This documents and add intial dts support for Samsung Galaxy Z Fold5 (samsung,q5q)
which is a foldable phone by Samsung based on the sm8550 SoC.
ChangeLog
- v5
. Added ChangeLog
. Added missing Acked-by tags in their respective section in ChangeLog
- v4
. removed a spurious new line
. removed pcie_1_phy_aux_clk as requested
. removed secondary pcie1 which does not exists on the device
. changed firmware extension from .mbn to .mdt
. added missing reserved memory regions required by firmware to properly load
- v3
. added b4 version 3
. removed address and size cells in device description
Acked-by: Rob Herring <[email protected]>
- v2
. added both but added an extra v2 in the subject line instead to b4 subject header, was requested to send the patch again, along with following mods:
. removed whole bootargs line
. fixed underscores in reserved memory by removing all reserved memory regions
. added missing idetation to spash_screen remark
. validated the dts with "dtbs_check"
. removed all comments at the end of nodes
. moved status of the node at the end of the node
. reversed pin control name with control numbers
. ordered the nodes alphabetically
- v1
. The initial request was split in two patches sent due to the following checkpatch warning, was requested to re send them together:
WARNING: DT binding docs and includes should be a separate patch. See: Documentation/devicetree/bindings/submitting-patches.rst
Acked-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Alexandru Marc Serdeliuc <[email protected]>
---
Alexandru Marc Serdeliuc (2):
dt-bindings: arm: qcom: Document the Samsung Galaxy Z Fold5
arm64: dts: qcom: sm8550: Add support for Samsung Galaxy Z Fold5
Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/sm8550-samsung-q5q.dts | 593 ++++++++++++++++++++++++
3 files changed, 595 insertions(+)
---
base-commit: 2c71fdf02a95b3dd425b42f28fd47fb2b1d22702
change-id: 20240410-samsung-galaxy-zfold5-q5q-d31cdeeac09f
Best regards,
--
Alexandru Marc Serdeliuc <[email protected]>
From: Alexandru Marc Serdeliuc <[email protected]>
Add support for Samsung Galaxy Z Fold5 (q5q) foldable phone based on sm8550
Currently working features:
- Framebuffer
- UFS
- i2c
- Buttons
Signed-off-by: Alexandru Marc Serdeliuc <[email protected]>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/sm8550-samsung-q5q.dts | 593 ++++++++++++++++++++++++
2 files changed, 594 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 7d40ec5e7d21..a7503fd35b6c 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -241,6 +241,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8450-sony-xperia-nagara-pdx224.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8550-hdk.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8550-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8550-qrd.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sm8550-samsung-q5q.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8650-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8650-qrd.dtb
dtb-$(CONFIG_ARCH_QCOM) += x1e80100-crd.dtb
diff --git a/arch/arm64/boot/dts/qcom/sm8550-samsung-q5q.dts b/arch/arm64/boot/dts/qcom/sm8550-samsung-q5q.dts
new file mode 100644
index 000000000000..4654ae1364ba
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm8550-samsung-q5q.dts
@@ -0,0 +1,593 @@
+// SPDX-License-cdsp_memIdentifier: BSD-3-Clause
+/*
+ * Copyright (c) 2024, Alexandru Marc Serdeliuc <[email protected]>
+ * Copyright (c) 2024, David Wronek <[email protected]>
+ * Copyright (c) 2022, Linaro Limited
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "sm8550.dtsi"
+#include "pm8550.dtsi"
+#include "pm8550vs.dtsi"
+#include "pmk8550.dtsi"
+
+/delete-node/ &adspslpi_mem;
+/delete-node/ &cdsp_mem;
+/delete-node/ &mpss_dsm_mem;
+/delete-node/ &mpss_mem;
+/delete-node/ &rmtfs_mem;
+
+/ {
+ model = "Samsung Galaxy Z Fold5";
+ compatible = "samsung,q5q", "qcom,sm8550";
+ chassis-type = "handset";
+
+ aliases {
+ serial0 = &uart7;
+ };
+
+ chosen {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ framebuffer: framebuffer@b8000000 {
+ compatible = "simple-framebuffer";
+ reg = <0x0 0xb8000000 0x0 0x2b00000>;
+ width = <2176>;
+ height = <1812>;
+ stride = <(2176 * 4)>;
+ format = "a8r8g8b8";
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&volume_up_n>;
+ pinctrl-names = "default";
+
+ key-volume-up {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ gpios = <&pm8550_gpios 6 GPIO_ACTIVE_LOW>;
+ debounce-interval = <15>;
+ linux,can-disable;
+ wakeup-source;
+ };
+ };
+
+ vph_pwr: vph-pwr-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vph_pwr";
+ regulator-min-microvolt = <3700000>;
+ regulator-max-microvolt = <3700000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ reserved-memory {
+ adspslpi_mem: adspslpi@9ea00000 {
+ reg = <0x0 0x9ea00000 0x0 0x59b4000>;
+ no-map;
+ };
+
+ cdsp_mem: cdsp-region@9c900000 {
+ reg = <0 0x9c900000 0 0x2000000>;
+ no-map;
+ };
+
+ mpss_dsm_mem: mpss-dsm@d4d00000 {
+ reg = <0x0 0xd4d00000 0x0 0x3300000>;
+ no-map;
+ };
+
+ mpss_mem: mpss@8b400000 {
+ reg = <0x0 0x8b400000 0x0 0xfc00000>;
+ no-map;
+ };
+
+ rmtfs_mem: rmtfs-region@d4a80000 {
+ reg = <0x0 0xd4a80000 0x0 0x280000>;
+ no-map;
+ };
+
+ /*
+ * The bootloader will only keep display hardware enabled
+ * if this memory region is named exactly 'splash_region'
+ */
+ splash_region@b8000000 {
+ reg = <0x0 0xb8000000 0x0 0x2b00000>;
+ no-map;
+ };
+ };
+};
+
+&apps_rsc {
+ regulators-0 {
+ compatible = "qcom,pm8550-rpmh-regulators";
+ qcom,pmic-id = "b";
+
+ vreg_bob1: bob1 {
+ regulator-name = "vreg_bob1";
+ regulator-min-microvolt = <3296000>;
+ regulator-max-microvolt = <3960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_bob2: bob2 {
+ regulator-name = "vreg_bob2";
+ regulator-min-microvolt = <2720000>;
+ regulator-max-microvolt = <3960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1b_1p8: ldo1 {
+ regulator-name = "vreg_l1b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2b_3p0: ldo2 {
+ regulator-name = "vreg_l2b_3p0";
+ regulator-min-microvolt = <3008000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5b_3p1: ldo5 {
+ regulator-name = "vreg_l5b_3p1";
+ regulator-min-microvolt = <3104000>;
+ regulator-max-microvolt = <3104000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6b_1p8: ldo6 {
+ regulator-name = "vreg_l6b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7b_1p8: ldo7 {
+ regulator-name = "vreg_l7b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l8b_1p8: ldo8 {
+ regulator-name = "vreg_l8b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l9b_2p9: ldo9 {
+ regulator-name = "vreg_l9b_2p9";
+ regulator-min-microvolt = <2960000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l11b_1p2: ldo11 {
+ regulator-name = "vreg_l11b_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1504000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l12b_1p8: ldo12 {
+ regulator-name = "vreg_l12b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l13b_3p0: ldo13 {
+ regulator-name = "vreg_l13b_3p0";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l14b_3p2: ldo14 {
+ regulator-name = "vreg_l14b_3p2";
+ regulator-min-microvolt = <3200000>;
+ regulator-max-microvolt = <3200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l15b_1p8: ldo15 {
+ regulator-name = "vreg_l15b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ regulator-always-on;
+ };
+
+ vreg_l16b_2p8: ldo16 {
+ regulator-name = "vreg_l16b_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l17b_2p5: ldo17 {
+ regulator-name = "vreg_l17b_2p5";
+ regulator-min-microvolt = <2504000>;
+ regulator-max-microvolt = <2504000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-1 {
+ compatible = "qcom,pm8550vs-rpmh-regulators";
+ qcom,pmic-id = "c";
+
+ vreg_l3c_0p91: ldo3 {
+ regulator-name = "vreg_l3c_0p9";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-2 {
+ compatible = "qcom,pm8550vs-rpmh-regulators";
+ qcom,pmic-id = "d";
+
+ vreg_l1d_0p88: ldo1 {
+ regulator-name = "vreg_l1d_0p88";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <920000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-3 {
+ compatible = "qcom,pm8550vs-rpmh-regulators";
+ qcom,pmic-id = "e";
+
+ vreg_s4e_0p9: smps4 {
+ regulator-name = "vreg_s4e_0p9";
+ regulator-min-microvolt = <904000>;
+ regulator-max-microvolt = <984000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s5e_1p1: smps5 {
+ regulator-name = "vreg_s5e_1p1";
+ regulator-min-microvolt = <1080000>;
+ regulator-max-microvolt = <1120000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1e_0p88: ldo1 {
+ regulator-name = "vreg_l1e_0p88";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2e_0p9: ldo2 {
+ regulator-name = "vreg_l2e_0p9";
+ regulator-min-microvolt = <904000>;
+ regulator-max-microvolt = <970000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3e_1p2: ldo3 {
+ regulator-name = "vreg_l3e_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-4 {
+ compatible = "qcom,pm8550ve-rpmh-regulators";
+ qcom,pmic-id = "f";
+
+ vreg_s4f_0p5: smps4 {
+ regulator-name = "vreg_s4f_0p5";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <700000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1f_0p9: ldo1 {
+ regulator-name = "vreg_l1f_0p9";
+ regulator-min-microvolt = <912000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2f_0p88: ldo2 {
+ regulator-name = "vreg_l2f_0p88";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3f_0p91: ldo3 {
+ regulator-name = "vreg_l3f_0p91";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-5 {
+ compatible = "qcom,pm8550vs-rpmh-regulators";
+ qcom,pmic-id = "g";
+
+ vreg_s1g_1p2: smps1 {
+ regulator-name = "vreg_s1g_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s2g_0p8: smps2 {
+ regulator-name = "vreg_s2g_0p8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s3g_0p7: smps3 {
+ regulator-name = "vreg_s3g_0p7";
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1004000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s4g_1p3: smps4 {
+ regulator-name = "vreg_s4g_1p3";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1352000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s5g_0p8: smps5 {
+ regulator-name = "vreg_s5g_0p8";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1004000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s6g_1p8: smps6 {
+ regulator-name = "vreg_s6g_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1g_1p2: ldo1 {
+ regulator-name = "vreg_l1g_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2g_1p2: ldo2 {
+ regulator-name = "vreg_l2g_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3g_1p2: ldo3 {
+ regulator-name = "vreg_l3g_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-6 {
+ compatible = "qcom,pm8010-rpmh-regulators";
+ qcom,pmic-id = "m";
+
+ vreg_l1m_1p056: ldo1 {
+ regulator-name = "vreg_l1m_1p056";
+ regulator-min-microvolt = <1056000>;
+ regulator-max-microvolt = <1056000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2m_1p056: ldo2 {
+ regulator-name = "vreg_l2m_1p056";
+ regulator-min-microvolt = <1056000>;
+ regulator-max-microvolt = <1056000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3m_2p8: ldo3 {
+ regulator-name = "vreg_l3m_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4m_2p8: ldo4 {
+ regulator-name = "vreg_l4m_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5m_1p8: ldo5 {
+ regulator-name = "vreg_l5m_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6m_1p8: ldo6 {
+ regulator-name = "vreg_l6m_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7m_2p9: ldo7 {
+ regulator-name = "vreg_l7m_2p9";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2904000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-7 {
+ compatible = "qcom,pm8010-rpmh-regulators";
+ qcom,pmic-id = "n";
+
+ vreg_l1n_1p1: ldo1 {
+ regulator-name = "vreg_l1n_1p1";
+ regulator-min-microvolt = <1104000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2n_1p1: ldo2 {
+ regulator-name = "vreg_l2n_1p1";
+ regulator-min-microvolt = <1104000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3n_2p8: ldo3 {
+ regulator-name = "vreg_l3n_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4n_2p8: ldo4 {
+ regulator-name = "vreg_l4n_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5n_1p8: ldo5 {
+ regulator-name = "vreg_l5n_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6n_3p3: ldo6 {
+ regulator-name = "vreg_l6n_3p3";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7n_2p96: ldo7 {
+ regulator-name = "vreg_l7n_2p96";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+};
+
+&dispcc {
+ status = "disabled";
+};
+
+&i2c_master_hub_0 {
+ status = "okay";
+};
+
+&pcie0 {
+ wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+ perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
+ pinctrl-0 = <&pcie0_default_state>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&pcie0_phy {
+ vdda-phy-supply = <&vreg_l1e_0p88>;
+ vdda-pll-supply = <&vreg_l3e_1p2>;
+ status = "okay";
+};
+
+&pm8550_gpios {
+ volume_up_n: volume-up-n-state {
+ pins = "gpio6";
+ function = "normal";
+ power-source = <1>;
+ bias-pull-up;
+ input-enable;
+ };
+};
+
+&pon_pwrkey {
+ status = "okay";
+};
+
+&pon_resin {
+ status = "okay";
+ linux,code = <KEY_VOLUMEDOWN>;
+};
+
+&qupv3_id_0 {
+ status = "okay";
+};
+
+&remoteproc_adsp {
+ firmware-name = "qcom/sm8550/adsp.mdt",
+ "qcom/sm8550/adsp_dtb.mdt";
+ status = "okay";
+};
+
+&remoteproc_cdsp {
+ firmware-name = "qcom/sm8550/cdsp.mdt",
+ "qcom/sm8550/cdsp_dtb.mdt";
+ status = "okay";
+};
+
+&remoteproc_mpss {
+ firmware-name = "qcom/sm8550/modem.mdt",
+ "qcom/sm8550/modem_dtb.mdt";
+ status = "okay";
+};
+
+&sleep_clk {
+ clock-frequency = <32000>;
+};
+
+&tlmm {
+ gpio-reserved-ranges = <36 4>, <50 2>;
+};
+
+&ufs_mem_hc {
+ reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>;
+ vcc-supply = <&vreg_l17b_2p5>;
+ vcc-max-microamp = <1300000>;
+ vccq-supply = <&vreg_l1g_1p2>;
+ vccq-max-microamp = <1200000>;
+ vdd-hba-supply = <&vreg_l3g_1p2>;
+ status = "okay";
+};
+
+&ufs_mem_phy {
+ vdda-phy-supply = <&vreg_l1d_0p88>;
+ vdda-pll-supply = <&vreg_l3e_1p2>;
+ status = "okay";
+};
+
+&xo_board {
+ clock-frequency = <76800000>;
+};
--
2.34.1
From: Alexandru Marc Serdeliuc <[email protected]>
This documents Samsung Galaxy Z Fold5 (samsung,q5q)
which is a foldable phone by Samsung based on the sm8550 SoC.
Signed-off-by: Alexandru Marc Serdeliuc <[email protected]>
---
Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index 66beaac60e1d..dea2a23b8fc2 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -1003,6 +1003,7 @@ properties:
- qcom,sm8550-hdk
- qcom,sm8550-mtp
- qcom,sm8550-qrd
+ - samsung,q5q
- const: qcom,sm8550
- items:
--
2.34.1
On 10/04/2024 23:28, Alexandru Marc Serdeliuc via B4 Relay wrote:
> This documents and add intial dts support for Samsung Galaxy Z Fold5 (samsung,q5q)
> which is a foldable phone by Samsung based on the sm8550 SoC.
>
> ChangeLog
>
> - v5
> . Added ChangeLog
> . Added missing Acked-by tags in their respective section in ChangeLog
Where? I cannot find anything.
Best regards,
Krzysztof
On 11/04/2024 08:36, Alexandru Serdeliuc wrote:
> Hi,
>
> The list of changes (changelog) from the cover is not what I should add?
>
> My patches received only two ACK tags, on V3 and on the initial request
> (v1), I was not able to identify any other, I added them to their place
> in the change log
>
> ...
> - v3
> . added b4 version 3
> . removed address and size cells in device description
> Acked-by: Rob Herring<[email protected]>
> ...
> - v1
> . The initial request was split in two patches sent due to the following checkpatch warning, was requested to re send them together:
> WARNING: DT binding docs and includes should be a separate patch. See: Documentation/devicetree/bindings/submitting-patches.rst
> Acked-by: Krzysztof Kozlowski<[email protected]>
>
> I suppose that adding them to their place in change log is wrong, I
> should create a v6 and put them at the end of the cover letter? Or how
> to proceed?
Please don't top post. If you add them to the changelog, how are they
going to be effective? Please apply your patch (e.g. b4 shazam) and look
for them...
Submitting patches explains where to add tags. Look at other mailings.
And finally: why even bothering about this if b4 does it for you?
https://elixir.bootlin.com/linux/v6.5-rc3/source/Documentation/process/submitting-patches.rst#L577
Best regards,
Krzysztof
On 11/04/2024 09:34, Krzysztof Kozlowski wrote:
> On 11/04/2024 08:36, Alexandru Serdeliuc wrote:
>> Hi,
>>
>> The list of changes (changelog) from the cover is not what I should add?
>>
>> My patches received only two ACK tags, on V3 and on the initial request
>> (v1), I was not able to identify any other, I added them to their place
>> in the change log
>>
>> ...
>> - v3
>> . added b4 version 3
>> . removed address and size cells in device description
>> Acked-by: Rob Herring<[email protected]>
>> ...
>> - v1
>> . The initial request was split in two patches sent due to the following checkpatch warning, was requested to re send them together:
>> WARNING: DT binding docs and includes should be a separate patch. See: Documentation/devicetree/bindings/submitting-patches.rst
>> Acked-by: Krzysztof Kozlowski<[email protected]>
>>
>> I suppose that adding them to their place in change log is wrong, I
>> should create a v6 and put them at the end of the cover letter? Or how
>> to proceed?
>
> Please don't top post. If you add them to the changelog, how are they
> going to be effective? Please apply your patch (e.g. b4 shazam) and look
> for them...
>
> Submitting patches explains where to add tags. Look at other mailings.
> And finally: why even bothering about this if b4 does it for you?
>
BTW, in reply to your first posting I gave you detailed instruction how
to proceed with tags. Let me quote:
"Please add Acked-by/Reviewed-by/Tested-by tags when posting new
versions, under or above your Signed-off-by tag"
I think it is clear where you should add it. I gave this instruction on
purpose so we will avoid this mess...
Drop all invalid acks from cover letter and send v6 with proper tags
places in mentioned place.
Best regards,
Krzysztof
Hi Krzysztof,
Thank you for your time and please excuse my lack of knowledge,
reviewing the first reply I clearly see now the details, but i missed
them initially, I suppose that due to the lack of knowledge in regards
to the procedures here.
I am going to generate a v6, thanks again for your valuable time spent
helping me.
Best regards,
Alexandru Marc Serdeliuc
On 11/4/24 10:47, Krzysztof Kozlowski wrote:
> On 11/04/2024 09:34, Krzysztof Kozlowski wrote:
>> On 11/04/2024 08:36, Alexandru Serdeliuc wrote:
>>> Hi,
>>>
>>> The list of changes (changelog) from the cover is not what I should add?
>>>
>>> My patches received only two ACK tags, on V3 and on the initial request
>>> (v1), I was not able to identify any other, I added them to their place
>>> in the change log
>>>
>>> ...
>>> - v3
>>> . added b4 version 3
>>> . removed address and size cells in device description
>>> Acked-by: Rob Herring<[email protected]>
>>> ...
>>> - v1
>>> . The initial request was split in two patches sent due to the following checkpatch warning, was requested to re send them together:
>>> WARNING: DT binding docs and includes should be a separate patch. See: Documentation/devicetree/bindings/submitting-patches.rst
>>> Acked-by: Krzysztof Kozlowski<[email protected]>
>>>
>>> I suppose that adding them to their place in change log is wrong, I
>>> should create a v6 and put them at the end of the cover letter? Or how
>>> to proceed?
>> Please don't top post. If you add them to the changelog, how are they
>> going to be effective? Please apply your patch (e.g. b4 shazam) and look
>> for them...
>>
>> Submitting patches explains where to add tags. Look at other mailings.
>> And finally: why even bothering about this if b4 does it for you?
>>
> BTW, in reply to your first posting I gave you detailed instruction how
> to proceed with tags. Let me quote:
>
> "Please add Acked-by/Reviewed-by/Tested-by tags when posting new
> versions, under or above your Signed-off-by tag"
>
> I think it is clear where you should add it. I gave this instruction on
> purpose so we will avoid this mess...
>
> Drop all invalid acks from cover letter and send v6 with proper tags
> places in mentioned place.
>
> Best regards,
> Krzysztof
>
On Wed, 10 Apr 2024 23:28:32 +0200, Alexandru Marc Serdeliuc wrote:
> This documents and add intial dts support for Samsung Galaxy Z Fold5 (samsung,q5q)
> which is a foldable phone by Samsung based on the sm8550 SoC.
>
> ChangeLog
>
> - v5
> . Added ChangeLog
> . Added missing Acked-by tags in their respective section in ChangeLog
>
> - v4
> . removed a spurious new line
> . removed pcie_1_phy_aux_clk as requested
> . removed secondary pcie1 which does not exists on the device
> . changed firmware extension from .mbn to .mdt
> . added missing reserved memory regions required by firmware to properly load
>
> - v3
> . added b4 version 3
> . removed address and size cells in device description
> Acked-by: Rob Herring <[email protected]>
>
> - v2
> . added both but added an extra v2 in the subject line instead to b4 subject header, was requested to send the patch again, along with following mods:
> . removed whole bootargs line
> . fixed underscores in reserved memory by removing all reserved memory regions
> . added missing idetation to spash_screen remark
> . validated the dts with "dtbs_check"
> . removed all comments at the end of nodes
> . moved status of the node at the end of the node
> . reversed pin control name with control numbers
> . ordered the nodes alphabetically
>
> - v1
> . The initial request was split in two patches sent due to the following checkpatch warning, was requested to re send them together:
> WARNING: DT binding docs and includes should be a separate patch. See: Documentation/devicetree/bindings/submitting-patches.rst
> Acked-by: Krzysztof Kozlowski <[email protected]>
>
> Signed-off-by: Alexandru Marc Serdeliuc <[email protected]>
> ---
> Alexandru Marc Serdeliuc (2):
> dt-bindings: arm: qcom: Document the Samsung Galaxy Z Fold5
> arm64: dts: qcom: sm8550: Add support for Samsung Galaxy Z Fold5
>
> Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
> arch/arm64/boot/dts/qcom/Makefile | 1 +
> arch/arm64/boot/dts/qcom/sm8550-samsung-q5q.dts | 593 ++++++++++++++++++++++++
> 3 files changed, 595 insertions(+)
> ---
> base-commit: 2c71fdf02a95b3dd425b42f28fd47fb2b1d22702
> change-id: 20240410-samsung-galaxy-zfold5-q5q-d31cdeeac09f
>
> Best regards,
> --
> Alexandru Marc Serdeliuc <[email protected]>
>
>
>
My bot found new DTB warnings on the .dts files added or changed in this
series.
Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
are fixed by another series. Ultimately, it is up to the platform
maintainer whether these warnings are acceptable or not. No need to reply
unless the platform maintainer has comments.
If you already ran DT checks and didn't see these error(s), then
make sure dt-schema is up to date:
pip3 install dtschema --upgrade
New warnings running 'make CHECK_DTBS=y qcom/sm8550-samsung-q5q.dtb' for [email protected]:
arch/arm64/boot/dts/qcom/sm8550-samsung-q5q.dtb: pcie-1-phy-aux-clk: 'clock-frequency' is a required property
from schema $id: http://devicetree.org/schemas/clock/fixed-clock.yaml#
arch/arm64/boot/dts/qcom/sm8550-samsung-q5q.dtb: phy@1c0e000: clock-output-names: ['pcie1_pipe_clk'] is too short
from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-pcie-phy.yaml#
arch/arm64/boot/dts/qcom/sm8550-samsung-q5q.dtb: phy@1c0e000: #clock-cells:0:0: 1 was expected
from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-pcie-phy.yaml#