Now fsl_lpuart driver use both of_alias_get_id() and ida_simple_get() in
.probe(), which has the potential bug. For example, when remove the
lpuart7 alias in dts, of_alias_get_id() will return error, then call
ida_simple_get() to allocate the id 0 for lpuart7, this may confilct
with the lpuart4 which has alias 0.
aliases {
...
serial0 = &lpuart4;
serial1 = &lpuart5;
serial2 = &lpuart6;
serial3 = &lpuart7;
}
So remove the ida_simple_get() in .probe(), return an error directly
when calling of_alias_get_id() fails, which is consistent with other
uart drivers behavior.
Fixes: 3bc3206e1c0f ("serial: fsl_lpuart: Remove the alias node dependence")
Signed-off-by: Sherry Sun <[email protected]>
---
drivers/tty/serial/fsl_lpuart.c | 24 ++++--------------------
1 file changed, 4 insertions(+), 20 deletions(-)
diff --git a/drivers/tty/serial/fsl_lpuart.c b/drivers/tty/serial/fsl_lpuart.c
index 452a015825ba..40465d23d7ad 100644
--- a/drivers/tty/serial/fsl_lpuart.c
+++ b/drivers/tty/serial/fsl_lpuart.c
@@ -239,8 +239,6 @@
/* IMX lpuart has four extra unused regs located at the beginning */
#define IMX_REG_OFF 0x10
-static DEFINE_IDA(fsl_lpuart_ida);
-
enum lpuart_type {
VF610_LPUART,
LS1021A_LPUART,
@@ -276,7 +274,6 @@ struct lpuart_port {
int rx_dma_rng_buf_len;
unsigned int dma_tx_nents;
wait_queue_head_t dma_wait;
- bool id_allocated;
};
struct lpuart_soc_data {
@@ -2716,23 +2713,18 @@ static int lpuart_probe(struct platform_device *pdev)
ret = of_alias_get_id(np, "serial");
if (ret < 0) {
- ret = ida_simple_get(&fsl_lpuart_ida, 0, UART_NR, GFP_KERNEL);
- if (ret < 0) {
- dev_err(&pdev->dev, "port line is full, add device failed\n");
- return ret;
- }
- sport->id_allocated = true;
+ dev_err(&pdev->dev, "failed to get alias id, errno %d\n", ret);
+ return ret;
}
if (ret >= ARRAY_SIZE(lpuart_ports)) {
dev_err(&pdev->dev, "serial%d out of range\n", ret);
- ret = -EINVAL;
- goto failed_out_of_range;
+ return -EINVAL;
}
sport->port.line = ret;
ret = lpuart_enable_clks(sport);
if (ret)
- goto failed_clock_enable;
+ return ret;
sport->port.uartclk = lpuart_get_baud_clk_rate(sport);
lpuart_ports[sport->port.line] = sport;
@@ -2781,10 +2773,6 @@ static int lpuart_probe(struct platform_device *pdev)
failed_attach_port:
failed_irq_request:
lpuart_disable_clks(sport);
-failed_clock_enable:
-failed_out_of_range:
- if (sport->id_allocated)
- ida_simple_remove(&fsl_lpuart_ida, sport->port.line);
return ret;
}
@@ -2794,9 +2782,6 @@ static int lpuart_remove(struct platform_device *pdev)
uart_remove_one_port(&lpuart_reg, &sport->port);
- if (sport->id_allocated)
- ida_simple_remove(&fsl_lpuart_ida, sport->port.line);
-
lpuart_disable_clks(sport);
if (sport->dma_tx_chan)
@@ -2926,7 +2911,6 @@ static int __init lpuart_serial_init(void)
static void __exit lpuart_serial_exit(void)
{
- ida_destroy(&fsl_lpuart_ida);
platform_driver_unregister(&lpuart_driver);
uart_unregister_driver(&lpuart_reg);
}
--
2.17.1
> -----Original Message-----
> From: Sherry Sun <[email protected]>
> Sent: Monday, March 21, 2022 6:22 AM
> To: [email protected]; [email protected]; Vabhav Sharma
> <[email protected]>
> Cc: [email protected]; [email protected]; dl-linux-imx
> <[email protected]>
> Subject: [PATCH] tty: serial: fsl_lpuart: fix potential bug when using both
> of_alias_get_id and ida_simple_get
>
> Now fsl_lpuart driver use both of_alias_get_id() and ida_simple_get() in .probe(),
> which has the potential bug. For example, when remove the
> lpuart7 alias in dts, of_alias_get_id() will return error, then call
> ida_simple_get() to allocate the id 0 for lpuart7, this may confilct with the
> lpuart4 which has alias 0.
The behavior of ida_simple_get() is to allocate an unused alias number. Do you see any conflict when you test?
Regards,
Shenwei
>
> aliases {
> ...
> serial0 = &lpuart4;
> serial1 = &lpuart5;
> serial2 = &lpuart6;
> serial3 = &lpuart7;
> }
>
> So remove the ida_simple_get() in .probe(), return an error directly when calling
> of_alias_get_id() fails, which is consistent with other uart drivers behavior.
>
> Fixes: 3bc3206e1c0f ("serial: fsl_lpuart: Remove the alias node dependence")
> Signed-off-by: Sherry Sun <[email protected]>
> ---
> drivers/tty/serial/fsl_lpuart.c | 24 ++++--------------------
> 1 file changed, 4 insertions(+), 20 deletions(-)
>
> diff --git a/drivers/tty/serial/fsl_lpuart.c b/drivers/tty/serial/fsl_lpuart.c index
> 452a015825ba..40465d23d7ad 100644
> --- a/drivers/tty/serial/fsl_lpuart.c
> +++ b/drivers/tty/serial/fsl_lpuart.c
> @@ -239,8 +239,6 @@
> /* IMX lpuart has four extra unused regs located at the beginning */
> #define IMX_REG_OFF 0x10
>
> -static DEFINE_IDA(fsl_lpuart_ida);
> -
> enum lpuart_type {
> VF610_LPUART,
> LS1021A_LPUART,
> @@ -276,7 +274,6 @@ struct lpuart_port {
> int rx_dma_rng_buf_len;
> unsigned int dma_tx_nents;
> wait_queue_head_t dma_wait;
> - bool id_allocated;
> };
>
> struct lpuart_soc_data {
> @@ -2716,23 +2713,18 @@ static int lpuart_probe(struct platform_device
> *pdev)
>
> ret = of_alias_get_id(np, "serial");
> if (ret < 0) {
> - ret = ida_simple_get(&fsl_lpuart_ida, 0, UART_NR,
> GFP_KERNEL);
> - if (ret < 0) {
> - dev_err(&pdev->dev, "port line is full, add device
> failed\n");
> - return ret;
> - }
> - sport->id_allocated = true;
> + dev_err(&pdev->dev, "failed to get alias id, errno %d\n", ret);
> + return ret;
> }
> if (ret >= ARRAY_SIZE(lpuart_ports)) {
> dev_err(&pdev->dev, "serial%d out of range\n", ret);
> - ret = -EINVAL;
> - goto failed_out_of_range;
> + return -EINVAL;
> }
> sport->port.line = ret;
>
> ret = lpuart_enable_clks(sport);
> if (ret)
> - goto failed_clock_enable;
> + return ret;
> sport->port.uartclk = lpuart_get_baud_clk_rate(sport);
>
> lpuart_ports[sport->port.line] = sport; @@ -2781,10 +2773,6 @@ static
> int lpuart_probe(struct platform_device *pdev)
> failed_attach_port:
> failed_irq_request:
> lpuart_disable_clks(sport);
> -failed_clock_enable:
> -failed_out_of_range:
> - if (sport->id_allocated)
> - ida_simple_remove(&fsl_lpuart_ida, sport->port.line);
> return ret;
> }
>
> @@ -2794,9 +2782,6 @@ static int lpuart_remove(struct platform_device
> *pdev)
>
> uart_remove_one_port(&lpuart_reg, &sport->port);
>
> - if (sport->id_allocated)
> - ida_simple_remove(&fsl_lpuart_ida, sport->port.line);
> -
> lpuart_disable_clks(sport);
>
> if (sport->dma_tx_chan)
> @@ -2926,7 +2911,6 @@ static int __init lpuart_serial_init(void)
>
> static void __exit lpuart_serial_exit(void) {
> - ida_destroy(&fsl_lpuart_ida);
> platform_driver_unregister(&lpuart_driver);
> uart_unregister_driver(&lpuart_reg);
> }
> --
> 2.17.1
Hi Shenwei,
> > Subject: [PATCH] tty: serial: fsl_lpuart: fix potential bug when using
> > both of_alias_get_id and ida_simple_get
> >
> > Now fsl_lpuart driver use both of_alias_get_id() and ida_simple_get()
> > in .probe(), which has the potential bug. For example, when remove the
> > lpuart7 alias in dts, of_alias_get_id() will return error, then call
> > ida_simple_get() to allocate the id 0 for lpuart7, this may confilct
> > with the
> > lpuart4 which has alias 0.
>
> The behavior of ida_simple_get() is to allocate an unused alias number. Do
> you see any conflict when you test?
>
Yes, I have verified this on imx8ulp, I print the port.line value for each uart port.
When I remove the lpuart7 alias, the lpuart7 will get the id 0, same as lpuart4, which caused the lpuart7 probe fail.
ida_simple_get() cannot figure out which id has been used in the uart driver.
[ 0.894549] port.line = 0 --> lpuart4
[ 0.908148] port.line = 1 --> lpuart5
[ 0.939844] port.line = 2 --> lpuart6
[ 0.953608] port.line = 0 --> lpuart7
--- a/arch/arm64/boot/dts/freescale/imx8ulp.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8ulp.dtsi
@@ -25,7 +25,6 @@
serial0 = &lpuart4;
serial1 = &lpuart5;
serial2 = &lpuart6;
- serial3 = &lpuart7;
};
Best regards
Sherry
> Regards,
> Shenwei
>
> >
> > aliases {
> > ...
> > serial0 = &lpuart4;
> > serial1 = &lpuart5;
> > serial2 = &lpuart6;
> > serial3 = &lpuart7;
> > }
> >
> > So remove the ida_simple_get() in .probe(), return an error directly
> > when calling
> > of_alias_get_id() fails, which is consistent with other uart drivers behavior.
> >
> > Fixes: 3bc3206e1c0f ("serial: fsl_lpuart: Remove the alias node
> > dependence")
> > Signed-off-by: Sherry Sun <[email protected]>
> > ---
> > drivers/tty/serial/fsl_lpuart.c | 24 ++++--------------------
> > 1 file changed, 4 insertions(+), 20 deletions(-)
> >
> > diff --git a/drivers/tty/serial/fsl_lpuart.c
> > b/drivers/tty/serial/fsl_lpuart.c index 452a015825ba..40465d23d7ad
> > 100644
> > --- a/drivers/tty/serial/fsl_lpuart.c
> > +++ b/drivers/tty/serial/fsl_lpuart.c
> > @@ -239,8 +239,6 @@
> > /* IMX lpuart has four extra unused regs located at the beginning */
> > #define IMX_REG_OFF 0x10
> >
> > -static DEFINE_IDA(fsl_lpuart_ida);
> > -
> > enum lpuart_type {
> > VF610_LPUART,
> > LS1021A_LPUART,
> > @@ -276,7 +274,6 @@ struct lpuart_port {
> > int rx_dma_rng_buf_len;
> > unsigned int dma_tx_nents;
> > wait_queue_head_t dma_wait;
> > - bool id_allocated;
> > };
> >
> > struct lpuart_soc_data {
> > @@ -2716,23 +2713,18 @@ static int lpuart_probe(struct platform_device
> > *pdev)
> >
> > ret = of_alias_get_id(np, "serial");
> > if (ret < 0) {
> > - ret = ida_simple_get(&fsl_lpuart_ida, 0, UART_NR,
> > GFP_KERNEL);
> > - if (ret < 0) {
> > - dev_err(&pdev->dev, "port line is full, add device
> > failed\n");
> > - return ret;
> > - }
> > - sport->id_allocated = true;
> > + dev_err(&pdev->dev, "failed to get alias id, errno %d\n", ret);
> > + return ret;
> > }
> > if (ret >= ARRAY_SIZE(lpuart_ports)) {
> > dev_err(&pdev->dev, "serial%d out of range\n", ret);
> > - ret = -EINVAL;
> > - goto failed_out_of_range;
> > + return -EINVAL;
> > }
> > sport->port.line = ret;
> >
> > ret = lpuart_enable_clks(sport);
> > if (ret)
> > - goto failed_clock_enable;
> > + return ret;
> > sport->port.uartclk = lpuart_get_baud_clk_rate(sport);
> >
> > lpuart_ports[sport->port.line] = sport; @@ -2781,10 +2773,6 @@
> > static int lpuart_probe(struct platform_device *pdev)
> > failed_attach_port:
> > failed_irq_request:
> > lpuart_disable_clks(sport);
> > -failed_clock_enable:
> > -failed_out_of_range:
> > - if (sport->id_allocated)
> > - ida_simple_remove(&fsl_lpuart_ida, sport->port.line);
> > return ret;
> > }
> >
> > @@ -2794,9 +2782,6 @@ static int lpuart_remove(struct platform_device
> > *pdev)
> >
> > uart_remove_one_port(&lpuart_reg, &sport->port);
> >
> > - if (sport->id_allocated)
> > - ida_simple_remove(&fsl_lpuart_ida, sport->port.line);
> > -
> > lpuart_disable_clks(sport);
> >
> > if (sport->dma_tx_chan)
> > @@ -2926,7 +2911,6 @@ static int __init lpuart_serial_init(void)
> >
> > static void __exit lpuart_serial_exit(void) {
> > - ida_destroy(&fsl_lpuart_ida);
> > platform_driver_unregister(&lpuart_driver);
> > uart_unregister_driver(&lpuart_reg);
> > }
> > --
> > 2.17.1
Gentle ping...
> -----Original Message-----
> From: Sherry Sun
> Sent: 2022??3??21?? 19:25
> To: [email protected]; [email protected]; Vabhav Sharma
> <[email protected]>
> Cc: [email protected]; [email protected]; dl-linux-imx
> <[email protected]>
> Subject: [PATCH] tty: serial: fsl_lpuart: fix potential bug when using both
> of_alias_get_id and ida_simple_get
>
> Now fsl_lpuart driver use both of_alias_get_id() and ida_simple_get()
> in .probe(), which has the potential bug. For example, when remove the
> lpuart7 alias in dts, of_alias_get_id() will return error, then call
> ida_simple_get() to allocate the id 0 for lpuart7, this may confilct with the
> lpuart4 which has alias 0.
>
> aliases {
> ...
> serial0 = &lpuart4;
> serial1 = &lpuart5;
> serial2 = &lpuart6;
> serial3 = &lpuart7;
> }
>
> So remove the ida_simple_get() in .probe(), return an error directly when
> calling of_alias_get_id() fails, which is consistent with other uart drivers
> behavior.
>
> Fixes: 3bc3206e1c0f ("serial: fsl_lpuart: Remove the alias node dependence")
> Signed-off-by: Sherry Sun <[email protected]>
> ---
> drivers/tty/serial/fsl_lpuart.c | 24 ++++--------------------
> 1 file changed, 4 insertions(+), 20 deletions(-)
>
> diff --git a/drivers/tty/serial/fsl_lpuart.c b/drivers/tty/serial/fsl_lpuart.c
> index 452a015825ba..40465d23d7ad 100644
> --- a/drivers/tty/serial/fsl_lpuart.c
> +++ b/drivers/tty/serial/fsl_lpuart.c
> @@ -239,8 +239,6 @@
> /* IMX lpuart has four extra unused regs located at the beginning */
> #define IMX_REG_OFF 0x10
>
> -static DEFINE_IDA(fsl_lpuart_ida);
> -
> enum lpuart_type {
> VF610_LPUART,
> LS1021A_LPUART,
> @@ -276,7 +274,6 @@ struct lpuart_port {
> int rx_dma_rng_buf_len;
> unsigned int dma_tx_nents;
> wait_queue_head_t dma_wait;
> - bool id_allocated;
> };
>
> struct lpuart_soc_data {
> @@ -2716,23 +2713,18 @@ static int lpuart_probe(struct platform_device
> *pdev)
>
> ret = of_alias_get_id(np, "serial");
> if (ret < 0) {
> - ret = ida_simple_get(&fsl_lpuart_ida, 0, UART_NR,
> GFP_KERNEL);
> - if (ret < 0) {
> - dev_err(&pdev->dev, "port line is full, add device
> failed\n");
> - return ret;
> - }
> - sport->id_allocated = true;
> + dev_err(&pdev->dev, "failed to get alias id, errno %d\n", ret);
> + return ret;
> }
> if (ret >= ARRAY_SIZE(lpuart_ports)) {
> dev_err(&pdev->dev, "serial%d out of range\n", ret);
> - ret = -EINVAL;
> - goto failed_out_of_range;
> + return -EINVAL;
> }
> sport->port.line = ret;
>
> ret = lpuart_enable_clks(sport);
> if (ret)
> - goto failed_clock_enable;
> + return ret;
> sport->port.uartclk = lpuart_get_baud_clk_rate(sport);
>
> lpuart_ports[sport->port.line] = sport; @@ -2781,10 +2773,6 @@
> static int lpuart_probe(struct platform_device *pdev)
> failed_attach_port:
> failed_irq_request:
> lpuart_disable_clks(sport);
> -failed_clock_enable:
> -failed_out_of_range:
> - if (sport->id_allocated)
> - ida_simple_remove(&fsl_lpuart_ida, sport->port.line);
> return ret;
> }
>
> @@ -2794,9 +2782,6 @@ static int lpuart_remove(struct platform_device
> *pdev)
>
> uart_remove_one_port(&lpuart_reg, &sport->port);
>
> - if (sport->id_allocated)
> - ida_simple_remove(&fsl_lpuart_ida, sport->port.line);
> -
> lpuart_disable_clks(sport);
>
> if (sport->dma_tx_chan)
> @@ -2926,7 +2911,6 @@ static int __init lpuart_serial_init(void)
>
> static void __exit lpuart_serial_exit(void) {
> - ida_destroy(&fsl_lpuart_ida);
> platform_driver_unregister(&lpuart_driver);
> uart_unregister_driver(&lpuart_reg);
> }
> --
> 2.17.1
Hi Greg,
> Subject: Re: [PATCH] tty: serial: fsl_lpuart: fix potential bug when using both
> of_alias_get_id and ida_simple_get
>
> On Fri, Mar 25, 2022 at 01:27:05AM +0000, Sherry Sun wrote:
> > Gentle ping...
>
> It is the middle of the merge window. I can't do anything with new
> changes until after 5.18-rc1 is out. Please wait until then.
>
> In the meantime, please help out by reviewing other pending patches from
> the mailing list.
Got it, thanks for the info.
Best regards
Sherry
>
> thanks!
>
> greg k-h
On Fri, Mar 25, 2022 at 01:27:05AM +0000, Sherry Sun wrote:
> Gentle ping...
It is the middle of the merge window. I can't do anything with new
changes until after 5.18-rc1 is out. Please wait until then.
In the meantime, please help out by reviewing other pending patches from
the mailing list.
thanks!
greg k-h