From: Yakir Yang <[email protected]>
When transmitting IEC60985 linear PCM audio, we configure the
Aduio Sample Channel Status information of all the channel
status bits in the IEC60958 frame.
Refer to 60958-3 page 10 for frequency, original frequency, and
wordlength setting.
This fix the issue that audio does not come out on some monitors
(e.g. LG 22CV241)
Note that these registers are only for interfaces:
I2S audio interface, General Purpose Audio (GPA), or AHB audio DMA
(AHBAUDDMA).
For S/PDIF interface this information comes from the stream.
Currently this function dw_hdmi_set_channel_status is only called
from dw-hdmi-i2s-audio in I2S setup.
Signed-off-by: Yakir Yang <[email protected]>
Signed-off-by: Cheng-Yi Chiang <[email protected]>
---
Original patch by Yakir Yang is at
https://lore.kernel.org/patchwork/patch/539653/
Change from v1 to v2:
1. Remove the version check because this will only be called by
dw-hdmi-i2s-audio, and the registers are available in I2S setup.
2. Set these registers in dw_hdmi_i2s_hw_params.
3. Fix the sample width setting so it can use 16 or 24 bits.
.../drm/bridge/synopsys/dw-hdmi-i2s-audio.c | 1 +
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 70 +++++++++++++++++++
drivers/gpu/drm/bridge/synopsys/dw-hdmi.h | 20 ++++++
include/drm/bridge/dw_hdmi.h | 2 +
4 files changed, 93 insertions(+)
diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi-i2s-audio.c b/drivers/gpu/drm/bridge/synopsys/dw-hdmi-i2s-audio.c
index 34d8e837555f..b801a28b0f17 100644
--- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi-i2s-audio.c
+++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi-i2s-audio.c
@@ -102,6 +102,7 @@ static int dw_hdmi_i2s_hw_params(struct device *dev, void *data,
}
dw_hdmi_set_sample_rate(hdmi, hparms->sample_rate);
+ dw_hdmi_set_channel_status(hdmi, hparms->sample_width);
dw_hdmi_set_channel_count(hdmi, hparms->channels);
dw_hdmi_set_channel_allocation(hdmi, hparms->cea.channel_allocation);
diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
index bd65d0479683..d1daa369c8ae 100644
--- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
+++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
@@ -582,6 +582,76 @@ static unsigned int hdmi_compute_n(unsigned int freq, unsigned long pixel_clk)
return n;
}
+/*
+ * When transmitting IEC60958 linear PCM audio, these registers allow to
+ * configure the channel status information of all the channel status
+ * bits in the IEC60958 frame. For the moment this configuration is only
+ * used when the I2S audio interface, General Purpose Audio (GPA),
+ * or AHB audio DMA (AHBAUDDMA) interface is active
+ * (for S/PDIF interface this information comes from the stream).
+ */
+void dw_hdmi_set_channel_status(struct dw_hdmi *hdmi,
+ unsigned int sample_width)
+{
+ u8 aud_schnl_samplerate;
+ u8 aud_schnl_8;
+ u8 word_length_bits;
+
+ switch (hdmi->sample_rate) {
+ case 32000:
+ aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_32K;
+ break;
+ case 44100:
+ aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_44K1;
+ break;
+ case 48000:
+ aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_48K;
+ break;
+ case 88200:
+ aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_88K2;
+ break;
+ case 96000:
+ aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_96K;
+ break;
+ case 176400:
+ aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_176K4;
+ break;
+ case 192000:
+ aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_192K;
+ break;
+ case 768000:
+ aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_768K;
+ break;
+ default:
+ dev_warn(hdmi->dev, "Unsupported audio sample rate (%u)\n",
+ hdmi->sample_rate);
+ return;
+ }
+
+ /* set channel status register */
+ hdmi_modb(hdmi, aud_schnl_samplerate, HDMI_FC_AUDSCHNLS7_SMPRATE_MASK,
+ HDMI_FC_AUDSCHNLS7);
+
+ /*
+ * Set original frequency to be the same as frequency.
+ * Use one-complement value as stated in IEC60958-3 page 13.
+ */
+ aud_schnl_8 = (~aud_schnl_samplerate) <<
+ HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_OFFSET;
+
+ /*
+ * Refer to IEC60958-3 page 12. We can accept 16 bits or 24 bits.
+ * Otherwise, set the register to 0t o indicate using default value.
+ */
+ word_length_bits = (sample_width == 16) ? 0x2 :
+ ((sample_width == 24) ? 0xb : 0);
+
+ aud_schnl_8 |= word_length_bits << HDMI_FC_AUDSCHNLS8_WORDLEGNTH_OFFSET;
+
+ hdmi_writeb(hdmi, aud_schnl_8, HDMI_FC_AUDSCHNLS8);
+}
+EXPORT_SYMBOL_GPL(dw_hdmi_set_channel_status);
+
static void hdmi_set_clk_regenerator(struct dw_hdmi *hdmi,
unsigned long pixel_clk, unsigned int sample_rate)
{
diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h
index 6988f12d89d9..619ebc1c8354 100644
--- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h
+++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h
@@ -158,6 +158,17 @@
#define HDMI_FC_SPDDEVICEINF 0x1062
#define HDMI_FC_AUDSCONF 0x1063
#define HDMI_FC_AUDSSTAT 0x1064
+#define HDMI_FC_AUDSV 0x1065
+#define HDMI_FC_AUDSU 0x1066
+#define HDMI_FC_AUDSCHNLS0 0x1067
+#define HDMI_FC_AUDSCHNLS1 0x1068
+#define HDMI_FC_AUDSCHNLS2 0x1069
+#define HDMI_FC_AUDSCHNLS3 0x106a
+#define HDMI_FC_AUDSCHNLS4 0x106b
+#define HDMI_FC_AUDSCHNLS5 0x106c
+#define HDMI_FC_AUDSCHNLS6 0x106d
+#define HDMI_FC_AUDSCHNLS7 0x106e
+#define HDMI_FC_AUDSCHNLS8 0x106f
#define HDMI_FC_DATACH0FILL 0x1070
#define HDMI_FC_DATACH1FILL 0x1071
#define HDMI_FC_DATACH2FILL 0x1072
@@ -706,6 +717,15 @@ enum {
/* HDMI_FC_AUDSCHNLS7 field values */
HDMI_FC_AUDSCHNLS7_ACCURACY_OFFSET = 4,
HDMI_FC_AUDSCHNLS7_ACCURACY_MASK = 0x30,
+ HDMI_FC_AUDSCHNLS7_SMPRATE_MASK = 0x0f,
+ HDMI_FC_AUDSCHNLS7_SMPRATE_192K = 0xe,
+ HDMI_FC_AUDSCHNLS7_SMPRATE_176K4 = 0xc,
+ HDMI_FC_AUDSCHNLS7_SMPRATE_96K = 0xa,
+ HDMI_FC_AUDSCHNLS7_SMPRATE_768K = 0x9,
+ HDMI_FC_AUDSCHNLS7_SMPRATE_88K2 = 0x8,
+ HDMI_FC_AUDSCHNLS7_SMPRATE_32K = 0x3,
+ HDMI_FC_AUDSCHNLS7_SMPRATE_48K = 0x2,
+ HDMI_FC_AUDSCHNLS7_SMPRATE_44K1 = 0x0,
/* HDMI_FC_AUDSCHNLS8 field values */
HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_MASK = 0xf0,
diff --git a/include/drm/bridge/dw_hdmi.h b/include/drm/bridge/dw_hdmi.h
index cf528c289857..12144d2f80f4 100644
--- a/include/drm/bridge/dw_hdmi.h
+++ b/include/drm/bridge/dw_hdmi.h
@@ -156,6 +156,8 @@ void dw_hdmi_setup_rx_sense(struct dw_hdmi *hdmi, bool hpd, bool rx_sense);
void dw_hdmi_set_sample_rate(struct dw_hdmi *hdmi, unsigned int rate);
void dw_hdmi_set_channel_count(struct dw_hdmi *hdmi, unsigned int cnt);
+void dw_hdmi_set_channel_status(struct dw_hdmi *hdmi,
+ unsigned int sample_width);
void dw_hdmi_set_channel_allocation(struct dw_hdmi *hdmi, unsigned int ca);
void dw_hdmi_audio_enable(struct dw_hdmi *hdmi);
void dw_hdmi_audio_disable(struct dw_hdmi *hdmi);
--
2.23.0.187.g17f5b7556c-goog
Sorry for the noise.
Removed original author [email protected] from the thread because
that mail is obsolete.
Yakir is now using [email protected].
On Thu, Sep 5, 2019 at 5:43 PM Cheng-Yi Chiang <[email protected]> wrote:
>
> From: Yakir Yang <[email protected]>
>
> When transmitting IEC60985 linear PCM audio, we configure the
> Aduio Sample Channel Status information of all the channel
> status bits in the IEC60958 frame.
> Refer to 60958-3 page 10 for frequency, original frequency, and
> wordlength setting.
>
> This fix the issue that audio does not come out on some monitors
> (e.g. LG 22CV241)
>
> Note that these registers are only for interfaces:
> I2S audio interface, General Purpose Audio (GPA), or AHB audio DMA
> (AHBAUDDMA).
> For S/PDIF interface this information comes from the stream.
>
> Currently this function dw_hdmi_set_channel_status is only called
> from dw-hdmi-i2s-audio in I2S setup.
>
> Signed-off-by: Yakir Yang <[email protected]>
> Signed-off-by: Cheng-Yi Chiang <[email protected]>
> ---
> Original patch by Yakir Yang is at
>
> https://lore.kernel.org/patchwork/patch/539653/
>
> Change from v1 to v2:
> 1. Remove the version check because this will only be called by
> dw-hdmi-i2s-audio, and the registers are available in I2S setup.
> 2. Set these registers in dw_hdmi_i2s_hw_params.
> 3. Fix the sample width setting so it can use 16 or 24 bits.
>
> .../drm/bridge/synopsys/dw-hdmi-i2s-audio.c | 1 +
> drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 70 +++++++++++++++++++
> drivers/gpu/drm/bridge/synopsys/dw-hdmi.h | 20 ++++++
> include/drm/bridge/dw_hdmi.h | 2 +
> 4 files changed, 93 insertions(+)
>
> diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi-i2s-audio.c b/drivers/gpu/drm/bridge/synopsys/dw-hdmi-i2s-audio.c
> index 34d8e837555f..b801a28b0f17 100644
> --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi-i2s-audio.c
> +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi-i2s-audio.c
> @@ -102,6 +102,7 @@ static int dw_hdmi_i2s_hw_params(struct device *dev, void *data,
> }
>
> dw_hdmi_set_sample_rate(hdmi, hparms->sample_rate);
> + dw_hdmi_set_channel_status(hdmi, hparms->sample_width);
> dw_hdmi_set_channel_count(hdmi, hparms->channels);
> dw_hdmi_set_channel_allocation(hdmi, hparms->cea.channel_allocation);
>
> diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
> index bd65d0479683..d1daa369c8ae 100644
> --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
> +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
> @@ -582,6 +582,76 @@ static unsigned int hdmi_compute_n(unsigned int freq, unsigned long pixel_clk)
> return n;
> }
>
> +/*
> + * When transmitting IEC60958 linear PCM audio, these registers allow to
> + * configure the channel status information of all the channel status
> + * bits in the IEC60958 frame. For the moment this configuration is only
> + * used when the I2S audio interface, General Purpose Audio (GPA),
> + * or AHB audio DMA (AHBAUDDMA) interface is active
> + * (for S/PDIF interface this information comes from the stream).
> + */
> +void dw_hdmi_set_channel_status(struct dw_hdmi *hdmi,
> + unsigned int sample_width)
> +{
> + u8 aud_schnl_samplerate;
> + u8 aud_schnl_8;
> + u8 word_length_bits;
> +
> + switch (hdmi->sample_rate) {
> + case 32000:
> + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_32K;
> + break;
> + case 44100:
> + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_44K1;
> + break;
> + case 48000:
> + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_48K;
> + break;
> + case 88200:
> + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_88K2;
> + break;
> + case 96000:
> + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_96K;
> + break;
> + case 176400:
> + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_176K4;
> + break;
> + case 192000:
> + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_192K;
> + break;
> + case 768000:
> + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_768K;
> + break;
> + default:
> + dev_warn(hdmi->dev, "Unsupported audio sample rate (%u)\n",
> + hdmi->sample_rate);
> + return;
> + }
> +
> + /* set channel status register */
> + hdmi_modb(hdmi, aud_schnl_samplerate, HDMI_FC_AUDSCHNLS7_SMPRATE_MASK,
> + HDMI_FC_AUDSCHNLS7);
> +
> + /*
> + * Set original frequency to be the same as frequency.
> + * Use one-complement value as stated in IEC60958-3 page 13.
> + */
> + aud_schnl_8 = (~aud_schnl_samplerate) <<
> + HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_OFFSET;
> +
> + /*
> + * Refer to IEC60958-3 page 12. We can accept 16 bits or 24 bits.
> + * Otherwise, set the register to 0t o indicate using default value.
> + */
> + word_length_bits = (sample_width == 16) ? 0x2 :
> + ((sample_width == 24) ? 0xb : 0);
> +
> + aud_schnl_8 |= word_length_bits << HDMI_FC_AUDSCHNLS8_WORDLEGNTH_OFFSET;
> +
> + hdmi_writeb(hdmi, aud_schnl_8, HDMI_FC_AUDSCHNLS8);
> +}
> +EXPORT_SYMBOL_GPL(dw_hdmi_set_channel_status);
> +
> static void hdmi_set_clk_regenerator(struct dw_hdmi *hdmi,
> unsigned long pixel_clk, unsigned int sample_rate)
> {
> diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h
> index 6988f12d89d9..619ebc1c8354 100644
> --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h
> +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h
> @@ -158,6 +158,17 @@
> #define HDMI_FC_SPDDEVICEINF 0x1062
> #define HDMI_FC_AUDSCONF 0x1063
> #define HDMI_FC_AUDSSTAT 0x1064
> +#define HDMI_FC_AUDSV 0x1065
> +#define HDMI_FC_AUDSU 0x1066
> +#define HDMI_FC_AUDSCHNLS0 0x1067
> +#define HDMI_FC_AUDSCHNLS1 0x1068
> +#define HDMI_FC_AUDSCHNLS2 0x1069
> +#define HDMI_FC_AUDSCHNLS3 0x106a
> +#define HDMI_FC_AUDSCHNLS4 0x106b
> +#define HDMI_FC_AUDSCHNLS5 0x106c
> +#define HDMI_FC_AUDSCHNLS6 0x106d
> +#define HDMI_FC_AUDSCHNLS7 0x106e
> +#define HDMI_FC_AUDSCHNLS8 0x106f
> #define HDMI_FC_DATACH0FILL 0x1070
> #define HDMI_FC_DATACH1FILL 0x1071
> #define HDMI_FC_DATACH2FILL 0x1072
> @@ -706,6 +717,15 @@ enum {
> /* HDMI_FC_AUDSCHNLS7 field values */
> HDMI_FC_AUDSCHNLS7_ACCURACY_OFFSET = 4,
> HDMI_FC_AUDSCHNLS7_ACCURACY_MASK = 0x30,
> + HDMI_FC_AUDSCHNLS7_SMPRATE_MASK = 0x0f,
> + HDMI_FC_AUDSCHNLS7_SMPRATE_192K = 0xe,
> + HDMI_FC_AUDSCHNLS7_SMPRATE_176K4 = 0xc,
> + HDMI_FC_AUDSCHNLS7_SMPRATE_96K = 0xa,
> + HDMI_FC_AUDSCHNLS7_SMPRATE_768K = 0x9,
> + HDMI_FC_AUDSCHNLS7_SMPRATE_88K2 = 0x8,
> + HDMI_FC_AUDSCHNLS7_SMPRATE_32K = 0x3,
> + HDMI_FC_AUDSCHNLS7_SMPRATE_48K = 0x2,
> + HDMI_FC_AUDSCHNLS7_SMPRATE_44K1 = 0x0,
>
> /* HDMI_FC_AUDSCHNLS8 field values */
> HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_MASK = 0xf0,
> diff --git a/include/drm/bridge/dw_hdmi.h b/include/drm/bridge/dw_hdmi.h
> index cf528c289857..12144d2f80f4 100644
> --- a/include/drm/bridge/dw_hdmi.h
> +++ b/include/drm/bridge/dw_hdmi.h
> @@ -156,6 +156,8 @@ void dw_hdmi_setup_rx_sense(struct dw_hdmi *hdmi, bool hpd, bool rx_sense);
>
> void dw_hdmi_set_sample_rate(struct dw_hdmi *hdmi, unsigned int rate);
> void dw_hdmi_set_channel_count(struct dw_hdmi *hdmi, unsigned int cnt);
> +void dw_hdmi_set_channel_status(struct dw_hdmi *hdmi,
> + unsigned int sample_width);
> void dw_hdmi_set_channel_allocation(struct dw_hdmi *hdmi, unsigned int ca);
> void dw_hdmi_audio_enable(struct dw_hdmi *hdmi);
> void dw_hdmi_audio_disable(struct dw_hdmi *hdmi);
> --
> 2.23.0.187.g17f5b7556c-goog
>
Dne četrtek, 05. september 2019 ob 11:43:25 CEST je Cheng-Yi Chiang
napisal(a):
> From: Yakir Yang <[email protected]>
>
> When transmitting IEC60985 linear PCM audio, we configure the
> Aduio Sample Channel Status information of all the channel
> status bits in the IEC60958 frame.
> Refer to 60958-3 page 10 for frequency, original frequency, and
> wordlength setting.
>
> This fix the issue that audio does not come out on some monitors
> (e.g. LG 22CV241)
>
> Note that these registers are only for interfaces:
> I2S audio interface, General Purpose Audio (GPA), or AHB audio DMA
> (AHBAUDDMA).
> For S/PDIF interface this information comes from the stream.
>
> Currently this function dw_hdmi_set_channel_status is only called
> from dw-hdmi-i2s-audio in I2S setup.
>
> Signed-off-by: Yakir Yang <[email protected]>
> Signed-off-by: Cheng-Yi Chiang <[email protected]>
> ---
> Original patch by Yakir Yang is at
>
> https://lore.kernel.org/patchwork/patch/539653/
>
> Change from v1 to v2:
> 1. Remove the version check because this will only be called by
> dw-hdmi-i2s-audio, and the registers are available in I2S setup.
> 2. Set these registers in dw_hdmi_i2s_hw_params.
> 3. Fix the sample width setting so it can use 16 or 24 bits.
>
> .../drm/bridge/synopsys/dw-hdmi-i2s-audio.c | 1 +
> drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 70 +++++++++++++++++++
> drivers/gpu/drm/bridge/synopsys/dw-hdmi.h | 20 ++++++
> include/drm/bridge/dw_hdmi.h | 2 +
> 4 files changed, 93 insertions(+)
>
> diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi-i2s-audio.c
> b/drivers/gpu/drm/bridge/synopsys/dw-hdmi-i2s-audio.c index
> 34d8e837555f..b801a28b0f17 100644
> --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi-i2s-audio.c
> +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi-i2s-audio.c
> @@ -102,6 +102,7 @@ static int dw_hdmi_i2s_hw_params(struct device *dev,
> void *data, }
>
> dw_hdmi_set_sample_rate(hdmi, hparms->sample_rate);
> + dw_hdmi_set_channel_status(hdmi, hparms->sample_width);
> dw_hdmi_set_channel_count(hdmi, hparms->channels);
> dw_hdmi_set_channel_allocation(hdmi, hparms-
>cea.channel_allocation);
>
> diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
> b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c index
> bd65d0479683..d1daa369c8ae 100644
> --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
> +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
> @@ -582,6 +582,76 @@ static unsigned int hdmi_compute_n(unsigned int freq,
> unsigned long pixel_clk) return n;
> }
>
> +/*
> + * When transmitting IEC60958 linear PCM audio, these registers allow to
> + * configure the channel status information of all the channel status
> + * bits in the IEC60958 frame. For the moment this configuration is only
> + * used when the I2S audio interface, General Purpose Audio (GPA),
> + * or AHB audio DMA (AHBAUDDMA) interface is active
> + * (for S/PDIF interface this information comes from the stream).
> + */
> +void dw_hdmi_set_channel_status(struct dw_hdmi *hdmi,
> + unsigned int sample_width)
> +{
> + u8 aud_schnl_samplerate;
> + u8 aud_schnl_8;
> + u8 word_length_bits;
> +
> + switch (hdmi->sample_rate) {
> + case 32000:
> + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_32K;
> + break;
> + case 44100:
> + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_44K1;
> + break;
> + case 48000:
> + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_48K;
> + break;
> + case 88200:
> + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_88K2;
> + break;
> + case 96000:
> + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_96K;
> + break;
> + case 176400:
> + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_176K4;
> + break;
> + case 192000:
> + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_192K;
> + break;
> + case 768000:
> + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_768K;
> + break;
> + default:
> + dev_warn(hdmi->dev, "Unsupported audio sample rate (%u)
\n",
> + hdmi->sample_rate);
> + return;
> + }
> +
> + /* set channel status register */
> + hdmi_modb(hdmi, aud_schnl_samplerate,
HDMI_FC_AUDSCHNLS7_SMPRATE_MASK,
> + HDMI_FC_AUDSCHNLS7);
> +
> + /*
> + * Set original frequency to be the same as frequency.
> + * Use one-complement value as stated in IEC60958-3 page 13.
> + */
> + aud_schnl_8 = (~aud_schnl_samplerate) <<
> + HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_OFFSET;
> +
> + /*
> + * Refer to IEC60958-3 page 12. We can accept 16 bits or 24 bits.
> + * Otherwise, set the register to 0t o indicate using default
value.
Nit: "0t 0" -> "0 to"
With that fixed, this patch is:
Reviewed-by: Jernej Skrabec <[email protected]>
Best regards,
Jernej
> + */
> + word_length_bits = (sample_width == 16) ? 0x2 :
> + ((sample_width == 24) ? 0xb : 0);
> +
> + aud_schnl_8 |= word_length_bits <<
HDMI_FC_AUDSCHNLS8_WORDLEGNTH_OFFSET;
> +
> + hdmi_writeb(hdmi, aud_schnl_8, HDMI_FC_AUDSCHNLS8);
> +}
> +EXPORT_SYMBOL_GPL(dw_hdmi_set_channel_status);
> +
> static void hdmi_set_clk_regenerator(struct dw_hdmi *hdmi,
> unsigned long pixel_clk, unsigned int sample_rate)
> {
> diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h
> b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h index
> 6988f12d89d9..619ebc1c8354 100644
> --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h
> +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h
> @@ -158,6 +158,17 @@
> #define HDMI_FC_SPDDEVICEINF 0x1062
> #define HDMI_FC_AUDSCONF 0x1063
> #define HDMI_FC_AUDSSTAT 0x1064
> +#define HDMI_FC_AUDSV 0x1065
> +#define HDMI_FC_AUDSU 0x1066
> +#define HDMI_FC_AUDSCHNLS0 0x1067
> +#define HDMI_FC_AUDSCHNLS1 0x1068
> +#define HDMI_FC_AUDSCHNLS2 0x1069
> +#define HDMI_FC_AUDSCHNLS3 0x106a
> +#define HDMI_FC_AUDSCHNLS4 0x106b
> +#define HDMI_FC_AUDSCHNLS5 0x106c
> +#define HDMI_FC_AUDSCHNLS6 0x106d
> +#define HDMI_FC_AUDSCHNLS7 0x106e
> +#define HDMI_FC_AUDSCHNLS8 0x106f
> #define HDMI_FC_DATACH0FILL 0x1070
> #define HDMI_FC_DATACH1FILL 0x1071
> #define HDMI_FC_DATACH2FILL 0x1072
> @@ -706,6 +717,15 @@ enum {
> /* HDMI_FC_AUDSCHNLS7 field values */
> HDMI_FC_AUDSCHNLS7_ACCURACY_OFFSET = 4,
> HDMI_FC_AUDSCHNLS7_ACCURACY_MASK = 0x30,
> + HDMI_FC_AUDSCHNLS7_SMPRATE_MASK = 0x0f,
> + HDMI_FC_AUDSCHNLS7_SMPRATE_192K = 0xe,
> + HDMI_FC_AUDSCHNLS7_SMPRATE_176K4 = 0xc,
> + HDMI_FC_AUDSCHNLS7_SMPRATE_96K = 0xa,
> + HDMI_FC_AUDSCHNLS7_SMPRATE_768K = 0x9,
> + HDMI_FC_AUDSCHNLS7_SMPRATE_88K2 = 0x8,
> + HDMI_FC_AUDSCHNLS7_SMPRATE_32K = 0x3,
> + HDMI_FC_AUDSCHNLS7_SMPRATE_48K = 0x2,
> + HDMI_FC_AUDSCHNLS7_SMPRATE_44K1 = 0x0,
>
> /* HDMI_FC_AUDSCHNLS8 field values */
> HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_MASK = 0xf0,
> diff --git a/include/drm/bridge/dw_hdmi.h b/include/drm/bridge/dw_hdmi.h
> index cf528c289857..12144d2f80f4 100644
> --- a/include/drm/bridge/dw_hdmi.h
> +++ b/include/drm/bridge/dw_hdmi.h
> @@ -156,6 +156,8 @@ void dw_hdmi_setup_rx_sense(struct dw_hdmi *hdmi, bool
> hpd, bool rx_sense);
>
> void dw_hdmi_set_sample_rate(struct dw_hdmi *hdmi, unsigned int rate);
> void dw_hdmi_set_channel_count(struct dw_hdmi *hdmi, unsigned int cnt);
> +void dw_hdmi_set_channel_status(struct dw_hdmi *hdmi,
> + unsigned int sample_width);
> void dw_hdmi_set_channel_allocation(struct dw_hdmi *hdmi, unsigned int ca);
> void dw_hdmi_audio_enable(struct dw_hdmi *hdmi);
> void dw_hdmi_audio_disable(struct dw_hdmi *hdmi);
On Mon, Sep 9, 2019 at 2:18 AM Jernej Škrabec <[email protected]> wrote:
>
> Dne četrtek, 05. september 2019 ob 11:43:25 CEST je Cheng-Yi Chiang
> napisal(a):
> > From: Yakir Yang <[email protected]>
> >
> > When transmitting IEC60985 linear PCM audio, we configure the
> > Aduio Sample Channel Status information of all the channel
> > status bits in the IEC60958 frame.
> > Refer to 60958-3 page 10 for frequency, original frequency, and
> > wordlength setting.
> >
> > This fix the issue that audio does not come out on some monitors
> > (e.g. LG 22CV241)
> >
> > Note that these registers are only for interfaces:
> > I2S audio interface, General Purpose Audio (GPA), or AHB audio DMA
> > (AHBAUDDMA).
> > For S/PDIF interface this information comes from the stream.
> >
> > Currently this function dw_hdmi_set_channel_status is only called
> > from dw-hdmi-i2s-audio in I2S setup.
> >
> > Signed-off-by: Yakir Yang <[email protected]>
> > Signed-off-by: Cheng-Yi Chiang <[email protected]>
> > ---
> > Original patch by Yakir Yang is at
> >
> > https://lore.kernel.org/patchwork/patch/539653/
> >
> > Change from v1 to v2:
> > 1. Remove the version check because this will only be called by
> > dw-hdmi-i2s-audio, and the registers are available in I2S setup.
> > 2. Set these registers in dw_hdmi_i2s_hw_params.
> > 3. Fix the sample width setting so it can use 16 or 24 bits.
> >
> > .../drm/bridge/synopsys/dw-hdmi-i2s-audio.c | 1 +
> > drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 70 +++++++++++++++++++
> > drivers/gpu/drm/bridge/synopsys/dw-hdmi.h | 20 ++++++
> > include/drm/bridge/dw_hdmi.h | 2 +
> > 4 files changed, 93 insertions(+)
> >
> > diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi-i2s-audio.c
> > b/drivers/gpu/drm/bridge/synopsys/dw-hdmi-i2s-audio.c index
> > 34d8e837555f..b801a28b0f17 100644
> > --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi-i2s-audio.c
> > +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi-i2s-audio.c
> > @@ -102,6 +102,7 @@ static int dw_hdmi_i2s_hw_params(struct device *dev,
> > void *data, }
> >
> > dw_hdmi_set_sample_rate(hdmi, hparms->sample_rate);
> > + dw_hdmi_set_channel_status(hdmi, hparms->sample_width);
> > dw_hdmi_set_channel_count(hdmi, hparms->channels);
> > dw_hdmi_set_channel_allocation(hdmi, hparms-
> >cea.channel_allocation);
> >
> > diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
> > b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c index
> > bd65d0479683..d1daa369c8ae 100644
> > --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
> > +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
> > @@ -582,6 +582,76 @@ static unsigned int hdmi_compute_n(unsigned int freq,
> > unsigned long pixel_clk) return n;
> > }
> >
> > +/*
> > + * When transmitting IEC60958 linear PCM audio, these registers allow to
> > + * configure the channel status information of all the channel status
> > + * bits in the IEC60958 frame. For the moment this configuration is only
> > + * used when the I2S audio interface, General Purpose Audio (GPA),
> > + * or AHB audio DMA (AHBAUDDMA) interface is active
> > + * (for S/PDIF interface this information comes from the stream).
> > + */
> > +void dw_hdmi_set_channel_status(struct dw_hdmi *hdmi,
> > + unsigned int sample_width)
> > +{
> > + u8 aud_schnl_samplerate;
> > + u8 aud_schnl_8;
> > + u8 word_length_bits;
> > +
> > + switch (hdmi->sample_rate) {
> > + case 32000:
> > + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_32K;
> > + break;
> > + case 44100:
> > + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_44K1;
> > + break;
> > + case 48000:
> > + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_48K;
> > + break;
> > + case 88200:
> > + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_88K2;
> > + break;
> > + case 96000:
> > + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_96K;
> > + break;
> > + case 176400:
> > + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_176K4;
> > + break;
> > + case 192000:
> > + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_192K;
> > + break;
> > + case 768000:
> > + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_768K;
> > + break;
> > + default:
> > + dev_warn(hdmi->dev, "Unsupported audio sample rate (%u)
> \n",
> > + hdmi->sample_rate);
> > + return;
> > + }
> > +
> > + /* set channel status register */
> > + hdmi_modb(hdmi, aud_schnl_samplerate,
> HDMI_FC_AUDSCHNLS7_SMPRATE_MASK,
> > + HDMI_FC_AUDSCHNLS7);
> > +
> > + /*
> > + * Set original frequency to be the same as frequency.
> > + * Use one-complement value as stated in IEC60958-3 page 13.
> > + */
> > + aud_schnl_8 = (~aud_schnl_samplerate) <<
> > + HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_OFFSET;
> > +
> > + /*
> > + * Refer to IEC60958-3 page 12. We can accept 16 bits or 24 bits.
> > + * Otherwise, set the register to 0t o indicate using default
> value.
>
> Nit: "0t 0" -> "0 to"
>
> With that fixed, this patch is:
> Reviewed-by: Jernej Skrabec <[email protected]>
>
> Best regards,
> Jernej
Hi Jernej,
Thank you for reviewing the patch.
But as Russell pointed in the next mail,
I will update in v3 to make this patch much more simpler.
>
> > + */
> > + word_length_bits = (sample_width == 16) ? 0x2 :
> > + ((sample_width == 24) ? 0xb : 0);
> > +
> > + aud_schnl_8 |= word_length_bits <<
> HDMI_FC_AUDSCHNLS8_WORDLEGNTH_OFFSET;
> > +
> > + hdmi_writeb(hdmi, aud_schnl_8, HDMI_FC_AUDSCHNLS8);
> > +}
> > +EXPORT_SYMBOL_GPL(dw_hdmi_set_channel_status);
> > +
> > static void hdmi_set_clk_regenerator(struct dw_hdmi *hdmi,
> > unsigned long pixel_clk, unsigned int sample_rate)
> > {
> > diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h
> > b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h index
> > 6988f12d89d9..619ebc1c8354 100644
> > --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h
> > +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h
> > @@ -158,6 +158,17 @@
> > #define HDMI_FC_SPDDEVICEINF 0x1062
> > #define HDMI_FC_AUDSCONF 0x1063
> > #define HDMI_FC_AUDSSTAT 0x1064
> > +#define HDMI_FC_AUDSV 0x1065
> > +#define HDMI_FC_AUDSU 0x1066
> > +#define HDMI_FC_AUDSCHNLS0 0x1067
> > +#define HDMI_FC_AUDSCHNLS1 0x1068
> > +#define HDMI_FC_AUDSCHNLS2 0x1069
> > +#define HDMI_FC_AUDSCHNLS3 0x106a
> > +#define HDMI_FC_AUDSCHNLS4 0x106b
> > +#define HDMI_FC_AUDSCHNLS5 0x106c
> > +#define HDMI_FC_AUDSCHNLS6 0x106d
> > +#define HDMI_FC_AUDSCHNLS7 0x106e
> > +#define HDMI_FC_AUDSCHNLS8 0x106f
> > #define HDMI_FC_DATACH0FILL 0x1070
> > #define HDMI_FC_DATACH1FILL 0x1071
> > #define HDMI_FC_DATACH2FILL 0x1072
> > @@ -706,6 +717,15 @@ enum {
> > /* HDMI_FC_AUDSCHNLS7 field values */
> > HDMI_FC_AUDSCHNLS7_ACCURACY_OFFSET = 4,
> > HDMI_FC_AUDSCHNLS7_ACCURACY_MASK = 0x30,
> > + HDMI_FC_AUDSCHNLS7_SMPRATE_MASK = 0x0f,
> > + HDMI_FC_AUDSCHNLS7_SMPRATE_192K = 0xe,
> > + HDMI_FC_AUDSCHNLS7_SMPRATE_176K4 = 0xc,
> > + HDMI_FC_AUDSCHNLS7_SMPRATE_96K = 0xa,
> > + HDMI_FC_AUDSCHNLS7_SMPRATE_768K = 0x9,
> > + HDMI_FC_AUDSCHNLS7_SMPRATE_88K2 = 0x8,
> > + HDMI_FC_AUDSCHNLS7_SMPRATE_32K = 0x3,
> > + HDMI_FC_AUDSCHNLS7_SMPRATE_48K = 0x2,
> > + HDMI_FC_AUDSCHNLS7_SMPRATE_44K1 = 0x0,
> >
> > /* HDMI_FC_AUDSCHNLS8 field values */
> > HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_MASK = 0xf0,
> > diff --git a/include/drm/bridge/dw_hdmi.h b/include/drm/bridge/dw_hdmi.h
> > index cf528c289857..12144d2f80f4 100644
> > --- a/include/drm/bridge/dw_hdmi.h
> > +++ b/include/drm/bridge/dw_hdmi.h
> > @@ -156,6 +156,8 @@ void dw_hdmi_setup_rx_sense(struct dw_hdmi *hdmi, bool
> > hpd, bool rx_sense);
> >
> > void dw_hdmi_set_sample_rate(struct dw_hdmi *hdmi, unsigned int rate);
> > void dw_hdmi_set_channel_count(struct dw_hdmi *hdmi, unsigned int cnt);
> > +void dw_hdmi_set_channel_status(struct dw_hdmi *hdmi,
> > + unsigned int sample_width);
> > void dw_hdmi_set_channel_allocation(struct dw_hdmi *hdmi, unsigned int ca);
> > void dw_hdmi_audio_enable(struct dw_hdmi *hdmi);
> > void dw_hdmi_audio_disable(struct dw_hdmi *hdmi);
>
>
>
>
On Thu, Sep 05, 2019 at 05:43:25PM +0800, Cheng-Yi Chiang wrote:
> From: Yakir Yang <[email protected]>
>
> When transmitting IEC60985 linear PCM audio, we configure the
> Aduio Sample Channel Status information of all the channel
> status bits in the IEC60958 frame.
> Refer to 60958-3 page 10 for frequency, original frequency, and
> wordlength setting.
>
> This fix the issue that audio does not come out on some monitors
> (e.g. LG 22CV241)
>
> Note that these registers are only for interfaces:
> I2S audio interface, General Purpose Audio (GPA), or AHB audio DMA
> (AHBAUDDMA).
> For S/PDIF interface this information comes from the stream.
>
> Currently this function dw_hdmi_set_channel_status is only called
> from dw-hdmi-i2s-audio in I2S setup.
>
> Signed-off-by: Yakir Yang <[email protected]>
> Signed-off-by: Cheng-Yi Chiang <[email protected]>
> ---
> Original patch by Yakir Yang is at
>
> https://lore.kernel.org/patchwork/patch/539653/
>
> Change from v1 to v2:
> 1. Remove the version check because this will only be called by
> dw-hdmi-i2s-audio, and the registers are available in I2S setup.
> 2. Set these registers in dw_hdmi_i2s_hw_params.
> 3. Fix the sample width setting so it can use 16 or 24 bits.
>
> .../drm/bridge/synopsys/dw-hdmi-i2s-audio.c | 1 +
> drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 70 +++++++++++++++++++
> drivers/gpu/drm/bridge/synopsys/dw-hdmi.h | 20 ++++++
> include/drm/bridge/dw_hdmi.h | 2 +
> 4 files changed, 93 insertions(+)
>
> diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi-i2s-audio.c b/drivers/gpu/drm/bridge/synopsys/dw-hdmi-i2s-audio.c
> index 34d8e837555f..b801a28b0f17 100644
> --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi-i2s-audio.c
> +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi-i2s-audio.c
> @@ -102,6 +102,7 @@ static int dw_hdmi_i2s_hw_params(struct device *dev, void *data,
> }
>
> dw_hdmi_set_sample_rate(hdmi, hparms->sample_rate);
> + dw_hdmi_set_channel_status(hdmi, hparms->sample_width);
> dw_hdmi_set_channel_count(hdmi, hparms->channels);
> dw_hdmi_set_channel_allocation(hdmi, hparms->cea.channel_allocation);
>
dw_hdmi_i2s_hw_params() is passed the channel status data in
hparams->iec.status Rather than re-creating it afresh in the driver,
I'd recommend programming the already supplied channel status data
into the registers.
> diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
> index bd65d0479683..d1daa369c8ae 100644
> --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
> +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
> @@ -582,6 +582,76 @@ static unsigned int hdmi_compute_n(unsigned int freq, unsigned long pixel_clk)
> return n;
> }
>
> +/*
> + * When transmitting IEC60958 linear PCM audio, these registers allow to
> + * configure the channel status information of all the channel status
> + * bits in the IEC60958 frame. For the moment this configuration is only
> + * used when the I2S audio interface, General Purpose Audio (GPA),
> + * or AHB audio DMA (AHBAUDDMA) interface is active
> + * (for S/PDIF interface this information comes from the stream).
> + */
> +void dw_hdmi_set_channel_status(struct dw_hdmi *hdmi,
> + unsigned int sample_width)
> +{
> + u8 aud_schnl_samplerate;
> + u8 aud_schnl_8;
> + u8 word_length_bits;
> +
> + switch (hdmi->sample_rate) {
> + case 32000:
> + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_32K;
> + break;
> + case 44100:
> + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_44K1;
> + break;
> + case 48000:
> + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_48K;
> + break;
> + case 88200:
> + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_88K2;
> + break;
> + case 96000:
> + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_96K;
> + break;
> + case 176400:
> + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_176K4;
> + break;
> + case 192000:
> + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_192K;
> + break;
> + case 768000:
> + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_768K;
> + break;
> + default:
> + dev_warn(hdmi->dev, "Unsupported audio sample rate (%u)\n",
> + hdmi->sample_rate);
> + return;
> + }
> +
> + /* set channel status register */
> + hdmi_modb(hdmi, aud_schnl_samplerate, HDMI_FC_AUDSCHNLS7_SMPRATE_MASK,
> + HDMI_FC_AUDSCHNLS7);
> +
> + /*
> + * Set original frequency to be the same as frequency.
> + * Use one-complement value as stated in IEC60958-3 page 13.
> + */
> + aud_schnl_8 = (~aud_schnl_samplerate) <<
> + HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_OFFSET;
> +
> + /*
> + * Refer to IEC60958-3 page 12. We can accept 16 bits or 24 bits.
> + * Otherwise, set the register to 0t o indicate using default value.
> + */
> + word_length_bits = (sample_width == 16) ? 0x2 :
> + ((sample_width == 24) ? 0xb : 0);
> +
> + aud_schnl_8 |= word_length_bits << HDMI_FC_AUDSCHNLS8_WORDLEGNTH_OFFSET;
> +
> + hdmi_writeb(hdmi, aud_schnl_8, HDMI_FC_AUDSCHNLS8);
> +}
> +EXPORT_SYMBOL_GPL(dw_hdmi_set_channel_status);
As mentioned above, the channel status data is actually already
provided - so we don't really need the above at all. It just
needs the data programmed into the registers.
> +
> static void hdmi_set_clk_regenerator(struct dw_hdmi *hdmi,
> unsigned long pixel_clk, unsigned int sample_rate)
> {
> diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h
> index 6988f12d89d9..619ebc1c8354 100644
> --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h
> +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h
> @@ -158,6 +158,17 @@
> #define HDMI_FC_SPDDEVICEINF 0x1062
> #define HDMI_FC_AUDSCONF 0x1063
> #define HDMI_FC_AUDSSTAT 0x1064
> +#define HDMI_FC_AUDSV 0x1065
> +#define HDMI_FC_AUDSU 0x1066
> +#define HDMI_FC_AUDSCHNLS0 0x1067
> +#define HDMI_FC_AUDSCHNLS1 0x1068
> +#define HDMI_FC_AUDSCHNLS2 0x1069
> +#define HDMI_FC_AUDSCHNLS3 0x106a
> +#define HDMI_FC_AUDSCHNLS4 0x106b
> +#define HDMI_FC_AUDSCHNLS5 0x106c
> +#define HDMI_FC_AUDSCHNLS6 0x106d
> +#define HDMI_FC_AUDSCHNLS7 0x106e
> +#define HDMI_FC_AUDSCHNLS8 0x106f
> #define HDMI_FC_DATACH0FILL 0x1070
> #define HDMI_FC_DATACH1FILL 0x1071
> #define HDMI_FC_DATACH2FILL 0x1072
> @@ -706,6 +717,15 @@ enum {
> /* HDMI_FC_AUDSCHNLS7 field values */
> HDMI_FC_AUDSCHNLS7_ACCURACY_OFFSET = 4,
> HDMI_FC_AUDSCHNLS7_ACCURACY_MASK = 0x30,
> + HDMI_FC_AUDSCHNLS7_SMPRATE_MASK = 0x0f,
> + HDMI_FC_AUDSCHNLS7_SMPRATE_192K = 0xe,
> + HDMI_FC_AUDSCHNLS7_SMPRATE_176K4 = 0xc,
> + HDMI_FC_AUDSCHNLS7_SMPRATE_96K = 0xa,
> + HDMI_FC_AUDSCHNLS7_SMPRATE_768K = 0x9,
> + HDMI_FC_AUDSCHNLS7_SMPRATE_88K2 = 0x8,
> + HDMI_FC_AUDSCHNLS7_SMPRATE_32K = 0x3,
> + HDMI_FC_AUDSCHNLS7_SMPRATE_48K = 0x2,
> + HDMI_FC_AUDSCHNLS7_SMPRATE_44K1 = 0x0,
These look very much like the IEC958_AES* consumer definitions in
include/sound/asoundef.h.
> /* HDMI_FC_AUDSCHNLS8 field values */
> HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_MASK = 0xf0,
> diff --git a/include/drm/bridge/dw_hdmi.h b/include/drm/bridge/dw_hdmi.h
> index cf528c289857..12144d2f80f4 100644
> --- a/include/drm/bridge/dw_hdmi.h
> +++ b/include/drm/bridge/dw_hdmi.h
> @@ -156,6 +156,8 @@ void dw_hdmi_setup_rx_sense(struct dw_hdmi *hdmi, bool hpd, bool rx_sense);
>
> void dw_hdmi_set_sample_rate(struct dw_hdmi *hdmi, unsigned int rate);
> void dw_hdmi_set_channel_count(struct dw_hdmi *hdmi, unsigned int cnt);
> +void dw_hdmi_set_channel_status(struct dw_hdmi *hdmi,
> + unsigned int sample_width);
> void dw_hdmi_set_channel_allocation(struct dw_hdmi *hdmi, unsigned int ca);
> void dw_hdmi_audio_enable(struct dw_hdmi *hdmi);
> void dw_hdmi_audio_disable(struct dw_hdmi *hdmi);
> --
> 2.23.0.187.g17f5b7556c-goog
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> [email protected]
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>
--
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up
According to speedtest.net: 11.9Mbps down 500kbps up
On Mon, Sep 9, 2019 at 2:38 AM Russell King - ARM Linux admin
<[email protected]> wrote:
>
> On Thu, Sep 05, 2019 at 05:43:25PM +0800, Cheng-Yi Chiang wrote:
> > From: Yakir Yang <[email protected]>
> >
> > When transmitting IEC60985 linear PCM audio, we configure the
> > Aduio Sample Channel Status information of all the channel
> > status bits in the IEC60958 frame.
> > Refer to 60958-3 page 10 for frequency, original frequency, and
> > wordlength setting.
> >
> > This fix the issue that audio does not come out on some monitors
> > (e.g. LG 22CV241)
> >
> > Note that these registers are only for interfaces:
> > I2S audio interface, General Purpose Audio (GPA), or AHB audio DMA
> > (AHBAUDDMA).
> > For S/PDIF interface this information comes from the stream.
> >
> > Currently this function dw_hdmi_set_channel_status is only called
> > from dw-hdmi-i2s-audio in I2S setup.
> >
> > Signed-off-by: Yakir Yang <[email protected]>
> > Signed-off-by: Cheng-Yi Chiang <[email protected]>
> > ---
> > Original patch by Yakir Yang is at
> >
> > https://lore.kernel.org/patchwork/patch/539653/
> >
> > Change from v1 to v2:
> > 1. Remove the version check because this will only be called by
> > dw-hdmi-i2s-audio, and the registers are available in I2S setup.
> > 2. Set these registers in dw_hdmi_i2s_hw_params.
> > 3. Fix the sample width setting so it can use 16 or 24 bits.
> >
> > .../drm/bridge/synopsys/dw-hdmi-i2s-audio.c | 1 +
> > drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 70 +++++++++++++++++++
> > drivers/gpu/drm/bridge/synopsys/dw-hdmi.h | 20 ++++++
> > include/drm/bridge/dw_hdmi.h | 2 +
> > 4 files changed, 93 insertions(+)
> >
> > diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi-i2s-audio.c b/drivers/gpu/drm/bridge/synopsys/dw-hdmi-i2s-audio.c
> > index 34d8e837555f..b801a28b0f17 100644
> > --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi-i2s-audio.c
> > +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi-i2s-audio.c
> > @@ -102,6 +102,7 @@ static int dw_hdmi_i2s_hw_params(struct device *dev, void *data,
> > }
> >
> > dw_hdmi_set_sample_rate(hdmi, hparms->sample_rate);
> > + dw_hdmi_set_channel_status(hdmi, hparms->sample_width);
> > dw_hdmi_set_channel_count(hdmi, hparms->channels);
> > dw_hdmi_set_channel_allocation(hdmi, hparms->cea.channel_allocation);
> >
>
> dw_hdmi_i2s_hw_params() is passed the channel status data in
> hparams->iec.status Rather than re-creating it afresh in the driver,
> I'd recommend programming the already supplied channel status data
> into the registers.
>
Hi Russell,
Thank you for pointing this out.
I did not realize that the status data is already set.
I will fix in v3 to make this patch much simpler.
> > diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
> > index bd65d0479683..d1daa369c8ae 100644
> > --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
> > +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
> > @@ -582,6 +582,76 @@ static unsigned int hdmi_compute_n(unsigned int freq, unsigned long pixel_clk)
> > return n;
> > }
> >
> > +/*
> > + * When transmitting IEC60958 linear PCM audio, these registers allow to
> > + * configure the channel status information of all the channel status
> > + * bits in the IEC60958 frame. For the moment this configuration is only
> > + * used when the I2S audio interface, General Purpose Audio (GPA),
> > + * or AHB audio DMA (AHBAUDDMA) interface is active
> > + * (for S/PDIF interface this information comes from the stream).
> > + */
> > +void dw_hdmi_set_channel_status(struct dw_hdmi *hdmi,
> > + unsigned int sample_width)
> > +{
> > + u8 aud_schnl_samplerate;
> > + u8 aud_schnl_8;
> > + u8 word_length_bits;
> > +
> > + switch (hdmi->sample_rate) {
> > + case 32000:
> > + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_32K;
> > + break;
> > + case 44100:
> > + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_44K1;
> > + break;
> > + case 48000:
> > + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_48K;
> > + break;
> > + case 88200:
> > + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_88K2;
> > + break;
> > + case 96000:
> > + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_96K;
> > + break;
> > + case 176400:
> > + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_176K4;
> > + break;
> > + case 192000:
> > + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_192K;
> > + break;
> > + case 768000:
> > + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_768K;
> > + break;
> > + default:
> > + dev_warn(hdmi->dev, "Unsupported audio sample rate (%u)\n",
> > + hdmi->sample_rate);
> > + return;
> > + }
> > +
> > + /* set channel status register */
> > + hdmi_modb(hdmi, aud_schnl_samplerate, HDMI_FC_AUDSCHNLS7_SMPRATE_MASK,
> > + HDMI_FC_AUDSCHNLS7);
> > +
> > + /*
> > + * Set original frequency to be the same as frequency.
> > + * Use one-complement value as stated in IEC60958-3 page 13.
> > + */
> > + aud_schnl_8 = (~aud_schnl_samplerate) <<
> > + HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_OFFSET;
> > +
> > + /*
> > + * Refer to IEC60958-3 page 12. We can accept 16 bits or 24 bits.
> > + * Otherwise, set the register to 0t o indicate using default value.
> > + */
> > + word_length_bits = (sample_width == 16) ? 0x2 :
> > + ((sample_width == 24) ? 0xb : 0);
> > +
> > + aud_schnl_8 |= word_length_bits << HDMI_FC_AUDSCHNLS8_WORDLEGNTH_OFFSET;
> > +
> > + hdmi_writeb(hdmi, aud_schnl_8, HDMI_FC_AUDSCHNLS8);
> > +}
> > +EXPORT_SYMBOL_GPL(dw_hdmi_set_channel_status);
>
> As mentioned above, the channel status data is actually already
> provided - so we don't really need the above at all. It just
> needs the data programmed into the registers.
>
ACK
> > +
> > static void hdmi_set_clk_regenerator(struct dw_hdmi *hdmi,
> > unsigned long pixel_clk, unsigned int sample_rate)
> > {
> > diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h
> > index 6988f12d89d9..619ebc1c8354 100644
> > --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h
> > +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h
> > @@ -158,6 +158,17 @@
> > #define HDMI_FC_SPDDEVICEINF 0x1062
> > #define HDMI_FC_AUDSCONF 0x1063
> > #define HDMI_FC_AUDSSTAT 0x1064
> > +#define HDMI_FC_AUDSV 0x1065
> > +#define HDMI_FC_AUDSU 0x1066
> > +#define HDMI_FC_AUDSCHNLS0 0x1067
> > +#define HDMI_FC_AUDSCHNLS1 0x1068
> > +#define HDMI_FC_AUDSCHNLS2 0x1069
> > +#define HDMI_FC_AUDSCHNLS3 0x106a
> > +#define HDMI_FC_AUDSCHNLS4 0x106b
> > +#define HDMI_FC_AUDSCHNLS5 0x106c
> > +#define HDMI_FC_AUDSCHNLS6 0x106d
> > +#define HDMI_FC_AUDSCHNLS7 0x106e
> > +#define HDMI_FC_AUDSCHNLS8 0x106f
> > #define HDMI_FC_DATACH0FILL 0x1070
> > #define HDMI_FC_DATACH1FILL 0x1071
> > #define HDMI_FC_DATACH2FILL 0x1072
> > @@ -706,6 +717,15 @@ enum {
> > /* HDMI_FC_AUDSCHNLS7 field values */
> > HDMI_FC_AUDSCHNLS7_ACCURACY_OFFSET = 4,
> > HDMI_FC_AUDSCHNLS7_ACCURACY_MASK = 0x30,
> > + HDMI_FC_AUDSCHNLS7_SMPRATE_MASK = 0x0f,
> > + HDMI_FC_AUDSCHNLS7_SMPRATE_192K = 0xe,
> > + HDMI_FC_AUDSCHNLS7_SMPRATE_176K4 = 0xc,
> > + HDMI_FC_AUDSCHNLS7_SMPRATE_96K = 0xa,
> > + HDMI_FC_AUDSCHNLS7_SMPRATE_768K = 0x9,
> > + HDMI_FC_AUDSCHNLS7_SMPRATE_88K2 = 0x8,
> > + HDMI_FC_AUDSCHNLS7_SMPRATE_32K = 0x3,
> > + HDMI_FC_AUDSCHNLS7_SMPRATE_48K = 0x2,
> > + HDMI_FC_AUDSCHNLS7_SMPRATE_44K1 = 0x0,
>
> These look very much like the IEC958_AES* consumer definitions in
> include/sound/asoundef.h.
ACK. Will remove in v3.
>
> > /* HDMI_FC_AUDSCHNLS8 field values */
> > HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_MASK = 0xf0,
> > diff --git a/include/drm/bridge/dw_hdmi.h b/include/drm/bridge/dw_hdmi.h
> > index cf528c289857..12144d2f80f4 100644
> > --- a/include/drm/bridge/dw_hdmi.h
> > +++ b/include/drm/bridge/dw_hdmi.h
> > @@ -156,6 +156,8 @@ void dw_hdmi_setup_rx_sense(struct dw_hdmi *hdmi, bool hpd, bool rx_sense);
> >
> > void dw_hdmi_set_sample_rate(struct dw_hdmi *hdmi, unsigned int rate);
> > void dw_hdmi_set_channel_count(struct dw_hdmi *hdmi, unsigned int cnt);
> > +void dw_hdmi_set_channel_status(struct dw_hdmi *hdmi,
> > + unsigned int sample_width);
> > void dw_hdmi_set_channel_allocation(struct dw_hdmi *hdmi, unsigned int ca);
> > void dw_hdmi_audio_enable(struct dw_hdmi *hdmi);
> > void dw_hdmi_audio_disable(struct dw_hdmi *hdmi);
> > --
> > 2.23.0.187.g17f5b7556c-goog
> >
> >
> > _______________________________________________
> > linux-arm-kernel mailing list
> > [email protected]
> > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
> >
>
> --
> RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
> FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up
> According to speedtest.net: 11.9Mbps down 500kbps up