setting,
+ ch2.best_setting);
+
+ if (i == PHY_EQ_MINMAX_NTRIES)
+ ret = -EINVAL;
+
+ lock_vector = 0x1;
+ lock_vector <<= ch0.best_setting;
+ dw_phy_eq_equal_setting_ch0(dw_dev, lock_vector);
+
+ lock_vector = 0x1;
+ lock_vector <<= ch1.best_setting;
+ dw_phy_eq_equal_setting_ch1(dw_dev, lock_vector);
+
+ lock_vector = 0x1;
+ lock_vector <<= ch2.best_setting;
+ dw_phy_eq_equal_setting_ch2(dw_dev, lock_vector);
+
+ phy_pddq(dw_dev, 1);
+ phy_pddq(dw_dev, 0);
+ }
+
+ return ret;
+}
+
+static int dw_phy_config(struct dw_phy_dev *dw_dev, unsigned char color_depth,
+ bool hdmi2, bool scrambling)
+{
+ const struct dw_phy_mpll_config *mpll_cfg = dw_phy_e405_mpll_cfg;
+ struct device *dev = dw_dev->dev;
+ int timeout = 100;
+ u16 val, res_idx;
+ bool zcal_done;
+
+ dev_dbg(dev, "%s: color_depth=%d, hdmi2=%d, scrambling=%d, cfg_clk=%d\n",
+ __func__, color_depth, hdmi2, scrambling, dw_dev->cfg_clk);
+
+ switch (color_depth) {
+ case 8:
+ res_idx = 0x0;
+ break;
+ case 10:
+ res_idx = 0x1;
+ break;
+ case 12:
+ res_idx = 0x2;
+ break;
+ case 16:
+ res_idx = 0x3;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ phy_reset(dw_dev, 1);
+ phy_pddq(dw_dev, 1);
+ phy_svsmode(dw_dev, 1);
+
+ phy_zcal_reset(dw_dev);
+ do {
+ udelay(1000);
+ zcal_done = phy_zcal_done(dw_dev);
+ } while (!zcal_done && timeout--);
+
+ if (!zcal_done) {
+ dev_err(dw_dev->dev, "Zcal calibration failed\n");
+ return -ETIMEDOUT;
+ }
+
+ phy_reset(dw_dev, 0);
+
+ /* CMU */
+ val = (0x08 << 10) | (0x01 << 9);
+ val |= (dw_dev->cfg_clk * 4) & GENMASK(8, 0);
+ phy_write(dw_dev, val, PHY_CMU_CONFIG);
+
+ /* Color Depth and enable fast switching */
+ val = phy_read(dw_dev, PHY_SYSTEM_CONFIG);
+ val = (val & ~0x60) | (res_idx << 5) | BIT(11);
+ phy_write(dw_dev, val, PHY_SYSTEM_CONFIG);
+
+ /* MPLL */
+ for (; mpll_cfg->addr != 0x0; mpll_cfg++)
+ phy_write(dw_dev, mpll_cfg->val, mpll_cfg->addr);
+
+ /* Operation for data rates between 3.4Gbps and 6Gbps */
+ val = phy_read(dw_dev, PHY_CDR_CTRL_CNT);
+ if (hdmi2)
+ val |= BIT(8);
+ else
+ val &= ~BIT(8);
+ phy_write(dw_dev, val, PHY_CDR_CTRL_CNT);
+
+ /* Scrambling */
+ val = phy_read(dw_dev, PHY_OVL_PROT_CTRL);
+ if (scrambling)
+ val |= GENMASK(7,6);
+ else
+ val &= ~GENMASK(7,6);
+ phy_write(dw_dev, val, PHY_OVL_PROT_CTRL);
+
+ /* Enable phy */
+ phy_pddq(dw_dev, 0);
+
+ dw_dev->color_depth = color_depth;
+ dw_dev->hdmi2 = hdmi2;
+ dw_dev->scrambling = scrambling;
+ return 0;
+}
+
+static int dw_phy_enable(struct dw_phy_dev *dw_dev, unsigned char color_depth,
+ bool hdmi2, bool scrambling)
+{
+ int ret;
+
+ if (dw_dev->phy_enabled &&
+ dw_dev->color_depth == color_depth &&
+ dw_dev->hdmi2 == hdmi2 &&
+ dw_dev->scrambling == scrambling)
+ return 0;
+
+ ret = dw_phy_config(dw_dev, color_depth, hdmi2, scrambling);
+ if (ret)
+ return ret;
+
+ phy_reset(dw_dev, 0);
+ phy_pddq(dw_dev, 0);
+ dw_dev->phy_enabled = true;
+ return 0;
+}
+
+static void dw_phy_disable(struct dw_phy_dev *dw_dev)
+{
+ if (!dw_dev->phy_enabled)
+ return;
+
+ phy_reset(dw_dev, 1);
+ phy_pddq(dw_dev, 1);
+ phy_svsmode(dw_dev, 0);
+ dw_dev->mpll_status = 0xFFFF;
+ dw_dev->phy_enabled = false;
+}
+
+static long dw_phy_ioctl(struct v4l2_subdev *sd, unsigned int cmd, void *arg)
+{
+ struct dw_phy_dev *dw_dev = to_dw_dev(sd);
+ struct dw_phy_config_command *ccmd;
+ struct dw_phy_eq_command *ecmd;
+ int ret = 0;
+
+ dev_dbg(dw_dev->dev, "%s: cmd=%d\n", __func__, cmd);
+
+ mutex_lock(&dw_dev->lock);
+ switch (cmd) {
+ case DW_PHY_IOCTL_EQ_INIT:
+ ecmd = (struct dw_phy_eq_command *)arg;
+ ecmd->result = dw_phy_eq_init(dw_dev, ecmd->nacq, ecmd->force);
+ break;
+ case DW_PHY_IOCTL_CONFIG:
+ ccmd = (struct dw_phy_config_command *)arg;
+ ccmd->result = dw_phy_enable(dw_dev, ccmd->color_depth,
+ ccmd->hdmi2, ccmd->scrambling);
+ break;
+ default:
+ ret = -ENOIOCTLCMD;
+ break;
+ }
+ mutex_unlock(&dw_dev->lock);
+
+ return ret;
+}
+
+static int dw_phy_s_power(struct v4l2_subdev *sd, int on)
+{
+ struct dw_phy_dev *dw_dev = to_dw_dev(sd);
+
+ dev_dbg(dw_dev->dev, "%s: on=%d\n", __func__, on);
+
+ mutex_lock(&dw_dev->lock);
+ if (!on)
+ dw_phy_disable(dw_dev);
+ mutex_unlock(&dw_dev->lock);
+ return 0;
+}
+
+static const struct v4l2_subdev_core_ops dw_phy_core_ops = {
+ .ioctl = dw_phy_ioctl,
+ .s_power = dw_phy_s_power,
+};
+
+static const struct v4l2_subdev_ops dw_phy_sd_ops = {
+ .core = &dw_phy_core_ops,
+};
+
+static int dw_phy_probe(struct platform_device *pdev)
+{
+ struct dw_phy_pdata *pdata = pdev->dev.platform_data;
+ struct device *dev = &pdev->dev;
+ struct dw_phy_dev *dw_dev;
+ struct v4l2_subdev *sd;
+ int ret;
+
+ dev_dbg(dev, "probe start\n");
+
+ /* Resource allocation */
+ dw_dev = devm_kzalloc(dev, sizeof(*dw_dev), GFP_KERNEL);
+ if (!dw_dev)
+ return -ENOMEM;
+
+ /* Resource initialization */
+ if (!pdata) {
+ dev_err(dev, "no platform data suplied\n");
+ return -EINVAL;
+ }
+
+ dw_dev->dev = dev;
+ dw_dev->config = pdata;
+ dw_dev->version = 405;
+ mutex_init(&dw_dev->lock);
+
+ /* Get config clock value */
+ dw_dev->clk = devm_clk_get(dev, "cfg-clk");
+ if (IS_ERR(dw_dev->clk)) {
+ dev_err(dev, "failed to get cfg-clk\n");
+ return PTR_ERR(dw_dev->clk);
+ }
+
+ ret = clk_prepare_enable(dw_dev->clk);
+ if (ret) {
+ dev_err(dev, "failed to enable cfg-clk\n");
+ return ret;
+ }
+
+ dw_dev->cfg_clk = clk_get_rate(dw_dev->clk) / 1000000;
+ if (!dw_dev->cfg_clk) {
+ dev_err(dev, "invalid cfg-clk frequency\n");
+ ret = -EINVAL;
+ goto err_clk;
+ }
+
+ /* V4L2 initialization */
+ sd = &dw_dev->sd;
+ v4l2_subdev_init(sd, &dw_phy_sd_ops);
+ strlcpy(sd->name, dev_name(dev), sizeof(sd->name));
+ sd->dev = dev;
+
+ /* Force phy disabling */
+ dw_dev->phy_enabled = true;
+ dw_phy_disable(dw_dev);
+
+ /* Register subdev */
+ ret = v4l2_async_register_subdev(sd);
+ if (ret) {
+ dev_err(dev, "failed to register subdev\n");
+ goto err_clk;
+ }
+
+ /* All done */
+ dev_set_drvdata(dev, sd);
+ dev_info(dev, "driver probed (cfg-clk=%d)\n", dw_dev->cfg_clk);
+ return 0;
+
+err_clk:
+ clk_disable_unprepare(dw_dev->clk);
+ return ret;
+}
+
+static int dw_phy_remove(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct v4l2_subdev *sd = dev_get_drvdata(dev);
+ struct dw_phy_dev *dw_dev = to_dw_dev(sd);
+
+ v4l2_async_unregister_subdev(sd);
+ clk_disable_unprepare(dw_dev->clk);
+ dev_info(dev, "driver removed\n");
+ return 0;
+}
+
+static const struct of_device_id dw_hdmi_phy_e405_id[] = {
+ { .compatible = "snps,dw-hdmi-phy-e405" },
+ { },
+};
+MODULE_DEVICE_TABLE(of, dw_hdmi_phy_e405_id);
+
+static struct platform_driver dw_phy_e405_driver = {
+ .probe = dw_phy_probe,
+ .remove = dw_phy_remove,
+ .driver = {
+ .name = DW_PHY_E405_DRVNAME,
+ .of_match_table = dw_hdmi_phy_e405_id,
+ }
+};
+module_platform_driver(dw_phy_e405_driver);
diff --git a/drivers/media/platform/dwc/dw-hdmi-phy-e405.h b/drivers/media/platform/dwc/dw-hdmi-phy-e405.h
new file mode 100644
index 0000000..3e6c8da
--- /dev/null
+++ b/drivers/media/platform/dwc/dw-hdmi-phy-e405.h
@@ -0,0 +1,63 @@
+/*
+ * Synopsys Designware HDMI PHY E405 driver
+ *
+ * This Synopsys dw-phy-e405 software and associated documentation
+ * (hereinafter the "Software") is an unsupported proprietary work of
+ * Synopsys, Inc. unless otherwise expressly agreed to in writing between
+ * Synopsys and you. The Software IS NOT an item of Licensed Software or a
+ * Licensed Product under any End User Software License Agreement or
+ * Agreement for Licensed Products with Synopsys or any supplement thereto.
+ * Synopsys is a registered trademark of Synopsys, Inc. Other names included
+ * in the SOFTWARE may be the trademarks of their respective owners.
+ *
+ * The contents of this file are dual-licensed; you may select either version 2
+ * of the GNU General Public License (“GPL”) or the MIT license (“MIT”).
+ *
+ * Copyright (c) 2017 Synopsys, Inc. and/or its affiliates.
+ *
+ * THIS SOFTWARE IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING, BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE, AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR
+ * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT, OR OTHERWISE
+ * ARISING FROM, OUT OF, OR IN CONNECTION WITH THE SOFTWARE THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#ifndef __DW_HDMI_PHY_E405_H__
+#define __DW_HDMI_PHY_E405_H__
+
+#define PHY_CMU_CONFIG 0x02
+#define PHY_SYSTEM_CONFIG 0x03
+#define PHY_MAINFSM_CTRL 0x05
+#define PHY_MAINFSM_OVR2 0x08
+#define PHY_MAINFSM_STATUS1 0x09
+#define PHY_OVL_PROT_CTRL 0x0D
+#define PHY_CDR_CTRL_CNT 0x0E
+#define PHY_CLK_MPLL_STATUS 0x2F
+#define PHY_CH0_EQ_CTRL1 0x32
+#define PHY_CH0_EQ_CTRL2 0x33
+#define PHY_CH0_EQ_STATUS 0x34
+#define PHY_CH0_EQ_CTRL3 0x3E
+#define PHY_CH0_EQ_CTRL4 0x3F
+#define PHY_CH0_EQ_STATUS2 0x40
+#define PHY_CH0_EQ_STATUS3 0x42
+#define PHY_CH0_EQ_CTRL6 0x43
+#define PHY_CH1_EQ_CTRL1 0x52
+#define PHY_CH1_EQ_CTRL2 0x53
+#define PHY_CH1_EQ_STATUS 0x54
+#define PHY_CH1_EQ_CTRL3 0x5E
+#define PHY_CH1_EQ_CTRL4 0x5F
+#define PHY_CH1_EQ_STATUS2 0x60
+#define PHY_CH1_EQ_STATUS3 0x62
+#define PHY_CH1_EQ_CTRL6 0x63
+#define PHY_CH2_EQ_CTRL1 0x72
+#define PHY_CH2_EQ_CTRL2 0x73
+#define PHY_CH2_EQ_STATUS 0x74
+#define PHY_CH2_EQ_CTRL3 0x7E
+#define PHY_CH2_EQ_CTRL4 0x7F
+#define PHY_CH2_EQ_STATUS2 0x80
+#define PHY_CH2_EQ_STATUS3 0x82
+#define PHY_CH2_EQ_CTRL6 0x83
+
+#endif /* __DW_HDMI_PHY_E405_H__ */
diff --git a/include/media/dwc/dw-hdmi-phy-pdata.h b/include/media/dwc/dw-hdmi-phy-pdata.h
new file mode 100644
index 0000000..e533eec
--- /dev/null
+++ b/include/media/dwc/dw-hdmi-phy-pdata.h
@@ -0,0 +1,128 @@
+/*
+ * Synopsys Designware HDMI PHY platform data
+ *
+ * This Synopsys dw-hdmi-phy software and associated documentation
+ * (hereinafter the "Software") is an unsupported proprietary work of
+ * Synopsys, Inc. unless otherwise expressly agreed to in writing between
+ * Synopsys and you. The Software IS NOT an item of Licensed Software or a
+ * Licensed Product under any End User Software License Agreement or
+ * Agreement for Licensed Products with Synopsys or any supplement thereto.
+ * Synopsys is a registered trademark of Synopsys, Inc. Other names included
+ * in the SOFTWARE may be the trademarks of their respective owners.
+ *
+ * The contents of this file are dual-licensed; you may select either version 2
+ * of the GNU General Public License (“GPL”) or the MIT license (“MIT”).
+ *
+ * Copyright (c) 2017 Synopsys, Inc. and/or its affiliates.
+ *
+ * THIS SOFTWARE IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING, BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE, AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR
+ * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT, OR OTHERWISE
+ * ARISING FROM, OUT OF, OR IN CONNECTION WITH THE SOFTWARE THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#ifndef __DW_HDMI_PHY_PDATA_H__
+#define __DW_HDMI_PHY_PDATA_H__
+
+#define DW_PHY_E405_DRVNAME "dw-hdmi-phy-e405"
+
+#define DW_PHY_IOCTL_EQ_INIT _IOW('R',1,int)
+#define DW_PHY_IOCTL_CONFIG _IOW('R',2,int)
+
+/**
+ * struct dw_phy_eq_command - Command arguments for HDMI PHY equalizer
+ * algorithm.
+ *
+ * @nacq: Number of acquisitions to get.
+ *
+ * @force: Force equalizer algorithm even if the MPLL status didn't change
+ * from previous run.
+ *
+ * @result: Result from the equalizer algorithm. Shall be zero if equalizer
+ * ran with success or didn't run because the video mode does not need
+ * equalizer (for low clock values).
+ */
+struct dw_phy_eq_command {
+ u16 nacq;
+ bool force;
+ int result;
+};
+
+/**
+ * struct dw_phy_config_command - Command arguments for HDMI PHY configuration
+ * function.
+ *
+ * @color_depth: Color depth of the video mode being received.
+ *
+ * @hdmi2: Must be set to true if the video mode being received has a data
+ * rate above 3.4Gbps (generally HDMI 2.0 video modes, like 4k@60Hz).
+ *
+ * @scrambling: Must be set to true if scrambling is currently enabled.
+ * Scrambling is enabled by source when SCDC scrambling_en field is set to 1.
+ *
+ * @result: Result from the configuration function. Shall be zero if phy was
+ * configured with success.
+ */
+struct dw_phy_config_command {
+ unsigned char color_depth;
+ bool hdmi2;
+ bool scrambling;
+ int result;
+};
+
+/**
+ * struct dw_phy_funcs - Set of callbacks used to communicate between phy
+ * and hdmi controller. Controller must correctly fill these callbacks
+ * before probbing the phy driver.
+ *
+ * @write: write callback. Write value 'val' into address 'addr' of phy.
+ *
+ * @read: read callback. Read address 'addr' and return the value.
+ *
+ * @reset: reset callback. Activate phy reset. Active high.
+ *
+ * @pddq: pddq callback. Activate phy configuration mode. Active high.
+ *
+ * @svsmode: svsmode callback. Activate phy retention mode. Active low.
+ *
+ * @zcal_reset: zcal reset callback. Restart the impedance calibration
+ * procedure. Active high. This is only used in prototyping and not in real
+ * ASIC. Callback shall be empty (but non NULL) in ASIC cases.
+ *
+ * @zcal_done: zcal done callback. Return the current status of impedance
+ * calibration procedure. This is only used in prototyping and not in real
+ * ASIC. Shall return always true in ASIC cases.
+ *
+ * @tmds_valid: TMDS valid callback. Return the current status of TMDS signal
+ * that comes from phy and feeds controller. This is read from a controller
+ * register.
+ */
+struct dw_phy_funcs {
+ void (*write) (void *arg, u16 val, u16 addr);
+ u16 (*read) (void *arg, u16 addr);
+ void (*reset) (void *arg, int enable);
+ void (*pddq) (void *arg, int enable);
+ void (*svsmode) (void *arg, int enable);
+ void (*zcal_reset) (void *arg);
+ bool (*zcal_done) (void *arg);
+ bool (*tmds_valid) (void *arg);
+};
+
+/**
+ * struct dw_phy_pdata - Platform data definition for Synopsys HDMI PHY.
+ *
+ * @funcs: set of callbacks that must be correctly filled and supplied to phy.
+ * See @dw_phy_funcs.
+ *
+ * @funcs_arg: parameter that is supplied to callbacks along with the function
+ * parameters.
+ */
+struct dw_phy_pdata {
+ const struct dw_phy_funcs *funcs;
+ void *funcs_arg;
+};
+
+#endif /* __DW_HDMI_PHY_PDATA_H__ */
--
1.9.1
Document the bindings for the Synopsys Designware HDMI RX.
Signed-off-by: Jose Abreu <[email protected]>
Cc: Carlos Palminha <[email protected]>
Cc: Rob Herring <[email protected]>
Cc: Mark Rutland <[email protected]>
Cc: Mauro Carvalho Chehab <[email protected]>
Cc: Hans Verkuil <[email protected]>
Cc: Sylwester Nawrocki <[email protected]>
Changes from v3:
- Document the new DT bindings suggested by Sylwester
Changes from v2:
- Document edid-phandle property
---
.../devicetree/bindings/media/snps,dw-hdmi-rx.txt | 70 ++++++++++++++++++++++
1 file changed, 70 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/snps,dw-hdmi-rx.txt
diff --git a/Documentation/devicetree/bindings/media/snps,dw-hdmi-rx.txt b/Documentation/devicetree/bindings/media/snps,dw-hdmi-rx.txt
new file mode 100644
index 0000000..efb0ac3
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/snps,dw-hdmi-rx.txt
@@ -0,0 +1,70 @@
+Synopsys DesignWare HDMI RX Decoder
+===================================
+
+This document defines device tree properties for the Synopsys DesignWare HDMI
+RX Decoder (DWC HDMI RX). It doesn't constitute a device tree binding
+specification by itself but is meant to be referenced by platform-specific
+device tree bindings.
+
+When referenced from platform device tree bindings the properties defined in
+this document are defined as follows.
+
+- compatible: Shall be "snps,dw-hdmi-rx".
+
+- reg: Memory mapped base address and length of the DWC HDMI RX registers.
+
+- interrupts: Reference to the DWC HDMI RX interrupt and 5v sense interrupt.
+
+- clocks: Phandle to the config clock block.
+
+- clock-names: Shall be "cfg-clk".
+
+- edid-phandle: phandle to the EDID handler block.
+
+- #address-cells: Shall be 1.
+
+- #size-cells: Shall be 0.
+
+You also have to create a subnode for phy driver. Phy properties are as follows.
+
+- compatible: Shall be "snps,dw-hdmi-phy-e405".
+
+- reg: Shall be JTAG address of phy.
+
+- clocks: Phandle for cfg clock.
+
+- clock-names:Shall be "cfg-clk".
+
+A sample binding is now provided. The compatible string is for a SoC which has
+has a Synopsys Designware HDMI RX decoder inside.
+
+Example:
+
+dw_hdmi_soc: dw-hdmi-soc@0 {
+ compatible = "snps,dw-hdmi-soc";
+ reg = <0x11c00 0x1000>; /* EDIDs */
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ dw_hdmi_rx@0 {
+ compatible = "snps,dw-hdmi-rx";
+ reg = <0x0 0x10000>;
+ interrupts = <1 2>;
+ edid-phandle = <&dw_hdmi_soc>;
+
+ clocks = <&dw_hdmi_refclk>;
+ clock-names = "cfg-clk";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ dw_hdmi_phy_e405@fc {
+ compatible = "snps,dw-hdmi-phy-e405";
+ reg = <0xfc>;
+
+ clocks = <&dw_hdmi_refclk>;
+ clock-names = "cfg-clk";
+ };
+ };
+};
--
1.9.1
Add a entry for Synopsys Designware HDMI Receivers drivers
and phys.
Signed-off-by: Jose Abreu <[email protected]>
Cc: Carlos Palminha <[email protected]>
---
MAINTAINERS | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index c4be6d4..7ebc6dd 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -11354,6 +11354,13 @@ L: [email protected]
S: Supported
F: drivers/net/ethernet/synopsys/
+SYNOPSYS DESIGNWARE HDMI RECEIVERS AND PHY DRIVERS
+M: Jose Abreu <[email protected]>
+L: [email protected]
+S: Maintained
+F: drivers/media/platform/dwc/*
+F: include/media/dwc/*
+
SYNOPSYS DESIGNWARE I2C DRIVER
M: Jarkko Nikula <[email protected]>
R: Andy Shevchenko <[email protected]>
--
1.9.1
This is an initial submission for the Synopsys Designware HDMI RX
Controller Driver. This driver interacts with a phy driver so that
a communication between them is created and a video pipeline is
configured.
The controller + phy pipeline can then be integrated into a fully
featured system that can be able to receive video up to 4k@60Hz
with deep color 48bit RGB, depending on the platform. Although,
this initial version does not yet handle deep color modes.
This driver was implemented as a standard V4L2 subdevice and its
main features are:
- Internal state machine that reconfigures phy until the
video is not stable
- JTAG communication with phy
- Inter-module communication with phy driver
- Debug write/read ioctls
Some notes:
- RX sense controller (cable connection/disconnection) must
be handled by the platform wrapper as this is not integrated
into the controller RTL
- The same goes for EDID ROM's
- ZCAL calibration is needed only in FPGA platforms, in ASIC
this is not needed
- The state machine is not an ideal solution as it creates a
kthread but it is needed because some sources might not be
very stable at sending the video (i.e. we must react
accordingly).
Signed-off-by: Jose Abreu <[email protected]>
Cc: Carlos Palminha <[email protected]>
Cc: Mauro Carvalho Chehab <[email protected]>
Cc: Hans Verkuil <[email protected]>
Cc: Sylwester Nawrocki <[email protected]>
Changes from v3:
- Use v4l2 async API (Sylwester)
- Do not block waiting for phy
- Do not use busy waiting delays (Sylwester)
- Simplify dw_hdmi_power_on (Sylwester)
- Use clock API (Sylwester)
- Use compatible string (Sylwester)
- Minor fixes (Sylwester)
Changes from v2:
- Address review comments from Hans regarding CEC
- Use CEC notifier
- Enable SCDC
Changes from v1:
- Add support for CEC
- Correct typo errors
- Correctly detect interlaced video modes
- Correct VIC parsing
Changes from RFC:
- Add support for HDCP 1.4
- Fixup HDMI_VIC not being parsed (Hans)
- Send source change signal when powering off (Hans)
- Add a "wait stable delay"
- Detect interlaced video modes (Hans)
- Restrain g/s_register from reading/writing to HDCP regs (Hans)
---
drivers/media/platform/dwc/Kconfig | 15 +
drivers/media/platform/dwc/Makefile | 1 +
drivers/media/platform/dwc/dw-hdmi-rx.c | 1862 +++++++++++++++++++++++++++++++
drivers/media/platform/dwc/dw-hdmi-rx.h | 441 ++++++++
include/media/dwc/dw-hdmi-rx-pdata.h | 97 ++
5 files changed, 2416 insertions(+)
create mode 100644 drivers/media/platform/dwc/dw-hdmi-rx.c
create mode 100644 drivers/media/platform/dwc/dw-hdmi-rx.h
create mode 100644 include/media/dwc/dw-hdmi-rx-pdata.h
diff --git a/drivers/media/platform/dwc/Kconfig b/drivers/media/platform/dwc/Kconfig
index 361d38d..3ddccde 100644
--- a/drivers/media/platform/dwc/Kconfig
+++ b/drivers/media/platform/dwc/Kconfig
@@ -6,3 +6,18 @@ config VIDEO_DWC_HDMI_PHY_E405
To compile this driver as a module, choose M here. The module
will be called dw-hdmi-phy-e405.
+
+config VIDEO_DWC_HDMI_RX
+ tristate "Synopsys Designware HDMI Receiver driver"
+ depends on VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API
+ help
+ Support for Synopsys Designware HDMI RX controller.
+
+ To compile this driver as a module, choose M here. The module
+ will be called dw-hdmi-rx.
+
+config VIDEO_DWC_HDMI_RX_CEC
+ bool
+ depends on VIDEO_DWC_HDMI_RX
+ select CEC_CORE
+ select CEC_NOTIFIER
diff --git a/drivers/media/platform/dwc/Makefile b/drivers/media/platform/dwc/Makefile
index fc3b62c..cd04ca9 100644
--- a/drivers/media/platform/dwc/Makefile
+++ b/drivers/media/platform/dwc/Makefile
@@ -1 +1,2 @@
obj-$(CONFIG_VIDEO_DWC_HDMI_PHY_E405) += dw-hdmi-phy-e405.o
+obj-$(CONFIG_VIDEO_DWC_HDMI_RX) += dw-hdmi-rx.o
diff --git a/drivers/media/platform/dwc/dw-hdmi-rx.c b/drivers/media/platform/dwc/dw-hdmi-rx.c
new file mode 100644
index 0000000..22ee51d
--- /dev/null
+++ b/drivers/media/platform/dwc/dw-hdmi-rx.c
@@ -0,0 +1,1862 @@
+/*
+ * Synopsys Designware HDMI Receiver controller driver
+ *
+ * This Synopsys dw-hdmi-rx software and associated documentation
+ * (hereinafter the "Software") is an unsupported proprietary work of
+ * Synopsys, Inc. unless otherwise expressly agreed to in writing between
+ * Synopsys and you. The Software IS NOT an item of Licensed Software or a
+ * Licensed Product under any End User Software License Agreement or
+ * Agreement for Licensed Products with Synopsys or any supplement thereto.
+ * Synopsys is a registered trademark of Synopsys, Inc. Other names included
+ * in the SOFTWARE may be the trademarks of their respective owners.
+ *
+ * The contents of this file are dual-licensed; you may select either version 2
+ * of the GNU General Public License (“GPL”) or the MIT license (“MIT”).
+ *
+ * Copyright (c) 2017 Synopsys, Inc. and/or its affiliates.
+ *
+ * THIS SOFTWARE IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING, BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE, AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR
+ * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT, OR OTHERWISE
+ * ARISING FROM, OUT OF, OR IN CONNECTION WITH THE SOFTWARE THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/v4l2-dv-timings.h>
+#include <linux/workqueue.h>
+#include <media/cec.h>
+#include <media/cec-notifier.h>
+#include <media/v4l2-async.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-dv-timings.h>
+#include <media/v4l2-event.h>
+#include <media/v4l2-subdev.h>
+#include <media/dwc/dw-hdmi-phy-pdata.h>
+#include <media/dwc/dw-hdmi-rx-pdata.h>
+#include "dw-hdmi-rx.h"
+
+#define HDMI_DEFAULT_TIMING V4L2_DV_BT_CEA_640X480P59_94
+#define HDMI_CEC_MAX_LOG_ADDRS CEC_MAX_LOG_ADDRS
+
+MODULE_AUTHOR("Carlos Palminha <[email protected]>");
+MODULE_AUTHOR("Jose Abreu <[email protected]>");
+MODULE_DESCRIPTION("Designware HDMI Receiver driver");
+MODULE_LICENSE("Dual MIT/GPL");
+
+static const struct v4l2_dv_timings_cap dw_hdmi_timings_cap = {
+ .type = V4L2_DV_BT_656_1120,
+ .reserved = { 0 },
+ V4L2_INIT_BT_TIMINGS(
+ 640, 4096, /* min/max width */
+ 480, 4455, /* min/max height */
+ 20000000, 600000000, /* min/max pixelclock */
+ V4L2_DV_BT_STD_CEA861, /* standards */
+ /* capabilities */
+ V4L2_DV_BT_CAP_PROGRESSIVE
+ )
+};
+
+static const struct v4l2_event dw_hdmi_event_fmt = {
+ .type = V4L2_EVENT_SOURCE_CHANGE,
+ .u.src_change.changes = V4L2_EVENT_SRC_CH_RESOLUTION,
+};
+
+enum dw_hdmi_state {
+ HDMI_STATE_NO_INIT = 0,
+ HDMI_STATE_POWER_OFF,
+ HDMI_STATE_PHY_CONFIG,
+ HDMI_STATE_EQUALIZER,
+ HDMI_STATE_VIDEO_UNSTABLE,
+ HDMI_STATE_POWER_ON,
+};
+
+struct dw_hdmi_dev {
+ struct v4l2_async_notifier v4l2_notifier;
+ struct v4l2_async_subdev phy_async_sd;
+ struct dw_hdmi_rx_pdata *config;
+ struct workqueue_struct *wq;
+ struct work_struct work;
+ enum dw_hdmi_state state;
+ bool registered;
+ bool pending_config;
+ bool force_off;
+ spinlock_t lock;
+ void __iomem *regs;
+ struct device_node *of_node;
+ struct v4l2_subdev sd;
+ struct v4l2_dv_timings timings;
+ struct v4l2_device v4l2_dev;
+ struct dw_phy_pdata phy_config;
+ struct platform_device *notifier_pdev;
+ struct v4l2_subdev *phy_sd;
+ bool phy_eq_force;
+ u8 phy_jtag_addr;
+ const char *phy_drv;
+ struct device *dev;
+ u32 mbus_code;
+ unsigned int selected_input;
+ unsigned int configured_input;
+ struct clk *clk;
+ u32 cfg_clk;
+ struct cec_adapter *cec_adap;
+ struct cec_notifier *cec_notifier;
+ bool cec_enabled_adap;
+};
+
+static const char *get_state_name(enum dw_hdmi_state state)
+{
+ switch (state) {
+ case HDMI_STATE_NO_INIT:
+ return "NO_INIT";
+ case HDMI_STATE_POWER_OFF:
+ return "POWER_OFF";
+ case HDMI_STATE_PHY_CONFIG:
+ return "PHY_CONFIG";
+ case HDMI_STATE_EQUALIZER:
+ return "EQUALIZER";
+ case HDMI_STATE_VIDEO_UNSTABLE:
+ return "VIDEO_UNSTABLE";
+ case HDMI_STATE_POWER_ON:
+ return "POWER_ON";
+ default:
+ return "UNKNOWN";
+ }
+}
+
+static inline void dw_hdmi_set_state(struct dw_hdmi_dev *dw_dev,
+ enum dw_hdmi_state new_state)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&dw_dev->lock, flags);
+ dev_dbg(dw_dev->dev, "old_state=%s, new_state=%s\n",
+ get_state_name(dw_dev->state),
+ get_state_name(new_state));
+ dw_dev->state = new_state;
+ spin_unlock_irqrestore(&dw_dev->lock, flags);
+}
+
+static inline struct dw_hdmi_dev *to_dw_dev(struct v4l2_subdev *sd)
+{
+ return container_of(sd, struct dw_hdmi_dev, sd);
+}
+
+static inline struct dw_hdmi_dev *notifier_to_dw_dev(
+ struct v4l2_async_notifier *notifier)
+{
+ return container_of(notifier, struct dw_hdmi_dev, v4l2_notifier);
+}
+
+static inline void hdmi_writel(struct dw_hdmi_dev *dw_dev, u32 val, int reg)
+{
+ writel(val, dw_dev->regs + reg);
+}
+
+static inline u32 hdmi_readl(struct dw_hdmi_dev *dw_dev, int reg)
+{
+ return readl(dw_dev->regs + reg);
+}
+
+static void hdmi_modl(struct dw_hdmi_dev *dw_dev, u32 data, u32 mask, int reg)
+{
+ u32 val = hdmi_readl(dw_dev, reg) & ~mask;
+
+ val |= data & mask;
+ hdmi_writel(dw_dev, val, reg);
+}
+
+static void hdmi_mask_writel(struct dw_hdmi_dev *dw_dev, u32 data, int reg,
+ u32 shift, u32 mask)
+{
+ hdmi_modl(dw_dev, data << shift, mask, reg);
+}
+
+static u32 hdmi_mask_readl(struct dw_hdmi_dev *dw_dev, int reg, u32 shift,
+ u32 mask)
+{
+ return (hdmi_readl(dw_dev, reg) & mask) >> shift;
+}
+
+static bool dw_hdmi_5v_status(struct dw_hdmi_dev *dw_dev, int input)
+{
+ void __iomem *arg = dw_dev->config->dw_5v_arg;
+
+ if (dw_dev->config->dw_5v_status)
+ return dw_dev->config->dw_5v_status(arg, input);
+ return false;
+}
+
+static void dw_hdmi_5v_clear(struct dw_hdmi_dev *dw_dev)
+{
+ void __iomem *arg = dw_dev->config->dw_5v_arg;
+
+ if (dw_dev->config->dw_5v_clear)
+ dw_dev->config->dw_5v_clear(arg);
+}
+
+static inline bool is_off(struct dw_hdmi_dev *dw_dev)
+{
+ return dw_dev->state <= HDMI_STATE_POWER_OFF;
+}
+
+static bool is_hdcp14_key_write_allowed(struct dw_hdmi_dev *dw_dev)
+{
+ return hdmi_readl(dw_dev, HDMI_HDCP_STS) & HDMI_HDCP_STS_KEY_WR_OK;
+}
+
+static bool has_signal(struct dw_hdmi_dev *dw_dev, unsigned int input)
+{
+ return dw_hdmi_5v_status(dw_dev, input);
+}
+
+#define HDMI_JTAG_TAP_ADDR_CMD 0
+#define HDMI_JTAG_TAP_WRITE_CMD 1
+#define HDMI_JTAG_TAP_READ_CMD 3
+
+static void hdmi_phy_jtag_send_pulse(struct dw_hdmi_dev *dw_dev, u8 tms, u8 tdi)
+{
+ u8 val;
+
+ val = tms ? HDMI_PHY_JTAG_TAP_IN_TMS : 0;
+ val |= tdi ? HDMI_PHY_JTAG_TAP_IN_TDI : 0;
+
+ hdmi_writel(dw_dev, 0, HDMI_PHY_JTAG_TAP_TCLK);
+ hdmi_writel(dw_dev, val, HDMI_PHY_JTAG_TAP_IN);
+ hdmi_writel(dw_dev, 1, HDMI_PHY_JTAG_TAP_TCLK);
+}
+
+static void hdmi_phy_jtag_shift_dr(struct dw_hdmi_dev *dw_dev)
+{
+ hdmi_phy_jtag_send_pulse(dw_dev, 1, 0);
+ hdmi_phy_jtag_send_pulse(dw_dev, 0, 0);
+ hdmi_phy_jtag_send_pulse(dw_dev, 0, 0);
+}
+
+static void hdmi_phy_jtag_shift_ir(struct dw_hdmi_dev *dw_dev)
+{
+ hdmi_phy_jtag_send_pulse(dw_dev, 1, 0);
+ hdmi_phy_jtag_send_pulse(dw_dev, 1, 0);
+ hdmi_phy_jtag_send_pulse(dw_dev, 0, 0);
+ hdmi_phy_jtag_send_pulse(dw_dev, 0, 0);
+}
+
+static u16 hdmi_phy_jtag_send(struct dw_hdmi_dev *dw_dev, u8 cmd, u16 val)
+{
+ u32 in = (cmd << 16) | val;
+ u16 out = 0;
+ int i;
+
+ for (i = 0; i < 16; i++) {
+ hdmi_phy_jtag_send_pulse(dw_dev, 0, in & 0x1);
+ out |= (hdmi_readl(dw_dev, HDMI_PHY_JTAG_TAP_OUT) & 0x1) << i;
+ in >>= 1;
+ }
+
+ hdmi_phy_jtag_send_pulse(dw_dev, 0, in & 0x1);
+ in >>= 1;
+ hdmi_phy_jtag_send_pulse(dw_dev, 1, in & 0x1);
+
+ out |= (hdmi_readl(dw_dev, HDMI_PHY_JTAG_TAP_OUT) & 0x1) << ++i;
+ return out;
+}
+
+static void hdmi_phy_jtag_idle(struct dw_hdmi_dev *dw_dev)
+{
+ hdmi_phy_jtag_send_pulse(dw_dev, 1, 0);
+ hdmi_phy_jtag_send_pulse(dw_dev, 0, 0);
+}
+
+static void hdmi_phy_jtag_init(struct dw_hdmi_dev *dw_dev, u8 addr)
+{
+ int i;
+
+ hdmi_writel(dw_dev, addr, HDMI_PHY_JTAG_ADDR);
+ /* reset */
+ hdmi_writel(dw_dev, 0x10, HDMI_PHY_JTAG_TAP_IN);
+ hdmi_writel(dw_dev, 0x0, HDMI_PHY_JTAG_CONF);
+ hdmi_writel(dw_dev, 0x1, HDMI_PHY_JTAG_CONF);
+ hdmi_phy_jtag_send_pulse(dw_dev, 0, 0);
+ /* soft reset */
+ for (i = 0; i < 5; i++)
+ hdmi_phy_jtag_send_pulse(dw_dev, 1, 0);
+ hdmi_phy_jtag_send_pulse(dw_dev, 0, 0);
+ /* set slave address */
+ hdmi_phy_jtag_shift_ir(dw_dev);
+ for (i = 0; i < 7; i++) {
+ hdmi_phy_jtag_send_pulse(dw_dev, 0, addr & 0x1);
+ addr >>= 1;
+ }
+ hdmi_phy_jtag_send_pulse(dw_dev, 1, addr & 0x1);
+ hdmi_phy_jtag_idle(dw_dev);
+}
+
+static void hdmi_phy_jtag_write(struct dw_hdmi_dev *dw_dev, u16 val, u16 addr)
+{
+ hdmi_phy_jtag_shift_dr(dw_dev);
+ hdmi_phy_jtag_send(dw_dev, HDMI_JTAG_TAP_ADDR_CMD, addr << 8);
+ hdmi_phy_jtag_idle(dw_dev);
+ hdmi_phy_jtag_shift_dr(dw_dev);
+ hdmi_phy_jtag_send(dw_dev, HDMI_JTAG_TAP_WRITE_CMD, val);
+ hdmi_phy_jtag_idle(dw_dev);
+}
+
+static u16 hdmi_phy_jtag_read(struct dw_hdmi_dev *dw_dev, u16 addr)
+{
+ u16 val;
+
+ hdmi_phy_jtag_shift_dr(dw_dev);
+ hdmi_phy_jtag_send(dw_dev, HDMI_JTAG_TAP_ADDR_CMD, addr << 8);
+ hdmi_phy_jtag_idle(dw_dev);
+ hdmi_phy_jtag_shift_dr(dw_dev);
+ val = hdmi_phy_jtag_send(dw_dev, HDMI_JTAG_TAP_READ_CMD, 0xFFFF);
+ hdmi_phy_jtag_idle(dw_dev);
+
+ return val;
+}
+
+static void dw_hdmi_phy_write(void *arg, u16 val, u16 addr)
+{
+ struct dw_hdmi_dev *dw_dev = arg;
+ u16 rval;
+
+ hdmi_phy_jtag_init(dw_dev, dw_dev->phy_jtag_addr);
+ hdmi_phy_jtag_write(dw_dev, val, addr);
+ rval = hdmi_phy_jtag_read(dw_dev, addr);
+
+ if (rval != val) {
+ dev_err(dw_dev->dev,
+ "JTAG read-back failed: expected=0x%x, got=0x%x\n",
+ val, rval);
+ }
+}
+
+static u16 dw_hdmi_phy_read(void *arg, u16 addr)
+{
+ struct dw_hdmi_dev *dw_dev = arg;
+
+ hdmi_phy_jtag_init(dw_dev, dw_dev->phy_jtag_addr);
+ return hdmi_phy_jtag_read(dw_dev, addr);
+}
+
+static void dw_hdmi_phy_reset(void *arg, int enable)
+{
+ struct dw_hdmi_dev *dw_dev = arg;
+
+ hdmi_mask_writel(dw_dev, enable, HDMI_PHY_CTRL,
+ HDMI_PHY_CTRL_RESET_OFFSET,
+ HDMI_PHY_CTRL_RESET_MASK);
+}
+
+static void dw_hdmi_phy_pddq(void *arg, int enable)
+{
+ struct dw_hdmi_dev *dw_dev = arg;
+
+ hdmi_mask_writel(dw_dev, enable, HDMI_PHY_CTRL,
+ HDMI_PHY_CTRL_PDDQ_OFFSET,
+ HDMI_PHY_CTRL_PDDQ_MASK);
+}
+
+static void dw_hdmi_phy_svsmode(void *arg, int enable)
+{
+ struct dw_hdmi_dev *dw_dev = arg;
+
+ hdmi_mask_writel(dw_dev, enable, HDMI_PHY_CTRL,
+ HDMI_PHY_CTRL_SVSRETMODEZ_OFFSET,
+ HDMI_PHY_CTRL_SVSRETMODEZ_MASK);
+}
+
+static void dw_hdmi_zcal_reset(void *arg)
+{
+ struct dw_hdmi_dev *dw_dev = arg;
+
+ if (dw_dev->config->dw_zcal_reset)
+ dw_dev->config->dw_zcal_reset(dw_dev->config->dw_zcal_arg);
+}
+
+static bool dw_hdmi_zcal_done(void *arg)
+{
+ struct dw_hdmi_dev *dw_dev = arg;
+
+ if (dw_dev->config->dw_zcal_done)
+ return dw_dev->config->dw_zcal_done(dw_dev->config->dw_zcal_arg);
+ return true;
+}
+
+static bool dw_hdmi_tmds_valid(void *arg)
+{
+ struct dw_hdmi_dev *dw_dev = arg;
+
+ return hdmi_readl(dw_dev, HDMI_PLL_LCK_STS) & HDMI_PLL_LCK_STS_PLL_LOCKED;
+}
+
+static const struct dw_phy_funcs dw_hdmi_phy_funcs = {
+ .write = dw_hdmi_phy_write,
+ .read = dw_hdmi_phy_read,
+ .reset = dw_hdmi_phy_reset,
+ .pddq = dw_hdmi_phy_pddq,
+ .svsmode = dw_hdmi_phy_svsmode,
+ .zcal_reset = dw_hdmi_zcal_reset,
+ .zcal_done = dw_hdmi_zcal_done,
+ .tmds_valid = dw_hdmi_tmds_valid,
+};
+
+static const struct of_device_id dw_hdmi_supported_phys[] = {
+ { .compatible = "snps,dw-hdmi-phy-e405", .data = DW_PHY_E405_DRVNAME, },
+ { },
+};
+
+static struct device_node *dw_hdmi_get_phy_of_node(struct dw_hdmi_dev *dw_dev,
+ const struct of_device_id **found_id)
+{
+ struct device_node *child = NULL;
+ const struct of_device_id *id;
+
+ for_each_child_of_node(dw_dev->of_node, child) {
+ id = of_match_node(dw_hdmi_supported_phys, child);
+ if (id)
+ break;
+ }
+
+ if (found_id)
+ *found_id = id;
+
+ return child;
+}
+
+static int dw_hdmi_phy_init(struct dw_hdmi_dev *dw_dev)
+{
+ struct dw_phy_pdata *phy = &dw_dev->phy_config;
+ const struct of_device_id *of_id;
+ struct of_dev_auxdata lookup;
+ struct device_node *child;
+ const char *drvname;
+ int ret;
+
+ child = dw_hdmi_get_phy_of_node(dw_dev, &of_id);
+ if (!child || !of_id || !of_id->data) {
+ dev_err(dw_dev->dev, "no supported phy found in DT\n");
+ return -EINVAL;
+ }
+
+ drvname = of_id->data;
+ phy->funcs = &dw_hdmi_phy_funcs;
+ phy->funcs_arg = dw_dev;
+
+ lookup.compatible = (char *)of_id->compatible;
+ lookup.phys_addr = 0x0;
+ lookup.name = NULL;
+ lookup.platform_data = phy;
+
+ request_module(drvname);
+
+ ret = of_platform_populate(dw_dev->of_node, NULL, &lookup, dw_dev->dev);
+ if (ret) {
+ dev_err(dw_dev->dev, "failed to populate phy driver\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+static void dw_hdmi_phy_exit(struct dw_hdmi_dev *dw_dev)
+{
+ of_platform_depopulate(dw_dev->dev);
+}
+
+static int dw_hdmi_phy_eq_init(struct dw_hdmi_dev *dw_dev, u16 acq, bool force)
+{
+ struct dw_phy_eq_command cmd = {
+ .result = 0,
+ .nacq = acq,
+ .force = force,
+ };
+ int ret;
+
+ ret = v4l2_subdev_call(dw_dev->phy_sd, core, ioctl,
+ DW_PHY_IOCTL_EQ_INIT, &cmd);
+ if (ret)
+ return ret;
+ return cmd.result;
+}
+
+static int dw_hdmi_phy_config(struct dw_hdmi_dev *dw_dev,
+ unsigned char color_depth, bool hdmi2, bool scrambling)
+{
+ struct dw_phy_config_command cmd = {
+ .result = 0,
+ .color_depth = color_depth,
+ .hdmi2 = hdmi2,
+ .scrambling = scrambling,
+ };
+ int ret;
+
+ hdmi_mask_writel(dw_dev, 0x1, HDMI_CBUSIOCTRL,
+ HDMI_CBUSIOCTRL_DATAPATH_CBUSZ_OFFSET,
+ HDMI_CBUSIOCTRL_DATAPATH_CBUSZ_MASK);
+ hdmi_mask_writel(dw_dev, 0x1, HDMI_CBUSIOCTRL,
+ HDMI_CBUSIOCTRL_SVSRETMODEZ_OFFSET,
+ HDMI_CBUSIOCTRL_SVSRETMODEZ_MASK);
+ hdmi_mask_writel(dw_dev, 0x1, HDMI_CBUSIOCTRL,
+ HDMI_CBUSIOCTRL_PDDQ_OFFSET,
+ HDMI_CBUSIOCTRL_PDDQ_MASK);
+ hdmi_mask_writel(dw_dev, 0x1, HDMI_CBUSIOCTRL,
+ HDMI_CBUSIOCTRL_RESET_OFFSET,
+ HDMI_CBUSIOCTRL_RESET_MASK);
+
+ ret = v4l2_subdev_call(dw_dev->phy_sd, core, ioctl,
+ DW_PHY_IOCTL_CONFIG, &cmd);
+ if (ret)
+ return ret;
+ return cmd.result;
+}
+
+static void dw_hdmi_phy_s_power(struct dw_hdmi_dev *dw_dev, bool on)
+{
+ v4l2_subdev_call(dw_dev->phy_sd, core, s_power, on);
+}
+
+static void dw_hdmi_event_source_change(struct dw_hdmi_dev *dw_dev)
+{
+ if (dw_dev->registered)
+ v4l2_subdev_notify_event(&dw_dev->sd, &dw_hdmi_event_fmt);
+}
+
+static int dw_hdmi_wait_phy_lock_poll(struct dw_hdmi_dev *dw_dev)
+{
+ int timeout = 10;
+
+ while (!dw_hdmi_tmds_valid(dw_dev) && timeout-- && !dw_dev->force_off)
+ usleep_range(5000, 10000);
+
+ if (!dw_hdmi_tmds_valid(dw_dev))
+ return -ETIMEDOUT;
+ return 0;
+}
+
+static void dw_hdmi_reset_datapath(struct dw_hdmi_dev *dw_dev)
+{
+ u32 val = HDMI_DMI_SW_RST_TMDS |
+ HDMI_DMI_SW_RST_HDCP |
+ HDMI_DMI_SW_RST_VID |
+ HDMI_DMI_SW_RST_PIXEL |
+ HDMI_DMI_SW_RST_CEC |
+ HDMI_DMI_SW_RST_AUD |
+ HDMI_DMI_SW_RST_BUS |
+ HDMI_DMI_SW_RST_HDMI |
+ HDMI_DMI_SW_RST_MODET;
+
+ hdmi_writel(dw_dev, val, HDMI_DMI_SW_RST);
+}
+
+static void dw_hdmi_wait_video_stable(struct dw_hdmi_dev *dw_dev)
+{
+ /*
+ * Empiric value. Video should be stable way longer before the
+ * end of this sleep time. Though, we can have some video change
+ * interrupts before the video is stable so filter them by sleeping.
+ */
+ msleep(200);
+}
+
+static void dw_hdmi_enable_ints(struct dw_hdmi_dev *dw_dev)
+{
+ hdmi_writel(dw_dev, HDMI_ISTS_CLK_CHANGE | HDMI_ISTS_PLL_LCK_CHG,
+ HDMI_IEN_SET);
+ hdmi_writel(dw_dev, (~0x0) & (~HDMI_MD_ISTS_VOFS_LIN), HDMI_MD_IEN_SET);
+}
+
+static void dw_hdmi_disable_ints(struct dw_hdmi_dev *dw_dev)
+{
+ hdmi_writel(dw_dev, ~0x0, HDMI_IEN_CLR);
+ hdmi_writel(dw_dev, ~0x0, HDMI_MD_IEN_CLR);
+}
+
+static void dw_hdmi_clear_ints(struct dw_hdmi_dev *dw_dev)
+{
+ hdmi_writel(dw_dev, ~0x0, HDMI_ICLR);
+ hdmi_writel(dw_dev, ~0x0, HDMI_MD_ICLR);
+}
+
+static u32 dw_hdmi_get_int_val(struct dw_hdmi_dev *dw_dev, u32 ists, u32 ien)
+{
+ return hdmi_readl(dw_dev, ists) & hdmi_readl(dw_dev, ien);
+}
+
+#if IS_ENABLED(CONFIG_VIDEO_DWC_HDMI_RX_CEC)
+static void dw_hdmi_cec_enable_ints(struct dw_hdmi_dev *dw_dev)
+{
+ u32 mask = HDMI_AUD_CEC_ISTS_DONE | HDMI_AUD_CEC_ISTS_EOM |
+ HDMI_AUD_CEC_ISTS_NACK | HDMI_AUD_CEC_ISTS_ARBLST |
+ HDMI_AUD_CEC_ISTS_ERROR_INIT | HDMI_AUD_CEC_ISTS_ERROR_FOLL;
+
+ hdmi_writel(dw_dev, mask, HDMI_AUD_CEC_IEN_SET);
+ hdmi_writel(dw_dev, 0x0, HDMI_CEC_MASK);
+}
+
+static void dw_hdmi_cec_disable_ints(struct dw_hdmi_dev *dw_dev)
+{
+ hdmi_writel(dw_dev, ~0x0, HDMI_AUD_CEC_IEN_CLR);
+ hdmi_writel(dw_dev, ~0x0, HDMI_CEC_MASK);
+}
+
+static void dw_hdmi_cec_clear_ints(struct dw_hdmi_dev *dw_dev)
+{
+ hdmi_writel(dw_dev, ~0x0, HDMI_AUD_CEC_ICLR);
+}
+
+static void dw_hdmi_cec_tx_raw_status(struct dw_hdmi_dev *dw_dev, u32 stat)
+{
+ if (hdmi_readl(dw_dev, HDMI_CEC_CTRL) & HDMI_CEC_CTRL_SEND_MASK) {
+ dev_dbg(dw_dev->dev, "%s: tx is busy\n", __func__);
+ return;
+ }
+
+ if (stat & HDMI_AUD_CEC_ISTS_ARBLST) {
+ dev_dbg(dw_dev->dev, "%s: arbitration lost\n", __func__);
+ cec_transmit_done(dw_dev->cec_adap, CEC_TX_STATUS_ARB_LOST,
+ 1, 0, 0, 0);
+ return;
+ }
+
+ if (stat & HDMI_AUD_CEC_ISTS_DONE) {
+ dev_dbg(dw_dev->dev, "%s: transmission done\n", __func__);
+ cec_transmit_done(dw_dev->cec_adap, CEC_TX_STATUS_OK, 0, 0, 0, 0);
+ return;
+ }
+
+ if (stat & HDMI_AUD_CEC_ISTS_NACK) {
+ dev_dbg(dw_dev->dev, "%s: got NACK\n", __func__);
+ cec_transmit_done(dw_dev->cec_adap, CEC_TX_STATUS_NACK,
+ 0, 1, 0, 0);
+ return;
+ }
+
+ if (stat & HDMI_AUD_CEC_ISTS_ERROR_INIT) {
+ dev_dbg(dw_dev->dev, "%s: got initiator error\n", __func__);
+ cec_transmit_done(dw_dev->cec_adap, CEC_TX_STATUS_ERROR,
+ 0, 0, 0, 1);
+ return;
+ }
+}
+
+static void dw_hdmi_cec_received_msg(struct dw_hdmi_dev *dw_dev)
+{
+ struct cec_msg msg;
+ u8 i;
+
+ msg.len = hdmi_readl(dw_dev, HDMI_CEC_RX_CNT);
+ if (!msg.len || msg.len > HDMI_CEC_RX_DATA_MAX)
+ return; /* it's an invalid/non-existent message */
+
+ for (i = 0; i < msg.len; i++)
+ msg.msg[i] = hdmi_readl(dw_dev, HDMI_CEC_RX_DATA(i));
+
+ hdmi_writel(dw_dev, 0x0, HDMI_CEC_LOCK);
+ cec_received_msg(dw_dev->cec_adap, &msg);
+}
+
+static int dw_hdmi_cec_adap_enable(struct cec_adapter *adap, bool enable)
+{
+ struct dw_hdmi_dev *dw_dev = cec_get_drvdata(adap);
+
+ if (!dw_dev->cec_enabled_adap && enable) {
+ hdmi_writel(dw_dev, 0x0, HDMI_CEC_ADDR_L);
+ hdmi_writel(dw_dev, 0x0, HDMI_CEC_ADDR_H);
+ hdmi_writel(dw_dev, 0x0, HDMI_CEC_LOCK);
+ dw_hdmi_cec_clear_ints(dw_dev);
+ dw_hdmi_cec_enable_ints(dw_dev);
+ } else if (dw_dev->cec_enabled_adap && !enable) {
+ hdmi_writel(dw_dev, 0x0, HDMI_CEC_ADDR_L);
+ hdmi_writel(dw_dev, 0x0, HDMI_CEC_ADDR_H);
+ dw_hdmi_cec_disable_ints(dw_dev);
+ dw_hdmi_cec_clear_ints(dw_dev);
+ }
+
+ dw_dev->cec_enabled_adap = enable;
+ return 0;
+}
+
+static int dw_hdmi_cec_adap_log_addr(struct cec_adapter *adap, u8 addr)
+{
+ struct dw_hdmi_dev *dw_dev = cec_get_drvdata(adap);
+ u32 tmp;
+
+ if (addr == CEC_LOG_ADDR_INVALID) {
+ hdmi_writel(dw_dev, 0x0, HDMI_CEC_ADDR_L);
+ hdmi_writel(dw_dev, 0x0, HDMI_CEC_ADDR_H);
+ return 0;
+ }
+
+ if (addr >= 8) {
+ tmp = hdmi_readl(dw_dev, HDMI_CEC_ADDR_H);
+ tmp |= BIT(addr - 8);
+ hdmi_writel(dw_dev, tmp, HDMI_CEC_ADDR_H);
+ } else {
+ tmp = hdmi_readl(dw_dev, HDMI_CEC_ADDR_L);
+ tmp |= BIT(addr);
+ hdmi_writel(dw_dev, tmp, HDMI_CEC_ADDR_L);
+ }
+
+ return 0;
+}
+
+static int dw_hdmi_cec_adap_transmit(struct cec_adapter *adap, u8 attempts,
+ u32 signal_free_time, struct cec_msg *msg)
+{
+ struct dw_hdmi_dev *dw_dev = cec_get_drvdata(adap);
+ u8 len = msg->len;
+ u32 reg;
+ int i;
+
+ if (hdmi_readl(dw_dev, HDMI_CEC_CTRL) & HDMI_CEC_CTRL_SEND_MASK) {
+ dev_err(dw_dev->dev, "%s: tx is busy\n", __func__);
+ return -EBUSY;
+ }
+
+ for (i = 0; i < len; i++)
+ hdmi_writel(dw_dev, msg->msg[i], HDMI_CEC_TX_DATA(i));
+
+ switch (signal_free_time) {
+ case CEC_SIGNAL_FREE_TIME_RETRY:
+ reg = 0x0;
+ break;
+ case CEC_SIGNAL_FREE_TIME_NEXT_XFER:
+ reg = 0x2;
+ break;
+ case CEC_SIGNAL_FREE_TIME_NEW_INITIATOR:
+ default:
+ reg = 0x1;
+ break;
+ }
+
+ hdmi_writel(dw_dev, len, HDMI_CEC_TX_CNT);
+ hdmi_mask_writel(dw_dev, reg, HDMI_CEC_CTRL,
+ HDMI_CEC_CTRL_FRAME_TYP_OFFSET,
+ HDMI_CEC_CTRL_FRAME_TYP_MASK);
+ hdmi_mask_writel(dw_dev, 0x1, HDMI_CEC_CTRL,
+ HDMI_CEC_CTRL_SEND_OFFSET,
+ HDMI_CEC_CTRL_SEND_MASK);
+ return 0;
+}
+
+static const struct cec_adap_ops dw_hdmi_cec_adap_ops = {
+ .adap_enable = dw_hdmi_cec_adap_enable,
+ .adap_log_addr = dw_hdmi_cec_adap_log_addr,
+ .adap_transmit = dw_hdmi_cec_adap_transmit,
+};
+
+static void dw_hdmi_cec_irq_handler(struct dw_hdmi_dev *dw_dev)
+{
+ u32 cec_ists = dw_hdmi_get_int_val(dw_dev, HDMI_AUD_CEC_ISTS,
+ HDMI_AUD_CEC_IEN);
+
+ dw_hdmi_cec_clear_ints(dw_dev);
+
+ if (cec_ists) {
+ dw_hdmi_cec_tx_raw_status(dw_dev, cec_ists);
+ if (cec_ists & HDMI_AUD_CEC_ISTS_EOM)
+ dw_hdmi_cec_received_msg(dw_dev);
+ }
+}
+#endif
+
+static u8 dw_hdmi_get_curr_vic(struct dw_hdmi_dev *dw_dev, bool *is_hdmi_vic)
+{
+ u8 vic = hdmi_mask_readl(dw_dev, HDMI_PDEC_AVI_PB,
+ HDMI_PDEC_AVI_PB_VID_IDENT_CODE_OFFSET,
+ HDMI_PDEC_AVI_PB_VID_IDENT_CODE_MASK) & 0xff;
+
+ if (!vic) {
+ vic = hdmi_mask_readl(dw_dev, HDMI_PDEC_VSI_PAYLOAD0,
+ HDMI_PDEC_VSI_PAYLOAD0_HDMI_VIC_OFFSET,
+ HDMI_PDEC_VSI_PAYLOAD0_HDMI_VIC_MASK) & 0xff;
+ if (is_hdmi_vic)
+ *is_hdmi_vic = true;
+ } else {
+ if (is_hdmi_vic)
+ *is_hdmi_vic = false;
+ }
+
+ return vic;
+}
+
+static u64 dw_hdmi_get_pixelclk(struct dw_hdmi_dev *dw_dev)
+{
+ u32 rate = hdmi_mask_readl(dw_dev, HDMI_CKM_RESULT,
+ HDMI_CKM_RESULT_CLKRATE_OFFSET,
+ HDMI_CKM_RESULT_CLKRATE_MASK);
+ u32 evaltime = hdmi_mask_readl(dw_dev, HDMI_CKM_EVLTM,
+ HDMI_CKM_EVLTM_EVAL_TIME_OFFSET,
+ HDMI_CKM_EVLTM_EVAL_TIME_MASK);
+ u64 tmp = (u64)rate * (u64)dw_dev->cfg_clk * 1000000;
+
+ do_div(tmp, evaltime);
+ return tmp;
+}
+
+static u32 dw_hdmi_get_colordepth(struct dw_hdmi_dev *dw_dev)
+{
+ u32 dcm = hdmi_mask_readl(dw_dev, HDMI_STS,
+ HDMI_STS_DCM_CURRENT_MODE_OFFSET,
+ HDMI_STS_DCM_CURRENT_MODE_MASK);
+
+ switch (dcm) {
+ case 0x4:
+ return 24;
+ case 0x5:
+ return 30;
+ case 0x6:
+ return 36;
+ case 0x7:
+ return 48;
+ default:
+ return 24;
+ }
+}
+
+static void dw_hdmi_set_input(struct dw_hdmi_dev *dw_dev, u32 input)
+{
+ hdmi_mask_writel(dw_dev, input, HDMI_PHY_CTRL,
+ HDMI_PHY_CTRL_PORTSELECT_OFFSET,
+ HDMI_PHY_CTRL_PORTSELECT_MASK);
+}
+
+static void dw_hdmi_enable_hpd(struct dw_hdmi_dev *dw_dev, u32 input_mask)
+{
+ hdmi_mask_writel(dw_dev, input_mask, HDMI_SETUP_CTRL,
+ HDMI_SETUP_CTRL_HOT_PLUG_DETECT_INPUT_X_OFFSET,
+ HDMI_SETUP_CTRL_HOT_PLUG_DETECT_INPUT_X_MASK);
+ hdmi_mask_writel(dw_dev, 0x1, HDMI_SETUP_CTRL,
+ HDMI_SETUP_CTRL_HOT_PLUG_DETECT_OFFSET,
+ HDMI_SETUP_CTRL_HOT_PLUG_DETECT_MASK);
+}
+
+static void dw_hdmi_disable_hpd(struct dw_hdmi_dev *dw_dev)
+{
+ hdmi_mask_writel(dw_dev, 0x0, HDMI_SETUP_CTRL,
+ HDMI_SETUP_CTRL_HOT_PLUG_DETECT_INPUT_X_OFFSET,
+ HDMI_SETUP_CTRL_HOT_PLUG_DETECT_INPUT_X_MASK);
+ hdmi_mask_writel(dw_dev, 0x0, HDMI_SETUP_CTRL,
+ HDMI_SETUP_CTRL_HOT_PLUG_DETECT_OFFSET,
+ HDMI_SETUP_CTRL_HOT_PLUG_DETECT_MASK);
+}
+
+static void dw_hdmi_enable_scdc(struct dw_hdmi_dev *dw_dev)
+{
+ hdmi_mask_writel(dw_dev, 0x1, HDMI_SCDC_CONFIG,
+ HDMI_SCDC_CONFIG_POWERPROVIDED_OFFSET,
+ HDMI_SCDC_CONFIG_POWERPROVIDED_MASK);
+}
+
+static void dw_hdmi_disable_scdc(struct dw_hdmi_dev *dw_dev)
+{
+ hdmi_mask_writel(dw_dev, 0x0, HDMI_SCDC_CONFIG,
+ HDMI_SCDC_CONFIG_POWERPROVIDED_OFFSET,
+ HDMI_SCDC_CONFIG_POWERPROVIDED_MASK);
+}
+
+static int dw_hdmi_config(struct dw_hdmi_dev *dw_dev, u32 input)
+{
+ int eqret, ret = 0;
+
+ while (1) {
+ /* Give up silently if we are forcing off */
+ if (dw_dev->force_off) {
+ ret = 0;
+ goto out;
+ }
+ /* Give up silently if input has disconnected */
+ if (!has_signal(dw_dev, input)) {
+ ret = 0;
+ goto out;
+ }
+
+ switch (dw_dev->state) {
+ case HDMI_STATE_POWER_OFF:
+ dw_hdmi_disable_ints(dw_dev);
+ dw_hdmi_set_state(dw_dev, HDMI_STATE_PHY_CONFIG);
+ break;
+ case HDMI_STATE_PHY_CONFIG:
+ dw_hdmi_phy_s_power(dw_dev, true);
+ dw_hdmi_phy_config(dw_dev, 8, false, false);
+ dw_hdmi_set_state(dw_dev, HDMI_STATE_EQUALIZER);
+ break;
+ case HDMI_STATE_EQUALIZER:
+ eqret = dw_hdmi_phy_eq_init(dw_dev, 5,
+ dw_dev->phy_eq_force);
+ ret = dw_hdmi_wait_phy_lock_poll(dw_dev);
+
+ /* Do not force equalizer */
+ dw_dev->phy_eq_force = false;
+
+ if (ret || eqret) {
+ if (ret || eqret == -ETIMEDOUT) {
+ /* No TMDSVALID signal:
+ * - force equalizer */
+ dw_dev->phy_eq_force = true;
+ }
+ break;
+ }
+
+ dw_hdmi_set_state(dw_dev, HDMI_STATE_VIDEO_UNSTABLE);
+ break;
+ case HDMI_STATE_VIDEO_UNSTABLE:
+ dw_hdmi_reset_datapath(dw_dev);
+ dw_hdmi_wait_video_stable(dw_dev);
+ dw_hdmi_clear_ints(dw_dev);
+ dw_hdmi_enable_ints(dw_dev);
+ dw_hdmi_set_state(dw_dev, HDMI_STATE_POWER_ON);
+ break;
+ case HDMI_STATE_POWER_ON:
+ break;
+ default:
+ dev_err(dw_dev->dev, "%s called with state (%d)\n",
+ __func__, dw_dev->state);
+ ret = -EINVAL;
+ goto out;
+ }
+
+ if (dw_dev->state == HDMI_STATE_POWER_ON) {
+ dev_info(dw_dev->dev, "HDMI-RX configured\n");
+ dw_hdmi_event_source_change(dw_dev);
+ return 0;
+ }
+ }
+
+out:
+ dw_hdmi_set_state(dw_dev, HDMI_STATE_POWER_OFF);
+ return ret;
+}
+
+static int dw_hdmi_config_hdcp(struct dw_hdmi_dev *dw_dev)
+{
+ struct dw_hdmi_hdcp14_key *keys = &dw_dev->config->hdcp14_keys;
+ int i, j, key_write_tries = 5;
+
+ /* TODO: HDCP 2.2 is not implemented in SW for now, just bypass it */
+ hdmi_mask_writel(dw_dev, 0x0, HDMI_HDCP22_CONTROL,
+ HDMI_HDCP22_CONTROL_OVR_VAL_OFFSET,
+ HDMI_HDCP22_CONTROL_OVR_VAL_MASK);
+ hdmi_mask_writel(dw_dev, 0x1, HDMI_HDCP22_CONTROL,
+ HDMI_HDCP22_CONTROL_OVR_EN_OFFSET,
+ HDMI_HDCP22_CONTROL_OVR_EN_MASK);
+
+ if (!keys->keys_valid) {
+ dev_warn(dw_dev->dev, "[HDCP 1.4] no valid keys provided\n");
+ return 0;
+ }
+
+ hdmi_mask_writel(dw_dev, 0x0, HDMI_HDCP_CTRL,
+ HDMI_HDCP_CTRL_ENABLE_OFFSET,
+ HDMI_HDCP_CTRL_ENABLE_MASK);
+ hdmi_mask_writel(dw_dev, 0x1, HDMI_HDCP_CTRL,
+ HDMI_HDCP_CTRL_KEY_DECRYPT_ENABLE_OFFSET,
+ HDMI_HDCP_CTRL_KEY_DECRYPT_ENABLE_MASK);
+
+ hdmi_writel(dw_dev, keys->seed, HDMI_HDCP_SEED);
+
+ for (i = 0; i < DW_HDMI_HDCP14_KEYS_SIZE; i += 2) {
+ for (j = 0; j < key_write_tries; j++) {
+ if (is_hdcp14_key_write_allowed(dw_dev))
+ break;
+ usleep_range(5000, 10000);
+ }
+
+ if (j == key_write_tries)
+ return -ETIMEDOUT;
+
+ hdmi_writel(dw_dev, keys->keys[i], HDMI_HDCP_KEY1);
+ hdmi_writel(dw_dev, keys->keys[i + 1], HDMI_HDCP_KEY0);
+ }
+
+ hdmi_writel(dw_dev, keys->bksv[0], HDMI_HDCP_BKSV1);
+ hdmi_writel(dw_dev, keys->bksv[1], HDMI_HDCP_BKSV0);
+
+ hdmi_mask_writel(dw_dev, 0x1, HDMI_HDCP_CTRL,
+ HDMI_HDCP_CTRL_ENABLE_OFFSET,
+ HDMI_HDCP_CTRL_ENABLE_MASK);
+ return 0;
+}
+
+static int __dw_hdmi_power_on(struct dw_hdmi_dev *dw_dev, u32 input)
+{
+ unsigned long flags;
+ int ret;
+
+ ret = dw_hdmi_config(dw_dev, input);
+
+ spin_lock_irqsave(&dw_dev->lock, flags);
+ dw_dev->pending_config = false;
+ spin_unlock_irqrestore(&dw_dev->lock, flags);
+
+ return ret;
+}
+
+static void dw_hdmi_work_handler(struct work_struct *work)
+{
+ struct dw_hdmi_dev *dw_dev = container_of(work, struct dw_hdmi_dev, work);
+
+ __dw_hdmi_power_on(dw_dev, dw_dev->configured_input);
+}
+
+static int dw_hdmi_power_on(struct dw_hdmi_dev *dw_dev, u32 input)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&dw_dev->lock, flags);
+ if (dw_dev->pending_config) {
+ spin_unlock_irqrestore(&dw_dev->lock, flags);
+ return 0;
+ }
+
+ INIT_WORK(&dw_dev->work, dw_hdmi_work_handler);
+ dw_dev->configured_input = input;
+ dw_dev->pending_config = true;
+ queue_work(dw_dev->wq, &dw_dev->work);
+ spin_unlock_irqrestore(&dw_dev->lock, flags);
+ return 0;
+}
+
+static void dw_hdmi_power_off(struct dw_hdmi_dev *dw_dev)
+{
+ unsigned long flags;
+
+ dw_dev->force_off = true;
+ flush_workqueue(dw_dev->wq);
+ dw_dev->force_off = false;
+
+ spin_lock_irqsave(&dw_dev->lock, flags);
+ dw_dev->pending_config = false;
+ dw_dev->state = HDMI_STATE_POWER_OFF;
+ spin_unlock_irqrestore(&dw_dev->lock, flags);
+
+ /* Reset variables */
+ dw_dev->phy_eq_force = true;
+
+ /* Send source change event to userspace */
+ dw_hdmi_event_source_change(dw_dev);
+}
+
+static irqreturn_t dw_hdmi_irq_handler(int irq, void *dev_data)
+{
+ struct dw_hdmi_dev *dw_dev = dev_data;
+ u32 hdmi_ists = dw_hdmi_get_int_val(dw_dev, HDMI_ISTS, HDMI_IEN);
+ u32 md_ists = dw_hdmi_get_int_val(dw_dev, HDMI_MD_ISTS, HDMI_MD_IEN);
+
+ dw_hdmi_clear_ints(dw_dev);
+
+ if ((hdmi_ists & HDMI_ISTS_CLK_CHANGE) ||
+ (hdmi_ists & HDMI_ISTS_PLL_LCK_CHG) || md_ists) {
+ dw_hdmi_power_off(dw_dev);
+ if (has_signal(dw_dev, dw_dev->configured_input))
+ dw_hdmi_power_on(dw_dev, dw_dev->configured_input);
+ }
+
+#if IS_ENABLED(CONFIG_VIDEO_DWC_HDMI_RX_CEC)
+ dw_hdmi_cec_irq_handler(dw_dev);
+#endif
+
+ return IRQ_HANDLED;
+}
+
+static void dw_hdmi_detect_tx_5v(struct dw_hdmi_dev *dw_dev)
+{
+ unsigned int input_count = 4; /* TODO: Get from DT node this value */
+ unsigned int old_input = dw_dev->configured_input;
+ unsigned int new_input = old_input;
+ bool pending_config = false, current_on = true;
+ u32 stat = 0;
+ int i;
+
+ if (!has_signal(dw_dev, old_input)) {
+ dw_hdmi_disable_ints(dw_dev);
+ dw_hdmi_power_off(dw_dev);
+ current_on = false;
+ }
+
+ for (i = 0; i < input_count; i++) {
+ bool on = has_signal(dw_dev, i);
+ stat |= on << i;
+
+ if (is_off(dw_dev) && on && !pending_config) {
+ dw_hdmi_power_on(dw_dev, i);
+ dw_hdmi_set_input(dw_dev, i);
+ new_input = i;
+ pending_config = true;
+ }
+ }
+
+ if ((new_input == old_input) && !pending_config && !current_on)
+ dw_hdmi_phy_s_power(dw_dev, false);
+
+ if (stat) {
+ /*
+ * If there are any connected ports enable the HPD and the SCDC
+ * for these ports.
+ */
+ dw_hdmi_enable_scdc(dw_dev);
+ dw_hdmi_enable_hpd(dw_dev, stat);
+ } else {
+ /*
+ * If there are no connected ports disable whole HPD and SCDC
+ * also.
+ */
+ dw_hdmi_disable_hpd(dw_dev);
+ dw_hdmi_disable_scdc(dw_dev);
+ }
+
+ dev_dbg(dw_dev->dev, "%s: %d%d%d%d\n", __func__,
+ dw_hdmi_5v_status(dw_dev, 0),
+ dw_hdmi_5v_status(dw_dev, 1),
+ dw_hdmi_5v_status(dw_dev, 2),
+ dw_hdmi_5v_status(dw_dev, 3));
+}
+
+static irqreturn_t dw_hdmi_5v_irq_handler(int irq, void *dev_data)
+{
+ struct dw_hdmi_dev *dw_dev = dev_data;
+
+ dw_hdmi_detect_tx_5v(dw_dev);
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t dw_hdmi_5v_hard_irq_handler(int irq, void *dev_data)
+{
+ struct dw_hdmi_dev *dw_dev = dev_data;
+
+ dev_dbg(dw_dev->dev, "%s\n", __func__);
+ dw_hdmi_5v_clear(dw_dev);
+ return IRQ_WAKE_THREAD;
+}
+
+static int dw_hdmi_s_routing(struct v4l2_subdev *sd, u32 input, u32 output,
+ u32 config)
+{
+ struct dw_hdmi_dev *dw_dev = to_dw_dev(sd);
+
+ if (!has_signal(dw_dev, input))
+ return -EINVAL;
+
+ dw_dev->selected_input = input;
+ if (input == dw_dev->configured_input)
+ return 0;
+
+ dw_hdmi_power_off(dw_dev);
+ return dw_hdmi_power_on(dw_dev, input);
+}
+
+static int dw_hdmi_g_input_status(struct v4l2_subdev *sd, u32 *status)
+{
+ struct dw_hdmi_dev *dw_dev = to_dw_dev(sd);
+
+ *status = 0;
+ if (!has_signal(dw_dev, dw_dev->selected_input))
+ *status |= V4L2_IN_ST_NO_POWER;
+ if (is_off(dw_dev))
+ *status |= V4L2_IN_ST_NO_SIGNAL;
+
+ dev_dbg(dw_dev->dev, "%s: status=0x%x\n", __func__, *status);
+ return 0;
+}
+
+static int dw_hdmi_g_parm(struct v4l2_subdev *sd, struct v4l2_streamparm *parm)
+{
+ struct dw_hdmi_dev *dw_dev = to_dw_dev(sd);
+
+ dev_dbg(dw_dev->dev, "%s\n", __func__);
+
+ /* TODO: Use helper to compute timeperframe */
+ parm->parm.capture.timeperframe.numerator = 1;
+ parm->parm.capture.timeperframe.denominator = 60;
+ return 0;
+}
+
+static int dw_hdmi_g_dv_timings(struct v4l2_subdev *sd,
+ struct v4l2_dv_timings *timings)
+{
+ struct dw_hdmi_dev *dw_dev = to_dw_dev(sd);
+
+ dev_dbg(dw_dev->dev, "%s\n", __func__);
+
+ *timings = dw_dev->timings;
+ return 0;
+}
+
+static int dw_hdmi_query_dv_timings(struct v4l2_subdev *sd,
+ struct v4l2_dv_timings *timings)
+{
+ struct dw_hdmi_dev *dw_dev = to_dw_dev(sd);
+ struct v4l2_bt_timings *bt = &timings->bt;
+ bool is_hdmi_vic;
+ u32 htot, hofs;
+ u32 vtot;
+ u8 vic;
+
+ dev_dbg(dw_dev->dev, "%s\n", __func__);
+
+ memset(timings, 0, sizeof(*timings));
+
+ timings->type = V4L2_DV_BT_656_1120;
+ bt->width = hdmi_readl(dw_dev, HDMI_MD_HACT_PX);
+ bt->height = hdmi_readl(dw_dev, HDMI_MD_VAL);
+ bt->interlaced = hdmi_readl(dw_dev, HDMI_MD_STS) & HDMI_MD_STS_ILACE;
+
+ if (hdmi_readl(dw_dev, HDMI_ISTS) & HDMI_ISTS_VS_POL_ADJ)
+ bt->polarities |= V4L2_DV_VSYNC_POS_POL;
+ if (hdmi_readl(dw_dev, HDMI_ISTS) & HDMI_ISTS_HS_POL_ADJ)
+ bt->polarities |= V4L2_DV_HSYNC_POS_POL;
+
+ bt->pixelclock = dw_hdmi_get_pixelclk(dw_dev);
+
+ /* HTOT = HACT + HFRONT + HSYNC + HBACK */
+ htot = hdmi_mask_readl(dw_dev, HDMI_MD_HT1,
+ HDMI_MD_HT1_HTOT_PIX_OFFSET,
+ HDMI_MD_HT1_HTOT_PIX_MASK);
+ /* HOFS = HSYNC + HBACK */
+ hofs = hdmi_mask_readl(dw_dev, HDMI_MD_HT1,
+ HDMI_MD_HT1_HOFS_PIX_OFFSET,
+ HDMI_MD_HT1_HOFS_PIX_MASK);
+
+ bt->hfrontporch = htot - hofs - bt->width;
+ bt->hsync = hdmi_mask_readl(dw_dev, HDMI_MD_HT0,
+ HDMI_MD_HT0_HS_CLK_OFFSET,
+ HDMI_MD_HT0_HS_CLK_MASK);
+ bt->hbackporch = hofs - bt->hsync;
+
+ /* VTOT = VACT + VFRONT + VSYNC + VBACK */
+ vtot = hdmi_readl(dw_dev, HDMI_MD_VTL);
+
+ hdmi_mask_writel(dw_dev, 0x1, HDMI_MD_VCTRL,
+ HDMI_MD_VCTRL_V_OFFS_LIN_MODE_OFFSET,
+ HDMI_MD_VCTRL_V_OFFS_LIN_MODE_MASK);
+ msleep(50);
+ bt->vsync = hdmi_readl(dw_dev, HDMI_MD_VOL);
+
+ hdmi_mask_writel(dw_dev, 0x0, HDMI_MD_VCTRL,
+ HDMI_MD_VCTRL_V_OFFS_LIN_MODE_OFFSET,
+ HDMI_MD_VCTRL_V_OFFS_LIN_MODE_MASK);
+ msleep(50);
+ bt->vbackporch = hdmi_readl(dw_dev, HDMI_MD_VOL);
+ bt->vfrontporch = vtot - bt->height - bt->vsync - bt->vbackporch;
+ bt->standards = V4L2_DV_BT_STD_CEA861;
+
+ vic = dw_hdmi_get_curr_vic(dw_dev, &is_hdmi_vic);
+ if (vic) {
+ if (is_hdmi_vic) {
+ bt->flags |= V4L2_DV_FL_HAS_HDMI_VIC;
+ bt->hdmi_vic = vic;
+ bt->cea861_vic = 0;
+ } else {
+ bt->flags |= V4L2_DV_FL_HAS_CEA861_VIC;
+ bt->hdmi_vic = 0;
+ bt->cea861_vic = vic;
+ }
+ }
+
+ return 0;
+}
+
+static int dw_hdmi_enum_mbus_code(struct v4l2_subdev *sd,
+ struct v4l2_subdev_pad_config *cfg,
+ struct v4l2_subdev_mbus_code_enum *code)
+{
+ struct dw_hdmi_dev *dw_dev = to_dw_dev(sd);
+
+ dev_dbg(dw_dev->dev, "%s\n", __func__);
+ if (code->index != 0)
+ return -EINVAL;
+
+ code->code = dw_dev->mbus_code;
+ return 0;
+}
+
+static int dw_hdmi_fill_format(struct dw_hdmi_dev *dw_dev,
+ struct v4l2_mbus_framefmt *format)
+{
+ memset(format, 0, sizeof(*format));
+
+ format->width = dw_dev->timings.bt.width;
+ format->height = dw_dev->timings.bt.height;
+ format->colorspace = V4L2_COLORSPACE_SRGB;
+ format->code = dw_dev->mbus_code;
+ if (dw_dev->timings.bt.interlaced)
+ format->field = V4L2_FIELD_ALTERNATE;
+ else
+ format->field = V4L2_FIELD_NONE;
+
+ return 0;
+}
+
+static int dw_hdmi_get_fmt(struct v4l2_subdev *sd,
+ struct v4l2_subdev_pad_config *cfg,
+ struct v4l2_subdev_format *format)
+{
+ struct dw_hdmi_dev *dw_dev = to_dw_dev(sd);
+
+ dev_dbg(dw_dev->dev, "%s\n", __func__);
+ return dw_hdmi_fill_format(dw_dev, &format->format);
+}
+
+static int dw_hdmi_set_fmt(struct v4l2_subdev *sd,
+ struct v4l2_subdev_pad_config *cfg,
+ struct v4l2_subdev_format *format)
+{
+ struct dw_hdmi_dev *dw_dev = to_dw_dev(sd);
+
+ dev_dbg(dw_dev->dev, "%s\n", __func__);
+
+ if (format->format.code != dw_dev->mbus_code) {
+ dev_dbg(dw_dev->dev, "invalid format\n");
+ return -EINVAL;
+ }
+
+ return dw_hdmi_get_fmt(sd, cfg, format);
+}
+
+static int dw_hdmi_dv_timings_cap(struct v4l2_subdev *sd,
+ struct v4l2_dv_timings_cap *cap)
+{
+ struct dw_hdmi_dev *dw_dev = to_dw_dev(sd);
+ unsigned int pad = cap->pad;
+
+ dev_dbg(dw_dev->dev, "%s\n", __func__);
+
+ *cap = dw_hdmi_timings_cap;
+ cap->pad = pad;
+ return 0;
+}
+
+static int dw_hdmi_enum_dv_timings(struct v4l2_subdev *sd,
+ struct v4l2_enum_dv_timings *timings)
+{
+ struct dw_hdmi_dev *dw_dev = to_dw_dev(sd);
+
+ dev_dbg(dw_dev->dev, "%s\n", __func__);
+ return v4l2_enum_dv_timings_cap(timings, &dw_hdmi_timings_cap,
+ NULL, NULL);
+}
+
+static int dw_hdmi_log_status(struct v4l2_subdev *sd)
+{
+ struct dw_hdmi_dev *dw_dev = to_dw_dev(sd);
+ struct v4l2_dv_timings timings;
+
+ v4l2_info(sd, "--- Chip configuration ---\n");
+ v4l2_info(sd, "cfg_clk=%dMHz\n", dw_dev->cfg_clk);
+ v4l2_info(sd, "phy_drv=%s, phy_jtag_addr=0x%x\n", dw_dev->phy_drv,
+ dw_dev->phy_jtag_addr);
+
+ v4l2_info(sd, "--- Chip status ---\n");
+ v4l2_info(sd, "selected_input=%d: signal=%d\n", dw_dev->selected_input,
+ has_signal(dw_dev, dw_dev->selected_input));
+ v4l2_info(sd, "configured_input=%d: signal=%d\n",
+ dw_dev->configured_input,
+ has_signal(dw_dev, dw_dev->configured_input));
+
+ v4l2_info(sd, "--- CEC status ---\n");
+ v4l2_info(sd, "enabled=%s\n", dw_dev->cec_enabled_adap ? "yes" : "no");
+
+ v4l2_info(sd, "--- Video status ---\n");
+ v4l2_info(sd, "type=%s, color_depth=%dbits",
+ hdmi_readl(dw_dev, HDMI_PDEC_STS) &
+ HDMI_PDEC_STS_DVIDET ? "dvi" : "hdmi",
+ dw_hdmi_get_colordepth(dw_dev));
+
+ v4l2_info(sd, "--- Video timings ---\n");
+ if (dw_hdmi_query_dv_timings(sd, &timings))
+ v4l2_info(sd, "No video detected\n");
+ else
+ v4l2_print_dv_timings(sd->name, "Detected format: ",
+ &timings, true);
+ v4l2_print_dv_timings(sd->name, "Configured format: ",
+ &dw_dev->timings, true);
+ return 0;
+}
+
+#ifdef CONFIG_VIDEO_ADV_DEBUG
+static void dw_hdmi_invalid_register(struct dw_hdmi_dev *dw_dev, u64 reg)
+{
+ dev_err(dw_dev->dev, "register 0x%llx not supported\n", reg);
+ dev_err(dw_dev->dev, "0x0000-0x7fff: Main controller map\n");
+ dev_err(dw_dev->dev, "0x8000-0x80ff: PHY map\n");
+}
+
+static bool dw_hdmi_is_reserved_register(struct dw_hdmi_dev *dw_dev, u32 reg)
+{
+ if (reg >= HDMI_HDCP_CTRL && reg <= HDMI_HDCP_STS)
+ return true;
+ if (reg == HDMI_HDCP22_CONTROL)
+ return true;
+ if (reg == HDMI_HDCP22_STATUS)
+ return true;
+ return false;
+}
+
+static int dw_hdmi_g_register(struct v4l2_subdev *sd,
+ struct v4l2_dbg_register *reg)
+{
+ struct dw_hdmi_dev *dw_dev = to_dw_dev(sd);
+
+ switch (reg->reg >> 15) {
+ case 0: /* Controller core read */
+ if (dw_hdmi_is_reserved_register(dw_dev, reg->reg & 0x7fff))
+ return -EINVAL;
+
+ reg->size = 4;
+ reg->val = hdmi_readl(dw_dev, reg->reg & 0x7fff);
+ return 0;
+ case 1: /* PHY read */
+ if ((reg->reg & ~0xff) != BIT(15))
+ break;
+
+ reg->size = 2;
+ reg->val = dw_hdmi_phy_read(dw_dev, reg->reg & 0xff);
+ return 0;
+ default:
+ break;
+ }
+
+ dw_hdmi_invalid_register(dw_dev, reg->reg);
+ return 0;
+}
+
+static int dw_hdmi_s_register(struct v4l2_subdev *sd,
+ const struct v4l2_dbg_register *reg)
+{
+ struct dw_hdmi_dev *dw_dev = to_dw_dev(sd);
+
+ switch (reg->reg >> 15) {
+ case 0: /* Controller core write */
+ if (dw_hdmi_is_reserved_register(dw_dev, reg->reg & 0x7fff))
+ return -EINVAL;
+
+ hdmi_writel(dw_dev, reg->val & GENMASK(31,0), reg->reg & 0x7fff);
+ return 0;
+ case 1: /* PHY write */
+ if ((reg->reg & ~0xff) != BIT(15))
+ break;
+ dw_hdmi_phy_write(dw_dev, reg->val & 0xffff, reg->reg & 0xff);
+ return 0;
+ default:
+ break;
+ }
+
+ dw_hdmi_invalid_register(dw_dev, reg->reg);
+ return 0;
+}
+#endif
+
+static int dw_hdmi_subscribe_event(struct v4l2_subdev *sd, struct v4l2_fh *fh,
+ struct v4l2_event_subscription *sub)
+{
+ switch (sub->type) {
+ case V4L2_EVENT_SOURCE_CHANGE:
+ return v4l2_src_change_event_subdev_subscribe(sd, fh, sub);
+ default:
+ return -EINVAL;
+ }
+}
+
+static int dw_hdmi_registered(struct v4l2_subdev *sd)
+{
+ struct dw_hdmi_dev *dw_dev = to_dw_dev(sd);
+ int ret;
+
+ ret = cec_register_adapter(dw_dev->cec_adap, dw_dev->dev);
+ if (ret) {
+ dev_err(dw_dev->dev, "failed to register CEC adapter\n");
+ cec_delete_adapter(dw_dev->cec_adap);
+ return ret;
+ }
+
+ cec_register_cec_notifier(dw_dev->cec_adap, dw_dev->cec_notifier);
+ dw_dev->registered = true;
+ return ret;
+}
+
+static void dw_hdmi_unregistered(struct v4l2_subdev *sd)
+{
+ struct dw_hdmi_dev *dw_dev = to_dw_dev(sd);
+
+ cec_unregister_adapter(dw_dev->cec_adap);
+ cec_notifier_put(dw_dev->cec_notifier);
+}
+
+static const struct v4l2_subdev_core_ops dw_hdmi_sd_core_ops = {
+ .log_status = dw_hdmi_log_status,
+#ifdef CONFIG_VIDEO_ADV_DEBUG
+ .g_register = dw_hdmi_g_register,
+ .s_register = dw_hdmi_s_register,
+#endif
+ .subscribe_event = dw_hdmi_subscribe_event,
+};
+
+static const struct v4l2_subdev_video_ops dw_hdmi_sd_video_ops = {
+ .s_routing = dw_hdmi_s_routing,
+ .g_input_status = dw_hdmi_g_input_status,
+ .g_parm = dw_hdmi_g_parm,
+ .g_dv_timings = dw_hdmi_g_dv_timings,
+ .query_dv_timings = dw_hdmi_query_dv_timings,
+};
+
+static const struct v4l2_subdev_pad_ops dw_hdmi_sd_pad_ops = {
+ .enum_mbus_code = dw_hdmi_enum_mbus_code,
+ .get_fmt = dw_hdmi_get_fmt,
+ .set_fmt = dw_hdmi_set_fmt,
+ .dv_timings_cap = dw_hdmi_dv_timings_cap,
+ .enum_dv_timings = dw_hdmi_enum_dv_timings,
+};
+
+static const struct v4l2_subdev_ops dw_hdmi_sd_ops = {
+ .core = &dw_hdmi_sd_core_ops,
+ .video = &dw_hdmi_sd_video_ops,
+ .pad = &dw_hdmi_sd_pad_ops,
+};
+
+static const struct v4l2_subdev_internal_ops dw_hdmi_internal_ops = {
+ .registered = dw_hdmi_registered,
+ .unregistered = dw_hdmi_unregistered,
+};
+
+static int dw_hdmi_v4l2_notify_bound(struct v4l2_async_notifier *notifier,
+ struct v4l2_subdev *subdev, struct v4l2_async_subdev *asd)
+{
+ struct dw_hdmi_dev *dw_dev = notifier_to_dw_dev(notifier);
+
+ if (dw_dev->phy_async_sd.match.fwnode.fwnode ==
+ of_fwnode_handle(subdev->dev->of_node)) {
+ dev_dbg(dw_dev->dev, "found new subdev '%s'\n", subdev->name);
+ dw_dev->phy_sd = subdev;
+ return 0;
+ }
+
+ return -EINVAL;
+}
+
+static void dw_hdmi_v4l2_notify_unbind(struct v4l2_async_notifier *notifier,
+ struct v4l2_subdev *subdev, struct v4l2_async_subdev *asd)
+{
+ struct dw_hdmi_dev *dw_dev = notifier_to_dw_dev(notifier);
+
+ if (dw_dev->phy_sd == subdev) {
+ dev_dbg(dw_dev->dev, "unbinding '%s'\n", subdev->name);
+ dw_dev->phy_sd = NULL;
+ }
+}
+
+static int dw_hdmi_v4l2_notify_complete(struct v4l2_async_notifier *notifier)
+{
+ struct dw_hdmi_dev *dw_dev = notifier_to_dw_dev(notifier);
+ int ret;
+
+ ret = v4l2_device_register_subdev_nodes(&dw_dev->v4l2_dev);
+ if (ret) {
+ dev_err(dw_dev->dev, "failed to register subdev nodes\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+static int dw_hdmi_v4l2_init_notifier(struct dw_hdmi_dev *dw_dev)
+{
+ struct v4l2_async_subdev **subdevs = NULL;
+ struct device_node *child = NULL;
+
+ subdevs = devm_kzalloc(dw_dev->dev, sizeof(*subdevs), GFP_KERNEL);
+ if (!subdevs)
+ return -ENOMEM;
+
+ child = dw_hdmi_get_phy_of_node(dw_dev, NULL);
+ if (!child)
+ return -EINVAL;
+
+ dw_dev->phy_async_sd.match.fwnode.fwnode = of_fwnode_handle(child);
+ dw_dev->phy_async_sd.match_type = V4L2_ASYNC_MATCH_FWNODE;
+
+ subdevs[0] = &dw_dev->phy_async_sd;
+ dw_dev->v4l2_notifier.num_subdevs = 1;
+ dw_dev->v4l2_notifier.subdevs = subdevs;
+ dw_dev->v4l2_notifier.bound = dw_hdmi_v4l2_notify_bound;
+ dw_dev->v4l2_notifier.unbind = dw_hdmi_v4l2_notify_unbind;
+ dw_dev->v4l2_notifier.complete = dw_hdmi_v4l2_notify_complete;
+
+ return v4l2_async_notifier_register(&dw_dev->v4l2_dev,
+ &dw_dev->v4l2_notifier);
+}
+
+static int dw_hdmi_parse_dt(struct dw_hdmi_dev *dw_dev)
+{
+ struct device_node *notifier, *phy_node, *np = dw_dev->of_node;
+ u32 tmp;
+ int ret;
+
+ if (!np) {
+ dev_err(dw_dev->dev, "missing DT node\n");
+ return -EINVAL;
+ }
+
+ /* PHY properties parsing */
+ phy_node = dw_hdmi_get_phy_of_node(dw_dev, NULL);
+ of_property_read_u32(phy_node, "reg", &tmp);
+
+ dw_dev->phy_jtag_addr = tmp & 0xff;
+ if (!dw_dev->phy_jtag_addr) {
+ dev_err(dw_dev->dev, "missing phy jtag address in DT\n");
+ return -EINVAL;
+ }
+
+ /* Get config clock value */
+ dw_dev->clk = devm_clk_get(dw_dev->dev, "cfg-clk");
+ if (IS_ERR(dw_dev->clk)) {
+ dev_err(dw_dev->dev, "failed to get cfg-clk\n");
+ return PTR_ERR(dw_dev->clk);
+ }
+
+ ret = clk_prepare_enable(dw_dev->clk);
+ if (ret) {
+ dev_err(dw_dev->dev, "failed to enable cfg-clk\n");
+ return ret;
+ }
+
+ dw_dev->cfg_clk = clk_get_rate(dw_dev->clk) / 1000000;
+ if (!dw_dev->cfg_clk) {
+ dev_err(dw_dev->dev, "invalid cfg-clk frequency\n");
+ ret = -EINVAL;
+ goto err_clk;
+ }
+
+#if IS_ENABLED(CONFIG_VIDEO_DWC_HDMI_RX_CEC)
+ /* Notifier device parsing */
+ notifier = of_parse_phandle(np, "edid-phandle", 0);
+ if (!notifier) {
+ dev_err(dw_dev->dev, "missing edid-phandle in DT\n");
+ ret = -EINVAL;
+ goto err_clk;
+ }
+
+ dw_dev->notifier_pdev = of_find_device_by_node(notifier);
+ if (!dw_dev->notifier_pdev)
+ return -EPROBE_DEFER;
+#endif
+
+ return 0;
+
+err_clk:
+ clk_disable_unprepare(dw_dev->clk);
+ return ret;
+}
+
+static int dw_hdmi_rx_probe(struct platform_device *pdev)
+{
+ const struct v4l2_dv_timings timings_def = HDMI_DEFAULT_TIMING;
+ struct dw_hdmi_rx_pdata *pdata = pdev->dev.platform_data;
+ struct device *dev = &pdev->dev;
+ struct dw_hdmi_dev *dw_dev;
+ struct v4l2_subdev *sd;
+ struct resource *res;
+ int ret, irq;
+
+ dev_dbg(dev, "%s\n", __func__);
+
+ /* Resource allocation */
+ dw_dev = devm_kzalloc(dev, sizeof(*dw_dev), GFP_KERNEL);
+ if (!dw_dev)
+ return -ENOMEM;
+
+ /* Resource initialization */
+ if (!pdata) {
+ dev_err(dev, "missing platform data\n");
+ return -EINVAL;
+ }
+
+ dw_dev->dev = dev;
+ dw_dev->config = pdata;
+ dw_dev->state = HDMI_STATE_NO_INIT;
+ dw_dev->of_node = dev->of_node;
+ spin_lock_init(&dw_dev->lock);
+
+ /* Device Tree parsing */
+ ret = dw_hdmi_parse_dt(dw_dev);
+ if (ret)
+ return ret;
+
+ /* Deferred work */
+ dw_dev->wq = create_singlethread_workqueue(DW_HDMI_RX_DRVNAME);
+ if (!dw_dev->wq) {
+ dev_err(dev, "failed to create workqueue\n");
+ return -ENOMEM;
+ }
+
+ /* Registers mapping */
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+
+ dw_dev->regs = devm_ioremap_resource(dev, res);
+ if (IS_ERR(dw_dev->regs)) {
+ dev_err(dev, "failed to remap resource\n");
+ ret = PTR_ERR(dw_dev->regs);
+ goto err_wq;
+ }
+
+ /* Disable HPD as soon as posssible */
+ dw_hdmi_disable_hpd(dw_dev);
+
+ /* Configure HDCP */
+ ret = dw_hdmi_config_hdcp(dw_dev);
+ if (ret)
+ goto err_wq;
+
+ /* Interrupts mapping */
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0) {
+ ret = irq;
+ goto err_wq;
+ }
+
+ ret = devm_request_threaded_irq(dev, irq, NULL, dw_hdmi_irq_handler,
+ IRQF_ONESHOT, DW_HDMI_RX_DRVNAME, dw_dev);
+ if (ret)
+ goto err_wq;
+
+ irq = platform_get_irq(pdev, 1);
+ if (irq < 0) {
+ ret = irq;
+ goto err_wq;
+ }
+
+ ret = devm_request_threaded_irq(dev, irq, dw_hdmi_5v_hard_irq_handler,
+ dw_hdmi_5v_irq_handler, IRQF_ONESHOT,
+ DW_HDMI_RX_DRVNAME "-5v-handler", dw_dev);
+ if (ret)
+ goto err_wq;
+
+ /* V4L2 initialization */
+ sd = &dw_dev->sd;
+ v4l2_subdev_init(sd, &dw_hdmi_sd_ops);
+ strlcpy(sd->name, dev_name(dev), sizeof(sd->name));
+ sd->dev = dev;
+ sd->internal_ops = &dw_hdmi_internal_ops;
+ sd->flags |= V4L2_SUBDEV_FL_HAS_EVENTS;
+
+ /* V4L2 device for phy subdev */
+ strlcpy(dw_dev->v4l2_dev.name, dev_name(dev),
+ sizeof(dw_dev->v4l2_dev.name));
+ ret = v4l2_device_register(NULL, &dw_dev->v4l2_dev);
+ if (ret) {
+ dev_err(dev, "failed to register v4l2 device\n");
+ goto err_wq;
+ }
+
+ /* Notifier for subdev binding */
+ ret = dw_hdmi_v4l2_init_notifier(dw_dev);
+ if (ret) {
+ dev_err(dev, "failed to init v4l2 notifier\n");
+ goto err_v4l2_dev;
+ }
+
+ /* Phy loading */
+ ret = dw_hdmi_phy_init(dw_dev);
+ if (ret)
+ goto err_v4l2_notifier;
+
+ /* CEC */
+#if IS_ENABLED(CONFIG_VIDEO_DWC_HDMI_RX_CEC)
+ dw_dev->cec_adap = cec_allocate_adapter(&dw_hdmi_cec_adap_ops,
+ dw_dev, dev_name(dev), CEC_CAP_TRANSMIT |
+ CEC_CAP_LOG_ADDRS | CEC_CAP_RC | CEC_CAP_PASSTHROUGH,
+ HDMI_CEC_MAX_LOG_ADDRS);
+ ret = PTR_ERR_OR_ZERO(dw_dev->cec_adap);
+ if (ret) {
+ dev_err(dev, "failed to allocate CEC adapter\n");
+ goto err_phy;
+ }
+
+ dw_dev->cec_notifier = cec_notifier_get(&dw_dev->notifier_pdev->dev);
+ if (!dw_dev->cec_notifier) {
+ dev_err(dev, "failed to allocate CEC notifier\n");
+ ret = -ENOMEM;
+ goto err_cec;
+ }
+
+ dev_info(dev, "CEC is enabled\n");
+#else
+ dev_info(dev, "CEC is disabled\n");
+#endif
+
+ ret = v4l2_async_register_subdev(sd);
+ if (ret) {
+ dev_err(dev, "failed to register subdev\n");
+ goto err_cec;
+ }
+
+ /* Fill initial format settings */
+ dw_dev->timings = timings_def;
+ dw_dev->mbus_code = MEDIA_BUS_FMT_BGR888_1X24;
+
+ /* All done */
+ dev_set_drvdata(dev, sd);
+ dw_dev->state = HDMI_STATE_POWER_OFF;
+ dw_hdmi_detect_tx_5v(dw_dev);
+ dev_info(dev, "driver probed\n");
+ return 0;
+
+err_cec:
+ cec_delete_adapter(dw_dev->cec_adap);
+err_phy:
+ dw_hdmi_phy_exit(dw_dev);
+err_v4l2_notifier:
+ v4l2_async_notifier_unregister(&dw_dev->v4l2_notifier);
+err_v4l2_dev:
+ v4l2_device_unregister(&dw_dev->v4l2_dev);
+err_wq:
+ destroy_workqueue(dw_dev->wq);
+ return ret;
+}
+
+static int dw_hdmi_rx_remove(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct v4l2_subdev *sd = dev_get_drvdata(dev);
+ struct dw_hdmi_dev *dw_dev = to_dw_dev(sd);
+
+ dev_dbg(dev, "%s\n", __func__);
+
+ dw_hdmi_disable_ints(dw_dev);
+ dw_hdmi_disable_hpd(dw_dev);
+ dw_hdmi_disable_scdc(dw_dev);
+ dw_hdmi_power_off(dw_dev);
+ dw_hdmi_phy_s_power(dw_dev, false);
+ flush_workqueue(dw_dev->wq);
+ destroy_workqueue(dw_dev->wq);
+ v4l2_device_unregister(&dw_dev->v4l2_dev);
+ dw_hdmi_phy_exit(dw_dev);
+ v4l2_async_unregister_subdev(sd);
+ clk_disable_unprepare(dw_dev->clk);
+ dev_info(dev, "driver removed\n");
+ return 0;
+}
+
+static const struct of_device_id dw_hdmi_rx_id[] = {
+ { .compatible = "snps,dw-hdmi-rx" },
+ { },
+};
+MODULE_DEVICE_TABLE(of, dw_hdmi_rx_id);
+
+static struct platform_driver dw_hdmi_rx_driver = {
+ .probe = dw_hdmi_rx_probe,
+ .remove = dw_hdmi_rx_remove,
+ .driver = {
+ .name = DW_HDMI_RX_DRVNAME,
+ .of_match_table = dw_hdmi_rx_id,
+ }
+};
+module_platform_driver(dw_hdmi_rx_driver);
diff --git a/drivers/media/platform/dwc/dw-hdmi-rx.h b/drivers/media/platform/dwc/dw-hdmi-rx.h
new file mode 100644
index 0000000..14ec5a6
--- /dev/null
+++ b/drivers/media/platform/dwc/dw-hdmi-rx.h
@@ -0,0 +1,441 @@
+/*
+ * Synopsys Designware HDMI Receiver controller driver
+ *
+ * This Synopsys dw-hdmi-rx software and associated documentation
+ * (hereinafter the "Software") is an unsupported proprietary work of
+ * Synopsys, Inc. unless otherwise expressly agreed to in writing between
+ * Synopsys and you. The Software IS NOT an item of Licensed Software or a
+ * Licensed Product under any End User Software License Agreement or
+ * Agreement for Licensed Products with Synopsys or any supplement thereto.
+ * Synopsys is a registered trademark of Synopsys, Inc. Other names included
+ * in the SOFTWARE may be the trademarks of their respective owners.
+ *
+ * The contents of this file are dual-licensed; you may select either version 2
+ * of the GNU General Public License (“GPL”) or the MIT license (“MIT”).
+ *
+ * Copyright (c) 2017 Synopsys, Inc. and/or its affiliates.
+ *
+ * THIS SOFTWARE IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING, BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE, AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR
+ * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT, OR OTHERWISE
+ * ARISING FROM, OUT OF, OR IN CONNECTION WITH THE SOFTWARE THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#ifndef __DW_HDMI_RX_H__
+#define __DW_HDMI_RX_H__
+
+#include <linux/bitops.h>
+
+/* id_hdmi Registers */
+#define HDMI_SETUP_CTRL 0x0000
+#define HDMI_PLL_LCK_STS 0x0030
+#define HDMI_CKM_EVLTM 0x0094
+#define HDMI_CKM_RESULT 0x009c
+#define HDMI_STS 0x00bc
+
+/* id_hdcp_1_4 Registers */
+#define HDMI_HDCP_CTRL 0x00c0
+#define HDMI_HDCP_SETTINGS 0x00c4
+#define HDMI_HDCP_SEED 0x00c8
+#define HDMI_HDCP_BKSV1 0x00cc
+#define HDMI_HDCP_BKSV0 0x00d0
+#define HDMI_HDCP_KIDX 0x00d4
+#define HDMI_HDCP_KEY1 0x00d8
+#define HDMI_HDCP_KEY0 0x00dc
+#define HDMI_HDCP_DBG 0x00e0
+#define HDMI_HDCP_AKSV1 0x00e4
+#define HDMI_HDCP_AKSV0 0x00e8
+#define HDMI_HDCP_AN1 0x00ec
+#define HDMI_HDCP_AN0 0x00f0
+#define HDMI_HDCP_EESS_WOO 0x00f4
+#define HDMI_HDCP_I2C_TIMEOUT 0x00f8
+#define HDMI_HDCP_STS 0x00fc
+
+/* id_mode_detection Registers */
+#define HDMI_MD_HT0 0x0148
+#define HDMI_MD_HT1 0x014c
+#define HDMI_MD_HACT_PX 0x0150
+#define HDMI_MD_VCTRL 0x0158
+#define HDMI_MD_VOL 0x0164
+#define HDMI_MD_VAL 0x0168
+#define HDMI_MD_VTL 0x0170
+#define HDMI_MD_STS 0x0180
+
+/* id_phy_configuration Registers */
+#define HDMI_PHY_CTRL 0x02c0
+#define HDMI_PHY_JTAG_CONF 0x02ec
+#define HDMI_PHY_JTAG_TAP_TCLK 0x02f0
+#define HDMI_PHY_JTAG_TAP_IN 0x02f4
+#define HDMI_PHY_JTAG_TAP_OUT 0x02f8
+#define HDMI_PHY_JTAG_ADDR 0x02fc
+
+/* id_packet_decoder Registers */
+#define HDMI_PDEC_STS 0x0360
+#define HDMI_PDEC_VSI_PAYLOAD0 0x0368
+#define HDMI_PDEC_AVI_PB 0x03a4
+
+/* id_hdmi_2_0 Registers */
+#define HDMI_SCDC_CONFIG 0x0808
+#define HDMI_HDCP22_CONTROL 0x081c
+#define HDMI_HDCP22_STATUS 0x08fc
+
+/* id_audio_and_cec_interrupt Registers */
+#define HDMI_AUD_CEC_IEN_CLR 0x0f90
+#define HDMI_AUD_CEC_IEN_SET 0x0f94
+#define HDMI_AUD_CEC_ISTS 0x0f98
+#define HDMI_AUD_CEC_IEN 0x0f9c
+#define HDMI_AUD_CEC_ICLR 0x0fa0
+#define HDMI_AUD_CEC_ISET 0x0fa4
+
+/* id_mode_detection_interrupt Registers */
+#define HDMI_MD_IEN_CLR 0x0fc0
+#define HDMI_MD_IEN_SET 0x0fc4
+#define HDMI_MD_ISTS 0x0fc8
+#define HDMI_MD_IEN 0x0fcc
+#define HDMI_MD_ICLR 0x0fd0
+#define HDMI_MD_ISET 0x0fd4
+
+/* id_hdmi_interrupt Registers */
+#define HDMI_IEN_CLR 0x0fd8
+#define HDMI_IEN_SET 0x0fdc
+#define HDMI_ISTS 0x0fe0
+#define HDMI_IEN 0x0fe4
+#define HDMI_ICLR 0x0fe8
+#define HDMI_ISET 0x0fec
+
+/* id_dmi Registers */
+#define HDMI_DMI_SW_RST 0x0ff0
+
+/* id_cec Registers */
+#define HDMI_CEC_CTRL 0x1f00
+#define HDMI_CEC_MASK 0x1f08
+#define HDMI_CEC_ADDR_L 0x1f14
+#define HDMI_CEC_ADDR_H 0x1f18
+#define HDMI_CEC_TX_CNT 0x1f1c
+#define HDMI_CEC_RX_CNT 0x1f20
+#define HDMI_CEC_TX_DATA(i) (0x1f40 + ((i) * 4))
+#define HDMI_CEC_TX_DATA_MAX 16
+#define HDMI_CEC_RX_DATA(i) (0x1f80 + ((i) * 4))
+#define HDMI_CEC_RX_DATA_MAX 16
+#define HDMI_CEC_LOCK 0x1fc0
+#define HDMI_CEC_WAKEUPCTRL 0x1fc4
+
+/* id_cbus Registers */
+#define HDMI_CBUSIOCTRL 0x3020
+
+enum {
+ /* SETUP_CTRL field values */
+ HDMI_SETUP_CTRL_HOT_PLUG_DETECT_INPUT_X_MASK = GENMASK(27,24),
+ HDMI_SETUP_CTRL_HOT_PLUG_DETECT_INPUT_X_OFFSET = 24,
+ HDMI_SETUP_CTRL_HDMIBUS_RESET_OVR_EN_MASK = BIT(21),
+ HDMI_SETUP_CTRL_HDMIBUS_RESET_OVR_EN_OFFSET = 21,
+ HDMI_SETUP_CTRL_BUS_RESET_OVR_MASK = BIT(20),
+ HDMI_SETUP_CTRL_BUS_RESET_OVR_OFFSET = 20,
+ HDMI_SETUP_CTRL_HDMI_RESET_OVR_MASK = BIT(19),
+ HDMI_SETUP_CTRL_HDMI_RESET_OVR_OFFSET = 19,
+ HDMI_SETUP_CTRL_PON_RESET_OVR_MASK = BIT(18),
+ HDMI_SETUP_CTRL_PON_RESET_OVR_OFFSET = 18,
+ HDMI_SETUP_CTRL_RESET_OVR_MASK = BIT(17),
+ HDMI_SETUP_CTRL_RESET_OVR_OFFSET = 17,
+ HDMI_SETUP_CTRL_RESET_OVR_EN_MASK = BIT(16),
+ HDMI_SETUP_CTRL_RESET_OVR_EN_OFFSET = 16,
+ HDMI_SETUP_CTRL_EQ_OSM_OVR_MASK = BIT(15),
+ HDMI_SETUP_CTRL_EQ_OSM_OVR_OFFSET = 15,
+ HDMI_SETUP_CTRL_EQ_OSM_OVR_EN_MASK = BIT(14),
+ HDMI_SETUP_CTRL_EQ_OSM_OVR_EN_OFFSET = 14,
+ HDMI_SETUP_CTRL_NOWAIT_ACTIVITY_MASK = BIT(13),
+ HDMI_SETUP_CTRL_NOWAIT_ACTIVITY_OFFSET = 13,
+ HDMI_SETUP_CTRL_EQ_CAL_TIME_MASK = GENMASK(12,7),
+ HDMI_SETUP_CTRL_EQ_CAL_TIME_OFFSET = 7,
+ HDMI_SETUP_CTRL_USE_PLL_LOCK_MASK = BIT(6),
+ HDMI_SETUP_CTRL_USE_PLL_LOCK_OFFSET = 6,
+ HDMI_SETUP_CTRL_FORCE_STATE_MASK = BIT(5),
+ HDMI_SETUP_CTRL_FORCE_STATE_OFFSET = 5,
+ HDMI_SETUP_CTRL_TARGET_STATE_MASK = GENMASK(4,1),
+ HDMI_SETUP_CTRL_TARGET_STATE_OFFSET = 1,
+ HDMI_SETUP_CTRL_HOT_PLUG_DETECT_MASK = BIT(0),
+ HDMI_SETUP_CTRL_HOT_PLUG_DETECT_OFFSET = 0,
+ /* PLL_LCK_STS field values */
+ HDMI_PLL_LCK_STS_PLL_LOCKED = BIT(0),
+ /* CKM_EVLTM field values */
+ HDMI_CKM_EVLTM_LOCK_HYST_MASK = GENMASK(21,20),
+ HDMI_CKM_EVLTM_LOCK_HYST_OFFSET = 20,
+ HDMI_CKM_EVLTM_CLK_HYST_MASK = GENMASK(18,16),
+ HDMI_CKM_EVLTM_CLK_HYST_OFFSET = 16,
+ HDMI_CKM_EVLTM_EVAL_TIME_MASK = GENMASK(15,4),
+ HDMI_CKM_EVLTM_EVAL_TIME_OFFSET = 4,
+ HDMI_CKM_EVLTM_CLK_MEAS_INPUT_SRC_MASK = BIT(0),
+ HDMI_CKM_EVLTM_CLK_MEAS_INPUT_SRC_OFFSET = 0,
+ /* CKM_RESULT field values */
+ HDMI_CKM_RESULT_CLOCK_IN_RANGE = BIT(17),
+ HDMI_CKM_RESULT_FREQ_LOCKED = BIT(16),
+ HDMI_CKM_RESULT_CLKRATE_MASK = GENMASK(15,0),
+ HDMI_CKM_RESULT_CLKRATE_OFFSET = 0,
+ /* STS field values */
+ HDMI_STS_DCM_CURRENT_MODE_MASK = GENMASK(31,28),
+ HDMI_STS_DCM_CURRENT_MODE_OFFSET = 28,
+ HDMI_STS_DCM_LAST_PIXEL_PHASE_STS_MASK = GENMASK(27,24),
+ HDMI_STS_DCM_LAST_PIXEL_PHASE_STS_OFFSET = 24,
+ HDMI_STS_DCM_PHASE_DIFF_CNT_MASK = GENMASK(23,16),
+ HDMI_STS_DCM_PH_DIFF_CNT_OVERFL = BIT(15),
+ HDMI_STS_DCM_GCP_ZERO_FIELDS_PASS = BIT(14),
+ HDMI_STS_CTL3_STS = BIT(13),
+ HDMI_STS_CTL2_STS = BIT(12),
+ HDMI_STS_CTL1_STS = BIT(11),
+ HDMI_STS_CTL0_STS = BIT(10),
+ HDMI_STS_VS_POL_ADJ_STS = BIT(9),
+ HDMI_STS_HS_POL_ADJ_STS = BIT(8),
+ HDMI_STS_RES_OVERLOAD_STS = BIT(7),
+ HDMI_STS_DCM_CURRENT_PP_MASK = GENMASK(3,0),
+ HDMI_STS_DCM_CURRENT_PP_OFFSET = 0,
+ /* HDCP_CTRL field values */
+ HDMI_HDCP_CTRL_ENDISLOCK_MASK = BIT(25),
+ HDMI_HDCP_CTRL_ENDISLOCK_OFFSET = 25,
+ HDMI_HDCP_CTRL_ENABLE_MASK = BIT(24),
+ HDMI_HDCP_CTRL_ENABLE_OFFSET = 24,
+ HDMI_HDCP_CTRL_FREEZE_HDCP_FSM_MASK = BIT(21),
+ HDMI_HDCP_CTRL_FREEZE_HDCP_FSM_OFFSET = 21,
+ HDMI_HDCP_CTRL_FREEZE_HDCP_STATE_MASK = GENMASK(20,15),
+ HDMI_HDCP_CTRL_FREEZE_HDCP_STATE_OFFSET = 15,
+ HDMI_HDCP_CTRL_VID_DE_MASK = BIT(14),
+ HDMI_HDCP_CTRL_VID_DE_OFFSET = 14,
+ HDMI_HDCP_CTRL_SEL_AVMUTE_MASK = GENMASK(11,10),
+ HDMI_HDCP_CTRL_SEL_AVMUTE_OFFSET = 10,
+ HDMI_HDCP_CTRL_CTL_MASK = GENMASK(9,8),
+ HDMI_HDCP_CTRL_CTL_OFFSET = 8,
+ HDMI_HDCP_CTRL_RI_RATE_MASK = GENMASK(7,6),
+ HDMI_HDCP_CTRL_RI_RATE_OFFSET = 6,
+ HDMI_HDCP_CTRL_HDMI_MODE_ENABLE_MASK = BIT(2),
+ HDMI_HDCP_CTRL_HDMI_MODE_ENABLE_OFFSET = 2,
+ HDMI_HDCP_CTRL_KEY_DECRYPT_ENABLE_MASK = BIT(1),
+ HDMI_HDCP_CTRL_KEY_DECRYPT_ENABLE_OFFSET = 1,
+ HDMI_HDCP_CTRL_ENC_EN_MASK = BIT(0),
+ HDMI_HDCP_CTRL_ENC_EN_OFFSET = 0,
+ /* HDCP_SEED field values */
+ HDMI_HDCP_SEED_KEY_DECRYPT_SEED_MASK = GENMASK(15,0),
+ HDMI_HDCP_SEED_KEY_DECRYPT_SEED_OFFSET = 0,
+ /* HDCP_STS field values */
+ HDMI_HDCP_STS_ENC_STATE = BIT(9),
+ HDMI_HDCP_STS_AUTH_START = BIT(8),
+ HDMI_HDCP_STS_KEY_WR_OK = BIT(0),
+ /* MD_HT0 field values */
+ HDMI_MD_HT0_HTOT32_CLK_MASK = GENMASK(31,16),
+ HDMI_MD_HT0_HTOT32_CLK_OFFSET = 16,
+ HDMI_MD_HT0_HS_CLK_MASK = GENMASK(15,0),
+ HDMI_MD_HT0_HS_CLK_OFFSET = 0,
+ /* MD_HT1 field values */
+ HDMI_MD_HT1_HTOT_PIX_MASK = GENMASK(31,16),
+ HDMI_MD_HT1_HTOT_PIX_OFFSET = 16,
+ HDMI_MD_HT1_HOFS_PIX_MASK = GENMASK(15,0),
+ HDMI_MD_HT1_HOFS_PIX_OFFSET = 0,
+ /* MD_VCTRL field values */
+ HDMI_MD_VCTRL_V_OFFS_LIN_MODE_MASK = BIT(4),
+ HDMI_MD_VCTRL_V_OFFS_LIN_MODE_OFFSET = 4,
+ HDMI_MD_VCTRL_V_EDGE_MASK = BIT(1),
+ HDMI_MD_VCTRL_V_EDGE_OFFSET = 1,
+ HDMI_MD_VCTRL_V_MODE_MASK = BIT(0),
+ HDMI_MD_VCTRL_V_MODE_OFFSET = 0,
+ /* MD_STS field values */
+ HDMI_MD_STS_ILACE = BIT(3),
+ HDMI_MD_STS_DE_ACTIVITY = BIT(2),
+ HDMI_MD_STS_VS_ACT = BIT(1),
+ HDMI_MD_STS_HS_ACT = BIT(0),
+ /* PHY_CTRL field values */
+ HDMI_PHY_CTRL_SVSRETMODEZ_MASK = BIT(6),
+ HDMI_PHY_CTRL_SVSRETMODEZ_OFFSET = 6,
+ HDMI_PHY_CTRL_CFGCLKFREQ_MASK = GENMASK(5,4),
+ HDMI_PHY_CTRL_CFGCLKFREQ_OFFSET = 4,
+ HDMI_PHY_CTRL_PORTSELECT_MASK = GENMASK(3,2),
+ HDMI_PHY_CTRL_PORTSELECT_OFFSET = 2,
+ HDMI_PHY_CTRL_PDDQ_MASK = BIT(1),
+ HDMI_PHY_CTRL_PDDQ_OFFSET = 1,
+ HDMI_PHY_CTRL_RESET_MASK = BIT(0),
+ HDMI_PHY_CTRL_RESET_OFFSET = 0,
+ /* PHY_JTAG_TAP_IN field values */
+ HDMI_PHY_JTAG_TAP_IN_TMS = BIT(4),
+ HDMI_PHY_JTAG_TAP_IN_TDI = BIT(0),
+ /* PDEC_STS field values */
+ HDMI_PDEC_STS_DRM_CKS_CHG = BIT(31),
+ HDMI_PDEC_STS_DRM_RCV = BIT(30),
+ HDMI_PDEC_STS_NTSCVBI_CKS_CHG = BIT(29),
+ HDMI_PDEC_STS_DVIDET = BIT(28),
+ HDMI_PDEC_STS_VSI_CKS_CHG = BIT(27),
+ HDMI_PDEC_STS_GMD_CKS_CHG = BIT(26),
+ HDMI_PDEC_STS_AIF_CKS_CHG = BIT(25),
+ HDMI_PDEC_STS_AVI_CKS_CHG = BIT(24),
+ HDMI_PDEC_STS_ACR_N_CHG = BIT(23),
+ HDMI_PDEC_STS_ACR_CTS_CHG = BIT(22),
+ HDMI_PDEC_STS_GCP_AV_MUTE_CHG = BIT(21),
+ HDMI_PDEC_STS_GMD_RCV = BIT(20),
+ HDMI_PDEC_STS_AIF_RCV = BIT(19),
+ HDMI_PDEC_STS_AVI_RCV = BIT(18),
+ HDMI_PDEC_STS_ACR_RCV = BIT(17),
+ HDMI_PDEC_STS_GCP_RCV = BIT(16),
+ HDMI_PDEC_STS_VSI_RCV = BIT(15),
+ HDMI_PDEC_STS_AMP_RCV = BIT(14),
+ HDMI_PDEC_STS_NTSCVBI_RCV = BIT(13),
+ HDMI_PDEC_STS_OBA_LAYOUT = BIT(12),
+ HDMI_PDEC_STS_AUDS_LAYOUT = BIT(11),
+ HDMI_PDEC_STS_PD_FIFO_NEW_ENTRY = BIT(8),
+ HDMI_PDEC_STS_PD_FIFO_OVERFL = BIT(4),
+ HDMI_PDEC_STS_PD_FIFO_UNDERFL = BIT(3),
+ HDMI_PDEC_STS_PD_FIFO_TH_START_PASS = BIT(2),
+ HDMI_PDEC_STS_PD_FIFO_TH_MAX_PASS = BIT(1),
+ HDMI_PDEC_STS_PD_FIFO_TH_MIN_PASS = BIT(0),
+ /* PDEC_VSI_PAYLOAD0 field values */
+ HDMI_PDEC_VSI_PAYLOAD0_HDMI_VIC_MASK = GENMASK(15,8),
+ HDMI_PDEC_VSI_PAYLOAD0_HDMI_VIC_OFFSET = 8,
+ /* PDEC_AVI_PB field values */
+ HDMI_PDEC_AVI_PB_VID_IDENT_CODE_MASK = GENMASK(31,24),
+ HDMI_PDEC_AVI_PB_VID_IDENT_CODE_OFFSET = 24,
+ HDMI_PDEC_AVI_PB_IT_CONTENT = BIT(23),
+ HDMI_PDEC_AVI_PB_EXT_COLORIMETRY_MASK = GENMASK(22,20),
+ HDMI_PDEC_AVI_PB_EXT_COLORIMETRY_OFFSET = 20,
+ HDMI_PDEC_AVI_PB_RGB_QUANT_RANGE_MASK = GENMASK(19,18),
+ HDMI_PDEC_AVI_PB_RGB_QUANT_RANGE_OFFSET = 18,
+ HDMI_PDEC_AVI_PB_NON_UNIF_SCALE_MASK = GENMASK(17,16),
+ HDMI_PDEC_AVI_PB_NON_UNIF_SCALE_OFFSET = 16,
+ HDMI_PDEC_AVI_PB_COLORIMETRY_MASK = GENMASK(15,14),
+ HDMI_PDEC_AVI_PB_COLORIMETRY_OFFSET = 14,
+ HDMI_PDEC_AVI_PB_PIC_ASPECT_RAT_MASK = GENMASK(13,12),
+ HDMI_PDEC_AVI_PB_PIC_ASPECT_RAT_OFFSET = 12,
+ HDMI_PDEC_AVI_PB_ACT_ASPECT_RAT_MASK = GENMASK(11,8),
+ HDMI_PDEC_AVI_PB_ACT_ASPECT_RAT_OFFSET = 8,
+ HDMI_PDEC_AVI_PB_VIDEO_FORMAT_MASK = GENMASK(7,5),
+ HDMI_PDEC_AVI_PB_VIDEO_FORMAT_OFFSET = 5,
+ HDMI_PDEC_AVI_PB_ACT_INFO_PRESENT = BIT(4),
+ HDMI_PDEC_AVI_PB_BAR_INFO_VALID_MASK = GENMASK(3,2),
+ HDMI_PDEC_AVI_PB_BAR_INFO_VALID_OFFSET = 2,
+ HDMI_PDEC_AVI_PB_SCAN_INFO_MASK = GENMASK(1,0),
+ HDMI_PDEC_AVI_PB_SCAN_INFO_OFFSET = 0,
+ /* SCDC_CONFIG field values */
+ HDMI_SCDC_CONFIG_HPDLOW_MASK = BIT(1),
+ HDMI_SCDC_CONFIG_HPDLOW_OFFSET = 1,
+ HDMI_SCDC_CONFIG_POWERPROVIDED_MASK = BIT(0),
+ HDMI_SCDC_CONFIG_POWERPROVIDED_OFFSET = 0,
+ /* HDCP22_CONTROL field values */
+ HDMI_HDCP22_CONTROL_CD_OVR_VAL_MASK = GENMASK(23,20),
+ HDMI_HDCP22_CONTROL_CD_OVR_VAL_OFFSET = 20,
+ HDMI_HDCP22_CONTROL_CD_OVR_EN_MASK = BIT(16),
+ HDMI_HDCP22_CONTROL_CD_OVR_EN_OFFSET = 16,
+ HDMI_HDCP22_CONTROL_HPD_MASK = BIT(12),
+ HDMI_HDCP22_CONTROL_HPD_OFFSET = 12,
+ HDMI_HDCP22_CONTROL_PKT_ERR_OVR_VAL_MASK = BIT(9),
+ HDMI_HDCP22_CONTROL_PKT_ERR_OVR_VAL_OFFSET= 9,
+ HDMI_HDCP22_CONTROL_PKT_ERR_OVR_EN_MASK = BIT(8),
+ HDMI_HDCP22_CONTROL_PKT_ERR_OVR_EN_OFFSET = 8,
+ HDMI_HDCP22_CONTROL_AVMUTE_OVR_VAL_MASK = BIT(5),
+ HDMI_HDCP22_CONTROL_AVMUTE_OVR_VAL_OFFSET = 5,
+ HDMI_HDCP22_CONTROL_AVMUTE_OVR_EN_MASK = BIT(4),
+ HDMI_HDCP22_CONTROL_AVMUTE_OVR_EN_OFFSET = 4,
+ HDMI_HDCP22_CONTROL_OVR_VAL_MASK = BIT(2),
+ HDMI_HDCP22_CONTROL_OVR_VAL_OFFSET = 2,
+ HDMI_HDCP22_CONTROL_OVR_EN_MASK = BIT(1),
+ HDMI_HDCP22_CONTROL_OVR_EN_OFFSET = 1,
+ HDMI_HDCP22_CONTROL_SWITCH_LCK_MASK = BIT(0),
+ HDMI_HDCP22_CONTROL_SWITCH_LCK_OFFSET = 0,
+ /* AUD_CEC_ISTS field values */
+ HDMI_AUD_CEC_ISTS_WAKEUPCTRL = BIT(22),
+ HDMI_AUD_CEC_ISTS_ERROR_FOLL = BIT(21),
+ HDMI_AUD_CEC_ISTS_ERROR_INIT = BIT(20),
+ HDMI_AUD_CEC_ISTS_ARBLST = BIT(19),
+ HDMI_AUD_CEC_ISTS_NACK = BIT(18),
+ HDMI_AUD_CEC_ISTS_EOM = BIT(17),
+ HDMI_AUD_CEC_ISTS_DONE = BIT(16),
+ HDMI_AUD_CEC_ISTS_SCK_STABLE = BIT(1),
+ HDMI_AUD_CEC_ISTS_CTSN_CNT = BIT(0),
+ /* MD_ISTS field values */
+ HDMI_MD_ISTS_VOFS_LIN = BIT(11),
+ HDMI_MD_ISTS_VTOT_LIN = BIT(10),
+ HDMI_MD_ISTS_VACT_LIN = BIT(9),
+ HDMI_MD_ISTS_VS_CLK = BIT(8),
+ HDMI_MD_ISTS_VTOT_CLK = BIT(7),
+ HDMI_MD_ISTS_HACT_PIX = BIT(6),
+ HDMI_MD_ISTS_HS_CLK = BIT(5),
+ HDMI_MD_ISTS_HTOT32_CLK = BIT(4),
+ HDMI_MD_ISTS_ILACE = BIT(3),
+ HDMI_MD_ISTS_DE_ACTIVITY = BIT(2),
+ HDMI_MD_ISTS_VS_ACT = BIT(1),
+ HDMI_MD_ISTS_HS_ACT = BIT(0),
+ /* ISTS field values */
+ HDMI_ISTS_I2CMP_ARBLOST = BIT(30),
+ HDMI_ISTS_I2CMPNACK = BIT(29),
+ HDMI_ISTS_I2CMPDONE = BIT(28),
+ HDMI_ISTS_VS_THR_REACHED = BIT(27),
+ HDMI_ISTS_VSYNC_ACT_EDGE = BIT(26),
+ HDMI_ISTS_AKSV_RCV = BIT(25),
+ HDMI_ISTS_PLL_CLOCK_GATED = BIT(24),
+ HDMI_ISTS_DESER_MISAL = BIT(23),
+ HDMI_ISTS_CDSENSE_CHG = BIT(22),
+ HDMI_ISTS_CEAVID_EMPTY = BIT(21),
+ HDMI_ISTS_CEAVID_FULL = BIT(20),
+ HDMI_ISTS_SCDCTMDSCFGCHANGE = BIT(19),
+ HDMI_ISTS_SCDCSCSTATUSCHANGE = BIT(18),
+ HDMI_ISTS_SCDCCFGCHANGE = BIT(17),
+ HDMI_ISTS_DCM_CURRENT_MODE_CHG = BIT(16),
+ HDMI_ISTS_DCM_PH_DIFF_CNT_OVERFL = BIT(15),
+ HDMI_ISTS_DCM_GCP_ZERO_FIELDS_PASS = BIT(14),
+ HDMI_ISTS_CTL3_CHANGE = BIT(13),
+ HDMI_ISTS_CTL2_CHANGE = BIT(12),
+ HDMI_ISTS_CTL1_CHANGE = BIT(11),
+ HDMI_ISTS_CTL0_CHANGE = BIT(10),
+ HDMI_ISTS_VS_POL_ADJ = BIT(9),
+ HDMI_ISTS_HS_POL_ADJ = BIT(8),
+ HDMI_ISTS_RES_OVERLOAD = BIT(7),
+ HDMI_ISTS_CLK_CHANGE = BIT(6),
+ HDMI_ISTS_PLL_LCK_CHG = BIT(5),
+ HDMI_ISTS_EQGAIN_DONE = BIT(4),
+ HDMI_ISTS_OFFSCAL_DONE = BIT(3),
+ HDMI_ISTS_RESCAL_DONE = BIT(2),
+ HDMI_ISTS_ACT_CHANGE = BIT(1),
+ HDMI_ISTS_STATE_REACHED = BIT(0),
+ /* DMI_SW_RST field values */
+ HDMI_DMI_SW_RST_TMDS = BIT(16),
+ HDMI_DMI_SW_RST_HDCP = BIT(8),
+ HDMI_DMI_SW_RST_VID = BIT(7),
+ HDMI_DMI_SW_RST_PIXEL = BIT(6),
+ HDMI_DMI_SW_RST_CEC = BIT(5),
+ HDMI_DMI_SW_RST_AUD = BIT(4),
+ HDMI_DMI_SW_RST_BUS = BIT(3),
+ HDMI_DMI_SW_RST_HDMI = BIT(2),
+ HDMI_DMI_SW_RST_MODET = BIT(1),
+ HDMI_DMI_SW_RST_MAIN = BIT(0),
+ /* CEC_CTRL field values */
+ HDMI_CEC_CTRL_STANDBY_MASK = BIT(4),
+ HDMI_CEC_CTRL_STANDBY_OFFSET = 4,
+ HDMI_CEC_CTRL_BC_NACK_MASK = BIT(3),
+ HDMI_CEC_CTRL_BC_NACK_OFFSET = 3,
+ HDMI_CEC_CTRL_FRAME_TYP_MASK = GENMASK(2,1),
+ HDMI_CEC_CTRL_FRAME_TYP_OFFSET = 1,
+ HDMI_CEC_CTRL_SEND_MASK = BIT(0),
+ HDMI_CEC_CTRL_SEND_OFFSET = 0,
+ /* CEC_MASK field values */
+ HDMI_CEC_MASK_WAKEUP_MASK = BIT(6),
+ HDMI_CEC_MASK_WAKEUP_OFFSET = 6,
+ HDMI_CEC_MASK_ERROR_FLOW_MASK = BIT(5),
+ HDMI_CEC_MASK_ERROR_FLOW_OFFSET = 5,
+ HDMI_CEC_MASK_ERROR_INITITATOR_MASK = BIT(4),
+ HDMI_CEC_MASK_ERROR_INITITATOR_OFFSET = 4,
+ HDMI_CEC_MASK_ARB_LOST_MASK = BIT(3),
+ HDMI_CEC_MASK_ARB_LOST_OFFSET = 3,
+ HDMI_CEC_MASK_NACK_MASK = BIT(2),
+ HDMI_CEC_MASK_NACK_OFFSET = 2,
+ HDMI_CEC_MASK_EOM_MASK = BIT(1),
+ HDMI_CEC_MASK_EOM_OFFSET = 1,
+ HDMI_CEC_MASK_DONE_MASK = BIT(0),
+ HDMI_CEC_MASK_DONE_OFFSET = 0,
+ /* CBUSIOCTRL field values */
+ HDMI_CBUSIOCTRL_DATAPATH_CBUSZ_MASK = BIT(24),
+ HDMI_CBUSIOCTRL_DATAPATH_CBUSZ_OFFSET = 24,
+ HDMI_CBUSIOCTRL_SVSRETMODEZ_MASK = BIT(16),
+ HDMI_CBUSIOCTRL_SVSRETMODEZ_OFFSET = 16,
+ HDMI_CBUSIOCTRL_PDDQ_MASK = BIT(8),
+ HDMI_CBUSIOCTRL_PDDQ_OFFSET = 8,
+ HDMI_CBUSIOCTRL_RESET_MASK = BIT(0),
+ HDMI_CBUSIOCTRL_RESET_OFFSET = 0,
+};
+
+#endif /* __DW_HDMI_RX_H__ */
diff --git a/include/media/dwc/dw-hdmi-rx-pdata.h b/include/media/dwc/dw-hdmi-rx-pdata.h
new file mode 100644
index 0000000..38c6d91
--- /dev/null
+++ b/include/media/dwc/dw-hdmi-rx-pdata.h
@@ -0,0 +1,97 @@
+/*
+ * Synopsys Designware HDMI Receiver controller platform data
+ *
+ * This Synopsys dw-hdmi-rx software and associated documentation
+ * (hereinafter the "Software") is an unsupported proprietary work of
+ * Synopsys, Inc. unless otherwise expressly agreed to in writing between
+ * Synopsys and you. The Software IS NOT an item of Licensed Software or a
+ * Licensed Product under any End User Software License Agreement or
+ * Agreement for Licensed Products with Synopsys or any supplement thereto.
+ * Synopsys is a registered trademark of Synopsys, Inc. Other names included
+ * in the SOFTWARE may be the trademarks of their respective owners.
+ *
+ * The contents of this file are dual-licensed; you may select either version 2
+ * of the GNU General Public License (“GPL”) or the MIT license (“MIT”).
+ *
+ * Copyright (c) 2017 Synopsys, Inc. and/or its affiliates.
+ *
+ * THIS SOFTWARE IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING, BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE, AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR
+ * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT, OR OTHERWISE
+ * ARISING FROM, OUT OF, OR IN CONNECTION WITH THE SOFTWARE THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#ifndef __DW_HDMI_RX_PDATA_H__
+#define __DW_HDMI_RX_PDATA_H__
+
+#define DW_HDMI_RX_DRVNAME "dw-hdmi-rx"
+
+/* Notify events */
+#define DW_HDMI_NOTIFY_IS_OFF 1
+#define DW_HDMI_NOTIFY_INPUT_CHANGED 2
+#define DW_HDMI_NOTIFY_AUDIO_CHANGED 3
+#define DW_HDMI_NOTIFY_IS_STABLE 4
+
+/* HDCP 1.4 */
+#define DW_HDMI_HDCP14_BKSV_SIZE 2
+#define DW_HDMI_HDCP14_KEYS_SIZE (2 * 40)
+
+/**
+ * struct dw_hdmi_hdcp14_key - HDCP 1.4 keys structure.
+ *
+ * @seed: Seeed value for HDCP 1.4 engine (16 bits).
+ *
+ * @bksv: BKSV value for HDCP 1.4 engine (40 bits).
+ *
+ * @keys: Keys value for HDCP 1.4 engine (80 * 56 bits).
+ *
+ * @keys_valid: Must be set to true if the keys in this structure are valid
+ * and can be used by the HDMI receiver controller.
+ */
+struct dw_hdmi_hdcp14_key {
+ u32 seed;
+ u32 bksv[DW_HDMI_HDCP14_BKSV_SIZE];
+ u32 keys[DW_HDMI_HDCP14_KEYS_SIZE];
+ bool keys_valid;
+};
+
+/**
+ * struct dw_hdmi_rx_pdata - Platform Data configuration for HDMI receiver.
+ *
+ * @hdcp14_keys: Keys for HDCP 1.4 engine. See @dw_hdmi_hdcp14_key.
+ *
+ * @dw_5v_status: 5v status callback. Shall return the status of the given
+ * input, i.e. shall be true if a cable is connected to the specified input.
+ *
+ * @dw_5v_clear: 5v clear callback. Shall clear the interrupt associated with
+ * the 5v sense controller.
+ *
+ * @dw_5v_arg: Argument to be used with the 5v sense callbacks.
+ *
+ * @dw_zcal_reset: Impedance calibration reset callback. Shall be called when
+ * the impedance calibration needs to be restarted. This is used by phy driver
+ * only.
+ *
+ * @dw_zcal_done: Impendace calibration status callback. Shall return true if
+ * the impedance calibration procedure has ended. This is used by phy driver
+ * only.
+ *
+ * @dw_zcal_arg: Argument to be used with the ZCAL calibration callbacks.
+ */
+struct dw_hdmi_rx_pdata {
+ /* Controller configuration */
+ struct dw_hdmi_hdcp14_key hdcp14_keys;
+ /* 5V sense interface */
+ bool (*dw_5v_status)(void __iomem *regs, int input);
+ void (*dw_5v_clear)(void __iomem *regs);
+ void __iomem *dw_5v_arg;
+ /* Zcal interface */
+ void (*dw_zcal_reset)(void __iomem *regs);
+ bool (*dw_zcal_done)(void __iomem *regs);
+ void __iomem *dw_zcal_arg;
+};
+
+#endif /* __DW_HDMI_RX_PDATA_H__ */
--
1.9.1
On Tue, Jun 20, 2017 at 06:26:12PM +0100, Jose Abreu wrote:
> Document the bindings for the Synopsys Designware HDMI RX.
>
> Signed-off-by: Jose Abreu <[email protected]>
> Cc: Carlos Palminha <[email protected]>
> Cc: Rob Herring <[email protected]>
> Cc: Mark Rutland <[email protected]>
> Cc: Mauro Carvalho Chehab <[email protected]>
> Cc: Hans Verkuil <[email protected]>
> Cc: Sylwester Nawrocki <[email protected]>
>
> Changes from v3:
> - Document the new DT bindings suggested by Sylwester
> Changes from v2:
> - Document edid-phandle property
> ---
> .../devicetree/bindings/media/snps,dw-hdmi-rx.txt | 70 ++++++++++++++++++++++
> 1 file changed, 70 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/media/snps,dw-hdmi-rx.txt
>
> diff --git a/Documentation/devicetree/bindings/media/snps,dw-hdmi-rx.txt b/Documentation/devicetree/bindings/media/snps,dw-hdmi-rx.txt
> new file mode 100644
> index 0000000..efb0ac3
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/snps,dw-hdmi-rx.txt
> @@ -0,0 +1,70 @@
> +Synopsys DesignWare HDMI RX Decoder
> +===================================
> +
> +This document defines device tree properties for the Synopsys DesignWare HDMI
> +RX Decoder (DWC HDMI RX). It doesn't constitute a device tree binding
> +specification by itself but is meant to be referenced by platform-specific
> +device tree bindings.
> +
> +When referenced from platform device tree bindings the properties defined in
> +this document are defined as follows.
> +
> +- compatible: Shall be "snps,dw-hdmi-rx".
> +
> +- reg: Memory mapped base address and length of the DWC HDMI RX registers.
> +
> +- interrupts: Reference to the DWC HDMI RX interrupt and 5v sense interrupt.
> +
> +- clocks: Phandle to the config clock block.
> +
> +- clock-names: Shall be "cfg-clk".
"-clk" is redundant.
Seems strange that this is the only clock. The only other clock is the
HDMI clock from the HDMI transmitter.
> +
> +- edid-phandle: phandle to the EDID handler block.
> +
> +- #address-cells: Shall be 1.
> +
> +- #size-cells: Shall be 0.
> +
> +You also have to create a subnode for phy driver. Phy properties are as follows.
> +
> +- compatible: Shall be "snps,dw-hdmi-phy-e405".
> +
> +- reg: Shall be JTAG address of phy.
> +
> +- clocks: Phandle for cfg clock.
> +
> +- clock-names:Shall be "cfg-clk".
> +
> +A sample binding is now provided. The compatible string is for a SoC which has
> +has a Synopsys Designware HDMI RX decoder inside.
> +
> +Example:
> +
> +dw_hdmi_soc: dw-hdmi-soc@0 {
> + compatible = "snps,dw-hdmi-soc";
Not documented.
> + reg = <0x11c00 0x1000>; /* EDIDs */
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + dw_hdmi_rx@0 {
hdmi-rx@0
> + compatible = "snps,dw-hdmi-rx";
> + reg = <0x0 0x10000>;
> + interrupts = <1 2>;
> + edid-phandle = <&dw_hdmi_soc>;
Don't need this if it is the parent node.
> +
> + clocks = <&dw_hdmi_refclk>;
> + clock-names = "cfg-clk";
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + dw_hdmi_phy_e405@fc {
hdmi-phy@fc
> + compatible = "snps,dw-hdmi-phy-e405";
> + reg = <0xfc>;
> +
> + clocks = <&dw_hdmi_refclk>;
> + clock-names = "cfg-clk";
> + };
> + };
> +};
> --
> 1.9.1
>
>
Hi Jose,
Thank you for addressing my review comments. Couple more suggestions below.
On 06/20/2017 07:26 PM, Jose Abreu wrote:
> This adds support for the Synopsys Designware HDMI RX PHY e405. This
> phy receives and decodes HDMI video that is delivered to a controller.
> +static int dw_phy_config(struct dw_phy_dev *dw_dev, unsigned char color_depth,
> + bool hdmi2, bool scrambling)
> +{
> + phy_reset(dw_dev, 1);
> + phy_pddq(dw_dev, 1);
> + phy_svsmode(dw_dev, 1);
> +
> + phy_zcal_reset(dw_dev);
> + do {
> + udelay(1000);
Could be mdelay(1) or better e.g. usleep_range(1000, 1100);
> + zcal_done = phy_zcal_done(dw_dev);
> + } while (!zcal_done && timeout--);
> +
> + if (!zcal_done) {
> + dev_err(dw_dev->dev, "Zcal calibration failed\n");
> + return -ETIMEDOUT;
> + }
> + return 0;
> +}
> +static int dw_phy_probe(struct platform_device *pdev)
> +{
> + struct dw_phy_pdata *pdata = pdev->dev.platform_data;
> + struct device *dev = &pdev->dev;
> + struct dw_phy_dev *dw_dev;
> + struct v4l2_subdev *sd;
> + int ret;
> +
> + dev_dbg(dev, "probe start\n");
> +
> + /* Resource allocation */
This comment is not needed.
> + dw_dev = devm_kzalloc(dev, sizeof(*dw_dev), GFP_KERNEL);
> + if (!dw_dev)
> + return -ENOMEM;
> +
> + /* Resource initialization */
Ditto.
> + if (!pdata) {
> + dev_err(dev, "no platform data suplied\n");
> + return -EINVAL;
> + }
> +
> + dw_dev->dev = dev;
> + dw_dev->config = pdata;
> + dw_dev->version = 405;
How about storing the version number in the dw_hdmi_phy_e405_id[] table
and retrieving it here with of_device_get_match_data() ?
> + mutex_init(&dw_dev->lock);
> +
> + /* Get config clock value */
The comment is not needed, it's clear from the code we are getting the clock
and its rate.
> + dw_dev->clk = devm_clk_get(dev, "cfg-clk");
As Rob suggested, it would be good to change name of the clock to just "cfg".
> + if (IS_ERR(dw_dev->clk)) {
> + dev_err(dev, "failed to get cfg-clk\n");
> + return PTR_ERR(dw_dev->clk);
> + }
> +
> + ret = clk_prepare_enable(dw_dev->clk);
> + if (ret) {
> + dev_err(dev, "failed to enable cfg-clk\n");
> + return ret;
> + }
> +
> + dw_dev->cfg_clk = clk_get_rate(dw_dev->clk) / 1000000;
1000000U ?
> + if (!dw_dev->cfg_clk) {
> + dev_err(dev, "invalid cfg-clk frequency\n");> + ret = -EINVAL;
> + goto err_clk;
> + }
> +
> + /* V4L2 initialization */
> + sd = &dw_dev->sd;
> + v4l2_subdev_init(sd, &dw_phy_sd_ops);
> + strlcpy(sd->name, dev_name(dev), sizeof(sd->name));
> + sd->dev = dev;
> +
> + /* Force phy disabling */
> + dw_dev->phy_enabled = true;
> + dw_phy_disable(dw_dev);
> +
> + /* Register subdev */
> + ret = v4l2_async_register_subdev(sd);
> + if (ret) {
> + dev_err(dev, "failed to register subdev\n");
> + goto err_clk;
> + }
> +
> + /* All done */
Superfluous comment.
> + dev_set_drvdata(dev, sd);
> + dev_info(dev, "driver probed (cfg-clk=%d)\n", dw_dev->cfg_clk);
This should be at dev_dbg() level.
> + return 0;
> +
> +err_clk:
> + clk_disable_unprepare(dw_dev->clk);
> + return ret;
> +}
> +
> +static int dw_phy_remove(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
The assignment here could be dropped and &pdev->dev used directly below.
> + struct v4l2_subdev *sd = dev_get_drvdata(dev);
> + struct dw_phy_dev *dw_dev = to_dw_dev(sd);
> +
> + v4l2_async_unregister_subdev(sd);
> + clk_disable_unprepare(dw_dev->clk);
> + dev_info(dev, "driver removed\n");
This should be at dev_dbg() level or dropped entirely.
> + return 0;
> +}
> +
> +static const struct of_device_id dw_hdmi_phy_e405_id[] = {
> + { .compatible = "snps,dw-hdmi-phy-e405" },
> + { },
> +};
> +MODULE_DEVICE_TABLE(of, dw_hdmi_phy_e405_id);
--
Regards,
Sylwester
On 06/20/2017 07:26 PM, Jose Abreu wrote:
> This is an initial submission for the Synopsys Designware HDMI RX
> Controller Driver. This driver interacts with a phy driver so that
> a communication between them is created and a video pipeline is
> configured.
> Signed-off-by: Jose Abreu <[email protected]>
> Cc: Carlos Palminha <[email protected]>
> Cc: Mauro Carvalho Chehab <[email protected]>
> Cc: Hans Verkuil <[email protected]>
> Cc: Sylwester Nawrocki <[email protected]>
>
> Changes from v3:
> - Use v4l2 async API (Sylwester)
> - Do not block waiting for phy
> - Do not use busy waiting delays (Sylwester)
> - Simplify dw_hdmi_power_on (Sylwester)
> - Use clock API (Sylwester)
> - Use compatible string (Sylwester)
> - Minor fixes (Sylwester)
> Changes from v2:
> - Address review comments from Hans regarding CEC
> - Use CEC notifier
> - Enable SCDC
> Changes from v1:
> - Add support for CEC
> - Correct typo errors
> - Correctly detect interlaced video modes
> - Correct VIC parsing
> Changes from RFC:
> - Add support for HDCP 1.4
> - Fixup HDMI_VIC not being parsed (Hans)
> - Send source change signal when powering off (Hans)
> - Add a "wait stable delay"
> - Detect interlaced video modes (Hans)
> - Restrain g/s_register from reading/writing to HDCP regs (Hans)
> ---
> drivers/media/platform/dwc/Kconfig | 15 +
> drivers/media/platform/dwc/Makefile | 1 +
> drivers/media/platform/dwc/dw-hdmi-rx.c | 1862 +++++++++++++++++++++++++++++++
> drivers/media/platform/dwc/dw-hdmi-rx.h | 441 ++++++++
> include/media/dwc/dw-hdmi-rx-pdata.h | 97 ++
> 5 files changed, 2416 insertions(+)
> create mode 100644 drivers/media/platform/dwc/dw-hdmi-rx.c
> create mode 100644 drivers/media/platform/dwc/dw-hdmi-rx.h
> create mode 100644 include/media/dwc/dw-hdmi-rx-pdata.h
>
> diff --git a/drivers/media/platform/dwc/dw-hdmi-rx.c b/drivers/media/platform/dwc/dw-hdmi-rx.c
> new file mode 100644
> index 0000000..22ee51d
> --- /dev/null
> +++ b/drivers/media/platform/dwc/dw-hdmi-rx.c
> +static const struct of_device_id dw_hdmi_supported_phys[] = {
> + { .compatible = "snps,dw-hdmi-phy-e405", .data = DW_PHY_E405_DRVNAME, },
> + { },
> +};
> +
> +static struct device_node *dw_hdmi_get_phy_of_node(struct dw_hdmi_dev *dw_dev,
> + const struct of_device_id **found_id)
> +{
> + struct device_node *child = NULL;
> + const struct of_device_id *id;
> +
> + for_each_child_of_node(dw_dev->of_node, child) {
> + id = of_match_node(dw_hdmi_supported_phys, child);
> + if (id)
> + break;
> + }
> +
> + if (found_id)
> + *found_id = id;
> +
> + return child;
> +}
> +
> +static int dw_hdmi_phy_init(struct dw_hdmi_dev *dw_dev)
> +{
> + struct dw_phy_pdata *phy = &dw_dev->phy_config;
> + const struct of_device_id *of_id;
> + struct of_dev_auxdata lookup;
struct of_dev_auxdata lookup = { };
You could initialize to 0 here and...
> + struct device_node *child;
> + const char *drvname;
> + int ret;
> +
> + child = dw_hdmi_get_phy_of_node(dw_dev, &of_id);
> + if (!child || !of_id || !of_id->data) {
> + dev_err(dw_dev->dev, "no supported phy found in DT\n");
> + return -EINVAL;
> + }
> +
> + drvname = of_id->data;
> + phy->funcs = &dw_hdmi_phy_funcs;
> + phy->funcs_arg = dw_dev;
> +
> + lookup.compatible = (char *)of_id->compatible;
> + lookup.phys_addr = 0x0;
> + lookup.name = NULL;
...drop these two assignments.
> + lookup.platform_data = phy;
> +
> + request_module(drvname);
I'd say this request_module() is not needed when you use the v4l2-async
subnotifiers and the modules are properly installed in the file system.
I might be missing something though.
> + ret = of_platform_populate(dw_dev->of_node, NULL, &lookup, dw_dev->dev);
> + if (ret) {
> + dev_err(dw_dev->dev, "failed to populate phy driver\n");
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +static void dw_hdmi_phy_exit(struct dw_hdmi_dev *dw_dev)
> +{
> + of_platform_depopulate(dw_dev->dev);
> +}
> +static int dw_hdmi_registered(struct v4l2_subdev *sd)
> +{
> + struct dw_hdmi_dev *dw_dev = to_dw_dev(sd);
> + int ret;
> +
> + ret = cec_register_adapter(dw_dev->cec_adap, dw_dev->dev);
> + if (ret) {
> + dev_err(dw_dev->dev, "failed to register CEC adapter\n");
> + cec_delete_adapter(dw_dev->cec_adap);
> + return ret;
> + }
> +
> + cec_register_cec_notifier(dw_dev->cec_adap, dw_dev->cec_notifier);
> + dw_dev->registered = true;
> + return ret;
> +}
> +
> +static void dw_hdmi_unregistered(struct v4l2_subdev *sd)
> +{
> + struct dw_hdmi_dev *dw_dev = to_dw_dev(sd);
> +
> + cec_unregister_adapter(dw_dev->cec_adap);
> + cec_notifier_put(dw_dev->cec_notifier);
> +}
> +
> +static const struct v4l2_subdev_internal_ops dw_hdmi_internal_ops = {
> + .registered = dw_hdmi_registered,
> + .unregistered = dw_hdmi_unregistered,
> +};
> +
> +static int dw_hdmi_v4l2_notify_bound(struct v4l2_async_notifier *notifier,
> + struct v4l2_subdev *subdev, struct v4l2_async_subdev *asd)
> +{
> + struct dw_hdmi_dev *dw_dev = notifier_to_dw_dev(notifier);
> +
> + if (dw_dev->phy_async_sd.match.fwnode.fwnode ==
> + of_fwnode_handle(subdev->dev->of_node)) {
> + dev_dbg(dw_dev->dev, "found new subdev '%s'\n", subdev->name);
> + dw_dev->phy_sd = subdev;
> + return 0;
> + }
> +
> + return -EINVAL;
> +}
> +
> +static void dw_hdmi_v4l2_notify_unbind(struct v4l2_async_notifier *notifier,
> + struct v4l2_subdev *subdev, struct v4l2_async_subdev *asd)
> +{
> + struct dw_hdmi_dev *dw_dev = notifier_to_dw_dev(notifier);
> +
> + if (dw_dev->phy_sd == subdev) {
> + dev_dbg(dw_dev->dev, "unbinding '%s'\n", subdev->name);
> + dw_dev->phy_sd = NULL;
> + }
> +}
> +
> +static int dw_hdmi_v4l2_notify_complete(struct v4l2_async_notifier *notifier)
> +{
> + struct dw_hdmi_dev *dw_dev = notifier_to_dw_dev(notifier);
> + int ret;
> +
> + ret = v4l2_device_register_subdev_nodes(&dw_dev->v4l2_dev);
There shouldn't be multiple struct v4l2_device instances, instead we should
have only one created by the main driver. AFAIU, in your case it would be
driver associated with the dw-hdmi-soc DT node. And normally such a top level
driver creates subdev device nodes when its all required sub-devices are
available.
I think this patch could be useful for you:
https://patchwork.linuxtv.org/patch/41834
With that the dw-hdmi-soc driver would have it's v4l2-async notifier's
notify_complete() callback called only when both the hdmi-rx and the
hdmi-phy subdevs are registered.
> + if (ret) {
> + dev_err(dw_dev->dev, "failed to register subdev nodes\n");
> + return ret;
> + }
> +
> + return 0;
> +}
> +static int dw_hdmi_parse_dt(struct dw_hdmi_dev *dw_dev)
> +{
> + ret = clk_prepare_enable(dw_dev->clk);
> + if (ret) {
> + dev_err(dw_dev->dev, "failed to enable cfg-clk\n");
> + return ret;
> + }
> +
> + dw_dev->cfg_clk = clk_get_rate(dw_dev->clk) / 1000000;
1000000U ?
> + if (!dw_dev->cfg_clk) {
> + dev_err(dw_dev->dev, "invalid cfg-clk frequency\n");
> + ret = -EINVAL;
> + goto err_clk;
> + }
> +
> + return 0;
> +
> +err_clk:
> + clk_disable_unprepare(dw_dev->clk);
> + return ret;
> +}
> +
> +static int dw_hdmi_rx_probe(struct platform_device *pdev)
> +{
> + /* V4L2 initialization */
> + sd = &dw_dev->sd;
> + v4l2_subdev_init(sd, &dw_hdmi_sd_ops);
> + strlcpy(sd->name, dev_name(dev), sizeof(sd->name));
> + sd->dev = dev;
> + sd->internal_ops = &dw_hdmi_internal_ops;
> + sd->flags |= V4L2_SUBDEV_FL_HAS_EVENTS;
Don't you also need V4L2_SUBDEV_FL_HAS_DEVNODE flag set?
> + /* Notifier for subdev binding */
> + ret = dw_hdmi_v4l2_init_notifier(dw_dev);
> + if (ret) {
> + dev_err(dev, "failed to init v4l2 notifier\n");
> + goto err_v4l2_dev;
> + }
> +
> + /* Phy loading */
s/Phy/PHY/ ?
> + ret = dw_hdmi_phy_init(dw_dev);
> + if (ret)
> + goto err_v4l2_notifier;
> +
> + ret = v4l2_async_register_subdev(sd);
> + if (ret) {
> + dev_err(dev, "failed to register subdev\n");
> + goto err_cec;
> + }
> +
> + /* Fill initial format settings */
> + dw_dev->timings = timings_def;
> + dw_dev->mbus_code = MEDIA_BUS_FMT_BGR888_1X24;
> +
> + /* All done */
This comment seems unneeded.
> + dev_set_drvdata(dev, sd);
> + dw_dev->state = HDMI_STATE_POWER_OFF;
> + dw_hdmi_detect_tx_5v(dw_dev);
> + dev_info(dev, "driver probed\n");
dev_dbg()
> + return 0;
> +
> +err_cec:
> + cec_delete_adapter(dw_dev->cec_adap);
> +err_phy:
> + dw_hdmi_phy_exit(dw_dev);
> +err_v4l2_notifier:
> + v4l2_async_notifier_unregister(&dw_dev->v4l2_notifier);
> +err_v4l2_dev:
> + v4l2_device_unregister(&dw_dev->v4l2_dev);
> +err_wq:
> + destroy_workqueue(dw_dev->wq);
> + return ret;
> +}
> +
> +static int dw_hdmi_rx_remove(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct v4l2_subdev *sd = dev_get_drvdata(dev);
> + struct dw_hdmi_dev *dw_dev = to_dw_dev(sd);
> +
> + dev_dbg(dev, "%s\n", __func__);
> +
> + dw_hdmi_disable_ints(dw_dev);
> + dw_hdmi_disable_hpd(dw_dev);
> + dw_hdmi_disable_scdc(dw_dev);
> + dw_hdmi_power_off(dw_dev);
> + dw_hdmi_phy_s_power(dw_dev, false);
> + flush_workqueue(dw_dev->wq);
> + destroy_workqueue(dw_dev->wq);
> + v4l2_device_unregister(&dw_dev->v4l2_dev);
> + dw_hdmi_phy_exit(dw_dev);
> + v4l2_async_unregister_subdev(sd);
> + clk_disable_unprepare(dw_dev->clk);
> + dev_info(dev, "driver removed\n");
dev_dbg()
> + return 0;
> +}
> +
> +static const struct of_device_id dw_hdmi_rx_id[] = {
> + { .compatible = "snps,dw-hdmi-rx" },
> + { },
> +};
> +MODULE_DEVICE_TABLE(of, dw_hdmi_rx_id);
--
Regards,
Sylwester
Hi Rob,
On 23-06-2017 22:58, Rob Herring wrote:
> On Tue, Jun 20, 2017 at 06:26:12PM +0100, Jose Abreu wrote:
>> Document the bindings for the Synopsys Designware HDMI RX.
>>
>> Signed-off-by: Jose Abreu <[email protected]>
>> Cc: Carlos Palminha <[email protected]>
>> Cc: Rob Herring <[email protected]>
>> Cc: Mark Rutland <[email protected]>
>> Cc: Mauro Carvalho Chehab <[email protected]>
>> Cc: Hans Verkuil <[email protected]>
>> Cc: Sylwester Nawrocki <[email protected]>
>>
>> Changes from v3:
>> - Document the new DT bindings suggested by Sylwester
>> Changes from v2:
>> - Document edid-phandle property
>> ---
>> .../devicetree/bindings/media/snps,dw-hdmi-rx.txt | 70 ++++++++++++++++++++++
>> 1 file changed, 70 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/media/snps,dw-hdmi-rx.txt
>>
>> diff --git a/Documentation/devicetree/bindings/media/snps,dw-hdmi-rx.txt b/Documentation/devicetree/bindings/media/snps,dw-hdmi-rx.txt
>> new file mode 100644
>> index 0000000..efb0ac3
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/media/snps,dw-hdmi-rx.txt
>> @@ -0,0 +1,70 @@
>> +Synopsys DesignWare HDMI RX Decoder
>> +===================================
>> +
>> +This document defines device tree properties for the Synopsys DesignWare HDMI
>> +RX Decoder (DWC HDMI RX). It doesn't constitute a device tree binding
>> +specification by itself but is meant to be referenced by platform-specific
>> +device tree bindings.
>> +
>> +When referenced from platform device tree bindings the properties defined in
>> +this document are defined as follows.
>> +
>> +- compatible: Shall be "snps,dw-hdmi-rx".
>> +
>> +- reg: Memory mapped base address and length of the DWC HDMI RX registers.
>> +
>> +- interrupts: Reference to the DWC HDMI RX interrupt and 5v sense interrupt.
>> +
>> +- clocks: Phandle to the config clock block.
>> +
>> +- clock-names: Shall be "cfg-clk".
> "-clk" is redundant.
>
> Seems strange that this is the only clock. The only other clock is the
> HDMI clock from the HDMI transmitter.
Its a receiver so it gets driven by the transmitter. In my
implementation I only need to configure this clock in the
controller so that it knows the timebase. I will change to "cfg"
only then.
>
>> +
>> +- edid-phandle: phandle to the EDID handler block.
>> +
>> +- #address-cells: Shall be 1.
>> +
>> +- #size-cells: Shall be 0.
>> +
>> +You also have to create a subnode for phy driver. Phy properties are as follows.
>> +
>> +- compatible: Shall be "snps,dw-hdmi-phy-e405".
>> +
>> +- reg: Shall be JTAG address of phy.
>> +
>> +- clocks: Phandle for cfg clock.
>> +
>> +- clock-names:Shall be "cfg-clk".
>> +
>> +A sample binding is now provided. The compatible string is for a SoC which has
>> +has a Synopsys Designware HDMI RX decoder inside.
>> +
>> +Example:
>> +
>> +dw_hdmi_soc: dw-hdmi-soc@0 {
>> + compatible = "snps,dw-hdmi-soc";
> Not documented.
Yes, its a sample binding which reflects a wrapper driver that
shall instantiate the controller driver (and this wrapper driver
is not in this patch series), should I remove this?
>
>> + reg = <0x11c00 0x1000>; /* EDIDs */
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges;
>> +
>> + dw_hdmi_rx@0 {
> hdmi-rx@0
Ok.
>
>> + compatible = "snps,dw-hdmi-rx";
>> + reg = <0x0 0x10000>;
>> + interrupts = <1 2>;
>> + edid-phandle = <&dw_hdmi_soc>;
> Don't need this if it is the parent node.
Sometimes it will not be the parent node (if edid handling is
done in a separate driver, for example).
>
>> +
>> + clocks = <&dw_hdmi_refclk>;
>> + clock-names = "cfg-clk";
>> +
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + dw_hdmi_phy_e405@fc {
> hdmi-phy@fc
Ok.
>
>> + compatible = "snps,dw-hdmi-phy-e405";
>> + reg = <0xfc>;
>> +
>> + clocks = <&dw_hdmi_refclk>;
>> + clock-names = "cfg-clk";
I will also change this to "cfg" only.
Thanks for the review!
Best regards,
Jose Miguel Abreu
>> + };
>> + };
>> +};
>> --
>> 1.9.1
>>
>>
Hi Sylwester,
On 25-06-2017 22:13, Sylwester Nawrocki wrote:
> Hi Jose,
>
> Thank you for addressing my review comments. Couple more suggestions below.
>
> On 06/20/2017 07:26 PM, Jose Abreu wrote:
>> This adds support for the Synopsys Designware HDMI RX PHY e405. This
>> phy receives and decodes HDMI video that is delivered to a controller.
>> +static int dw_phy_config(struct dw_phy_dev *dw_dev, unsigned char color_depth,
>> + bool hdmi2, bool scrambling)
>> +{
>> + phy_reset(dw_dev, 1);
>> + phy_pddq(dw_dev, 1);
>> + phy_svsmode(dw_dev, 1);
>> +
>> + phy_zcal_reset(dw_dev);
>> + do {
>> + udelay(1000);
> Could be mdelay(1) or better e.g. usleep_range(1000, 1100);
Ok.
>
>> + zcal_done = phy_zcal_done(dw_dev);
>> + } while (!zcal_done && timeout--);
>> +
>> + if (!zcal_done) {
>> + dev_err(dw_dev->dev, "Zcal calibration failed\n");
>> + return -ETIMEDOUT;
>> + }
>> + return 0;
>> +}
>> +static int dw_phy_probe(struct platform_device *pdev)
>> +{
>> + struct dw_phy_pdata *pdata = pdev->dev.platform_data;
>> + struct device *dev = &pdev->dev;
>> + struct dw_phy_dev *dw_dev;
>> + struct v4l2_subdev *sd;
>> + int ret;
>> +
>> + dev_dbg(dev, "probe start\n");
>> +
>> + /* Resource allocation */
> This comment is not needed.
>
>> + dw_dev = devm_kzalloc(dev, sizeof(*dw_dev), GFP_KERNEL);
>> + if (!dw_dev)
>> + return -ENOMEM;
>> +
>> + /* Resource initialization */
> Ditto.
Ok.
>
>> + if (!pdata) {
>> + dev_err(dev, "no platform data suplied\n");
>> + return -EINVAL;
>> + }
>> +
>> + dw_dev->dev = dev;
>> + dw_dev->config = pdata;
>> + dw_dev->version = 405;
> How about storing the version number in the dw_hdmi_phy_e405_id[] table
> and retrieving it here with of_device_get_match_data() ?
Yeah, seems nice :)
>
>> + mutex_init(&dw_dev->lock);
>> +
>> + /* Get config clock value */
> The comment is not needed, it's clear from the code we are getting the clock
> and its rate.
Ok.
>
>> + dw_dev->clk = devm_clk_get(dev, "cfg-clk");
> As Rob suggested, it would be good to change name of the clock to just "cfg".
Yes, I will change.
>
>> + if (IS_ERR(dw_dev->clk)) {
>> + dev_err(dev, "failed to get cfg-clk\n");
>> + return PTR_ERR(dw_dev->clk);
>> + }
>> +
>> + ret = clk_prepare_enable(dw_dev->clk);
>> + if (ret) {
>> + dev_err(dev, "failed to enable cfg-clk\n");
>> + return ret;
>> + }
>> +
>> + dw_dev->cfg_clk = clk_get_rate(dw_dev->clk) / 1000000;
> 1000000U ?
Ok.
>
>> + if (!dw_dev->cfg_clk) {
>> + dev_err(dev, "invalid cfg-clk frequency\n");> + ret = -EINVAL;
>> + goto err_clk;
>> + }
>> +
>> + /* V4L2 initialization */
>> + sd = &dw_dev->sd;
>> + v4l2_subdev_init(sd, &dw_phy_sd_ops);
>> + strlcpy(sd->name, dev_name(dev), sizeof(sd->name));
>> + sd->dev = dev;
>> +
>> + /* Force phy disabling */
>> + dw_dev->phy_enabled = true;
>> + dw_phy_disable(dw_dev);
>> +
>> + /* Register subdev */
>> + ret = v4l2_async_register_subdev(sd);
>> + if (ret) {
>> + dev_err(dev, "failed to register subdev\n");
>> + goto err_clk;
>> + }
>> +
>> + /* All done */
> Superfluous comment.
Ok.
>
>> + dev_set_drvdata(dev, sd);
>> + dev_info(dev, "driver probed (cfg-clk=%d)\n", dw_dev->cfg_clk);
> This should be at dev_dbg() level.
Ok.
>
>> + return 0;
>> +
>> +err_clk:
>> + clk_disable_unprepare(dw_dev->clk);
>> + return ret;
>> +}
>> +
>> +static int dw_phy_remove(struct platform_device *pdev)
>> +{
>> + struct device *dev = &pdev->dev;
> The assignment here could be dropped and &pdev->dev used directly below.
Ok.
>
>> + struct v4l2_subdev *sd = dev_get_drvdata(dev);
>> + struct dw_phy_dev *dw_dev = to_dw_dev(sd);
>> +
>> + v4l2_async_unregister_subdev(sd);
>> + clk_disable_unprepare(dw_dev->clk);
>> + dev_info(dev, "driver removed\n");
> This should be at dev_dbg() level or dropped entirely.
Ok.
Thanks for the review!
Best regards,
Jose Miguel Abreu
>
>> + return 0;
>> +}
>> +
>> +static const struct of_device_id dw_hdmi_phy_e405_id[] = {
>> + { .compatible = "snps,dw-hdmi-phy-e405" },
>> + { },
>> +};
>> +MODULE_DEVICE_TABLE(of, dw_hdmi_phy_e405_id);
> --
> Regards,
> Sylwester
Hi Sylwester,
On 25-06-2017 22:13, Sylwester Nawrocki wrote:
> On 06/20/2017 07:26 PM, Jose Abreu wrote:
>> This is an initial submission for the Synopsys Designware HDMI RX
>> Controller Driver. This driver interacts with a phy driver so that
>> a communication between them is created and a video pipeline is
>> configured.
>> Signed-off-by: Jose Abreu <[email protected]>
>> Cc: Carlos Palminha <[email protected]>
>> Cc: Mauro Carvalho Chehab <[email protected]>
>> Cc: Hans Verkuil <[email protected]>
>> Cc: Sylwester Nawrocki <[email protected]>
>>
>> Changes from v3:
>> - Use v4l2 async API (Sylwester)
>> - Do not block waiting for phy
>> - Do not use busy waiting delays (Sylwester)
>> - Simplify dw_hdmi_power_on (Sylwester)
>> - Use clock API (Sylwester)
>> - Use compatible string (Sylwester)
>> - Minor fixes (Sylwester)
>> Changes from v2:
>> - Address review comments from Hans regarding CEC
>> - Use CEC notifier
>> - Enable SCDC
>> Changes from v1:
>> - Add support for CEC
>> - Correct typo errors
>> - Correctly detect interlaced video modes
>> - Correct VIC parsing
>> Changes from RFC:
>> - Add support for HDCP 1.4
>> - Fixup HDMI_VIC not being parsed (Hans)
>> - Send source change signal when powering off (Hans)
>> - Add a "wait stable delay"
>> - Detect interlaced video modes (Hans)
>> - Restrain g/s_register from reading/writing to HDCP regs (Hans)
>> ---
>> drivers/media/platform/dwc/Kconfig | 15 +
>> drivers/media/platform/dwc/Makefile | 1 +
>> drivers/media/platform/dwc/dw-hdmi-rx.c | 1862 +++++++++++++++++++++++++++++++
>> drivers/media/platform/dwc/dw-hdmi-rx.h | 441 ++++++++
>> include/media/dwc/dw-hdmi-rx-pdata.h | 97 ++
>> 5 files changed, 2416 insertions(+)
>> create mode 100644 drivers/media/platform/dwc/dw-hdmi-rx.c
>> create mode 100644 drivers/media/platform/dwc/dw-hdmi-rx.h
>> create mode 100644 include/media/dwc/dw-hdmi-rx-pdata.h
>>
>> diff --git a/drivers/media/platform/dwc/dw-hdmi-rx.c b/drivers/media/platform/dwc/dw-hdmi-rx.c
>> new file mode 100644
>> index 0000000..22ee51d
>> --- /dev/null
>> +++ b/drivers/media/platform/dwc/dw-hdmi-rx.c
>> +static const struct of_device_id dw_hdmi_supported_phys[] = {
>> + { .compatible = "snps,dw-hdmi-phy-e405", .data = DW_PHY_E405_DRVNAME, },
>> + { },
>> +};
>> +
>> +static struct device_node *dw_hdmi_get_phy_of_node(struct dw_hdmi_dev *dw_dev,
>> + const struct of_device_id **found_id)
>> +{
>> + struct device_node *child = NULL;
>> + const struct of_device_id *id;
>> +
>> + for_each_child_of_node(dw_dev->of_node, child) {
>> + id = of_match_node(dw_hdmi_supported_phys, child);
>> + if (id)
>> + break;
>> + }
>> +
>> + if (found_id)
>> + *found_id = id;
>> +
>> + return child;
>> +}
>> +
>> +static int dw_hdmi_phy_init(struct dw_hdmi_dev *dw_dev)
>> +{
>> + struct dw_phy_pdata *phy = &dw_dev->phy_config;
>> + const struct of_device_id *of_id;
>> + struct of_dev_auxdata lookup;
> struct of_dev_auxdata lookup = { };
>
> You could initialize to 0 here and...
>
>> + struct device_node *child;
>> + const char *drvname;
>> + int ret;
>> +
>> + child = dw_hdmi_get_phy_of_node(dw_dev, &of_id);
>> + if (!child || !of_id || !of_id->data) {
>> + dev_err(dw_dev->dev, "no supported phy found in DT\n");
>> + return -EINVAL;
>> + }
>> +
>> + drvname = of_id->data;
>> + phy->funcs = &dw_hdmi_phy_funcs;
>> + phy->funcs_arg = dw_dev;
>> +
>> + lookup.compatible = (char *)of_id->compatible;
>> + lookup.phys_addr = 0x0;
>> + lookup.name = NULL;
> ...drop these two assignments.
Ok.
>
>> + lookup.platform_data = phy;
>> +
>> + request_module(drvname);
> I'd say this request_module() is not needed when you use the v4l2-async
> subnotifiers and the modules are properly installed in the file system.
> I might be missing something though.
Hmm, well I didn't actually test without request_module but I
think its needed, otherwise I would have to do:
modprobe phy_module
modprobe controller_module
With request_module I just have to do:
modprobe controller_module
>
>> + ret = of_platform_populate(dw_dev->of_node, NULL, &lookup, dw_dev->dev);
>> + if (ret) {
>> + dev_err(dw_dev->dev, "failed to populate phy driver\n");
>> + return ret;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static void dw_hdmi_phy_exit(struct dw_hdmi_dev *dw_dev)
>> +{
>> + of_platform_depopulate(dw_dev->dev);
>> +}
>> +static int dw_hdmi_registered(struct v4l2_subdev *sd)
>> +{
>> + struct dw_hdmi_dev *dw_dev = to_dw_dev(sd);
>> + int ret;
>> +
>> + ret = cec_register_adapter(dw_dev->cec_adap, dw_dev->dev);
>> + if (ret) {
>> + dev_err(dw_dev->dev, "failed to register CEC adapter\n");
>> + cec_delete_adapter(dw_dev->cec_adap);
>> + return ret;
>> + }
>> +
>> + cec_register_cec_notifier(dw_dev->cec_adap, dw_dev->cec_notifier);
>> + dw_dev->registered = true;
>> + return ret;
>> +}
>> +
>> +static void dw_hdmi_unregistered(struct v4l2_subdev *sd)
>> +{
>> + struct dw_hdmi_dev *dw_dev = to_dw_dev(sd);
>> +
>> + cec_unregister_adapter(dw_dev->cec_adap);
>> + cec_notifier_put(dw_dev->cec_notifier);
>> +}
>> +
>> +static const struct v4l2_subdev_internal_ops dw_hdmi_internal_ops = {
>> + .registered = dw_hdmi_registered,
>> + .unregistered = dw_hdmi_unregistered,
>> +};
>> +
>> +static int dw_hdmi_v4l2_notify_bound(struct v4l2_async_notifier *notifier,
>> + struct v4l2_subdev *subdev, struct v4l2_async_subdev *asd)
>> +{
>> + struct dw_hdmi_dev *dw_dev = notifier_to_dw_dev(notifier);
>> +
>> + if (dw_dev->phy_async_sd.match.fwnode.fwnode ==
>> + of_fwnode_handle(subdev->dev->of_node)) {
>> + dev_dbg(dw_dev->dev, "found new subdev '%s'\n", subdev->name);
>> + dw_dev->phy_sd = subdev;
>> + return 0;
>> + }
>> +
>> + return -EINVAL;
>> +}
>> +
>> +static void dw_hdmi_v4l2_notify_unbind(struct v4l2_async_notifier *notifier,
>> + struct v4l2_subdev *subdev, struct v4l2_async_subdev *asd)
>> +{
>> + struct dw_hdmi_dev *dw_dev = notifier_to_dw_dev(notifier);
>> +
>> + if (dw_dev->phy_sd == subdev) {
>> + dev_dbg(dw_dev->dev, "unbinding '%s'\n", subdev->name);
>> + dw_dev->phy_sd = NULL;
>> + }
>> +}
>> +
>> +static int dw_hdmi_v4l2_notify_complete(struct v4l2_async_notifier *notifier)
>> +{
>> + struct dw_hdmi_dev *dw_dev = notifier_to_dw_dev(notifier);
>> + int ret;
>> +
>> + ret = v4l2_device_register_subdev_nodes(&dw_dev->v4l2_dev);
> There shouldn't be multiple struct v4l2_device instances, instead we should
> have only one created by the main driver. AFAIU, in your case it would be
> driver associated with the dw-hdmi-soc DT node. And normally such a top level
> driver creates subdev device nodes when its all required sub-devices are
> available.
>
> I think this patch could be useful for you:
> https://urldefense.proofpoint.com/v2/url?u=https-3A__patchwork.linuxtv.org_patch_41834&d=DwICaQ&c=DPL6_X_6JkXFx7AXWqB0tg&r=WHDsc6kcWAl4i96Vm5hJ_19IJiuxx_p_Rzo2g-uHDKw&m=VfuOK5-A8h_JQk0lk74o48aav0T2PnwxhIr2sauw46Y&s=0GuG3FNbkmfVVMYQuP-Ed6zY9PnXnw7S4KgQhG52JF4&e=
>
> With that the dw-hdmi-soc driver would have it's v4l2-async notifier's
> notify_complete() callback called only when both the hdmi-rx and the
> hdmi-phy subdevs are registered.
Yeah, I saw the patches. I just implemented this way because they
are not merged yet, right?
>
>> + if (ret) {
>> + dev_err(dw_dev->dev, "failed to register subdev nodes\n");
>> + return ret;
>> + }
>> +
>> + return 0;
>> +}
>> +static int dw_hdmi_parse_dt(struct dw_hdmi_dev *dw_dev)
>> +{
>> + ret = clk_prepare_enable(dw_dev->clk);
>> + if (ret) {
>> + dev_err(dw_dev->dev, "failed to enable cfg-clk\n");
>> + return ret;
>> + }
>> +
>> + dw_dev->cfg_clk = clk_get_rate(dw_dev->clk) / 1000000;
> 1000000U ?
Ok.
>
>> + if (!dw_dev->cfg_clk) {
>> + dev_err(dw_dev->dev, "invalid cfg-clk frequency\n");
>> + ret = -EINVAL;
>> + goto err_clk;
>> + }
>> +
>> + return 0;
>> +
>> +err_clk:
>> + clk_disable_unprepare(dw_dev->clk);
>> + return ret;
>> +}
>> +
>> +static int dw_hdmi_rx_probe(struct platform_device *pdev)
>> +{
>> + /* V4L2 initialization */
>> + sd = &dw_dev->sd;
>> + v4l2_subdev_init(sd, &dw_hdmi_sd_ops);
>> + strlcpy(sd->name, dev_name(dev), sizeof(sd->name));
>> + sd->dev = dev;
>> + sd->internal_ops = &dw_hdmi_internal_ops;
>> + sd->flags |= V4L2_SUBDEV_FL_HAS_EVENTS;
> Don't you also need V4L2_SUBDEV_FL_HAS_DEVNODE flag set?
Ouch. Yes I need otherwise the subdev will not be associated with
the v4l2_device.
>
>> + /* Notifier for subdev binding */
>> + ret = dw_hdmi_v4l2_init_notifier(dw_dev);
>> + if (ret) {
>> + dev_err(dev, "failed to init v4l2 notifier\n");
>> + goto err_v4l2_dev;
>> + }
>> +
>> + /* Phy loading */
> s/Phy/PHY/ ?
Ok.
>
>> + ret = dw_hdmi_phy_init(dw_dev);
>> + if (ret)
>> + goto err_v4l2_notifier;
>> +
>> + ret = v4l2_async_register_subdev(sd);
>> + if (ret) {
>> + dev_err(dev, "failed to register subdev\n");
>> + goto err_cec;
>> + }
>> +
>> + /* Fill initial format settings */
>> + dw_dev->timings = timings_def;
>> + dw_dev->mbus_code = MEDIA_BUS_FMT_BGR888_1X24;
>> +
>> + /* All done */
> This comment seems unneeded.
Ok.
>
>> + dev_set_drvdata(dev, sd);
>> + dw_dev->state = HDMI_STATE_POWER_OFF;
>> + dw_hdmi_detect_tx_5v(dw_dev);
>> + dev_info(dev, "driver probed\n");
> dev_dbg()
Ok.
>
>> + return 0;
>> +
>> +err_cec:
>> + cec_delete_adapter(dw_dev->cec_adap);
>> +err_phy:
>> + dw_hdmi_phy_exit(dw_dev);
>> +err_v4l2_notifier:
>> + v4l2_async_notifier_unregister(&dw_dev->v4l2_notifier);
>> +err_v4l2_dev:
>> + v4l2_device_unregister(&dw_dev->v4l2_dev);
>> +err_wq:
>> + destroy_workqueue(dw_dev->wq);
>> + return ret;
>> +}
>> +
>> +static int dw_hdmi_rx_remove(struct platform_device *pdev)
>> +{
>> + struct device *dev = &pdev->dev;
>> + struct v4l2_subdev *sd = dev_get_drvdata(dev);
>> + struct dw_hdmi_dev *dw_dev = to_dw_dev(sd);
>> +
>> + dev_dbg(dev, "%s\n", __func__);
>> +
>> + dw_hdmi_disable_ints(dw_dev);
>> + dw_hdmi_disable_hpd(dw_dev);
>> + dw_hdmi_disable_scdc(dw_dev);
>> + dw_hdmi_power_off(dw_dev);
>> + dw_hdmi_phy_s_power(dw_dev, false);
>> + flush_workqueue(dw_dev->wq);
>> + destroy_workqueue(dw_dev->wq);
>> + v4l2_device_unregister(&dw_dev->v4l2_dev);
>> + dw_hdmi_phy_exit(dw_dev);
>> + v4l2_async_unregister_subdev(sd);
>> + clk_disable_unprepare(dw_dev->clk);
>> + dev_info(dev, "driver removed\n");
> dev_dbg()
Ok.
Thanks for the review!
Best regards,
Jose Miguel Abreu
>
>> + return 0;
>> +}
>> +
>> +static const struct of_device_id dw_hdmi_rx_id[] = {
>> + { .compatible = "snps,dw-hdmi-rx" },
>> + { },
>> +};
>> +MODULE_DEVICE_TABLE(of, dw_hdmi_rx_id);
> --
> Regards,
> Sylwester
Hi Jose,
On 06/27/2017 10:43 AM, Jose Abreu wrote:
> On 25-06-2017 22:13, Sylwester Nawrocki wrote:
>> On 06/20/2017 07:26 PM, Jose Abreu wrote:
>>> This is an initial submission for the Synopsys Designware HDMI RX
>>> Controller Driver. This driver interacts with a phy driver so that
>>> a communication between them is created and a video pipeline is
>>> configured.
>>> Signed-off-by: Jose Abreu <[email protected]>
>>> +static int dw_hdmi_phy_init(struct dw_hdmi_dev *dw_dev)
>>> +{
>>> + struct dw_phy_pdata *phy = &dw_dev->phy_config;
>>> + const struct of_device_id *of_id;
>>> + struct of_dev_auxdata lookup;
>> struct of_dev_auxdata lookup = { };
>>
>> You could initialize to 0 here and...
>>
>>> + struct device_node *child;
>>> + const char *drvname;
>>> + int ret;
>>> +
>>> + child = dw_hdmi_get_phy_of_node(dw_dev, &of_id);
>>> + if (!child || !of_id || !of_id->data) {
>>> + dev_err(dw_dev->dev, "no supported phy found in DT\n");
>>> + return -EINVAL;
>>> + }
>>> +
>>> + drvname = of_id->data;
>>> + phy->funcs = &dw_hdmi_phy_funcs;
>>> + phy->funcs_arg = dw_dev;
>>> +
>>> + lookup.compatible = (char *)of_id->compatible;
>>> + lookup.phys_addr = 0x0;
>>> + lookup.name = NULL;
>>
>> ...drop these two assignments.
>
> Ok.
>
>>> + lookup.platform_data = phy;
>>> +
>>> + request_module(drvname);
>>
>> I'd say this request_module() is not needed when you use the v4l2-async
>> subnotifiers and the modules are properly installed in the file system.
>> I might be missing something though.
>
> Hmm, well I didn't actually test without request_module but I
> think its needed, otherwise I would have to do:
>
> modprobe phy_module
> modprobe controller_module
>
> With request_module I just have to do:
>
> modprobe controller_module
If you are sure you need it I'm not against that. But assuming you have udev
in your system it should also work like this, without request_module():
1. modprobe controller_module -> phy device is created in the kernel, uevent sent
2. udev receives uevent, finds matching module and does modprobe phy_module
Remaining part is as before: phy_module registers the driver which gets matched with
phy device; probe() is called which registers v4l2 subdev which then is registered
to v4l2_device through the v4l2-async mechanism.
All this assumes udev is running and modules are installed in /lib/modules/$(uname -r).
E.g. there should be your module alias as shown by modinfo phy_module in
/lib/modules/$(uname -r)/modules.alias.
>>> + ret = of_platform_populate(dw_dev->of_node, NULL, &lookup, dw_dev->dev);
>>> + if (ret) {
>>> + dev_err(dw_dev->dev, "failed to populate phy driver\n");
>>> + return ret;
>>> + }
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static void dw_hdmi_phy_exit(struct dw_hdmi_dev *dw_dev)
>>> +{
>>> + of_platform_depopulate(dw_dev->dev);
>>> +}
>>> +static int dw_hdmi_v4l2_notify_complete(struct v4l2_async_notifier *notifier)
>>> +{
>>> + struct dw_hdmi_dev *dw_dev = notifier_to_dw_dev(notifier);
>>> + int ret;
>>> +
>>> + ret = v4l2_device_register_subdev_nodes(&dw_dev->v4l2_dev);
>>
>> There shouldn't be multiple struct v4l2_device instances, instead we should
>> have only one created by the main driver. AFAIU, in your case it would be
>> driver associated with the dw-hdmi-soc DT node. And normally such a top level
>> driver creates subdev device nodes when its all required sub-devices are
>> available.
>>
>> I think this patch could be useful for you:
>> https://patchwork.linuxtv.org/patch/41834
>>
>> With that the dw-hdmi-soc driver would have it's v4l2-async notifier's
>> notify_complete() callback called only when both the hdmi-rx and the
>> hdmi-phy subdevs are registered.
>
> Yeah, I saw the patches. I just implemented this way because they
> are not merged yet, right?
I think these patches will be merged in v4.14-rc1, so together with your driver.
You could apply them locally and indicate that your series depends on them in
the cover letter.
>>> + if (ret) {
>>> + dev_err(dw_dev->dev, "failed to register subdev nodes\n");
>>> + return ret;
>>> + }
>>> +
>>> + return 0;
>>> +}
>>> +static int dw_hdmi_rx_probe(struct platform_device *pdev)
>>> +{
>>> + /* V4L2 initialization */
>>> + sd = &dw_dev->sd;
>>> + v4l2_subdev_init(sd, &dw_hdmi_sd_ops);
>>> + strlcpy(sd->name, dev_name(dev), sizeof(sd->name));
>>> + sd->dev = dev;
>>> + sd->internal_ops = &dw_hdmi_internal_ops;
>>> + sd->flags |= V4L2_SUBDEV_FL_HAS_EVENTS;
>>
>> Don't you also need V4L2_SUBDEV_FL_HAS_DEVNODE flag set?
>
> Ouch. Yes I need otherwise the subdev will not be associated with
> the v4l2_device.
This flag indicates that the v4l2 subdev device node (/dev/v4l-subdev?)
should be created for this subdevice.
---
Regards,
Sylwester
Hi Sylwester,
On 27-06-2017 21:34, Sylwester Nawrocki wrote:
> Hi Jose,
>
> On 06/27/2017 10:43 AM, Jose Abreu wrote:
>> On 25-06-2017 22:13, Sylwester Nawrocki wrote:
>>> On 06/20/2017 07:26 PM, Jose Abreu wrote:
>>>> This is an initial submission for the Synopsys Designware HDMI RX
>>>> Controller Driver. This driver interacts with a phy driver so that
>>>> a communication between them is created and a video pipeline is
>>>> configured.
>>>> Signed-off-by: Jose Abreu <[email protected]>
>>>> +static int dw_hdmi_phy_init(struct dw_hdmi_dev *dw_dev)
>>>> +{
>>>> + struct dw_phy_pdata *phy = &dw_dev->phy_config;
>>>> + const struct of_device_id *of_id;
>>>> + struct of_dev_auxdata lookup;
>>> struct of_dev_auxdata lookup = { };
>>>
>>> You could initialize to 0 here and...
>>>
>>>> + struct device_node *child;
>>>> + const char *drvname;
>>>> + int ret;
>>>> +
>>>> + child = dw_hdmi_get_phy_of_node(dw_dev, &of_id);
>>>> + if (!child || !of_id || !of_id->data) {
>>>> + dev_err(dw_dev->dev, "no supported phy found in DT\n");
>>>> + return -EINVAL;
>>>> + }
>>>> +
>>>> + drvname = of_id->data;
>>>> + phy->funcs = &dw_hdmi_phy_funcs;
>>>> + phy->funcs_arg = dw_dev;
>>>> +
>>>> + lookup.compatible = (char *)of_id->compatible;
>>>> + lookup.phys_addr = 0x0;
>>>> + lookup.name = NULL;
>>> ...drop these two assignments.
>> Ok.
>>
>>>> + lookup.platform_data = phy;
>>>> +
>>>> + request_module(drvname);
>>> I'd say this request_module() is not needed when you use the v4l2-async
>>> subnotifiers and the modules are properly installed in the file system.
>>> I might be missing something though.
>> Hmm, well I didn't actually test without request_module but I
>> think its needed, otherwise I would have to do:
>>
>> modprobe phy_module
>> modprobe controller_module
>>
>> With request_module I just have to do:
>>
>> modprobe controller_module
> If you are sure you need it I'm not against that. But assuming you have udev
> in your system it should also work like this, without request_module():
>
> 1. modprobe controller_module -> phy device is created in the kernel, uevent sent
> 2. udev receives uevent, finds matching module and does modprobe phy_module
>
> Remaining part is as before: phy_module registers the driver which gets matched with
> phy device; probe() is called which registers v4l2 subdev which then is registered
> to v4l2_device through the v4l2-async mechanism.
>
> All this assumes udev is running and modules are installed in /lib/modules/$(uname -r).
> E.g. there should be your module alias as shown by modinfo phy_module in
> /lib/modules/$(uname -r)/modules.alias.
The modules are installed but I think I don't have udev :/ I'm
running this on an embedded platform called ARC AXS and I'm using
buildroot with minimal options.
>
>>>> + ret = of_platform_populate(dw_dev->of_node, NULL, &lookup, dw_dev->dev);
>>>> + if (ret) {
>>>> + dev_err(dw_dev->dev, "failed to populate phy driver\n");
>>>> + return ret;
>>>> + }
>>>> +
>>>> + return 0;
>>>> +}
>>>> +
>>>> +static void dw_hdmi_phy_exit(struct dw_hdmi_dev *dw_dev)
>>>> +{
>>>> + of_platform_depopulate(dw_dev->dev);
>>>> +}
>>>> +static int dw_hdmi_v4l2_notify_complete(struct v4l2_async_notifier *notifier)
>>>> +{
>>>> + struct dw_hdmi_dev *dw_dev = notifier_to_dw_dev(notifier);
>>>> + int ret;
>>>> +
>>>> + ret = v4l2_device_register_subdev_nodes(&dw_dev->v4l2_dev);
>>> There shouldn't be multiple struct v4l2_device instances, instead we should
>>> have only one created by the main driver. AFAIU, in your case it would be
>>> driver associated with the dw-hdmi-soc DT node. And normally such a top level
>>> driver creates subdev device nodes when its all required sub-devices are
>>> available.
>>>
>>> I think this patch could be useful for you:
>>> https://urldefense.proofpoint.com/v2/url?u=https-3A__patchwork.linuxtv.org_patch_41834&d=DwICaQ&c=DPL6_X_6JkXFx7AXWqB0tg&r=WHDsc6kcWAl4i96Vm5hJ_19IJiuxx_p_Rzo2g-uHDKw&m=uNHRQkbP_-z8v5d30KFx9pcPEUhlr4ciWY3ZDAVExTA&s=dB9wpgeP7AJg1eDRty0-RKhq3DY-7J5srIzyVoJey5I&e=
>>>
>>> With that the dw-hdmi-soc driver would have it's v4l2-async notifier's
>>> notify_complete() callback called only when both the hdmi-rx and the
>>> hdmi-phy subdevs are registered.
>> Yeah, I saw the patches. I just implemented this way because they
>> are not merged yet, right?
> I think these patches will be merged in v4.14-rc1, so together with your driver.
> You could apply them locally and indicate that your series depends on them in
> the cover letter.
Ok, will apply them locally and re-test.
>
>>>> + if (ret) {
>>>> + dev_err(dw_dev->dev, "failed to register subdev nodes\n");
>>>> + return ret;
>>>> + }
>>>> +
>>>> + return 0;
>>>> +}
>>>> +static int dw_hdmi_rx_probe(struct platform_device *pdev)
>>>> +{
>>>> + /* V4L2 initialization */
>>>> + sd = &dw_dev->sd;
>>>> + v4l2_subdev_init(sd, &dw_hdmi_sd_ops);
>>>> + strlcpy(sd->name, dev_name(dev), sizeof(sd->name));
>>>> + sd->dev = dev;
>>>> + sd->internal_ops = &dw_hdmi_internal_ops;
>>>> + sd->flags |= V4L2_SUBDEV_FL_HAS_EVENTS;
>>> Don't you also need V4L2_SUBDEV_FL_HAS_DEVNODE flag set?
>> Ouch. Yes I need otherwise the subdev will not be associated with
>> the v4l2_device.
> This flag indicates that the v4l2 subdev device node (/dev/v4l-subdev?)
> should be created for this subdevice.
Ok, will add for controller driver only then: I think for phy
this should not be added because controller is responsible to
manage phy entirely so creating a /dev/ which can be seen by
userspace can lead to confusion, maybe?
Best regards,
Jose Miguel Abreu
>
> ---
> Regards,
> Sylwester
>
Hi Jose,
On 06/28/2017 11:25 AM, Jose Abreu wrote:
> On 27-06-2017 21:34, Sylwester Nawrocki wrote:
>> On 06/27/2017 10:43 AM, Jose Abreu wrote:
>>> On 25-06-2017 22:13, Sylwester Nawrocki wrote:
>>>> On 06/20/2017 07:26 PM, Jose Abreu wrote:
>>>>> This is an initial submission for the Synopsys Designware HDMI RX
>>>>> Controller Driver. This driver interacts with a phy driver so that
>>>>> a communication between them is created and a video pipeline is
>>>>> configured.
>>>>> Signed-off-by: Jose Abreu <[email protected]>
> The modules are installed but I think I don't have udev :/ I'm
> running this on an embedded platform called ARC AXS and I'm using
> buildroot with minimal options.
OK, then let's keep this request_module.
>>>>> +static int dw_hdmi_v4l2_notify_complete(struct v4l2_async_notifier *notifier)
>>>>> +{
>>>>> + struct dw_hdmi_dev *dw_dev = notifier_to_dw_dev(notifier);
>>>>> + int ret;
>>>>> +
>>>>> + ret = v4l2_device_register_subdev_nodes(&dw_dev->v4l2_dev);
>>>> There shouldn't be multiple struct v4l2_device instances, instead we should
>>>> have only one created by the main driver. AFAIU, in your case it would be
>>>> driver associated with the dw-hdmi-soc DT node. And normally such a top level
>>>> driver creates subdev device nodes when its all required sub-devices are
>>>> available.
>>>>
>>>> I think this patch could be useful for you:
>>>> https://urldefense.proofpoint.com/v2/url?u=https-3A__patchwork.linuxtv.
>>>> org_patch_41834&d=DwICaQ&c=DPL6_X_6JkXFx7AXWqB0tg&r=WHDsc6kcWAl4i96Vm5hJ_19I
>>>> Jiuxx_p_Rzo2g-uHDKw&m=uNHRQkbP_-z8v5d30KFx9pcPEUhlr4ciWY3ZDAVExTA&s=dB9wpgeP
>>>> 7AJg1eDRty0-RKhq3DY-7J5srIzyVoJey5I&e=
>>>>
>>>> With that the dw-hdmi-soc driver would have it's v4l2-async notifier's
>>>> notify_complete() callback called only when both the hdmi-rx and the
>>>> hdmi-phy subdevs are registered.
>>> Yeah, I saw the patches. I just implemented this way because they
>>> are not merged yet, right?
>>
>> I think these patches will be merged in v4.14-rc1, so together with your driver.
>> You could apply them locally and indicate that your series depends on them in
>> the cover letter.
>
> Ok, will apply them locally and re-test.
Thanks.
>>>>> + if (ret) {
>>>>> + dev_err(dw_dev->dev, "failed to register subdev nodes\n");
>>>>> + return ret;
>>>>> + }
>>>>> +
>>>>> + return 0;
>>>>> +}
>>>>> +static int dw_hdmi_rx_probe(struct platform_device *pdev)
>>>>> +{
>>>>> + /* V4L2 initialization */
>>>>> + sd = &dw_dev->sd;
>>>>> + v4l2_subdev_init(sd, &dw_hdmi_sd_ops);
>>>>> + strlcpy(sd->name, dev_name(dev), sizeof(sd->name));
>>>>> + sd->dev = dev;
>>>>> + sd->internal_ops = &dw_hdmi_internal_ops;
>>>>> + sd->flags |= V4L2_SUBDEV_FL_HAS_EVENTS;
>>>>
>>>> Don't you also need V4L2_SUBDEV_FL_HAS_DEVNODE flag set?
>>> Ouch. Yes I need otherwise the subdev will not be associated with
>>> the v4l2_device.
>>
>> This flag indicates that the v4l2 subdev device node (/dev/v4l-subdev?)
>> should be created for this subdevice.
>
> Ok, will add for controller driver only then: I think for phy
> this should not be added because controller is responsible to
> manage phy entirely so creating a /dev/ which can be seen by
> userspace can lead to confusion, maybe?
Right, there should be no need for the PHY. It's up to you to
set it or not for the RX controller subdev. I just got confused
because in your dw_hdmi_sd_ops data structure there are ops which
would suggest that device node is used.
Regards,
Sylwester
On Mon, Jun 26, 2017 at 11:42 AM, Jose Abreu <[email protected]> wrote:
> Hi Rob,
>
>
> On 23-06-2017 22:58, Rob Herring wrote:
>> On Tue, Jun 20, 2017 at 06:26:12PM +0100, Jose Abreu wrote:
>>> Document the bindings for the Synopsys Designware HDMI RX.
>>>
[...]
>>> +A sample binding is now provided. The compatible string is for a SoC which has
>>> +has a Synopsys Designware HDMI RX decoder inside.
>>> +
>>> +Example:
>>> +
>>> +dw_hdmi_soc: dw-hdmi-soc@0 {
>>> + compatible = "snps,dw-hdmi-soc";
>> Not documented.
>
> Yes, its a sample binding which reflects a wrapper driver that
> shall instantiate the controller driver (and this wrapper driver
> is not in this patch series), should I remove this?
Ah, I see. Please don't do this wrapper node like what was done on
DWC3. It should be all one node with the SoC specific part being a new
compatible string (and maybe additional properties). If there's really
some custom logic around the IP block, then maybe it makes sense, but
if it is just different clock connections, phys, resets, etc. those
don't need a separate node.
Rob
Hi Rob,
On 10-07-2017 16:24, Rob Herring wrote:
> On Mon, Jun 26, 2017 at 11:42 AM, Jose Abreu <[email protected]> wrote:
>> Hi Rob,
>>
>>
>> On 23-06-2017 22:58, Rob Herring wrote:
>>> On Tue, Jun 20, 2017 at 06:26:12PM +0100, Jose Abreu wrote:
>>>> Document the bindings for the Synopsys Designware HDMI RX.
>>>>
> [...]
>
>>>> +A sample binding is now provided. The compatible string is for a SoC which has
>>>> +has a Synopsys Designware HDMI RX decoder inside.
>>>> +
>>>> +Example:
>>>> +
>>>> +dw_hdmi_soc: dw-hdmi-soc@0 {
>>>> + compatible = "snps,dw-hdmi-soc";
>>> Not documented.
>> Yes, its a sample binding which reflects a wrapper driver that
>> shall instantiate the controller driver (and this wrapper driver
>> is not in this patch series), should I remove this?
> Ah, I see. Please don't do this wrapper node like what was done on
> DWC3. It should be all one node with the SoC specific part being a new
> compatible string (and maybe additional properties). If there's really
> some custom logic around the IP block, then maybe it makes sense, but
> if it is just different clock connections, phys, resets, etc. those
> don't need a separate node.
Ok. I guess I can just drop the SoC specific bindings as this was
more of a sample as how the EDID handle can be specified. I just
sent v8 now with the new bindings :) Thanks!
Best regards,
Jose Miguel Abreu
>
> Rob