On Sat, Dec 14, 2013 at 12:14 AM, Christian Daudt <[email protected]> wrote:
> On Thu, Dec 5, 2013 at 11:20 AM, Tim Kryger <[email protected]> wrote:
>> Enable the external clock needed by the host controller during the
>> probe and disable it during the remove.
>>
>> Signed-off-by: Tim Kryger <[email protected]>
>> Reviewed-by: Markus Mayer <[email protected]>
>> Reviewed-by: Matt Porter <[email protected]>
>
> Reviewed-by: Christian Daudt <[email protected]>
>
> Chris,
> Are you ok with me pulling this patch along with the rest of the
> patchset into the bcm tree?
>
> Thanks,
> csd
Chris,
Can you please provide an answer to csd?
Thanks,
Tim Kryger
On Tue, Jan 7, 2014 at 11:37 AM, Tim Kryger <[email protected]> wrote:
> On Sat, Dec 14, 2013 at 12:14 AM, Christian Daudt <[email protected]> wrote:
>> On Thu, Dec 5, 2013 at 11:20 AM, Tim Kryger <[email protected]> wrote:
>>> Enable the external clock needed by the host controller during the
>>> probe and disable it during the remove.
>>>
>>> Signed-off-by: Tim Kryger <[email protected]>
>>> Reviewed-by: Markus Mayer <[email protected]>
>>> Reviewed-by: Matt Porter <[email protected]>
>>
>> Reviewed-by: Christian Daudt <[email protected]>
>>
>> Chris,
>> Are you ok with me pulling this patch along with the rest of the
>> patchset into the bcm tree?
>>
>> Thanks,
>> csd
>
> Chris,
>
> Can you please provide an answer to csd?
>
> Thanks,
> Tim Kryger
Chris,
I haven't heard back so this patch has been dropped for 3.14 to allow
the remaining patches in the series to move forward. As such, I will
be re-posting this patch for 3.15. It is essential for the
bcm28155_ap board to transition away from fake fixed clocks to the
real clock driver. This is because the bcm281xx clock driver does not
set the CLK_IGNORE_UNUSED flag for the SDHCI peripheral clocks and the
common clock code will shut them off in late init unless the SDHCI
driver has asked for them to be enabled.
Thanks,
Tim
[trimmed cc]
On Fri, Jan 24, 2014 at 09:07:24AM -0800, Tim Kryger wrote:
> On Tue, Jan 7, 2014 at 11:37 AM, Tim Kryger <[email protected]> wrote:
> > On Sat, Dec 14, 2013 at 12:14 AM, Christian Daudt <[email protected]> wrote:
> >> On Thu, Dec 5, 2013 at 11:20 AM, Tim Kryger <[email protected]> wrote:
> >>> Enable the external clock needed by the host controller during the
> >>> probe and disable it during the remove.
> >>>
> >>> Signed-off-by: Tim Kryger <[email protected]>
> >>> Reviewed-by: Markus Mayer <[email protected]>
> >>> Reviewed-by: Matt Porter <[email protected]>
> >>
> >> Reviewed-by: Christian Daudt <[email protected]>
> >>
> >> Chris,
> >> Are you ok with me pulling this patch along with the rest of the
> >> patchset into the bcm tree?
> >>
> >> Thanks,
> >> csd
> >
> > Chris,
> >
> > Can you please provide an answer to csd?
> >
> > Thanks,
> > Tim Kryger
>
> Chris,
>
> I haven't heard back so this patch has been dropped for 3.14 to allow
> the remaining patches in the series to move forward. As such, I will
> be re-posting this patch for 3.15. It is essential for the
> bcm28155_ap board to transition away from fake fixed clocks to the
> real clock driver. This is because the bcm281xx clock driver does not
> set the CLK_IGNORE_UNUSED flag for the SDHCI peripheral clocks and the
> common clock code will shut them off in late init unless the SDHCI
> driver has asked for them to be enabled.
I just queued Alex's patch for 3.15 that decouples the dependency
between this patch and the bcm kona common clock driver.
Chris: we no longer need this to be taken through arm-soc since removing
the dependency. Could you please take this patch through your tree for
3.15?
Thanks,
Matt
Hi,
On Mon, Feb 24 2014, Matt Porter wrote:
> Chris: we no longer need this to be taken through arm-soc since removing
> the dependency. Could you please take this patch through your tree for
> 3.15?
Thanks, pushed to mmc-next for 3.15.
- Chris.
--
Chris Ball <[email protected]> <http://printf.net/>