2001-04-24 14:11:52

by Eamonn Hamilton

[permalink] [raw]
Subject: sym53c875 error

Hi Folks.

Under all of the kernels I have access to try ( 2.2.19, 2.4.X & 2.4.X-ac* ),
when I try and write an image in XA2 format to my SCSI writer ( Yamaha
CDR-400t ), I get a DMA overrun. When I try with a kernel patched with the
beta symbios driver ( 2.1.9 ), it works just fine.

This is on a Debian woody system, using cdrecord 1.10 ( also 1.9 and 1.8
with the same symptoms ) attached to a Tekram DC390F.

Transcript as follows :

cdrecord dev=0,3,0 -dummy -xa2 firmware.iso

Cdrecord 1.10a18 (i686-pc-linux-gnu) Copyright (C) 1995-2001 J?rg Schilling
scsidev: '0,3,0'
scsibus: 0 target: 3 lun: 0
Linux sg driver version: 3.1.17
Using libscg version 'schily-0.5'
Device type : Removable CD-ROM
Version : 2
Response Format: 2
Capabilities :
Vendor_info : 'YAMAHA '
Identifikation : 'CDR400t '
Revision : '1.0q'
Device seems to be: Yamaha CDR-400.
Using generic SCSI-3/mmc CD-R driver (mmc_cdr).
Driver flags : SWABAUDIO
Starting to write CD/DVD at speed 1 in dummy mode for single session.
Last chance to quit, starting dummy write in 1 seconds.
cdrecord: Input/output error. write_g1: scsi sendcmd: retryable error
CDB: 2A 00 00 00 01 C2 00 00 1F 00
status: 0x0 (GOOD STATUS)
DMA overrun, resid: -248
cmd finished after 0.579s timeout 40s
write track data: error after 0 bytes
Sense Bytes: 70 00 00 00 00 00 00 0A 00 00 00 00 00 00 00 00 00 00


And while that lot happens, I get

sym53c875-0-<3,*>: target did not report SYNC.
sym53c875-0-<3,*>: extraneous data discarded.
sym53c875-0-<3,*>: COMMAND FAILED (89 0) @c12a3800.

Standard burns work ok, it's just the xa2 stuff I have a problem with so
far. I also tried using the old NCR driver with the same results.

Anybody got any ideas?

Cheers,
Eamonn


2001-04-24 20:19:17

by Gérard Roudier

[permalink] [raw]
Subject: Re: sym53c875 error



On Tue, 24 Apr 2001, Hamilton, Eamonn wrote:

> Hi Folks.
>
> Under all of the kernels I have access to try ( 2.2.19, 2.4.X & 2.4.X-ac* ),
> when I try and write an image in XA2 format to my SCSI writer ( Yamaha
> CDR-400t ), I get a DMA overrun. When I try with a kernel patched with the
> beta symbios driver ( 2.1.9 ), it works just fine.

Interesting.

Note that sym-2.1.9 status is probably far better than beta. I just
haven't information enough to know how reliable this driver version
actually is. FYI, I use sym-2.1.x under Linux and FreeBSD since several
months. The NetBSD port is still work in progress, but the driver works
just fine for me under this O/S too.

> This is on a Debian woody system, using cdrecord 1.10 ( also 1.9 and 1.8
> with the same symptoms ) attached to a Tekram DC390F.
>
> Transcript as follows :
>
> cdrecord dev=0,3,0 -dummy -xa2 firmware.iso
>
> Cdrecord 1.10a18 (i686-pc-linux-gnu) Copyright (C) 1995-2001 J?rg Schilling
> scsidev: '0,3,0'
> scsibus: 0 target: 3 lun: 0
> Linux sg driver version: 3.1.17
> Using libscg version 'schily-0.5'
> Device type : Removable CD-ROM
> Version : 2
> Response Format: 2
> Capabilities :
> Vendor_info : 'YAMAHA '
> Identifikation : 'CDR400t '
> Revision : '1.0q'
> Device seems to be: Yamaha CDR-400.
> Using generic SCSI-3/mmc CD-R driver (mmc_cdr).
> Driver flags : SWABAUDIO
> Starting to write CD/DVD at speed 1 in dummy mode for single session.
> Last chance to quit, starting dummy write in 1 seconds.
> cdrecord: Input/output error. write_g1: scsi sendcmd: retryable error
> CDB: 2A 00 00 00 01 C2 00 00 1F 00
> status: 0x0 (GOOD STATUS)
> DMA overrun, resid: -248

Would be interesting to know how cdrecord calculates the residual. It
should probably use the return value from read()/write(). Does it ?

> cmd finished after 0.579s timeout 40s
> write track data: error after 0 bytes
> Sense Bytes: 70 00 00 00 00 00 00 0A 00 00 00 00 00 00 00 00 00 00
>
>
> And while that lot happens, I get
>
> sym53c875-0-<3,*>: target did not report SYNC.

This message is not normal given the device that for sure supports
synchronous data transfers. I will look into this problem, first.

> sym53c875-0-<3,*>: extraneous data discarded.
> sym53c875-0-<3,*>: COMMAND FAILED (89 0) @c12a3800.

This one could have been triggerred by previous errors ???.

> Standard burns work ok, it's just the xa2 stuff I have a problem with so
> far. I also tried using the old NCR driver with the same results.

If you mean that the ncr53c8xx driver gets the same error, then the cause
can be a either common bug in sym53c8xx and ncr53c8xx, or caused by a
difference between sym53c8xx/ncr53c8xx and sym-2.1.9.

The main difference that comes to mind is that sym-2 uses the new error
handling interface but sym53c8xx/ncr53c8xx use the old one. If it is the
cause, then the sg driver might get involved in the failure.

> Anybody got any ideas?

No more than the above for now.
Will let you know if I get better ones.

Regards,
G?rard.