Since mac0/1 and mac2/3 are physically located on different die,
they have different properties by nature, which is mac0/1 has smaller delay step.
The property 'phy-mode' on ast2600 mac0 and mac1 is recommended to set to 'rgmii-rxid'
which enables the RX interface delay from the PHY chip.
Refer page 45 of SDK User Guide v08.00
https://github.com/AspeedTech-BMC/openbmc/releases/download/v08.00/SDK_User_Guide_v08.00.pdf
Set mac delay according to the mactest result.
Signed-off-by: Howard Chiu <[email protected]>
---
arch/arm/boot/dts/aspeed-ast2600-evb.dts | 19 +++++++++++++++++--
1 file changed, 17 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/aspeed-ast2600-evb.dts b/arch/arm/boot/dts/aspeed-ast2600-evb.dts
index b7eb552640cb..db16ba307e97 100644
--- a/arch/arm/boot/dts/aspeed-ast2600-evb.dts
+++ b/arch/arm/boot/dts/aspeed-ast2600-evb.dts
@@ -103,7 +103,7 @@ ethphy3: ethernet-phy@0 {
&mac0 {
status = "okay";
- phy-mode = "rgmii";
+ phy-mode = "rgmii-rxid";
phy-handle = <ðphy0>;
pinctrl-names = "default";
@@ -114,7 +114,7 @@ &mac0 {
&mac1 {
status = "okay";
- phy-mode = "rgmii";
+ phy-mode = "rgmii-rxid";
phy-handle = <ðphy1>;
pinctrl-names = "default";
@@ -141,6 +141,21 @@ &mac3 {
pinctrl-0 = <&pinctrl_rgmii4_default>;
};
+&syscon {
+ mac0-clk-delay = <0x10 0x0a
+ 0x10 0x10
+ 0x10 0x10>;
+ mac1-clk-delay = <0x10 0x0a
+ 0x10 0x10
+ 0x10 0x10>;
+ mac2-clk-delay = <0x08 0x04
+ 0x08 0x04
+ 0x08 0x04>;
+ mac3-clk-delay = <0x08 0x04
+ 0x08 0x04
+ 0x08 0x04>;
+};
+
&emmc_controller {
status = "okay";
};
--
2.25.1
Hi Howard,
On Fri, 18 Mar 2022 at 08:09, Howard Chiu <[email protected]> wrote:
>
> Since mac0/1 and mac2/3 are physically located on different die,
> they have different properties by nature, which is mac0/1 has smaller delay step.
>
> The property 'phy-mode' on ast2600 mac0 and mac1 is recommended to set to 'rgmii-rxid'
> which enables the RX interface delay from the PHY chip.
> Refer page 45 of SDK User Guide v08.00
> https://github.com/AspeedTech-BMC/openbmc/releases/download/v08.00/SDK_User_Guide_v08.00.pdf
>
> Set mac delay according to the mactest result.
This bit confused me. How does the rxid relate to the mac delay
numbers? Which device and code is responsible for using them?
>
> Signed-off-by: Howard Chiu <[email protected]>
> ---
> arch/arm/boot/dts/aspeed-ast2600-evb.dts | 19 +++++++++++++++++--
> 1 file changed, 17 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm/boot/dts/aspeed-ast2600-evb.dts b/arch/arm/boot/dts/aspeed-ast2600-evb.dts
> index b7eb552640cb..db16ba307e97 100644
> --- a/arch/arm/boot/dts/aspeed-ast2600-evb.dts
> +++ b/arch/arm/boot/dts/aspeed-ast2600-evb.dts
> @@ -103,7 +103,7 @@ ethphy3: ethernet-phy@0 {
> &mac0 {
> status = "okay";
>
> - phy-mode = "rgmii";
> + phy-mode = "rgmii-rxid";
> phy-handle = <ðphy0>;
>
> pinctrl-names = "default";
> @@ -114,7 +114,7 @@ &mac0 {
> &mac1 {
> status = "okay";
>
> - phy-mode = "rgmii";
> + phy-mode = "rgmii-rxid";
> phy-handle = <ðphy1>;
>
> pinctrl-names = "default";
> @@ -141,6 +141,21 @@ &mac3 {
> pinctrl-0 = <&pinctrl_rgmii4_default>;
> };
>
> +&syscon {
> + mac0-clk-delay = <0x10 0x0a
> + 0x10 0x10
> + 0x10 0x10>;
These properties aren't supported by the mainline kernel. Do you have
some code coming for that support?
> + mac1-clk-delay = <0x10 0x0a
> + 0x10 0x10
> + 0x10 0x10>;
> + mac2-clk-delay = <0x08 0x04
> + 0x08 0x04
> + 0x08 0x04>;
> + mac3-clk-delay = <0x08 0x04
> + 0x08 0x04
> + 0x08 0x04>;
> +};
> +
> &emmc_controller {
> status = "okay";
> };
> --
> 2.25.1
>
Hi Joel
> > +&syscon {
> > + mac0-clk-delay = <0x10 0x0a
> > + 0x10 0x10
> > + 0x10 0x10>;
>
> These properties aren't supported by the mainline kernel. Do you have some
> code coming for that support?
No, clk-ast2600 did not support it yet.
Let me remove this setting for now since I confirmed that the patch wouldn't be ready very soon.
Currently, the delay will be set at u-boot stage with commit for OpenBMC https://github.com/openbmc/u-boot/commit/e40a4e447a0e7f4d8b38c3256349e39ff3701f1f
So it should be safe for OpenBMC if this part was removed.
> -----Original Message-----
> From: Joel Stanley <[email protected]>
> Sent: Friday, March 18, 2022 4:46 PM
> To: Howard Chiu <[email protected]>
> Cc: [email protected]; [email protected]; [email protected];
> [email protected]; [email protected];
> [email protected]; Troy Lee <[email protected]>
> Subject: Re: [PATCH v1] ARM: dts: aspeed: ast2600-evb: Enable RX delay for
> MAC0/MAC1
>
> Hi Howard,
>
> On Fri, 18 Mar 2022 at 08:09, Howard Chiu <[email protected]>
> wrote:
> >
> > Since mac0/1 and mac2/3 are physically located on different die, they
> > have different properties by nature, which is mac0/1 has smaller delay step.
> >
> > The property 'phy-mode' on ast2600 mac0 and mac1 is recommended to set
> to 'rgmii-rxid'
> > which enables the RX interface delay from the PHY chip.
> > Refer page 45 of SDK User Guide v08.00
> >
> https://github.com/AspeedTech-BMC/openbmc/releases/download/v08.00/SD
> K
> > _User_Guide_v08.00.pdf
> >
> > Set mac delay according to the mactest result.
>
> This bit confused me. How does the rxid relate to the mac delay numbers?
> Which device and code is responsible for using them?
>
> >
> > Signed-off-by: Howard Chiu <[email protected]>
> > ---
> > arch/arm/boot/dts/aspeed-ast2600-evb.dts | 19 +++++++++++++++++--
> > 1 file changed, 17 insertions(+), 2 deletions(-)
> >
> > diff --git a/arch/arm/boot/dts/aspeed-ast2600-evb.dts
> > b/arch/arm/boot/dts/aspeed-ast2600-evb.dts
> > index b7eb552640cb..db16ba307e97 100644
> > --- a/arch/arm/boot/dts/aspeed-ast2600-evb.dts
> > +++ b/arch/arm/boot/dts/aspeed-ast2600-evb.dts
> > @@ -103,7 +103,7 @@ ethphy3: ethernet-phy@0 {
> > &mac0 {
> > status = "okay";
> >
> > - phy-mode = "rgmii";
> > + phy-mode = "rgmii-rxid";
> > phy-handle = <ðphy0>;
> >
> > pinctrl-names = "default";
> > @@ -114,7 +114,7 @@ &mac0 {
> > &mac1 {
> > status = "okay";
> >
> > - phy-mode = "rgmii";
> > + phy-mode = "rgmii-rxid";
> > phy-handle = <ðphy1>;
> >
> > pinctrl-names = "default";
> > @@ -141,6 +141,21 @@ &mac3 {
> > pinctrl-0 = <&pinctrl_rgmii4_default>; };
> >
> > +&syscon {
> > + mac0-clk-delay = <0x10 0x0a
> > + 0x10 0x10
> > + 0x10 0x10>;
>
> These properties aren't supported by the mainline kernel. Do you have some
> code coming for that support?
>
> > + mac1-clk-delay = <0x10 0x0a
> > + 0x10 0x10
> > + 0x10 0x10>;
> > + mac2-clk-delay = <0x08 0x04
> > + 0x08 0x04
> > + 0x08 0x04>;
> > + mac3-clk-delay = <0x08 0x04
> > + 0x08 0x04
> > + 0x08 0x04>;
> > +};
> > +
> > &emmc_controller {
> > status = "okay";
> > };
> > --
> > 2.25.1
> >