From: Oleksandr Andrushchenko <[email protected]>
It is possible that drm_simple_kms_plane_atomic_check called
with no CRTC set, e.g. when user-space application sets CRTC_ID/FB_ID
to 0 before doing any actual drawing. This leads to NULL pointer
dereference because in this case new CRTC state is NULL and must be
checked before accessing.
Signed-off-by: Oleksandr Andrushchenko <[email protected]>
---
drivers/gpu/drm/drm_simple_kms_helper.c | 6 ++++--
1 file changed, 4 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/drm_simple_kms_helper.c b/drivers/gpu/drm/drm_simple_kms_helper.c
index 9ca8a4a59b74..a05eca9cec8b 100644
--- a/drivers/gpu/drm/drm_simple_kms_helper.c
+++ b/drivers/gpu/drm/drm_simple_kms_helper.c
@@ -121,8 +121,10 @@ static int drm_simple_kms_plane_atomic_check(struct drm_plane *plane,
pipe = container_of(plane, struct drm_simple_display_pipe, plane);
crtc_state = drm_atomic_get_new_crtc_state(plane_state->state,
&pipe->crtc);
- if (!crtc_state->enable)
- return 0; /* nothing to check when disabling or disabled */
+
+ if (!crtc_state || !crtc_state->enable)
+ /* nothing to check when disabling or disabled or no CRTC set */
+ return 0;
if (crtc_state->enable)
drm_mode_get_hv_timing(&crtc_state->mode,
--
2.7.4
On Tue, Feb 13, 2018 at 10:44:16AM +0200, Oleksandr Andrushchenko wrote:
> From: Oleksandr Andrushchenko <[email protected]>
>
> It is possible that drm_simple_kms_plane_atomic_check called
> with no CRTC set, e.g. when user-space application sets CRTC_ID/FB_ID
> to 0 before doing any actual drawing. This leads to NULL pointer
> dereference because in this case new CRTC state is NULL and must be
> checked before accessing.
>
> Signed-off-by: Oleksandr Andrushchenko <[email protected]>
> ---
> drivers/gpu/drm/drm_simple_kms_helper.c | 6 ++++--
> 1 file changed, 4 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/gpu/drm/drm_simple_kms_helper.c b/drivers/gpu/drm/drm_simple_kms_helper.c
> index 9ca8a4a59b74..a05eca9cec8b 100644
> --- a/drivers/gpu/drm/drm_simple_kms_helper.c
> +++ b/drivers/gpu/drm/drm_simple_kms_helper.c
> @@ -121,8 +121,10 @@ static int drm_simple_kms_plane_atomic_check(struct drm_plane *plane,
> pipe = container_of(plane, struct drm_simple_display_pipe, plane);
> crtc_state = drm_atomic_get_new_crtc_state(plane_state->state,
> &pipe->crtc);
> - if (!crtc_state->enable)
> - return 0; /* nothing to check when disabling or disabled */
> +
> + if (!crtc_state || !crtc_state->enable)
> + /* nothing to check when disabling or disabled or no CRTC set */
> + return 0;
>
> if (crtc_state->enable)
> drm_mode_get_hv_timing(&crtc_state->mode,
Hm, this is a bit annoying, since the can_position = false parameter to
drm_atomic_helper_check_plane_state is supposed to catch all this. Would
moving all the checks after the call to that helper, and gating them on
plane_state->visible also work?
We'd need to add a guarantee to drm_atomic_helper_check_plane_state that
it can cope with crtc_state == NULL, but I think that's a good idea
anyway. Atm it shouldn't end up looking at the crtc_state pointer in that
case.
Otherwise we'll just go with your fix, but it feels all a bit too fragile,
hence why I want to explore more robust options a bit.
-Daniel
--
Daniel Vetter
Software Engineer, Intel Corporation
http://blog.ffwll.ch
On 02/19/2018 04:30 PM, Daniel Vetter wrote:
> On Tue, Feb 13, 2018 at 10:44:16AM +0200, Oleksandr Andrushchenko wrote:
>> From: Oleksandr Andrushchenko <[email protected]>
>>
>> It is possible that drm_simple_kms_plane_atomic_check called
>> with no CRTC set, e.g. when user-space application sets CRTC_ID/FB_ID
>> to 0 before doing any actual drawing. This leads to NULL pointer
>> dereference because in this case new CRTC state is NULL and must be
>> checked before accessing.
>>
>> Signed-off-by: Oleksandr Andrushchenko <[email protected]>
>> ---
>> drivers/gpu/drm/drm_simple_kms_helper.c | 6 ++++--
>> 1 file changed, 4 insertions(+), 2 deletions(-)
>>
>> diff --git a/drivers/gpu/drm/drm_simple_kms_helper.c b/drivers/gpu/drm/drm_simple_kms_helper.c
>> index 9ca8a4a59b74..a05eca9cec8b 100644
>> --- a/drivers/gpu/drm/drm_simple_kms_helper.c
>> +++ b/drivers/gpu/drm/drm_simple_kms_helper.c
>> @@ -121,8 +121,10 @@ static int drm_simple_kms_plane_atomic_check(struct drm_plane *plane,
>> pipe = container_of(plane, struct drm_simple_display_pipe, plane);
>> crtc_state = drm_atomic_get_new_crtc_state(plane_state->state,
>> &pipe->crtc);
>> - if (!crtc_state->enable)
>> - return 0; /* nothing to check when disabling or disabled */
>> +
>> + if (!crtc_state || !crtc_state->enable)
>> + /* nothing to check when disabling or disabled or no CRTC set */
>> + return 0;
>>
>> if (crtc_state->enable)
>> drm_mode_get_hv_timing(&crtc_state->mode,
> Hm, this is a bit annoying, since the can_position = false parameter to
> drm_atomic_helper_check_plane_state is supposed to catch all this. Would
> moving all the checks after the call to that helper, and gating them on
> plane_state->visible also work?
Yes, it does work if this is what you mean:
diff --git a/drivers/gpu/drm/drm_simple_kms_helper.c
b/drivers/gpu/drm/drm_simple_kms_helper.c
index a05eca9cec8b..c48858bb2823 100644
--- a/drivers/gpu/drm/drm_simple_kms_helper.c
+++ b/drivers/gpu/drm/drm_simple_kms_helper.c
@@ -122,14 +122,6 @@ static int drm_simple_kms_plane_atomic_check(struct
drm_plane *plane,
crtc_state = drm_atomic_get_new_crtc_state(plane_state->state,
&pipe->crtc);
- if (!crtc_state || !crtc_state->enable)
- /* nothing to check when disabling or disabled or no
CRTC set */
- return 0;
-
- if (crtc_state->enable)
- drm_mode_get_hv_timing(&crtc_state->mode,
- &clip.x2, &clip.y2);
-
ret = drm_atomic_helper_check_plane_state(plane_state, crtc_state,
&clip,
DRM_PLANE_HELPER_NO_SCALING,
@@ -138,6 +130,13 @@ static int drm_simple_kms_plane_atomic_check(struct
drm_plane *plane,
if (ret)
return ret;
+ if (!plane_state->visible || !crtc_state->enable)
+ return 0; /* nothing to check when disabling or disabled */
+
+ if (plane_state->visible && crtc_state->enable)
+ drm_mode_get_hv_timing(&crtc_state->mode,
+ &clip.x2, &clip.y2);
+
if (!plane_state->visible)
return -EINVAL;
> We'd need to add a guarantee to drm_atomic_helper_check_plane_state that
> it can cope with crtc_state == NULL, but I think that's a good idea
> anyway. Atm it shouldn't end up looking at the crtc_state pointer in that
> case.
It doesn't look at it at the moment
> Otherwise we'll just go with your fix, but it feels all a bit too fragile,
> hence why I want to explore more robust options a bit.
At list with the change above it passes my test which failed
before. Although I cannot confirm it works for others, but it
certainly does for me.
> -Daniel
Do you want me to send v1 with the code above?
Thank you,
Oleksandr
On Mon, Feb 19, 2018 at 04:58:43PM +0200, Oleksandr Andrushchenko wrote:
> On 02/19/2018 04:30 PM, Daniel Vetter wrote:
> > On Tue, Feb 13, 2018 at 10:44:16AM +0200, Oleksandr Andrushchenko wrote:
> > > From: Oleksandr Andrushchenko <[email protected]>
> > >
> > > It is possible that drm_simple_kms_plane_atomic_check called
> > > with no CRTC set, e.g. when user-space application sets CRTC_ID/FB_ID
> > > to 0 before doing any actual drawing. This leads to NULL pointer
> > > dereference because in this case new CRTC state is NULL and must be
> > > checked before accessing.
> > >
> > > Signed-off-by: Oleksandr Andrushchenko <[email protected]>
> > > ---
> > > drivers/gpu/drm/drm_simple_kms_helper.c | 6 ++++--
> > > 1 file changed, 4 insertions(+), 2 deletions(-)
> > >
> > > diff --git a/drivers/gpu/drm/drm_simple_kms_helper.c b/drivers/gpu/drm/drm_simple_kms_helper.c
> > > index 9ca8a4a59b74..a05eca9cec8b 100644
> > > --- a/drivers/gpu/drm/drm_simple_kms_helper.c
> > > +++ b/drivers/gpu/drm/drm_simple_kms_helper.c
> > > @@ -121,8 +121,10 @@ static int drm_simple_kms_plane_atomic_check(struct drm_plane *plane,
> > > pipe = container_of(plane, struct drm_simple_display_pipe, plane);
> > > crtc_state = drm_atomic_get_new_crtc_state(plane_state->state,
> > > &pipe->crtc);
> > > - if (!crtc_state->enable)
> > > - return 0; /* nothing to check when disabling or disabled */
> > > +
> > > + if (!crtc_state || !crtc_state->enable)
> > > + /* nothing to check when disabling or disabled or no CRTC set */
> > > + return 0;
> > > if (crtc_state->enable)
> > > drm_mode_get_hv_timing(&crtc_state->mode,
> > Hm, this is a bit annoying, since the can_position = false parameter to
> > drm_atomic_helper_check_plane_state is supposed to catch all this. Would
> > moving all the checks after the call to that helper, and gating them on
> > plane_state->visible also work?
> Yes, it does work if this is what you mean:
I wasn't sure, thanks for figuring this out!
> diff --git a/drivers/gpu/drm/drm_simple_kms_helper.c
> b/drivers/gpu/drm/drm_simple_kms_helper.c
> index a05eca9cec8b..c48858bb2823 100644
> --- a/drivers/gpu/drm/drm_simple_kms_helper.c
> +++ b/drivers/gpu/drm/drm_simple_kms_helper.c
> @@ -122,14 +122,6 @@ static int drm_simple_kms_plane_atomic_check(struct
> drm_plane *plane,
> ??????? crtc_state = drm_atomic_get_new_crtc_state(plane_state->state,
> &pipe->crtc);
>
> -?????? if (!crtc_state || !crtc_state->enable)
> -?????????????? /* nothing to check when disabling or disabled or no CRTC
> set */
> -?????????????? return 0;
> -
> -?????? if (crtc_state->enable)
> -?????????????? drm_mode_get_hv_timing(&crtc_state->mode,
> -????????????????????????????????????? &clip.x2, &clip.y2);
> -
> ??????? ret = drm_atomic_helper_check_plane_state(plane_state, crtc_state,
> ????????????????????????????????????????????????? &clip,
> DRM_PLANE_HELPER_NO_SCALING,
> @@ -138,6 +130,13 @@ static int drm_simple_kms_plane_atomic_check(struct
> drm_plane *plane,
> ??????? if (ret)
> ??????????????? return ret;
>
> +?????? if (!plane_state->visible || !crtc_state->enable)
> +?????????????? return 0; /* nothing to check when disabling or disabled */
if (!plane_state->visible) {
WARN_ON(crtc_state->enabled);
return 0;
}
The helper call above should guarantee this.
> +
> +?????? if (plane_state->visible && crtc_state->enable)
Similar here.
> +?????????????? drm_mode_get_hv_timing(&crtc_state->mode,
> +????????????????????????????????????? &clip.x2, &clip.y2);
> +
> ??????? if (!plane_state->visible)
> ??????????????? return -EINVAL;
This can now be removed, the plane helper takes care of checking for
plane_state->visible != crtc_state->enable. Please also remove.
> > We'd need to add a guarantee to drm_atomic_helper_check_plane_state that
> > it can cope with crtc_state == NULL, but I think that's a good idea
> > anyway. Atm it shouldn't end up looking at the crtc_state pointer in that
> > case.
> It doesn't look at it at the moment
> > Otherwise we'll just go with your fix, but it feels all a bit too fragile,
> > hence why I want to explore more robust options a bit.
> At list with the change above it passes my test which failed
> before. Although I cannot confirm it works for others, but it
> certainly does for me.
> > -Daniel
> Do you want me to send v1 with the code above?
Yes please, with my above cleanup suggestions.
Thanks, Daniel
--
Daniel Vetter
Software Engineer, Intel Corporation
http://blog.ffwll.ch
On 02/20/2018 01:17 PM, Daniel Vetter wrote:
> On Mon, Feb 19, 2018 at 04:58:43PM +0200, Oleksandr Andrushchenko wrote:
>> On 02/19/2018 04:30 PM, Daniel Vetter wrote:
>>> On Tue, Feb 13, 2018 at 10:44:16AM +0200, Oleksandr Andrushchenko wrote:
>>>> From: Oleksandr Andrushchenko <[email protected]>
>>>>
>>>> It is possible that drm_simple_kms_plane_atomic_check called
>>>> with no CRTC set, e.g. when user-space application sets CRTC_ID/FB_ID
>>>> to 0 before doing any actual drawing. This leads to NULL pointer
>>>> dereference because in this case new CRTC state is NULL and must be
>>>> checked before accessing.
>>>>
>>>> Signed-off-by: Oleksandr Andrushchenko <[email protected]>
>>>> ---
>>>> drivers/gpu/drm/drm_simple_kms_helper.c | 6 ++++--
>>>> 1 file changed, 4 insertions(+), 2 deletions(-)
>>>>
>>>> diff --git a/drivers/gpu/drm/drm_simple_kms_helper.c b/drivers/gpu/drm/drm_simple_kms_helper.c
>>>> index 9ca8a4a59b74..a05eca9cec8b 100644
>>>> --- a/drivers/gpu/drm/drm_simple_kms_helper.c
>>>> +++ b/drivers/gpu/drm/drm_simple_kms_helper.c
>>>> @@ -121,8 +121,10 @@ static int drm_simple_kms_plane_atomic_check(struct drm_plane *plane,
>>>> pipe = container_of(plane, struct drm_simple_display_pipe, plane);
>>>> crtc_state = drm_atomic_get_new_crtc_state(plane_state->state,
>>>> &pipe->crtc);
>>>> - if (!crtc_state->enable)
>>>> - return 0; /* nothing to check when disabling or disabled */
>>>> +
>>>> + if (!crtc_state || !crtc_state->enable)
>>>> + /* nothing to check when disabling or disabled or no CRTC set */
>>>> + return 0;
>>>> if (crtc_state->enable)
>>>> drm_mode_get_hv_timing(&crtc_state->mode,
>>> Hm, this is a bit annoying, since the can_position = false parameter to
>>> drm_atomic_helper_check_plane_state is supposed to catch all this. Would
>>> moving all the checks after the call to that helper, and gating them on
>>> plane_state->visible also work?
>> Yes, it does work if this is what you mean:
> I wasn't sure, thanks for figuring this out!
>
>> diff --git a/drivers/gpu/drm/drm_simple_kms_helper.c
>> b/drivers/gpu/drm/drm_simple_kms_helper.c
>> index a05eca9cec8b..c48858bb2823 100644
>> --- a/drivers/gpu/drm/drm_simple_kms_helper.c
>> +++ b/drivers/gpu/drm/drm_simple_kms_helper.c
>> @@ -122,14 +122,6 @@ static int drm_simple_kms_plane_atomic_check(struct
>> drm_plane *plane,
>> crtc_state = drm_atomic_get_new_crtc_state(plane_state->state,
>> &pipe->crtc);
>>
>> - if (!crtc_state || !crtc_state->enable)
>> - /* nothing to check when disabling or disabled or no CRTC
>> set */
>> - return 0;
>> -
>> - if (crtc_state->enable)
>> - drm_mode_get_hv_timing(&crtc_state->mode,
>> - &clip.x2, &clip.y2);
>> -
>> ret = drm_atomic_helper_check_plane_state(plane_state, crtc_state,
>> &clip,
>> DRM_PLANE_HELPER_NO_SCALING,
>> @@ -138,6 +130,13 @@ static int drm_simple_kms_plane_atomic_check(struct
>> drm_plane *plane,
>> if (ret)
>> return ret;
>>
>> + if (!plane_state->visible || !crtc_state->enable)
>> + return 0; /* nothing to check when disabling or disabled */
> if (!plane_state->visible) {
> WARN_ON(crtc_state->enabled);
> return 0;
> }
>
> The helper call above should guarantee this.
Yes, but I still see cases when crtc_state is NULL, thus
making crtc_state->enable to fail
>> +
>> + if (plane_state->visible && crtc_state->enable)
> Similar here.
>
>> + drm_mode_get_hv_timing(&crtc_state->mode,
>> + &clip.x2, &clip.y2);
>> +
>> if (!plane_state->visible)
>> return -EINVAL;
> This can now be removed, the plane helper takes care of checking for
> plane_state->visible != crtc_state->enable. Please also remove.
>
>>> We'd need to add a guarantee to drm_atomic_helper_check_plane_state that
>>> it can cope with crtc_state == NULL, but I think that's a good idea
>>> anyway. Atm it shouldn't end up looking at the crtc_state pointer in that
>>> case.
>> It doesn't look at it at the moment
>>> Otherwise we'll just go with your fix, but it feels all a bit too fragile,
>>> hence why I want to explore more robust options a bit.
>> At list with the change above it passes my test which failed
>> before. Although I cannot confirm it works for others, but it
>> certainly does for me.
>>> -Daniel
>> Do you want me to send v1 with the code above?
> Yes please, with my above cleanup suggestions.
Please see the patch under test attached (I believe it is what you mean,
with the only change that
if (!plane_state->visible) {
*if (crtc_state)*
WARN_ON(crtc_state->enable);
return 0;
}
check is used).
Whith this patch + additional logs I have:
[ 18.939204] [drm:drm_ioctl [drm]] pid=2105, dev=0xe200, auth=1,
DRM_IOCTL_MODE_ATOMIC
[...]
[ 18.939681] [drm:drm_atomic_set_crtc_for_plane [drm]] Link plane
state 00000000c302cbbf to [NOCRTC]
[ 18.939822] [drm:drm_atomic_set_fb_for_plane [drm]] Set [NOFB] for
plane state 00000000c302cbbf
[ 18.939963] [drm:drm_atomic_print_state [drm]] checking 000000000bc224e7
[ 18.939988] vdispl vdispl.0: [drm] plane[29]: plane-0
[ 18.940003] vdispl vdispl.0: [drm] crtc=(null)
[ 18.940018] vdispl vdispl.0: [drm] fb=0
[ 18.940032] vdispl vdispl.0: [drm] crtc-pos=0x0+0+0
[ 18.940048] vdispl vdispl.0: [drm]
src-pos=0.000000x0.000000+0.000000+0.000000
[ 18.940067] vdispl vdispl.0: [drm] rotation=1
[ 18.940199] [drm:drm_atomic_check_only [drm]] checking 000000000bc224e7
[ 18.940226] ================================= plane_state->visible 0
crtc_state (null)
[...]
[ 18.978146] [drm:drm_atomic_set_crtc_for_plane [drm]] Link plane
state 000000006bd50580 to [CRTC:30:crtc-0]
[ 18.978292] [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:35] for
plane state 000000006bd50580
[ 18.978993] [drm:drm_atomic_set_mode_prop_for_crtc [drm]] Set
[MODE:1024x768] for CRTC state 00000000e5a28f6a
[ 18.979425] [drm:drm_atomic_check_only [drm]] checking 000000000bc224e7
[ 18.979540] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]]
[CRTC:30:crtc-0] mode changed
[ 18.979632] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]]
[CRTC:30:crtc-0] enable changed
[ 18.979708] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]]
[CRTC:30:crtc-0] active changed
[ 18.979792] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]]
Updating routing for [CONNECTOR:28:Virtual-1]
[ 18.979877] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]]
[CONNECTOR:28:Virtual-1] using [ENCODER:31:None-31] on [CRTC:30:crtc-0]
[ 18.979960] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]]
[CRTC:30:crtc-0] needs all connectors, enable: y, active: y
[ 18.980139] [drm:drm_atomic_add_affected_connectors [drm]] Adding all
current connectors for [CRTC:30:crtc-0] to 000000000bc224e7
[ 18.980184] ================================= plane_state->visible 0
crtc_state 00000000e5a28f6a
[ 18.980205] crtc_state->enable 1
*[ 19.022608] WARNING: CPU: 1 PID: 2105 at
drivers/gpu/drm/drm_simple_kms_helper.c:137
drm_simple_kms_plane_atomic_check+0xdc/0xf8 [drm_kms_helper]*
[...]
[ 19.113601] ================================= plane_state->visible 0
crtc_state 00000000e5a28f6a
[ 19.113623] crtc_state->enable 1
[ 19.113792] WARNING: CPU: 1 PID: 2105 at
drivers/gpu/drm/drm_simple_kms_helper.c:137
drm_simple_kms_plane_atomic_check+0xdc/0xf8 [drm_kms_helper]
[...]
And finally
[ 19.340249] ================================= plane_state->visible 0
crtc_state 0000000036a1b1f5
[ 19.340271] crtc_state->enable 0
So, it seems that crtc_state can still be NULL if
"!plane_state->visible" making
NULL pointer dereference, so we need a check for that.
Yet, !plane_state->visible && crtc_state->enable makes WARN_ON to fire
always. So, probably we may want removing it.
>
> Thanks, Daniel
Thank you,
Oleksandr
On Tue, Feb 20, 2018 at 02:36:05PM +0200, Oleksandr Andrushchenko wrote:
> On 02/20/2018 01:17 PM, Daniel Vetter wrote:
> > On Mon, Feb 19, 2018 at 04:58:43PM +0200, Oleksandr Andrushchenko wrote:
> > > On 02/19/2018 04:30 PM, Daniel Vetter wrote:
> > > > On Tue, Feb 13, 2018 at 10:44:16AM +0200, Oleksandr Andrushchenko wrote:
> > > > > From: Oleksandr Andrushchenko <[email protected]>
> > > > >
> > > > > It is possible that drm_simple_kms_plane_atomic_check called
> > > > > with no CRTC set, e.g. when user-space application sets CRTC_ID/FB_ID
> > > > > to 0 before doing any actual drawing. This leads to NULL pointer
> > > > > dereference because in this case new CRTC state is NULL and must be
> > > > > checked before accessing.
> > > > >
> > > > > Signed-off-by: Oleksandr Andrushchenko <[email protected]>
> > > > > ---
> > > > > drivers/gpu/drm/drm_simple_kms_helper.c | 6 ++++--
> > > > > 1 file changed, 4 insertions(+), 2 deletions(-)
> > > > >
> > > > > diff --git a/drivers/gpu/drm/drm_simple_kms_helper.c b/drivers/gpu/drm/drm_simple_kms_helper.c
> > > > > index 9ca8a4a59b74..a05eca9cec8b 100644
> > > > > --- a/drivers/gpu/drm/drm_simple_kms_helper.c
> > > > > +++ b/drivers/gpu/drm/drm_simple_kms_helper.c
> > > > > @@ -121,8 +121,10 @@ static int drm_simple_kms_plane_atomic_check(struct drm_plane *plane,
> > > > > pipe = container_of(plane, struct drm_simple_display_pipe, plane);
> > > > > crtc_state = drm_atomic_get_new_crtc_state(plane_state->state,
> > > > > &pipe->crtc);
> > > > > - if (!crtc_state->enable)
> > > > > - return 0; /* nothing to check when disabling or disabled */
> > > > > +
> > > > > + if (!crtc_state || !crtc_state->enable)
> > > > > + /* nothing to check when disabling or disabled or no CRTC set */
> > > > > + return 0;
> > > > > if (crtc_state->enable)
> > > > > drm_mode_get_hv_timing(&crtc_state->mode,
> > > > Hm, this is a bit annoying, since the can_position = false parameter to
> > > > drm_atomic_helper_check_plane_state is supposed to catch all this. Would
> > > > moving all the checks after the call to that helper, and gating them on
> > > > plane_state->visible also work?
> > > Yes, it does work if this is what you mean:
> > I wasn't sure, thanks for figuring this out!
> >
> > > diff --git a/drivers/gpu/drm/drm_simple_kms_helper.c
> > > b/drivers/gpu/drm/drm_simple_kms_helper.c
> > > index a05eca9cec8b..c48858bb2823 100644
> > > --- a/drivers/gpu/drm/drm_simple_kms_helper.c
> > > +++ b/drivers/gpu/drm/drm_simple_kms_helper.c
> > > @@ -122,14 +122,6 @@ static int drm_simple_kms_plane_atomic_check(struct
> > > drm_plane *plane,
> > > ??????? crtc_state = drm_atomic_get_new_crtc_state(plane_state->state,
> > > &pipe->crtc);
> > >
> > > -?????? if (!crtc_state || !crtc_state->enable)
> > > -?????????????? /* nothing to check when disabling or disabled or no CRTC
> > > set */
> > > -?????????????? return 0;
> > > -
> > > -?????? if (crtc_state->enable)
> > > -?????????????? drm_mode_get_hv_timing(&crtc_state->mode,
> > > -????????????????????????????????????? &clip.x2, &clip.y2);
> > > -
> > > ??????? ret = drm_atomic_helper_check_plane_state(plane_state, crtc_state,
> > > ????????????????????????????????????????????????? &clip,
> > > DRM_PLANE_HELPER_NO_SCALING,
> > > @@ -138,6 +130,13 @@ static int drm_simple_kms_plane_atomic_check(struct
> > > drm_plane *plane,
> > > ??????? if (ret)
> > > ??????????????? return ret;
> > >
> > > +?????? if (!plane_state->visible || !crtc_state->enable)
> > > +?????????????? return 0; /* nothing to check when disabling or disabled */
> > if (!plane_state->visible) {
> > WARN_ON(crtc_state->enabled);
> > return 0;
> > }
> >
> > The helper call above should guarantee this.
> Yes, but I still see cases when crtc_state is NULL, thus
> making crtc_state->enable to fail
Right, when the plane is completely off there's no CRTC state. Correct
check should be
WARN_ON(crtc_state && crtc_state->enabled);
> > > +
> > > +?????? if (plane_state->visible && crtc_state->enable)
> > Similar here.
> >
> > > +?????????????? drm_mode_get_hv_timing(&crtc_state->mode,
> > > +????????????????????????????????????? &clip.x2, &clip.y2);
> > > +
> > > ??????? if (!plane_state->visible)
> > > ??????????????? return -EINVAL;
> > This can now be removed, the plane helper takes care of checking for
> > plane_state->visible != crtc_state->enable. Please also remove.
> >
> > > > We'd need to add a guarantee to drm_atomic_helper_check_plane_state that
> > > > it can cope with crtc_state == NULL, but I think that's a good idea
> > > > anyway. Atm it shouldn't end up looking at the crtc_state pointer in that
> > > > case.
> > > It doesn't look at it at the moment
> > > > Otherwise we'll just go with your fix, but it feels all a bit too fragile,
> > > > hence why I want to explore more robust options a bit.
> > > At list with the change above it passes my test which failed
> > > before. Although I cannot confirm it works for others, but it
> > > certainly does for me.
> > > > -Daniel
> > > Do you want me to send v1 with the code above?
> > Yes please, with my above cleanup suggestions.
> Please see the patch under test attached (I believe it is what you mean,
> with the only change that
> ??? if (!plane_state->visible) {
> ??? ??? *if (crtc_state)*
> ??? ??? ??? WARN_ON(crtc_state->enable);
> ??? ??? return 0;
> ??? }
> check is used).
>
> Whith this patch + additional logs I have:
>
> [?? 18.939204] [drm:drm_ioctl [drm]] pid=2105, dev=0xe200, auth=1,
> DRM_IOCTL_MODE_ATOMIC
> [...]
> [?? 18.939681] [drm:drm_atomic_set_crtc_for_plane [drm]] Link plane state
> 00000000c302cbbf to [NOCRTC]
> [?? 18.939822] [drm:drm_atomic_set_fb_for_plane [drm]] Set [NOFB] for plane
> state 00000000c302cbbf
> [?? 18.939963] [drm:drm_atomic_print_state [drm]] checking 000000000bc224e7
> [?? 18.939988] vdispl vdispl.0: [drm] plane[29]: plane-0
> [?? 18.940003] vdispl vdispl.0: [drm]?? crtc=(null)
> [?? 18.940018] vdispl vdispl.0: [drm]?? fb=0
> [?? 18.940032] vdispl vdispl.0: [drm]?? crtc-pos=0x0+0+0
> [?? 18.940048] vdispl vdispl.0: [drm]
> src-pos=0.000000x0.000000+0.000000+0.000000
> [?? 18.940067] vdispl vdispl.0: [drm]?? rotation=1
> [?? 18.940199] [drm:drm_atomic_check_only [drm]] checking 000000000bc224e7
> [?? 18.940226] ================================= plane_state->visible 0
> crtc_state?????????? (null)
> [...]
> [?? 18.978146] [drm:drm_atomic_set_crtc_for_plane [drm]] Link plane state
> 000000006bd50580 to [CRTC:30:crtc-0]
> [?? 18.978292] [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:35] for plane
> state 000000006bd50580
> [?? 18.978993] [drm:drm_atomic_set_mode_prop_for_crtc [drm]] Set
> [MODE:1024x768] for CRTC state 00000000e5a28f6a
> [?? 18.979425] [drm:drm_atomic_check_only [drm]] checking 000000000bc224e7
> [?? 18.979540] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]]
> [CRTC:30:crtc-0] mode changed
> [?? 18.979632] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]]
> [CRTC:30:crtc-0] enable changed
> [?? 18.979708] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]]
> [CRTC:30:crtc-0] active changed
> [?? 18.979792] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]]
> Updating routing for [CONNECTOR:28:Virtual-1]
> [?? 18.979877] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]]
> [CONNECTOR:28:Virtual-1] using [ENCODER:31:None-31] on [CRTC:30:crtc-0]
> [?? 18.979960] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]]
> [CRTC:30:crtc-0] needs all connectors, enable: y, active: y
> [?? 18.980139] [drm:drm_atomic_add_affected_connectors [drm]] Adding all
> current connectors for [CRTC:30:crtc-0] to 000000000bc224e7
> [?? 18.980184] ================================= plane_state->visible 0
> crtc_state 00000000e5a28f6a
> [?? 18.980205] crtc_state->enable 1
>
> *[?? 19.022608] WARNING: CPU: 1 PID: 2105 at
> drivers/gpu/drm/drm_simple_kms_helper.c:137
> drm_simple_kms_plane_atomic_check+0xdc/0xf8 [drm_kms_helper]*
>
> [...]
>
> [?? 19.113601] ================================= plane_state->visible 0
> crtc_state 00000000e5a28f6a
> [?? 19.113623] crtc_state->enable 1
> [?? 19.113792] WARNING: CPU: 1 PID: 2105 at
> drivers/gpu/drm/drm_simple_kms_helper.c:137
> drm_simple_kms_plane_atomic_check+0xdc/0xf8 [drm_kms_helper]
>
> [...]
>
> And finally
>
> [?? 19.340249] ================================= plane_state->visible 0
> crtc_state 0000000036a1b1f5
> [?? 19.340271] crtc_state->enable 0
>
> So, it seems that crtc_state can still be NULL if "!plane_state->visible"
> making
> NULL pointer dereference, so we need a check for that.
> Yet, !plane_state->visible && crtc_state->enable makes WARN_ON to fire
> always. So, probably we may want removing it.
> >
> > Thanks, Daniel
> Thank you,
> Oleksandr
> From dbcce708b237740158a2c16029c56a579324f269 Mon Sep 17 00:00:00 2001
> From: Oleksandr Andrushchenko <[email protected]>
> Date: Tue, 13 Feb 2018 10:32:20 +0200
> Subject: [PATCH] drm/simple_kms_helper: Fix NULL pointer dereference with no
> active CRTC
>
> It is possible that drm_simple_kms_plane_atomic_check called
> with no CRTC set, e.g. when user-space application sets CRTC_ID/FB_ID
> to 0 before doing any actual drawing. This leads to NULL pointer
> dereference because in this case new CRTC state is NULL and must be
> checked before accessing.
>
> Signed-off-by: Oleksandr Andrushchenko <[email protected]>
> ---
> drivers/gpu/drm/drm_simple_kms_helper.c | 15 +++++++--------
> 1 file changed, 7 insertions(+), 8 deletions(-)
>
> diff --git a/drivers/gpu/drm/drm_simple_kms_helper.c b/drivers/gpu/drm/drm_simple_kms_helper.c
> index 9ca8a4a59b74..f54711ff9767 100644
> --- a/drivers/gpu/drm/drm_simple_kms_helper.c
> +++ b/drivers/gpu/drm/drm_simple_kms_helper.c
> @@ -121,12 +121,6 @@ static int drm_simple_kms_plane_atomic_check(struct drm_plane *plane,
> pipe = container_of(plane, struct drm_simple_display_pipe, plane);
> crtc_state = drm_atomic_get_new_crtc_state(plane_state->state,
> &pipe->crtc);
> - if (!crtc_state->enable)
> - return 0; /* nothing to check when disabling or disabled */
> -
> - if (crtc_state->enable)
> - drm_mode_get_hv_timing(&crtc_state->mode,
> - &clip.x2, &clip.y2);
>
> ret = drm_atomic_helper_check_plane_state(plane_state, crtc_state,
> &clip,
> @@ -136,8 +130,13 @@ static int drm_simple_kms_plane_atomic_check(struct drm_plane *plane,
> if (ret)
> return ret;
>
> - if (!plane_state->visible)
> - return -EINVAL;
> + if (!plane_state->visible) {
> + if (crtc_state)
> + WARN_ON(crtc_state->enable);
> + return 0;
> + }
> +
> + drm_mode_get_hv_timing(&crtc_state->mode, &clip.x2, &clip.y2);
lgtm. With or without the bikeshed to pull the crtc_state check into the
WARN_ON.
Reviewed-by: Daniel Vetter <[email protected]>
Please resubmit as a stand-alone patch, patchwork can't pull patches out
of attachments :-/
-Daniel
>
> if (!pipe->funcs || !pipe->funcs->check)
> return 0;
> --
> 2.7.4
>
> _______________________________________________
> dri-devel mailing list
> [email protected]
> https://lists.freedesktop.org/mailman/listinfo/dri-devel
--
Daniel Vetter
Software Engineer, Intel Corporation
http://blog.ffwll.ch
On 02/20/2018 02:49 PM, Daniel Vetter wrote:
> On Tue, Feb 20, 2018 at 02:36:05PM +0200, Oleksandr Andrushchenko wrote:
>> On 02/20/2018 01:17 PM, Daniel Vetter wrote:
>>> On Mon, Feb 19, 2018 at 04:58:43PM +0200, Oleksandr Andrushchenko wrote:
>>>> On 02/19/2018 04:30 PM, Daniel Vetter wrote:
>>>>> On Tue, Feb 13, 2018 at 10:44:16AM +0200, Oleksandr Andrushchenko wrote:
>>>>>> From: Oleksandr Andrushchenko <[email protected]>
>>>>>>
>>>>>> It is possible that drm_simple_kms_plane_atomic_check called
>>>>>> with no CRTC set, e.g. when user-space application sets CRTC_ID/FB_ID
>>>>>> to 0 before doing any actual drawing. This leads to NULL pointer
>>>>>> dereference because in this case new CRTC state is NULL and must be
>>>>>> checked before accessing.
>>>>>>
>>>>>> Signed-off-by: Oleksandr Andrushchenko <[email protected]>
>>>>>> ---
>>>>>> drivers/gpu/drm/drm_simple_kms_helper.c | 6 ++++--
>>>>>> 1 file changed, 4 insertions(+), 2 deletions(-)
>>>>>>
>>>>>> diff --git a/drivers/gpu/drm/drm_simple_kms_helper.c b/drivers/gpu/drm/drm_simple_kms_helper.c
>>>>>> index 9ca8a4a59b74..a05eca9cec8b 100644
>>>>>> --- a/drivers/gpu/drm/drm_simple_kms_helper.c
>>>>>> +++ b/drivers/gpu/drm/drm_simple_kms_helper.c
>>>>>> @@ -121,8 +121,10 @@ static int drm_simple_kms_plane_atomic_check(struct drm_plane *plane,
>>>>>> pipe = container_of(plane, struct drm_simple_display_pipe, plane);
>>>>>> crtc_state = drm_atomic_get_new_crtc_state(plane_state->state,
>>>>>> &pipe->crtc);
>>>>>> - if (!crtc_state->enable)
>>>>>> - return 0; /* nothing to check when disabling or disabled */
>>>>>> +
>>>>>> + if (!crtc_state || !crtc_state->enable)
>>>>>> + /* nothing to check when disabling or disabled or no CRTC set */
>>>>>> + return 0;
>>>>>> if (crtc_state->enable)
>>>>>> drm_mode_get_hv_timing(&crtc_state->mode,
>>>>> Hm, this is a bit annoying, since the can_position = false parameter to
>>>>> drm_atomic_helper_check_plane_state is supposed to catch all this. Would
>>>>> moving all the checks after the call to that helper, and gating them on
>>>>> plane_state->visible also work?
>>>> Yes, it does work if this is what you mean:
>>> I wasn't sure, thanks for figuring this out!
>>>
>>>> diff --git a/drivers/gpu/drm/drm_simple_kms_helper.c
>>>> b/drivers/gpu/drm/drm_simple_kms_helper.c
>>>> index a05eca9cec8b..c48858bb2823 100644
>>>> --- a/drivers/gpu/drm/drm_simple_kms_helper.c
>>>> +++ b/drivers/gpu/drm/drm_simple_kms_helper.c
>>>> @@ -122,14 +122,6 @@ static int drm_simple_kms_plane_atomic_check(struct
>>>> drm_plane *plane,
>>>> crtc_state = drm_atomic_get_new_crtc_state(plane_state->state,
>>>> &pipe->crtc);
>>>>
>>>> - if (!crtc_state || !crtc_state->enable)
>>>> - /* nothing to check when disabling or disabled or no CRTC
>>>> set */
>>>> - return 0;
>>>> -
>>>> - if (crtc_state->enable)
>>>> - drm_mode_get_hv_timing(&crtc_state->mode,
>>>> - &clip.x2, &clip.y2);
>>>> -
>>>> ret = drm_atomic_helper_check_plane_state(plane_state, crtc_state,
>>>> &clip,
>>>> DRM_PLANE_HELPER_NO_SCALING,
>>>> @@ -138,6 +130,13 @@ static int drm_simple_kms_plane_atomic_check(struct
>>>> drm_plane *plane,
>>>> if (ret)
>>>> return ret;
>>>>
>>>> + if (!plane_state->visible || !crtc_state->enable)
>>>> + return 0; /* nothing to check when disabling or disabled */
>>> if (!plane_state->visible) {
>>> WARN_ON(crtc_state->enabled);
>>> return 0;
>>> }
>>>
>>> The helper call above should guarantee this.
>> Yes, but I still see cases when crtc_state is NULL, thus
>> making crtc_state->enable to fail
> Right, when the plane is completely off there's no CRTC state. Correct
> check should be
>
> WARN_ON(crtc_state && crtc_state->enabled);
ok, will update with this additional check
>
>>>> +
>>>> + if (plane_state->visible && crtc_state->enable)
>>> Similar here.
>>>
>>>> + drm_mode_get_hv_timing(&crtc_state->mode,
>>>> + &clip.x2, &clip.y2);
>>>> +
>>>> if (!plane_state->visible)
>>>> return -EINVAL;
>>> This can now be removed, the plane helper takes care of checking for
>>> plane_state->visible != crtc_state->enable. Please also remove.
>>>
>>>>> We'd need to add a guarantee to drm_atomic_helper_check_plane_state that
>>>>> it can cope with crtc_state == NULL, but I think that's a good idea
>>>>> anyway. Atm it shouldn't end up looking at the crtc_state pointer in that
>>>>> case.
>>>> It doesn't look at it at the moment
>>>>> Otherwise we'll just go with your fix, but it feels all a bit too fragile,
>>>>> hence why I want to explore more robust options a bit.
>>>> At list with the change above it passes my test which failed
>>>> before. Although I cannot confirm it works for others, but it
>>>> certainly does for me.
>>>>> -Daniel
>>>> Do you want me to send v1 with the code above?
>>> Yes please, with my above cleanup suggestions.
>> Please see the patch under test attached (I believe it is what you mean,
>> with the only change that
>> if (!plane_state->visible) {
>> *if (crtc_state)*
>> WARN_ON(crtc_state->enable);
>> return 0;
>> }
>> check is used).
>>
>> Whith this patch + additional logs I have:
>>
>> [ 18.939204] [drm:drm_ioctl [drm]] pid=2105, dev=0xe200, auth=1,
>> DRM_IOCTL_MODE_ATOMIC
>> [...]
>> [ 18.939681] [drm:drm_atomic_set_crtc_for_plane [drm]] Link plane state
>> 00000000c302cbbf to [NOCRTC]
>> [ 18.939822] [drm:drm_atomic_set_fb_for_plane [drm]] Set [NOFB] for plane
>> state 00000000c302cbbf
>> [ 18.939963] [drm:drm_atomic_print_state [drm]] checking 000000000bc224e7
>> [ 18.939988] vdispl vdispl.0: [drm] plane[29]: plane-0
>> [ 18.940003] vdispl vdispl.0: [drm] crtc=(null)
>> [ 18.940018] vdispl vdispl.0: [drm] fb=0
>> [ 18.940032] vdispl vdispl.0: [drm] crtc-pos=0x0+0+0
>> [ 18.940048] vdispl vdispl.0: [drm]
>> src-pos=0.000000x0.000000+0.000000+0.000000
>> [ 18.940067] vdispl vdispl.0: [drm] rotation=1
>> [ 18.940199] [drm:drm_atomic_check_only [drm]] checking 000000000bc224e7
>> [ 18.940226] ================================= plane_state->visible 0
>> crtc_state (null)
>> [...]
>> [ 18.978146] [drm:drm_atomic_set_crtc_for_plane [drm]] Link plane state
>> 000000006bd50580 to [CRTC:30:crtc-0]
>> [ 18.978292] [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:35] for plane
>> state 000000006bd50580
>> [ 18.978993] [drm:drm_atomic_set_mode_prop_for_crtc [drm]] Set
>> [MODE:1024x768] for CRTC state 00000000e5a28f6a
>> [ 18.979425] [drm:drm_atomic_check_only [drm]] checking 000000000bc224e7
>> [ 18.979540] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]]
>> [CRTC:30:crtc-0] mode changed
>> [ 18.979632] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]]
>> [CRTC:30:crtc-0] enable changed
>> [ 18.979708] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]]
>> [CRTC:30:crtc-0] active changed
>> [ 18.979792] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]]
>> Updating routing for [CONNECTOR:28:Virtual-1]
>> [ 18.979877] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]]
>> [CONNECTOR:28:Virtual-1] using [ENCODER:31:None-31] on [CRTC:30:crtc-0]
>> [ 18.979960] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]]
>> [CRTC:30:crtc-0] needs all connectors, enable: y, active: y
>> [ 18.980139] [drm:drm_atomic_add_affected_connectors [drm]] Adding all
>> current connectors for [CRTC:30:crtc-0] to 000000000bc224e7
>> [ 18.980184] ================================= plane_state->visible 0
>> crtc_state 00000000e5a28f6a
>> [ 18.980205] crtc_state->enable 1
>>
>> *[ 19.022608] WARNING: CPU: 1 PID: 2105 at
>> drivers/gpu/drm/drm_simple_kms_helper.c:137
>> drm_simple_kms_plane_atomic_check+0xdc/0xf8 [drm_kms_helper]*
>>
>> [...]
>>
>> [ 19.113601] ================================= plane_state->visible 0
>> crtc_state 00000000e5a28f6a
>> [ 19.113623] crtc_state->enable 1
>> [ 19.113792] WARNING: CPU: 1 PID: 2105 at
>> drivers/gpu/drm/drm_simple_kms_helper.c:137
>> drm_simple_kms_plane_atomic_check+0xdc/0xf8 [drm_kms_helper]
>>
>> [...]
>>
>> And finally
>>
>> [ 19.340249] ================================= plane_state->visible 0
>> crtc_state 0000000036a1b1f5
>> [ 19.340271] crtc_state->enable 0
>>
>> So, it seems that crtc_state can still be NULL if "!plane_state->visible"
>> making
>> NULL pointer dereference, so we need a check for that.
>> Yet, !plane_state->visible && crtc_state->enable makes WARN_ON to fire
>> always. So, probably we may want removing it.
>>> Thanks, Daniel
>> Thank you,
>> Oleksandr
>> From dbcce708b237740158a2c16029c56a579324f269 Mon Sep 17 00:00:00 2001
>> From: Oleksandr Andrushchenko <[email protected]>
>> Date: Tue, 13 Feb 2018 10:32:20 +0200
>> Subject: [PATCH] drm/simple_kms_helper: Fix NULL pointer dereference with no
>> active CRTC
>>
>> It is possible that drm_simple_kms_plane_atomic_check called
>> with no CRTC set, e.g. when user-space application sets CRTC_ID/FB_ID
>> to 0 before doing any actual drawing. This leads to NULL pointer
>> dereference because in this case new CRTC state is NULL and must be
>> checked before accessing.
>>
>> Signed-off-by: Oleksandr Andrushchenko <[email protected]>
>> ---
>> drivers/gpu/drm/drm_simple_kms_helper.c | 15 +++++++--------
>> 1 file changed, 7 insertions(+), 8 deletions(-)
>>
>> diff --git a/drivers/gpu/drm/drm_simple_kms_helper.c b/drivers/gpu/drm/drm_simple_kms_helper.c
>> index 9ca8a4a59b74..f54711ff9767 100644
>> --- a/drivers/gpu/drm/drm_simple_kms_helper.c
>> +++ b/drivers/gpu/drm/drm_simple_kms_helper.c
>> @@ -121,12 +121,6 @@ static int drm_simple_kms_plane_atomic_check(struct drm_plane *plane,
>> pipe = container_of(plane, struct drm_simple_display_pipe, plane);
>> crtc_state = drm_atomic_get_new_crtc_state(plane_state->state,
>> &pipe->crtc);
>> - if (!crtc_state->enable)
>> - return 0; /* nothing to check when disabling or disabled */
>> -
>> - if (crtc_state->enable)
>> - drm_mode_get_hv_timing(&crtc_state->mode,
>> - &clip.x2, &clip.y2);
>>
>> ret = drm_atomic_helper_check_plane_state(plane_state, crtc_state,
>> &clip,
>> @@ -136,8 +130,13 @@ static int drm_simple_kms_plane_atomic_check(struct drm_plane *plane,
>> if (ret)
>> return ret;
>>
>> - if (!plane_state->visible)
>> - return -EINVAL;
>> + if (!plane_state->visible) {
>> + if (crtc_state)
>> + WARN_ON(crtc_state->enable);
>> + return 0;
>> + }
>> +
>> + drm_mode_get_hv_timing(&crtc_state->mode, &clip.x2, &clip.y2);
> lgtm. With or without the bikeshed to pull the crtc_state check into the
> WARN_ON.
>
> Reviewed-by: Daniel Vetter <[email protected]>
Thank you
>
> Please resubmit as a stand-alone patch, patchwork can't pull patches out
> of attachments :-/
oh, that was for demonstration purpose only, so we
are on the same page and see the patch we are discussing ;)
> -Daniel
>
>>
>> if (!pipe->funcs || !pipe->funcs->check)
>> return 0;
>> --
>> 2.7.4
>>
>> _______________________________________________
>> dri-devel mailing list
>> [email protected]
>> https://lists.freedesktop.org/mailman/listinfo/dri-devel
>
On 02/20/2018 02:53 PM, Oleksandr Andrushchenko wrote:
> On 02/20/2018 02:49 PM, Daniel Vetter wrote:
>> On Tue, Feb 20, 2018 at 02:36:05PM +0200, Oleksandr Andrushchenko wrote:
>>> On 02/20/2018 01:17 PM, Daniel Vetter wrote:
>>>> On Mon, Feb 19, 2018 at 04:58:43PM +0200, Oleksandr Andrushchenko
>>>> wrote:
>>>>> On 02/19/2018 04:30 PM, Daniel Vetter wrote:
>>>>>> On Tue, Feb 13, 2018 at 10:44:16AM +0200, Oleksandr Andrushchenko
>>>>>> wrote:
>>>>>>> From: Oleksandr Andrushchenko <[email protected]>
>>>>>>>
>>>>>>> It is possible that drm_simple_kms_plane_atomic_check called
>>>>>>> with no CRTC set, e.g. when user-space application sets
>>>>>>> CRTC_ID/FB_ID
>>>>>>> to 0 before doing any actual drawing. This leads to NULL pointer
>>>>>>> dereference because in this case new CRTC state is NULL and must be
>>>>>>> checked before accessing.
>>>>>>>
>>>>>>> Signed-off-by: Oleksandr Andrushchenko
>>>>>>> <[email protected]>
>>>>>>> ---
>>>>>>> drivers/gpu/drm/drm_simple_kms_helper.c | 6 ++++--
>>>>>>> 1 file changed, 4 insertions(+), 2 deletions(-)
>>>>>>>
>>>>>>> diff --git a/drivers/gpu/drm/drm_simple_kms_helper.c
>>>>>>> b/drivers/gpu/drm/drm_simple_kms_helper.c
>>>>>>> index 9ca8a4a59b74..a05eca9cec8b 100644
>>>>>>> --- a/drivers/gpu/drm/drm_simple_kms_helper.c
>>>>>>> +++ b/drivers/gpu/drm/drm_simple_kms_helper.c
>>>>>>> @@ -121,8 +121,10 @@ static int
>>>>>>> drm_simple_kms_plane_atomic_check(struct drm_plane *plane,
>>>>>>> pipe = container_of(plane, struct
>>>>>>> drm_simple_display_pipe, plane);
>>>>>>> crtc_state =
>>>>>>> drm_atomic_get_new_crtc_state(plane_state->state,
>>>>>>> &pipe->crtc);
>>>>>>> - if (!crtc_state->enable)
>>>>>>> - return 0; /* nothing to check when disabling or
>>>>>>> disabled */
>>>>>>> +
>>>>>>> + if (!crtc_state || !crtc_state->enable)
>>>>>>> + /* nothing to check when disabling or disabled or no
>>>>>>> CRTC set */
>>>>>>> + return 0;
>>>>>>> if (crtc_state->enable)
>>>>>>> drm_mode_get_hv_timing(&crtc_state->mode,
>>>>>> Hm, this is a bit annoying, since the can_position = false
>>>>>> parameter to
>>>>>> drm_atomic_helper_check_plane_state is supposed to catch all
>>>>>> this. Would
>>>>>> moving all the checks after the call to that helper, and gating
>>>>>> them on
>>>>>> plane_state->visible also work?
>>>>> Yes, it does work if this is what you mean:
>>>> I wasn't sure, thanks for figuring this out!
>>>>
>>>>> diff --git a/drivers/gpu/drm/drm_simple_kms_helper.c
>>>>> b/drivers/gpu/drm/drm_simple_kms_helper.c
>>>>> index a05eca9cec8b..c48858bb2823 100644
>>>>> --- a/drivers/gpu/drm/drm_simple_kms_helper.c
>>>>> +++ b/drivers/gpu/drm/drm_simple_kms_helper.c
>>>>> @@ -122,14 +122,6 @@ static int
>>>>> drm_simple_kms_plane_atomic_check(struct
>>>>> drm_plane *plane,
>>>>> crtc_state =
>>>>> drm_atomic_get_new_crtc_state(plane_state->state,
>>>>> &pipe->crtc);
>>>>>
>>>>> - if (!crtc_state || !crtc_state->enable)
>>>>> - /* nothing to check when disabling or disabled or
>>>>> no CRTC
>>>>> set */
>>>>> - return 0;
>>>>> -
>>>>> - if (crtc_state->enable)
>>>>> - drm_mode_get_hv_timing(&crtc_state->mode,
>>>>> - &clip.x2, &clip.y2);
>>>>> -
>>>>> ret = drm_atomic_helper_check_plane_state(plane_state,
>>>>> crtc_state,
>>>>> &clip,
>>>>> DRM_PLANE_HELPER_NO_SCALING,
>>>>> @@ -138,6 +130,13 @@ static int
>>>>> drm_simple_kms_plane_atomic_check(struct
>>>>> drm_plane *plane,
>>>>> if (ret)
>>>>> return ret;
>>>>>
>>>>> + if (!plane_state->visible || !crtc_state->enable)
>>>>> + return 0; /* nothing to check when disabling or
>>>>> disabled */
>>>> if (!plane_state->visible) {
>>>> WARN_ON(crtc_state->enabled);
>>>> return 0;
>>>> }
>>>>
>>>> The helper call above should guarantee this.
>>> Yes, but I still see cases when crtc_state is NULL, thus
>>> making crtc_state->enable to fail
>> Right, when the plane is completely off there's no CRTC state. Correct
>> check should be
>>
>> WARN_ON(crtc_state && crtc_state->enabled);
> ok, will update with this additional check
huh, this indeed solves the NULL pointer dereference, but floods a lot
with every page flip I have, e.g. !plane_state->visible == true
and crtc_state is not NULL and crtc_state->enable == true,
thus firing WARN_ON.
Is this something wrong with my use-case/driver or it is still legal
to have such a configuration and leave it without WARN_ON and just
return 0?
>>
>>>>> +
>>>>> + if (plane_state->visible && crtc_state->enable)
>>>> Similar here.
>>>>
>>>>> + drm_mode_get_hv_timing(&crtc_state->mode,
>>>>> + &clip.x2, &clip.y2);
>>>>> +
>>>>> if (!plane_state->visible)
>>>>> return -EINVAL;
>>>> This can now be removed, the plane helper takes care of checking for
>>>> plane_state->visible != crtc_state->enable. Please also remove.
>>>>
>>>>>> We'd need to add a guarantee to
>>>>>> drm_atomic_helper_check_plane_state that
>>>>>> it can cope with crtc_state == NULL, but I think that's a good idea
>>>>>> anyway. Atm it shouldn't end up looking at the crtc_state pointer
>>>>>> in that
>>>>>> case.
>>>>> It doesn't look at it at the moment
>>>>>> Otherwise we'll just go with your fix, but it feels all a bit too
>>>>>> fragile,
>>>>>> hence why I want to explore more robust options a bit.
>>>>> At list with the change above it passes my test which failed
>>>>> before. Although I cannot confirm it works for others, but it
>>>>> certainly does for me.
>>>>>> -Daniel
>>>>> Do you want me to send v1 with the code above?
>>>> Yes please, with my above cleanup suggestions.
>>> Please see the patch under test attached (I believe it is what you
>>> mean,
>>> with the only change that
>>> if (!plane_state->visible) {
>>> *if (crtc_state)*
>>> WARN_ON(crtc_state->enable);
>>> return 0;
>>> }
>>> check is used).
>>>
>>> Whith this patch + additional logs I have:
>>>
>>> [ 18.939204] [drm:drm_ioctl [drm]] pid=2105, dev=0xe200, auth=1,
>>> DRM_IOCTL_MODE_ATOMIC
>>> [...]
>>> [ 18.939681] [drm:drm_atomic_set_crtc_for_plane [drm]] Link plane
>>> state
>>> 00000000c302cbbf to [NOCRTC]
>>> [ 18.939822] [drm:drm_atomic_set_fb_for_plane [drm]] Set [NOFB]
>>> for plane
>>> state 00000000c302cbbf
>>> [ 18.939963] [drm:drm_atomic_print_state [drm]] checking
>>> 000000000bc224e7
>>> [ 18.939988] vdispl vdispl.0: [drm] plane[29]: plane-0
>>> [ 18.940003] vdispl vdispl.0: [drm] crtc=(null)
>>> [ 18.940018] vdispl vdispl.0: [drm] fb=0
>>> [ 18.940032] vdispl vdispl.0: [drm] crtc-pos=0x0+0+0
>>> [ 18.940048] vdispl vdispl.0: [drm]
>>> src-pos=0.000000x0.000000+0.000000+0.000000
>>> [ 18.940067] vdispl vdispl.0: [drm] rotation=1
>>> [ 18.940199] [drm:drm_atomic_check_only [drm]] checking
>>> 000000000bc224e7
>>> [ 18.940226] ================================= plane_state->visible 0
>>> crtc_state (null)
>>> [...]
>>> [ 18.978146] [drm:drm_atomic_set_crtc_for_plane [drm]] Link plane
>>> state
>>> 000000006bd50580 to [CRTC:30:crtc-0]
>>> [ 18.978292] [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:35]
>>> for plane
>>> state 000000006bd50580
>>> [ 18.978993] [drm:drm_atomic_set_mode_prop_for_crtc [drm]] Set
>>> [MODE:1024x768] for CRTC state 00000000e5a28f6a
>>> [ 18.979425] [drm:drm_atomic_check_only [drm]] checking
>>> 000000000bc224e7
>>> [ 18.979540] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]]
>>> [CRTC:30:crtc-0] mode changed
>>> [ 18.979632] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]]
>>> [CRTC:30:crtc-0] enable changed
>>> [ 18.979708] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]]
>>> [CRTC:30:crtc-0] active changed
>>> [ 18.979792] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]]
>>> Updating routing for [CONNECTOR:28:Virtual-1]
>>> [ 18.979877] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]]
>>> [CONNECTOR:28:Virtual-1] using [ENCODER:31:None-31] on [CRTC:30:crtc-0]
>>> [ 18.979960] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]]
>>> [CRTC:30:crtc-0] needs all connectors, enable: y, active: y
>>> [ 18.980139] [drm:drm_atomic_add_affected_connectors [drm]] Adding
>>> all
>>> current connectors for [CRTC:30:crtc-0] to 000000000bc224e7
>>> [ 18.980184] ================================= plane_state->visible 0
>>> crtc_state 00000000e5a28f6a
>>> [ 18.980205] crtc_state->enable 1
>>>
>>> *[ 19.022608] WARNING: CPU: 1 PID: 2105 at
>>> drivers/gpu/drm/drm_simple_kms_helper.c:137
>>> drm_simple_kms_plane_atomic_check+0xdc/0xf8 [drm_kms_helper]*
>>>
>>> [...]
>>>
>>> [ 19.113601] ================================= plane_state->visible 0
>>> crtc_state 00000000e5a28f6a
>>> [ 19.113623] crtc_state->enable 1
>>> [ 19.113792] WARNING: CPU: 1 PID: 2105 at
>>> drivers/gpu/drm/drm_simple_kms_helper.c:137
>>> drm_simple_kms_plane_atomic_check+0xdc/0xf8 [drm_kms_helper]
>>>
>>> [...]
>>>
>>> And finally
>>>
>>> [ 19.340249] ================================= plane_state->visible 0
>>> crtc_state 0000000036a1b1f5
>>> [ 19.340271] crtc_state->enable 0
>>>
>>> So, it seems that crtc_state can still be NULL if
>>> "!plane_state->visible"
>>> making
>>> NULL pointer dereference, so we need a check for that.
>>> Yet, !plane_state->visible && crtc_state->enable makes WARN_ON to fire
>>> always. So, probably we may want removing it.
>>>> Thanks, Daniel
>>> Thank you,
>>> Oleksandr
>>> From dbcce708b237740158a2c16029c56a579324f269 Mon Sep 17 00:00:00 2001
>>> From: Oleksandr Andrushchenko <[email protected]>
>>> Date: Tue, 13 Feb 2018 10:32:20 +0200
>>> Subject: [PATCH] drm/simple_kms_helper: Fix NULL pointer dereference
>>> with no
>>> active CRTC
>>>
>>> It is possible that drm_simple_kms_plane_atomic_check called
>>> with no CRTC set, e.g. when user-space application sets CRTC_ID/FB_ID
>>> to 0 before doing any actual drawing. This leads to NULL pointer
>>> dereference because in this case new CRTC state is NULL and must be
>>> checked before accessing.
>>>
>>> Signed-off-by: Oleksandr Andrushchenko
>>> <[email protected]>
>>> ---
>>> drivers/gpu/drm/drm_simple_kms_helper.c | 15 +++++++--------
>>> 1 file changed, 7 insertions(+), 8 deletions(-)
>>>
>>> diff --git a/drivers/gpu/drm/drm_simple_kms_helper.c
>>> b/drivers/gpu/drm/drm_simple_kms_helper.c
>>> index 9ca8a4a59b74..f54711ff9767 100644
>>> --- a/drivers/gpu/drm/drm_simple_kms_helper.c
>>> +++ b/drivers/gpu/drm/drm_simple_kms_helper.c
>>> @@ -121,12 +121,6 @@ static int
>>> drm_simple_kms_plane_atomic_check(struct drm_plane *plane,
>>> pipe = container_of(plane, struct drm_simple_display_pipe,
>>> plane);
>>> crtc_state = drm_atomic_get_new_crtc_state(plane_state->state,
>>> &pipe->crtc);
>>> - if (!crtc_state->enable)
>>> - return 0; /* nothing to check when disabling or disabled */
>>> -
>>> - if (crtc_state->enable)
>>> - drm_mode_get_hv_timing(&crtc_state->mode,
>>> - &clip.x2, &clip.y2);
>>> ret = drm_atomic_helper_check_plane_state(plane_state,
>>> crtc_state,
>>> &clip,
>>> @@ -136,8 +130,13 @@ static int
>>> drm_simple_kms_plane_atomic_check(struct drm_plane *plane,
>>> if (ret)
>>> return ret;
>>> - if (!plane_state->visible)
>>> - return -EINVAL;
>>> + if (!plane_state->visible) {
>>> + if (crtc_state)
>>> + WARN_ON(crtc_state->enable);
>>> + return 0;
>>> + }
>>> +
>>> + drm_mode_get_hv_timing(&crtc_state->mode, &clip.x2, &clip.y2);
>> lgtm. With or without the bikeshed to pull the crtc_state check into the
>> WARN_ON.
>>
>> Reviewed-by: Daniel Vetter <[email protected]>
> Thank you
>>
>> Please resubmit as a stand-alone patch, patchwork can't pull patches out
>> of attachments :-/
> oh, that was for demonstration purpose only, so we
> are on the same page and see the patch we are discussing ;)
>> -Daniel
>>
>>> if (!pipe->funcs || !pipe->funcs->check)
>>> return 0;
>>> --
>>> 2.7.4
>>>
>>> _______________________________________________
>>> dri-devel mailing list
>>> [email protected]
>>> https://lists.freedesktop.org/mailman/listinfo/dri-devel
>>
>
On Tue, Feb 20, 2018 at 03:29:07PM +0200, Oleksandr Andrushchenko wrote:
> On 02/20/2018 02:53 PM, Oleksandr Andrushchenko wrote:
> > On 02/20/2018 02:49 PM, Daniel Vetter wrote:
> > > On Tue, Feb 20, 2018 at 02:36:05PM +0200, Oleksandr Andrushchenko wrote:
> > > > On 02/20/2018 01:17 PM, Daniel Vetter wrote:
> > > > > On Mon, Feb 19, 2018 at 04:58:43PM +0200, Oleksandr
> > > > > Andrushchenko wrote:
> > > > > > On 02/19/2018 04:30 PM, Daniel Vetter wrote:
> > > > > > > On Tue, Feb 13, 2018 at 10:44:16AM +0200, Oleksandr
> > > > > > > Andrushchenko wrote:
> > > > > > > > From: Oleksandr Andrushchenko <[email protected]>
> > > > > > > >
> > > > > > > > It is possible that drm_simple_kms_plane_atomic_check called
> > > > > > > > with no CRTC set, e.g. when user-space
> > > > > > > > application sets CRTC_ID/FB_ID
> > > > > > > > to 0 before doing any actual drawing. This leads to NULL pointer
> > > > > > > > dereference because in this case new CRTC state is NULL and must be
> > > > > > > > checked before accessing.
> > > > > > > >
> > > > > > > > Signed-off-by: Oleksandr Andrushchenko
> > > > > > > > <[email protected]>
> > > > > > > > ---
> > > > > > > > ??? drivers/gpu/drm/drm_simple_kms_helper.c | 6 ++++--
> > > > > > > > ??? 1 file changed, 4 insertions(+), 2 deletions(-)
> > > > > > > >
> > > > > > > > diff --git
> > > > > > > > a/drivers/gpu/drm/drm_simple_kms_helper.c
> > > > > > > > b/drivers/gpu/drm/drm_simple_kms_helper.c
> > > > > > > > index 9ca8a4a59b74..a05eca9cec8b 100644
> > > > > > > > --- a/drivers/gpu/drm/drm_simple_kms_helper.c
> > > > > > > > +++ b/drivers/gpu/drm/drm_simple_kms_helper.c
> > > > > > > > @@ -121,8 +121,10 @@ static int
> > > > > > > > drm_simple_kms_plane_atomic_check(struct
> > > > > > > > drm_plane *plane,
> > > > > > > > ??????? pipe = container_of(plane, struct
> > > > > > > > drm_simple_display_pipe, plane);
> > > > > > > > ??????? crtc_state =
> > > > > > > > drm_atomic_get_new_crtc_state(plane_state->state,
> > > > > > > > ?????????????????????????????? &pipe->crtc);
> > > > > > > > -??? if (!crtc_state->enable)
> > > > > > > > -??????? return 0; /* nothing to check when
> > > > > > > > disabling or disabled */
> > > > > > > > +
> > > > > > > > +??? if (!crtc_state || !crtc_state->enable)
> > > > > > > > +??????? /* nothing to check when disabling or
> > > > > > > > disabled or no CRTC set */
> > > > > > > > +??????? return 0;
> > > > > > > > ??????? if (crtc_state->enable)
> > > > > > > > drm_mode_get_hv_timing(&crtc_state->mode,
> > > > > > > Hm, this is a bit annoying, since the can_position =
> > > > > > > false parameter to
> > > > > > > drm_atomic_helper_check_plane_state is supposed to
> > > > > > > catch all this. Would
> > > > > > > moving all the checks after the call to that helper,
> > > > > > > and gating them on
> > > > > > > plane_state->visible also work?
> > > > > > Yes, it does work if this is what you mean:
> > > > > I wasn't sure, thanks for figuring this out!
> > > > >
> > > > > > diff --git a/drivers/gpu/drm/drm_simple_kms_helper.c
> > > > > > b/drivers/gpu/drm/drm_simple_kms_helper.c
> > > > > > index a05eca9cec8b..c48858bb2823 100644
> > > > > > --- a/drivers/gpu/drm/drm_simple_kms_helper.c
> > > > > > +++ b/drivers/gpu/drm/drm_simple_kms_helper.c
> > > > > > @@ -122,14 +122,6 @@ static int
> > > > > > drm_simple_kms_plane_atomic_check(struct
> > > > > > drm_plane *plane,
> > > > > > ? ??????? crtc_state =
> > > > > > drm_atomic_get_new_crtc_state(plane_state->state,
> > > > > > &pipe->crtc);
> > > > > >
> > > > > > -?????? if (!crtc_state || !crtc_state->enable)
> > > > > > -?????????????? /* nothing to check when disabling or
> > > > > > disabled or no CRTC
> > > > > > set */
> > > > > > -?????????????? return 0;
> > > > > > -
> > > > > > -?????? if (crtc_state->enable)
> > > > > > - drm_mode_get_hv_timing(&crtc_state->mode,
> > > > > > -????????????????????????????????????? &clip.x2, &clip.y2);
> > > > > > -
> > > > > > ? ??????? ret =
> > > > > > drm_atomic_helper_check_plane_state(plane_state,
> > > > > > crtc_state,
> > > > > > &clip,
> > > > > > DRM_PLANE_HELPER_NO_SCALING,
> > > > > > @@ -138,6 +130,13 @@ static int
> > > > > > drm_simple_kms_plane_atomic_check(struct
> > > > > > drm_plane *plane,
> > > > > > ? ??????? if (ret)
> > > > > > ? ??????????????? return ret;
> > > > > >
> > > > > > +?????? if (!plane_state->visible || !crtc_state->enable)
> > > > > > +?????????????? return 0; /* nothing to check when
> > > > > > disabling or disabled */
> > > > > if (!plane_state->visible) {
> > > > > ????WARN_ON(crtc_state->enabled);
> > > > > ????return 0;
> > > > > }
> > > > >
> > > > > The helper call above should guarantee this.
> > > > Yes, but I still see cases when crtc_state is NULL, thus
> > > > making crtc_state->enable to fail
> > > Right, when the plane is completely off there's no CRTC state. Correct
> > > check should be
> > >
> > > ????WARN_ON(crtc_state && crtc_state->enabled);
> > ok, will update with this additional check
> huh, this indeed solves the NULL pointer dereference, but floods a lot
> with every page flip I have, e.g. !plane_state->visible == true
> and crtc_state is not NULL and crtc_state->enable == true,
> thus firing WARN_ON.
> Is this something wrong with my use-case/driver or it is still legal
> to have such a configuration and leave it without WARN_ON and just
> return 0?
1 week of vacation later I have to admit that this WARN_ON is completely
bogus :-)
Sorry for all the confusion, pls leave it out.
-Daniel
> > >
> > > > > > +
> > > > > > +?????? if (plane_state->visible && crtc_state->enable)
> > > > > Similar here.
> > > > >
> > > > > > + drm_mode_get_hv_timing(&crtc_state->mode,
> > > > > > +????????????????????????????????????? &clip.x2, &clip.y2);
> > > > > > +
> > > > > > ? ??????? if (!plane_state->visible)
> > > > > > ? ??????????????? return -EINVAL;
> > > > > This can now be removed, the plane helper takes care of checking for
> > > > > plane_state->visible != crtc_state->enable. Please also remove.
> > > > >
> > > > > > > We'd need to add a guarantee to
> > > > > > > drm_atomic_helper_check_plane_state that
> > > > > > > it can cope with crtc_state == NULL, but I think that's a good idea
> > > > > > > anyway. Atm it shouldn't end up looking at the
> > > > > > > crtc_state pointer in that
> > > > > > > case.
> > > > > > It doesn't look at it at the moment
> > > > > > > Otherwise we'll just go with your fix, but it feels
> > > > > > > all a bit too fragile,
> > > > > > > hence why I want to explore more robust options a bit.
> > > > > > At list with the change above it passes my test which failed
> > > > > > before. Although I cannot confirm it works for others, but it
> > > > > > certainly does for me.
> > > > > > > -Daniel
> > > > > > Do you want me to send v1 with the code above?
> > > > > Yes please, with my above cleanup suggestions.
> > > > Please see the patch under test attached (I believe it is what
> > > > you mean,
> > > > with the only change that
> > > > ???? if (!plane_state->visible) {
> > > > ???? ??? *if (crtc_state)*
> > > > ???? ??? ??? WARN_ON(crtc_state->enable);
> > > > ???? ??? return 0;
> > > > ???? }
> > > > check is used).
> > > >
> > > > Whith this patch + additional logs I have:
> > > >
> > > > [?? 18.939204] [drm:drm_ioctl [drm]] pid=2105, dev=0xe200, auth=1,
> > > > DRM_IOCTL_MODE_ATOMIC
> > > > [...]
> > > > [?? 18.939681] [drm:drm_atomic_set_crtc_for_plane [drm]] Link
> > > > plane state
> > > > 00000000c302cbbf to [NOCRTC]
> > > > [?? 18.939822] [drm:drm_atomic_set_fb_for_plane [drm]] Set
> > > > [NOFB] for plane
> > > > state 00000000c302cbbf
> > > > [?? 18.939963] [drm:drm_atomic_print_state [drm]] checking
> > > > 000000000bc224e7
> > > > [?? 18.939988] vdispl vdispl.0: [drm] plane[29]: plane-0
> > > > [?? 18.940003] vdispl vdispl.0: [drm]?? crtc=(null)
> > > > [?? 18.940018] vdispl vdispl.0: [drm]?? fb=0
> > > > [?? 18.940032] vdispl vdispl.0: [drm]?? crtc-pos=0x0+0+0
> > > > [?? 18.940048] vdispl vdispl.0: [drm]
> > > > src-pos=0.000000x0.000000+0.000000+0.000000
> > > > [?? 18.940067] vdispl vdispl.0: [drm]?? rotation=1
> > > > [?? 18.940199] [drm:drm_atomic_check_only [drm]] checking
> > > > 000000000bc224e7
> > > > [?? 18.940226] ================================= plane_state->visible 0
> > > > crtc_state?????????? (null)
> > > > [...]
> > > > [?? 18.978146] [drm:drm_atomic_set_crtc_for_plane [drm]] Link
> > > > plane state
> > > > 000000006bd50580 to [CRTC:30:crtc-0]
> > > > [?? 18.978292] [drm:drm_atomic_set_fb_for_plane [drm]] Set
> > > > [FB:35] for plane
> > > > state 000000006bd50580
> > > > [?? 18.978993] [drm:drm_atomic_set_mode_prop_for_crtc [drm]] Set
> > > > [MODE:1024x768] for CRTC state 00000000e5a28f6a
> > > > [?? 18.979425] [drm:drm_atomic_check_only [drm]] checking
> > > > 000000000bc224e7
> > > > [?? 18.979540] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]]
> > > > [CRTC:30:crtc-0] mode changed
> > > > [?? 18.979632] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]]
> > > > [CRTC:30:crtc-0] enable changed
> > > > [?? 18.979708] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]]
> > > > [CRTC:30:crtc-0] active changed
> > > > [?? 18.979792] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]]
> > > > Updating routing for [CONNECTOR:28:Virtual-1]
> > > > [?? 18.979877] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]]
> > > > [CONNECTOR:28:Virtual-1] using [ENCODER:31:None-31] on [CRTC:30:crtc-0]
> > > > [?? 18.979960] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]]
> > > > [CRTC:30:crtc-0] needs all connectors, enable: y, active: y
> > > > [?? 18.980139] [drm:drm_atomic_add_affected_connectors [drm]]
> > > > Adding all
> > > > current connectors for [CRTC:30:crtc-0] to 000000000bc224e7
> > > > [?? 18.980184] ================================= plane_state->visible 0
> > > > crtc_state 00000000e5a28f6a
> > > > [?? 18.980205] crtc_state->enable 1
> > > >
> > > > *[?? 19.022608] WARNING: CPU: 1 PID: 2105 at
> > > > drivers/gpu/drm/drm_simple_kms_helper.c:137
> > > > drm_simple_kms_plane_atomic_check+0xdc/0xf8 [drm_kms_helper]*
> > > >
> > > > [...]
> > > >
> > > > [?? 19.113601] ================================= plane_state->visible 0
> > > > crtc_state 00000000e5a28f6a
> > > > [?? 19.113623] crtc_state->enable 1
> > > > [?? 19.113792] WARNING: CPU: 1 PID: 2105 at
> > > > drivers/gpu/drm/drm_simple_kms_helper.c:137
> > > > drm_simple_kms_plane_atomic_check+0xdc/0xf8 [drm_kms_helper]
> > > >
> > > > [...]
> > > >
> > > > And finally
> > > >
> > > > [?? 19.340249] ================================= plane_state->visible 0
> > > > crtc_state 0000000036a1b1f5
> > > > [?? 19.340271] crtc_state->enable 0
> > > >
> > > > So, it seems that crtc_state can still be NULL if
> > > > "!plane_state->visible"
> > > > making
> > > > NULL pointer dereference, so we need a check for that.
> > > > Yet, !plane_state->visible && crtc_state->enable makes WARN_ON to fire
> > > > always. So, probably we may want removing it.
> > > > > Thanks, Daniel
> > > > Thank you,
> > > > Oleksandr
> > > > ?From dbcce708b237740158a2c16029c56a579324f269 Mon Sep 17 00:00:00 2001
> > > > From: Oleksandr Andrushchenko <[email protected]>
> > > > Date: Tue, 13 Feb 2018 10:32:20 +0200
> > > > Subject: [PATCH] drm/simple_kms_helper: Fix NULL pointer
> > > > dereference with no
> > > > ? active CRTC
> > > >
> > > > It is possible that drm_simple_kms_plane_atomic_check called
> > > > with no CRTC set, e.g. when user-space application sets CRTC_ID/FB_ID
> > > > to 0 before doing any actual drawing. This leads to NULL pointer
> > > > dereference because in this case new CRTC state is NULL and must be
> > > > checked before accessing.
> > > >
> > > > Signed-off-by: Oleksandr Andrushchenko
> > > > <[email protected]>
> > > > ---
> > > > ? drivers/gpu/drm/drm_simple_kms_helper.c | 15 +++++++--------
> > > > ? 1 file changed, 7 insertions(+), 8 deletions(-)
> > > >
> > > > diff --git a/drivers/gpu/drm/drm_simple_kms_helper.c
> > > > b/drivers/gpu/drm/drm_simple_kms_helper.c
> > > > index 9ca8a4a59b74..f54711ff9767 100644
> > > > --- a/drivers/gpu/drm/drm_simple_kms_helper.c
> > > > +++ b/drivers/gpu/drm/drm_simple_kms_helper.c
> > > > @@ -121,12 +121,6 @@ static int
> > > > drm_simple_kms_plane_atomic_check(struct drm_plane *plane,
> > > > ????? pipe = container_of(plane, struct drm_simple_display_pipe,
> > > > plane);
> > > > ????? crtc_state = drm_atomic_get_new_crtc_state(plane_state->state,
> > > > ???????????????????????????? &pipe->crtc);
> > > > -??? if (!crtc_state->enable)
> > > > -??????? return 0; /* nothing to check when disabling or disabled */
> > > > -
> > > > -??? if (crtc_state->enable)
> > > > -??????? drm_mode_get_hv_timing(&crtc_state->mode,
> > > > -?????????????????????? &clip.x2, &clip.y2);
> > > > ? ????? ret = drm_atomic_helper_check_plane_state(plane_state,
> > > > crtc_state,
> > > > ??????????????????????????? &clip,
> > > > @@ -136,8 +130,13 @@ static int
> > > > drm_simple_kms_plane_atomic_check(struct drm_plane *plane,
> > > > ????? if (ret)
> > > > ????????? return ret;
> > > > ? -??? if (!plane_state->visible)
> > > > -??????? return -EINVAL;
> > > > +??? if (!plane_state->visible) {
> > > > +??????? if (crtc_state)
> > > > +??????????? WARN_ON(crtc_state->enable);
> > > > +??????? return 0;
> > > > +??? }
> > > > +
> > > > +??? drm_mode_get_hv_timing(&crtc_state->mode, &clip.x2, &clip.y2);
> > > lgtm. With or without the bikeshed to pull the crtc_state check into the
> > > WARN_ON.
> > >
> > > Reviewed-by: Daniel Vetter <[email protected]>
> > Thank you
> > >
> > > Please resubmit as a stand-alone patch, patchwork can't pull patches out
> > > of attachments :-/
> > oh, that was for demonstration purpose only, so we
> > are on the same page and see the patch we are discussing ;)
> > > -Daniel
> > >
> > > > ? ????? if (!pipe->funcs || !pipe->funcs->check)
> > > > ????????? return 0;
> > > > --
> > > > 2.7.4
> > > >
> > > > _______________________________________________
> > > > dri-devel mailing list
> > > > [email protected]
> > > > https://lists.freedesktop.org/mailman/listinfo/dri-devel
> > >
> >
>
> _______________________________________________
> dri-devel mailing list
> [email protected]
> https://lists.freedesktop.org/mailman/listinfo/dri-devel
--
Daniel Vetter
Software Engineer, Intel Corporation
http://blog.ffwll.ch
On 03/05/2018 10:52 AM, Daniel Vetter wrote:
> On Tue, Feb 20, 2018 at 03:29:07PM +0200, Oleksandr Andrushchenko wrote:
>> On 02/20/2018 02:53 PM, Oleksandr Andrushchenko wrote:
>>> On 02/20/2018 02:49 PM, Daniel Vetter wrote:
>>>> On Tue, Feb 20, 2018 at 02:36:05PM +0200, Oleksandr Andrushchenko wrote:
>>>>> On 02/20/2018 01:17 PM, Daniel Vetter wrote:
>>>>>> On Mon, Feb 19, 2018 at 04:58:43PM +0200, Oleksandr
>>>>>> Andrushchenko wrote:
>>>>>>> On 02/19/2018 04:30 PM, Daniel Vetter wrote:
>>>>>>>> On Tue, Feb 13, 2018 at 10:44:16AM +0200, Oleksandr
>>>>>>>> Andrushchenko wrote:
>>>>>>>>> From: Oleksandr Andrushchenko <[email protected]>
>>>>>>>>>
>>>>>>>>> It is possible that drm_simple_kms_plane_atomic_check called
>>>>>>>>> with no CRTC set, e.g. when user-space
>>>>>>>>> application sets CRTC_ID/FB_ID
>>>>>>>>> to 0 before doing any actual drawing. This leads to NULL pointer
>>>>>>>>> dereference because in this case new CRTC state is NULL and must be
>>>>>>>>> checked before accessing.
>>>>>>>>>
>>>>>>>>> Signed-off-by: Oleksandr Andrushchenko
>>>>>>>>> <[email protected]>
>>>>>>>>> ---
>>>>>>>>> drivers/gpu/drm/drm_simple_kms_helper.c | 6 ++++--
>>>>>>>>> 1 file changed, 4 insertions(+), 2 deletions(-)
>>>>>>>>>
>>>>>>>>> diff --git
>>>>>>>>> a/drivers/gpu/drm/drm_simple_kms_helper.c
>>>>>>>>> b/drivers/gpu/drm/drm_simple_kms_helper.c
>>>>>>>>> index 9ca8a4a59b74..a05eca9cec8b 100644
>>>>>>>>> --- a/drivers/gpu/drm/drm_simple_kms_helper.c
>>>>>>>>> +++ b/drivers/gpu/drm/drm_simple_kms_helper.c
>>>>>>>>> @@ -121,8 +121,10 @@ static int
>>>>>>>>> drm_simple_kms_plane_atomic_check(struct
>>>>>>>>> drm_plane *plane,
>>>>>>>>> pipe = container_of(plane, struct
>>>>>>>>> drm_simple_display_pipe, plane);
>>>>>>>>> crtc_state =
>>>>>>>>> drm_atomic_get_new_crtc_state(plane_state->state,
>>>>>>>>> &pipe->crtc);
>>>>>>>>> - if (!crtc_state->enable)
>>>>>>>>> - return 0; /* nothing to check when
>>>>>>>>> disabling or disabled */
>>>>>>>>> +
>>>>>>>>> + if (!crtc_state || !crtc_state->enable)
>>>>>>>>> + /* nothing to check when disabling or
>>>>>>>>> disabled or no CRTC set */
>>>>>>>>> + return 0;
>>>>>>>>> if (crtc_state->enable)
>>>>>>>>> drm_mode_get_hv_timing(&crtc_state->mode,
>>>>>>>> Hm, this is a bit annoying, since the can_position =
>>>>>>>> false parameter to
>>>>>>>> drm_atomic_helper_check_plane_state is supposed to
>>>>>>>> catch all this. Would
>>>>>>>> moving all the checks after the call to that helper,
>>>>>>>> and gating them on
>>>>>>>> plane_state->visible also work?
>>>>>>> Yes, it does work if this is what you mean:
>>>>>> I wasn't sure, thanks for figuring this out!
>>>>>>
>>>>>>> diff --git a/drivers/gpu/drm/drm_simple_kms_helper.c
>>>>>>> b/drivers/gpu/drm/drm_simple_kms_helper.c
>>>>>>> index a05eca9cec8b..c48858bb2823 100644
>>>>>>> --- a/drivers/gpu/drm/drm_simple_kms_helper.c
>>>>>>> +++ b/drivers/gpu/drm/drm_simple_kms_helper.c
>>>>>>> @@ -122,14 +122,6 @@ static int
>>>>>>> drm_simple_kms_plane_atomic_check(struct
>>>>>>> drm_plane *plane,
>>>>>>> crtc_state =
>>>>>>> drm_atomic_get_new_crtc_state(plane_state->state,
>>>>>>> &pipe->crtc);
>>>>>>>
>>>>>>> - if (!crtc_state || !crtc_state->enable)
>>>>>>> - /* nothing to check when disabling or
>>>>>>> disabled or no CRTC
>>>>>>> set */
>>>>>>> - return 0;
>>>>>>> -
>>>>>>> - if (crtc_state->enable)
>>>>>>> - drm_mode_get_hv_timing(&crtc_state->mode,
>>>>>>> - &clip.x2, &clip.y2);
>>>>>>> -
>>>>>>> ret =
>>>>>>> drm_atomic_helper_check_plane_state(plane_state,
>>>>>>> crtc_state,
>>>>>>> &clip,
>>>>>>> DRM_PLANE_HELPER_NO_SCALING,
>>>>>>> @@ -138,6 +130,13 @@ static int
>>>>>>> drm_simple_kms_plane_atomic_check(struct
>>>>>>> drm_plane *plane,
>>>>>>> if (ret)
>>>>>>> return ret;
>>>>>>>
>>>>>>> + if (!plane_state->visible || !crtc_state->enable)
>>>>>>> + return 0; /* nothing to check when
>>>>>>> disabling or disabled */
>>>>>> if (!plane_state->visible) {
>>>>>> WARN_ON(crtc_state->enabled);
>>>>>> return 0;
>>>>>> }
>>>>>>
>>>>>> The helper call above should guarantee this.
>>>>> Yes, but I still see cases when crtc_state is NULL, thus
>>>>> making crtc_state->enable to fail
>>>> Right, when the plane is completely off there's no CRTC state. Correct
>>>> check should be
>>>>
>>>> WARN_ON(crtc_state && crtc_state->enabled);
>>> ok, will update with this additional check
>> huh, this indeed solves the NULL pointer dereference, but floods a lot
>> with every page flip I have, e.g. !plane_state->visible == true
>> and crtc_state is not NULL and crtc_state->enable == true,
>> thus firing WARN_ON.
>> Is this something wrong with my use-case/driver or it is still legal
>> to have such a configuration and leave it without WARN_ON and just
>> return 0?
> 1 week of vacation later I have to admit that this WARN_ON is completely
> bogus :-)
np ;)
> Sorry for all the confusion, pls leave it out.
> -Daniel
>
>>>>>>> +
>>>>>>> + if (plane_state->visible && crtc_state->enable)
>>>>>> Similar here.
>>>>>>
>>>>>>> + drm_mode_get_hv_timing(&crtc_state->mode,
>>>>>>> + &clip.x2, &clip.y2);
>>>>>>> +
>>>>>>> if (!plane_state->visible)
>>>>>>> return -EINVAL;
>>>>>> This can now be removed, the plane helper takes care of checking for
>>>>>> plane_state->visible != crtc_state->enable. Please also remove.
>>>>>>
>>>>>>>> We'd need to add a guarantee to
>>>>>>>> drm_atomic_helper_check_plane_state that
>>>>>>>> it can cope with crtc_state == NULL, but I think that's a good idea
>>>>>>>> anyway. Atm it shouldn't end up looking at the
>>>>>>>> crtc_state pointer in that
>>>>>>>> case.
>>>>>>> It doesn't look at it at the moment
>>>>>>>> Otherwise we'll just go with your fix, but it feels
>>>>>>>> all a bit too fragile,
>>>>>>>> hence why I want to explore more robust options a bit.
>>>>>>> At list with the change above it passes my test which failed
>>>>>>> before. Although I cannot confirm it works for others, but it
>>>>>>> certainly does for me.
>>>>>>>> -Daniel
>>>>>>> Do you want me to send v1 with the code above?
>>>>>> Yes please, with my above cleanup suggestions.
>>>>> Please see the patch under test attached (I believe it is what
>>>>> you mean,
>>>>> with the only change that
>>>>> if (!plane_state->visible) {
>>>>> *if (crtc_state)*
>>>>> WARN_ON(crtc_state->enable);
>>>>> return 0;
>>>>> }
>>>>> check is used).
>>>>>
>>>>> Whith this patch + additional logs I have:
>>>>>
>>>>> [ 18.939204] [drm:drm_ioctl [drm]] pid=2105, dev=0xe200, auth=1,
>>>>> DRM_IOCTL_MODE_ATOMIC
>>>>> [...]
>>>>> [ 18.939681] [drm:drm_atomic_set_crtc_for_plane [drm]] Link
>>>>> plane state
>>>>> 00000000c302cbbf to [NOCRTC]
>>>>> [ 18.939822] [drm:drm_atomic_set_fb_for_plane [drm]] Set
>>>>> [NOFB] for plane
>>>>> state 00000000c302cbbf
>>>>> [ 18.939963] [drm:drm_atomic_print_state [drm]] checking
>>>>> 000000000bc224e7
>>>>> [ 18.939988] vdispl vdispl.0: [drm] plane[29]: plane-0
>>>>> [ 18.940003] vdispl vdispl.0: [drm] crtc=(null)
>>>>> [ 18.940018] vdispl vdispl.0: [drm] fb=0
>>>>> [ 18.940032] vdispl vdispl.0: [drm] crtc-pos=0x0+0+0
>>>>> [ 18.940048] vdispl vdispl.0: [drm]
>>>>> src-pos=0.000000x0.000000+0.000000+0.000000
>>>>> [ 18.940067] vdispl vdispl.0: [drm] rotation=1
>>>>> [ 18.940199] [drm:drm_atomic_check_only [drm]] checking
>>>>> 000000000bc224e7
>>>>> [ 18.940226] ================================= plane_state->visible 0
>>>>> crtc_state (null)
>>>>> [...]
>>>>> [ 18.978146] [drm:drm_atomic_set_crtc_for_plane [drm]] Link
>>>>> plane state
>>>>> 000000006bd50580 to [CRTC:30:crtc-0]
>>>>> [ 18.978292] [drm:drm_atomic_set_fb_for_plane [drm]] Set
>>>>> [FB:35] for plane
>>>>> state 000000006bd50580
>>>>> [ 18.978993] [drm:drm_atomic_set_mode_prop_for_crtc [drm]] Set
>>>>> [MODE:1024x768] for CRTC state 00000000e5a28f6a
>>>>> [ 18.979425] [drm:drm_atomic_check_only [drm]] checking
>>>>> 000000000bc224e7
>>>>> [ 18.979540] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]]
>>>>> [CRTC:30:crtc-0] mode changed
>>>>> [ 18.979632] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]]
>>>>> [CRTC:30:crtc-0] enable changed
>>>>> [ 18.979708] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]]
>>>>> [CRTC:30:crtc-0] active changed
>>>>> [ 18.979792] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]]
>>>>> Updating routing for [CONNECTOR:28:Virtual-1]
>>>>> [ 18.979877] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]]
>>>>> [CONNECTOR:28:Virtual-1] using [ENCODER:31:None-31] on [CRTC:30:crtc-0]
>>>>> [ 18.979960] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]]
>>>>> [CRTC:30:crtc-0] needs all connectors, enable: y, active: y
>>>>> [ 18.980139] [drm:drm_atomic_add_affected_connectors [drm]]
>>>>> Adding all
>>>>> current connectors for [CRTC:30:crtc-0] to 000000000bc224e7
>>>>> [ 18.980184] ================================= plane_state->visible 0
>>>>> crtc_state 00000000e5a28f6a
>>>>> [ 18.980205] crtc_state->enable 1
>>>>>
>>>>> *[ 19.022608] WARNING: CPU: 1 PID: 2105 at
>>>>> drivers/gpu/drm/drm_simple_kms_helper.c:137
>>>>> drm_simple_kms_plane_atomic_check+0xdc/0xf8 [drm_kms_helper]*
>>>>>
>>>>> [...]
>>>>>
>>>>> [ 19.113601] ================================= plane_state->visible 0
>>>>> crtc_state 00000000e5a28f6a
>>>>> [ 19.113623] crtc_state->enable 1
>>>>> [ 19.113792] WARNING: CPU: 1 PID: 2105 at
>>>>> drivers/gpu/drm/drm_simple_kms_helper.c:137
>>>>> drm_simple_kms_plane_atomic_check+0xdc/0xf8 [drm_kms_helper]
>>>>>
>>>>> [...]
>>>>>
>>>>> And finally
>>>>>
>>>>> [ 19.340249] ================================= plane_state->visible 0
>>>>> crtc_state 0000000036a1b1f5
>>>>> [ 19.340271] crtc_state->enable 0
>>>>>
>>>>> So, it seems that crtc_state can still be NULL if
>>>>> "!plane_state->visible"
>>>>> making
>>>>> NULL pointer dereference, so we need a check for that.
>>>>> Yet, !plane_state->visible && crtc_state->enable makes WARN_ON to fire
>>>>> always. So, probably we may want removing it.
>>>>>> Thanks, Daniel
>>>>> Thank you,
>>>>> Oleksandr
>>>>> From dbcce708b237740158a2c16029c56a579324f269 Mon Sep 17 00:00:00 2001
>>>>> From: Oleksandr Andrushchenko <[email protected]>
>>>>> Date: Tue, 13 Feb 2018 10:32:20 +0200
>>>>> Subject: [PATCH] drm/simple_kms_helper: Fix NULL pointer
>>>>> dereference with no
>>>>> active CRTC
>>>>>
>>>>> It is possible that drm_simple_kms_plane_atomic_check called
>>>>> with no CRTC set, e.g. when user-space application sets CRTC_ID/FB_ID
>>>>> to 0 before doing any actual drawing. This leads to NULL pointer
>>>>> dereference because in this case new CRTC state is NULL and must be
>>>>> checked before accessing.
>>>>>
>>>>> Signed-off-by: Oleksandr Andrushchenko
>>>>> <[email protected]>
>>>>> ---
>>>>> drivers/gpu/drm/drm_simple_kms_helper.c | 15 +++++++--------
>>>>> 1 file changed, 7 insertions(+), 8 deletions(-)
>>>>>
>>>>> diff --git a/drivers/gpu/drm/drm_simple_kms_helper.c
>>>>> b/drivers/gpu/drm/drm_simple_kms_helper.c
>>>>> index 9ca8a4a59b74..f54711ff9767 100644
>>>>> --- a/drivers/gpu/drm/drm_simple_kms_helper.c
>>>>> +++ b/drivers/gpu/drm/drm_simple_kms_helper.c
>>>>> @@ -121,12 +121,6 @@ static int
>>>>> drm_simple_kms_plane_atomic_check(struct drm_plane *plane,
>>>>> pipe = container_of(plane, struct drm_simple_display_pipe,
>>>>> plane);
>>>>> crtc_state = drm_atomic_get_new_crtc_state(plane_state->state,
>>>>> &pipe->crtc);
>>>>> - if (!crtc_state->enable)
>>>>> - return 0; /* nothing to check when disabling or disabled */
>>>>> -
>>>>> - if (crtc_state->enable)
>>>>> - drm_mode_get_hv_timing(&crtc_state->mode,
>>>>> - &clip.x2, &clip.y2);
>>>>> ret = drm_atomic_helper_check_plane_state(plane_state,
>>>>> crtc_state,
>>>>> &clip,
>>>>> @@ -136,8 +130,13 @@ static int
>>>>> drm_simple_kms_plane_atomic_check(struct drm_plane *plane,
>>>>> if (ret)
>>>>> return ret;
>>>>> - if (!plane_state->visible)
>>>>> - return -EINVAL;
>>>>> + if (!plane_state->visible) {
>>>>> + if (crtc_state)
>>>>> + WARN_ON(crtc_state->enable);
>>>>> + return 0;
>>>>> + }
>>>>> +
>>>>> + drm_mode_get_hv_timing(&crtc_state->mode, &clip.x2, &clip.y2);
>>>> lgtm. With or without the bikeshed to pull the crtc_state check into the
>>>> WARN_ON.
>>>>
>>>> Reviewed-by: Daniel Vetter <[email protected]>
>>> Thank you
>>>> Please resubmit as a stand-alone patch, patchwork can't pull patches out
>>>> of attachments :-/
>>> oh, that was for demonstration purpose only, so we
>>> are on the same page and see the patch we are discussing ;)
>>>> -Daniel
>>>>
>>>>> if (!pipe->funcs || !pipe->funcs->check)
>>>>> return 0;
>>>>> --
>>>>> 2.7.4
>>>>>
>>>>> _______________________________________________
>>>>> dri-devel mailing list
>>>>> [email protected]
>>>>> https://lists.freedesktop.org/mailman/listinfo/dri-devel
>> _______________________________________________
>> dri-devel mailing list
>> [email protected]
>> https://lists.freedesktop.org/mailman/listinfo/dri-devel