2020-06-05 17:10:33

by Álvaro Fernández Rojas

[permalink] [raw]
Subject: [PATCH] mtd: rawnand: brcmnand: force raw OOB writes

MTD_OPS_AUTO_OOB is writting OOB with ECC enabled, which changes all ECC bytes
from an erased page to 0x00 when JFFS2 cleanmarkers are added with mtd-utils.
| BBI | JFFS2 | ECC | JFFS2 | Spare |
00000800 ff ff 19 85 20 03 00 00 00 00 00 00 08 ff ff ff

However, if OOB is written with ECC disabled, the JFFS2 cleanmarkers are
correctly written without changing the ECC bytes:
| BBI | JFFS2 | ECC | JFFS2 | Spare |
00000800 ff ff 19 85 20 03 ff ff ff 00 00 00 08 ff ff ff

Signed-off-by: Álvaro Fernández Rojas <[email protected]>
---
drivers/mtd/nand/raw/brcmnand/brcmnand.c | 9 +--------
1 file changed, 1 insertion(+), 8 deletions(-)

diff --git a/drivers/mtd/nand/raw/brcmnand/brcmnand.c b/drivers/mtd/nand/raw/brcmnand/brcmnand.c
index 8f9ffb46a09f..566281770841 100644
--- a/drivers/mtd/nand/raw/brcmnand/brcmnand.c
+++ b/drivers/mtd/nand/raw/brcmnand/brcmnand.c
@@ -2279,13 +2279,6 @@ static int brcmnand_write_page_raw(struct nand_chip *chip, const uint8_t *buf,
return nand_prog_page_end_op(chip);
}

-static int brcmnand_write_oob(struct nand_chip *chip, int page)
-{
- return brcmnand_write(nand_to_mtd(chip), chip,
- (u64)page << chip->page_shift, NULL,
- chip->oob_poi);
-}
-
static int brcmnand_write_oob_raw(struct nand_chip *chip, int page)
{
struct mtd_info *mtd = nand_to_mtd(chip);
@@ -2642,7 +2635,7 @@ static int brcmnand_init_cs(struct brcmnand_host *host, struct device_node *dn)
chip->ecc.write_oob_raw = brcmnand_write_oob_raw;
chip->ecc.read_oob_raw = brcmnand_read_oob_raw;
chip->ecc.read_oob = brcmnand_read_oob;
- chip->ecc.write_oob = brcmnand_write_oob;
+ chip->ecc.write_oob = brcmnand_write_oob_raw;

chip->controller = &ctrl->controller;

--
2.26.2


2020-06-12 18:52:13

by Kamal Dasu

[permalink] [raw]
Subject: Re: [PATCH] mtd: rawnand: brcmnand: force raw OOB writes

On Fri, Jun 5, 2020 at 1:07 PM Álvaro Fernández Rojas <[email protected]> wrote:
>
> MTD_OPS_AUTO_OOB is writting OOB with ECC enabled, which changes all ECC bytes
> from an erased page to 0x00 when JFFS2 cleanmarkers are added with mtd-utils.
> | BBI | JFFS2 | ECC | JFFS2 | Spare |
> 00000800 ff ff 19 85 20 03 00 00 00 00 00 00 08 ff ff ff
>
> However, if OOB is written with ECC disabled, the JFFS2 cleanmarkers are
> correctly written without changing the ECC bytes:
> | BBI | JFFS2 | ECC | JFFS2 | Spare |
> 00000800 ff ff 19 85 20 03 ff ff ff 00 00 00 08 ff ff ff

Both brcmand_write_oob_raw() and brcmnand_write_oob() use
brcmnand_write() that uses PROGRAM_PAGE cmd, means also programs data
areas and ECC when enabled is always calculated on DATA+OOB. since
in both cases we only want to modify OOB, data is always assumed to be
0xffs (means erased state). So as far as this api always is used on
the erased page it should be good. Are the sub-pages/oob areas read by
jffs2 also read without ecc enabled?. Just want to be sure that it
does not break any other utilities like nandwrite.

>
> Signed-off-by: Álvaro Fernández Rojas <[email protected]>
> ---
> drivers/mtd/nand/raw/brcmnand/brcmnand.c | 9 +--------
> 1 file changed, 1 insertion(+), 8 deletions(-)
>
> diff --git a/drivers/mtd/nand/raw/brcmnand/brcmnand.c b/drivers/mtd/nand/raw/brcmnand/brcmnand.c
> index 8f9ffb46a09f..566281770841 100644
> --- a/drivers/mtd/nand/raw/brcmnand/brcmnand.c
> +++ b/drivers/mtd/nand/raw/brcmnand/brcmnand.c
> @@ -2279,13 +2279,6 @@ static int brcmnand_write_page_raw(struct nand_chip *chip, const uint8_t *buf,
> return nand_prog_page_end_op(chip);
> }
>
> -static int brcmnand_write_oob(struct nand_chip *chip, int page)
> -{
> - return brcmnand_write(nand_to_mtd(chip), chip,
> - (u64)page << chip->page_shift, NULL,
> - chip->oob_poi);
> -}
> -
> static int brcmnand_write_oob_raw(struct nand_chip *chip, int page)
> {
> struct mtd_info *mtd = nand_to_mtd(chip);
> @@ -2642,7 +2635,7 @@ static int brcmnand_init_cs(struct brcmnand_host *host, struct device_node *dn)
> chip->ecc.write_oob_raw = brcmnand_write_oob_raw;
> chip->ecc.read_oob_raw = brcmnand_read_oob_raw;
> chip->ecc.read_oob = brcmnand_read_oob;
> - chip->ecc.write_oob = brcmnand_write_oob;
> + chip->ecc.write_oob = brcmnand_write_oob_raw;
>
> chip->controller = &ctrl->controller;
>
> --
> 2.26.2
>

2020-06-13 09:09:45

by Álvaro Fernández Rojas

[permalink] [raw]
Subject: Re: [PATCH] mtd: rawnand: brcmnand: force raw OOB writes

Hi Kamal,

> El 12 jun 2020, a las 20:47, Kamal Dasu <[email protected]> escribió:
>
> On Fri, Jun 5, 2020 at 1:07 PM Álvaro Fernández Rojas <[email protected]> wrote:
>>
>> MTD_OPS_AUTO_OOB is writting OOB with ECC enabled, which changes all ECC bytes
>> from an erased page to 0x00 when JFFS2 cleanmarkers are added with mtd-utils.
>> | BBI | JFFS2 | ECC | JFFS2 | Spare |
>> 00000800 ff ff 19 85 20 03 00 00 00 00 00 00 08 ff ff ff
>>
>> However, if OOB is written with ECC disabled, the JFFS2 cleanmarkers are
>> correctly written without changing the ECC bytes:
>> | BBI | JFFS2 | ECC | JFFS2 | Spare |
>> 00000800 ff ff 19 85 20 03 ff ff ff 00 00 00 08 ff ff ff
>
> Both brcmand_write_oob_raw() and brcmnand_write_oob() use
> brcmnand_write() that uses PROGRAM_PAGE cmd, means also programs data
> areas and ECC when enabled is always calculated on DATA+OOB. since

Are you sure about that? I think that HW ECC is only calculated for DATA, not for OOB.
The fact that we’re not writing any DATA seems to be the problem that is changing all ECC bytes to 0x00.

> in both cases we only want to modify OOB, data is always assumed to be
> 0xffs (means erased state). So as far as this api always is used on
> the erased page it should be good. Are the sub-pages/oob areas read by
> jffs2 also read without ecc enabled?. Just want to be sure that it
> does not break any other utilities like nandwrite.

No, sub-pages/oob areas read by JFFS2 with ECC enabled.
I don’t think this breaks anything at all, since I tested nandwrite with OOB enabled and everything was written perfectly.

BTW, I tried another approach that forced MTD_OPS_AUTO_OOB to be written as raw OOB, but it was rejected:
http://patchwork.ozlabs.org/project/linux-mtd/patch/[email protected]/
https://lkml.org/lkml/2020/5/4/215

>
>>
>> Signed-off-by: Álvaro Fernández Rojas <[email protected]>
>> ---
>> drivers/mtd/nand/raw/brcmnand/brcmnand.c | 9 +--------
>> 1 file changed, 1 insertion(+), 8 deletions(-)
>>
>> diff --git a/drivers/mtd/nand/raw/brcmnand/brcmnand.c b/drivers/mtd/nand/raw/brcmnand/brcmnand.c
>> index 8f9ffb46a09f..566281770841 100644
>> --- a/drivers/mtd/nand/raw/brcmnand/brcmnand.c
>> +++ b/drivers/mtd/nand/raw/brcmnand/brcmnand.c
>> @@ -2279,13 +2279,6 @@ static int brcmnand_write_page_raw(struct nand_chip *chip, const uint8_t *buf,
>> return nand_prog_page_end_op(chip);
>> }
>>
>> -static int brcmnand_write_oob(struct nand_chip *chip, int page)
>> -{
>> - return brcmnand_write(nand_to_mtd(chip), chip,
>> - (u64)page << chip->page_shift, NULL,
>> - chip->oob_poi);
>> -}
>> -
>> static int brcmnand_write_oob_raw(struct nand_chip *chip, int page)
>> {
>> struct mtd_info *mtd = nand_to_mtd(chip);
>> @@ -2642,7 +2635,7 @@ static int brcmnand_init_cs(struct brcmnand_host *host, struct device_node *dn)
>> chip->ecc.write_oob_raw = brcmnand_write_oob_raw;
>> chip->ecc.read_oob_raw = brcmnand_read_oob_raw;
>> chip->ecc.read_oob = brcmnand_read_oob;
>> - chip->ecc.write_oob = brcmnand_write_oob;
>> + chip->ecc.write_oob = brcmnand_write_oob_raw;
>>
>> chip->controller = &ctrl->controller;
>>
>> --
>> 2.26.2
>>

Best regards,
Álvaro.

2020-06-13 15:19:19

by Kamal Dasu

[permalink] [raw]
Subject: Re: [PATCH] mtd: rawnand: brcmnand: force raw OOB writes

Alvaro,


On Sat, Jun 13, 2020 at 5:01 AM Álvaro Fernández Rojas
<[email protected]> wrote:
>
> Hi Kamal,
>
> > El 12 jun 2020, a las 20:47, Kamal Dasu <[email protected]> escribió:
> >
> > On Fri, Jun 5, 2020 at 1:07 PM Álvaro Fernández Rojas <[email protected]> wrote:
> >>
> >> MTD_OPS_AUTO_OOB is writting OOB with ECC enabled, which changes all ECC bytes
> >> from an erased page to 0x00 when JFFS2 cleanmarkers are added with mtd-utils.
> >> | BBI | JFFS2 | ECC | JFFS2 | Spare |
> >> 00000800 ff ff 19 85 20 03 00 00 00 00 00 00 08 ff ff ff
> >>
> >> However, if OOB is written with ECC disabled, the JFFS2 cleanmarkers are
> >> correctly written without changing the ECC bytes:
> >> | BBI | JFFS2 | ECC | JFFS2 | Spare |
> >> 00000800 ff ff 19 85 20 03 ff ff ff 00 00 00 08 ff ff ff
> >
> > Both brcmand_write_oob_raw() and brcmnand_write_oob() use
> > brcmnand_write() that uses PROGRAM_PAGE cmd, means also programs data
> > areas and ECC when enabled is always calculated on DATA+OOB. since
>
> Are you sure about that? I think that HW ECC is only calculated for DATA, not for OOB.
> The fact that we’re not writing any DATA seems to be the problem that is changing all ECC bytes to 0x00.
>

Only true for 1-bit hamming code on early controller versions. For
BCH algorithms both data+oob are covered. And the controller driver
intentionally does not implement a spare area program cmd, even for
OOB writes. Also BRCMNAND_ACC_CONTROL_PARTIAL_PAGE=0 (when present)
does not allow for spare areas only writes.

> > in both cases we only want to modify OOB, data is always assumed to be
> > 0xffs (means erased state). So as far as this api always is used on
> > the erased page it should be good. Are the sub-pages/oob areas read by
> > jffs2 also read without ecc enabled?. Just want to be sure that it
> > does not break any other utilities like nandwrite.
>
> No, sub-pages/oob areas read by JFFS2 with ECC enabled.
> I don’t think this breaks anything at all, since I tested nandwrite with OOB enabled and everything was written perfectly.
>

Going by the commit message you are assuming 1-bit hamming code, that
is the only exception on early version controllers where only data was
covered for ecc calculations when enabled.
Which version of the controller are you using ?. Did you test with
BCH-4 or any BCH ?.

> BTW, I tried another approach that forced MTD_OPS_AUTO_OOB to be written as raw OOB, but it was rejected:
> http://patchwork.ozlabs.org/project/linux-mtd/patch/[email protected]/
> https://lkml.org/lkml/2020/5/4/215
>

Are there any other use cases other than jffs2 where only oob needs to
be modified ?. But surely intentionally disabling ecc instead of
forcing it is the way, but I am not sure it will still work for other
BCH algorithms though where both data and oob are covered.

> >
> >>
> >> Signed-off-by: Álvaro Fernández Rojas <[email protected]>
> >> ---
> >> drivers/mtd/nand/raw/brcmnand/brcmnand.c | 9 +--------
> >> 1 file changed, 1 insertion(+), 8 deletions(-)
> >>
> >> diff --git a/drivers/mtd/nand/raw/brcmnand/brcmnand.c b/drivers/mtd/nand/raw/brcmnand/brcmnand.c
> >> index 8f9ffb46a09f..566281770841 100644
> >> --- a/drivers/mtd/nand/raw/brcmnand/brcmnand.c
> >> +++ b/drivers/mtd/nand/raw/brcmnand/brcmnand.c
> >> @@ -2279,13 +2279,6 @@ static int brcmnand_write_page_raw(struct nand_chip *chip, const uint8_t *buf,
> >> return nand_prog_page_end_op(chip);
> >> }
> >>
> >> -static int brcmnand_write_oob(struct nand_chip *chip, int page)
> >> -{
> >> - return brcmnand_write(nand_to_mtd(chip), chip,
> >> - (u64)page << chip->page_shift, NULL,
> >> - chip->oob_poi);
> >> -}
> >> -
> >> static int brcmnand_write_oob_raw(struct nand_chip *chip, int page)
> >> {
> >> struct mtd_info *mtd = nand_to_mtd(chip);
> >> @@ -2642,7 +2635,7 @@ static int brcmnand_init_cs(struct brcmnand_host *host, struct device_node *dn)
> >> chip->ecc.write_oob_raw = brcmnand_write_oob_raw;
> >> chip->ecc.read_oob_raw = brcmnand_read_oob_raw;
> >> chip->ecc.read_oob = brcmnand_read_oob;
> >> - chip->ecc.write_oob = brcmnand_write_oob;
> >> + chip->ecc.write_oob = brcmnand_write_oob_raw;
> >>
> >> chip->controller = &ctrl->controller;
> >>
> >> --
> >> 2.26.2
> >>
>
> Best regards,
> Álvaro.

2020-06-14 08:56:19

by Álvaro Fernández Rojas

[permalink] [raw]
Subject: Re: [PATCH] mtd: rawnand: brcmnand: force raw OOB writes

Hi Kamal,

> El 13 jun 2020, a las 17:16, Kamal Dasu <[email protected]> escribió:
>
> Alvaro,
>
>
> On Sat, Jun 13, 2020 at 5:01 AM Álvaro Fernández Rojas
> <[email protected]> wrote:
>>
>> Hi Kamal,
>>
>>> El 12 jun 2020, a las 20:47, Kamal Dasu <[email protected]> escribió:
>>>
>>> On Fri, Jun 5, 2020 at 1:07 PM Álvaro Fernández Rojas <[email protected]> wrote:
>>>>
>>>> MTD_OPS_AUTO_OOB is writting OOB with ECC enabled, which changes all ECC bytes
>>>> from an erased page to 0x00 when JFFS2 cleanmarkers are added with mtd-utils.
>>>> | BBI | JFFS2 | ECC | JFFS2 | Spare |
>>>> 00000800 ff ff 19 85 20 03 00 00 00 00 00 00 08 ff ff ff
>>>>
>>>> However, if OOB is written with ECC disabled, the JFFS2 cleanmarkers are
>>>> correctly written without changing the ECC bytes:
>>>> | BBI | JFFS2 | ECC | JFFS2 | Spare |
>>>> 00000800 ff ff 19 85 20 03 ff ff ff 00 00 00 08 ff ff ff
>>>
>>> Both brcmand_write_oob_raw() and brcmnand_write_oob() use
>>> brcmnand_write() that uses PROGRAM_PAGE cmd, means also programs data
>>> areas and ECC when enabled is always calculated on DATA+OOB. since
>>
>> Are you sure about that? I think that HW ECC is only calculated for DATA, not for OOB.
>> The fact that we’re not writing any DATA seems to be the problem that is changing all ECC bytes to 0x00.
>>
>
> Only true for 1-bit hamming code on early controller versions. For
> BCH algorithms both data+oob are covered. And the controller driver
> intentionally does not implement a spare area program cmd, even for
> OOB writes. Also BRCMNAND_ACC_CONTROL_PARTIAL_PAGE=0 (when present)
> does not allow for spare areas only writes.
>
>>> in both cases we only want to modify OOB, data is always assumed to be
>>> 0xffs (means erased state). So as far as this api always is used on
>>> the erased page it should be good. Are the sub-pages/oob areas read by
>>> jffs2 also read without ecc enabled?. Just want to be sure that it
>>> does not break any other utilities like nandwrite.
>>
>> No, sub-pages/oob areas read by JFFS2 with ECC enabled.
>> I don’t think this breaks anything at all, since I tested nandwrite with OOB enabled and everything was written perfectly.
>>
>
> Going by the commit message you are assuming 1-bit hamming code, that
> is the only exception on early version controllers where only data was
> covered for ecc calculations when enabled.
> Which version of the controller are you using ?. Did you test with
> BCH-4 or any BCH ?.

All my devices use hamming ECC, even the ones with controller version v4.0 (BCM63268), which should also support BCH.
Therefore I need to stick with hamming ECC if I want the bootloader to be able to boot the kernel.

However, I should get a new device with BCH in a few days.
I’ll do more tests once I get it, but if BCH also covers OOB, then we could conditionally force write_oob to RAW only if hamming is configured.

>
>> BTW, I tried another approach that forced MTD_OPS_AUTO_OOB to be written as raw OOB, but it was rejected:
>> http://patchwork.ozlabs.org/project/linux-mtd/patch/[email protected]/
>> https://lkml.org/lkml/2020/5/4/215
>>
>
> Are there any other use cases other than jffs2 where only oob needs to
> be modified ?. But surely intentionally disabling ecc instead of
> forcing it is the way, but I am not sure it will still work for other
> BCH algorithms though where both data and oob are covered.

I’ll test this and report back once I get my new device.

>
>>>
>>>>
>>>> Signed-off-by: Álvaro Fernández Rojas <[email protected]>
>>>> ---
>>>> drivers/mtd/nand/raw/brcmnand/brcmnand.c | 9 +--------
>>>> 1 file changed, 1 insertion(+), 8 deletions(-)
>>>>
>>>> diff --git a/drivers/mtd/nand/raw/brcmnand/brcmnand.c b/drivers/mtd/nand/raw/brcmnand/brcmnand.c
>>>> index 8f9ffb46a09f..566281770841 100644
>>>> --- a/drivers/mtd/nand/raw/brcmnand/brcmnand.c
>>>> +++ b/drivers/mtd/nand/raw/brcmnand/brcmnand.c
>>>> @@ -2279,13 +2279,6 @@ static int brcmnand_write_page_raw(struct nand_chip *chip, const uint8_t *buf,
>>>> return nand_prog_page_end_op(chip);
>>>> }
>>>>
>>>> -static int brcmnand_write_oob(struct nand_chip *chip, int page)
>>>> -{
>>>> - return brcmnand_write(nand_to_mtd(chip), chip,
>>>> - (u64)page << chip->page_shift, NULL,
>>>> - chip->oob_poi);
>>>> -}
>>>> -
>>>> static int brcmnand_write_oob_raw(struct nand_chip *chip, int page)
>>>> {
>>>> struct mtd_info *mtd = nand_to_mtd(chip);
>>>> @@ -2642,7 +2635,7 @@ static int brcmnand_init_cs(struct brcmnand_host *host, struct device_node *dn)
>>>> chip->ecc.write_oob_raw = brcmnand_write_oob_raw;
>>>> chip->ecc.read_oob_raw = brcmnand_read_oob_raw;
>>>> chip->ecc.read_oob = brcmnand_read_oob;
>>>> - chip->ecc.write_oob = brcmnand_write_oob;
>>>> + chip->ecc.write_oob = brcmnand_write_oob_raw;
>>>>
>>>> chip->controller = &ctrl->controller;
>>>>
>>>> --
>>>> 2.26.2
>>>>
>>
>> Best regards,
>> Álvaro.