We need to round up the values since the comparison in drm_mode_equal might fail if division
results in fractional part
Signed-off-by: Furquan Shaikh <[email protected]>
---
drivers/gpu/drm/i915/intel_display.c | 6 +++++-
1 file changed, 5 insertions(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
index 0f40f8e..e0069f4 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -7190,7 +7190,11 @@ static void ironlake_crtc_clock_get(struct intel_crtc *crtc,
return;
clock = ((u64)link_m * (u64)link_freq * (u64)repeat);
- do_div(clock, link_n);
+ /* This is required because the value comes out to be in fraction
+ (eg. 70699.54). Need to round it up since values are compared in
+ drm_mode_equal
+ */
+ clock = DIV_ROUND_UP_ULL(clock, link_n);
pipe_config->adjusted_mode.clock = clock;
}
--
1.8.3
Enables getting correct mode clock when reading pipe config
This patch has been tested successfully on top of drm-intel-nightly tree
Signed-off-by: Furquan Shaikh <[email protected]>
---
drivers/gpu/drm/i915/i915_reg.h | 6 ++++
drivers/gpu/drm/i915/intel_ddi.c | 70 ++++++++++++++++++++++++++++++++++++
drivers/gpu/drm/i915/intel_display.c | 1 +
3 files changed, 77 insertions(+)
diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h
index 2b96d6b..9511129 100644
--- a/drivers/gpu/drm/i915/i915_reg.h
+++ b/drivers/gpu/drm/i915/i915_reg.h
@@ -4970,6 +4970,7 @@
#define SPLL_PLL_NON_SSC (2<<28)
#define SPLL_PLL_FREQ_810MHz (0<<26)
#define SPLL_PLL_FREQ_1350MHz (1<<26)
+#define SPLL_PLL_FREQ_MASK (3<<26)
/* WRPLL */
#define WRPLL_CTL1 0x46040
@@ -4983,6 +4984,10 @@
#define WRPLL_DIVIDER_POST(x) ((x)<<8)
#define WRPLL_DIVIDER_FEEDBACK(x) ((x)<<16)
+#define WRPLL_DIVIDER_REFERENCE_BITS(reg) (reg & 0xff)
+#define WRPLL_DIVIDER_POST_BITS(reg) ((reg >> 8) & 0x3f)
+#define WRPLL_DIVIDER_FEEDBACK_BITS(reg) ((reg >> 16) & 0xff)
+
/* Port clock selection */
#define PORT_CLK_SEL_A 0x46100
#define PORT_CLK_SEL_B 0x46104
@@ -4994,6 +4999,7 @@
#define PORT_CLK_SEL_WRPLL1 (4<<29)
#define PORT_CLK_SEL_WRPLL2 (5<<29)
#define PORT_CLK_SEL_NONE (7<<29)
+#define PORT_CLK_SEL_MASK (7<<29)
/* Transcoder clock selection */
#define TRANS_CLK_SEL_A 0x46140
diff --git a/drivers/gpu/drm/i915/intel_ddi.c b/drivers/gpu/drm/i915/intel_ddi.c
index b8c096b..a24a375 100644
--- a/drivers/gpu/drm/i915/intel_ddi.c
+++ b/drivers/gpu/drm/i915/intel_ddi.c
@@ -1246,6 +1246,74 @@ static void intel_ddi_hot_plug(struct intel_encoder *intel_encoder)
intel_dp_check_link_status(intel_dp);
}
+static void intel_ddi_get_clock(struct intel_encoder *encoder,
+ struct intel_crtc_config *pipe_config)
+{
+ struct drm_i915_private *dev_priv = encoder->base.dev->dev_private;
+ int port = intel_ddi_get_encoder_port(encoder);
+ u32 temp = I915_READ(PORT_CLK_SEL(port)) & PORT_CLK_SEL_MASK;
+ u8 link_bw;
+
+ if ((temp == PORT_CLK_SEL_LCPLL_810) ||
+ (temp == PORT_CLK_SEL_LCPLL_1350) ||
+ (temp == PORT_CLK_SEL_LCPLL_2700)) {
+
+ switch (temp) {
+ case PORT_CLK_SEL_LCPLL_810:
+ link_bw = DP_LINK_BW_1_62;
+ break;
+ case PORT_CLK_SEL_LCPLL_1350:
+ link_bw = DP_LINK_BW_2_7;
+ break;
+ case PORT_CLK_SEL_LCPLL_2700:
+ link_bw = DP_LINK_BW_5_4;
+ break;
+ }
+ pipe_config->port_clock = drm_dp_bw_code_to_link_rate(link_bw);
+ } else if ((temp == PORT_CLK_SEL_WRPLL1) ||
+ (temp == PORT_CLK_SEL_WRPLL2)) {
+ uint64_t p, n2, r2;
+ u32 val, reg;
+ uint64_t freq2k;
+
+ switch (temp) {
+ case PORT_CLK_SEL_WRPLL1:
+ reg = WRPLL_CTL1;
+ break;
+ case PORT_CLK_SEL_WRPLL2:
+ reg = WRPLL_CTL2;
+ break;
+ }
+ val = I915_READ(reg);
+ r2 = WRPLL_DIVIDER_REFERENCE_BITS(val);
+ p = WRPLL_DIVIDER_POST_BITS(val);
+ n2 = WRPLL_DIVIDER_FEEDBACK_BITS(val);
+
+ freq2k = DIV_ROUND_UP_ULL(LC_FREQ * n2, r2 * p);
+ pipe_config->port_clock = freq2k / 10;
+ } else if (temp == PORT_CLK_SEL_SPLL) {
+ u32 val;
+
+ val = I915_READ(PORT_CLK_SEL_SPLL);
+
+ switch (val & SPLL_PLL_FREQ_MASK) {
+ case SPLL_PLL_FREQ_810MHz:
+ pipe_config->port_clock = 810000;
+ break;
+ case SPLL_PLL_FREQ_1350MHz:
+ pipe_config->port_clock = 1350000;
+ break;
+ default:
+ WARN(1, "Invalid pll freq %d\n",
+ val & SPLL_PLL_FREQ_MASK);
+ return;
+ }
+ } else {
+ WARN(1, "Invalid clock selection %d\n", temp);
+ return;
+ }
+}
+
static void intel_ddi_get_config(struct intel_encoder *encoder,
struct intel_crtc_config *pipe_config)
{
@@ -1265,6 +1333,8 @@ static void intel_ddi_get_config(struct intel_encoder *encoder,
flags |= DRM_MODE_FLAG_NVSYNC;
pipe_config->adjusted_mode.flags |= flags;
+
+ intel_ddi_get_clock(encoder, pipe_config);
}
static void intel_ddi_destroy(struct drm_encoder *encoder)
diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
index e0069f4..1c6a3d2 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -9579,6 +9579,7 @@ static void intel_init_display(struct drm_device *dev)
if (HAS_DDI(dev)) {
dev_priv->display.get_pipe_config = haswell_get_pipe_config;
+ dev_priv->display.get_clock = ironlake_crtc_clock_get;
dev_priv->display.crtc_mode_set = haswell_crtc_mode_set;
dev_priv->display.crtc_enable = haswell_crtc_enable;
dev_priv->display.crtc_disable = haswell_crtc_disable;
--
1.8.3
On Tue, Aug 20, 2013 at 3:33 AM, Furquan Shaikh <[email protected]> wrote:
> Enables getting correct mode clock when reading pipe config
> This patch has been tested successfully on top of drm-intel-nightly tree
>
> Signed-off-by: Furquan Shaikh <[email protected]>
This is missing a hunk to enable the pipe_config consistency checks:
diff --git a/drivers/gpu/drm/i915/intel_display.c
b/drivers/gpu/drm/i915/intel_display.c
index 7a40427..e8b73ac 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -8416,13 +8416,11 @@ intel_pipe_config_compare(struct drm_device *dev,
#undef PIPE_CONF_CHECK_FLAGS
#undef PIPE_CONF_QUIRK
- if (!IS_HASWELL(dev)) {
- if (!intel_fuzzy_clock_check(current_config, pipe_config)) {
- DRM_ERROR("mismatch in clock (expected %d, found %d)\n",
- current_config->adjusted_mode.clock,
- pipe_config->adjusted_mode.clock);
- return false;
- }
+ if (!intel_fuzzy_clock_check(current_config, pipe_config)) {
+ DRM_ERROR("mismatch in clock (expected %d, found %d)\n",
+ current_config->adjusted_mode.clock,
+ pipe_config->adjusted_mode.clock);
+ return false;
}
return true;
Cheers, Daniel
> ---
> drivers/gpu/drm/i915/i915_reg.h | 6 ++++
> drivers/gpu/drm/i915/intel_ddi.c | 70 ++++++++++++++++++++++++++++++++++++
> drivers/gpu/drm/i915/intel_display.c | 1 +
> 3 files changed, 77 insertions(+)
>
> diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h
> index 2b96d6b..9511129 100644
> --- a/drivers/gpu/drm/i915/i915_reg.h
> +++ b/drivers/gpu/drm/i915/i915_reg.h
> @@ -4970,6 +4970,7 @@
> #define SPLL_PLL_NON_SSC (2<<28)
> #define SPLL_PLL_FREQ_810MHz (0<<26)
> #define SPLL_PLL_FREQ_1350MHz (1<<26)
> +#define SPLL_PLL_FREQ_MASK (3<<26)
>
> /* WRPLL */
> #define WRPLL_CTL1 0x46040
> @@ -4983,6 +4984,10 @@
> #define WRPLL_DIVIDER_POST(x) ((x)<<8)
> #define WRPLL_DIVIDER_FEEDBACK(x) ((x)<<16)
>
> +#define WRPLL_DIVIDER_REFERENCE_BITS(reg) (reg & 0xff)
> +#define WRPLL_DIVIDER_POST_BITS(reg) ((reg >> 8) & 0x3f)
> +#define WRPLL_DIVIDER_FEEDBACK_BITS(reg) ((reg >> 16) & 0xff)
> +
> /* Port clock selection */
> #define PORT_CLK_SEL_A 0x46100
> #define PORT_CLK_SEL_B 0x46104
> @@ -4994,6 +4999,7 @@
> #define PORT_CLK_SEL_WRPLL1 (4<<29)
> #define PORT_CLK_SEL_WRPLL2 (5<<29)
> #define PORT_CLK_SEL_NONE (7<<29)
> +#define PORT_CLK_SEL_MASK (7<<29)
>
> /* Transcoder clock selection */
> #define TRANS_CLK_SEL_A 0x46140
> diff --git a/drivers/gpu/drm/i915/intel_ddi.c b/drivers/gpu/drm/i915/intel_ddi.c
> index b8c096b..a24a375 100644
> --- a/drivers/gpu/drm/i915/intel_ddi.c
> +++ b/drivers/gpu/drm/i915/intel_ddi.c
> @@ -1246,6 +1246,74 @@ static void intel_ddi_hot_plug(struct intel_encoder *intel_encoder)
> intel_dp_check_link_status(intel_dp);
> }
>
> +static void intel_ddi_get_clock(struct intel_encoder *encoder,
> + struct intel_crtc_config *pipe_config)
> +{
> + struct drm_i915_private *dev_priv = encoder->base.dev->dev_private;
> + int port = intel_ddi_get_encoder_port(encoder);
> + u32 temp = I915_READ(PORT_CLK_SEL(port)) & PORT_CLK_SEL_MASK;
> + u8 link_bw;
> +
> + if ((temp == PORT_CLK_SEL_LCPLL_810) ||
> + (temp == PORT_CLK_SEL_LCPLL_1350) ||
> + (temp == PORT_CLK_SEL_LCPLL_2700)) {
> +
> + switch (temp) {
> + case PORT_CLK_SEL_LCPLL_810:
> + link_bw = DP_LINK_BW_1_62;
> + break;
> + case PORT_CLK_SEL_LCPLL_1350:
> + link_bw = DP_LINK_BW_2_7;
> + break;
> + case PORT_CLK_SEL_LCPLL_2700:
> + link_bw = DP_LINK_BW_5_4;
> + break;
> + }
> + pipe_config->port_clock = drm_dp_bw_code_to_link_rate(link_bw);
> + } else if ((temp == PORT_CLK_SEL_WRPLL1) ||
> + (temp == PORT_CLK_SEL_WRPLL2)) {
> + uint64_t p, n2, r2;
> + u32 val, reg;
> + uint64_t freq2k;
> +
> + switch (temp) {
> + case PORT_CLK_SEL_WRPLL1:
> + reg = WRPLL_CTL1;
> + break;
> + case PORT_CLK_SEL_WRPLL2:
> + reg = WRPLL_CTL2;
> + break;
> + }
> + val = I915_READ(reg);
> + r2 = WRPLL_DIVIDER_REFERENCE_BITS(val);
> + p = WRPLL_DIVIDER_POST_BITS(val);
> + n2 = WRPLL_DIVIDER_FEEDBACK_BITS(val);
> +
> + freq2k = DIV_ROUND_UP_ULL(LC_FREQ * n2, r2 * p);
> + pipe_config->port_clock = freq2k / 10;
> + } else if (temp == PORT_CLK_SEL_SPLL) {
> + u32 val;
> +
> + val = I915_READ(PORT_CLK_SEL_SPLL);
> +
> + switch (val & SPLL_PLL_FREQ_MASK) {
> + case SPLL_PLL_FREQ_810MHz:
> + pipe_config->port_clock = 810000;
> + break;
> + case SPLL_PLL_FREQ_1350MHz:
> + pipe_config->port_clock = 1350000;
> + break;
> + default:
> + WARN(1, "Invalid pll freq %d\n",
> + val & SPLL_PLL_FREQ_MASK);
> + return;
> + }
> + } else {
> + WARN(1, "Invalid clock selection %d\n", temp);
> + return;
> + }
> +}
> +
> static void intel_ddi_get_config(struct intel_encoder *encoder,
> struct intel_crtc_config *pipe_config)
> {
> @@ -1265,6 +1333,8 @@ static void intel_ddi_get_config(struct intel_encoder *encoder,
> flags |= DRM_MODE_FLAG_NVSYNC;
>
> pipe_config->adjusted_mode.flags |= flags;
> +
> + intel_ddi_get_clock(encoder, pipe_config);
> }
>
> static void intel_ddi_destroy(struct drm_encoder *encoder)
> diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
> index e0069f4..1c6a3d2 100644
> --- a/drivers/gpu/drm/i915/intel_display.c
> +++ b/drivers/gpu/drm/i915/intel_display.c
> @@ -9579,6 +9579,7 @@ static void intel_init_display(struct drm_device *dev)
>
> if (HAS_DDI(dev)) {
> dev_priv->display.get_pipe_config = haswell_get_pipe_config;
> + dev_priv->display.get_clock = ironlake_crtc_clock_get;
> dev_priv->display.crtc_mode_set = haswell_crtc_mode_set;
> dev_priv->display.crtc_enable = haswell_crtc_enable;
> dev_priv->display.crtc_disable = haswell_crtc_disable;
> --
> 1.8.3
>
> _______________________________________________
> dri-devel mailing list
> [email protected]
> http://lists.freedesktop.org/mailman/listinfo/dri-devel
--
Daniel Vetter
Software Engineer, Intel Corporation
+41 (0) 79 365 57 48 - http://blog.ffwll.ch
Hi
2013/8/19 Furquan Shaikh <[email protected]>:
> Enables getting correct mode clock when reading pipe config
> This patch has been tested successfully on top of drm-intel-nightly tree
>
> Signed-off-by: Furquan Shaikh <[email protected]>
> ---
> drivers/gpu/drm/i915/i915_reg.h | 6 ++++
> drivers/gpu/drm/i915/intel_ddi.c | 70 ++++++++++++++++++++++++++++++++++++
> drivers/gpu/drm/i915/intel_display.c | 1 +
> 3 files changed, 77 insertions(+)
>
> diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h
> index 2b96d6b..9511129 100644
> --- a/drivers/gpu/drm/i915/i915_reg.h
> +++ b/drivers/gpu/drm/i915/i915_reg.h
> @@ -4970,6 +4970,7 @@
> #define SPLL_PLL_NON_SSC (2<<28)
> #define SPLL_PLL_FREQ_810MHz (0<<26)
> #define SPLL_PLL_FREQ_1350MHz (1<<26)
> +#define SPLL_PLL_FREQ_MASK (3<<26)
>
> /* WRPLL */
> #define WRPLL_CTL1 0x46040
> @@ -4983,6 +4984,10 @@
> #define WRPLL_DIVIDER_POST(x) ((x)<<8)
> #define WRPLL_DIVIDER_FEEDBACK(x) ((x)<<16)
>
> +#define WRPLL_DIVIDER_REFERENCE_BITS(reg) (reg & 0xff)
> +#define WRPLL_DIVIDER_POST_BITS(reg) ((reg >> 8) & 0x3f)
> +#define WRPLL_DIVIDER_FEEDBACK_BITS(reg) ((reg >> 16) & 0xff)
> +
> /* Port clock selection */
> #define PORT_CLK_SEL_A 0x46100
> #define PORT_CLK_SEL_B 0x46104
> @@ -4994,6 +4999,7 @@
> #define PORT_CLK_SEL_WRPLL1 (4<<29)
> #define PORT_CLK_SEL_WRPLL2 (5<<29)
> #define PORT_CLK_SEL_NONE (7<<29)
> +#define PORT_CLK_SEL_MASK (7<<29)
>
> /* Transcoder clock selection */
> #define TRANS_CLK_SEL_A 0x46140
> diff --git a/drivers/gpu/drm/i915/intel_ddi.c b/drivers/gpu/drm/i915/intel_ddi.c
> index b8c096b..a24a375 100644
> --- a/drivers/gpu/drm/i915/intel_ddi.c
> +++ b/drivers/gpu/drm/i915/intel_ddi.c
> @@ -1246,6 +1246,74 @@ static void intel_ddi_hot_plug(struct intel_encoder *intel_encoder)
> intel_dp_check_link_status(intel_dp);
> }
>
> +static void intel_ddi_get_clock(struct intel_encoder *encoder,
> + struct intel_crtc_config *pipe_config)
> +{
> + struct drm_i915_private *dev_priv = encoder->base.dev->dev_private;
> + int port = intel_ddi_get_encoder_port(encoder);
> + u32 temp = I915_READ(PORT_CLK_SEL(port)) & PORT_CLK_SEL_MASK;
> + u8 link_bw;
> +
> + if ((temp == PORT_CLK_SEL_LCPLL_810) ||
> + (temp == PORT_CLK_SEL_LCPLL_1350) ||
> + (temp == PORT_CLK_SEL_LCPLL_2700)) {
> +
> + switch (temp) {
> + case PORT_CLK_SEL_LCPLL_810:
> + link_bw = DP_LINK_BW_1_62;
> + break;
> + case PORT_CLK_SEL_LCPLL_1350:
> + link_bw = DP_LINK_BW_2_7;
> + break;
> + case PORT_CLK_SEL_LCPLL_2700:
> + link_bw = DP_LINK_BW_5_4;
> + break;
> + }
> + pipe_config->port_clock = drm_dp_bw_code_to_link_rate(link_bw);
drivers/gpu/drm/i915/intel_ddi.c:1275:56: aviso: ?link_bw? may be used
uninitialized in this function [-Wmaybe-uninitialized]
Looks like gcc 4.7.3 isn't that smart :( You should probably add a
"default" case with a WARN_ON(1) inside it.
> + } else if ((temp == PORT_CLK_SEL_WRPLL1) ||
> + (temp == PORT_CLK_SEL_WRPLL2)) {
> + uint64_t p, n2, r2;
> + u32 val, reg;
> + uint64_t freq2k;
> +
> + switch (temp) {
> + case PORT_CLK_SEL_WRPLL1:
> + reg = WRPLL_CTL1;
> + break;
> + case PORT_CLK_SEL_WRPLL2:
> + reg = WRPLL_CTL2;
> + break;
> + }
> + val = I915_READ(reg);
drivers/gpu/drm/i915/intel_ddi.c:1290:7: aviso: ?reg? may be used
uninitialized in this function [-Wmaybe-uninitialized]
Same thing here.
> + r2 = WRPLL_DIVIDER_REFERENCE_BITS(val);
> + p = WRPLL_DIVIDER_POST_BITS(val);
> + n2 = WRPLL_DIVIDER_FEEDBACK_BITS(val);
> +
> + freq2k = DIV_ROUND_UP_ULL(LC_FREQ * n2, r2 * p);
> + pipe_config->port_clock = freq2k / 10;
If you put the "/ 10" on the line above so it becomes
DIV_ROUND_UP_ULL(LC_FREQ * n2, r2 * p * 10) you'll avoid the rounding
errors of 1 division.
By the way, I applied your patch + Daniel's suggestion on -nightly and
now I see "unclaimed register" errors when booting with HDMI + eDP.
The problem is that we try to read disabled LINK_M/LINK_N registers
due to the power well disabled, so we get the error messages. I also
once saw a "pipe state mismatch" error, but I can't find a way to
reproduce it now. I'm also not sure whether VGA will really work since
we don't touch intel_crt.c (I can't test it for now). When testing the
patches, please always check dmesg for errors or warns, we should have
none. It looks to me that enabling fastboot on Haswell won't be so
simple due to these error messages I'm seeing. You should probably
convince Jesse to fix these problems :)
Thanks for the patches,
Paulo
> + } else if (temp == PORT_CLK_SEL_SPLL) {
> + u32 val;
> +
> + val = I915_READ(PORT_CLK_SEL_SPLL);
> +
> + switch (val & SPLL_PLL_FREQ_MASK) {
> + case SPLL_PLL_FREQ_810MHz:
> + pipe_config->port_clock = 810000;
> + break;
> + case SPLL_PLL_FREQ_1350MHz:
> + pipe_config->port_clock = 1350000;
> + break;
> + default:
> + WARN(1, "Invalid pll freq %d\n",
> + val & SPLL_PLL_FREQ_MASK);
> + return;
> + }
> + } else {
> + WARN(1, "Invalid clock selection %d\n", temp);
> + return;
> + }
> +}
> +
> static void intel_ddi_get_config(struct intel_encoder *encoder,
> struct intel_crtc_config *pipe_config)
> {
> @@ -1265,6 +1333,8 @@ static void intel_ddi_get_config(struct intel_encoder *encoder,
> flags |= DRM_MODE_FLAG_NVSYNC;
>
> pipe_config->adjusted_mode.flags |= flags;
> +
> + intel_ddi_get_clock(encoder, pipe_config);
> }
>
> static void intel_ddi_destroy(struct drm_encoder *encoder)
> diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
> index e0069f4..1c6a3d2 100644
> --- a/drivers/gpu/drm/i915/intel_display.c
> +++ b/drivers/gpu/drm/i915/intel_display.c
> @@ -9579,6 +9579,7 @@ static void intel_init_display(struct drm_device *dev)
>
> if (HAS_DDI(dev)) {
> dev_priv->display.get_pipe_config = haswell_get_pipe_config;
> + dev_priv->display.get_clock = ironlake_crtc_clock_get;
> dev_priv->display.crtc_mode_set = haswell_crtc_mode_set;
> dev_priv->display.crtc_enable = haswell_crtc_enable;
> dev_priv->display.crtc_disable = haswell_crtc_disable;
> --
> 1.8.3
>
> _______________________________________________
> dri-devel mailing list
> [email protected]
> http://lists.freedesktop.org/mailman/listinfo/dri-devel
--
Paulo Zanoni