Quoting Srinivasa Rao Mandadapu (2022-03-21 05:28:14)
> diff --git a/arch/arm64/boot/dts/qcom/sc7280-crd.dts b/arch/arm64/boot/dts/qcom/sc7280-crd.dts
> index e2efbdd..224a82d 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280-crd.dts
> +++ b/arch/arm64/boot/dts/qcom/sc7280-crd.dts
> @@ -84,6 +84,12 @@ ap_ts_pen_1v8: &i2c13 {
> pins = "gpio51";
> };
>
> +&wcd938x {
> + pinctrl-names = "default";
> + pinctrl-0 = <&us_euro_select>;
> + us-euro-gpios = <&tlmm 81 GPIO_ACTIVE_HIGH>;
> +};
> +
> &tlmm {
> tp_int_odl: tp-int-odl {
> pins = "gpio7";
> diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
> index de646d9..c6a04c3 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
> @@ -20,6 +20,14 @@
> #include "sc7280-chrome-common.dtsi"
>
> / {
> + max98360a: audio-codec-0 {
> + compatible = "maxim,max98360a";
> + pinctrl-names = "default";
> + pinctrl-0 = <&_en>;
> + sdmode-gpios = <&tlmm 63 GPIO_ACTIVE_HIGH>;
> + #sound-dai-cells = <0>;
> + };
> +
> chosen {
> stdout-path = "serial0:115200n8";
> };
> diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
> index 4a7b18a..5f75c9a 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
> @@ -20,6 +20,41 @@
> serial1 = &uart7;
> };
>
> + max98360a: audio-codec-0 {
> + compatible = "maxim,max98360a";
> + pinctrl-names = "default";
> + pinctrl-0 = <&_en>;
> + sdmode-gpios = <&tlmm 63 GPIO_ACTIVE_HIGH>;
> + #sound-dai-cells = <0>;
> + };
> +
> + wcd938x: audio-codec-1 {
> + compatible = "qcom,wcd9380-codec";
> + #sound-dai-cells = <1>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&wcd938x_reset_active>, <&wcd938x_reset_sleep>;
> + reset-gpios = <&tlmm 83 GPIO_ACTIVE_HIGH>;
> +
> + qcom,rx-device = <&wcd_rx>;
> + qcom,tx-device = <&wcd_tx>;
> +
> + vdd-rxtx-supply = <&vreg_l18b_1p8>;
> + vdd-io-supply = <&vreg_l18b_1p8>;
> + vdd-buck-supply = <&vreg_l17b_1p8>;
> + vdd-mic-bias-supply = <&vreg_bob>;
> +
> + qcom,micbias1-microvolt = <1800000>;
> + qcom,micbias2-microvolt = <1800000>;
> + qcom,micbias3-microvolt = <1800000>;
> + qcom,micbias4-microvolt = <1800000>;
> +
> + qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000
> + 500000 500000 500000>;
> + qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
> + qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
> + };
> +
> gpio-keys {
> compatible = "gpio-keys";
> label = "gpio-keys";
> @@ -476,6 +511,143 @@
> drive-strength = <6>;
> };
>
> +&soc {
Why is the soc node being modified in the board file? I expect these
nodes to always be present in the SoC (sc7280) so they should be largely
defined in the sc7280.dtsi file, except for any voltage supplies that
are described in the board file because the board design dictates what
power supplies are connected to the SoC pads.
> + rxmacro: codec@3200000 {
> + compatible = "qcom,sc7280-lpass-rx-macro";
> + reg = <0 0x03200000 0 0x1000>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&rx_swr_active>;
> +
> + clocks = <&lpass_aon LPASS_AON_CC_TX_MCLK_CLK>,
> + <&lpass_aon LPASS_AON_CC_TX_MCLK_2X_CLK>,
> + <&vamacro>;
> + clock-names = "mclk", "npl", "fsgen";
> +
> + power-domains = <&lpass_hm LPASS_CORE_CC_LPASS_CORE_HM_GDSC>,
> + <&lpass_aon LPASS_AON_CC_LPASS_AUDIO_HM_GDSC>;
> + power-domain-names ="macro", "dcodec";
> +
> + #clock-cells = <0>;
> + #sound-dai-cells = <1>;
> + };
This whole node can be moved to sc7280.dtsi and then we can have a
simple
&rxmacro {
status = "okay";
};
here.
> +
> + txmacro: codec@3220000 {
> + compatible = "qcom,sc7280-lpass-tx-macro";
> + reg = <0 0x03220000 0 0x1000>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&tx_swr_active>;
> +
> + clocks = <&lpass_aon LPASS_AON_CC_TX_MCLK_CLK>,
> + <&lpass_aon LPASS_AON_CC_TX_MCLK_2X_CLK>,
> + <&vamacro>;
> + clock-names = "mclk", "npl", "fsgen";
> +
> + power-domains = <&lpass_hm LPASS_CORE_CC_LPASS_CORE_HM_GDSC>,
> + <&lpass_aon LPASS_AON_CC_LPASS_AUDIO_HM_GDSC>;
> + power-domain-names ="macro", "dcodec";
> +
> + #clock-cells = <0>;
> + #sound-dai-cells = <1>;
Same, but txmacro.
> + };
> +
> + vamacro: codec@3370000 {
> + compatible = "qcom,sc7280-lpass-va-macro";
> + reg = <0 0x03370000 0 0x1000>;
> +
> + pinctrl-0 = <&dmic01_active>;
> + pinctrl-names = "default";
> +
> + clocks = <&lpass_aon LPASS_AON_CC_TX_MCLK_CLK>;
> + clock-names = "mclk";
> +
> + power-domains = <&lpass_hm LPASS_CORE_CC_LPASS_CORE_HM_GDSC>,
> + <&lpass_aon LPASS_AON_CC_LPASS_AUDIO_HM_GDSC>;
> + power-domain-names ="macro", "dcodec";
> +
> + vdd-micb-supply = <&vreg_bob>;
> +
> + #clock-cells = <0>;
> + #sound-dai-cells = <1>;
This one can move as well, except for vdd-micb-supply which needs to
stay here.
&vamacro {
status = "okay";
vdd-micb-supply = <&vreg_bob>;
};
> + };
> +
> + swr0: soundwire@3210000 {
> + compatible = "qcom,soundwire-v1.6.0";
> + reg = <0 0x03210000 0 0x2000>;
This node should largely go into the sc7280.dtsi file.
> +
> + interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&rxmacro>;
> + clock-names = "iface";
> +
> + qcom,din-ports = <0>;
> + qcom,dout-ports = <5>;
> +
> + resets = <&lpass_audiocc LPASS_AUDIO_SWR_RX_CGCR>;
> + reset-names = "swr_audio_cgcr";
> +
> + qcom,ports-word-length = /bits/ 8 <0x01 0x07 0x04 0xff 0xff>;
> + qcom,ports-sinterval-low = /bits/ 8 <0x03 0x3f 0x1f 0x03 0x03>;
> + qcom,ports-offset1 = /bits/ 8 <0x00 0x00 0x0b 0x01 0x01>;
> + qcom,ports-offset2 = /bits/ 8 <0x00 0x00 0x0b 0x00 0x00>;
> + qcom,ports-lane-control = /bits/ 8 <0x01 0x00 0x00 0x00 0x00>;
> + qcom,ports-block-pack-mode = /bits/ 8 <0xff 0x00 0x01 0xff 0xff>;
> + qcom,ports-hstart = /bits/ 8 <0xff 0x03 0xff 0xff 0xff>;
> + qcom,ports-hstop = /bits/ 8 <0xff 0x06 0xff 0xff 0xff>;
> + qcom,ports-block-group-count = /bits/ 8 <0xff 0xff 0xff 0xff 0x00>;
Are these properties board specific? The sm8250.dtsi file has them so I
guess not.
> +
> + #sound-dai-cells = <1>;
> + #address-cells = <2>;
> + #size-cells = <0>;
> +
> + wcd_rx: codec@0,4 {
> + compatible = "sdw20217010d00";
Is this some component on the board? If so then it should stay here in
this file.
> + reg = <0 4>;
> + #sound-dai-cells = <1>;
> + qcom,rx-port-mapping = <1 2 3 4 5>;
> + };
> + };
> +
> + swr1: soundwire@3230000 {
> + compatible = "qcom,soundwire-v1.6.0";
> + reg = <0 0x03230000 0 0x2000>;
> +
> + interrupts-extended = <&intc GIC_SPI 496 IRQ_TYPE_LEVEL_HIGH>,
> + <&pdc 130 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "swr_master_irq", "swr_wake_irq";
> + clocks = <&txmacro>;
> + clock-names = "iface";
> +
> + qcom,din-ports = <3>;
> + qcom,dout-ports = <0>;
> +
> + resets = <&lpass_audiocc LPASS_AUDIO_SWR_TX_CGCR>;
> + reset-names = "swr_audio_cgcr";
> +
> + qcom,ports-sinterval-low = /bits/ 8 <0x01 0x03 0x03>;
> + qcom,ports-offset1 = /bits/ 8 <0x01 0x00 0x02>;
> + qcom,ports-offset2 = /bits/ 8 <0x00 0x00 0x00>;
> + qcom,ports-hstart = /bits/ 8 <0xff 0xff 0xff>;
> + qcom,ports-hstop = /bits/ 8 <0xff 0xff 0xff>;
> + qcom,ports-word-length = /bits/ 8 <0xff 0x0 0xff>;
> + qcom,ports-block-pack-mode = /bits/ 8 <0xff 0xff 0xff>;
> + qcom,ports-block-group-count = /bits/ 8 <0xff 0xff 0xff>;
> + qcom,ports-lane-control = /bits/ 8 <0x00 0x01 0x00>;
> + qcom,port-offset = <1>;
> +
> + #sound-dai-cells = <1>;
> + #address-cells = <2>;
> + #size-cells = <0>;
> +
> + wcd_tx: codec@0,3 {
> + compatible = "sdw20217010d00";
> + reg = <0 3>;
> + #sound-dai-cells = <1>;
> + qcom,tx-port-mapping = <1 2 3 4>;
> + };
Same question about being a board component. Probably yes?
> + };
> +};
> +
> &tlmm {
> amp_en: amp-en {
On 3/22/2022 1:35 AM, Stephen Boyd wrote:
Thanks for your time Stephen!!!
> Quoting Srinivasa Rao Mandadapu (2022-03-21 05:28:14)
>> diff --git a/arch/arm64/boot/dts/qcom/sc7280-crd.dts b/arch/arm64/boot/dts/qcom/sc7280-crd.dts
>> index e2efbdd..224a82d 100644
>> --- a/arch/arm64/boot/dts/qcom/sc7280-crd.dts
>> +++ b/arch/arm64/boot/dts/qcom/sc7280-crd.dts
>> @@ -84,6 +84,12 @@ ap_ts_pen_1v8: &i2c13 {
>> pins = "gpio51";
>> };
>>
>> +&wcd938x {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&us_euro_select>;
>> + us-euro-gpios = <&tlmm 81 GPIO_ACTIVE_HIGH>;
>> +};
>> +
>> &tlmm {
>> tp_int_odl: tp-int-odl {
>> pins = "gpio7";
>> diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
>> index de646d9..c6a04c3 100644
>> --- a/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
>> @@ -20,6 +20,14 @@
>> #include "sc7280-chrome-common.dtsi"
>>
>> / {
>> + max98360a: audio-codec-0 {
>> + compatible = "maxim,max98360a";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&_en>;
>> + sdmode-gpios = <&tlmm 63 GPIO_ACTIVE_HIGH>;
>> + #sound-dai-cells = <0>;
>> + };
>> +
>> chosen {
>> stdout-path = "serial0:115200n8";
>> };
>> diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
>> index 4a7b18a..5f75c9a 100644
>> --- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
>> @@ -20,6 +20,41 @@
>> serial1 = &uart7;
>> };
>>
>> + max98360a: audio-codec-0 {
>> + compatible = "maxim,max98360a";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&_en>;
>> + sdmode-gpios = <&tlmm 63 GPIO_ACTIVE_HIGH>;
>> + #sound-dai-cells = <0>;
>> + };
>> +
>> + wcd938x: audio-codec-1 {
>> + compatible = "qcom,wcd9380-codec";
>> + #sound-dai-cells = <1>;
>> +
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&wcd938x_reset_active>, <&wcd938x_reset_sleep>;
>> + reset-gpios = <&tlmm 83 GPIO_ACTIVE_HIGH>;
>> +
>> + qcom,rx-device = <&wcd_rx>;
>> + qcom,tx-device = <&wcd_tx>;
>> +
>> + vdd-rxtx-supply = <&vreg_l18b_1p8>;
>> + vdd-io-supply = <&vreg_l18b_1p8>;
>> + vdd-buck-supply = <&vreg_l17b_1p8>;
>> + vdd-mic-bias-supply = <&vreg_bob>;
>> +
>> + qcom,micbias1-microvolt = <1800000>;
>> + qcom,micbias2-microvolt = <1800000>;
>> + qcom,micbias3-microvolt = <1800000>;
>> + qcom,micbias4-microvolt = <1800000>;
>> +
>> + qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000
>> + 500000 500000 500000>;
>> + qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
>> + qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
>> + };
>> +
>> gpio-keys {
>> compatible = "gpio-keys";
>> label = "gpio-keys";
>> @@ -476,6 +511,143 @@
>> drive-strength = <6>;
>> };
>>
>> +&soc {
> Why is the soc node being modified in the board file? I expect these
> nodes to always be present in the SoC (sc7280) so they should be largely
> defined in the sc7280.dtsi file, except for any voltage supplies that
> are described in the board file because the board design dictates what
> power supplies are connected to the SoC pads.
Okay. will place accordingly.
>
>> + rxmacro: codec@3200000 {
>> + compatible = "qcom,sc7280-lpass-rx-macro";
>> + reg = <0 0x03200000 0 0x1000>;
>> +
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&rx_swr_active>;
>> +
>> + clocks = <&lpass_aon LPASS_AON_CC_TX_MCLK_CLK>,
>> + <&lpass_aon LPASS_AON_CC_TX_MCLK_2X_CLK>,
>> + <&vamacro>;
>> + clock-names = "mclk", "npl", "fsgen";
>> +
>> + power-domains = <&lpass_hm LPASS_CORE_CC_LPASS_CORE_HM_GDSC>,
>> + <&lpass_aon LPASS_AON_CC_LPASS_AUDIO_HM_GDSC>;
>> + power-domain-names ="macro", "dcodec";
>> +
>> + #clock-cells = <0>;
>> + #sound-dai-cells = <1>;
>> + };
> This whole node can be moved to sc7280.dtsi and then we can have a
> simple
>
> &rxmacro {
> status = "okay";
> };
>
> here.
Okay.
>
>> +
>> + txmacro: codec@3220000 {
>> + compatible = "qcom,sc7280-lpass-tx-macro";
>> + reg = <0 0x03220000 0 0x1000>;
>> +
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&tx_swr_active>;
>> +
>> + clocks = <&lpass_aon LPASS_AON_CC_TX_MCLK_CLK>,
>> + <&lpass_aon LPASS_AON_CC_TX_MCLK_2X_CLK>,
>> + <&vamacro>;
>> + clock-names = "mclk", "npl", "fsgen";
>> +
>> + power-domains = <&lpass_hm LPASS_CORE_CC_LPASS_CORE_HM_GDSC>,
>> + <&lpass_aon LPASS_AON_CC_LPASS_AUDIO_HM_GDSC>;
>> + power-domain-names ="macro", "dcodec";
>> +
>> + #clock-cells = <0>;
>> + #sound-dai-cells = <1>;
> Same, but txmacro.
Okay.
>
>> + };
>> +
>> + vamacro: codec@3370000 {
>> + compatible = "qcom,sc7280-lpass-va-macro";
>> + reg = <0 0x03370000 0 0x1000>;
>> +
>> + pinctrl-0 = <&dmic01_active>;
>> + pinctrl-names = "default";
>> +
>> + clocks = <&lpass_aon LPASS_AON_CC_TX_MCLK_CLK>;
>> + clock-names = "mclk";
>> +
>> + power-domains = <&lpass_hm LPASS_CORE_CC_LPASS_CORE_HM_GDSC>,
>> + <&lpass_aon LPASS_AON_CC_LPASS_AUDIO_HM_GDSC>;
>> + power-domain-names ="macro", "dcodec";
>> +
>> + vdd-micb-supply = <&vreg_bob>;
>> +
>> + #clock-cells = <0>;
>> + #sound-dai-cells = <1>;
> This one can move as well, except for vdd-micb-supply which needs to
> stay here.
>
> &vamacro {
> status = "okay";
> vdd-micb-supply = <&vreg_bob>;
> };
Okay.
>> + };
>> +
>> + swr0: soundwire@3210000 {
>> + compatible = "qcom,soundwire-v1.6.0";
>> + reg = <0 0x03210000 0 0x2000>;
> This node should largely go into the sc7280.dtsi file.
Okay.
>
>> +
>> + interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&rxmacro>;
>> + clock-names = "iface";
>> +
>> + qcom,din-ports = <0>;
>> + qcom,dout-ports = <5>;
>> +
>> + resets = <&lpass_audiocc LPASS_AUDIO_SWR_RX_CGCR>;
>> + reset-names = "swr_audio_cgcr";
>> +
>> + qcom,ports-word-length = /bits/ 8 <0x01 0x07 0x04 0xff 0xff>;
>> + qcom,ports-sinterval-low = /bits/ 8 <0x03 0x3f 0x1f 0x03 0x03>;
>> + qcom,ports-offset1 = /bits/ 8 <0x00 0x00 0x0b 0x01 0x01>;
>> + qcom,ports-offset2 = /bits/ 8 <0x00 0x00 0x0b 0x00 0x00>;
>> + qcom,ports-lane-control = /bits/ 8 <0x01 0x00 0x00 0x00 0x00>;
>> + qcom,ports-block-pack-mode = /bits/ 8 <0xff 0x00 0x01 0xff 0xff>;
>> + qcom,ports-hstart = /bits/ 8 <0xff 0x03 0xff 0xff 0xff>;
>> + qcom,ports-hstop = /bits/ 8 <0xff 0x06 0xff 0xff 0xff>;
>> + qcom,ports-block-group-count = /bits/ 8 <0xff 0xff 0xff 0xff 0x00>;
> Are these properties board specific? The sm8250.dtsi file has them so I
> guess not.
Yes. They are not board specific. will move accordingly.
>
>> +
>> + #sound-dai-cells = <1>;
>> + #address-cells = <2>;
>> + #size-cells = <0>;
>> +
>> + wcd_rx: codec@0,4 {
>> + compatible = "sdw20217010d00";
> Is this some component on the board? If so then it should stay here in
> this file.
Yes. it's WCD codec component on board.
>
>> + reg = <0 4>;
>> + #sound-dai-cells = <1>;
>> + qcom,rx-port-mapping = <1 2 3 4 5>;
>> + };
>> + };
>> +
>> + swr1: soundwire@3230000 {
>> + compatible = "qcom,soundwire-v1.6.0";
>> + reg = <0 0x03230000 0 0x2000>;
>> +
>> + interrupts-extended = <&intc GIC_SPI 496 IRQ_TYPE_LEVEL_HIGH>,
>> + <&pdc 130 IRQ_TYPE_LEVEL_HIGH>;
>> + interrupt-names = "swr_master_irq", "swr_wake_irq";
>> + clocks = <&txmacro>;
>> + clock-names = "iface";
>> +
>> + qcom,din-ports = <3>;
>> + qcom,dout-ports = <0>;
>> +
>> + resets = <&lpass_audiocc LPASS_AUDIO_SWR_TX_CGCR>;
>> + reset-names = "swr_audio_cgcr";
>> +
>> + qcom,ports-sinterval-low = /bits/ 8 <0x01 0x03 0x03>;
>> + qcom,ports-offset1 = /bits/ 8 <0x01 0x00 0x02>;
>> + qcom,ports-offset2 = /bits/ 8 <0x00 0x00 0x00>;
>> + qcom,ports-hstart = /bits/ 8 <0xff 0xff 0xff>;
>> + qcom,ports-hstop = /bits/ 8 <0xff 0xff 0xff>;
>> + qcom,ports-word-length = /bits/ 8 <0xff 0x0 0xff>;
>> + qcom,ports-block-pack-mode = /bits/ 8 <0xff 0xff 0xff>;
>> + qcom,ports-block-group-count = /bits/ 8 <0xff 0xff 0xff>;
>> + qcom,ports-lane-control = /bits/ 8 <0x00 0x01 0x00>;
>> + qcom,port-offset = <1>;
>> +
>> + #sound-dai-cells = <1>;
>> + #address-cells = <2>;
>> + #size-cells = <0>;
>> +
>> + wcd_tx: codec@0,3 {
>> + compatible = "sdw20217010d00";
>> + reg = <0 3>;
>> + #sound-dai-cells = <1>;
>> + qcom,tx-port-mapping = <1 2 3 4>;
>> + };
> Same question about being a board component. Probably yes?
Yes.
>
>> + };
>> +};
>> +
>> &tlmm {
>> amp_en: amp-en {