The anx6345 driver originally was copied from anx78xx.c, which has meanwhile
seen a few changes. In particular, the removal of drm_dp_link helpers and the
discontinuation to include drm_bridge.h from drm_crtc.h breaks compilation
in linux-5.5. Apply equivalents of these changes to anx6345.c.
Signed-off-by: Torsten Duwe <[email protected]>
---
The commits in question are ff1e8fb68ea06 and ee68c743f8d07, but I guess the
next rebase will change these. next-20191112 plus the anx6345-v5a series plus
this patch compile cleanly on arm64.
--- a/drivers/gpu/drm/bridge/analogix/analogix-anx6345.c
+++ b/drivers/gpu/drm/bridge/analogix/analogix-anx6345.c
@@ -19,6 +19,7 @@
#include <linux/types.h>
#include <drm/drm_atomic_helper.h>
+#include <drm/drm_bridge.h>
#include <drm/drm_crtc.h>
#include <drm/drm_crtc_helper.h>
#include <drm/drm_dp_helper.h>
@@ -49,7 +50,6 @@ struct anx6345 {
struct i2c_client *client;
struct edid *edid;
struct drm_connector connector;
- struct drm_dp_link link;
struct drm_panel *panel;
struct regulator *dvdd12;
struct regulator *dvdd25;
@@ -96,7 +96,7 @@ static ssize_t anx6345_aux_transfer(stru
static int anx6345_dp_link_training(struct anx6345 *anx6345)
{
unsigned int value;
- u8 dp_bw;
+ u8 dp_bw, dpcd[2];
int err;
err = anx6345_clear_bits(anx6345->map[I2C_IDX_TXCOM],
@@ -144,18 +143,34 @@ static int anx6345_dp_link_training(stru
if (err)
return err;
- /* Check link capabilities */
- err = drm_dp_link_probe(&anx6345->aux, &anx6345->link);
- if (err < 0) {
- DRM_ERROR("Failed to probe link capabilities: %d\n", err);
- return err;
- }
+ /*
+ * Power up the sink (DP_SET_POWER register is only available on DPCD
+ * v1.1 and later).
+ */
+ if (anx6345->dpcd[DP_DPCD_REV] >= 0x11) {
+ err = drm_dp_dpcd_readb(&anx6345->aux, DP_SET_POWER, &dpcd[0]);
+ if (err < 0) {
+ DRM_ERROR("Failed to read DP_SET_POWER register: %d\n",
+ err);
+ return err;
+ }
+
+ dpcd[0] &= ~DP_SET_POWER_MASK;
+ dpcd[0] |= DP_SET_POWER_D0;
+
+ err = drm_dp_dpcd_writeb(&anx6345->aux, DP_SET_POWER, dpcd[0]);
+ if (err < 0) {
+ DRM_ERROR("Failed to power up DisplayPort link: %d\n",
+ err);
+ return err;
+ }
- /* Power up the sink */
- err = drm_dp_link_power_up(&anx6345->aux, &anx6345->link);
- if (err < 0) {
- DRM_ERROR("Failed to power up DisplayPort link: %d\n", err);
- return err;
+ /*
+ * According to the DP 1.1 specification, a "Sink Device must
+ * exit the power saving state within 1 ms" (Section 2.5.3.1,
+ * Table 5-52, "Sink Control Field" (register 0x600).
+ */
+ usleep_range(1000, 2000);
}
/* Possibly enable downspread on the sink */
@@ -194,20 +209,28 @@ static int anx6345_dp_link_training(stru
if (err)
return err;
- value = drm_dp_link_rate_to_bw_code(anx6345->link.rate);
+ dpcd[0] = drm_dp_max_link_rate(anx6345->dpcd);
+ dpcd[0] = drm_dp_link_rate_to_bw_code(dpcd[0]);
err = regmap_write(anx6345->map[I2C_IDX_DPTX],
- SP_DP_MAIN_LINK_BW_SET_REG, value);
+ SP_DP_MAIN_LINK_BW_SET_REG, dpcd[0]);
if (err)
return err;
+ dpcd[1] = drm_dp_max_lane_count(anx6345->dpcd);
+
err = regmap_write(anx6345->map[I2C_IDX_DPTX],
- SP_DP_LANE_COUNT_SET_REG, anx6345->link.num_lanes);
+ SP_DP_LANE_COUNT_SET_REG, dpcd[1]);
if (err)
return err;
- err = drm_dp_link_configure(&anx6345->aux, &anx6345->link);
+ if (drm_dp_enhanced_frame_cap(anx6345->dpcd))
+ dpcd[1] |= DP_LANE_COUNT_ENHANCED_FRAME_EN;
+
+ err = drm_dp_dpcd_write(&anx6345->aux, DP_LINK_BW_SET, dpcd,
+ sizeof(dpcd));
+
if (err < 0) {
- DRM_ERROR("Failed to configure DisplayPort link: %d\n", err);
+ DRM_ERROR("Failed to configure link: %d\n", err);
return err;
}
On Tue, Nov 12, 2019 at 6:59 PM Torsten Duwe <[email protected]> wrote:
>
>
> The anx6345 driver originally was copied from anx78xx.c, which has meanwhile
> seen a few changes. In particular, the removal of drm_dp_link helpers and the
> discontinuation to include drm_bridge.h from drm_crtc.h breaks compilation
> in linux-5.5. Apply equivalents of these changes to anx6345.c.
>
> Signed-off-by: Torsten Duwe <[email protected]>
Wait ... Maxime pushed this and it never compiled? What's going on here?
-Daniel
>
> ---
>
> The commits in question are ff1e8fb68ea06 and ee68c743f8d07, but I guess the
> next rebase will change these. next-20191112 plus the anx6345-v5a series plus
> this patch compile cleanly on arm64.
>
> --- a/drivers/gpu/drm/bridge/analogix/analogix-anx6345.c
> +++ b/drivers/gpu/drm/bridge/analogix/analogix-anx6345.c
> @@ -19,6 +19,7 @@
> #include <linux/types.h>
>
> #include <drm/drm_atomic_helper.h>
> +#include <drm/drm_bridge.h>
> #include <drm/drm_crtc.h>
> #include <drm/drm_crtc_helper.h>
> #include <drm/drm_dp_helper.h>
> @@ -49,7 +50,6 @@ struct anx6345 {
> struct i2c_client *client;
> struct edid *edid;
> struct drm_connector connector;
> - struct drm_dp_link link;
> struct drm_panel *panel;
> struct regulator *dvdd12;
> struct regulator *dvdd25;
> @@ -96,7 +96,7 @@ static ssize_t anx6345_aux_transfer(stru
> static int anx6345_dp_link_training(struct anx6345 *anx6345)
> {
> unsigned int value;
> - u8 dp_bw;
> + u8 dp_bw, dpcd[2];
> int err;
>
> err = anx6345_clear_bits(anx6345->map[I2C_IDX_TXCOM],
> @@ -144,18 +143,34 @@ static int anx6345_dp_link_training(stru
> if (err)
> return err;
>
> - /* Check link capabilities */
> - err = drm_dp_link_probe(&anx6345->aux, &anx6345->link);
> - if (err < 0) {
> - DRM_ERROR("Failed to probe link capabilities: %d\n", err);
> - return err;
> - }
> + /*
> + * Power up the sink (DP_SET_POWER register is only available on DPCD
> + * v1.1 and later).
> + */
> + if (anx6345->dpcd[DP_DPCD_REV] >= 0x11) {
> + err = drm_dp_dpcd_readb(&anx6345->aux, DP_SET_POWER, &dpcd[0]);
> + if (err < 0) {
> + DRM_ERROR("Failed to read DP_SET_POWER register: %d\n",
> + err);
> + return err;
> + }
> +
> + dpcd[0] &= ~DP_SET_POWER_MASK;
> + dpcd[0] |= DP_SET_POWER_D0;
> +
> + err = drm_dp_dpcd_writeb(&anx6345->aux, DP_SET_POWER, dpcd[0]);
> + if (err < 0) {
> + DRM_ERROR("Failed to power up DisplayPort link: %d\n",
> + err);
> + return err;
> + }
>
> - /* Power up the sink */
> - err = drm_dp_link_power_up(&anx6345->aux, &anx6345->link);
> - if (err < 0) {
> - DRM_ERROR("Failed to power up DisplayPort link: %d\n", err);
> - return err;
> + /*
> + * According to the DP 1.1 specification, a "Sink Device must
> + * exit the power saving state within 1 ms" (Section 2.5.3.1,
> + * Table 5-52, "Sink Control Field" (register 0x600).
> + */
> + usleep_range(1000, 2000);
> }
>
> /* Possibly enable downspread on the sink */
> @@ -194,20 +209,28 @@ static int anx6345_dp_link_training(stru
> if (err)
> return err;
>
> - value = drm_dp_link_rate_to_bw_code(anx6345->link.rate);
> + dpcd[0] = drm_dp_max_link_rate(anx6345->dpcd);
> + dpcd[0] = drm_dp_link_rate_to_bw_code(dpcd[0]);
> err = regmap_write(anx6345->map[I2C_IDX_DPTX],
> - SP_DP_MAIN_LINK_BW_SET_REG, value);
> + SP_DP_MAIN_LINK_BW_SET_REG, dpcd[0]);
> if (err)
> return err;
>
> + dpcd[1] = drm_dp_max_lane_count(anx6345->dpcd);
> +
> err = regmap_write(anx6345->map[I2C_IDX_DPTX],
> - SP_DP_LANE_COUNT_SET_REG, anx6345->link.num_lanes);
> + SP_DP_LANE_COUNT_SET_REG, dpcd[1]);
> if (err)
> return err;
>
> - err = drm_dp_link_configure(&anx6345->aux, &anx6345->link);
> + if (drm_dp_enhanced_frame_cap(anx6345->dpcd))
> + dpcd[1] |= DP_LANE_COUNT_ENHANCED_FRAME_EN;
> +
> + err = drm_dp_dpcd_write(&anx6345->aux, DP_LINK_BW_SET, dpcd,
> + sizeof(dpcd));
> +
> if (err < 0) {
> - DRM_ERROR("Failed to configure DisplayPort link: %d\n", err);
> + DRM_ERROR("Failed to configure link: %d\n", err);
> return err;
> }
>
--
Daniel Vetter
Software Engineer, Intel Corporation
+41 (0) 79 365 57 48 - http://blog.ffwll.ch
On Tue, Nov 12, 2019 at 06:59:40PM +0100, Torsten Duwe wrote:
>
> The anx6345 driver originally was copied from anx78xx.c, which has meanwhile
> seen a few changes. In particular, the removal of drm_dp_link helpers and the
> discontinuation to include drm_bridge.h from drm_crtc.h breaks compilation
> in linux-5.5. Apply equivalents of these changes to anx6345.c.
>
> Signed-off-by: Torsten Duwe <[email protected]>
>
> ---
I've pushed that fix, but it still doesn't compile on x86. I'm
guessing you're missing a depends on OF in the Kconfig option.
Maxime