Replace hard-coded interrupt parts (GIC, flags) with standard defines
for readability. No changes in resulting DTBs. The comment was saying
interrupt was active low, but the actual used value was active high, so
assume that the code, not the comment, is correct.
Signed-off-by: Krzysztof Kozlowski <[email protected]>
---
arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi
index cc305e629bdc..040a48c88fab 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi
@@ -241,10 +241,10 @@ map0 {
timer: timer {
compatible = "arm,armv8-timer";
- interrupts = <1 13 4>, /* Physical Secure PPI, active-low */
- <1 14 4>, /* Physical Non-Secure PPI, active-low */
- <1 11 4>, /* Virtual PPI, active-low */
- <1 10 4>; /* Hypervisor PPI, active-low */
+ interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH>, /* Physical Secure PPI */
+ <GIC_PPI 14 IRQ_TYPE_LEVEL_HIGH>, /* Physical Non-Secure PPI */
+ <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>, /* Virtual PPI */
+ <GIC_PPI 10 IRQ_TYPE_LEVEL_HIGH>; /* Hypervisor PPI */
};
psci {
--
2.43.0
> Subject: [PATCH 2/3] arm64: dts: ls208xa: use defines for timer interrupts
>
> Replace hard-coded interrupt parts (GIC, flags) with standard defines for
> readability. No changes in resulting DTBs. The comment was saying interrupt
> was active low, but the actual used value was active high, so assume that the
> code, not the comment, is correct.
>
> Signed-off-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
> ---
> arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi | 8 ++++----
> 1 file changed, 4 insertions(+), 4 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi
> b/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi
> index cc305e629bdc..040a48c88fab 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi
> @@ -241,10 +241,10 @@ map0 {
>
> timer: timer {
> compatible = "arm,armv8-timer";
> - interrupts = <1 13 4>, /* Physical Secure PPI, active-low */
> - <1 14 4>, /* Physical Non-Secure PPI, active-low
> */
> - <1 11 4>, /* Virtual PPI, active-low */
> - <1 10 4>; /* Hypervisor PPI, active-low */
> + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH>, /* Physical
> Secure PPI */
> + <GIC_PPI 14 IRQ_TYPE_LEVEL_HIGH>, /* Physical
> Non-Secure PPI */
> + <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>, /* Virtual
> PPI */
> + <GIC_PPI 10 IRQ_TYPE_LEVEL_HIGH>; /*
> Hypervisor PPI */
> };
>
> psci {
> --
> 2.43.0
>