Add support for ROHM BH1710/BH1715/BH1721/BH1750/BH1751 ambient light
sensors.
Signed-off-by: Tomasz Duszynski <[email protected]>
---
drivers/iio/light/Kconfig | 10 ++
drivers/iio/light/Makefile | 1 +
drivers/iio/light/bh1750.c | 322 +++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 333 insertions(+)
create mode 100644 drivers/iio/light/bh1750.c
diff --git a/drivers/iio/light/Kconfig b/drivers/iio/light/Kconfig
index 5a3237b..9fb79ca 100644
--- a/drivers/iio/light/Kconfig
+++ b/drivers/iio/light/Kconfig
@@ -37,6 +37,16 @@ config APDS9300
To compile this driver as a module, choose M here: the
module will be called apds9300.
+config BH1750
+ tristate "BH1750 ambient light sensor"
+ depends on I2C
+ help
+ Say Y here to build support for the BH1710, BH1715, BH1721,
+ BH1750, BH1751 ambient light sensors.
+
+ To compile this driver as a module, choose M here: the module will
+ be called bh1750.
+
config CM32181
depends on I2C
tristate "CM32181 driver"
diff --git a/drivers/iio/light/Makefile b/drivers/iio/light/Makefile
index 74656c1..1a13184 100644
--- a/drivers/iio/light/Makefile
+++ b/drivers/iio/light/Makefile
@@ -6,6 +6,7 @@
obj-$(CONFIG_ADJD_S311) += adjd_s311.o
obj-$(CONFIG_AL3320A) += al3320a.o
obj-$(CONFIG_APDS9300) += apds9300.o
+obj-$(CONFIG_BH1750) += bh1750.o
obj-$(CONFIG_CM32181) += cm32181.o
obj-$(CONFIG_CM36651) += cm36651.o
obj-$(CONFIG_GP2AP020A00F) += gp2ap020a00f.o
diff --git a/drivers/iio/light/bh1750.c b/drivers/iio/light/bh1750.c
new file mode 100644
index 0000000..83b5413
--- /dev/null
+++ b/drivers/iio/light/bh1750.c
@@ -0,0 +1,322 @@
+/*
+ * ROHM BH1710/BH1715/BH1721/BH1750/BH1751 ambient light sensor driver
+ *
+ * Copyright (c) Tomasz Duszynski <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * Data sheets:
+ * http://rohmfs.rohm.com/en/products/databook/datasheet/ic/sensor/light/bh1710fvc-e.pdf
+ * http://rohmfs.rohm.com/en/products/databook/datasheet/ic/sensor/light/bh1715fvc-e.pdf
+ * http://rohmfs.rohm.com/en/products/databook/datasheet/ic/sensor/light/bh1721fvc-e.pdf
+ * http://rohmfs.rohm.com/en/products/databook/datasheet/ic/sensor/light/bh1750fvi-e.pdf
+ * http://rohmfs.rohm.com/en/products/databook/datasheet/ic/sensor/light/bh1751fvi-e.pdf
+ *
+ * 7-bit I2C slave addresses:
+ * 0x23 (ADDR pin low)
+ * 0x5C (ADDR pin high)
+ *
+ */
+
+#include <linux/delay.h>
+#include <linux/i2c.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/sysfs.h>
+#include <linux/module.h>
+
+#define BH1750_POWER_DOWN 0x00
+#define BH1750_H_RES_MODE 0x10 /* auto-mode for BH1721 */
+#define BH1750_CHANGE_INT_TIME_H_BIT 0x40
+#define BH1750_CHANGE_INT_TIME_L_BIT 0x60
+
+enum {
+ BH1710,
+ BH1715,
+ BH1721,
+ BH1750,
+ BH1751
+};
+
+struct bh1750_chip_info {
+ int id;
+ int mtreg_min;
+ int mtreg_max;
+ int mtreg_default;
+ int mtreg_to_usec;
+ int mtreg_to_scale;
+};
+
+struct bh1750_data {
+ struct i2c_client *client;
+ struct mutex lock;
+ const struct bh1750_chip_info *chip_info;
+ u16 mtreg;
+};
+
+static const struct bh1750_chip_info chip_info_tbl[] = {
+ [BH1710] = { BH1710, 140, 1022, 300, 400, 4000 },
+ [BH1715] = { BH1715, 31, 254, 69, 1740, 17391 },
+ [BH1721] = { BH1721, 140, 1020, 300, 400, 4000 },
+ [BH1750] = { BH1750, 31, 254, 69, 1740, 17391 },
+ [BH1751] = { BH1751, 31, 254, 69, 1740, 17391 }
+};
+
+static int bh1750_change_int_time(struct bh1750_data *data, int usec)
+{
+ int ret, val;
+ u8 low = 0, high = 0;
+ const struct bh1750_chip_info *chip_info = data->chip_info;
+
+ if ((usec % chip_info->mtreg_to_usec) != 0)
+ return -EINVAL;
+
+ val = usec / chip_info->mtreg_to_usec;
+ if (val < chip_info->mtreg_min || val > chip_info->mtreg_max)
+ return -EINVAL;
+
+ switch (chip_info->id) {
+ case BH1710:
+ low = val & 0x001F;
+ high = (val & 0x03E0) >> 5;
+ break;
+ case BH1721:
+ low = val & 0x0010;
+ high = (val & 0x03E0) >> 5;
+ case BH1715:
+ case BH1750:
+ case BH1751:
+ low = val & 0x001F;
+ high = (val & 0x00E0) >> 5;
+ break;
+ }
+
+ ret = i2c_smbus_write_byte(data->client, BH1750_POWER_DOWN);
+ if (ret < 0)
+ return ret;
+
+ ret = i2c_smbus_write_byte(data->client,
+ BH1750_CHANGE_INT_TIME_H_BIT | high);
+ if (ret < 0)
+ return ret;
+
+ ret = i2c_smbus_write_byte(data->client,
+ BH1750_CHANGE_INT_TIME_L_BIT | low);
+ if (ret < 0)
+ return ret;
+
+ data->mtreg = val;
+
+ return i2c_smbus_write_byte(data->client, BH1750_H_RES_MODE);
+}
+
+static int bh1750_read_raw(struct iio_dev *indio_dev,
+ struct iio_chan_spec const *chan,
+ int *val, int *val2, long mask)
+{
+ u16 result;
+ int ret, tmp;
+ unsigned long delay;
+ struct bh1750_data *data = iio_priv(indio_dev);
+ const struct bh1750_chip_info *chip_info = data->chip_info;
+
+ switch (mask) {
+ case IIO_CHAN_INFO_RAW:
+ switch (chan->type) {
+ case IIO_INTENSITY:
+ delay = chip_info->mtreg_to_usec * data->mtreg;
+ mutex_lock(&data->lock);
+ usleep_range(delay, delay + 20000);
+ ret = i2c_master_recv(data->client,
+ (char *)&result, 2);
+ mutex_unlock(&data->lock);
+ if (ret < 0)
+ return ret;
+
+ *val = swab16(result);
+ return IIO_VAL_INT;
+ default:
+ return -EINVAL;
+ }
+ case IIO_CHAN_INFO_SCALE:
+ tmp = chip_info->mtreg_to_scale * data->mtreg;
+ *val = tmp / 1000000;
+ *val2 = tmp % 1000000;
+ return IIO_VAL_INT_PLUS_MICRO;
+ case IIO_CHAN_INFO_INT_TIME:
+ *val = 0;
+ *val2 = chip_info->mtreg_to_usec * data->mtreg;
+ return IIO_VAL_INT_PLUS_MICRO;
+ default:
+ return -EINVAL;
+ }
+}
+
+static int bh1750_write_raw(struct iio_dev *indio_dev,
+ struct iio_chan_spec const *chan,
+ int val, int val2, long mask)
+{
+ int ret;
+ struct bh1750_data *data = iio_priv(indio_dev);
+
+ switch (mask) {
+ case IIO_CHAN_INFO_INT_TIME:
+ if (val != 0)
+ return -EINVAL;
+
+ mutex_lock(&data->lock);
+ ret = bh1750_change_int_time(data, val2);
+ mutex_unlock(&data->lock);
+ return ret;
+ default:
+ return -EINVAL;
+ }
+}
+
+static ssize_t bh1750_show_int_time_available(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ int i, inc;
+ size_t len = 0;
+ struct bh1750_data *data = iio_priv(dev_to_iio_dev(dev));
+ const struct bh1750_chip_info *chip_info = data->chip_info;
+
+ switch (chip_info->id) {
+ case BH1710:
+ case BH1721:
+ /* All values won't fit into one page, so display every
+ * second one. By doing so step size is increased
+ * from 0.4ms to 0.8ms.*/
+ inc = 2;
+ break;
+ default:
+ inc = 1;
+ break;
+ }
+
+ for (i = chip_info->mtreg_min; i <= chip_info->mtreg_max; i += inc)
+ len += scnprintf(buf + len, PAGE_SIZE - len, "0.%06d ",
+ i * chip_info->mtreg_to_usec);
+
+ buf[len - 1] = '\n';
+
+ return len;
+}
+
+static IIO_DEV_ATTR_INT_TIME_AVAIL(bh1750_show_int_time_available);
+
+static struct attribute *bh1750_attributes[] = {
+ &iio_dev_attr_integration_time_available.dev_attr.attr,
+ NULL,
+};
+
+static struct attribute_group bh1750_attribute_group = {
+ .attrs = bh1750_attributes,
+};
+
+static const struct iio_info bh1750_info = {
+ .driver_module = THIS_MODULE,
+ .attrs = &bh1750_attribute_group,
+ .read_raw = bh1750_read_raw,
+ .write_raw = bh1750_write_raw,
+};
+
+static const struct iio_chan_spec bh1750_channels[] = {
+ {
+ .type = IIO_INTENSITY,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
+ BIT(IIO_CHAN_INFO_SCALE) |
+ BIT(IIO_CHAN_INFO_INT_TIME)
+ }
+};
+
+static int bh1750_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ int ret, usec;
+ struct bh1750_data *data;
+ struct iio_dev *indio_dev;
+
+ if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C |
+ I2C_FUNC_SMBUS_WRITE_BYTE))
+ return -ENODEV;
+
+ indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data));
+ if (!indio_dev)
+ return -ENOMEM;
+
+ data = iio_priv(indio_dev);
+ i2c_set_clientdata(client, indio_dev);
+ data->client = client;
+ data->chip_info = &chip_info_tbl[id->driver_data];
+
+ usec = data->chip_info->mtreg_to_usec * data->chip_info->mtreg_default;
+ ret = bh1750_change_int_time(data, usec);
+ if (ret < 0)
+ return ret;
+
+ mutex_init(&data->lock);
+ indio_dev->dev.parent = &client->dev;
+ indio_dev->info = &bh1750_info;
+ indio_dev->name = id->name;
+ indio_dev->channels = bh1750_channels;
+ indio_dev->num_channels = ARRAY_SIZE(bh1750_channels);
+ indio_dev->modes = INDIO_DIRECT_MODE;
+
+ return devm_iio_device_register(&client->dev, indio_dev);
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int bh1750_suspend(struct device *dev)
+{
+ int ret;
+ struct bh1750_data *data =
+ iio_priv(i2c_get_clientdata(to_i2c_client(dev)));
+
+ mutex_lock(&data->lock);
+ ret = i2c_smbus_write_byte(data->client, BH1750_POWER_DOWN);
+ mutex_unlock(&data->lock);
+
+ return ret;
+}
+
+static int bh1750_resume(struct device *dev)
+{
+ struct bh1750_data *data =
+ iio_priv(i2c_get_clientdata(to_i2c_client(dev)));
+
+ return i2c_smbus_write_byte(data->client, BH1750_H_RES_MODE);
+}
+
+static SIMPLE_DEV_PM_OPS(bh1750_pm_ops, bh1750_suspend, bh1750_resume);
+#define BH1750_PM_OPS (&bh1750_pm_ops)
+#else
+#define BH1750_PM_OPS NULL
+#endif
+
+static const struct i2c_device_id bh1750_id[] = {
+ { "bh1710", BH1710 },
+ { "bh1715", BH1715 },
+ { "bh1721", BH1721 },
+ { "bh1750", BH1750 },
+ { "bh1751", BH1751 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, bh1750_id);
+
+static struct i2c_driver bh1750_driver = {
+ .driver = {
+ .name = "bh1750",
+ .owner = THIS_MODULE,
+ .pm = BH1750_PM_OPS,
+ },
+ .probe = bh1750_probe,
+ .id_table = bh1750_id,
+
+};
+module_i2c_driver(bh1750_driver);
+
+MODULE_AUTHOR("Tomasz Duszynski <[email protected]>");
+MODULE_DESCRIPTION("ROHM BH1710/BH1715/BH1721/BH1750/BH1751 als driver");
+MODULE_LICENSE("GPL v2");
--
2.3.5
On Tue, 21 Apr 2015, Tomasz Duszynski wrote:
> Add support for ROHM BH1710/BH1715/BH1721/BH1750/BH1751 ambient light
> sensors.
nice, some comments inline
> Signed-off-by: Tomasz Duszynski <[email protected]>
> ---
> drivers/iio/light/Kconfig | 10 ++
> drivers/iio/light/Makefile | 1 +
> drivers/iio/light/bh1750.c | 322 +++++++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 333 insertions(+)
> create mode 100644 drivers/iio/light/bh1750.c
>
> diff --git a/drivers/iio/light/Kconfig b/drivers/iio/light/Kconfig
> index 5a3237b..9fb79ca 100644
> --- a/drivers/iio/light/Kconfig
> +++ b/drivers/iio/light/Kconfig
> @@ -37,6 +37,16 @@ config APDS9300
> To compile this driver as a module, choose M here: the
> module will be called apds9300.
>
> +config BH1750
> + tristate "BH1750 ambient light sensor"
> + depends on I2C
> + help
> + Say Y here to build support for the BH1710, BH1715, BH1721,
> + BH1750, BH1751 ambient light sensors.
> +
> + To compile this driver as a module, choose M here: the module will
> + be called bh1750.
> +
> config CM32181
> depends on I2C
> tristate "CM32181 driver"
> diff --git a/drivers/iio/light/Makefile b/drivers/iio/light/Makefile
> index 74656c1..1a13184 100644
> --- a/drivers/iio/light/Makefile
> +++ b/drivers/iio/light/Makefile
> @@ -6,6 +6,7 @@
> obj-$(CONFIG_ADJD_S311) += adjd_s311.o
> obj-$(CONFIG_AL3320A) += al3320a.o
> obj-$(CONFIG_APDS9300) += apds9300.o
> +obj-$(CONFIG_BH1750) += bh1750.o
> obj-$(CONFIG_CM32181) += cm32181.o
> obj-$(CONFIG_CM36651) += cm36651.o
> obj-$(CONFIG_GP2AP020A00F) += gp2ap020a00f.o
> diff --git a/drivers/iio/light/bh1750.c b/drivers/iio/light/bh1750.c
> new file mode 100644
> index 0000000..83b5413
> --- /dev/null
> +++ b/drivers/iio/light/bh1750.c
> @@ -0,0 +1,322 @@
> +/*
> + * ROHM BH1710/BH1715/BH1721/BH1750/BH1751 ambient light sensor driver
> + *
> + * Copyright (c) Tomasz Duszynski <[email protected]>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + *
> + * Data sheets:
> + * http://rohmfs.rohm.com/en/products/databook/datasheet/ic/sensor/light/bh1710fvc-e.pdf
> + * http://rohmfs.rohm.com/en/products/databook/datasheet/ic/sensor/light/bh1715fvc-e.pdf
> + * http://rohmfs.rohm.com/en/products/databook/datasheet/ic/sensor/light/bh1721fvc-e.pdf
> + * http://rohmfs.rohm.com/en/products/databook/datasheet/ic/sensor/light/bh1750fvi-e.pdf
> + * http://rohmfs.rohm.com/en/products/databook/datasheet/ic/sensor/light/bh1751fvi-e.pdf
> + *
> + * 7-bit I2C slave addresses:
> + * 0x23 (ADDR pin low)
> + * 0x5C (ADDR pin high)
> + *
> + */
> +
> +#include <linux/delay.h>
> +#include <linux/i2c.h>
> +#include <linux/iio/iio.h>
> +#include <linux/iio/sysfs.h>
> +#include <linux/module.h>
> +
> +#define BH1750_POWER_DOWN 0x00
> +#define BH1750_H_RES_MODE 0x10 /* auto-mode for BH1721 */
> +#define BH1750_CHANGE_INT_TIME_H_BIT 0x40
> +#define BH1750_CHANGE_INT_TIME_L_BIT 0x60
> +
> +enum {
> + BH1710,
> + BH1715,
> + BH1721,
> + BH1750,
> + BH1751
> +};
> +
> +struct bh1750_chip_info {
> + int id;
why is the id stored in chip_info?
the point of the chip_info table is to avoid switch blocks in the driver;
I suggest to move remaining chip-dependent values to the table and drop
the id
> + int mtreg_min;
> + int mtreg_max;
> + int mtreg_default;
u16, these are values stored in an u16 register
> + int mtreg_to_usec;
> + int mtreg_to_scale;
> +};
> +
> +struct bh1750_data {
> + struct i2c_client *client;
> + struct mutex lock;
> + const struct bh1750_chip_info *chip_info;
> + u16 mtreg;
> +};
> +
> +static const struct bh1750_chip_info chip_info_tbl[] = {
> + [BH1710] = { BH1710, 140, 1022, 300, 400, 4000 },
> + [BH1715] = { BH1715, 31, 254, 69, 1740, 17391 },
> + [BH1721] = { BH1721, 140, 1020, 300, 400, 4000 },
> + [BH1750] = { BH1750, 31, 254, 69, 1740, 17391 },
> + [BH1751] = { BH1751, 31, 254, 69, 1740, 17391 }
> +};
> +
> +static int bh1750_change_int_time(struct bh1750_data *data, int usec)
> +{
> + int ret, val;
> + u8 low = 0, high = 0;
initialization not needed, low/high should always be set
> + const struct bh1750_chip_info *chip_info = data->chip_info;
> +
> + if ((usec % chip_info->mtreg_to_usec) != 0)
> + return -EINVAL;
> +
> + val = usec / chip_info->mtreg_to_usec;
> + if (val < chip_info->mtreg_min || val > chip_info->mtreg_max)
> + return -EINVAL;
> +
> + switch (chip_info->id) {
> + case BH1710:
> + low = val & 0x001F;
> + high = (val & 0x03E0) >> 5;
> + break;
> + case BH1721:
> + low = val & 0x0010;
> + high = (val & 0x03E0) >> 5;
break missing?
> + case BH1715:
> + case BH1750:
> + case BH1751:
> + low = val & 0x001F;
> + high = (val & 0x00E0) >> 5;
> + break;
> + }
> +
> + ret = i2c_smbus_write_byte(data->client, BH1750_POWER_DOWN);
> + if (ret < 0)
> + return ret;
> +
> + ret = i2c_smbus_write_byte(data->client,
> + BH1750_CHANGE_INT_TIME_H_BIT | high);
> + if (ret < 0)
> + return ret;
> +
> + ret = i2c_smbus_write_byte(data->client,
> + BH1750_CHANGE_INT_TIME_L_BIT | low);
> + if (ret < 0)
> + return ret;
> +
> + data->mtreg = val;
> +
> + return i2c_smbus_write_byte(data->client, BH1750_H_RES_MODE);
> +}
> +
> +static int bh1750_read_raw(struct iio_dev *indio_dev,
> + struct iio_chan_spec const *chan,
> + int *val, int *val2, long mask)
> +{
> + u16 result;
> + int ret, tmp;
> + unsigned long delay;
> + struct bh1750_data *data = iio_priv(indio_dev);
> + const struct bh1750_chip_info *chip_info = data->chip_info;
> +
> + switch (mask) {
> + case IIO_CHAN_INFO_RAW:
> + switch (chan->type) {
> + case IIO_INTENSITY:
> + delay = chip_info->mtreg_to_usec * data->mtreg;
> + mutex_lock(&data->lock);
> + usleep_range(delay, delay + 20000);
the driver uses continuous mode and there is no data-ready flag
why not using one time mode?, I think this would better fit in what other
drivers are doing
> + ret = i2c_master_recv(data->client,
> + (char *)&result, 2);
almost all drivers use i2c_smbus_read_word_xxx() -- is there a reason not
to?
> + mutex_unlock(&data->lock);
> + if (ret < 0)
> + return ret;
> +
> + *val = swab16(result);
> + return IIO_VAL_INT;
> + default:
> + return -EINVAL;
> + }
> + case IIO_CHAN_INFO_SCALE:
> + tmp = chip_info->mtreg_to_scale * data->mtreg;
use the variable delay as above; the same computation is done in every
switch case
> + *val = tmp / 1000000;
> + *val2 = tmp % 1000000;
> + return IIO_VAL_INT_PLUS_MICRO;
> + case IIO_CHAN_INFO_INT_TIME:
> + *val = 0;
> + *val2 = chip_info->mtreg_to_usec * data->mtreg;
> + return IIO_VAL_INT_PLUS_MICRO;
> + default:
> + return -EINVAL;
> + }
> +}
> +
> +static int bh1750_write_raw(struct iio_dev *indio_dev,
> + struct iio_chan_spec const *chan,
> + int val, int val2, long mask)
> +{
> + int ret;
> + struct bh1750_data *data = iio_priv(indio_dev);
> +
> + switch (mask) {
> + case IIO_CHAN_INFO_INT_TIME:
> + if (val != 0)
> + return -EINVAL;
> +
> + mutex_lock(&data->lock);
> + ret = bh1750_change_int_time(data, val2);
> + mutex_unlock(&data->lock);
> + return ret;
> + default:
> + return -EINVAL;
> + }
> +}
> +
> +static ssize_t bh1750_show_int_time_available(struct device *dev,
> + struct device_attribute *attr, char *buf)
> +{
> + int i, inc;
> + size_t len = 0;
> + struct bh1750_data *data = iio_priv(dev_to_iio_dev(dev));
> + const struct bh1750_chip_info *chip_info = data->chip_info;
> +
> + switch (chip_info->id) {
> + case BH1710:
> + case BH1721:
> + /* All values won't fit into one page, so display every
> + * second one. By doing so step size is increased
> + * from 0.4ms to 0.8ms.*/
multi-line comment style?;
missing space before */
> + inc = 2;
> + break;
> + default:
> + inc = 1;
> + break;
> + }
> +
> + for (i = chip_info->mtreg_min; i <= chip_info->mtreg_max; i += inc)
> + len += scnprintf(buf + len, PAGE_SIZE - len, "0.%06d ",
> + i * chip_info->mtreg_to_usec);
> +
> + buf[len - 1] = '\n';
> +
> + return len;
> +}
> +
> +static IIO_DEV_ATTR_INT_TIME_AVAIL(bh1750_show_int_time_available);
> +
> +static struct attribute *bh1750_attributes[] = {
> + &iio_dev_attr_integration_time_available.dev_attr.attr,
> + NULL,
> +};
> +
> +static struct attribute_group bh1750_attribute_group = {
> + .attrs = bh1750_attributes,
> +};
> +
> +static const struct iio_info bh1750_info = {
> + .driver_module = THIS_MODULE,
> + .attrs = &bh1750_attribute_group,
> + .read_raw = bh1750_read_raw,
> + .write_raw = bh1750_write_raw,
> +};
> +
> +static const struct iio_chan_spec bh1750_channels[] = {
> + {
> + .type = IIO_INTENSITY,
> + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
> + BIT(IIO_CHAN_INFO_SCALE) |
> + BIT(IIO_CHAN_INFO_INT_TIME)
> + }
> +};
> +
> +static int bh1750_probe(struct i2c_client *client,
> + const struct i2c_device_id *id)
> +{
> + int ret, usec;
> + struct bh1750_data *data;
> + struct iio_dev *indio_dev;
> +
> + if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C |
> + I2C_FUNC_SMBUS_WRITE_BYTE))
> + return -ENODEV;
> +
> + indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data));
> + if (!indio_dev)
> + return -ENOMEM;
> +
> + data = iio_priv(indio_dev);
> + i2c_set_clientdata(client, indio_dev);
> + data->client = client;
> + data->chip_info = &chip_info_tbl[id->driver_data];
> +
> + usec = data->chip_info->mtreg_to_usec * data->chip_info->mtreg_default;
> + ret = bh1750_change_int_time(data, usec);
> + if (ret < 0)
> + return ret;
> +
> + mutex_init(&data->lock);
> + indio_dev->dev.parent = &client->dev;
> + indio_dev->info = &bh1750_info;
> + indio_dev->name = id->name;
> + indio_dev->channels = bh1750_channels;
> + indio_dev->num_channels = ARRAY_SIZE(bh1750_channels);
> + indio_dev->modes = INDIO_DIRECT_MODE;
> +
> + return devm_iio_device_register(&client->dev, indio_dev);
chip should probably be powered down if this fails; or use one-time mode
> +}
> +
> +#ifdef CONFIG_PM_SLEEP
> +static int bh1750_suspend(struct device *dev)
> +{
> + int ret;
> + struct bh1750_data *data =
> + iio_priv(i2c_get_clientdata(to_i2c_client(dev)));
> +
> + mutex_lock(&data->lock);
> + ret = i2c_smbus_write_byte(data->client, BH1750_POWER_DOWN);
> + mutex_unlock(&data->lock);
> +
> + return ret;
> +}
> +
> +static int bh1750_resume(struct device *dev)
> +{
> + struct bh1750_data *data =
> + iio_priv(i2c_get_clientdata(to_i2c_client(dev)));
> +
> + return i2c_smbus_write_byte(data->client, BH1750_H_RES_MODE);
> +}
> +
> +static SIMPLE_DEV_PM_OPS(bh1750_pm_ops, bh1750_suspend, bh1750_resume);
> +#define BH1750_PM_OPS (&bh1750_pm_ops)
> +#else
> +#define BH1750_PM_OPS NULL
> +#endif
> +
> +static const struct i2c_device_id bh1750_id[] = {
> + { "bh1710", BH1710 },
> + { "bh1715", BH1715 },
> + { "bh1721", BH1721 },
> + { "bh1750", BH1750 },
> + { "bh1751", BH1751 },
> + { }
> +};
> +MODULE_DEVICE_TABLE(i2c, bh1750_id);
> +
> +static struct i2c_driver bh1750_driver = {
> + .driver = {
> + .name = "bh1750",
> + .owner = THIS_MODULE,
> + .pm = BH1750_PM_OPS,
> + },
.remove to power down
> + .probe = bh1750_probe,
> + .id_table = bh1750_id,
> +
> +};
> +module_i2c_driver(bh1750_driver);
> +
> +MODULE_AUTHOR("Tomasz Duszynski <[email protected]>");
> +MODULE_DESCRIPTION("ROHM BH1710/BH1715/BH1721/BH1750/BH1751 als driver");
> +MODULE_LICENSE("GPL v2");
>
--
Peter Meerwald
+43-664-2444418 (mobile)
On Wed, Apr 22, 2015 at 10:49:21AM +0200, Peter Meerwald wrote:
> On Tue, 21 Apr 2015, Tomasz Duszynski wrote:
>
> > Add support for ROHM BH1710/BH1715/BH1721/BH1750/BH1751 ambient light
> > sensors.
>
> nice, some comments inline
>
> > Signed-off-by: Tomasz Duszynski <[email protected]>
> > ---
> > drivers/iio/light/Kconfig | 10 ++
> > drivers/iio/light/Makefile | 1 +
> > drivers/iio/light/bh1750.c | 322 +++++++++++++++++++++++++++++++++++++++++++++
> > 3 files changed, 333 insertions(+)
> > create mode 100644 drivers/iio/light/bh1750.c
> >
> > diff --git a/drivers/iio/light/Kconfig b/drivers/iio/light/Kconfig
> > index 5a3237b..9fb79ca 100644
> > --- a/drivers/iio/light/Kconfig
> > +++ b/drivers/iio/light/Kconfig
> > @@ -37,6 +37,16 @@ config APDS9300
> > To compile this driver as a module, choose M here: the
> > module will be called apds9300.
> >
> > +config BH1750
> > + tristate "BH1750 ambient light sensor"
> > + depends on I2C
> > + help
> > + Say Y here to build support for the BH1710, BH1715, BH1721,
> > + BH1750, BH1751 ambient light sensors.
> > +
> > + To compile this driver as a module, choose M here: the module will
> > + be called bh1750.
> > +
> > config CM32181
> > depends on I2C
> > tristate "CM32181 driver"
> > diff --git a/drivers/iio/light/Makefile b/drivers/iio/light/Makefile
> > index 74656c1..1a13184 100644
> > --- a/drivers/iio/light/Makefile
> > +++ b/drivers/iio/light/Makefile
> > @@ -6,6 +6,7 @@
> > obj-$(CONFIG_ADJD_S311) += adjd_s311.o
> > obj-$(CONFIG_AL3320A) += al3320a.o
> > obj-$(CONFIG_APDS9300) += apds9300.o
> > +obj-$(CONFIG_BH1750) += bh1750.o
> > obj-$(CONFIG_CM32181) += cm32181.o
> > obj-$(CONFIG_CM36651) += cm36651.o
> > obj-$(CONFIG_GP2AP020A00F) += gp2ap020a00f.o
> > diff --git a/drivers/iio/light/bh1750.c b/drivers/iio/light/bh1750.c
> > new file mode 100644
> > index 0000000..83b5413
> > --- /dev/null
> > +++ b/drivers/iio/light/bh1750.c
> > @@ -0,0 +1,322 @@
> > +/*
> > + * ROHM BH1710/BH1715/BH1721/BH1750/BH1751 ambient light sensor driver
> > + *
> > + * Copyright (c) Tomasz Duszynski <[email protected]>
> > + *
> > + * This program is free software; you can redistribute it and/or modify
> > + * it under the terms of the GNU General Public License version 2 as
> > + * published by the Free Software Foundation.
> > + *
> > + * Data sheets:
> > + * http://rohmfs.rohm.com/en/products/databook/datasheet/ic/sensor/light/bh1710fvc-e.pdf
> > + * http://rohmfs.rohm.com/en/products/databook/datasheet/ic/sensor/light/bh1715fvc-e.pdf
> > + * http://rohmfs.rohm.com/en/products/databook/datasheet/ic/sensor/light/bh1721fvc-e.pdf
> > + * http://rohmfs.rohm.com/en/products/databook/datasheet/ic/sensor/light/bh1750fvi-e.pdf
> > + * http://rohmfs.rohm.com/en/products/databook/datasheet/ic/sensor/light/bh1751fvi-e.pdf
> > + *
> > + * 7-bit I2C slave addresses:
> > + * 0x23 (ADDR pin low)
> > + * 0x5C (ADDR pin high)
> > + *
> > + */
> > +
> > +#include <linux/delay.h>
> > +#include <linux/i2c.h>
> > +#include <linux/iio/iio.h>
> > +#include <linux/iio/sysfs.h>
> > +#include <linux/module.h>
> > +
> > +#define BH1750_POWER_DOWN 0x00
> > +#define BH1750_H_RES_MODE 0x10 /* auto-mode for BH1721 */
> > +#define BH1750_CHANGE_INT_TIME_H_BIT 0x40
> > +#define BH1750_CHANGE_INT_TIME_L_BIT 0x60
> > +
> > +enum {
> > + BH1710,
> > + BH1715,
> > + BH1721,
> > + BH1750,
> > + BH1751
> > +};
> > +
> > +struct bh1750_chip_info {
> > + int id;
>
> why is the id stored in chip_info?
> the point of the chip_info table is to avoid switch blocks in the driver;
> I suggest to move remaining chip-dependent values to the table and drop
> the id
>
OK.
> > + int mtreg_min;
> > + int mtreg_max;
> > + int mtreg_default;
>
> u16, these are values stored in an u16 register
>
Right. Will fix that.
> > + int mtreg_to_usec;
> > + int mtreg_to_scale;
> > +};
> > +
> > +struct bh1750_data {
> > + struct i2c_client *client;
> > + struct mutex lock;
> > + const struct bh1750_chip_info *chip_info;
> > + u16 mtreg;
> > +};
> > +
> > +static const struct bh1750_chip_info chip_info_tbl[] = {
> > + [BH1710] = { BH1710, 140, 1022, 300, 400, 4000 },
> > + [BH1715] = { BH1715, 31, 254, 69, 1740, 17391 },
> > + [BH1721] = { BH1721, 140, 1020, 300, 400, 4000 },
> > + [BH1750] = { BH1750, 31, 254, 69, 1740, 17391 },
> > + [BH1751] = { BH1751, 31, 254, 69, 1740, 17391 }
> > +};
> > +
> > +static int bh1750_change_int_time(struct bh1750_data *data, int usec)
> > +{
> > + int ret, val;
> > + u8 low = 0, high = 0;
>
> initialization not needed, low/high should always be set
>
The idea was to make gcc stop complaining that some values
can be uninitialized. Will change that in next patch.
> > + const struct bh1750_chip_info *chip_info = data->chip_info;
> > +
> > + if ((usec % chip_info->mtreg_to_usec) != 0)
> > + return -EINVAL;
> > +
> > + val = usec / chip_info->mtreg_to_usec;
> > + if (val < chip_info->mtreg_min || val > chip_info->mtreg_max)
> > + return -EINVAL;
> > +
> > + switch (chip_info->id) {
> > + case BH1710:
> > + low = val & 0x001F;
> > + high = (val & 0x03E0) >> 5;
> > + break;
> > + case BH1721:
> > + low = val & 0x0010;
> > + high = (val & 0x03E0) >> 5;
>
> break missing?
>
Right.
> > + case BH1715:
> > + case BH1750:
> > + case BH1751:
> > + low = val & 0x001F;
> > + high = (val & 0x00E0) >> 5;
> > + break;
> > + }
> > +
> > + ret = i2c_smbus_write_byte(data->client, BH1750_POWER_DOWN);
> > + if (ret < 0)
> > + return ret;
> > +
> > + ret = i2c_smbus_write_byte(data->client,
> > + BH1750_CHANGE_INT_TIME_H_BIT | high);
> > + if (ret < 0)
> > + return ret;
> > +
> > + ret = i2c_smbus_write_byte(data->client,
> > + BH1750_CHANGE_INT_TIME_L_BIT | low);
> > + if (ret < 0)
> > + return ret;
> > +
> > + data->mtreg = val;
> > +
> > + return i2c_smbus_write_byte(data->client, BH1750_H_RES_MODE);
> > +}
> > +
> > +static int bh1750_read_raw(struct iio_dev *indio_dev,
> > + struct iio_chan_spec const *chan,
> > + int *val, int *val2, long mask)
> > +{
> > + u16 result;
> > + int ret, tmp;
> > + unsigned long delay;
> > + struct bh1750_data *data = iio_priv(indio_dev);
> > + const struct bh1750_chip_info *chip_info = data->chip_info;
> > +
> > + switch (mask) {
> > + case IIO_CHAN_INFO_RAW:
> > + switch (chan->type) {
> > + case IIO_INTENSITY:
> > + delay = chip_info->mtreg_to_usec * data->mtreg;
> > + mutex_lock(&data->lock);
> > + usleep_range(delay, delay + 20000);
>
> the driver uses continuous mode and there is no data-ready flag
>
> why not using one time mode?, I think this would better fit in what other
> drivers are doing
>
One time mode is not supported by all chips. It was just easier to use
mode that fits all. Anyway, I will rethink that part.
> > + ret = i2c_master_recv(data->client,
> > + (char *)&result, 2);
>
> almost all drivers use i2c_smbus_read_word_xxx() -- is there a reason not
> to?
>
Yes. In BH17xx case you address device and then read two bytes with
measurement result - no sending additional command in between.
> > + mutex_unlock(&data->lock);
> > + if (ret < 0)
> > + return ret;
> > +
> > + *val = swab16(result);
> > + return IIO_VAL_INT;
> > + default:
> > + return -EINVAL;
> > + }
> > + case IIO_CHAN_INFO_SCALE:
> > + tmp = chip_info->mtreg_to_scale * data->mtreg;
>
> use the variable delay as above; the same computation is done in every
> switch case
>
OK.
> > + *val = tmp / 1000000;
> > + *val2 = tmp % 1000000;
> > + return IIO_VAL_INT_PLUS_MICRO;
> > + case IIO_CHAN_INFO_INT_TIME:
> > + *val = 0;
> > + *val2 = chip_info->mtreg_to_usec * data->mtreg;
> > + return IIO_VAL_INT_PLUS_MICRO;
> > + default:
> > + return -EINVAL;
> > + }
> > +}
> > +
> > +static int bh1750_write_raw(struct iio_dev *indio_dev,
> > + struct iio_chan_spec const *chan,
> > + int val, int val2, long mask)
> > +{
> > + int ret;
> > + struct bh1750_data *data = iio_priv(indio_dev);
> > +
> > + switch (mask) {
> > + case IIO_CHAN_INFO_INT_TIME:
> > + if (val != 0)
> > + return -EINVAL;
> > +
> > + mutex_lock(&data->lock);
> > + ret = bh1750_change_int_time(data, val2);
> > + mutex_unlock(&data->lock);
> > + return ret;
> > + default:
> > + return -EINVAL;
> > + }
> > +}
> > +
> > +static ssize_t bh1750_show_int_time_available(struct device *dev,
> > + struct device_attribute *attr, char *buf)
> > +{
> > + int i, inc;
> > + size_t len = 0;
> > + struct bh1750_data *data = iio_priv(dev_to_iio_dev(dev));
> > + const struct bh1750_chip_info *chip_info = data->chip_info;
> > +
> > + switch (chip_info->id) {
> > + case BH1710:
> > + case BH1721:
> > + /* All values won't fit into one page, so display every
> > + * second one. By doing so step size is increased
> > + * from 0.4ms to 0.8ms.*/
>
> multi-line comment style?;
> missing space before */
>
Right.
> > + inc = 2;
> > + break;
> > + default:
> > + inc = 1;
> > + break;
> > + }
> > +
> > + for (i = chip_info->mtreg_min; i <= chip_info->mtreg_max; i += inc)
> > + len += scnprintf(buf + len, PAGE_SIZE - len, "0.%06d ",
> > + i * chip_info->mtreg_to_usec);
> > +
> > + buf[len - 1] = '\n';
> > +
> > + return len;
> > +}
> > +
> > +static IIO_DEV_ATTR_INT_TIME_AVAIL(bh1750_show_int_time_available);
> > +
> > +static struct attribute *bh1750_attributes[] = {
> > + &iio_dev_attr_integration_time_available.dev_attr.attr,
> > + NULL,
> > +};
> > +
> > +static struct attribute_group bh1750_attribute_group = {
> > + .attrs = bh1750_attributes,
> > +};
> > +
> > +static const struct iio_info bh1750_info = {
> > + .driver_module = THIS_MODULE,
> > + .attrs = &bh1750_attribute_group,
> > + .read_raw = bh1750_read_raw,
> > + .write_raw = bh1750_write_raw,
> > +};
> > +
> > +static const struct iio_chan_spec bh1750_channels[] = {
> > + {
> > + .type = IIO_INTENSITY,
> > + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
> > + BIT(IIO_CHAN_INFO_SCALE) |
> > + BIT(IIO_CHAN_INFO_INT_TIME)
> > + }
> > +};
> > +
> > +static int bh1750_probe(struct i2c_client *client,
> > + const struct i2c_device_id *id)
> > +{
> > + int ret, usec;
> > + struct bh1750_data *data;
> > + struct iio_dev *indio_dev;
> > +
> > + if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C |
> > + I2C_FUNC_SMBUS_WRITE_BYTE))
> > + return -ENODEV;
> > +
> > + indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data));
> > + if (!indio_dev)
> > + return -ENOMEM;
> > +
> > + data = iio_priv(indio_dev);
> > + i2c_set_clientdata(client, indio_dev);
> > + data->client = client;
> > + data->chip_info = &chip_info_tbl[id->driver_data];
> > +
> > + usec = data->chip_info->mtreg_to_usec * data->chip_info->mtreg_default;
> > + ret = bh1750_change_int_time(data, usec);
> > + if (ret < 0)
> > + return ret;
> > +
> > + mutex_init(&data->lock);
> > + indio_dev->dev.parent = &client->dev;
> > + indio_dev->info = &bh1750_info;
> > + indio_dev->name = id->name;
> > + indio_dev->channels = bh1750_channels;
> > + indio_dev->num_channels = ARRAY_SIZE(bh1750_channels);
> > + indio_dev->modes = INDIO_DIRECT_MODE;
> > +
> > + return devm_iio_device_register(&client->dev, indio_dev);
>
> chip should probably be powered down if this fails; or use one-time mode
>
OK.
> > +}
> > +
> > +#ifdef CONFIG_PM_SLEEP
> > +static int bh1750_suspend(struct device *dev)
> > +{
> > + int ret;
> > + struct bh1750_data *data =
> > + iio_priv(i2c_get_clientdata(to_i2c_client(dev)));
> > +
> > + mutex_lock(&data->lock);
> > + ret = i2c_smbus_write_byte(data->client, BH1750_POWER_DOWN);
> > + mutex_unlock(&data->lock);
> > +
> > + return ret;
> > +}
> > +
> > +static int bh1750_resume(struct device *dev)
> > +{
> > + struct bh1750_data *data =
> > + iio_priv(i2c_get_clientdata(to_i2c_client(dev)));
> > +
> > + return i2c_smbus_write_byte(data->client, BH1750_H_RES_MODE);
> > +}
> > +
> > +static SIMPLE_DEV_PM_OPS(bh1750_pm_ops, bh1750_suspend, bh1750_resume);
> > +#define BH1750_PM_OPS (&bh1750_pm_ops)
> > +#else
> > +#define BH1750_PM_OPS NULL
> > +#endif
> > +
> > +static const struct i2c_device_id bh1750_id[] = {
> > + { "bh1710", BH1710 },
> > + { "bh1715", BH1715 },
> > + { "bh1721", BH1721 },
> > + { "bh1750", BH1750 },
> > + { "bh1751", BH1751 },
> > + { }
> > +};
> > +MODULE_DEVICE_TABLE(i2c, bh1750_id);
> > +
> > +static struct i2c_driver bh1750_driver = {
> > + .driver = {
> > + .name = "bh1750",
> > + .owner = THIS_MODULE,
> > + .pm = BH1750_PM_OPS,
> > + },
>
> .remove to power down
>
OK.
> > + .probe = bh1750_probe,
> > + .id_table = bh1750_id,
> > +
> > +};
> > +module_i2c_driver(bh1750_driver);
> > +
> > +MODULE_AUTHOR("Tomasz Duszynski <[email protected]>");
> > +MODULE_DESCRIPTION("ROHM BH1710/BH1715/BH1721/BH1750/BH1751 als driver");
> > +MODULE_LICENSE("GPL v2");
> >
>
> --
>
> Peter Meerwald
> +43-664-2444418 (mobile)
Thanks for review!
On Tue, Apr 21, 2015 at 9:43 PM, Tomasz Duszynski <[email protected]> wrote:
> Add support for ROHM BH1710/BH1715/BH1721/BH1750/BH1751 ambient light
> sensors.
>
> Signed-off-by: Tomasz Duszynski <[email protected]>
> ---
> drivers/iio/light/Kconfig | 10 ++
> drivers/iio/light/Makefile | 1 +
> drivers/iio/light/bh1750.c | 322 +++++++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 333 insertions(+)
> create mode 100644 drivers/iio/light/bh1750.c
>
> diff --git a/drivers/iio/light/Kconfig b/drivers/iio/light/Kconfig
> index 5a3237b..9fb79ca 100644
> --- a/drivers/iio/light/Kconfig
> +++ b/drivers/iio/light/Kconfig
> @@ -37,6 +37,16 @@ config APDS9300
> To compile this driver as a module, choose M here: the
> module will be called apds9300.
>
> +config BH1750
> + tristate "BH1750 ambient light sensor"
Better use ROHM BH1750 .. here.
> +static const struct iio_chan_spec bh1750_channels[] = {
> + {
> + .type = IIO_INTENSITY,
Shouldn't this be IIO_LIGHT channel type?
Users will get illuminance after multiplying raw value with scale.
> + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
> + BIT(IIO_CHAN_INFO_SCALE) |
> + BIT(IIO_CHAN_INFO_INT_TIME)
> + }
> +};
> +
> +static int bh1750_probe(struct i2c_client *client,
> + const struct i2c_device_id *id)
> +{
> + int ret, usec;
> + struct bh1750_data *data;
> + struct iio_dev *indio_dev;
> +
> + if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C |
> + I2C_FUNC_SMBUS_WRITE_BYTE))
> + return -ENODEV;
> +
> + indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data));
> + if (!indio_dev)
> + return -ENOMEM;
> +
> + data = iio_priv(indio_dev);
> + i2c_set_clientdata(client, indio_dev);
> + data->client = client;
> + data->chip_info = &chip_info_tbl[id->driver_data];
> +
> + usec = data->chip_info->mtreg_to_usec * data->chip_info->mtreg_default;
> + ret = bh1750_change_int_time(data, usec);
> + if (ret < 0)
> + return ret;
> +
> + mutex_init(&data->lock);
> + indio_dev->dev.parent = &client->dev;
> + indio_dev->info = &bh1750_info;
> + indio_dev->name = id->name;
> + indio_dev->channels = bh1750_channels;
> + indio_dev->num_channels = ARRAY_SIZE(bh1750_channels);
> + indio_dev->modes = INDIO_DIRECT_MODE;
> +
> + return devm_iio_device_register(&client->dev, indio_dev);
You need also to add a remove function where the chip is powered down. Then
you shouldn't use devm_iio_device_register here, because you need to control
the order of chip powerdown/ device unregister operations at remove.
thanks,
Daniel.
On Thu, Apr 23, 2015 at 10:30:09AM +0300, Daniel Baluta wrote:
> On Tue, Apr 21, 2015 at 9:43 PM, Tomasz Duszynski <[email protected]> wrote:
> > Add support for ROHM BH1710/BH1715/BH1721/BH1750/BH1751 ambient light
> > sensors.
> >
> > Signed-off-by: Tomasz Duszynski <[email protected]>
> > ---
> > drivers/iio/light/Kconfig | 10 ++
> > drivers/iio/light/Makefile | 1 +
> > drivers/iio/light/bh1750.c | 322 +++++++++++++++++++++++++++++++++++++++++++++
> > 3 files changed, 333 insertions(+)
> > create mode 100644 drivers/iio/light/bh1750.c
> >
> > diff --git a/drivers/iio/light/Kconfig b/drivers/iio/light/Kconfig
> > index 5a3237b..9fb79ca 100644
> > --- a/drivers/iio/light/Kconfig
> > +++ b/drivers/iio/light/Kconfig
> > @@ -37,6 +37,16 @@ config APDS9300
> > To compile this driver as a module, choose M here: the
> > module will be called apds9300.
> >
> > +config BH1750
> > + tristate "BH1750 ambient light sensor"
>
> Better use ROHM BH1750 .. here.
>
>
Did git blame on Kconfig and among newest sensors some
have this manufacturer prefix while others don't, but still no problem
for me to add that.
> > +static const struct iio_chan_spec bh1750_channels[] = {
> > + {
> > + .type = IIO_INTENSITY,
>
> Shouldn't this be IIO_LIGHT channel type?
>
> Users will get illuminance after multiplying raw value with scale.
>
That naming is misleading. Thanks for pointing this out.
> > + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
> > + BIT(IIO_CHAN_INFO_SCALE) |
> > + BIT(IIO_CHAN_INFO_INT_TIME)
> > + }
> > +};
> > +
> > +static int bh1750_probe(struct i2c_client *client,
> > + const struct i2c_device_id *id)
> > +{
> > + int ret, usec;
> > + struct bh1750_data *data;
> > + struct iio_dev *indio_dev;
> > +
> > + if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C |
> > + I2C_FUNC_SMBUS_WRITE_BYTE))
> > + return -ENODEV;
> > +
> > + indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data));
> > + if (!indio_dev)
> > + return -ENOMEM;
> > +
> > + data = iio_priv(indio_dev);
> > + i2c_set_clientdata(client, indio_dev);
> > + data->client = client;
> > + data->chip_info = &chip_info_tbl[id->driver_data];
> > +
> > + usec = data->chip_info->mtreg_to_usec * data->chip_info->mtreg_default;
> > + ret = bh1750_change_int_time(data, usec);
> > + if (ret < 0)
> > + return ret;
> > +
> > + mutex_init(&data->lock);
> > + indio_dev->dev.parent = &client->dev;
> > + indio_dev->info = &bh1750_info;
> > + indio_dev->name = id->name;
> > + indio_dev->channels = bh1750_channels;
> > + indio_dev->num_channels = ARRAY_SIZE(bh1750_channels);
> > + indio_dev->modes = INDIO_DIRECT_MODE;
> > +
> > + return devm_iio_device_register(&client->dev, indio_dev);
>
> You need also to add a remove function where the chip is powered down. Then
> you shouldn't use devm_iio_device_register here, because you need to control
> the order of chip powerdown/ device unregister operations at remove.
>
Right.
> thanks,
> Daniel.
Thanks for review!