The code from [1] sets SYS_CTRL_1 to different values depending on the
desired clock phase (0, 1/4, 1/2 or 3/4). A clock phase of 0 aligns the
positive edge of the clock with the pixel data while other values delay
the clock by a fraction of the clock period. A clock phase of 1/2 aligns
the negative edge of the clock with the pixel data.
The driver currently hard codes SYS_CTRL_1 to 0x88 which corresponds to
aligning the positive edge of the clock with the pixel data. This won't
work correctly for panels that require aligning the negative edge of the
clock with the pixel data.
Adjust the clock phase to 0 if DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE is
present in bus_flags, otherwise adjust the clock phase to 1/2 as
appropriate for DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE.
[1] https://github.com/tdjastrzebski/ICN6211-Configurator
Signed-off-by: Jonathan Liu <[email protected]>
---
V2: Use GENMASK and FIELD_PREP macros
---
drivers/gpu/drm/bridge/chipone-icn6211.c | 18 ++++++++++++++++--
1 file changed, 16 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/bridge/chipone-icn6211.c b/drivers/gpu/drm/bridge/chipone-icn6211.c
index 47dea657a752..f1538fb5f8a9 100644
--- a/drivers/gpu/drm/bridge/chipone-icn6211.c
+++ b/drivers/gpu/drm/bridge/chipone-icn6211.c
@@ -9,6 +9,8 @@
#include <drm/drm_print.h>
#include <drm/drm_mipi_dsi.h>
+#include <linux/bitfield.h>
+#include <linux/bits.h>
#include <linux/delay.h>
#include <linux/gpio/consumer.h>
#include <linux/i2c.h>
@@ -26,6 +28,11 @@
#define PD_CTRL(n) (0x0a + ((n) & 0x3)) /* 0..3 */
#define RST_CTRL(n) (0x0e + ((n) & 0x1)) /* 0..1 */
#define SYS_CTRL(n) (0x10 + ((n) & 0x7)) /* 0..4 */
+#define SYS_CTRL_1_CLK_PHASE_MSK GENMASK(5, 4)
+#define CLK_PHASE_0 0
+#define CLK_PHASE_1_4 1
+#define CLK_PHASE_1_2 2
+#define CLK_PHASE_3_4 3
#define RGB_DRV(n) (0x18 + ((n) & 0x3)) /* 0..3 */
#define RGB_DLY(n) (0x1c + ((n) & 0x1)) /* 0..1 */
#define RGB_TEST_CTRL 0x1e
@@ -336,7 +343,7 @@ static void chipone_atomic_enable(struct drm_bridge *bridge,
const struct drm_bridge_state *bridge_state;
u16 hfp, hbp, hsync;
u32 bus_flags;
- u8 pol, id[4];
+ u8 pol, sys_ctrl_1, id[4];
chipone_readb(icn, VENDOR_ID, id);
chipone_readb(icn, DEVICE_ID_H, id + 1);
@@ -414,7 +421,14 @@ static void chipone_atomic_enable(struct drm_bridge *bridge,
chipone_configure_pll(icn, mode);
chipone_writeb(icn, SYS_CTRL(0), 0x40);
- chipone_writeb(icn, SYS_CTRL(1), 0x88);
+ sys_ctrl_1 = 0x88;
+
+ if (bus_flags & DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE)
+ sys_ctrl_1 |= FIELD_PREP(SYS_CTRL_1_CLK_PHASE_MSK, CLK_PHASE_0);
+ else
+ sys_ctrl_1 |= FIELD_PREP(SYS_CTRL_1_CLK_PHASE_MSK, CLK_PHASE_1_2);
+
+ chipone_writeb(icn, SYS_CTRL(1), sys_ctrl_1);
/* icn6211 specific sequence */
chipone_writeb(icn, MIPI_FORCE_0, 0x20);
--
2.36.1
On 5/23/22 15:01, Jonathan Liu wrote:
> The code from [1] sets SYS_CTRL_1 to different values depending on the
> desired clock phase (0, 1/4, 1/2 or 3/4). A clock phase of 0 aligns the
> positive edge of the clock with the pixel data while other values delay
> the clock by a fraction of the clock period. A clock phase of 1/2 aligns
> the negative edge of the clock with the pixel data.
>
> The driver currently hard codes SYS_CTRL_1 to 0x88 which corresponds to
> aligning the positive edge of the clock with the pixel data. This won't
> work correctly for panels that require aligning the negative edge of the
> clock with the pixel data.
>
> Adjust the clock phase to 0 if DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE is
> present in bus_flags, otherwise adjust the clock phase to 1/2 as
> appropriate for DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE.
>
> [1] https://github.com/tdjastrzebski/ICN6211-Configurator
>
> Signed-off-by: Jonathan Liu <[email protected]>
> ---
> V2: Use GENMASK and FIELD_PREP macros
> ---
> drivers/gpu/drm/bridge/chipone-icn6211.c | 18 ++++++++++++++++--
> 1 file changed, 16 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/gpu/drm/bridge/chipone-icn6211.c b/drivers/gpu/drm/bridge/chipone-icn6211.c
> index 47dea657a752..f1538fb5f8a9 100644
> --- a/drivers/gpu/drm/bridge/chipone-icn6211.c
> +++ b/drivers/gpu/drm/bridge/chipone-icn6211.c
> @@ -9,6 +9,8 @@
> #include <drm/drm_print.h>
> #include <drm/drm_mipi_dsi.h>
>
> +#include <linux/bitfield.h>
> +#include <linux/bits.h>
> #include <linux/delay.h>
> #include <linux/gpio/consumer.h>
> #include <linux/i2c.h>
> @@ -26,6 +28,11 @@
> #define PD_CTRL(n) (0x0a + ((n) & 0x3)) /* 0..3 */
> #define RST_CTRL(n) (0x0e + ((n) & 0x1)) /* 0..1 */
> #define SYS_CTRL(n) (0x10 + ((n) & 0x7)) /* 0..4 */
> +#define SYS_CTRL_1_CLK_PHASE_MSK GENMASK(5, 4)
This should be GENMASK(7, 6) , no ?
Hi Marek,
On Mon, 23 May 2022 at 23:15, Marek Vasut <[email protected]> wrote:
>
> On 5/23/22 15:01, Jonathan Liu wrote:
> > The code from [1] sets SYS_CTRL_1 to different values depending on the
> > desired clock phase (0, 1/4, 1/2 or 3/4). A clock phase of 0 aligns the
> > positive edge of the clock with the pixel data while other values delay
> > the clock by a fraction of the clock period. A clock phase of 1/2 aligns
> > the negative edge of the clock with the pixel data.
> >
> > The driver currently hard codes SYS_CTRL_1 to 0x88 which corresponds to
> > aligning the positive edge of the clock with the pixel data. This won't
> > work correctly for panels that require aligning the negative edge of the
> > clock with the pixel data.
> >
> > Adjust the clock phase to 0 if DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE is
> > present in bus_flags, otherwise adjust the clock phase to 1/2 as
> > appropriate for DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE.
> >
> > [1] https://github.com/tdjastrzebski/ICN6211-Configurator
> >
> > Signed-off-by: Jonathan Liu <[email protected]>
> > ---
> > V2: Use GENMASK and FIELD_PREP macros
> > ---
> > drivers/gpu/drm/bridge/chipone-icn6211.c | 18 ++++++++++++++++--
> > 1 file changed, 16 insertions(+), 2 deletions(-)
> >
> > diff --git a/drivers/gpu/drm/bridge/chipone-icn6211.c b/drivers/gpu/drm/bridge/chipone-icn6211.c
> > index 47dea657a752..f1538fb5f8a9 100644
> > --- a/drivers/gpu/drm/bridge/chipone-icn6211.c
> > +++ b/drivers/gpu/drm/bridge/chipone-icn6211.c
> > @@ -9,6 +9,8 @@
> > #include <drm/drm_print.h>
> > #include <drm/drm_mipi_dsi.h>
> >
> > +#include <linux/bitfield.h>
> > +#include <linux/bits.h>
> > #include <linux/delay.h>
> > #include <linux/gpio/consumer.h>
> > #include <linux/i2c.h>
> > @@ -26,6 +28,11 @@
> > #define PD_CTRL(n) (0x0a + ((n) & 0x3)) /* 0..3 */
> > #define RST_CTRL(n) (0x0e + ((n) & 0x1)) /* 0..1 */
> > #define SYS_CTRL(n) (0x10 + ((n) & 0x7)) /* 0..4 */
> > +#define SYS_CTRL_1_CLK_PHASE_MSK GENMASK(5, 4)
>
> This should be GENMASK(7, 6) , no ?
Clock phase 0 = 0b_1000_1000 = 0x88
Clock phase 1/4 = 0b_1001_1000 = 0x98
Clock phase 1/2 = 0b_1010_1000 = 0xA8
Clock phase 3/4 = 0b_1011_1000 = 0xB8
The clock phase bits are 5:4 not 7:6. The upper 2 bits and lower 4
bits are unknown.
Regards,
Jonathan
On 5/23/22 15:20, Jonathan Liu wrote:
> Hi Marek,
>
> On Mon, 23 May 2022 at 23:15, Marek Vasut <[email protected]> wrote:
>>
>> On 5/23/22 15:01, Jonathan Liu wrote:
>>> The code from [1] sets SYS_CTRL_1 to different values depending on the
>>> desired clock phase (0, 1/4, 1/2 or 3/4). A clock phase of 0 aligns the
>>> positive edge of the clock with the pixel data while other values delay
>>> the clock by a fraction of the clock period. A clock phase of 1/2 aligns
>>> the negative edge of the clock with the pixel data.
>>>
>>> The driver currently hard codes SYS_CTRL_1 to 0x88 which corresponds to
>>> aligning the positive edge of the clock with the pixel data. This won't
>>> work correctly for panels that require aligning the negative edge of the
>>> clock with the pixel data.
>>>
>>> Adjust the clock phase to 0 if DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE is
>>> present in bus_flags, otherwise adjust the clock phase to 1/2 as
>>> appropriate for DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE.
>>>
>>> [1] https://github.com/tdjastrzebski/ICN6211-Configurator
>>>
>>> Signed-off-by: Jonathan Liu <[email protected]>
>>> ---
>>> V2: Use GENMASK and FIELD_PREP macros
>>> ---
>>> drivers/gpu/drm/bridge/chipone-icn6211.c | 18 ++++++++++++++++--
>>> 1 file changed, 16 insertions(+), 2 deletions(-)
>>>
>>> diff --git a/drivers/gpu/drm/bridge/chipone-icn6211.c b/drivers/gpu/drm/bridge/chipone-icn6211.c
>>> index 47dea657a752..f1538fb5f8a9 100644
>>> --- a/drivers/gpu/drm/bridge/chipone-icn6211.c
>>> +++ b/drivers/gpu/drm/bridge/chipone-icn6211.c
>>> @@ -9,6 +9,8 @@
>>> #include <drm/drm_print.h>
>>> #include <drm/drm_mipi_dsi.h>
>>>
>>> +#include <linux/bitfield.h>
>>> +#include <linux/bits.h>
>>> #include <linux/delay.h>
>>> #include <linux/gpio/consumer.h>
>>> #include <linux/i2c.h>
>>> @@ -26,6 +28,11 @@
>>> #define PD_CTRL(n) (0x0a + ((n) & 0x3)) /* 0..3 */
>>> #define RST_CTRL(n) (0x0e + ((n) & 0x1)) /* 0..1 */
>>> #define SYS_CTRL(n) (0x10 + ((n) & 0x7)) /* 0..4 */
>>> +#define SYS_CTRL_1_CLK_PHASE_MSK GENMASK(5, 4)
>>
>> This should be GENMASK(7, 6) , no ?
>
> Clock phase 0 = 0b_1000_1000 = 0x88
> Clock phase 1/4 = 0b_1001_1000 = 0x98
> Clock phase 1/2 = 0b_1010_1000 = 0xA8
> Clock phase 3/4 = 0b_1011_1000 = 0xB8
>
> The clock phase bits are 5:4 not 7:6. The upper 2 bits and lower 4
> bits are unknown.
Doh, you're right.
Reviewed-by: Marek Vasut <[email protected]>
On Mon, 23 May 2022 at 15:25, Marek Vasut <[email protected]> wrote:
>
> On 5/23/22 15:20, Jonathan Liu wrote:
> > Hi Marek,
> >
> > On Mon, 23 May 2022 at 23:15, Marek Vasut <[email protected]> wrote:
> >>
> >> On 5/23/22 15:01, Jonathan Liu wrote:
> >>> The code from [1] sets SYS_CTRL_1 to different values depending on the
> >>> desired clock phase (0, 1/4, 1/2 or 3/4). A clock phase of 0 aligns the
> >>> positive edge of the clock with the pixel data while other values delay
> >>> the clock by a fraction of the clock period. A clock phase of 1/2 aligns
> >>> the negative edge of the clock with the pixel data.
> >>>
> >>> The driver currently hard codes SYS_CTRL_1 to 0x88 which corresponds to
> >>> aligning the positive edge of the clock with the pixel data. This won't
> >>> work correctly for panels that require aligning the negative edge of the
> >>> clock with the pixel data.
> >>>
> >>> Adjust the clock phase to 0 if DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE is
> >>> present in bus_flags, otherwise adjust the clock phase to 1/2 as
> >>> appropriate for DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE.
> >>>
> >>> [1] https://github.com/tdjastrzebski/ICN6211-Configurator
> >>>
> >>> Signed-off-by: Jonathan Liu <[email protected]>
> >>> ---
> >>> V2: Use GENMASK and FIELD_PREP macros
> >>> ---
> >>> drivers/gpu/drm/bridge/chipone-icn6211.c | 18 ++++++++++++++++--
> >>> 1 file changed, 16 insertions(+), 2 deletions(-)
> >>>
> >>> diff --git a/drivers/gpu/drm/bridge/chipone-icn6211.c b/drivers/gpu/drm/bridge/chipone-icn6211.c
> >>> index 47dea657a752..f1538fb5f8a9 100644
> >>> --- a/drivers/gpu/drm/bridge/chipone-icn6211.c
> >>> +++ b/drivers/gpu/drm/bridge/chipone-icn6211.c
> >>> @@ -9,6 +9,8 @@
> >>> #include <drm/drm_print.h>
> >>> #include <drm/drm_mipi_dsi.h>
> >>>
> >>> +#include <linux/bitfield.h>
> >>> +#include <linux/bits.h>
> >>> #include <linux/delay.h>
> >>> #include <linux/gpio/consumer.h>
> >>> #include <linux/i2c.h>
> >>> @@ -26,6 +28,11 @@
> >>> #define PD_CTRL(n) (0x0a + ((n) & 0x3)) /* 0..3 */
> >>> #define RST_CTRL(n) (0x0e + ((n) & 0x1)) /* 0..1 */
> >>> #define SYS_CTRL(n) (0x10 + ((n) & 0x7)) /* 0..4 */
> >>> +#define SYS_CTRL_1_CLK_PHASE_MSK GENMASK(5, 4)
> >>
> >> This should be GENMASK(7, 6) , no ?
> >
> > Clock phase 0 = 0b_1000_1000 = 0x88
> > Clock phase 1/4 = 0b_1001_1000 = 0x98
> > Clock phase 1/2 = 0b_1010_1000 = 0xA8
> > Clock phase 3/4 = 0b_1011_1000 = 0xB8
> >
> > The clock phase bits are 5:4 not 7:6. The upper 2 bits and lower 4
> > bits are unknown.
>
> Doh, you're right.
>
> Reviewed-by: Marek Vasut <[email protected]>
Applied to drm-misc-next.