2016-10-27 21:14:00

by Markus Mayer

[permalink] [raw]
Subject: [PATCH v5 0/3] Broadcom STB AVS CPUfreq driver

From: Markus Mayer <[email protected]>

This series contains the CPUfreq driver for Broadcom SoCs that use "AVS
Firmware" for voltage and frequency scaling. All voltage and frequency
transitions are performed by the firmware and are therefore hidden from
Linux.

The driver provides a standard CPUfreq interface to other kernel
components and to userland on the one hand and communicates with the
AVS co-processor on the other.

Communication between the two processors is via shared mailbox
registers and interrupts (ARM -> AVS to tell the firmware that there is
a command to process and AVS -> ARM to tell the driver that a command
finished executing).

Changes from v4:
- Addressed comments regarding the binding document (see also
https://lkml.org/lkml/2016/10/19/642)
- Added Virsh's Acks
- Rebased on v4.9-rc1
- Patches sent from non-Broadcom account on purpose to prevent series
from being marked as spam (this is currently happening for some
recipients)
- No changes to any code

Changes from v3:
- moved code from brcm_avs_cpufreq_exit() into brcm_avs_cpufreq_remove()
- removed brcm_avs_cpufreq_exit() altogether

Changes from v2:
- removed file Documentation/cpu-freq/brcmstb-avs-cpufreq.txt, instead
adding the text as comment in the driver itself
- wildcard match in MAINTAINERS file (drivers/cpufreq/brcmstb*)
- drivers/cpufreq/Kconfig.arm: have ARM_BRCMSTB_AVS_CPUFREQ default y
for ARCH_BRCMSTB
- fixed naming and Kconfig entry for CONFIG_ARM_BRCMSTB_AVS_CPUFREQ_DEBUG
- reordered and fixed include files
- made sure driver name doesn't exceed size of cpufreq_driver.name
- got rid of device_node pointers in struct private_data; there's no
need for them, as we can call of_node_put() in __map_region()
- don't set driver_data for CPUFREQ_TABLE_END
- have brcm_avs_cpufreq_get() read from the firmware rather than return
policy->cur
- don't update policy->cur in brcm_avs_target_index()
- created new function brcm_avs_prepare_init() to handle compatibility
checks during initialization and moved corresponding code from
brcm_avs_cpufreq_init() to the new function
- brcm_avs_prepare_init() is called from brcm_avs_cpufreq_probe() and
therefore will only be called once, even in the case of an error,
whereas brcm_avs_cpufreq_init() is called for every core if there is
an error
- renamed brcm_avs_cpu_(init|exit) to brcm_avs_cpufreq_(init|exit)
- added platform_set_drvdata(pdev, NULL) upon deregistration
- fixed various style complaints by checkpatch.pl --strict
- fixed other style issues
- updated and improved some comments
- added Viresh's Acks to patches 1/3 and 3/3

Changes from v1:
- renamed binding document
- rewrote the introduction of the binding document
- created a new driver documentation file that contains Linux specific
information that was previously part of the binding document
- renamed the driver (and related config options) to include a reference
to "STB", since this implementation is primarily intended for use on
set-top boxes
- improved comments
- updated function __map_region()
- updated struct private_data
- added code to unmap memory regions in the error and exit paths
- added new sysfs property to report frequency directly from the
co-processor register

Markus Mayer (3):
dt: cpufreq: brcm: New binding document for brcmstb-avs-cpufreq
cpufreq: brcmstb-avs-cpufreq: AVS CPUfreq driver for Broadcom STB SoCs
cpufreq: brcmstb-avs-cpufreq: add debugfs support

.../bindings/cpufreq/brcm,stb-avs-cpu-freq.txt | 78 ++
MAINTAINERS | 8 +
drivers/cpufreq/Kconfig.arm | 21 +
drivers/cpufreq/Makefile | 1 +
drivers/cpufreq/brcmstb-avs-cpufreq.c | 1057 ++++++++++++++++++++
5 files changed, 1165 insertions(+)
create mode 100644 Documentation/devicetree/bindings/cpufreq/brcm,stb-avs-cpu-freq.txt
create mode 100644 drivers/cpufreq/brcmstb-avs-cpufreq.c

--
2.7.4


2016-10-27 21:11:31

by Markus Mayer

[permalink] [raw]
Subject: [PATCH v5 3/3] cpufreq: brcmstb-avs-cpufreq: add debugfs support

From: Markus Mayer <[email protected]>

In order to aid debugging, we add a debugfs interface to the driver
that allows direct interaction with the AVS co-processor.

The debugfs interface provides a means for reading all and writing some
of the mailbox registers directly from the shell prompt and enables a
user to execute the communications protocol between ARM CPU and AVS CPU
step-by-step.

This interface should be used for debugging purposes only.

Signed-off-by: Markus Mayer <[email protected]>
Acked-by: Viresh Kumar <[email protected]>
---
drivers/cpufreq/Kconfig.arm | 10 ++
drivers/cpufreq/brcmstb-avs-cpufreq.c | 323 +++++++++++++++++++++++++++++++++-
2 files changed, 332 insertions(+), 1 deletion(-)

diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm
index d4e3795..43f261e 100644
--- a/drivers/cpufreq/Kconfig.arm
+++ b/drivers/cpufreq/Kconfig.arm
@@ -23,6 +23,16 @@ config ARM_BRCMSTB_AVS_CPUFREQ

Say Y, if you have a Broadcom SoC with AVS support for DFS or DVFS.

+config ARM_BRCMSTB_AVS_CPUFREQ_DEBUG
+ bool "Broadcom STB AVS CPUfreq driver sysfs debug capability"
+ depends on ARM_BRCMSTB_AVS_CPUFREQ
+ help
+ Enabling this option turns on debug support via sysfs under
+ /sys/kernel/debug/brcmstb-avs-cpufreq. It is possible to read all and
+ write some AVS mailbox registers through sysfs entries.
+
+ If in doubt, say N.
+
config ARM_DT_BL_CPUFREQ
tristate "Generic probing via DT for ARM big LITTLE CPUfreq driver"
depends on ARM_BIG_LITTLE_CPUFREQ && OF
diff --git a/drivers/cpufreq/brcmstb-avs-cpufreq.c b/drivers/cpufreq/brcmstb-avs-cpufreq.c
index 4415fa0..b761d54 100644
--- a/drivers/cpufreq/brcmstb-avs-cpufreq.c
+++ b/drivers/cpufreq/brcmstb-avs-cpufreq.c
@@ -49,6 +49,13 @@
#include <linux/platform_device.h>
#include <linux/semaphore.h>

+#ifdef CONFIG_ARM_BRCMSTB_AVS_CPUFREQ_DEBUG
+#include <linux/ctype.h>
+#include <linux/debugfs.h>
+#include <linux/slab.h>
+#include <linux/uaccess.h>
+#endif
+
/* Max number of arguments AVS calls take */
#define AVS_MAX_CMD_ARGS 4
/*
@@ -175,11 +182,88 @@ struct private_data {
void __iomem *base;
void __iomem *avs_intr_base;
struct device *dev;
+#ifdef CONFIG_ARM_BRCMSTB_AVS_CPUFREQ_DEBUG
+ struct dentry *debugfs;
+#endif
struct completion done;
struct semaphore sem;
struct pmap pmap;
};

+#ifdef CONFIG_ARM_BRCMSTB_AVS_CPUFREQ_DEBUG
+
+enum debugfs_format {
+ DEBUGFS_NORMAL,
+ DEBUGFS_FLOAT,
+ DEBUGFS_REV,
+};
+
+struct debugfs_data {
+ struct debugfs_entry *entry;
+ struct private_data *priv;
+};
+
+struct debugfs_entry {
+ char *name;
+ u32 offset;
+ fmode_t mode;
+ enum debugfs_format format;
+};
+
+#define DEBUGFS_ENTRY(name, mode, format) { \
+ #name, AVS_MBOX_##name, mode, format \
+}
+
+/*
+ * These are used for debugfs only. Otherwise we use AVS_MBOX_PARAM() directly.
+ */
+#define AVS_MBOX_PARAM1 AVS_MBOX_PARAM(0)
+#define AVS_MBOX_PARAM2 AVS_MBOX_PARAM(1)
+#define AVS_MBOX_PARAM3 AVS_MBOX_PARAM(2)
+#define AVS_MBOX_PARAM4 AVS_MBOX_PARAM(3)
+
+/*
+ * This table stores the name, access permissions and offset for each hardware
+ * register and is used to generate debugfs entries.
+ */
+static struct debugfs_entry debugfs_entries[] = {
+ DEBUGFS_ENTRY(COMMAND, S_IWUSR, DEBUGFS_NORMAL),
+ DEBUGFS_ENTRY(STATUS, S_IWUSR, DEBUGFS_NORMAL),
+ DEBUGFS_ENTRY(VOLTAGE0, 0, DEBUGFS_FLOAT),
+ DEBUGFS_ENTRY(TEMP0, 0, DEBUGFS_FLOAT),
+ DEBUGFS_ENTRY(PV0, 0, DEBUGFS_FLOAT),
+ DEBUGFS_ENTRY(MV0, 0, DEBUGFS_FLOAT),
+ DEBUGFS_ENTRY(PARAM1, S_IWUSR, DEBUGFS_NORMAL),
+ DEBUGFS_ENTRY(PARAM2, S_IWUSR, DEBUGFS_NORMAL),
+ DEBUGFS_ENTRY(PARAM3, S_IWUSR, DEBUGFS_NORMAL),
+ DEBUGFS_ENTRY(PARAM4, S_IWUSR, DEBUGFS_NORMAL),
+ DEBUGFS_ENTRY(REVISION, 0, DEBUGFS_REV),
+ DEBUGFS_ENTRY(PSTATE, 0, DEBUGFS_NORMAL),
+ DEBUGFS_ENTRY(HEARTBEAT, 0, DEBUGFS_NORMAL),
+ DEBUGFS_ENTRY(MAGIC, S_IWUSR, DEBUGFS_NORMAL),
+ DEBUGFS_ENTRY(SIGMA_HVT, 0, DEBUGFS_NORMAL),
+ DEBUGFS_ENTRY(SIGMA_SVT, 0, DEBUGFS_NORMAL),
+ DEBUGFS_ENTRY(VOLTAGE1, 0, DEBUGFS_FLOAT),
+ DEBUGFS_ENTRY(TEMP1, 0, DEBUGFS_FLOAT),
+ DEBUGFS_ENTRY(PV1, 0, DEBUGFS_FLOAT),
+ DEBUGFS_ENTRY(MV1, 0, DEBUGFS_FLOAT),
+ DEBUGFS_ENTRY(FREQUENCY, 0, DEBUGFS_NORMAL),
+};
+
+static int brcm_avs_target_index(struct cpufreq_policy *, unsigned int);
+
+static char *__strtolower(char *s)
+{
+ char *p;
+
+ for (p = s; *p; p++)
+ *p = tolower(*p);
+
+ return s;
+}
+
+#endif /* CONFIG_ARM_BRCMSTB_AVS_CPUFREQ_DEBUG */
+
static void __iomem *__map_region(const char *name)
{
struct device_node *np;
@@ -432,6 +516,238 @@ brcm_avs_get_freq_table(struct device *dev, struct private_data *priv)
return table;
}

+#ifdef CONFIG_ARM_BRCMSTB_AVS_CPUFREQ_DEBUG
+
+#define MANT(x) (unsigned int)(abs((x)) / 1000)
+#define FRAC(x) (unsigned int)(abs((x)) - abs((x)) / 1000 * 1000)
+
+static int brcm_avs_debug_show(struct seq_file *s, void *data)
+{
+ struct debugfs_data *dbgfs = s->private;
+ void __iomem *base;
+ u32 val, offset;
+
+ if (!dbgfs) {
+ seq_puts(s, "No device pointer\n");
+ return 0;
+ }
+
+ base = dbgfs->priv->base;
+ offset = dbgfs->entry->offset;
+ val = readl(base + offset);
+ switch (dbgfs->entry->format) {
+ case DEBUGFS_NORMAL:
+ seq_printf(s, "%u\n", val);
+ break;
+ case DEBUGFS_FLOAT:
+ seq_printf(s, "%d.%03d\n", MANT(val), FRAC(val));
+ break;
+ case DEBUGFS_REV:
+ seq_printf(s, "%c.%c.%c.%c\n", (val >> 24 & 0xff),
+ (val >> 16 & 0xff), (val >> 8 & 0xff),
+ val & 0xff);
+ break;
+ }
+ seq_printf(s, "0x%08x\n", val);
+
+ return 0;
+}
+
+#undef MANT
+#undef FRAC
+
+static ssize_t brcm_avs_seq_write(struct file *file, const char __user *buf,
+ size_t size, loff_t *ppos)
+{
+ struct seq_file *s = file->private_data;
+ struct debugfs_data *dbgfs = s->private;
+ struct private_data *priv = dbgfs->priv;
+ void __iomem *base, *avs_intr_base;
+ bool use_issue_command = false;
+ unsigned long val, offset;
+ char str[128];
+ int ret;
+ char *str_ptr = str;
+
+ if (size >= sizeof(str))
+ return -E2BIG;
+
+ memset(str, 0, sizeof(str));
+ ret = copy_from_user(str, buf, size);
+ if (ret)
+ return ret;
+
+ base = priv->base;
+ avs_intr_base = priv->avs_intr_base;
+ offset = dbgfs->entry->offset;
+ /*
+ * Special case writing to "command" entry only: if the string starts
+ * with a 'c', we use the driver's __issue_avs_command() function.
+ * Otherwise, we perform a raw write. This should allow testing of raw
+ * access as well as using the higher level function. (Raw access
+ * doesn't clear the firmware return status after issuing the command.)
+ */
+ if (str_ptr[0] == 'c' && offset == AVS_MBOX_COMMAND) {
+ use_issue_command = true;
+ str_ptr++;
+ }
+ if (kstrtoul(str_ptr, 0, &val) != 0)
+ return -EINVAL;
+
+ /*
+ * Setting the P-state is a special case. We need to update the CPU
+ * frequency we report.
+ */
+ if (val == AVS_CMD_SET_PSTATE) {
+ struct cpufreq_policy *policy;
+ unsigned int pstate;
+
+ policy = cpufreq_cpu_get(smp_processor_id());
+ /* Read back the P-state we are about to set */
+ pstate = readl(base + AVS_MBOX_PARAM(0));
+ if (use_issue_command) {
+ ret = brcm_avs_target_index(policy, pstate);
+ return ret ? ret : size;
+ }
+ policy->cur = policy->freq_table[pstate].frequency;
+ }
+
+ if (use_issue_command) {
+ ret = __issue_avs_command(priv, val, false, NULL);
+ } else {
+ /* Locking here is not perfect, but is only for debug. */
+ ret = down_interruptible(&priv->sem);
+ if (ret)
+ return ret;
+
+ writel(val, base + offset);
+ /* We have to wake up the firmware to process a command. */
+ if (offset == AVS_MBOX_COMMAND)
+ writel(AVS_CPU_L2_INT_MASK,
+ avs_intr_base + AVS_CPU_L2_SET0);
+ up(&priv->sem);
+ }
+
+ return ret ? ret : size;
+}
+
+static struct debugfs_entry *__find_debugfs_entry(const char *name)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(debugfs_entries); i++)
+ if (strcasecmp(debugfs_entries[i].name, name) == 0)
+ return &debugfs_entries[i];
+
+ return NULL;
+}
+
+static int brcm_avs_debug_open(struct inode *inode, struct file *file)
+{
+ struct debugfs_data *data;
+ fmode_t fmode;
+ int ret;
+
+ /*
+ * seq_open(), which is called by single_open(), clears "write" access.
+ * We need write access to some files, so we preserve our access mode
+ * and restore it.
+ */
+ fmode = file->f_mode;
+ /*
+ * Check access permissions even for root. We don't want to be writing
+ * to read-only registers. Access for regular users has already been
+ * checked by the VFS layer.
+ */
+ if ((fmode & FMODE_WRITER) && !(inode->i_mode & S_IWUSR))
+ return -EACCES;
+
+ data = kmalloc(sizeof(*data), GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+ /*
+ * We use the same file system operations for all our debug files. To
+ * produce specific output, we look up the file name upon opening a
+ * debugfs entry and map it to a memory offset. This offset is then used
+ * in the generic "show" function to read a specific register.
+ */
+ data->entry = __find_debugfs_entry(file->f_path.dentry->d_iname);
+ data->priv = inode->i_private;
+
+ ret = single_open(file, brcm_avs_debug_show, data);
+ if (ret)
+ kfree(data);
+ file->f_mode = fmode;
+
+ return ret;
+}
+
+static int brcm_avs_debug_release(struct inode *inode, struct file *file)
+{
+ struct seq_file *seq_priv = file->private_data;
+ struct debugfs_data *data = seq_priv->private;
+
+ kfree(data);
+ return single_release(inode, file);
+}
+
+static const struct file_operations brcm_avs_debug_ops = {
+ .open = brcm_avs_debug_open,
+ .read = seq_read,
+ .write = brcm_avs_seq_write,
+ .llseek = seq_lseek,
+ .release = brcm_avs_debug_release,
+};
+
+static void brcm_avs_cpufreq_debug_init(struct platform_device *pdev)
+{
+ struct private_data *priv = platform_get_drvdata(pdev);
+ struct dentry *dir;
+ int i;
+
+ if (!priv)
+ return;
+
+ dir = debugfs_create_dir(BRCM_AVS_CPUFREQ_NAME, NULL);
+ if (IS_ERR_OR_NULL(dir))
+ return;
+ priv->debugfs = dir;
+
+ for (i = 0; i < ARRAY_SIZE(debugfs_entries); i++) {
+ /*
+ * The DEBUGFS_ENTRY macro generates uppercase strings. We
+ * convert them to lowercase before creating the debugfs
+ * entries.
+ */
+ char *entry = __strtolower(debugfs_entries[i].name);
+ fmode_t mode = debugfs_entries[i].mode;
+
+ if (!debugfs_create_file(entry, S_IFREG | S_IRUGO | mode,
+ dir, priv, &brcm_avs_debug_ops)) {
+ priv->debugfs = NULL;
+ debugfs_remove_recursive(dir);
+ break;
+ }
+ }
+}
+
+static void brcm_avs_cpufreq_debug_exit(struct platform_device *pdev)
+{
+ struct private_data *priv = platform_get_drvdata(pdev);
+
+ if (priv && priv->debugfs) {
+ debugfs_remove_recursive(priv->debugfs);
+ priv->debugfs = NULL;
+ }
+}
+
+#else
+
+static void brcm_avs_cpufreq_debug_init(struct platform_device *pdev) {}
+static void brcm_avs_cpufreq_debug_exit(struct platform_device *pdev) {}
+
+#endif /* CONFIG_ARM_BRCMSTB_AVS_CPUFREQ_DEBUG */
+
/*
* To ensure the right firmware is running we need to
* - check the MAGIC matches what we expect
@@ -694,8 +1010,11 @@ static int brcm_avs_cpufreq_probe(struct platform_device *pdev)
return ret;

brcm_avs_driver.driver_data = pdev;
+ ret = cpufreq_register_driver(&brcm_avs_driver);
+ if (!ret)
+ brcm_avs_cpufreq_debug_init(pdev);

- return cpufreq_register_driver(&brcm_avs_driver);
+ return ret;
}

static int brcm_avs_cpufreq_remove(struct platform_device *pdev)
@@ -707,6 +1026,8 @@ static int brcm_avs_cpufreq_remove(struct platform_device *pdev)
if (ret)
return ret;

+ brcm_avs_cpufreq_debug_exit(pdev);
+
priv = platform_get_drvdata(pdev);
iounmap(priv->base);
iounmap(priv->avs_intr_base);
--
2.7.4

2016-10-27 21:14:27

by Markus Mayer

[permalink] [raw]
Subject: [PATCH v5 1/3] dt: cpufreq: brcm: New binding document for brcmstb-avs-cpufreq

From: Markus Mayer <[email protected]>

Add the binding document for the new brcmstb-avs-cpufreq driver.

Signed-off-by: Markus Mayer <[email protected]>
Acked-by: Viresh Kumar <[email protected]>
---
.../bindings/cpufreq/brcm,stb-avs-cpu-freq.txt | 78 ++++++++++++++++++++++
MAINTAINERS | 7 ++
2 files changed, 85 insertions(+)
create mode 100644 Documentation/devicetree/bindings/cpufreq/brcm,stb-avs-cpu-freq.txt

diff --git a/Documentation/devicetree/bindings/cpufreq/brcm,stb-avs-cpu-freq.txt b/Documentation/devicetree/bindings/cpufreq/brcm,stb-avs-cpu-freq.txt
new file mode 100644
index 0000000..af23857
--- /dev/null
+++ b/Documentation/devicetree/bindings/cpufreq/brcm,stb-avs-cpu-freq.txt
@@ -0,0 +1,78 @@
+Broadcom AVS mail box and interrupt register bindings
+=====================================================
+
+A total of three DT nodes are required. One node (brcm,avs-cpu-data-mem)
+references the mailbox register used to communicate with the AVS CPU[1]. The
+second node (brcm,avs-cpu-l2-intr) is required to trigger an interrupt on
+the AVS CPU. The interrupt tells the AVS CPU that it needs to process a
+command sent to it by a driver. Interrupting the AVS CPU is mandatory for
+commands to be processed.
+
+The interface also requires a reference to the AVS host interrupt controller,
+so a driver can react to interrupts generated by the AVS CPU whenever a command
+has been processed. See [2] for more information on the brcm,l2-intc node.
+
+[1] The AVS CPU is an independent co-processor that runs proprietary
+firmware. On some SoCs, this firmware supports DFS and DVFS in addition to
+Adaptive Voltage Scaling.
+
+[2] Documentation/devicetree/bindings/interrupt-controller/brcm,l2-intc.txt
+
+
+Node brcm,avs-cpu-data-mem
+--------------------------
+
+Required properties:
+- compatible: must include: brcm,avs-cpu-data-mem and
+ should include: one of brcm,bcm7271-avs-cpu-data-mem or
+ brcm,bcm7268-avs-cpu-data-mem
+- reg: Specifies base physical address and size of the registers.
+- interrupts: The interrupt that the AVS CPU will use to interrupt the host
+ when a command completed.
+- interrupt-parent: The interrupt controller the above interrupt is routed
+ through.
+- interrupt-names: The name of the interrupt used to interrupt the host.
+
+Optional properties:
+- None
+
+Node brcm,avs-cpu-l2-intr
+-------------------------
+
+Required properties:
+- compatible: must include: brcm,avs-cpu-l2-intr and
+ should include: one of brcm,bcm7271-avs-cpu-l2-intr or
+ brcm,bcm7268-avs-cpu-l2-intr
+- reg: Specifies base physical address and size of the registers.
+
+Optional properties:
+- None
+
+
+Example
+=======
+
+ avs_host_l2_intc: interrupt-controller@f04d1200 {
+ #interrupt-cells = <1>;
+ compatible = "brcm,l2-intc";
+ interrupt-parent = <&intc>;
+ reg = <0xf04d1200 0x48>;
+ interrupt-controller;
+ interrupts = <0x0 0x19 0x0>;
+ interrupt-names = "avs";
+ };
+
+ avs-cpu-data-mem@f04c4000 {
+ compatible = "brcm,bcm7271-avs-cpu-data-mem",
+ "brcm,avs-cpu-data-mem";
+ reg = <0xf04c4000 0x60>;
+ interrupts = <0x1a>;
+ interrupt-parent = <&avs_host_l2_intc>;
+ interrupt-names = "sw_intr";
+ };
+
+ avs-cpu-l2-intr@f04d1100 {
+ compatible = "brcm,bcm7271-avs-cpu-l2-intr",
+ "brcm,avs-cpu-l2-intr";
+ reg = <0xf04d1100 0x10>;
+ };
diff --git a/MAINTAINERS b/MAINTAINERS
index 1cd38a7..9379aca 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2738,6 +2738,13 @@ L: [email protected]
S: Maintained
F: drivers/mtd/nand/brcmnand/

+BROADCOM STB AVS CPUFREQ DRIVER
+M: Markus Mayer <[email protected]>
+M: [email protected]
+L: [email protected]
+S: Maintained
+F: Documentation/devicetree/bindings/cpufreq/brcm,stb-avs-cpu-freq.txt
+
BROADCOM SPECIFIC AMBA DRIVER (BCMA)
M: Rafał Miłecki <[email protected]>
L: [email protected]
--
2.7.4

2016-10-27 21:14:40

by Markus Mayer

[permalink] [raw]
Subject: [PATCH v5 2/3] cpufreq: brcmstb-avs-cpufreq: AVS CPUfreq driver for Broadcom STB SoCs

From: Markus Mayer <[email protected]>

This driver supports voltage and frequency scaling on Broadcom STB SoCs
using AVS firmware with DFS and DVFS support.

Actual frequency or voltage scaling is done exclusively by the AVS
firmware. The driver merely provides a standard CPUfreq interface to
other kernel components and userland, and instructs the AVS firmware to
perform frequency or voltage changes on its behalf.

Signed-off-by: Markus Mayer <[email protected]>
Acked-by: Viresh Kumar <[email protected]>
---
MAINTAINERS | 1 +
drivers/cpufreq/Kconfig.arm | 11 +
drivers/cpufreq/Makefile | 1 +
drivers/cpufreq/brcmstb-avs-cpufreq.c | 736 ++++++++++++++++++++++++++++++++++
4 files changed, 749 insertions(+)
create mode 100644 drivers/cpufreq/brcmstb-avs-cpufreq.c

diff --git a/MAINTAINERS b/MAINTAINERS
index 9379aca..d0ca119 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2744,6 +2744,7 @@ M: [email protected]
L: [email protected]
S: Maintained
F: Documentation/devicetree/bindings/cpufreq/brcm,stb-avs-cpu-freq.txt
+F: drivers/cpufreq/brcmstb*

BROADCOM SPECIFIC AMBA DRIVER (BCMA)
M: Rafał Miłecki <[email protected]>
diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm
index d89b8af..d4e3795 100644
--- a/drivers/cpufreq/Kconfig.arm
+++ b/drivers/cpufreq/Kconfig.arm
@@ -12,6 +12,17 @@ config ARM_BIG_LITTLE_CPUFREQ
help
This enables the Generic CPUfreq driver for ARM big.LITTLE platforms.

+config ARM_BRCMSTB_AVS_CPUFREQ
+ tristate "Broadcom STB AVS CPUfreq driver"
+ depends on ARCH_BRCMSTB || COMPILE_TEST
+ default y
+ help
+ Some Broadcom STB SoCs use a co-processor running proprietary firmware
+ ("AVS") to handle voltage and frequency scaling. This driver provides
+ a standard CPUfreq interface to to the firmware.
+
+ Say Y, if you have a Broadcom SoC with AVS support for DFS or DVFS.
+
config ARM_DT_BL_CPUFREQ
tristate "Generic probing via DT for ARM big LITTLE CPUfreq driver"
depends on ARM_BIG_LITTLE_CPUFREQ && OF
diff --git a/drivers/cpufreq/Makefile b/drivers/cpufreq/Makefile
index 0a9b6a09..ac54f64 100644
--- a/drivers/cpufreq/Makefile
+++ b/drivers/cpufreq/Makefile
@@ -51,6 +51,7 @@ obj-$(CONFIG_ARM_BIG_LITTLE_CPUFREQ) += arm_big_little.o
# LITTLE drivers, so that it is probed last.
obj-$(CONFIG_ARM_DT_BL_CPUFREQ) += arm_big_little_dt.o

+obj-$(CONFIG_ARM_BRCMSTB_AVS_CPUFREQ) += brcmstb-avs-cpufreq.o
obj-$(CONFIG_ARCH_DAVINCI) += davinci-cpufreq.o
obj-$(CONFIG_UX500_SOC_DB8500) += dbx500-cpufreq.o
obj-$(CONFIG_ARM_EXYNOS5440_CPUFREQ) += exynos5440-cpufreq.o
diff --git a/drivers/cpufreq/brcmstb-avs-cpufreq.c b/drivers/cpufreq/brcmstb-avs-cpufreq.c
new file mode 100644
index 0000000..4415fa0
--- /dev/null
+++ b/drivers/cpufreq/brcmstb-avs-cpufreq.c
@@ -0,0 +1,736 @@
+/*
+ * CPU frequency scaling for Broadcom SoCs with AVS firmware that
+ * supports DVS or DVFS
+ *
+ * Copyright (c) 2016 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+/*
+ * "AVS" is the name of a firmware developed at Broadcom. It derives
+ * its name from the technique called "Adaptive Voltage Scaling".
+ * Adaptive voltage scaling was the original purpose of this firmware.
+ * The AVS firmware still supports "AVS mode", where all it does is
+ * adaptive voltage scaling. However, on some newer Broadcom SoCs, the
+ * AVS Firmware, despite its unchanged name, also supports DFS mode and
+ * DVFS mode.
+ *
+ * In the context of this document and the related driver, "AVS" by
+ * itself always means the Broadcom firmware and never refers to the
+ * technique called "Adaptive Voltage Scaling".
+ *
+ * The Broadcom STB AVS CPUfreq driver provides voltage and frequency
+ * scaling on Broadcom SoCs using AVS firmware with support for DFS and
+ * DVFS. The AVS firmware is running on its own co-processor. The
+ * driver supports both uniprocessor (UP) and symmetric multiprocessor
+ * (SMP) systems which share clock and voltage across all CPUs.
+ *
+ * Actual voltage and frequency scaling is done solely by the AVS
+ * firmware. This driver does not change frequency or voltage itself.
+ * It provides a standard CPUfreq interface to the rest of the kernel
+ * and to userland. It interfaces with the AVS firmware to effect the
+ * requested changes and to report back the current system status in a
+ * way that is expected by existing tools.
+ */
+
+#include <linux/cpufreq.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+#include <linux/semaphore.h>
+
+/* Max number of arguments AVS calls take */
+#define AVS_MAX_CMD_ARGS 4
+/*
+ * This macro is used to generate AVS parameter register offsets. For
+ * x >= AVS_MAX_CMD_ARGS, it returns 0 to protect against accidental memory
+ * access outside of the parameter range. (Offset 0 is the first parameter.)
+ */
+#define AVS_PARAM_MULT(x) ((x) < AVS_MAX_CMD_ARGS ? (x) : 0)
+
+/* AVS Mailbox Register offsets */
+#define AVS_MBOX_COMMAND 0x00
+#define AVS_MBOX_STATUS 0x04
+#define AVS_MBOX_VOLTAGE0 0x08
+#define AVS_MBOX_TEMP0 0x0c
+#define AVS_MBOX_PV0 0x10
+#define AVS_MBOX_MV0 0x14
+#define AVS_MBOX_PARAM(x) (0x18 + AVS_PARAM_MULT(x) * sizeof(u32))
+#define AVS_MBOX_REVISION 0x28
+#define AVS_MBOX_PSTATE 0x2c
+#define AVS_MBOX_HEARTBEAT 0x30
+#define AVS_MBOX_MAGIC 0x34
+#define AVS_MBOX_SIGMA_HVT 0x38
+#define AVS_MBOX_SIGMA_SVT 0x3c
+#define AVS_MBOX_VOLTAGE1 0x40
+#define AVS_MBOX_TEMP1 0x44
+#define AVS_MBOX_PV1 0x48
+#define AVS_MBOX_MV1 0x4c
+#define AVS_MBOX_FREQUENCY 0x50
+
+/* AVS Commands */
+#define AVS_CMD_AVAILABLE 0x00
+#define AVS_CMD_DISABLE 0x10
+#define AVS_CMD_ENABLE 0x11
+#define AVS_CMD_S2_ENTER 0x12
+#define AVS_CMD_S2_EXIT 0x13
+#define AVS_CMD_BBM_ENTER 0x14
+#define AVS_CMD_BBM_EXIT 0x15
+#define AVS_CMD_S3_ENTER 0x16
+#define AVS_CMD_S3_EXIT 0x17
+#define AVS_CMD_BALANCE 0x18
+/* PMAP and P-STATE commands */
+#define AVS_CMD_GET_PMAP 0x30
+#define AVS_CMD_SET_PMAP 0x31
+#define AVS_CMD_GET_PSTATE 0x40
+#define AVS_CMD_SET_PSTATE 0x41
+
+/* Different modes AVS supports (for GET_PMAP/SET_PMAP) */
+#define AVS_MODE_AVS 0x0
+#define AVS_MODE_DFS 0x1
+#define AVS_MODE_DVS 0x2
+#define AVS_MODE_DVFS 0x3
+
+/*
+ * PMAP parameter p1
+ * unused:31-24, mdiv_p0:23-16, unused:15-14, pdiv:13-10 , ndiv_int:9-0
+ */
+#define NDIV_INT_SHIFT 0
+#define NDIV_INT_MASK 0x3ff
+#define PDIV_SHIFT 10
+#define PDIV_MASK 0xf
+#define MDIV_P0_SHIFT 16
+#define MDIV_P0_MASK 0xff
+/*
+ * PMAP parameter p2
+ * mdiv_p4:31-24, mdiv_p3:23-16, mdiv_p2:15:8, mdiv_p1:7:0
+ */
+#define MDIV_P1_SHIFT 0
+#define MDIV_P1_MASK 0xff
+#define MDIV_P2_SHIFT 8
+#define MDIV_P2_MASK 0xff
+#define MDIV_P3_SHIFT 16
+#define MDIV_P3_MASK 0xff
+#define MDIV_P4_SHIFT 24
+#define MDIV_P4_MASK 0xff
+
+/* Different P-STATES AVS supports (for GET_PSTATE/SET_PSTATE) */
+#define AVS_PSTATE_P0 0x0
+#define AVS_PSTATE_P1 0x1
+#define AVS_PSTATE_P2 0x2
+#define AVS_PSTATE_P3 0x3
+#define AVS_PSTATE_P4 0x4
+#define AVS_PSTATE_MAX AVS_PSTATE_P4
+
+/* CPU L2 Interrupt Controller Registers */
+#define AVS_CPU_L2_SET0 0x04
+#define AVS_CPU_L2_INT_MASK BIT(31)
+
+/* AVS Command Status Values */
+#define AVS_STATUS_CLEAR 0x00
+/* Command/notification accepted */
+#define AVS_STATUS_SUCCESS 0xf0
+/* Command/notification rejected */
+#define AVS_STATUS_FAILURE 0xff
+/* Invalid command/notification (unknown) */
+#define AVS_STATUS_INVALID 0xf1
+/* Non-AVS modes are not supported */
+#define AVS_STATUS_NO_SUPP 0xf2
+/* Cannot set P-State until P-Map supplied */
+#define AVS_STATUS_NO_MAP 0xf3
+/* Cannot change P-Map after initial P-Map set */
+#define AVS_STATUS_MAP_SET 0xf4
+/* Max AVS status; higher numbers are used for debugging */
+#define AVS_STATUS_MAX 0xff
+
+/* Other AVS related constants */
+#define AVS_LOOP_LIMIT 10000
+#define AVS_TIMEOUT 300 /* in ms; expected completion is < 10ms */
+#define AVS_FIRMWARE_MAGIC 0xa11600d1
+
+#define BRCM_AVS_CPUFREQ_PREFIX "brcmstb-avs"
+#define BRCM_AVS_CPUFREQ_NAME BRCM_AVS_CPUFREQ_PREFIX "-cpufreq"
+#define BRCM_AVS_CPU_DATA "brcm,avs-cpu-data-mem"
+#define BRCM_AVS_CPU_INTR "brcm,avs-cpu-l2-intr"
+#define BRCM_AVS_HOST_INTR "sw_intr"
+
+struct pmap {
+ unsigned int mode;
+ unsigned int p1;
+ unsigned int p2;
+ unsigned int state;
+};
+
+struct private_data {
+ void __iomem *base;
+ void __iomem *avs_intr_base;
+ struct device *dev;
+ struct completion done;
+ struct semaphore sem;
+ struct pmap pmap;
+};
+
+static void __iomem *__map_region(const char *name)
+{
+ struct device_node *np;
+ void __iomem *ptr;
+
+ np = of_find_compatible_node(NULL, NULL, name);
+ if (!np)
+ return NULL;
+
+ ptr = of_iomap(np, 0);
+ of_node_put(np);
+
+ return ptr;
+}
+
+static int __issue_avs_command(struct private_data *priv, int cmd, bool is_send,
+ u32 args[])
+{
+ unsigned long time_left = msecs_to_jiffies(AVS_TIMEOUT);
+ void __iomem *base = priv->base;
+ unsigned int i;
+ int ret;
+ u32 val;
+
+ ret = down_interruptible(&priv->sem);
+ if (ret)
+ return ret;
+
+ /*
+ * Make sure no other command is currently running: cmd is 0 if AVS
+ * co-processor is idle. Due to the guard above, we should almost never
+ * have to wait here.
+ */
+ for (i = 0, val = 1; val != 0 && i < AVS_LOOP_LIMIT; i++)
+ val = readl(base + AVS_MBOX_COMMAND);
+
+ /* Give the caller a chance to retry if AVS is busy. */
+ if (i == AVS_LOOP_LIMIT) {
+ ret = -EAGAIN;
+ goto out;
+ }
+
+ /* Clear status before we begin. */
+ writel(AVS_STATUS_CLEAR, base + AVS_MBOX_STATUS);
+
+ /* We need to send arguments for this command. */
+ if (args && is_send) {
+ for (i = 0; i < AVS_MAX_CMD_ARGS; i++)
+ writel(args[i], base + AVS_MBOX_PARAM(i));
+ }
+
+ /* Protect from spurious interrupts. */
+ reinit_completion(&priv->done);
+
+ /* Now issue the command & tell firmware to wake up to process it. */
+ writel(cmd, base + AVS_MBOX_COMMAND);
+ writel(AVS_CPU_L2_INT_MASK, priv->avs_intr_base + AVS_CPU_L2_SET0);
+
+ /* Wait for AVS co-processor to finish processing the command. */
+ time_left = wait_for_completion_timeout(&priv->done, time_left);
+
+ /*
+ * If the AVS status is not in the expected range, it means AVS didn't
+ * complete our command in time, and we return an error. Also, if there
+ * is no "time left", we timed out waiting for the interrupt.
+ */
+ val = readl(base + AVS_MBOX_STATUS);
+ if (time_left == 0 || val == 0 || val > AVS_STATUS_MAX) {
+ dev_err(priv->dev, "AVS command %#x didn't complete in time\n",
+ cmd);
+ dev_err(priv->dev, " Time left: %u ms, AVS status: %#x\n",
+ jiffies_to_msecs(time_left), val);
+ ret = -ETIMEDOUT;
+ goto out;
+ }
+
+ /* This command returned arguments, so we read them back. */
+ if (args && !is_send) {
+ for (i = 0; i < AVS_MAX_CMD_ARGS; i++)
+ args[i] = readl(base + AVS_MBOX_PARAM(i));
+ }
+
+ /* Clear status to tell AVS co-processor we are done. */
+ writel(AVS_STATUS_CLEAR, base + AVS_MBOX_STATUS);
+
+ /* Convert firmware errors to errno's as much as possible. */
+ switch (val) {
+ case AVS_STATUS_INVALID:
+ ret = -EINVAL;
+ break;
+ case AVS_STATUS_NO_SUPP:
+ ret = -ENOTSUPP;
+ break;
+ case AVS_STATUS_NO_MAP:
+ ret = -ENOENT;
+ break;
+ case AVS_STATUS_MAP_SET:
+ ret = -EEXIST;
+ break;
+ case AVS_STATUS_FAILURE:
+ ret = -EIO;
+ break;
+ }
+
+out:
+ up(&priv->sem);
+
+ return ret;
+}
+
+static irqreturn_t irq_handler(int irq, void *data)
+{
+ struct private_data *priv = data;
+
+ /* AVS command completed execution. Wake up __issue_avs_command(). */
+ complete(&priv->done);
+
+ return IRQ_HANDLED;
+}
+
+static char *brcm_avs_mode_to_string(unsigned int mode)
+{
+ switch (mode) {
+ case AVS_MODE_AVS:
+ return "AVS";
+ case AVS_MODE_DFS:
+ return "DFS";
+ case AVS_MODE_DVS:
+ return "DVS";
+ case AVS_MODE_DVFS:
+ return "DVFS";
+ }
+ return NULL;
+}
+
+static void brcm_avs_parse_p1(u32 p1, unsigned int *mdiv_p0, unsigned int *pdiv,
+ unsigned int *ndiv)
+{
+ *mdiv_p0 = (p1 >> MDIV_P0_SHIFT) & MDIV_P0_MASK;
+ *pdiv = (p1 >> PDIV_SHIFT) & PDIV_MASK;
+ *ndiv = (p1 >> NDIV_INT_SHIFT) & NDIV_INT_MASK;
+}
+
+static void brcm_avs_parse_p2(u32 p2, unsigned int *mdiv_p1,
+ unsigned int *mdiv_p2, unsigned int *mdiv_p3,
+ unsigned int *mdiv_p4)
+{
+ *mdiv_p4 = (p2 >> MDIV_P4_SHIFT) & MDIV_P4_MASK;
+ *mdiv_p3 = (p2 >> MDIV_P3_SHIFT) & MDIV_P3_MASK;
+ *mdiv_p2 = (p2 >> MDIV_P2_SHIFT) & MDIV_P2_MASK;
+ *mdiv_p1 = (p2 >> MDIV_P1_SHIFT) & MDIV_P1_MASK;
+}
+
+static int brcm_avs_get_pmap(struct private_data *priv, struct pmap *pmap)
+{
+ u32 args[AVS_MAX_CMD_ARGS];
+ int ret;
+
+ ret = __issue_avs_command(priv, AVS_CMD_GET_PMAP, false, args);
+ if (ret || !pmap)
+ return ret;
+
+ pmap->mode = args[0];
+ pmap->p1 = args[1];
+ pmap->p2 = args[2];
+ pmap->state = args[3];
+
+ return 0;
+}
+
+static int brcm_avs_set_pmap(struct private_data *priv, struct pmap *pmap)
+{
+ u32 args[AVS_MAX_CMD_ARGS];
+
+ args[0] = pmap->mode;
+ args[1] = pmap->p1;
+ args[2] = pmap->p2;
+ args[3] = pmap->state;
+
+ return __issue_avs_command(priv, AVS_CMD_SET_PMAP, true, args);
+}
+
+static int brcm_avs_get_pstate(struct private_data *priv, unsigned int *pstate)
+{
+ u32 args[AVS_MAX_CMD_ARGS];
+ int ret;
+
+ ret = __issue_avs_command(priv, AVS_CMD_GET_PSTATE, false, args);
+ if (ret)
+ return ret;
+ *pstate = args[0];
+
+ return 0;
+}
+
+static int brcm_avs_set_pstate(struct private_data *priv, unsigned int pstate)
+{
+ u32 args[AVS_MAX_CMD_ARGS];
+
+ args[0] = pstate;
+
+ return __issue_avs_command(priv, AVS_CMD_SET_PSTATE, true, args);
+}
+
+static unsigned long brcm_avs_get_voltage(void __iomem *base)
+{
+ return readl(base + AVS_MBOX_VOLTAGE1);
+}
+
+static unsigned long brcm_avs_get_frequency(void __iomem *base)
+{
+ return readl(base + AVS_MBOX_FREQUENCY) * 1000; /* in kHz */
+}
+
+/*
+ * We determine which frequencies are supported by cycling through all P-states
+ * and reading back what frequency we are running at for each P-state.
+ */
+static struct cpufreq_frequency_table *
+brcm_avs_get_freq_table(struct device *dev, struct private_data *priv)
+{
+ struct cpufreq_frequency_table *table;
+ unsigned int pstate;
+ int i, ret;
+
+ /* Remember P-state for later */
+ ret = brcm_avs_get_pstate(priv, &pstate);
+ if (ret)
+ return ERR_PTR(ret);
+
+ table = devm_kzalloc(dev, (AVS_PSTATE_MAX + 1) * sizeof(*table),
+ GFP_KERNEL);
+ if (!table)
+ return ERR_PTR(-ENOMEM);
+
+ for (i = AVS_PSTATE_P0; i <= AVS_PSTATE_MAX; i++) {
+ ret = brcm_avs_set_pstate(priv, i);
+ if (ret)
+ return ERR_PTR(ret);
+ table[i].frequency = brcm_avs_get_frequency(priv->base);
+ table[i].driver_data = i;
+ }
+ table[i].frequency = CPUFREQ_TABLE_END;
+
+ /* Restore P-state */
+ ret = brcm_avs_set_pstate(priv, pstate);
+ if (ret)
+ return ERR_PTR(ret);
+
+ return table;
+}
+
+/*
+ * To ensure the right firmware is running we need to
+ * - check the MAGIC matches what we expect
+ * - brcm_avs_get_pmap() doesn't return -ENOTSUPP or -EINVAL
+ * We need to set up our interrupt handling before calling brcm_avs_get_pmap()!
+ */
+static bool brcm_avs_is_firmware_loaded(struct private_data *priv)
+{
+ u32 magic;
+ int rc;
+
+ rc = brcm_avs_get_pmap(priv, NULL);
+ magic = readl(priv->base + AVS_MBOX_MAGIC);
+
+ return (magic == AVS_FIRMWARE_MAGIC) && (rc != -ENOTSUPP) &&
+ (rc != -EINVAL);
+}
+
+static unsigned int brcm_avs_cpufreq_get(unsigned int cpu)
+{
+ struct cpufreq_policy *policy = cpufreq_cpu_get(cpu);
+ struct private_data *priv = policy->driver_data;
+
+ return brcm_avs_get_frequency(priv->base);
+}
+
+static int brcm_avs_target_index(struct cpufreq_policy *policy,
+ unsigned int index)
+{
+ return brcm_avs_set_pstate(policy->driver_data,
+ policy->freq_table[index].driver_data);
+}
+
+static int brcm_avs_suspend(struct cpufreq_policy *policy)
+{
+ struct private_data *priv = policy->driver_data;
+
+ return brcm_avs_get_pmap(priv, &priv->pmap);
+}
+
+static int brcm_avs_resume(struct cpufreq_policy *policy)
+{
+ struct private_data *priv = policy->driver_data;
+ int ret;
+
+ ret = brcm_avs_set_pmap(priv, &priv->pmap);
+ if (ret == -EEXIST) {
+ struct platform_device *pdev = cpufreq_get_driver_data();
+ struct device *dev = &pdev->dev;
+
+ dev_warn(dev, "PMAP was already set\n");
+ ret = 0;
+ }
+
+ return ret;
+}
+
+/*
+ * All initialization code that we only want to execute once goes here. Setup
+ * code that can be re-tried on every core (if it failed before) can go into
+ * brcm_avs_cpufreq_init().
+ */
+static int brcm_avs_prepare_init(struct platform_device *pdev)
+{
+ struct private_data *priv;
+ struct device *dev;
+ int host_irq, ret;
+
+ dev = &pdev->dev;
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ priv->dev = dev;
+ sema_init(&priv->sem, 1);
+ init_completion(&priv->done);
+ platform_set_drvdata(pdev, priv);
+
+ priv->base = __map_region(BRCM_AVS_CPU_DATA);
+ if (!priv->base) {
+ dev_err(dev, "Couldn't find property %s in device tree.\n",
+ BRCM_AVS_CPU_DATA);
+ return -ENOENT;
+ }
+
+ priv->avs_intr_base = __map_region(BRCM_AVS_CPU_INTR);
+ if (!priv->avs_intr_base) {
+ dev_err(dev, "Couldn't find property %s in device tree.\n",
+ BRCM_AVS_CPU_INTR);
+ ret = -ENOENT;
+ goto unmap_base;
+ }
+
+ host_irq = platform_get_irq_byname(pdev, BRCM_AVS_HOST_INTR);
+ if (host_irq < 0) {
+ dev_err(dev, "Couldn't find interrupt %s -- %d\n",
+ BRCM_AVS_HOST_INTR, host_irq);
+ ret = host_irq;
+ goto unmap_intr_base;
+ }
+
+ ret = devm_request_irq(dev, host_irq, irq_handler, IRQF_TRIGGER_RISING,
+ BRCM_AVS_HOST_INTR, priv);
+ if (ret) {
+ dev_err(dev, "IRQ request failed: %s (%d) -- %d\n",
+ BRCM_AVS_HOST_INTR, host_irq, ret);
+ goto unmap_intr_base;
+ }
+
+ if (brcm_avs_is_firmware_loaded(priv))
+ return 0;
+
+ dev_err(dev, "AVS firmware is not loaded or doesn't support DVFS\n");
+ ret = -ENODEV;
+
+unmap_intr_base:
+ iounmap(priv->avs_intr_base);
+unmap_base:
+ iounmap(priv->base);
+ platform_set_drvdata(pdev, NULL);
+
+ return ret;
+}
+
+static int brcm_avs_cpufreq_init(struct cpufreq_policy *policy)
+{
+ struct cpufreq_frequency_table *freq_table;
+ struct platform_device *pdev;
+ struct private_data *priv;
+ struct device *dev;
+ int ret;
+
+ pdev = cpufreq_get_driver_data();
+ priv = platform_get_drvdata(pdev);
+ policy->driver_data = priv;
+ dev = &pdev->dev;
+
+ freq_table = brcm_avs_get_freq_table(dev, priv);
+ if (IS_ERR(freq_table)) {
+ ret = PTR_ERR(freq_table);
+ dev_err(dev, "Couldn't determine frequency table (%d).\n", ret);
+ return ret;
+ }
+
+ ret = cpufreq_table_validate_and_show(policy, freq_table);
+ if (ret) {
+ dev_err(dev, "invalid frequency table: %d\n", ret);
+ return ret;
+ }
+
+ /* All cores share the same clock and thus the same policy. */
+ cpumask_setall(policy->cpus);
+
+ ret = __issue_avs_command(priv, AVS_CMD_ENABLE, false, NULL);
+ if (!ret) {
+ unsigned int pstate;
+
+ ret = brcm_avs_get_pstate(priv, &pstate);
+ if (!ret) {
+ policy->cur = freq_table[pstate].frequency;
+ dev_info(dev, "registered\n");
+ return 0;
+ }
+ }
+
+ dev_err(dev, "couldn't initialize driver (%d)\n", ret);
+
+ return ret;
+}
+
+static ssize_t show_brcm_avs_pstate(struct cpufreq_policy *policy, char *buf)
+{
+ struct private_data *priv = policy->driver_data;
+ unsigned int pstate;
+
+ if (brcm_avs_get_pstate(priv, &pstate))
+ return sprintf(buf, "<unknown>\n");
+
+ return sprintf(buf, "%u\n", pstate);
+}
+
+static ssize_t show_brcm_avs_mode(struct cpufreq_policy *policy, char *buf)
+{
+ struct private_data *priv = policy->driver_data;
+ struct pmap pmap;
+
+ if (brcm_avs_get_pmap(priv, &pmap))
+ return sprintf(buf, "<unknown>\n");
+
+ return sprintf(buf, "%s %u\n", brcm_avs_mode_to_string(pmap.mode),
+ pmap.mode);
+}
+
+static ssize_t show_brcm_avs_pmap(struct cpufreq_policy *policy, char *buf)
+{
+ unsigned int mdiv_p0, mdiv_p1, mdiv_p2, mdiv_p3, mdiv_p4;
+ struct private_data *priv = policy->driver_data;
+ unsigned int ndiv, pdiv;
+ struct pmap pmap;
+
+ if (brcm_avs_get_pmap(priv, &pmap))
+ return sprintf(buf, "<unknown>\n");
+
+ brcm_avs_parse_p1(pmap.p1, &mdiv_p0, &pdiv, &ndiv);
+ brcm_avs_parse_p2(pmap.p2, &mdiv_p1, &mdiv_p2, &mdiv_p3, &mdiv_p4);
+
+ return sprintf(buf, "0x%08x 0x%08x %u %u %u %u %u %u %u\n",
+ pmap.p1, pmap.p2, ndiv, pdiv, mdiv_p0, mdiv_p1, mdiv_p2,
+ mdiv_p3, mdiv_p4);
+}
+
+static ssize_t show_brcm_avs_voltage(struct cpufreq_policy *policy, char *buf)
+{
+ struct private_data *priv = policy->driver_data;
+
+ return sprintf(buf, "0x%08lx\n", brcm_avs_get_voltage(priv->base));
+}
+
+static ssize_t show_brcm_avs_frequency(struct cpufreq_policy *policy, char *buf)
+{
+ struct private_data *priv = policy->driver_data;
+
+ return sprintf(buf, "0x%08lx\n", brcm_avs_get_frequency(priv->base));
+}
+
+cpufreq_freq_attr_ro(brcm_avs_pstate);
+cpufreq_freq_attr_ro(brcm_avs_mode);
+cpufreq_freq_attr_ro(brcm_avs_pmap);
+cpufreq_freq_attr_ro(brcm_avs_voltage);
+cpufreq_freq_attr_ro(brcm_avs_frequency);
+
+struct freq_attr *brcm_avs_cpufreq_attr[] = {
+ &cpufreq_freq_attr_scaling_available_freqs,
+ &brcm_avs_pstate,
+ &brcm_avs_mode,
+ &brcm_avs_pmap,
+ &brcm_avs_voltage,
+ &brcm_avs_frequency,
+ NULL
+};
+
+static struct cpufreq_driver brcm_avs_driver = {
+ .flags = CPUFREQ_NEED_INITIAL_FREQ_CHECK,
+ .verify = cpufreq_generic_frequency_table_verify,
+ .target_index = brcm_avs_target_index,
+ .get = brcm_avs_cpufreq_get,
+ .suspend = brcm_avs_suspend,
+ .resume = brcm_avs_resume,
+ .init = brcm_avs_cpufreq_init,
+ .attr = brcm_avs_cpufreq_attr,
+ .name = BRCM_AVS_CPUFREQ_PREFIX,
+};
+
+static int brcm_avs_cpufreq_probe(struct platform_device *pdev)
+{
+ int ret;
+
+ ret = brcm_avs_prepare_init(pdev);
+ if (ret)
+ return ret;
+
+ brcm_avs_driver.driver_data = pdev;
+
+ return cpufreq_register_driver(&brcm_avs_driver);
+}
+
+static int brcm_avs_cpufreq_remove(struct platform_device *pdev)
+{
+ struct private_data *priv;
+ int ret;
+
+ ret = cpufreq_unregister_driver(&brcm_avs_driver);
+ if (ret)
+ return ret;
+
+ priv = platform_get_drvdata(pdev);
+ iounmap(priv->base);
+ iounmap(priv->avs_intr_base);
+ platform_set_drvdata(pdev, NULL);
+
+ return 0;
+}
+
+static const struct of_device_id brcm_avs_cpufreq_match[] = {
+ { .compatible = BRCM_AVS_CPU_DATA },
+ { }
+};
+MODULE_DEVICE_TABLE(of, brcm_avs_cpufreq_match);
+
+static struct platform_driver brcm_avs_cpufreq_platdrv = {
+ .driver = {
+ .name = BRCM_AVS_CPUFREQ_NAME,
+ .of_match_table = brcm_avs_cpufreq_match,
+ },
+ .probe = brcm_avs_cpufreq_probe,
+ .remove = brcm_avs_cpufreq_remove,
+};
+module_platform_driver(brcm_avs_cpufreq_platdrv);
+
+MODULE_AUTHOR("Markus Mayer <[email protected]>");
+MODULE_DESCRIPTION("CPUfreq driver for Broadcom STB AVS");
+MODULE_LICENSE("GPL");
--
2.7.4

2016-10-31 05:43:07

by Rob Herring (Arm)

[permalink] [raw]
Subject: Re: [PATCH v5 1/3] dt: cpufreq: brcm: New binding document for brcmstb-avs-cpufreq

On Thu, Oct 27, 2016 at 02:05:34PM -0700, Markus Mayer wrote:
> From: Markus Mayer <[email protected]>
>
> Add the binding document for the new brcmstb-avs-cpufreq driver.
>
> Signed-off-by: Markus Mayer <[email protected]>
> Acked-by: Viresh Kumar <[email protected]>
> ---
> .../bindings/cpufreq/brcm,stb-avs-cpu-freq.txt | 78 ++++++++++++++++++++++
> MAINTAINERS | 7 ++
> 2 files changed, 85 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/cpufreq/brcm,stb-avs-cpu-freq.txt

I guess if one of the nodes is used elsewhere, combining the nodes
doesn't make sense. So:

Acked-by: Rob Herring <[email protected]>

2016-10-31 16:37:46

by Markus Mayer

[permalink] [raw]
Subject: Re: [PATCH v5 1/3] dt: cpufreq: brcm: New binding document for brcmstb-avs-cpufreq

On 30 October 2016 at 22:43, Rob Herring <[email protected]> wrote:
> On Thu, Oct 27, 2016 at 02:05:34PM -0700, Markus Mayer wrote:
>> From: Markus Mayer <[email protected]>
>>
>> Add the binding document for the new brcmstb-avs-cpufreq driver.
>>
>> Signed-off-by: Markus Mayer <[email protected]>
>> Acked-by: Viresh Kumar <[email protected]>
>> ---
>> .../bindings/cpufreq/brcm,stb-avs-cpu-freq.txt | 78 ++++++++++++++++++++++
>> MAINTAINERS | 7 ++
>> 2 files changed, 85 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/cpufreq/brcm,stb-avs-cpu-freq.txt
>
> I guess if one of the nodes is used elsewhere, combining the nodes
> doesn't make sense. So:
>
> Acked-by: Rob Herring <[email protected]>

Thanks, Rob.

The series, with Acks added, is also available here:
https://github.com/mmayer/linux/tree/upstream-avs-cpufreq-4.9-v5

Regards,
-Markus

2016-11-04 17:00:23

by Markus Mayer

[permalink] [raw]
Subject: Re: [PATCH v5 0/3] Broadcom STB AVS CPUfreq driver

On 27 October 2016 at 14:05, Markus Mayer <[email protected]> wrote:
> From: Markus Mayer <[email protected]>
>
> This series contains the CPUfreq driver for Broadcom SoCs that use "AVS
> Firmware" for voltage and frequency scaling. All voltage and frequency
> transitions are performed by the firmware and are therefore hidden from
> Linux.
>
> The driver provides a standard CPUfreq interface to other kernel
> components and to userland on the one hand and communicates with the
> AVS co-processor on the other.
>
> Communication between the two processors is via shared mailbox
> registers and interrupts (ARM -> AVS to tell the firmware that there is
> a command to process and AVS -> ARM to tell the driver that a command
> finished executing).

Viresh, Rafael, are you ready to take this series? Rob gave his Ack
for the DT binding.

You can pull from [1] if you prefer. The branch already has all the Acks.

Thanks,
-Markus

[1] https://github.com/mmayer/linux/commits/upstream-avs-cpufreq-4.9-v5

> Changes from v4:
> - Addressed comments regarding the binding document (see also
> https://lkml.org/lkml/2016/10/19/642)
> - Added Virsh's Acks
> - Rebased on v4.9-rc1
> - Patches sent from non-Broadcom account on purpose to prevent series
> from being marked as spam (this is currently happening for some
> recipients)
> - No changes to any code
>
> Changes from v3:
> - moved code from brcm_avs_cpufreq_exit() into brcm_avs_cpufreq_remove()
> - removed brcm_avs_cpufreq_exit() altogether
>
> Changes from v2:
> - removed file Documentation/cpu-freq/brcmstb-avs-cpufreq.txt, instead
> adding the text as comment in the driver itself
> - wildcard match in MAINTAINERS file (drivers/cpufreq/brcmstb*)
> - drivers/cpufreq/Kconfig.arm: have ARM_BRCMSTB_AVS_CPUFREQ default y
> for ARCH_BRCMSTB
> - fixed naming and Kconfig entry for CONFIG_ARM_BRCMSTB_AVS_CPUFREQ_DEBUG
> - reordered and fixed include files
> - made sure driver name doesn't exceed size of cpufreq_driver.name
> - got rid of device_node pointers in struct private_data; there's no
> need for them, as we can call of_node_put() in __map_region()
> - don't set driver_data for CPUFREQ_TABLE_END
> - have brcm_avs_cpufreq_get() read from the firmware rather than return
> policy->cur
> - don't update policy->cur in brcm_avs_target_index()
> - created new function brcm_avs_prepare_init() to handle compatibility
> checks during initialization and moved corresponding code from
> brcm_avs_cpufreq_init() to the new function
> - brcm_avs_prepare_init() is called from brcm_avs_cpufreq_probe() and
> therefore will only be called once, even in the case of an error,
> whereas brcm_avs_cpufreq_init() is called for every core if there is
> an error
> - renamed brcm_avs_cpu_(init|exit) to brcm_avs_cpufreq_(init|exit)
> - added platform_set_drvdata(pdev, NULL) upon deregistration
> - fixed various style complaints by checkpatch.pl --strict
> - fixed other style issues
> - updated and improved some comments
> - added Viresh's Acks to patches 1/3 and 3/3
>
> Changes from v1:
> - renamed binding document
> - rewrote the introduction of the binding document
> - created a new driver documentation file that contains Linux specific
> information that was previously part of the binding document
> - renamed the driver (and related config options) to include a reference
> to "STB", since this implementation is primarily intended for use on
> set-top boxes
> - improved comments
> - updated function __map_region()
> - updated struct private_data
> - added code to unmap memory regions in the error and exit paths
> - added new sysfs property to report frequency directly from the
> co-processor register
>
> Markus Mayer (3):
> dt: cpufreq: brcm: New binding document for brcmstb-avs-cpufreq
> cpufreq: brcmstb-avs-cpufreq: AVS CPUfreq driver for Broadcom STB SoCs
> cpufreq: brcmstb-avs-cpufreq: add debugfs support
>
> .../bindings/cpufreq/brcm,stb-avs-cpu-freq.txt | 78 ++
> MAINTAINERS | 8 +
> drivers/cpufreq/Kconfig.arm | 21 +
> drivers/cpufreq/Makefile | 1 +
> drivers/cpufreq/brcmstb-avs-cpufreq.c | 1057 ++++++++++++++++++++
> 5 files changed, 1165 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/cpufreq/brcm,stb-avs-cpu-freq.txt
> create mode 100644 drivers/cpufreq/brcmstb-avs-cpufreq.c
>
> --
> 2.7.4
>

2016-11-14 00:25:14

by Rafael J. Wysocki

[permalink] [raw]
Subject: Re: [PATCH v5 0/3] Broadcom STB AVS CPUfreq driver

On Friday, November 04, 2016 10:00:19 AM Markus Mayer wrote:
> On 27 October 2016 at 14:05, Markus Mayer <[email protected]> wrote:
> > From: Markus Mayer <[email protected]>
> >
> > This series contains the CPUfreq driver for Broadcom SoCs that use "AVS
> > Firmware" for voltage and frequency scaling. All voltage and frequency
> > transitions are performed by the firmware and are therefore hidden from
> > Linux.
> >
> > The driver provides a standard CPUfreq interface to other kernel
> > components and to userland on the one hand and communicates with the
> > AVS co-processor on the other.
> >
> > Communication between the two processors is via shared mailbox
> > registers and interrupts (ARM -> AVS to tell the firmware that there is
> > a command to process and AVS -> ARM to tell the driver that a command
> > finished executing).
>
> Viresh, Rafael, are you ready to take this series? Rob gave his Ack
> for the DT binding.

Applied.

Thanks,
Rafael