-----Original Message-----
From: Kumar Gala [mailto:[email protected]]
Sent: 2006年5月17日 21:26
To: Zang Roy-r61911
Cc: Paul Mackerras; linuxppc-dev list; [email protected]; Yang Xin-Xin-r48390
Subject: Re: [PATCH/2.6.17-rc4 8/10] Add tsi108 8250 serial support
On May 17, 2006, at 5:14 AM, Zang Roy-r61911 wrote:
> This patch contains changes to the serial device driver specific
> for integrated
> serial port in Tsi108 Host Bridge.
>
> Signed-off-by: Alexandre Bounine <[email protected]>
> Signed-off-by: Roy Zang <[email protected]>
>
>> From nobody Mon Sep 17 00:00:00 2001
> From: roy zang <[email protected]>
> Date: Tue May 16 15:26:02 2006 +0800
> Subject: [PATCH] Add tsi108 serial support
This patch needs to go to Russell King as uart/8250 driver maintainer.
- kumar
>
> ---
>
> drivers/serial/8250.c | 17 +++++++++++++++++
> 1 files changed, 17 insertions(+), 0 deletions(-)
>
> 6cb950357e9970afa671d59f172dbc4b03f11560
> diff --git a/drivers/serial/8250.c b/drivers/serial/8250.c
> index bbf78aa..c12f516 100644
> --- a/drivers/serial/8250.c
> +++ b/drivers/serial/8250.c
> @@ -723,7 +723,9 @@ static int broken_efr(struct uart_8250_p
> static void autoconfig_16550a(struct uart_8250_port *up)
> {
> unsigned char status1, status2;
> +#ifndef CONFIG_TSI108_BRIDGE
> unsigned int iersave;
> +#endif
>
> up->port.type = PORT_16550A;
> up->capabilities |= UART_CAP_FIFO;
> @@ -833,6 +835,7 @@ static void autoconfig_16550a(struct uar
> * trying to write and read a 1 just to make sure it's not
> * already a 1 and maybe locked there before we even start start.
> */
> +#ifndef CONFIG_TSI108_BRIDGE
> iersave = serial_in(up, UART_IER);
> serial_outp(up, UART_IER, iersave & ~UART_IER_UUE);
> if (!(serial_in(up, UART_IER) & UART_IER_UUE)) {
> @@ -859,6 +862,7 @@ static void autoconfig_16550a(struct uar
> DEBUG_AUTOCONF("Couldn't force IER_UUE to 0 ");
> }
> serial_outp(up, UART_IER, iersave);
> +#endif
> }
>
> /*
> @@ -1348,7 +1352,12 @@ static irqreturn_t serial8250_interrupt(
>
> up = list_entry(l, struct uart_8250_port, list);
>
> +#ifdef CONFIG_TSI108_BRIDGE /* for TSI108_REV_Z1 errata U2 */
> + /* read IIR as part of 32-bit word */
> + iir = (in_be32((u32 *)(up->port.membase + UART_RX)) >> 8) & 0xff;
> +#else
> iir = serial_in(up, UART_IIR);
> +#endif
> if (!(iir & UART_IIR_NO_INT)) {
> serial8250_handle_port(up, regs);
>
> @@ -1529,7 +1538,9 @@ static int serial8250_startup(struct uar
> {
> struct uart_8250_port *up = (struct uart_8250_port *)port;
> unsigned long flags;
> +#ifndef CONFIG_TSI108_BRIDGE
> unsigned char lsr, iir;
> +#endif
> int retval;
>
> up->capabilities = uart_config[up->port.type].flags;
> @@ -1567,7 +1578,9 @@ #endif
> */
> (void) serial_inp(up, UART_LSR);
> (void) serial_inp(up, UART_RX);
> +#ifndef CONFIG_TSI108_BRIDGE /* for TSI108_REV_Z1 errata U2 */
> (void) serial_inp(up, UART_IIR);
> +#endif
> (void) serial_inp(up, UART_MSR);
>
> /*
> @@ -1634,6 +1647,7 @@ #endif
>
> serial8250_set_mctrl(&up->port, up->port.mctrl);
>
> +#ifndef CONFIG_TSI108_BRIDGE
> /*
> * Do a quick test to see if we receive an
> * interrupt when we enable the TX irq.
> @@ -1652,6 +1666,7 @@ #endif
> } else {
> up->bugs &= ~UART_BUG_TXEN;
> }
> +#endif
>
> spin_unlock_irqrestore(&up->port.lock, flags);
>
> @@ -1678,7 +1693,9 @@ #endif
> */
> (void) serial_inp(up, UART_LSR);
> (void) serial_inp(up, UART_RX);
> +#ifndef CONFIG_TSI108_BRIDGE /* for TSI108_REV_Z1 errata U2 */
> (void) serial_inp(up, UART_IIR);
> +#endif
> (void) serial_inp(up, UART_MSR);
>
> return 0;
> --
> 1.3.0
> _______________________________________________
> Linuxppc-dev mailing list
> [email protected]
> https://ozlabs.org/mailman/listinfo/linuxppc-dev