Sekhar,
On Mon, Feb 4, 2013 at 10:33 AM, Prabhakar Lad
<[email protected]> wrote:
> Sekhar ,
>
> On Sun, Feb 3, 2013 at 6:15 PM, Sekhar Nori <[email protected]> wrote:
>> On 1/28/2013 7:17 PM, Prabhakar Lad wrote:
>>> From: Lad, Prabhakar <[email protected]>
>>>
>>> The system configuration chip CFGCHIP3, controls the emac module.
>>> This patch appropriately configures this register for emac and
>>> sets DA850_MII_MDIO_CLKEN_PIN GPIO pin appropriately.
>>>
>>> Signed-off-by: Lad, Prabhakar <[email protected]>
>>> Cc: [email protected]
>>> Cc: [email protected]
>>> Cc: [email protected]
>>> Cc: [email protected]
>>> Cc: [email protected]
>>> Cc: Sekhar Nori <[email protected]>
>>> Cc: Heiko Schocher <[email protected]>
>>> ---
>>> arch/arm/mach-davinci/da8xx-dt.c | 28 ++++++++++++++++++++++++++++
>>> 1 files changed, 28 insertions(+), 0 deletions(-)
>>>
>>> diff --git a/arch/arm/mach-davinci/da8xx-dt.c b/arch/arm/mach-davinci/da8xx-dt.c
>>> index e533a0a..4a096e3 100644
>>> --- a/arch/arm/mach-davinci/da8xx-dt.c
>>> +++ b/arch/arm/mach-davinci/da8xx-dt.c
>>> @@ -8,6 +8,7 @@
>>> * published by the Free Software Foundation.
>>> */
>>> #include <linux/io.h>
>>> +#include <linux/gpio.h>
>>> #include <linux/of_irq.h>
>>> #include <linux/of_platform.h>
>>> #include <linux/irqdomain.h>
>>> @@ -39,6 +40,32 @@ static void __init da8xx_init_irq(void)
>>>
>>> #ifdef CONFIG_ARCH_DAVINCI_DA850
>>>
>>> +static void __init da8xx_config_emac(void)
>>> +{
>>> +#define DA850_MII_MDIO_CLKEN_PIN GPIO_TO_PIN(2, 6)
>>> +#define DA850_EMAC_MODE_SELECT BIT(8)
>>> + void __iomem *cfg_chip3_base;
>>> + int ret;
>>> + u32 val;
>>> +
>>> + cfg_chip3_base = DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP3_REG);
>>> +
>>> + val = __raw_readl(cfg_chip3_base);
>>> + val &= ~DA850_EMAC_MODE_SELECT;
>>> + /* configure the CFGCHIP3 register for MII */
>>> + __raw_writel(val, cfg_chip3_base);
>>
>> Use readl/writel instead.
>>
> Ok.
>
>>> + pr_info("EMAC: MII PHY configured\n");
>>> +
>>> + ret = gpio_request(DA850_MII_MDIO_CLKEN_PIN, "mdio_clk_en");
>>> + if (ret) {
>>> + pr_warn("Cannot open GPIO %d\n",
>>> + DA850_MII_MDIO_CLKEN_PIN);
>>> + return;
>>> + }
>>> + /* Enable/Disable MII MDIO clock */
>>> + gpio_direction_output(DA850_MII_MDIO_CLKEN_PIN, 0);
>>> +}
>>> +
>>> struct of_dev_auxdata da8xx_auxdata[] __initdata = {
>>> OF_DEV_AUXDATA("ti,davinci_mdio", 0x01e24000, "davinci_mdio.0", NULL),
>>> OF_DEV_AUXDATA("ti,davinci-dm6467-emac", 0x01e20000, "davinci_emac.1",
>>> @@ -52,6 +79,7 @@ static void __init da850_init_machine(void)
>>> da8xx_auxdata, NULL);
>>>
>>> da8xx_uart_clk_enable();
>>> + da8xx_config_emac();
>>
>> There are couple of issues with this implementation.
>>
>> 1) da8xx_config_emac() is specific to DA850 EVM, but masquerades as
>> generic for da8xx. Looks like you need two functions, one for soc
>> specific configuration and one board specific.
> Ok.
>
>> 2) da8xx_config_emac() goes through all the time, whether the
>> particular board has emac module or not. Shouldn't
>> da8xx_config_emac() check if emac is actually enabled in the passed
>> dtb and only the do the configuration?
>
> Ok. Can you give some pointers how we can access the dtb in board files.
>
Any pointers on this could be helpful.
Regards,
--Prabhakar
>> 3) The function assumes mii is used always, you can use the rmii_en dt
>> property to check if rmii/mii is enabled and configure the soc/board
>> accordingly.
>
> Ok.
>
>> 4) If the same function can work both for da850 and da830, then it can
>> be implemented outside of CONFIG_ARCH_DAVINCI_DA850.
>>
> Ok.
>
> Regards,
> --Prabhakar
>
>> Thanks,
>> Sekhar