Stephen Boyd pointed out that the current design of the Qualcomm RPM and
regulator driver consumes 12-20kB of ram just for the platform_device structs.
This third iteration of the patch comes with a patch at the end to tidy up the
probe function - after the various refactorings.
Dropped from the series is the patch to add "regulator-allow-drms"; so it has a
functional dependency towards such a patch, to get drms handling running again.
But if Stephen is fine with patch 5 as answer to his concerns with patch 4 I
think we should merge this.
Changes since v2:
- Dropped unrelated drms dt property patch
- Fixed minor spelling misstake in dt binding
- Added patch to tidy up probe function
Changes since v1:
- Reworked DRMS handling to not have the driver specify the support
Bjorn Andersson (5):
mfd: devicetree: bindings: Add Qualcomm RPM regulator subnodes
regulator: qcom: Don't enable DRMS in driver
regulator: qcom: Refactor of-parsing code
regulator: qcom: Rework to single platform device
regulator: qcom: Tidy up probe()
Documentation/devicetree/bindings/mfd/qcom-rpm.txt | 217 ++++++++++++++-
drivers/regulator/qcom_rpm-regulator.c | 290 ++++++++++++++-------
2 files changed, 398 insertions(+), 109 deletions(-)
--
1.8.2.2
Add the regulator subnodes to the Qualcomm RPM MFD device tree bindings.
Reviewed-by: Stephen Boyd <[email protected]>
Signed-off-by: Bjorn Andersson <[email protected]>
---
Changes since v2:
- s/notes/nodes from Stephen
Documentation/devicetree/bindings/mfd/qcom-rpm.txt | 217 +++++++++++++++++++--
1 file changed, 205 insertions(+), 12 deletions(-)
diff --git a/Documentation/devicetree/bindings/mfd/qcom-rpm.txt b/Documentation/devicetree/bindings/mfd/qcom-rpm.txt
index 85e3198..f7c22c5 100644
--- a/Documentation/devicetree/bindings/mfd/qcom-rpm.txt
+++ b/Documentation/devicetree/bindings/mfd/qcom-rpm.txt
@@ -31,16 +31,6 @@ frequencies.
Value type: <string-array>
Definition: must be the three strings "ack", "err" and "wakeup", in order
-- #address-cells:
- Usage: required
- Value type: <u32>
- Definition: must be 1
-
-- #size-cells:
- Usage: required
- Value type: <u32>
- Definition: must be 0
-
- qcom,ipc:
Usage: required
Value type: <prop-encoded-array>
@@ -52,6 +42,188 @@ frequencies.
- u32 representing the ipc bit within the register
+= SUBNODES
+
+The RPM exposes resources to its subnodes. The below bindings specify the set
+of valid subnodes that can operate on these resources.
+
+== Regulators
+
+Regulator nodes are identified by their compatible:
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: must be one of:
+ "qcom,rpm-pm8058-regulators"
+ "qcom,rpm-pm8901-regulators"
+ "qcom,rpm-pm8921-regulators"
+
+- vdd_l0_l1_lvs-supply:
+- vdd_l2_l11_l12-supply:
+- vdd_l3_l4_l5-supply:
+- vdd_l6_l7-supply:
+- vdd_l8-supply:
+- vdd_l9-supply:
+- vdd_l10-supply:
+- vdd_l13_l16-supply:
+- vdd_l14_l15-supply:
+- vdd_l17_l18-supply:
+- vdd_l19_l20-supply:
+- vdd_l21-supply:
+- vdd_l22-supply:
+- vdd_l23_l24_l25-supply:
+- vdd_ncp-supply:
+- vdd_s0-supply:
+- vdd_s1-supply:
+- vdd_s2-supply:
+- vdd_s3-supply:
+- vdd_s4-supply:
+ Usage: optional (pm8058 only)
+ Value type: <phandle>
+ Definition: reference to regulator supplying the input pin, as
+ described in the data sheet
+
+- lvs0_in-supply:
+- lvs1_in-supply:
+- lvs2_in-supply:
+- lvs3_in-supply:
+- mvs_in-supply:
+- vdd_l0-supply:
+- vdd_l1-supply:
+- vdd_l2-supply:
+- vdd_l3-supply:
+- vdd_l4-supply:
+- vdd_l5-supply:
+- vdd_l6-supply:
+- vdd_s0-supply:
+- vdd_s1-supply:
+- vdd_s2-supply:
+- vdd_s3-supply:
+- vdd_s4-supply:
+ Usage: optional (pm8901 only)
+ Value type: <phandle>
+ Definition: reference to regulator supplying the input pin, as
+ described in the data sheet
+
+- vdd_l1_l2_l12_l18-supply:
+- vdd_l3_l15_l17-supply:
+- vdd_l4_l14-supply:
+- vdd_l5_l8_l16-supply:
+- vdd_l6_l7-supply:
+- vdd_l9_l11-supply:
+- vdd_l10_l22-supply:
+- vdd_l21_l23_l29-supply:
+- vdd_l24-supply:
+- vdd_l25-supply:
+- vdd_l26-supply:
+- vdd_l27-supply:
+- vdd_l28-supply:
+- vdd_ncp-supply:
+- vdd_s1-supply:
+- vdd_s2-supply:
+- vdd_s4-supply:
+- vdd_s5-supply:
+- vdd_s6-supply:
+- vdd_s7-supply:
+- vdd_s8-supply:
+- vin_5vs-supply:
+- vin_lvs1_3_6-supply:
+- vin_lvs2-supply:
+- vin_lvs4_5_7-supply:
+ Usage: optional (pm8921 only)
+ Value type: <phandle>
+ Definition: reference to regulator supplying the input pin, as
+ described in the data sheet
+
+The regulator node houses sub-nodes for each regulator within the device. Each
+sub-node is identified using the node's name, with valid values listed for each
+of the pmics below.
+
+pm8058:
+ l0, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, l14, l15,
+ l16, l17, l18, l19, l20, l21, l22, l23, l24, l25, s0, s1, s2, s3, s4,
+ lvs0, lvs1, ncp
+
+pm8901:
+ l0, l1, l2, l3, l4, l5, l6, s0, s1, s2, s3, s4, lvs0, lvs1, lvs2, lvs3,
+ mvs
+
+pm8921:
+ s1, s2, s3, s4, s7, s8, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11,
+ l12, l14, l15, l16, l17, l18, l21, l22, l23, l24, l25, l26, l27, l28,
+ l29, lvs1, lvs2, lvs3, lvs4, lvs5, lvs6, lvs7, usb-switch, hdmi-switch,
+ ncp
+
+The content of each sub-node is defined by the standard binding for regulators -
+see regulator.txt - with additional custom properties described below:
+
+=== Switch-mode Power Supply regulator custom properties
+
+- bias-pull-down:
+ Usage: optional
+ Value type: <empty>
+ Definition: enable pull down of the regulator when inactive
+
+- qcom,switch-mode-frequency:
+ Usage: required
+ Value type: <u32>
+ Definition: Frequency (Hz) of the switch-mode power supply;
+ must be one of:
+ 19200000, 9600000, 6400000, 4800000, 3840000, 3200000,
+ 2740000, 2400000, 2130000, 1920000, 1750000, 1600000,
+ 1480000, 1370000, 1280000, 1200000
+
+- qcom,force-mode:
+ Usage: optional (default if no other qcom,force-mode is specified)
+ Value type: <u32>
+ Defintion: indicates that the regulator should be forced to a
+ particular mode, valid values are:
+ QCOM_RPM_FORCE_MODE_NONE - do not force any mode
+ QCOM_RPM_FORCE_MODE_LPM - force into low power mode
+ QCOM_RPM_FORCE_MODE_HPM - force into high power mode
+ QCOM_RPM_FORCE_MODE_AUTO - allow regulator to automatically
+ select its own mode based on
+ realtime current draw, only for:
+ pm8921 smps and ftsmps
+
+- qcom,power-mode-hysteretic:
+ Usage: optional
+ Value type: <empty>
+ Definition: select that the power supply should operate in hysteretic
+ mode, instead of the default pwm mode
+
+=== Low-dropout regulator custom properties
+
+- bias-pull-down:
+ Usage: optional
+ Value type: <empty>
+ Definition: enable pull down of the regulator when inactive
+
+- qcom,force-mode:
+ Usage: optional
+ Value type: <u32>
+ Defintion: indicates that the regulator should not be forced to any
+ particular mode, valid values are:
+ QCOM_RPM_FORCE_MODE_NONE - do not force any mode
+ QCOM_RPM_FORCE_MODE_LPM - force into low power mode
+ QCOM_RPM_FORCE_MODE_HPM - force into high power mode
+ QCOM_RPM_FORCE_MODE_BYPASS - set regulator to use bypass
+ mode, i.e. to act as a switch
+ and not regulate, only for:
+ pm8921 pldo, nldo and nldo1200
+
+=== Negative Charge Pump custom properties
+
+- qcom,switch-mode-frequency:
+ Usage: required
+ Value type: <u32>
+ Definition: Frequency (Hz) of the swith mode power supply;
+ must be one of:
+ 19200000, 9600000, 6400000, 4800000, 3840000, 3200000,
+ 2740000, 2400000, 2130000, 1920000, 1750000, 1600000,
+ 1480000, 1370000, 1280000, 1200000
+
= EXAMPLE
#include <dt-bindings/mfd/qcom-rpm.h>
@@ -64,7 +236,28 @@ frequencies.
interrupts = <0 19 0>, <0 21 0>, <0 22 0>;
interrupt-names = "ack", "err", "wakeup";
- #address-cells = <1>;
- #size-cells = <0>;
+ regulators {
+ compatible = "qcom,rpm-pm8921-regulators";
+ vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+
+ s1 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+
+ bias-pull-down;
+
+ qcom,switch-mode-frequency = <3200000>;
+ };
+
+ pm8921_s4: s4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ qcom,switch-mode-frequency = <1600000>;
+ bias-pull-down;
+
+ qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
+ };
+ };
};
--
1.8.2.2
The driver itself should not flag regulators as being DRMS compatible,
this should come from board or dt files.
Reviewed-by: Stephen Boyd <[email protected]>
Signed-off-by: Bjorn Andersson <[email protected]>
---
No changes since v2
drivers/regulator/qcom_rpm-regulator.c | 4 ----
1 file changed, 4 deletions(-)
diff --git a/drivers/regulator/qcom_rpm-regulator.c b/drivers/regulator/qcom_rpm-regulator.c
index 15e07c2..ddca8cb 100644
--- a/drivers/regulator/qcom_rpm-regulator.c
+++ b/drivers/regulator/qcom_rpm-regulator.c
@@ -732,10 +732,6 @@ static int rpm_reg_probe(struct platform_device *pdev)
return -EINVAL;
}
- /* Regulators with ia property suppports drms */
- if (vreg->parts->ia.mask)
- initdata->constraints.valid_ops_mask |= REGULATOR_CHANGE_DRMS;
-
key = "bias-pull-down";
if (of_property_read_bool(pdev->dev.of_node, key)) {
ret = rpm_reg_set(vreg, &vreg->parts->pd, 1);
--
1.8.2.2
Refactor out all custom property parsing code from the probe function
into a function suitable for regulator_desc->of_parse_cb usage.
Reviewed-by: Stephen Boyd <[email protected]>
Signed-off-by: Bjorn Andersson <[email protected]>
---
No changes since v2
drivers/regulator/qcom_rpm-regulator.c | 141 +++++++++++++++++++--------------
1 file changed, 81 insertions(+), 60 deletions(-)
diff --git a/drivers/regulator/qcom_rpm-regulator.c b/drivers/regulator/qcom_rpm-regulator.c
index ddca8cb..bd8360c 100644
--- a/drivers/regulator/qcom_rpm-regulator.c
+++ b/drivers/regulator/qcom_rpm-regulator.c
@@ -645,7 +645,9 @@ static int rpm_reg_set(struct qcom_rpm_reg *vreg,
return 0;
}
-static int rpm_reg_of_parse_freq(struct device *dev, struct qcom_rpm_reg *vreg)
+static int rpm_reg_of_parse_freq(struct device *dev,
+ struct device_node *node,
+ struct qcom_rpm_reg *vreg)
{
static const int freq_table[] = {
19200000, 9600000, 6400000, 4800000, 3840000, 3200000, 2740000,
@@ -659,7 +661,7 @@ static int rpm_reg_of_parse_freq(struct device *dev, struct qcom_rpm_reg *vreg)
int i;
key = "qcom,switch-mode-frequency";
- ret = of_property_read_u32(dev->of_node, key, &freq);
+ ret = of_property_read_u32(node, key, &freq);
if (ret) {
dev_err(dev, "regulator requires %s property\n", key);
return -EINVAL;
@@ -676,84 +678,40 @@ static int rpm_reg_of_parse_freq(struct device *dev, struct qcom_rpm_reg *vreg)
return -EINVAL;
}
-static int rpm_reg_probe(struct platform_device *pdev)
+static int rpm_reg_of_parse(struct device_node *node,
+ const struct regulator_desc *desc,
+ struct regulator_config *config)
{
- struct regulator_init_data *initdata;
- const struct qcom_rpm_reg *template;
- const struct of_device_id *match;
- struct regulator_config config = { };
- struct regulator_dev *rdev;
- struct qcom_rpm_reg *vreg;
+ struct qcom_rpm_reg *vreg = config->driver_data;
+ struct device *dev = config->dev;
const char *key;
u32 force_mode;
bool pwm;
u32 val;
int ret;
- match = of_match_device(rpm_of_match, &pdev->dev);
- template = match->data;
-
- vreg = devm_kmalloc(&pdev->dev, sizeof(*vreg), GFP_KERNEL);
- if (!vreg) {
- dev_err(&pdev->dev, "failed to allocate vreg\n");
- return -ENOMEM;
- }
- memcpy(vreg, template, sizeof(*vreg));
- mutex_init(&vreg->lock);
- vreg->dev = &pdev->dev;
- vreg->desc.id = -1;
- vreg->desc.owner = THIS_MODULE;
- vreg->desc.type = REGULATOR_VOLTAGE;
- vreg->desc.name = pdev->dev.of_node->name;
- vreg->desc.supply_name = "vin";
-
- vreg->rpm = dev_get_drvdata(pdev->dev.parent);
- if (!vreg->rpm) {
- dev_err(&pdev->dev, "unable to retrieve handle to rpm\n");
- return -ENODEV;
- }
-
- initdata = of_get_regulator_init_data(&pdev->dev, pdev->dev.of_node,
- &vreg->desc);
- if (!initdata)
- return -EINVAL;
-
- key = "reg";
- ret = of_property_read_u32(pdev->dev.of_node, key, &val);
- if (ret) {
- dev_err(&pdev->dev, "failed to read %s\n", key);
- return ret;
- }
- vreg->resource = val;
-
- if ((vreg->parts->uV.mask || vreg->parts->mV.mask) &&
- (!initdata->constraints.min_uV || !initdata->constraints.max_uV)) {
- dev_err(&pdev->dev, "no voltage specified for regulator\n");
- return -EINVAL;
- }
-
key = "bias-pull-down";
- if (of_property_read_bool(pdev->dev.of_node, key)) {
+ if (of_property_read_bool(node, key)) {
ret = rpm_reg_set(vreg, &vreg->parts->pd, 1);
if (ret) {
- dev_err(&pdev->dev, "%s is invalid", key);
+ dev_err(dev, "%s is invalid", key);
return ret;
}
}
if (vreg->parts->freq.mask) {
- ret = rpm_reg_of_parse_freq(&pdev->dev, vreg);
+ ret = rpm_reg_of_parse_freq(dev, node, vreg);
if (ret < 0)
return ret;
}
if (vreg->parts->pm.mask) {
key = "qcom,power-mode-hysteretic";
- pwm = !of_property_read_bool(pdev->dev.of_node, key);
+ pwm = !of_property_read_bool(node, key);
ret = rpm_reg_set(vreg, &vreg->parts->pm, pwm);
if (ret) {
- dev_err(&pdev->dev, "failed to set power mode\n");
+ dev_err(dev, "failed to set power mode\n");
return ret;
}
}
@@ -762,11 +720,11 @@ static int rpm_reg_probe(struct platform_device *pdev)
force_mode = -1;
key = "qcom,force-mode";
- ret = of_property_read_u32(pdev->dev.of_node, key, &val);
+ ret = of_property_read_u32(node, key, &val);
if (ret == -EINVAL) {
val = QCOM_RPM_FORCE_MODE_NONE;
} else if (ret < 0) {
- dev_err(&pdev->dev, "failed to read %s\n", key);
+ dev_err(dev, "failed to read %s\n", key);
return ret;
}
@@ -801,21 +759,84 @@ static int rpm_reg_probe(struct platform_device *pdev)
}
if (force_mode == -1) {
- dev_err(&pdev->dev, "invalid force mode\n");
+ dev_err(dev, "invalid force mode\n");
return -EINVAL;
}
ret = rpm_reg_set(vreg, &vreg->parts->fm, force_mode);
if (ret) {
- dev_err(&pdev->dev, "failed to set force mode\n");
+ dev_err(dev, "failed to set force mode\n");
return ret;
}
}
+ return 0;
+}
+
+static int rpm_reg_probe(struct platform_device *pdev)
+{
+ struct regulator_init_data *initdata;
+ const struct qcom_rpm_reg *template;
+ const struct of_device_id *match;
+ struct regulator_config config = { };
+ struct regulator_dev *rdev;
+ struct qcom_rpm_reg *vreg;
+ const char *key;
+ u32 val;
+ int ret;
+
+ match = of_match_device(rpm_of_match, &pdev->dev);
+ template = match->data;
+
+ vreg = devm_kmalloc(&pdev->dev, sizeof(*vreg), GFP_KERNEL);
+ if (!vreg) {
+ dev_err(&pdev->dev, "failed to allocate vreg\n");
+ return -ENOMEM;
+ }
+ memcpy(vreg, template, sizeof(*vreg));
+ mutex_init(&vreg->lock);
+ vreg->dev = &pdev->dev;
+ vreg->desc.id = -1;
+ vreg->desc.owner = THIS_MODULE;
+ vreg->desc.type = REGULATOR_VOLTAGE;
+ vreg->desc.name = pdev->dev.of_node->name;
+ vreg->desc.supply_name = "vin";
+
+ vreg->rpm = dev_get_drvdata(pdev->dev.parent);
+ if (!vreg->rpm) {
+ dev_err(&pdev->dev, "unable to retrieve handle to rpm\n");
+ return -ENODEV;
+ }
+
+ initdata = of_get_regulator_init_data(&pdev->dev, pdev->dev.of_node,
+ &vreg->desc);
+ if (!initdata)
+ return -EINVAL;
+
+ key = "reg";
+ ret = of_property_read_u32(pdev->dev.of_node, key, &val);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to read %s\n", key);
+ return ret;
+ }
+ vreg->resource = val;
+
+ if ((vreg->parts->uV.mask || vreg->parts->mV.mask) &&
+ (!initdata->constraints.min_uV || !initdata->constraints.max_uV)) {
+ dev_err(&pdev->dev, "no voltage specified for regulator\n");
+ return -EINVAL;
+ }
+
+
config.dev = &pdev->dev;
config.init_data = initdata;
config.driver_data = vreg;
config.of_node = pdev->dev.of_node;
+
+ ret = rpm_reg_of_parse(pdev->dev.of_node, &vreg->desc, &config);
+ if (ret)
+ return ret;
+
rdev = devm_regulator_register(&pdev->dev, &vreg->desc, &config);
if (IS_ERR(rdev)) {
dev_err(&pdev->dev, "can't register regulator\n");
--
1.8.2.2
Modeling the individual RPM resources as platform devices consumes at
least 12-15kb of RAM, just to hold the platform_device structs. Rework
this to instead have one device per pmic exposed by the RPM.
With this representation we can more accurately define the input pins on
the pmic and have the supply description match the data sheet.
Suggested-by: Stephen Boyd <[email protected]>
Signed-off-by: Bjorn Andersson <[email protected]>
---
No changes since v2
drivers/regulator/qcom_rpm-regulator.c | 244 ++++++++++++++++++++++-----------
1 file changed, 161 insertions(+), 83 deletions(-)
diff --git a/drivers/regulator/qcom_rpm-regulator.c b/drivers/regulator/qcom_rpm-regulator.c
index bd8360c..40cf6ff 100644
--- a/drivers/regulator/qcom_rpm-regulator.c
+++ b/drivers/regulator/qcom_rpm-regulator.c
@@ -607,31 +607,6 @@ static const struct qcom_rpm_reg smb208_smps = {
.supports_force_mode_bypass = false,
};
-static const struct of_device_id rpm_of_match[] = {
- { .compatible = "qcom,rpm-pm8058-pldo", .data = &pm8058_pldo },
- { .compatible = "qcom,rpm-pm8058-nldo", .data = &pm8058_nldo },
- { .compatible = "qcom,rpm-pm8058-smps", .data = &pm8058_smps },
- { .compatible = "qcom,rpm-pm8058-ncp", .data = &pm8058_ncp },
- { .compatible = "qcom,rpm-pm8058-switch", .data = &pm8058_switch },
-
- { .compatible = "qcom,rpm-pm8901-pldo", .data = &pm8901_pldo },
- { .compatible = "qcom,rpm-pm8901-nldo", .data = &pm8901_nldo },
- { .compatible = "qcom,rpm-pm8901-ftsmps", .data = &pm8901_ftsmps },
- { .compatible = "qcom,rpm-pm8901-switch", .data = &pm8901_switch },
-
- { .compatible = "qcom,rpm-pm8921-pldo", .data = &pm8921_pldo },
- { .compatible = "qcom,rpm-pm8921-nldo", .data = &pm8921_nldo },
- { .compatible = "qcom,rpm-pm8921-nldo1200", .data = &pm8921_nldo1200 },
- { .compatible = "qcom,rpm-pm8921-smps", .data = &pm8921_smps },
- { .compatible = "qcom,rpm-pm8921-ftsmps", .data = &pm8921_ftsmps },
- { .compatible = "qcom,rpm-pm8921-ncp", .data = &pm8921_ncp },
- { .compatible = "qcom,rpm-pm8921-switch", .data = &pm8921_switch },
-
- { .compatible = "qcom,rpm-smb208", .data = &smb208_smps },
- { }
-};
-MODULE_DEVICE_TABLE(of, rpm_of_match);
-
static int rpm_reg_set(struct qcom_rpm_reg *vreg,
const struct request_member *req,
const int value)
@@ -773,74 +748,177 @@ static int rpm_reg_of_parse(struct device_node *node,
return 0;
}
-static int rpm_reg_probe(struct platform_device *pdev)
-{
- struct regulator_init_data *initdata;
+struct rpm_regulator_data {
+ const char *name;
+ int resource;
const struct qcom_rpm_reg *template;
- const struct of_device_id *match;
- struct regulator_config config = { };
- struct regulator_dev *rdev;
- struct qcom_rpm_reg *vreg;
- const char *key;
- u32 val;
- int ret;
+ const char *supply;
+};
+
+static const struct rpm_regulator_data rpm_pm8058_regulators[] = {
+ { "l0", QCOM_RPM_PM8058_LDO0, &pm8058_nldo, "vdd_l0_l1_lvs" },
+ { "l1", QCOM_RPM_PM8058_LDO1, &pm8058_nldo, "vdd_l0_l1_lvs" },
+ { "l2", QCOM_RPM_PM8058_LDO2, &pm8058_pldo, "vdd_l2_l11_l12" },
+ { "l3", QCOM_RPM_PM8058_LDO3, &pm8058_pldo, "vdd_l3_l4_l5" },
+ { "l4", QCOM_RPM_PM8058_LDO4, &pm8058_pldo, "vdd_l3_l4_l5" },
+ { "l5", QCOM_RPM_PM8058_LDO5, &pm8058_pldo, "vdd_l3_l4_l5" },
+ { "l6", QCOM_RPM_PM8058_LDO6, &pm8058_pldo, "vdd_l6_l7" },
+ { "l7", QCOM_RPM_PM8058_LDO7, &pm8058_pldo, "vdd_l6_l7" },
+ { "l8", QCOM_RPM_PM8058_LDO8, &pm8058_pldo, "vdd_l8" },
+ { "l9", QCOM_RPM_PM8058_LDO9, &pm8058_pldo, "vdd_l9" },
+ { "l10", QCOM_RPM_PM8058_LDO10, &pm8058_pldo, "vdd_l10" },
+ { "l11", QCOM_RPM_PM8058_LDO11, &pm8058_pldo, "vdd_l2_l11_l12" },
+ { "l12", QCOM_RPM_PM8058_LDO12, &pm8058_pldo, "vdd_l2_l11_l12" },
+ { "l13", QCOM_RPM_PM8058_LDO13, &pm8058_pldo, "vdd_l13_l16" },
+ { "l14", QCOM_RPM_PM8058_LDO14, &pm8058_pldo, "vdd_l14_l15" },
+ { "l15", QCOM_RPM_PM8058_LDO15, &pm8058_pldo, "vdd_l14_l15" },
+ { "l16", QCOM_RPM_PM8058_LDO16, &pm8058_pldo, "vdd_l13_l16" },
+ { "l17", QCOM_RPM_PM8058_LDO17, &pm8058_pldo, "vdd_l17_l18" },
+ { "l18", QCOM_RPM_PM8058_LDO18, &pm8058_pldo, "vdd_l17_l18" },
+ { "l19", QCOM_RPM_PM8058_LDO19, &pm8058_pldo, "vdd_l19_l20" },
+ { "l20", QCOM_RPM_PM8058_LDO20, &pm8058_pldo, "vdd_l19_l20" },
+ { "l21", QCOM_RPM_PM8058_LDO21, &pm8058_nldo, "vdd_l21" },
+ { "l22", QCOM_RPM_PM8058_LDO22, &pm8058_nldo, "vdd_l22" },
+ { "l23", QCOM_RPM_PM8058_LDO23, &pm8058_nldo, "vdd_l23_l24_l25" },
+ { "l24", QCOM_RPM_PM8058_LDO24, &pm8058_nldo, "vdd_l23_l24_l25" },
+ { "l25", QCOM_RPM_PM8058_LDO25, &pm8058_nldo, "vdd_l23_l24_l25" },
+
+ { "s0", QCOM_RPM_PM8058_SMPS0, &pm8058_smps, "vdd_s0" },
+ { "s1", QCOM_RPM_PM8058_SMPS1, &pm8058_smps, "vdd_s1" },
+ { "s2", QCOM_RPM_PM8058_SMPS2, &pm8058_smps, "vdd_s2" },
+ { "s3", QCOM_RPM_PM8058_SMPS3, &pm8058_smps, "vdd_s3" },
+ { "s4", QCOM_RPM_PM8058_SMPS4, &pm8058_smps, "vdd_s4" },
+
+ { "lvs0", QCOM_RPM_PM8058_LVS0, &pm8058_switch, "vdd_l0_l1_lvs" },
+ { "lvs1", QCOM_RPM_PM8058_LVS1, &pm8058_switch, "vdd_l0_l1_lvs" },
+
+ { "ncp", QCOM_RPM_PM8058_NCP, &pm8058_ncp, "vdd_ncp" },
+ { }
+};
- match = of_match_device(rpm_of_match, &pdev->dev);
- template = match->data;
+static const struct rpm_regulator_data rpm_pm8901_regulators[] = {
+ { "l0", QCOM_RPM_PM8901_LDO0, &pm8901_nldo, "vdd_l0" },
+ { "l1", QCOM_RPM_PM8901_LDO1, &pm8901_pldo, "vdd_l1" },
+ { "l2", QCOM_RPM_PM8901_LDO2, &pm8901_pldo, "vdd_l2" },
+ { "l3", QCOM_RPM_PM8901_LDO3, &pm8901_pldo, "vdd_l3" },
+ { "l4", QCOM_RPM_PM8901_LDO4, &pm8901_pldo, "vdd_l4" },
+ { "l5", QCOM_RPM_PM8901_LDO5, &pm8901_pldo, "vdd_l5" },
+ { "l6", QCOM_RPM_PM8901_LDO6, &pm8901_pldo, "vdd_l6" },
- vreg = devm_kmalloc(&pdev->dev, sizeof(*vreg), GFP_KERNEL);
- if (!vreg) {
- dev_err(&pdev->dev, "failed to allocate vreg\n");
- return -ENOMEM;
- }
- memcpy(vreg, template, sizeof(*vreg));
- mutex_init(&vreg->lock);
- vreg->dev = &pdev->dev;
- vreg->desc.id = -1;
- vreg->desc.owner = THIS_MODULE;
- vreg->desc.type = REGULATOR_VOLTAGE;
- vreg->desc.name = pdev->dev.of_node->name;
- vreg->desc.supply_name = "vin";
-
- vreg->rpm = dev_get_drvdata(pdev->dev.parent);
- if (!vreg->rpm) {
- dev_err(&pdev->dev, "unable to retrieve handle to rpm\n");
- return -ENODEV;
- }
+ { "s0", QCOM_RPM_PM8901_SMPS0, &pm8901_ftsmps, "vdd_s0" },
+ { "s1", QCOM_RPM_PM8901_SMPS1, &pm8901_ftsmps, "vdd_s1" },
+ { "s2", QCOM_RPM_PM8901_SMPS2, &pm8901_ftsmps, "vdd_s2" },
+ { "s3", QCOM_RPM_PM8901_SMPS3, &pm8901_ftsmps, "vdd_s3" },
+ { "s4", QCOM_RPM_PM8901_SMPS4, &pm8901_ftsmps, "vdd_s4" },
- initdata = of_get_regulator_init_data(&pdev->dev, pdev->dev.of_node,
- &vreg->desc);
- if (!initdata)
- return -EINVAL;
+ { "lvs0", QCOM_RPM_PM8901_LVS0, &pm8901_switch, "lvs0_in" },
+ { "lvs1", QCOM_RPM_PM8901_LVS1, &pm8901_switch, "lvs1_in" },
+ { "lvs2", QCOM_RPM_PM8901_LVS2, &pm8901_switch, "lvs2_in" },
+ { "lvs3", QCOM_RPM_PM8901_LVS3, &pm8901_switch, "lvs3_in" },
- key = "reg";
- ret = of_property_read_u32(pdev->dev.of_node, key, &val);
- if (ret) {
- dev_err(&pdev->dev, "failed to read %s\n", key);
- return ret;
- }
- vreg->resource = val;
+ { "mvs", QCOM_RPM_PM8901_MVS, &pm8901_switch, "mvs_in" },
+ { }
+};
- if ((vreg->parts->uV.mask || vreg->parts->mV.mask) &&
- (!initdata->constraints.min_uV || !initdata->constraints.max_uV)) {
- dev_err(&pdev->dev, "no voltage specified for regulator\n");
- return -EINVAL;
- }
+static const struct rpm_regulator_data rpm_pm8921_regulators[] = {
+ { "s1", QCOM_RPM_PM8921_SMPS1, &pm8921_smps, "vdd_s1" },
+ { "s2", QCOM_RPM_PM8921_SMPS2, &pm8921_smps, "vdd_s2" },
+ { "s3", QCOM_RPM_PM8921_SMPS3, &pm8921_smps },
+ { "s4", QCOM_RPM_PM8921_SMPS4, &pm8921_smps, "vdd_s4" },
+ { "s7", QCOM_RPM_PM8921_SMPS7, &pm8921_smps, "vdd_s7" },
+ { "s8", QCOM_RPM_PM8921_SMPS8, &pm8921_smps, "vdd_s8" },
+
+ { "l1", QCOM_RPM_PM8921_LDO1, &pm8921_nldo, "vdd_l1_l2_l12_l18" },
+ { "l2", QCOM_RPM_PM8921_LDO2, &pm8921_nldo, "vdd_l1_l2_l12_l18" },
+ { "l3", QCOM_RPM_PM8921_LDO3, &pm8921_pldo, "vdd_l3_l15_l17" },
+ { "l4", QCOM_RPM_PM8921_LDO4, &pm8921_pldo, "vdd_l4_l14" },
+ { "l5", QCOM_RPM_PM8921_LDO5, &pm8921_pldo, "vdd_l5_l8_l16" },
+ { "l6", QCOM_RPM_PM8921_LDO6, &pm8921_pldo, "vdd_l6_l7" },
+ { "l7", QCOM_RPM_PM8921_LDO7, &pm8921_pldo, "vdd_l6_l7" },
+ { "l8", QCOM_RPM_PM8921_LDO8, &pm8921_pldo, "vdd_l5_l8_l16" },
+ { "l9", QCOM_RPM_PM8921_LDO9, &pm8921_pldo, "vdd_l9_l11" },
+ { "l10", QCOM_RPM_PM8921_LDO10, &pm8921_pldo, "vdd_l10_l22" },
+ { "l11", QCOM_RPM_PM8921_LDO11, &pm8921_pldo, "vdd_l9_l11" },
+ { "l12", QCOM_RPM_PM8921_LDO12, &pm8921_nldo, "vdd_l1_l2_l12_l18" },
+ { "l14", QCOM_RPM_PM8921_LDO14, &pm8921_pldo, "vdd_l4_l14" },
+ { "l15", QCOM_RPM_PM8921_LDO15, &pm8921_pldo, "vdd_l3_l15_l17" },
+ { "l16", QCOM_RPM_PM8921_LDO16, &pm8921_pldo, "vdd_l5_l8_l16" },
+ { "l17", QCOM_RPM_PM8921_LDO17, &pm8921_pldo, "vdd_l3_l15_l17" },
+ { "l18", QCOM_RPM_PM8921_LDO18, &pm8921_nldo, "vdd_l1_l2_l12_l18" },
+ { "l21", QCOM_RPM_PM8921_LDO21, &pm8921_pldo, "vdd_l21_l23_l29" },
+ { "l22", QCOM_RPM_PM8921_LDO22, &pm8921_pldo, "vdd_l10_l22" },
+ { "l23", QCOM_RPM_PM8921_LDO23, &pm8921_pldo, "vdd_l21_l23_l29" },
+ { "l24", QCOM_RPM_PM8921_LDO24, &pm8921_nldo1200, "vdd_l24" },
+ { "l25", QCOM_RPM_PM8921_LDO25, &pm8921_nldo1200, "vdd_l25" },
+ { "l26", QCOM_RPM_PM8921_LDO26, &pm8921_nldo1200, "vdd_l26" },
+ { "l27", QCOM_RPM_PM8921_LDO27, &pm8921_nldo1200, "vdd_l27" },
+ { "l28", QCOM_RPM_PM8921_LDO28, &pm8921_nldo1200, "vdd_l28" },
+ { "l29", QCOM_RPM_PM8921_LDO29, &pm8921_pldo, "vdd_l21_l23_l29" },
+
+ { "lvs1", QCOM_RPM_PM8921_LVS1, &pm8921_switch, "vin_lvs1_3_6" },
+ { "lvs2", QCOM_RPM_PM8921_LVS2, &pm8921_switch, "vin_lvs2" },
+ { "lvs3", QCOM_RPM_PM8921_LVS3, &pm8921_switch, "vin_lvs1_3_6" },
+ { "lvs4", QCOM_RPM_PM8921_LVS4, &pm8921_switch, "vin_lvs4_5_7" },
+ { "lvs5", QCOM_RPM_PM8921_LVS5, &pm8921_switch, "vin_lvs4_5_7" },
+ { "lvs6", QCOM_RPM_PM8921_LVS6, &pm8921_switch, "vin_lvs1_3_6" },
+ { "lvs7", QCOM_RPM_PM8921_LVS7, &pm8921_switch, "vin_lvs4_5_7" },
+
+ { "usb-switch", QCOM_RPM_USB_OTG_SWITCH, &pm8921_switch, "vin_5vs" },
+ { "hdmi-switch", QCOM_RPM_HDMI_SWITCH, &pm8921_switch, "vin_5vs" },
+ { "ncp", QCOM_RPM_PM8921_NCP, &pm8921_ncp, "vdd_ncp" },
+ { }
+};
+static const struct of_device_id rpm_of_match[] = {
+ { .compatible = "qcom,rpm-pm8058-regulators", .data = &rpm_pm8058_regulators },
+ { .compatible = "qcom,rpm-pm8901-regulators", .data = &rpm_pm8901_regulators },
+ { .compatible = "qcom,rpm-pm8921-regulators", .data = &rpm_pm8921_regulators },
+ { }
+};
+MODULE_DEVICE_TABLE(of, rpm_of_match);
- config.dev = &pdev->dev;
- config.init_data = initdata;
- config.driver_data = vreg;
- config.of_node = pdev->dev.of_node;
+static int rpm_reg_probe(struct platform_device *pdev)
+{
+ const struct rpm_regulator_data *reg;
+ const struct of_device_id *match;
+ struct regulator_config config = { };
+ struct regulator_dev *rdev;
+ struct qcom_rpm_reg *vreg;
- ret = rpm_reg_of_parse(pdev->dev.of_node, &vreg->desc, &config);
- if (ret)
- return ret;
+ match = of_match_device(rpm_of_match, &pdev->dev);
+ for (reg = match->data; reg->name; reg++) {
+ vreg = devm_kmalloc(&pdev->dev, sizeof(*vreg), GFP_KERNEL);
+ if (!vreg) {
+ dev_err(&pdev->dev, "failed to allocate vreg\n");
+ return -ENOMEM;
+ }
+ memcpy(vreg, reg->template, sizeof(*vreg));
+ mutex_init(&vreg->lock);
+
+ vreg->dev = &pdev->dev;
+ vreg->resource = reg->resource;
+
+ vreg->desc.id = -1;
+ vreg->desc.owner = THIS_MODULE;
+ vreg->desc.type = REGULATOR_VOLTAGE;
+ vreg->desc.name = reg->name;
+ vreg->desc.supply_name = reg->supply;
+ vreg->desc.of_match = reg->name;
+ vreg->desc.of_parse_cb = rpm_reg_of_parse;
+
+ vreg->rpm = dev_get_drvdata(pdev->dev.parent);
+ if (!vreg->rpm) {
+ dev_err(&pdev->dev, "unable to retrieve handle to rpm\n");
+ return -ENODEV;
+ }
- rdev = devm_regulator_register(&pdev->dev, &vreg->desc, &config);
- if (IS_ERR(rdev)) {
- dev_err(&pdev->dev, "can't register regulator\n");
- return PTR_ERR(rdev);
+ config.dev = &pdev->dev;
+ config.driver_data = vreg;
+ rdev = devm_regulator_register(&pdev->dev, &vreg->desc, &config);
+ if (IS_ERR(rdev)) {
+ dev_err(&pdev->dev, "can't register regulator\n");
+ return PTR_ERR(rdev);
+ }
}
return 0;
--
1.8.2.2
Tidy up error reporting and move rpm reference retrieval out of the for
loop for improved readability.
Signed-off-by: Bjorn Andersson <[email protected]>
---
Patch added to series since v2.
drivers/regulator/qcom_rpm-regulator.c | 21 +++++++++++----------
1 file changed, 11 insertions(+), 10 deletions(-)
diff --git a/drivers/regulator/qcom_rpm-regulator.c b/drivers/regulator/qcom_rpm-regulator.c
index 40cf6ff..e254272 100644
--- a/drivers/regulator/qcom_rpm-regulator.c
+++ b/drivers/regulator/qcom_rpm-regulator.c
@@ -884,19 +884,26 @@ static int rpm_reg_probe(struct platform_device *pdev)
struct regulator_config config = { };
struct regulator_dev *rdev;
struct qcom_rpm_reg *vreg;
+ struct qcom_rpm *rpm;
+
+ rpm = dev_get_drvdata(pdev->dev.parent);
+ if (!rpm) {
+ dev_err(&pdev->dev, "unable to retrieve handle to rpm\n");
+ return -ENODEV;
+ }
match = of_match_device(rpm_of_match, &pdev->dev);
for (reg = match->data; reg->name; reg++) {
vreg = devm_kmalloc(&pdev->dev, sizeof(*vreg), GFP_KERNEL);
- if (!vreg) {
- dev_err(&pdev->dev, "failed to allocate vreg\n");
+ if (!vreg)
return -ENOMEM;
- }
+
memcpy(vreg, reg->template, sizeof(*vreg));
mutex_init(&vreg->lock);
vreg->dev = &pdev->dev;
vreg->resource = reg->resource;
+ vreg->rpm = rpm;
vreg->desc.id = -1;
vreg->desc.owner = THIS_MODULE;
@@ -906,17 +913,11 @@ static int rpm_reg_probe(struct platform_device *pdev)
vreg->desc.of_match = reg->name;
vreg->desc.of_parse_cb = rpm_reg_of_parse;
- vreg->rpm = dev_get_drvdata(pdev->dev.parent);
- if (!vreg->rpm) {
- dev_err(&pdev->dev, "unable to retrieve handle to rpm\n");
- return -ENODEV;
- }
-
config.dev = &pdev->dev;
config.driver_data = vreg;
rdev = devm_regulator_register(&pdev->dev, &vreg->desc, &config);
if (IS_ERR(rdev)) {
- dev_err(&pdev->dev, "can't register regulator\n");
+ dev_err(&pdev->dev, "failed to register %s\n", reg->name);
return PTR_ERR(rdev);
}
}
--
1.8.2.2
On 04/06/15 16:33, Bjorn Andersson wrote:
> Modeling the individual RPM resources as platform devices consumes at
> least 12-15kb of RAM, just to hold the platform_device structs. Rework
> this to instead have one device per pmic exposed by the RPM.
>
> With this representation we can more accurately define the input pins on
> the pmic and have the supply description match the data sheet.
>
> Suggested-by: Stephen Boyd <[email protected]>
> Signed-off-by: Bjorn Andersson <[email protected]>
> ---
Reviewed-by: Stephen Boyd <[email protected]>
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
On 04/06/15 16:34, Bjorn Andersson wrote:
> Tidy up error reporting and move rpm reference retrieval out of the for
> loop for improved readability.
>
> Signed-off-by: Bjorn Andersson <[email protected]>
> ---
>
Reviewed-by: Stephen Boyd <[email protected]>
Thanks.
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
On Mon, 06 Apr 2015, Bjorn Andersson wrote:
> Add the regulator subnodes to the Qualcomm RPM MFD device tree bindings.
>
> Reviewed-by: Stephen Boyd <[email protected]>
> Signed-off-by: Bjorn Andersson <[email protected]>
> ---
>
> Changes since v2:
> - s/notes/nodes from Stephen
>
> Documentation/devicetree/bindings/mfd/qcom-rpm.txt | 217 +++++++++++++++++++--
> 1 file changed, 205 insertions(+), 12 deletions(-)
Applied, thanks.
> diff --git a/Documentation/devicetree/bindings/mfd/qcom-rpm.txt b/Documentation/devicetree/bindings/mfd/qcom-rpm.txt
> index 85e3198..f7c22c5 100644
> --- a/Documentation/devicetree/bindings/mfd/qcom-rpm.txt
> +++ b/Documentation/devicetree/bindings/mfd/qcom-rpm.txt
> @@ -31,16 +31,6 @@ frequencies.
> Value type: <string-array>
> Definition: must be the three strings "ack", "err" and "wakeup", in order
>
> -- #address-cells:
> - Usage: required
> - Value type: <u32>
> - Definition: must be 1
> -
> -- #size-cells:
> - Usage: required
> - Value type: <u32>
> - Definition: must be 0
> -
> - qcom,ipc:
> Usage: required
> Value type: <prop-encoded-array>
> @@ -52,6 +42,188 @@ frequencies.
> - u32 representing the ipc bit within the register
>
>
> += SUBNODES
> +
> +The RPM exposes resources to its subnodes. The below bindings specify the set
> +of valid subnodes that can operate on these resources.
> +
> +== Regulators
> +
> +Regulator nodes are identified by their compatible:
> +
> +- compatible:
> + Usage: required
> + Value type: <string>
> + Definition: must be one of:
> + "qcom,rpm-pm8058-regulators"
> + "qcom,rpm-pm8901-regulators"
> + "qcom,rpm-pm8921-regulators"
> +
> +- vdd_l0_l1_lvs-supply:
> +- vdd_l2_l11_l12-supply:
> +- vdd_l3_l4_l5-supply:
> +- vdd_l6_l7-supply:
> +- vdd_l8-supply:
> +- vdd_l9-supply:
> +- vdd_l10-supply:
> +- vdd_l13_l16-supply:
> +- vdd_l14_l15-supply:
> +- vdd_l17_l18-supply:
> +- vdd_l19_l20-supply:
> +- vdd_l21-supply:
> +- vdd_l22-supply:
> +- vdd_l23_l24_l25-supply:
> +- vdd_ncp-supply:
> +- vdd_s0-supply:
> +- vdd_s1-supply:
> +- vdd_s2-supply:
> +- vdd_s3-supply:
> +- vdd_s4-supply:
> + Usage: optional (pm8058 only)
> + Value type: <phandle>
> + Definition: reference to regulator supplying the input pin, as
> + described in the data sheet
> +
> +- lvs0_in-supply:
> +- lvs1_in-supply:
> +- lvs2_in-supply:
> +- lvs3_in-supply:
> +- mvs_in-supply:
> +- vdd_l0-supply:
> +- vdd_l1-supply:
> +- vdd_l2-supply:
> +- vdd_l3-supply:
> +- vdd_l4-supply:
> +- vdd_l5-supply:
> +- vdd_l6-supply:
> +- vdd_s0-supply:
> +- vdd_s1-supply:
> +- vdd_s2-supply:
> +- vdd_s3-supply:
> +- vdd_s4-supply:
> + Usage: optional (pm8901 only)
> + Value type: <phandle>
> + Definition: reference to regulator supplying the input pin, as
> + described in the data sheet
> +
> +- vdd_l1_l2_l12_l18-supply:
> +- vdd_l3_l15_l17-supply:
> +- vdd_l4_l14-supply:
> +- vdd_l5_l8_l16-supply:
> +- vdd_l6_l7-supply:
> +- vdd_l9_l11-supply:
> +- vdd_l10_l22-supply:
> +- vdd_l21_l23_l29-supply:
> +- vdd_l24-supply:
> +- vdd_l25-supply:
> +- vdd_l26-supply:
> +- vdd_l27-supply:
> +- vdd_l28-supply:
> +- vdd_ncp-supply:
> +- vdd_s1-supply:
> +- vdd_s2-supply:
> +- vdd_s4-supply:
> +- vdd_s5-supply:
> +- vdd_s6-supply:
> +- vdd_s7-supply:
> +- vdd_s8-supply:
> +- vin_5vs-supply:
> +- vin_lvs1_3_6-supply:
> +- vin_lvs2-supply:
> +- vin_lvs4_5_7-supply:
> + Usage: optional (pm8921 only)
> + Value type: <phandle>
> + Definition: reference to regulator supplying the input pin, as
> + described in the data sheet
> +
> +The regulator node houses sub-nodes for each regulator within the device. Each
> +sub-node is identified using the node's name, with valid values listed for each
> +of the pmics below.
> +
> +pm8058:
> + l0, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, l14, l15,
> + l16, l17, l18, l19, l20, l21, l22, l23, l24, l25, s0, s1, s2, s3, s4,
> + lvs0, lvs1, ncp
> +
> +pm8901:
> + l0, l1, l2, l3, l4, l5, l6, s0, s1, s2, s3, s4, lvs0, lvs1, lvs2, lvs3,
> + mvs
> +
> +pm8921:
> + s1, s2, s3, s4, s7, s8, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11,
> + l12, l14, l15, l16, l17, l18, l21, l22, l23, l24, l25, l26, l27, l28,
> + l29, lvs1, lvs2, lvs3, lvs4, lvs5, lvs6, lvs7, usb-switch, hdmi-switch,
> + ncp
> +
> +The content of each sub-node is defined by the standard binding for regulators -
> +see regulator.txt - with additional custom properties described below:
> +
> +=== Switch-mode Power Supply regulator custom properties
> +
> +- bias-pull-down:
> + Usage: optional
> + Value type: <empty>
> + Definition: enable pull down of the regulator when inactive
> +
> +- qcom,switch-mode-frequency:
> + Usage: required
> + Value type: <u32>
> + Definition: Frequency (Hz) of the switch-mode power supply;
> + must be one of:
> + 19200000, 9600000, 6400000, 4800000, 3840000, 3200000,
> + 2740000, 2400000, 2130000, 1920000, 1750000, 1600000,
> + 1480000, 1370000, 1280000, 1200000
> +
> +- qcom,force-mode:
> + Usage: optional (default if no other qcom,force-mode is specified)
> + Value type: <u32>
> + Defintion: indicates that the regulator should be forced to a
> + particular mode, valid values are:
> + QCOM_RPM_FORCE_MODE_NONE - do not force any mode
> + QCOM_RPM_FORCE_MODE_LPM - force into low power mode
> + QCOM_RPM_FORCE_MODE_HPM - force into high power mode
> + QCOM_RPM_FORCE_MODE_AUTO - allow regulator to automatically
> + select its own mode based on
> + realtime current draw, only for:
> + pm8921 smps and ftsmps
> +
> +- qcom,power-mode-hysteretic:
> + Usage: optional
> + Value type: <empty>
> + Definition: select that the power supply should operate in hysteretic
> + mode, instead of the default pwm mode
> +
> +=== Low-dropout regulator custom properties
> +
> +- bias-pull-down:
> + Usage: optional
> + Value type: <empty>
> + Definition: enable pull down of the regulator when inactive
> +
> +- qcom,force-mode:
> + Usage: optional
> + Value type: <u32>
> + Defintion: indicates that the regulator should not be forced to any
> + particular mode, valid values are:
> + QCOM_RPM_FORCE_MODE_NONE - do not force any mode
> + QCOM_RPM_FORCE_MODE_LPM - force into low power mode
> + QCOM_RPM_FORCE_MODE_HPM - force into high power mode
> + QCOM_RPM_FORCE_MODE_BYPASS - set regulator to use bypass
> + mode, i.e. to act as a switch
> + and not regulate, only for:
> + pm8921 pldo, nldo and nldo1200
> +
> +=== Negative Charge Pump custom properties
> +
> +- qcom,switch-mode-frequency:
> + Usage: required
> + Value type: <u32>
> + Definition: Frequency (Hz) of the swith mode power supply;
> + must be one of:
> + 19200000, 9600000, 6400000, 4800000, 3840000, 3200000,
> + 2740000, 2400000, 2130000, 1920000, 1750000, 1600000,
> + 1480000, 1370000, 1280000, 1200000
> +
> = EXAMPLE
>
> #include <dt-bindings/mfd/qcom-rpm.h>
> @@ -64,7 +236,28 @@ frequencies.
> interrupts = <0 19 0>, <0 21 0>, <0 22 0>;
> interrupt-names = "ack", "err", "wakeup";
>
> - #address-cells = <1>;
> - #size-cells = <0>;
> + regulators {
> + compatible = "qcom,rpm-pm8921-regulators";
> + vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
> +
> + s1 {
> + regulator-min-microvolt = <1225000>;
> + regulator-max-microvolt = <1225000>;
> +
> + bias-pull-down;
> +
> + qcom,switch-mode-frequency = <3200000>;
> + };
> +
> + pm8921_s4: s4 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> +
> + qcom,switch-mode-frequency = <1600000>;
> + bias-pull-down;
> +
> + qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
> + };
> + };
> };
>
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
On Mon, Apr 06, 2015 at 04:33:57PM -0700, Bjorn Andersson wrote:
> The driver itself should not flag regulators as being DRMS compatible,
> this should come from board or dt files.
I'm missing patch 1, please check and resend.
On Tue, Apr 7, 2015 at 4:11 AM, Mark Brown <[email protected]> wrote:
> On Mon, Apr 06, 2015 at 04:33:57PM -0700, Bjorn Andersson wrote:
>> The driver itself should not flag regulators as being DRMS compatible,
>> this should come from board or dt files.
>
> I'm missing patch 1, please check and resend.
Looks like I forgot to add you as a recipient, sorry about that...
Lee answered earlier today that he applied the patch, as you can see here [1].
[1] https://patchwork.kernel.org/patch/6166461/
Regards,
Bjorn
On Mon, Apr 06, 2015 at 04:33:55PM -0700, Bjorn Andersson wrote:
> Stephen Boyd pointed out that the current design of the Qualcomm RPM and
> regulator driver consumes 12-20kB of ram just for the platform_device structs.
Applied the regulator patches, thanks.