Hi Rob,
thanks for your feedback, the changes will be included in V2 of the patch-series.
Jan
> Von: Rob Herring
> Gesendet: Sonntag, 26. November 2017 20:24
> On Thu, Nov 23, 2017 at 01:55:54PM +0100, Jan Tuerk wrote:
> > This patch adds support for the emtrion GmbH emCON-MX6 modules.
> > They are available with imx.6 Solo, Dual-Lite, Dual and Quad
> > equipped with Memory from 512MB to 2GB (configured by U-Boot).
[...]
> > +&i2c3 {
> > + clock-frequency = <100000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c3>;
> > + status = "okay";
> > +
> > + sgtl5000: sgtl5000@0a {
>
> audio-codec@a
>
> same errors repeat below.
changed for v2
>
> > + compatible = "fsl,sgtl5000";
> > + reg = <0x0a>;
> > + clocks = <&sndosc>;
> > + VDDA-supply = <&base3p3>;
> > + VDDIO-supply = <&base3p3>;
> > + };
> > +
> > + boardID: pca8754a@3A {
>
> ...@3a
changed in V2
>
> > + compatible = "nxp,pca8574";
> > + reg = <0x3A>;
>
> 0x3a
>
> > + gpio-controller;
> > + #gpio-cells = <1>;
> > + };
> > +
> > + captouch: edt-ft5x06@38 {
>
> touchscreen@38
>
> > + reg = <0x38>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_irq_touch2 &pinctrl_emcon_gpio4>;
> > + interrupt-parent = <&gpio6>;
> > + interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
> > + compatible = "edt,edt-ft5406";
> > + wake-gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
> > + wakeup-source;
> > + };
> > +};
> > +
> > +&ssi2 {
> > + status = "okay";
> > +};
> > +
> > +&rgb_encoder {
> > + status = "okay";
> > +};
> > +
[...]
> > +
> > + rgb_panel: panel {
> > + backlight = <&rgb_backlight>;
> > + power-supply = <®_prallel_disp>;
> > + port {
> > + rgb_panel_in: endpoint {
> > + remote-endpoint = <&rgb_encoder_out>;
> > + };
> > + };
> > + };
> > +
> > + rgb_backlight: rgb_backlight {
>
> rgb-backlight {
[...]
> > +
> > + lvds_backlight: lvds_backlight {
>
> lvds-backlight {
Ok, I'll change that in V2
[...]
> > +
> > +&i2c1 {
> > + clock-frequency = <100000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c1>;
> > + status = "okay";
> > +
> > + rtc: rtc@68 {
> > + compatible = "dallas,ds1307";
> > + reg = <0x68>;
> > + };
> > +
> > + da9063: da9063@58 {
>
> pmic@38
changed
>
> > + compatible = "dlg,da9063";
> > + reg = <0x58>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_pmic>;
> > + interrupt-parent = <&gpio2>;
> > +
[....]
> > +
> > + mdio {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + ksz9031: phy {
>
> phy@0
>
> Building with W=2 or W=1 will tell you this.
thanks for the hint, it will be also included in v2
>
> > + reg = <0>;
> > + compatible = "ethernet-phy-ieee802.3-c22";
> > + interrupt-parent = <&gpio1>;
> > + interrupts = <30 IRQ_TYPE_EDGE_FALLING>;
> > + rxdv-skew-ps = <480>;
> > + txen-skew-ps = <480>;
[...]
emtrion GmbH
Kreativpark - Alter Schlachthof 45
76131 Karlsruhe
GERMANY
http://www.emtrion.de
_______________________________________
Amtsgericht Mannheim
HRB 110 300
Gesch�ftsf�hrer: Dieter Baur, Ramona Maurer
_______________________________________
From 1585157828838107624@xxx Sun Nov 26 19:25:08 +0000 2017
X-GM-THRID: 1584862127974366960
X-Gmail-Labels: Inbox,Category Forums,HistoricalUnread