Most litex boards using RISC-V soft cores us the sbi earlycon, however
this is not available for non RISC-V litex SoC's. This patch enables
earlycon for liteuart which is available on all Litex SoC's making
support for earycon debugging more widely available.
Signed-off-by: Stafford Horne <[email protected]>
Cc: Florent Kermarrec <[email protected]>
Cc: Mateusz Holenko <[email protected]>
Cc: Joel Stanley <[email protected]>
Cc: Gabriel L. Somlo <[email protected]>
Reviewed-and-tested-by: Gabriel Somlo <[email protected]>
---
Changes since v1:
- Fixed subject
- Fixed ifdef and config issues pointed out by Jiri
- Use liteuart_putchar instead of early_liteuart_putc
.../admin-guide/kernel-parameters.txt | 5 +++++
drivers/tty/serial/Kconfig | 1 +
drivers/tty/serial/liteuart.c | 21 +++++++++++++++++++
3 files changed, 27 insertions(+)
diff --git a/Documentation/admin-guide/kernel-parameters.txt b/Documentation/admin-guide/kernel-parameters.txt
index 04545725f187..2d4a43af8de2 100644
--- a/Documentation/admin-guide/kernel-parameters.txt
+++ b/Documentation/admin-guide/kernel-parameters.txt
@@ -1084,6 +1084,11 @@
the driver will use only 32-bit accessors to read/write
the device registers.
+ liteuart,<addr>
+ Start an early console on a litex serial port at the
+ specified address. The serial port must already be
+ setup and configured. Options are not yet supported.
+
meson,<addr>
Start an early, polled-mode console on a meson serial
port at the specified address. The serial port must
diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
index 0c4cd4a348f4..af41e534483c 100644
--- a/drivers/tty/serial/Kconfig
+++ b/drivers/tty/serial/Kconfig
@@ -1550,6 +1550,7 @@ config SERIAL_LITEUART_CONSOLE
bool "LiteUART serial port console support"
depends on SERIAL_LITEUART=y
select SERIAL_CORE_CONSOLE
+ select SERIAL_EARLYCON
help
Say 'Y' or 'M' here if you wish to use the FPGA-based LiteUART serial
controller from LiteX SoC builder as the system console
diff --git a/drivers/tty/serial/liteuart.c b/drivers/tty/serial/liteuart.c
index 64842f3539e1..1b75a4bf7c56 100644
--- a/drivers/tty/serial/liteuart.c
+++ b/drivers/tty/serial/liteuart.c
@@ -370,6 +370,27 @@ static int __init liteuart_console_init(void)
return 0;
}
console_initcall(liteuart_console_init);
+
+static void early_liteuart_write(struct console *console, const char *s,
+ unsigned int count)
+{
+ struct earlycon_device *device = console->data;
+ struct uart_port *port = &device->port;
+
+ uart_console_write(port, s, count, liteuart_putchar);
+}
+
+static int __init early_liteuart_setup(struct earlycon_device *device,
+ const char *options)
+{
+ if (!device->port.membase)
+ return -ENODEV;
+
+ device->con->write = early_liteuart_write;
+ return 0;
+}
+
+OF_EARLYCON_DECLARE(liteuart, "litex,liteuart", early_liteuart_setup);
#endif /* CONFIG_SERIAL_LITEUART_CONSOLE */
static int __init liteuart_init(void)
--
2.31.1
On 17. 05. 21, 13:54, Stafford Horne wrote:
> Most litex boards using RISC-V soft cores us the sbi earlycon, however
> this is not available for non RISC-V litex SoC's. This patch enables
> earlycon for liteuart which is available on all Litex SoC's making
> support for earycon debugging more widely available.
>
> Signed-off-by: Stafford Horne <[email protected]>
> Cc: Florent Kermarrec <[email protected]>
> Cc: Mateusz Holenko <[email protected]>
> Cc: Joel Stanley <[email protected]>
> Cc: Gabriel L. Somlo <[email protected]>
> Reviewed-and-tested-by: Gabriel Somlo <[email protected]>
Reviewed-by: Jiri Slaby <[email protected]>
> ---
> Changes since v1:
> - Fixed subject
> - Fixed ifdef and config issues pointed out by Jiri
> - Use liteuart_putchar instead of early_liteuart_putc
>
> .../admin-guide/kernel-parameters.txt | 5 +++++
> drivers/tty/serial/Kconfig | 1 +
> drivers/tty/serial/liteuart.c | 21 +++++++++++++++++++
> 3 files changed, 27 insertions(+)
>
> diff --git a/Documentation/admin-guide/kernel-parameters.txt b/Documentation/admin-guide/kernel-parameters.txt
> index 04545725f187..2d4a43af8de2 100644
> --- a/Documentation/admin-guide/kernel-parameters.txt
> +++ b/Documentation/admin-guide/kernel-parameters.txt
> @@ -1084,6 +1084,11 @@
> the driver will use only 32-bit accessors to read/write
> the device registers.
>
> + liteuart,<addr>
> + Start an early console on a litex serial port at the
> + specified address. The serial port must already be
> + setup and configured. Options are not yet supported.
> +
> meson,<addr>
> Start an early, polled-mode console on a meson serial
> port at the specified address. The serial port must
> diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
> index 0c4cd4a348f4..af41e534483c 100644
> --- a/drivers/tty/serial/Kconfig
> +++ b/drivers/tty/serial/Kconfig
> @@ -1550,6 +1550,7 @@ config SERIAL_LITEUART_CONSOLE
> bool "LiteUART serial port console support"
> depends on SERIAL_LITEUART=y
> select SERIAL_CORE_CONSOLE
> + select SERIAL_EARLYCON
> help
> Say 'Y' or 'M' here if you wish to use the FPGA-based LiteUART serial
> controller from LiteX SoC builder as the system console
> diff --git a/drivers/tty/serial/liteuart.c b/drivers/tty/serial/liteuart.c
> index 64842f3539e1..1b75a4bf7c56 100644
> --- a/drivers/tty/serial/liteuart.c
> +++ b/drivers/tty/serial/liteuart.c
> @@ -370,6 +370,27 @@ static int __init liteuart_console_init(void)
> return 0;
> }
> console_initcall(liteuart_console_init);
> +
> +static void early_liteuart_write(struct console *console, const char *s,
> + unsigned int count)
> +{
> + struct earlycon_device *device = console->data;
> + struct uart_port *port = &device->port;
> +
> + uart_console_write(port, s, count, liteuart_putchar);
> +}
> +
> +static int __init early_liteuart_setup(struct earlycon_device *device,
> + const char *options)
> +{
> + if (!device->port.membase)
> + return -ENODEV;
> +
> + device->con->write = early_liteuart_write;
> + return 0;
> +}
> +
> +OF_EARLYCON_DECLARE(liteuart, "litex,liteuart", early_liteuart_setup);
> #endif /* CONFIG_SERIAL_LITEUART_CONSOLE */
>
> static int __init liteuart_init(void)
>
thanks,
--
js
suse labs
On Mon, 17 May 2021 at 11:55, Stafford Horne <[email protected]> wrote:
>
> Most litex boards using RISC-V soft cores us the sbi earlycon, however
> this is not available for non RISC-V litex SoC's. This patch enables
> earlycon for liteuart which is available on all Litex SoC's making
> support for earycon debugging more widely available.
>
> Signed-off-by: Stafford Horne <[email protected]>
> Cc: Florent Kermarrec <[email protected]>
> Cc: Mateusz Holenko <[email protected]>
> Cc: Joel Stanley <[email protected]>
> Cc: Gabriel L. Somlo <[email protected]>
> Reviewed-and-tested-by: Gabriel Somlo <[email protected]>
Reviewed-by: Joel Stanley <[email protected]>
Cheers,
Joel
On Tue, May 18, 2021 at 12:02:57PM +0000, Joel Stanley wrote:
> On Mon, 17 May 2021 at 11:55, Stafford Horne <[email protected]> wrote:
> >
> > Most litex boards using RISC-V soft cores us the sbi earlycon, however
> > this is not available for non RISC-V litex SoC's. This patch enables
> > earlycon for liteuart which is available on all Litex SoC's making
> > support for earycon debugging more widely available.
> >
> > Signed-off-by: Stafford Horne <[email protected]>
> > Cc: Florent Kermarrec <[email protected]>
> > Cc: Mateusz Holenko <[email protected]>
> > Cc: Joel Stanley <[email protected]>
> > Cc: Gabriel L. Somlo <[email protected]>
> > Reviewed-and-tested-by: Gabriel Somlo <[email protected]>
>
> Reviewed-by: Joel Stanley <[email protected]>
Thanks for reviewing.
-Stafford