LinuxLists.cc - [PATCH v1 0/2] Introduced new Cadence USBSS DRD Driver.

[permalink] [raw]

Subject: [PATCH v1 1/2] dt-bindings: add binding for USBSS-DRD controller.

This patch aim at documenting USB related dt-bindings for the
Cadence USBSS-DRD controller.

Signed-off-by: Pawel Laszczak <[email protected]>
---
.../devicetree/bindings/usb/cdns3-usb.txt | 31 +++++++++++++++++++
1 file changed, 31 insertions(+)
create mode 100644 Documentation/devicetree/bindings/usb/cdns3-usb.txt

diff --git a/Documentation/devicetree/bindings/usb/cdns3-usb.txt b/Documentation/devicetree/bindings/usb/cdns3-usb.txt
new file mode 100644
index 000000000000..ae4a255f0b10
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/cdns3-usb.txt
@@ -0,0 +1,31 @@
+Binding for the Cadence USBSS-DRD controller
+
+Required properties:
+ - reg: Physical base address and size of the controller's register areas.
+ Controller has 3 different regions:
+ region 1 - HOST registers area
+ region 2 - DEVICE registers area
+ region 3 - OTG/DRD registers area
+ - compatible: Should contain: "cdns,usb3"
+ - interrupts: Interrupt specifier. Refer to interrupt bindings.
+ Driver supports only single interrupt line.
+ This single interrupt is shared between Device,
+ host and OTG/DRD part of driver.
+
+Optional propertiesi:
+ - maximum-speed : valid arguments are "super-speed", "high-speed" and
+ "full-speed"; refer to usb/generic.txt
+ - dr_mode: Should be one of "host", "peripheral" or "otg".
+ - phys: reference to the USB PHY
+ - phy-names: name of the USB PHY, should be "cdns3,usbphy"
+
+
+Example:
+ usb@f3000000 {
+ compatible = "cdns,usb3";
+ interrupts = <USB_IRQ 7 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0xf3000000 0x10000 //memory area for HOST registers
+ 0xf3010000 0x10000 //memory area for DEVICE registers
+ 0xf3020000 0x10000>; //memory area for OTG/DRD registers
+ };
+
--
2.17.1

2018-12-10 12:55:17

[permalink] [raw]

Subject: [PATCH v1 2/2] usb:cdns3 Add Cadence USB3 DRD Driver

This patch introduce new Cadence USBSS DRD driver
to linux kernel.

The Cadence USBSS DRD Driver is a highly
configurable IP Core which can be
instantiated as Dual-Role Device (DRD),
Peripheral Only and Host Only (XHCI)
configurations.

The current driver has been validated with
FPGA burned. We have support for PCIe
bus, which is used on FPGA prototyping.

The host side of USBSS-DRD controller is compliance
with XHCI specification, so it works with
standard XHCI linux driver.

Signed-off-by: Pawel Laszczak <[email protected]>
---
drivers/usb/Kconfig | 2 +
drivers/usb/Makefile | 2 +
drivers/usb/cdns3/Kconfig | 44 +
drivers/usb/cdns3/Makefile | 16 +
drivers/usb/cdns3/cdns3-pci-wrap.c | 157 +++
drivers/usb/cdns3/core.c | 451 +++++++
drivers/usb/cdns3/core.h | 108 ++
drivers/usb/cdns3/debug.h | 346 ++++++
drivers/usb/cdns3/debugfs.c | 168 +++
drivers/usb/cdns3/drd.c | 315 +++++
drivers/usb/cdns3/drd.h | 129 ++
drivers/usb/cdns3/ep0.c | 864 +++++++++++++
drivers/usb/cdns3/gadget-export.h | 28 +
drivers/usb/cdns3/gadget.c | 1802 ++++++++++++++++++++++++++++
drivers/usb/cdns3/gadget.h | 1177 ++++++++++++++++++
drivers/usb/cdns3/host-export.h | 28 +
drivers/usb/cdns3/host.c | 74 ++
drivers/usb/cdns3/trace.c | 11 +
drivers/usb/cdns3/trace.h | 343 ++++++
19 files changed, 6065 insertions(+)
create mode 100644 drivers/usb/cdns3/Kconfig
create mode 100644 drivers/usb/cdns3/Makefile
create mode 100644 drivers/usb/cdns3/cdns3-pci-wrap.c
create mode 100644 drivers/usb/cdns3/core.c
create mode 100644 drivers/usb/cdns3/core.h
create mode 100644 drivers/usb/cdns3/debug.h
create mode 100644 drivers/usb/cdns3/debugfs.c
create mode 100644 drivers/usb/cdns3/drd.c
create mode 100644 drivers/usb/cdns3/drd.h
create mode 100644 drivers/usb/cdns3/ep0.c
create mode 100644 drivers/usb/cdns3/gadget-export.h
create mode 100644 drivers/usb/cdns3/gadget.c
create mode 100644 drivers/usb/cdns3/gadget.h
create mode 100644 drivers/usb/cdns3/host-export.h
create mode 100644 drivers/usb/cdns3/host.c
create mode 100644 drivers/usb/cdns3/trace.c
create mode 100644 drivers/usb/cdns3/trace.h

diff --git a/drivers/usb/Kconfig b/drivers/usb/Kconfig
index 987fc5ba6321..5f9334019d04 100644
--- a/drivers/usb/Kconfig
+++ b/drivers/usb/Kconfig
@@ -112,6 +112,8 @@ source "drivers/usb/usbip/Kconfig"

endif

+source "drivers/usb/cdns3/Kconfig"
+
source "drivers/usb/mtu3/Kconfig"

source "drivers/usb/musb/Kconfig"
diff --git a/drivers/usb/Makefile b/drivers/usb/Makefile
index 7d1b8c82b208..ab125b966cac 100644
--- a/drivers/usb/Makefile
+++ b/drivers/usb/Makefile
@@ -12,6 +12,8 @@ obj-$(CONFIG_USB_DWC3) += dwc3/
obj-$(CONFIG_USB_DWC2) += dwc2/
obj-$(CONFIG_USB_ISP1760) += isp1760/

+obj-$(CONFIG_USB_CDNS3) += cdns3/
+
obj-$(CONFIG_USB_MON) += mon/
obj-$(CONFIG_USB_MTU3) += mtu3/

diff --git a/drivers/usb/cdns3/Kconfig b/drivers/usb/cdns3/Kconfig
new file mode 100644
index 000000000000..4adfd87811e8
--- /dev/null
+++ b/drivers/usb/cdns3/Kconfig
@@ -0,0 +1,44 @@
+config USB_CDNS3
+ tristate "Cadence USB3 Dual-Role Controller"
+ depends on USB_SUPPORT && (USB || USB_GADGET) && HAS_DMA
+ help
+ Say Y here if your system has a cadence USB3 dual-role controller.
+ It supports: dual-role switch, Host-only, and Peripheral-only.
+
+ If you choose to build this driver is a dynamically linked
+ module, the module will be called cdns3.ko.
+
+if USB_CDNS3
+
+config USB_CDNS3_GADGET
+ bool "Cadence USB3 device controller"
+ depends on USB_GADGET
+ help
+ Say Y here to enable device controller functionality of the
+ cadence USBSS-DEV driver.
+
+ This controller supports FF, HS and SS mode. It doesn't support
+ LS and SSP mode
+
+config USB_CDNS3_HOST
+ bool "Cadence USB3 host controller"
+ depends on USB_XHCI_HCD
+ help
+ Say Y here to enable host controller functionality of the
+ cadence driver.
+
+ Host controller is compliance with XHCI so it will use
+ standard XHCI driver.
+
+config USB_CDNS3_PCI_WRAP
+ tristate "Cadence USB3 support on PCIe-based platforms"
+ depends on USB_PCI && ACPI
+ default USB_CDNS3
+ help
+ If you're using the USBSS Core IP with a PCIe, please say
+ 'Y' or 'M' here.
+
+ If you choose to build this driver as module it will
+ be dynamically linked and module will be called cdns3-pci.ko
+
+endif
diff --git a/drivers/usb/cdns3/Makefile b/drivers/usb/cdns3/Makefile
new file mode 100644
index 000000000000..3f63baa24294
--- /dev/null
+++ b/drivers/usb/cdns3/Makefile
@@ -0,0 +1,16 @@
+# SPDX-License-Identifier: GPL-2.0
+# define_trace.h needs to know how to find our header
+CFLAGS_trace.o := -I$(src)
+
+obj-$(CONFIG_USB_CDNS3) += cdns3.o
+obj-$(CONFIG_USB_CDNS3_PCI_WRAP) += cdns3-pci.o
+
+cdns3-y := core.o drd.o trace.o
+
+ifneq ($(CONFIG_DEBUG_FS),)
+ cdns3-y += debugfs.o
+endif
+
+cdns3-$(CONFIG_USB_CDNS3_GADGET) += gadget.o ep0.o
+cdns3-$(CONFIG_USB_CDNS3_HOST) += host.o
+cdns3-pci-y := cdns3-pci-wrap.o
diff --git a/drivers/usb/cdns3/cdns3-pci-wrap.c b/drivers/usb/cdns3/cdns3-pci-wrap.c
new file mode 100644
index 000000000000..e93179c45ece
--- /dev/null
+++ b/drivers/usb/cdns3/cdns3-pci-wrap.c
@@ -0,0 +1,157 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Cadence USBSS PCI Glue driver
+ *
+ * Copyright (C) 2018 Cadence.
+ *
+ * Author: Pawel Laszczak <[email protected]>
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/platform_device.h>
+#include <linux/dma-mapping.h>
+#include <linux/slab.h>
+
+struct cdns3_wrap {
+ struct platform_device *plat_dev;
+ struct pci_dev *hg_dev;
+ struct resource dev_res[4];
+};
+
+struct cdns3_wrap wrap;
+
+#define RES_IRQ_ID 0
+#define RES_HOST_ID 1
+#define RES_DEV_ID 2
+#define RES_DRD_ID 3
+
+#define PCI_BAR_HOST 0
+#define PCI_BAR_DEV 2
+#define PCI_BAR_OTG 4
+
+#define PCI_DEV_FN_HOST_DEVICE 0
+#define PCI_DEV_FN_OTG 1
+
+#define PCI_DRIVER_NAME "cdns3-pci-usbss"
+#define PLAT_DRIVER_NAME "cdns-usb3"
+
+#define CDNS_VENDOR_ID 0x17cd
+#define CDNS_DEVICE_ID 0x0100
+
+/**
+ * cdns3_pci_probe - Probe function for Cadence USB wrapper driver
+ * @pdev: platform device object
+ * @id: pci device id
+ *
+ * Returns 0 on success otherwise negative errno
+ */
+static int cdns3_pci_probe(struct pci_dev *pdev,
+ const struct pci_device_id *id)
+{
+ struct platform_device_info plat_info;
+ struct cdns3_wrap *wrap;
+ struct resource *res;
+ int err;
+
+ /*
+ * for GADGET/HOST PCI (devfn) function number is 0,
+ * for OTG PCI (devfn) function number is 1
+ */
+ if (!id || pdev->devfn != PCI_DEV_FN_HOST_DEVICE)
+ return -EINVAL;
+
+ err = pcim_enable_device(pdev);
+ if (err) {
+ dev_err(&pdev->dev, "Enabling PCI device has failed %d\n", err);
+ return err;
+ }
+
+ pci_set_master(pdev);
+ wrap = devm_kzalloc(&pdev->dev, sizeof(*wrap), GFP_KERNEL);
+ if (!wrap) {
+ dev_err(&pdev->dev, "Failed to allocate memory\n");
+ return -ENOMEM;
+ }
+
+ /* function 0: host(BAR_0) + device(BAR_1) + otg(BAR_2)). */
+ memset(wrap->dev_res, 0x00,
+ sizeof(struct resource) * ARRAY_SIZE(wrap->dev_res));
+ dev_dbg(&pdev->dev, "Initialize Device resources\n");
+ res = wrap->dev_res;
+
+ res[RES_DEV_ID].start = pci_resource_start(pdev, PCI_BAR_DEV);
+ res[RES_DEV_ID].end = pci_resource_end(pdev, PCI_BAR_DEV);
+ res[RES_DEV_ID].name = "cdns3-dev-regs";
+ res[RES_DEV_ID].flags = IORESOURCE_MEM;
+ dev_dbg(&pdev->dev, "USBSS-DEV physical base addr: %pa\n",
+ &res[RES_DEV_ID].start);
+
+ res[RES_HOST_ID].start = pci_resource_start(pdev, PCI_BAR_HOST);
+ res[RES_HOST_ID].end = pci_resource_end(pdev, PCI_BAR_HOST);
+ res[RES_HOST_ID].name = "cdns3-xhci-regs";
+ res[RES_HOST_ID].flags = IORESOURCE_MEM;
+ dev_dbg(&pdev->dev, "USBSS-XHCI physical base addr: %pa\n",
+ &res[RES_HOST_ID].start);
+
+ res[RES_DRD_ID].start = pci_resource_start(pdev, PCI_BAR_OTG);
+ res[RES_DRD_ID].end = pci_resource_end(pdev, PCI_BAR_OTG);
+ res[RES_DRD_ID].name = "cdns3-otg";
+ res[RES_DRD_ID].flags = IORESOURCE_MEM;
+ dev_dbg(&pdev->dev, "USBSS-DRD physical base addr: %pa\n",
+ &res[RES_DRD_ID].start);
+
+ /* Interrupt common for both device and XHCI */
+ wrap->dev_res[RES_IRQ_ID].start = pdev->irq;
+ wrap->dev_res[RES_IRQ_ID].name = "cdns3-irq";
+ wrap->dev_res[RES_IRQ_ID].flags = IORESOURCE_IRQ;
+
+ /* set up platform device info */
+ memset(&plat_info, 0, sizeof(plat_info));
+ plat_info.parent = &pdev->dev;
+ plat_info.fwnode = pdev->dev.fwnode;
+ plat_info.name = PLAT_DRIVER_NAME;
+ plat_info.id = pdev->devfn;
+ plat_info.res = wrap->dev_res;
+ plat_info.num_res = ARRAY_SIZE(wrap->dev_res);
+ plat_info.dma_mask = pdev->dma_mask;
+
+ /* register platform device */
+ wrap->plat_dev = platform_device_register_full(&plat_info);
+ if (IS_ERR(wrap->plat_dev)) {
+ err = PTR_ERR(wrap->plat_dev);
+ return err;
+ }
+
+ pci_set_drvdata(pdev, wrap);
+
+ return err;
+}
+
+void cdns3_pci_remove(struct pci_dev *pdev)
+{
+ struct cdns3_wrap *wrap = (struct cdns3_wrap *)pci_get_drvdata(pdev);
+
+ platform_device_unregister(wrap->plat_dev);
+}
+
+static const struct pci_device_id cdns3_pci_ids[] = {
+ { PCI_DEVICE(CDNS_VENDOR_ID, CDNS_DEVICE_ID), },
+ { 0, }
+};
+
+static struct pci_driver cdns3_pci_driver = {
+ .name = PCI_DRIVER_NAME,
+ .id_table = cdns3_pci_ids,
+ .probe = cdns3_pci_probe,
+ .remove = cdns3_pci_remove,
+};
+
+module_pci_driver(cdns3_pci_driver);
+MODULE_DEVICE_TABLE(pci, cdns3_pci_ids);
+
+MODULE_AUTHOR("Pawel Laszczak <[email protected]>");
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("Cadence USBSS PCI wrapperr");
+
diff --git a/drivers/usb/cdns3/core.c b/drivers/usb/cdns3/core.c
new file mode 100644
index 000000000000..b93e3788bd33
--- /dev/null
+++ b/drivers/usb/cdns3/core.c
@@ -0,0 +1,451 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Cadence USBSS DRD Driver.
+ *
+ * Copyright (C) 2018 Cadence.
+ * Copyright (C) 2017-2018 NXP
+ *
+ * Author: Peter Chen <[email protected]>
+ * Pawel Laszczak <[email protected]>
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/pm_runtime.h>
+
+#include "gadget.h"
+#include "core.h"
+#include "host-export.h"
+#include "gadget-export.h"
+#include "drd.h"
+#include "debug.h"
+
+static inline
+struct cdns3_role_driver *cdns3_get_current_role_driver(struct cdns3 *cdns)
+{
+ WARN_ON(cdns->role >= CDNS3_ROLE_END || !cdns->roles[cdns->role]);
+ return cdns->roles[cdns->role];
+}
+
+static inline int cdns3_role_start(struct cdns3 *cdns, enum cdns3_roles role)
+{
+ int ret;
+
+ if (WARN_ON(role >= CDNS3_ROLE_END))
+ return 0;
+
+ if (!cdns->roles[role])
+ return -ENXIO;
+
+ if (cdns->roles[role]->state == CDNS3_ROLE_STATE_ACTIVE)
+ return 0;
+
+ mutex_lock(&cdns->mutex);
+ cdns->role = role;
+ ret = cdns->roles[role]->start(cdns);
+ if (!ret)
+ cdns->roles[role]->state = CDNS3_ROLE_STATE_ACTIVE;
+ mutex_unlock(&cdns->mutex);
+ return ret;
+}
+
+void cdns3_role_stop(struct cdns3 *cdns)
+{
+ enum cdns3_roles role = cdns->role;
+
+ if (role >= CDNS3_ROLE_END) {
+ WARN_ON(role > CDNS3_ROLE_END);
+ return;
+ }
+
+ if (cdns->roles[role]->state == CDNS3_ROLE_STATE_INACTIVE)
+ return;
+
+ mutex_lock(&cdns->mutex);
+ cdns->roles[role]->stop(cdns);
+ cdns->roles[role]->state = CDNS3_ROLE_STATE_INACTIVE;
+ mutex_unlock(&cdns->mutex);
+}
+
+/*
+ * cdns->role gets from cdns3_get_initial_role, and this API tells role at the
+ * runtime.
+ * If both roles are supported, the role is selected based on vbus/id.
+ * It could be read from OTG register or external connector.
+ * If only single role is supported, only one role structure
+ * is allocated, cdns->roles[CDNS3_ROLE_HOST] or cdns->roles[CDNS3_ROLE_GADGET].
+ */
+static enum cdns3_roles cdns3_get_initial_role(struct cdns3 *cdns)
+{
+ if (cdns->roles[CDNS3_ROLE_HOST] && cdns->roles[CDNS3_ROLE_GADGET]) {
+ if (cdns3_is_host(cdns))
+ return CDNS3_ROLE_HOST;
+ if (cdns3_is_device(cdns))
+ return CDNS3_ROLE_GADGET;
+ }
+ return cdns->roles[CDNS3_ROLE_HOST]
+ ? CDNS3_ROLE_HOST
+ : CDNS3_ROLE_GADGET;
+}
+
+static void cdns3_exit_roles(struct cdns3 *cdns)
+{
+ cdns3_role_stop(cdns);
+ cdns3_drd_exit(cdns);
+}
+
+/**
+ * cdns3_core_init_role - initialize role of operation
+ * @cdns: Pointer to cdns3 structure
+ *
+ * Returns 0 on success otherwise negative errno
+ */
+static int cdns3_core_init_role(struct cdns3 *cdns)
+{
+ struct device *dev = cdns->dev;
+ enum usb_dr_mode best_dr_mode;
+ enum usb_dr_mode dr_mode;
+ int ret = 0;
+
+ dr_mode = usb_get_dr_mode(dev);
+ cdns->role = CDNS3_ROLE_END;
+
+ /*
+ * If driver can't read mode by means of usb_get_dr_mdoe function then
+ * chooses mode according with Kernel configuration. This setting
+ * can be restricted later depending on strap pin configuration.
+ */
+ if (dr_mode == USB_DR_MODE_UNKNOWN) {
+ if (IS_ENABLED(CONFIG_USB_CDNS3_HOST) &&
+ IS_ENABLED(CONFIG_USB_CDNS3_GADGET))
+ dr_mode = USB_DR_MODE_OTG;
+ else if (IS_ENABLED(CONFIG_USB_CDNS3_HOST))
+ dr_mode = USB_DR_MODE_HOST;
+ else if (IS_ENABLED(CONFIG_USB_CDNS3_GADGET))
+ dr_mode = USB_DR_MODE_PERIPHERAL;
+ }
+
+ best_dr_mode = USB_DR_MODE_OTG;
+
+ if (dr_mode == USB_DR_MODE_OTG) {
+ best_dr_mode = cdns->dr_mode;
+ } else if (cdns->dr_mode == USB_DR_MODE_OTG) {
+ best_dr_mode = dr_mode;
+ } else if (cdns->dr_mode != dr_mode) {
+ dev_err(dev, "Incorrect DRD configuration\n");
+ return -EINVAL;
+ }
+
+ dr_mode = best_dr_mode;
+
+ if (dr_mode == USB_DR_MODE_OTG || dr_mode == USB_DR_MODE_HOST) {
+ ret = cdns3_host_init(cdns);
+ if (ret) {
+ dev_err(dev, "Host initialization failed with %d\n",
+ ret);
+ goto err;
+ }
+ }
+
+ if (dr_mode == USB_DR_MODE_OTG || dr_mode == USB_DR_MODE_PERIPHERAL) {
+ ret = cdns3_gadget_init(cdns);
+ if (ret) {
+ dev_err(dev, "Device initialization failed with %d\n",
+ ret);
+ goto err;
+ }
+ }
+
+ cdns->desired_dr_mode = dr_mode;
+ cdns->dr_mode = dr_mode;
+ /*
+ * dr_mode could be change so DRD must update controller
+ * configuration
+ */
+ ret = cdns3_drd_update_mode(cdns);
+
+ cdns->role = cdns3_get_initial_role(cdns);
+
+ ret = cdns3_role_start(cdns, cdns->role);
+ if (ret) {
+ dev_err(dev, "can't start %s role\n",
+ cdns3_get_current_role_driver(cdns)->name);
+ goto err;
+ }
+
+ return ret;
+err:
+ cdns3_exit_roles(cdns);
+ return ret;
+}
+
+/**
+ * cdsn3_get_real_role - get real role of controller based on hardware settings.
+ * @cdns: Pointer to cdns3 structure
+ *
+ * Returns role
+ */
+enum cdns3_roles cdsn3_get_real_role(struct cdns3 *cdns)
+{
+ enum cdns3_roles role = CDNS3_ROLE_END;
+
+ if (cdns->current_dr_mode == USB_DR_MODE_OTG) {
+ if (cdns3_get_id(cdns))
+ role = CDNS3_ROLE_GADGET;
+ else
+ role = CDNS3_ROLE_HOST;
+ } else {
+ if (cdns3_is_host(cdns))
+ role = CDNS3_ROLE_HOST;
+ if (cdns3_is_device(cdns))
+ role = CDNS3_ROLE_GADGET;
+ }
+
+ return role;
+}
+
+/**
+ * cdns3_role_switch - work queue handler for role switch
+ *
+ * @work: work queue item structure
+ *
+ * Handles below events:
+ * - Role switch for dual-role devices
+ * - CDNS3_ROLE_GADGET <--> CDNS3_ROLE_END for peripheral-only devices
+ */
+static void cdns3_role_switch(struct work_struct *work)
+{
+ enum cdns3_roles role = CDNS3_ROLE_END;
+ struct cdns3_role_driver *role_drv;
+ enum cdns3_roles current_role;
+ struct cdns3 *cdns;
+ int ret = 0;
+
+ cdns = container_of(work, struct cdns3, role_switch_wq);
+
+ /* During switching cdns->role can be different then role */
+ role = cdsn3_get_real_role(cdns);
+
+ role_drv = cdns3_get_current_role_driver(cdns);
+
+ pm_runtime_get_sync(cdns->dev);
+
+ /* Disable current role. This state can be forced from user space. */
+ if (cdns->debug_disable && role_drv->state == CDNS3_ROLE_STATE_ACTIVE) {
+ cdns3_role_stop(cdns);
+ goto exit;
+ }
+
+ /* Do nothing if nothing changed */
+ if (cdns->role == role && role_drv->state == CDNS3_ROLE_STATE_ACTIVE)
+ goto exit;
+
+ cdns3_role_stop(cdns);
+
+ role = cdsn3_get_real_role(cdns);
+
+ current_role = cdns->role;
+ dev_dbg(cdns->dev, "Switching role");
+
+ ret = cdns3_role_start(cdns, role);
+
+ if (ret) {
+ /* Back to current role */
+ dev_err(cdns->dev, "set %d has failed, back to %d\n",
+ role, current_role);
+ cdns3_role_start(cdns, current_role);
+ }
+exit:
+ pm_runtime_put_sync(cdns->dev);
+}
+
+/**
+ * cdns3_probe - probe for cdns3 core device
+ * @pdev: Pointer to cdns3 core platform device
+ *
+ * Returns 0 on success otherwise negative errno
+ */
+static int cdns3_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct resource *res;
+ struct cdns3 *cdns;
+ void __iomem *regs;
+ int ret;
+
+ cdns = devm_kzalloc(dev, sizeof(*cdns), GFP_KERNEL);
+ if (!cdns)
+ return -ENOMEM;
+
+ cdns->dev = dev;
+
+ platform_set_drvdata(pdev, cdns);
+
+ res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+ if (!res) {
+ dev_err(dev, "missing IRQ\n");
+ return -ENODEV;
+ }
+ cdns->irq = res->start;
+
+ cdns->xhci_res[0] = *res;
+
+ /*
+ * Request memory region
+ * region-0: xHCI
+ * region-1: Peripheral
+ * region-2: OTG registers
+ */
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ cdns->xhci_res[1] = *res;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+ regs = devm_ioremap_resource(dev, res);
+ if (IS_ERR(regs))
+ return PTR_ERR(regs);
+ cdns->dev_regs = regs;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
+ regs = devm_ioremap_resource(dev, res);
+ if (IS_ERR(regs))
+ return PTR_ERR(regs);
+ cdns->otg_regs = regs;
+
+ mutex_init(&cdns->mutex);
+
+ cdns->phy = devm_phy_get(dev, "cdns3,usbphy");
+ if (IS_ERR(cdns->phy)) {
+ ret = PTR_ERR(cdns->phy);
+ if (ret == -ENOSYS || ret == -ENODEV) {
+ cdns->phy = NULL;
+ } else if (ret == -EPROBE_DEFER) {
+ return ret;
+ } else {
+ dev_err(dev, "no phy found\n");
+ goto err0;
+ }
+ }
+
+ phy_init(cdns->phy);
+
+ INIT_WORK(&cdns->role_switch_wq, cdns3_role_switch);
+
+ ret = cdns3_drd_init(cdns);
+ if (ret)
+ goto err1;
+
+ ret = cdns3_core_init_role(cdns);
+ if (ret)
+ goto err1;
+
+ cdns3_debugfs_init(cdns);
+ device_set_wakeup_capable(dev, true);
+ pm_runtime_set_active(dev);
+ pm_runtime_enable(dev);
+
+ /*
+ * The controller needs less time between bus and controller suspend,
+ * and we also needs a small delay to avoid frequently entering low
+ * power mode.
+ */
+ pm_runtime_set_autosuspend_delay(dev, 20);
+ pm_runtime_mark_last_busy(dev);
+ pm_runtime_use_autosuspend(dev);
+ dev_dbg(dev, "Cadence USB3 core: probe succeed\n");
+
+ return 0;
+
+err1:
+ phy_exit(cdns->phy);
+err0:
+ return ret;
+}
+
+/**
+ * cdns3_remove - unbind drd driver and clean up
+ * @pdev: Pointer to Linux platform device
+ *
+ * Returns 0 on success otherwise negative errno
+ */
+static int cdns3_remove(struct platform_device *pdev)
+{
+ struct cdns3 *cdns = platform_get_drvdata(pdev);
+
+ pm_runtime_get_sync(&pdev->dev);
+ pm_runtime_disable(&pdev->dev);
+ pm_runtime_put_noidle(&pdev->dev);
+ cdns3_debugfs_exit(cdns);
+ cdns3_exit_roles(cdns);
+ phy_exit(cdns->phy);
+ return 0;
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id of_cdns3_match[] = {
+ { .compatible = "cdns,usb3" },
+ { },
+};
+MODULE_DEVICE_TABLE(of, of_cdns3_match);
+#endif
+
+#ifdef CONFIG_PM
+
+#ifdef CONFIG_PM_SLEEP
+static int cdns3_suspend(struct device *dev)
+{
+ /* TODO: Implements this function. */
+ return 0;
+}
+
+static int cdns3_resume(struct device *dev)
+{
+ /* TODO: Implements this function. */
+ return 0;
+}
+#endif /* CONFIG_PM_SLEEP */
+static int cdns3_runtime_suspend(struct device *dev)
+{ /* TODO: Implements this function. */
+ return 0;
+}
+
+static int cdns3_runtime_resume(struct device *dev)
+{
+ /* TODO: Implements this function. */
+ return 0;
+}
+#endif /* CONFIG_PM */
+
+static const struct dev_pm_ops cdns3_pm_ops = {
+ SET_SYSTEM_SLEEP_PM_OPS(cdns3_suspend, cdns3_resume)
+ SET_RUNTIME_PM_OPS(cdns3_runtime_suspend, cdns3_runtime_resume, NULL)
+};
+
+static struct platform_driver cdns3_driver = {
+ .probe = cdns3_probe,
+ .remove = cdns3_remove,
+ .driver = {
+ .name = "cdns-usb3",
+ .of_match_table = of_match_ptr(of_cdns3_match),
+ .pm = &cdns3_pm_ops,
+ },
+};
+
+static int __init cdns3_driver_platform_register(void)
+{
+ return platform_driver_register(&cdns3_driver);
+}
+module_init(cdns3_driver_platform_register);
+
+static void __exit cdns3_driver_platform_unregister(void)
+{
+ platform_driver_unregister(&cdns3_driver);
+}
+module_exit(cdns3_driver_platform_unregister);
+
+MODULE_ALIAS("platform:cdns3");
+MODULE_AUTHOR("Pawel Laszczak <[email protected]>");
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("Cadence USB3 DRD Controller Driver");
diff --git a/drivers/usb/cdns3/core.h b/drivers/usb/cdns3/core.h
new file mode 100644
index 000000000000..ffd1971ff893
--- /dev/null
+++ b/drivers/usb/cdns3/core.h
@@ -0,0 +1,108 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Cadence USBSS DRD Header File.
+ *
+ * Copyright (C) 2017-2018 NXP
+ * Copyright (C) 2018 Cadence.
+ *
+ * Authors: Peter Chen <[email protected]>
+ * Pawel Laszczak <[email protected]>
+ */
+#include <linux/usb/otg.h>
+
+#ifndef __LINUX_CDNS3_CORE_H
+#define __LINUX_CDNS3_CORE_H
+
+struct cdns3;
+enum cdns3_roles {
+ CDNS3_ROLE_HOST = 0,
+ CDNS3_ROLE_GADGET,
+ CDNS3_ROLE_END,
+};
+
+/**
+ * struct cdns3_role_driver - host/gadget role driver
+ * @start: start this role
+ * @stop: stop this role
+ * @suspend: suspend callback for this role
+ * @resume: resume callback for this role
+ * @irq: irq handler for this role
+ * @name: role name string (host/gadget)
+ * @state: current state
+ */
+struct cdns3_role_driver {
+ int (*start)(struct cdns3 *cdns);
+ void (*stop)(struct cdns3 *cdns);
+ int (*suspend)(struct cdns3 *cdns, bool do_wakeup);
+ int (*resume)(struct cdns3 *cdns, bool hibernated);
+ const char *name;
+#define CDNS3_ROLE_STATE_INACTIVE 0
+#define CDNS3_ROLE_STATE_ACTIVE 1
+ int state;
+};
+
+#define CDNS3_XHCI_RESOURCES_NUM 2
+/**
+ * struct cdns3 - Representation of Cadence USB3 DRD controller.
+ * @dev: pointer to Cadence device struct
+ * @xhci_regs: pointer to base of xhci registers
+ * @xhci_res: the resource for xhci
+ * @dev_regs: pointer to base of dev registers
+ * @otg_regs: pointer to base of otg registers
+ * @irq: irq number for controller
+ * @roles: array of supported roles for this controller
+ * @role: current role
+ * @host_dev: the child host device pointer for cdns3 core
+ * @gadget_dev: the child gadget device pointer for cdns3 core
+ * @usb: phy for this controller
+ * @role_switch_wq: work queue item for role switch
+ * @in_lpm: the controller in low power mode
+ * @wakeup_int: the wakeup interrupt
+ * @mutex: the mutex for concurrent code at driver
+ * @dr_mode: supported mode of operation it can be only Host, only Device
+ * or OTG mode that allow to switch between Device and Host mode.
+ * This field based on firmware setting, kernel configuration
+ * and hardware configuration.
+ * @current_dr_mode: current mode of operation when in dual-role mode
+ * @desired_dr_mode: desired mode of operation when in dual-role mode.
+ * This value can be changed during runtime.
+ * Available options depends on dr_mode:
+ * dr_mode | desired_dr_mode and current_dr_mode
+ * ----------------------------------------------------------------
+ * USB_DR_MODE_HOST | only USB_DR_MODE_HOST
+ * USB_DR_MODE_PERIPHERAL | only USB_DR_MODE_PERIPHERAL
+ * USB_DR_MODE_OTG | only USB_DR_MODE_HOST
+ * USB_DR_MODE_OTG | only USB_DR_MODE_PERIPHERAL
+ * USB_DR_MODE_OTG | USB_DR_MODE_OTG
+ *
+ * Desired_dr_role can be changed by means of debugfs.
+ * @root: debugfs root folder pointer
+ * @debug_disable:
+ */
+struct cdns3 {
+ struct device *dev;
+ void __iomem *xhci_regs;
+ struct resource xhci_res[CDNS3_XHCI_RESOURCES_NUM];
+ struct cdns3_usb_regs __iomem *dev_regs;
+ struct cdns3_otg_regs *otg_regs;
+ int irq;
+ struct cdns3_role_driver *roles[CDNS3_ROLE_END];
+ enum cdns3_roles role;
+ struct platform_device *host_dev;
+ struct cdns3_device *gadget_dev;
+ struct phy *phy;
+ struct work_struct role_switch_wq;
+ int in_lpm:1;
+ int wakeup_int:1;
+ /* mutext used in workqueue*/
+ struct mutex mutex;
+ enum usb_dr_mode dr_mode;
+ enum usb_dr_mode current_dr_mode;
+ enum usb_dr_mode desired_dr_mode;
+ struct dentry *root;
+ int debug_disable:1;
+};
+
+void cdns3_role_stop(struct cdns3 *cdns);
+
+#endif /* __LINUX_CDNS3_CORE_H */
diff --git a/drivers/usb/cdns3/debug.h b/drivers/usb/cdns3/debug.h
new file mode 100644
index 000000000000..afb81d224718
--- /dev/null
+++ b/drivers/usb/cdns3/debug.h
@@ -0,0 +1,346 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Cadence USBSS DRD Driver.
+ * Debug header file.
+ *
+ * Copyright (C) 2018 Cadence.
+ *
+ * Author: Pawel Laszczak <[email protected]>
+ */
+#ifndef __LINUX_CDNS3_DEBUG
+#define __LINUX_CDNS3_DEBUG
+#include "gadget.h"
+
+static inline void cdns3_decode_get_status(u8 bRequestType, u16 wIndex,
+ u16 wLength, char *str)
+{
+ switch (bRequestType & USB_RECIP_MASK) {
+ case USB_RECIP_INTERFACE:
+ sprintf(str, "Get Interface Status Intf = %d, L: = %d",
+ wIndex, wLength);
+ break;
+ case USB_RECIP_ENDPOINT:
+ sprintf(str, "Get Endpoint Status ep%d%s",
+ wIndex & ~USB_DIR_IN,
+ wIndex & USB_DIR_IN ? "in" : "out");
+ break;
+ }
+}
+
+static inline const char *cdns3_decode_device_feature(u16 wValue)
+{
+ switch (wValue) {
+ case USB_DEVICE_SELF_POWERED:
+ return "Self Powered";
+ case USB_DEVICE_REMOTE_WAKEUP:
+ return "Remote Wakeup";
+ case USB_DEVICE_TEST_MODE:
+ return "Test Mode";
+ case USB_DEVICE_U1_ENABLE:
+ return "U1 Enable";
+ case USB_DEVICE_U2_ENABLE:
+ return "U2 Enable";
+ case USB_DEVICE_LTM_ENABLE:
+ return "LTM Enable";
+ default:
+ return "UNKNOWN";
+ }
+}
+
+static inline const char *cdns3_decode_test_mode(u16 wIndex)
+{
+ switch (wIndex) {
+ case TEST_J:
+ return ": TEST_J";
+ case TEST_K:
+ return ": TEST_K";
+ case TEST_SE0_NAK:
+ return ": TEST_SE0_NAK";
+ case TEST_PACKET:
+ return ": TEST_PACKET";
+ case TEST_FORCE_EN:
+ return ": TEST_FORCE_EN";
+ default:
+ return ": UNKNOWN";
+ }
+}
+
+static inline void cdns3_decode_set_clear_feature(u8 bRequestType, u8 bRequest,
+ u16 wValue, u16 wIndex,
+ char *str)
+{
+ switch (bRequestType & USB_RECIP_MASK) {
+ case USB_RECIP_DEVICE:
+ sprintf(str, "%s Device Feature(%s%s)",
+ bRequest == USB_REQ_CLEAR_FEATURE ? "Clear" : "Set",
+ cdns3_decode_device_feature(wValue),
+ wValue == USB_DEVICE_TEST_MODE ?
+ cdns3_decode_test_mode(wIndex) : "");
+ break;
+ case USB_RECIP_INTERFACE:
+ sprintf(str, "%s Interface Feature(%s)",
+ bRequest == USB_REQ_CLEAR_FEATURE ? "Clear" : "Set",
+ wIndex == USB_INTRF_FUNC_SUSPEND ?
+ "Function Suspend" : "UNKNOWN");
+ break;
+ case USB_RECIP_ENDPOINT:
+ sprintf(str, "%s Endpoint Feature(%s ep%d%s)",
+ bRequest == USB_REQ_CLEAR_FEATURE ? "Clear" : "Set",
+ wIndex == USB_ENDPOINT_HALT ? "Halt" : "UNKNOWN",
+ wIndex & ~USB_DIR_IN,
+ wIndex & USB_DIR_IN ? "in" : "out");
+ break;
+ }
+}
+
+static inline const char *cdns3_decode_descriptor(u16 wValue)
+{
+ switch (wValue >> 8) {
+ case USB_DT_DEVICE:
+ return "Device";
+ case USB_DT_CONFIG:
+ return "Configuration";
+ case USB_DT_STRING:
+ return "String";
+ case USB_DT_INTERFACE:
+ return "Interface";
+ case USB_DT_ENDPOINT:
+ return "Endpoint";
+ case USB_DT_DEVICE_QUALIFIER:
+ return "Device Qualifier";
+ case USB_DT_OTHER_SPEED_CONFIG:
+ return "Other Speed Config";
+ case USB_DT_INTERFACE_POWER:
+ return "Interface Power";
+ case USB_DT_OTG:
+ return "OTG";
+ case USB_DT_DEBUG:
+ return "Debug";
+ case USB_DT_INTERFACE_ASSOCIATION:
+ return "Interface Association";
+ case USB_DT_BOS:
+ return "BOS";
+ case USB_DT_DEVICE_CAPABILITY:
+ return "Device Capability";
+ case USB_DT_SS_ENDPOINT_COMP:
+ return "SS Endpoint Companion";
+ case USB_DT_SSP_ISOC_ENDPOINT_COMP:
+ return "SSP Isochronous Endpoint Companion";
+ default:
+ return "UNKNOWN";
+ }
+}
+
+/**
+ * cdns3_decode_ctrl - returns a string represetion of ctrl request
+ */
+static inline const char *cdns3_decode_ctrl(char *str, u8 bRequestType,
+ u8 bRequest, u16 wValue,
+ u16 wIndex, u16 wLength)
+{
+ switch (bRequest) {
+ case USB_REQ_GET_STATUS:
+ cdns3_decode_get_status(bRequestType, wIndex,
+ wLength, str);
+ break;
+ case USB_REQ_CLEAR_FEATURE:
+ case USB_REQ_SET_FEATURE:
+ cdns3_decode_set_clear_feature(bRequestType, bRequest,
+ wValue, wIndex, str);
+ break;
+ case USB_REQ_SET_ADDRESS:
+ sprintf(str, "Set Address Addr: %02x", wValue);
+ break;
+ case USB_REQ_GET_DESCRIPTOR:
+ sprintf(str, "GET %s Descriptor I: %d, L: %d",
+ cdns3_decode_descriptor(wValue),
+ wValue & 0xff, wLength);
+ break;
+ case USB_REQ_SET_DESCRIPTOR:
+ sprintf(str, "SET %s Descriptor I: %d, L: %d",
+ cdns3_decode_descriptor(wValue),
+ wValue & 0xff, wLength);
+ break;
+ case USB_REQ_GET_CONFIGURATION:
+ sprintf(str, "Get Configuration L: %d", wLength);
+ break;
+ case USB_REQ_SET_CONFIGURATION:
+ sprintf(str, "Set Configuration Config: %d ", wValue);
+ break;
+ case USB_REQ_GET_INTERFACE:
+ sprintf(str, "Get Interface Intf: %d, L: %d", wIndex, wLength);
+ break;
+ case USB_REQ_SET_INTERFACE:
+ sprintf(str, "Set Interface Intf: %d, Alt: %d", wIndex, wValue);
+ break;
+ case USB_REQ_SYNCH_FRAME:
+ sprintf(str, "Synch Frame Ep: %d, L: %d", wIndex, wLength);
+ break;
+ case USB_REQ_SET_SEL:
+ sprintf(str, "Set SEL L: %d", wLength);
+ break;
+ case USB_REQ_SET_ISOCH_DELAY:
+ sprintf(str, "Set Isochronous Delay Delay: %d ns", wValue);
+ break;
+ default:
+ sprintf(str,
+ "SETUP BRT: %02x BR: %02x V: %04x I: %04x L: %04x\n",
+ bRequestType, bRequest,
+ wValue, wIndex, wLength);
+ }
+
+ return str;
+}
+
+static inline char *cdns3_decode_usb_irq(struct cdns3_device *priv_dev,
+ u32 usb_ists)
+{
+ static char str[256];
+ int ret;
+
+ ret = sprintf(str, "IRQ %08x = ", usb_ists);
+
+ if (usb_ists & (USB_ISTS_CON2I | USB_ISTS_CONI)) {
+ u32 speed = cdns3_get_speed(priv_dev);
+
+ ret += sprintf(str + ret, "Connection %s\n",
+ usb_speed_string(speed));
+ }
+ if (usb_ists & USB_ISTS_CON2I || usb_ists & USB_ISTS_CONI)
+ ret += sprintf(str + ret, "Disconnection ");
+ if (usb_ists & USB_ISTS_L2ENTI)
+ ret += sprintf(str + ret, "suspended ");
+
+ if (usb_ists & USB_ISTS_L2EXTI)
+ ret += sprintf(str + ret, "L2 exit ");
+ if (usb_ists & USB_ISTS_U3EXTI)
+ ret += sprintf(str + ret, "U3 exit ");
+ if (usb_ists & USB_ISTS_UWRESI)
+ ret += sprintf(str + ret, "Warm Reset ");
+ if (usb_ists & USB_ISTS_UHRESI)
+ ret += sprintf(str + ret, "Hot Reset ");
+ if (usb_ists & USB_ISTS_U2RESI)
+ ret += sprintf(str + ret, "Reset");
+
+ return str;
+}
+
+static inline char *cdns3_decode_ep_irq(u32 ep_sts, const char *ep_name)
+{
+ static char str[256];
+ int ret;
+
+ ret = sprintf(str, "IRQ for %s: %08x ", ep_name, ep_sts);
+
+ if (ep_sts & EP_STS_SETUP)
+ ret += sprintf(str + ret, "SETUP ");
+ if (ep_sts & EP_STS_IOC)
+ ret += sprintf(str + ret, "IOC ");
+ if (ep_sts & EP_STS_ISP)
+ ret += sprintf(str + ret, "ISP ");
+ if (ep_sts & EP_STS_DESCMIS)
+ ret += sprintf(str + ret, "DESCMIS ");
+ if (ep_sts & EP_STS_STREAMR)
+ ret += sprintf(str + ret, "STREAMR ");
+ if (ep_sts & EP_STS_MD_EXIT)
+ ret += sprintf(str + ret, "MD_EXIT ");
+ if (ep_sts & EP_STS_TRBERR)
+ ret += sprintf(str + ret, "TRBERR ");
+ if (ep_sts & EP_STS_NRDY)
+ ret += sprintf(str + ret, "NRDY ");
+ if (ep_sts & EP_STS_PRIME)
+ ret += sprintf(str + ret, "PRIME ");
+ if (ep_sts & EP_STS_SIDERR)
+ ret += sprintf(str + ret, "SIDERRT ");
+ if (ep_sts & EP_STS_OUTSMM)
+ ret += sprintf(str + ret, "OUTSMM ");
+ if (ep_sts & EP_STS_ISOERR)
+ ret += sprintf(str + ret, "ISOERR ");
+ if (ep_sts & EP_STS_IOT)
+ ret += sprintf(str + ret, "IOT ");
+
+ return str;
+}
+
+static inline char *cdns3_decode_epx_irq(struct cdns3_endpoint *priv_ep)
+{
+ struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
+
+ return cdns3_decode_ep_irq(readl(&priv_dev->regs->ep_sts),
+ priv_ep->name);
+}
+
+static inline char *cdns3_decode_ep0_irq(struct cdns3_device *priv_dev)
+{
+ if (priv_dev->ep0_data_dir)
+ return cdns3_decode_ep_irq(readl(&priv_dev->regs->ep_sts),
+ "ep0IN");
+ else
+ return cdns3_decode_ep_irq(readl(&priv_dev->regs->ep_sts),
+ "ep0OUT");
+}
+
+/**
+ * Debug a transfer ring.
+ *
+ * Prints out all TRBs in the endpoint ring, even those after the Link TRB.
+ *.
+ */
+static inline char *cdns3_dbg_ring(struct cdns3_endpoint *priv_ep,
+ int free_trbs, u8 pcs, u8 ccs,
+ int enqueue, int dequeue,
+ struct cdns3_trb *ring, char *str)
+{
+ u64 addr = priv_ep->trb_pool_dma;
+ struct cdns3_trb *trb;
+ int ret = 0;
+ int i;
+
+ trb = &ring[priv_ep->dequeue];
+ ret += sprintf(str + ret, "\n\t\tRing contents for %s:", priv_ep->name);
+
+ ret += sprintf(str + ret,
+ "\n\t\tRing deq index: %d, trb: %p (virt), 0x%llx (dma)\n",
+ dequeue, trb,
+ (unsigned long long)cdns3_trb_virt_to_dma(priv_ep, trb));
+
+ trb = &ring[priv_ep->enqueue];
+ ret += sprintf(str + ret,
+ "\t\tRing enq index: %d, trb: %p (virt), 0x%llx (dma)\n",
+ enqueue, trb,
+ (unsigned long long)cdns3_trb_virt_to_dma(priv_ep, trb));
+
+ ret += sprintf(str + ret,
+ "\t\tfree trbs: %d, CCS=%d, PCS=%d\n", free_trbs, ccs,
+ pcs);
+
+ if (TRBS_PER_SEGMENT > 64) {
+ sprintf(str + ret, "\t\tTo big transfer ring %d\n",
+ TRBS_PER_SEGMENT);
+ return str;
+ }
+
+ for (i = 0; i < TRBS_PER_SEGMENT; ++i) {
+ trb = &ring[i];
+ ret += sprintf(str + ret,
+ "\t\t@%016llx %08x %08x %08x\n", addr,
+ le32_to_cpu(trb->buffer),
+ le32_to_cpu(trb->length),
+ le32_to_cpu(trb->control));
+ addr += sizeof(*trb);
+ }
+
+ return str;
+}
+
+#ifdef CONFIG_DEBUG_FS
+void cdns3_debugfs_init(struct cdns3 *cdns);
+void cdns3_debugfs_exit(struct cdns3 *cdns);
+#else
+void cdns3_debugfs_init(struct cdns3 *cdns);
+{ }
+void cdns3_debugfs_exit(struct cdns3 *cdns);
+{ }
+#endif
+
+#endif /*__LINUX_CDNS3_DEBUG*/
diff --git a/drivers/usb/cdns3/debugfs.c b/drivers/usb/cdns3/debugfs.c
new file mode 100644
index 000000000000..d7919f5c1d90
--- /dev/null
+++ b/drivers/usb/cdns3/debugfs.c
@@ -0,0 +1,168 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Cadence USBSS DRD Controller DebugFS filer.
+ *
+ * Copyright (C) 2018 Cadence.
+ *
+ * Author: Pawel Laszczak <[email protected]>
+ */
+
+#include <linux/types.h>
+#include <linux/debugfs.h>
+#include <linux/seq_file.h>
+#include <linux/uaccess.h>
+
+#include "core.h"
+#include "gadget.h"
+#include "drd.h"
+
+static int cdns3_mode_show(struct seq_file *s, void *unused)
+{
+ struct cdns3 *cdns = s->private;
+
+ switch (cdns->current_dr_mode) {
+ case USB_DR_MODE_HOST:
+ seq_puts(s, "host\n");
+ break;
+ case USB_DR_MODE_PERIPHERAL:
+ seq_puts(s, "device\n");
+ break;
+ case USB_DR_MODE_OTG:
+ seq_puts(s, "otg\n");
+ break;
+ default:
+ seq_puts(s, "UNKNOWN mode\n");
+ }
+
+ return 0;
+}
+
+static int cdns3_mode_open(struct inode *inode, struct file *file)
+{
+ return single_open(file, cdns3_mode_show, inode->i_private);
+}
+
+static ssize_t cdns3_mode_write(struct file *file,
+ const char __user *ubuf,
+ size_t count, loff_t *ppos)
+{
+ struct seq_file *s = file->private_data;
+ struct cdns3 *cdns = s->private;
+ u32 mode = USB_DR_MODE_UNKNOWN;
+ char buf[32];
+
+ if (copy_from_user(&buf, ubuf, min_t(size_t, sizeof(buf) - 1, count)))
+ return -EFAULT;
+
+ if (!strncmp(buf, "host", 4)) {
+ if (cdns->dr_mode == USB_DR_MODE_HOST ||
+ cdns->dr_mode == USB_DR_MODE_OTG) {
+ mode = USB_DR_MODE_HOST;
+ }
+ }
+
+ if (!strncmp(buf, "device", 6))
+ if (cdns->dr_mode == USB_DR_MODE_PERIPHERAL ||
+ cdns->dr_mode == USB_DR_MODE_OTG)
+ mode = USB_DR_MODE_PERIPHERAL;
+
+ if (!strncmp(buf, "otg", 3) && cdns->dr_mode == USB_DR_MODE_OTG)
+ mode = USB_DR_MODE_OTG;
+
+ if (mode == USB_DR_MODE_UNKNOWN) {
+ dev_err(cdns->dev, "Failed: incorrect mode setting\n");
+ return -EFAULT;
+ }
+
+ if (cdns->current_dr_mode != mode) {
+ cdns->desired_dr_mode = mode;
+ cdns->debug_disable = 0;
+ cdns3_role_stop(cdns);
+ cdns3_drd_update_mode(cdns);
+ queue_work(system_freezable_wq, &cdns->role_switch_wq);
+ }
+
+ return count;
+}
+
+static const struct file_operations cdns3_mode_fops = {
+ .open = cdns3_mode_open,
+ .write = cdns3_mode_write,
+ .read = seq_read,
+ .llseek = seq_lseek,
+ .release = single_release,
+};
+
+static int cdns3_disable_show(struct seq_file *s, void *unused)
+{
+ struct cdns3 *cdns = s->private;
+
+ if (!cdns->debug_disable)
+ seq_puts(s, "0\n");
+ else
+ seq_puts(s, "1\n");
+
+ return 0;
+}
+
+static ssize_t cdns3_disable_write(struct file *file,
+ const char __user *ubuf,
+ size_t count, loff_t *ppos)
+{
+ struct seq_file *s = file->private_data;
+ struct cdns3 *cdns = s->private;
+ int disable;
+ char buf[32];
+
+ if (copy_from_user(&buf, ubuf, min_t(size_t, sizeof(buf) - 1, count)))
+ return -EFAULT;
+
+ if (!strncmp(buf, "1", 1) || !strncmp(buf, "yes", 3)) {
+ disable = 1;
+ } else if (!strncmp(buf, "0", 1) || !strncmp(buf, "no", 2)) {
+ disable = 0;
+ } else {
+ dev_err(cdns->dev, "Failed: incorrect disable setting\n");
+ return -EFAULT;
+ }
+
+ if (disable != cdns->debug_disable) {
+ cdns->debug_disable = disable;
+ queue_work(system_freezable_wq, &cdns->role_switch_wq);
+ }
+
+ return count;
+}
+
+static int cdns3_disable_open(struct inode *inode, struct file *file)
+{
+ return single_open(file, cdns3_disable_show, inode->i_private);
+}
+
+static const struct file_operations cdns3_disable_fops = {
+ .open = cdns3_disable_open,
+ .write = cdns3_disable_write,
+ .read = seq_read,
+ .llseek = seq_lseek,
+ .release = single_release,
+};
+
+void cdns3_debugfs_init(struct cdns3 *cdns)
+{
+ struct dentry *root;
+
+ root = debugfs_create_dir(dev_name(cdns->dev), NULL);
+ cdns->root = root;
+ if (IS_ENABLED(CONFIG_USB_CDNS3_GADGET) &&
+ IS_ENABLED(CONFIG_USB_CDNS3_HOST))
+ debugfs_create_file("mode", 0644, root, cdns,
+ &cdns3_mode_fops);
+
+ debugfs_create_file("disable", 0644, root, cdns,
+ &cdns3_disable_fops);
+}
+
+void cdns3_debugfs_exit(struct cdns3 *cdns)
+{
+ debugfs_remove_recursive(cdns->root);
+}
diff --git a/drivers/usb/cdns3/drd.c b/drivers/usb/cdns3/drd.c
new file mode 100644
index 000000000000..45573427ba83
--- /dev/null
+++ b/drivers/usb/cdns3/drd.c
@@ -0,0 +1,315 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Cadence USBSS DRD Driver.
+ *
+ * Copyright (C) 2018 Cadence.
+ *
+ * Author: Pawel Laszczak <[email protected]
+ *
+ */
+#include <linux/kernel.h>
+#include <linux/interrupt.h>
+#include <linux/delay.h>
+#include <linux/usb/otg.h>
+
+#include "gadget.h"
+#include "drd.h"
+#include "core.h"
+
+static int cdns3_drd_switch_gadget(struct cdns3 *cdns, int on);
+static int cdns3_drd_switch_host(struct cdns3 *cdns, int on);
+
+/**
+ * cdns3_set_mode - change mode of OTG Core
+ * @cdns: pointer to context structure
+ * @mode: selected mode from cdns_role
+ */
+void cdns3_set_mode(struct cdns3 *cdns, enum usb_dr_mode mode)
+{
+ u32 reg;
+
+ cdns->current_dr_mode = mode;
+
+ switch (mode) {
+ case USB_DR_MODE_PERIPHERAL:
+ dev_info(cdns->dev, "Set controller to Gadget mode\n");
+ cdns3_drd_switch_gadget(cdns, 1);
+ break;
+ case USB_DR_MODE_HOST:
+ dev_info(cdns->dev, "Set controller to Host mode\n");
+ cdns3_drd_switch_host(cdns, 1);
+ break;
+ case USB_DR_MODE_OTG:
+ dev_info(cdns->dev, "Set controller to OTG mode\n");
+ reg = readl(&cdns->otg_regs->override);
+ reg |= OVERRIDE_IDPULLUP;
+ writel(reg, &cdns->otg_regs->override);
+
+ /*
+ * Hardware specification says: "ID_VALUE must be valid within
+ * 50ms after idpullup is set to '1" so driver must wait
+ * 50ms before reading this pin.
+ */
+ usleep_range(50000, 60000);
+ break;
+ default:
+ cdns->current_dr_mode = USB_DR_MODE_UNKNOWN;
+ dev_err(cdns->dev, "Unsupported mode of operation %d\n", mode);
+ return;
+ }
+}
+
+int cdns3_get_id(struct cdns3 *cdns)
+{
+ int id;
+
+ id = readl(&cdns->otg_regs->sts) & OTGSTS_ID_VALUE;
+ dev_dbg(cdns->dev, "OTG ID: %d", id);
+ return id;
+}
+
+int cdns3_is_host(struct cdns3 *cdns)
+{
+ if (cdns->current_dr_mode == USB_DR_MODE_HOST)
+ return 1;
+ else if (!cdns3_get_id(cdns))
+ return 1;
+
+ return 0;
+}
+
+int cdns3_is_device(struct cdns3 *cdns)
+{
+ if (cdns->current_dr_mode == USB_DR_MODE_PERIPHERAL)
+ return 1;
+ else if (cdns->current_dr_mode == USB_DR_MODE_OTG)
+ if (cdns3_get_id(cdns))
+ return 1;
+
+ return 0;
+}
+
+/**
+ * cdns3_otg_disable_irq - Disable all OTG interrupts
+ * @cdns: Pointer to controller context structure
+ */
+static void cdns3_otg_disable_irq(struct cdns3 *cdns)
+{
+ writel(0, &cdns->otg_regs->ien);
+}
+
+/**
+ * cdns3_otg_enable_irq - enable id and sess_valid interrupts
+ * @cdns: Pointer to controller context structure
+ */
+static void cdns3_otg_enable_irq(struct cdns3 *cdns)
+{
+ writel(OTGIEN_ID_CHANGE_INT | OTGIEN_VBUSVALID_RISE_INT |
+ OTGIEN_VBUSVALID_FALL_INT, &cdns->otg_regs->ien);
+}
+
+/**
+ * cdns3_drd_switch_host - start/stop host
+ * @cdns: Pointer to controller context structure
+ * @on: 1 for start, 0 for stop
+ *
+ * Returns 0 on success otherwise negative errno
+ */
+static int cdns3_drd_switch_host(struct cdns3 *cdns, int on)
+{
+ int ret;
+ u32 reg = OTGCMD_OTG_DIS;
+
+ /* switch OTG core */
+ if (on) {
+ writel(OTGCMD_HOST_BUS_REQ | reg, &cdns->otg_regs->cmd);
+
+ dev_dbg(cdns->dev, "Waiting for Host mode is turned on\n");
+ ret = cdns3_handshake(&cdns->otg_regs->sts, OTGSTS_XHCI_READY,
+ OTGSTS_XHCI_READY, 100000);
+
+ if (ret)
+ return ret;
+ } else {
+ usleep_range(30, 40);
+ writel(OTGCMD_HOST_BUS_DROP | OTGCMD_DEV_BUS_DROP |
+ OTGCMD_DEV_POWER_OFF | OTGCMD_HOST_POWER_OFF,
+ &cdns->otg_regs->cmd);
+ }
+
+ return 0;
+}
+
+/**
+ * cdns3_drd_switch_gadget - start/stop gadget
+ * @cdns: Pointer to controller context structure
+ * @on: 1 for start, 0 for stop
+ *
+ * Returns 0 on success otherwise negative errno
+ */
+static int cdns3_drd_switch_gadget(struct cdns3 *cdns, int on)
+{
+ int ret;
+ u32 reg = OTGCMD_OTG_DIS;
+
+ /* switch OTG core */
+ if (on) {
+ writel(OTGCMD_DEV_BUS_REQ | reg, &cdns->otg_regs->cmd);
+
+ dev_dbg(cdns->dev, "Waiting for Device mode is turned on\n");
+
+ ret = cdns3_handshake(&cdns->otg_regs->sts, OTGSTS_DEV_READY,
+ OTGSTS_DEV_READY, 100000);
+
+ if (ret)
+ return ret;
+ } else {
+ /*
+ * driver should wait at least 10us after disabling Device
+ * before turning-off Device (DEV_BUS_DROP)
+ */
+ usleep_range(20, 30);
+ writel(OTGCMD_HOST_BUS_DROP | OTGCMD_DEV_BUS_DROP |
+ OTGCMD_DEV_POWER_OFF | OTGCMD_HOST_POWER_OFF,
+ &cdns->otg_regs->cmd);
+ }
+
+ return 0;
+}
+
+/**
+ * cdns3_init_otg_mode - initialize drd controller
+ * @cdns: Pointer to controller context structure
+ *
+ * Returns 0 on success otherwise negative errno
+ */
+static void cdns3_init_otg_mode(struct cdns3 *cdns)
+{
+ cdns3_otg_disable_irq(cdns);
+ /* clear all interrupts */
+ writel(~0, &cdns->otg_regs->ivect);
+
+ cdns3_set_mode(cdns, USB_DR_MODE_OTG);
+
+ if (cdns3_is_host(cdns))
+ cdns3_drd_switch_host(cdns, 1);
+ else
+ cdns3_drd_switch_gadget(cdns, 1);
+
+ cdns3_otg_enable_irq(cdns);
+}
+
+/**
+ * cdns3_drd_update_mode - initialize mode of operation
+ * @cdns: Pointer to controller context structure
+ *
+ * Returns 0 on success otherwise negative errno
+ */
+int cdns3_drd_update_mode(struct cdns3 *cdns)
+{
+ int ret = 0;
+
+ if (cdns->desired_dr_mode == cdns->current_dr_mode)
+ return ret;
+
+ cdns3_drd_switch_gadget(cdns, 0);
+ cdns3_drd_switch_host(cdns, 0);
+
+ switch (cdns->desired_dr_mode) {
+ case USB_DR_MODE_PERIPHERAL:
+ cdns3_set_mode(cdns, USB_DR_MODE_PERIPHERAL);
+ break;
+ case USB_DR_MODE_HOST:
+ cdns3_set_mode(cdns, USB_DR_MODE_HOST);
+ break;
+ case USB_DR_MODE_OTG:
+ cdns3_init_otg_mode(cdns);
+ break;
+ default:
+ dev_err(cdns->dev, "Unsupported mode of operation %d\n",
+ cdns->dr_mode);
+ return -EINVAL;
+ }
+
+ return ret;
+}
+
+/**
+ * cdns3_drd_irq - interrupt handler for OTG events
+ *
+ * @irq: irq number for cdns3 core device
+ * @data: structure of cdns3
+ *
+ * Returns IRQ_HANDLED or IRQ_NONE
+ */
+static irqreturn_t cdns3_drd_irq(int irq, void *data)
+{
+ irqreturn_t ret = IRQ_NONE;
+ struct cdns3 *cdns = data;
+ u32 reg;
+
+ if (cdns->dr_mode != USB_DR_MODE_OTG)
+ return ret;
+
+ reg = readl(&cdns->otg_regs->ivect);
+ if (!reg)
+ return ret;
+
+ if (reg & OTGIEN_ID_CHANGE_INT) {
+ dev_dbg(cdns->dev, "OTG IRQ: new ID: %d\n",
+ cdns3_get_id(cdns));
+
+ queue_work(system_freezable_wq, &cdns->role_switch_wq);
+
+ ret = IRQ_HANDLED;
+ }
+
+ writel(~0, &cdns->otg_regs->ivect);
+ return ret;
+}
+
+int cdns3_drd_init(struct cdns3 *cdns)
+{
+ int ret = 0;
+ u32 state;
+
+ state = OTGSTS_STRAP(readl(&cdns->otg_regs->sts));
+
+ /* Update dr_mode according to STRAP configuration. */
+ cdns->dr_mode = USB_DR_MODE_OTG;
+ if (state == OTGSTS_STRAP_HOST) {
+ dev_info(cdns->dev, "Controller strapped to HOST\n");
+ cdns->dr_mode = USB_DR_MODE_HOST;
+ } else if (state == OTGSTS_STRAP_GADGET) {
+ dev_info(cdns->dev, "Controller strapped to PERIPHERAL\n");
+ cdns->dr_mode = USB_DR_MODE_PERIPHERAL;
+ }
+
+ cdns->desired_dr_mode = cdns->dr_mode;
+ cdns->current_dr_mode = USB_DR_MODE_UNKNOWN;
+
+ ret = devm_request_irq(cdns->dev, cdns->irq, cdns3_drd_irq, IRQF_SHARED,
+ dev_name(cdns->dev), cdns);
+
+ if (ret)
+ return ret;
+
+ state = readl(&cdns->otg_regs->sts);
+ if (OTGSTS_OTG_NRDY(state) != 0) {
+ dev_err(cdns->dev, "Cadence USB3 OTG device not ready\n");
+ return -ENODEV;
+ }
+
+ ret = cdns3_drd_update_mode(cdns);
+
+ dev_info(cdns->dev, "Controller Device ID: %08lx, Revision ID: %08lx\n",
+ CDNS_RID(readl(&cdns->otg_regs->rid)),
+ CDNS_DID(readl(&cdns->otg_regs->did)));
+
+ return ret;
+}
+
+int cdns3_drd_exit(struct cdns3 *cdns)
+{
+ return cdns3_drd_switch_host(cdns, 0);
+}
diff --git a/drivers/usb/cdns3/drd.h b/drivers/usb/cdns3/drd.h
new file mode 100644
index 000000000000..4159e6e612ac
--- /dev/null
+++ b/drivers/usb/cdns3/drd.h
@@ -0,0 +1,129 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Cadence USB3 DRD header file.
+ *
+ * Copyright (C) 2018 Cadence.
+ *
+ * Author: Pawel Laszczak <[email protected]>
+ */
+#ifndef __LINUX_CDNS3_DRD
+#define __LINUX_CDNS3_DRD
+
+#include <linux/usb/otg.h>
+#include <linux/phy/phy.h>
+#include "core.h"
+
+/* DRD register interface. */
+struct cdns3_otg_regs {
+ __le32 did;
+ __le32 rid;
+ __le32 capabilities;
+ __le32 reserved1;
+ __le32 cmd;
+ __le32 sts;
+ __le32 state;
+ __le32 reserved2;
+ __le32 ien;
+ __le32 ivect;
+ __le32 refclk;
+ __le32 tmr;
+ __le32 reserved3[4];
+ __le32 simulate;
+ __le32 override;
+ __le32 susp_ctrl;
+ __le32 reserved4;
+ __le32 anasts;
+ __le32 adp_ramp_time;
+ __le32 ctrl1;
+ __le32 ctrl2;
+};
+
+/* CDNS_RID - bitmasks */
+#define CDNS_RID(p) ((p) & GENMASK(15, 0))
+
+/* CDNS_VID - bitmasks */
+#define CDNS_DID(p) ((p) & GENMASK(31, 0))
+
+/* OTGCMD - bitmasks */
+/* "Request the bus for Device mode. */
+#define OTGCMD_DEV_BUS_REQ BIT(0)
+/* Request the bus for Host mode */
+#define OTGCMD_HOST_BUS_REQ BIT(1)
+/* Enable OTG mode. */
+#define OTGCMD_OTG_EN BIT(2)
+/* Disable OTG mode */
+#define OTGCMD_OTG_DIS BIT(3)
+/*"Configure OTG as A-Device. */
+#define OTGCMD_A_DEV_EN BIT(4)
+/*"Configure OTG as A-Device. */
+#define OTGCMD_A_DEV_DIS BIT(5)
+/* Drop the bus for Device mod e. */
+#define OTGCMD_DEV_BUS_DROP BIT(8)
+/* Drop the bus for Host mode*/
+#define OTGCMD_HOST_BUS_DROP BIT(9)
+/* Power Down USBSS-DEV. */
+#define OTGCMD_DEV_POWER_OFF BIT(11)
+/* Power Down CDNSXHCI. */
+#define OTGCMD_HOST_POWER_OFF BIT(12)
+
+/* OTGIEN - bitmasks */
+/* ID change interrupt enable */
+#define OTGIEN_ID_CHANGE_INT BIT(0)
+/* Vbusvalid fall detected interrupt enable.*/
+#define OTGIEN_VBUSVALID_RISE_INT BIT(4)
+/* Vbusvalid fall detected interrupt enable */
+#define OTGIEN_VBUSVALID_FALL_INT BIT(5)
+
+/* OTGSTS - bitmasks */
+/*
+ * Current value of the ID pin. It is only valid when idpullup in
+ * OTGCTRL1_TYPE register is set to '1'.
+ */
+#define OTGSTS_ID_VALUE BIT(0)
+/* Current value of the vbus_valid */
+#define OTGSTS_VBUS_VALID BIT(1)
+/* Current value of the b_sess_vld */
+#define OTGSTS_SESSION_VALID BIT(2)
+/*Device mode is active*/
+#define OTGSTS_DEV_ACTIVE BIT(3)
+/* Host mode is active. */
+#define OTGSTS_HOST_ACTIVE BIT(4)
+/* OTG Controller not ready. */
+#define OTGSTS_OTG_NRDY_MASK BIT(11)
+#define OTGSTS_OTG_NRDY(p) ((p) & OTGSTS_OTG_NRDY_MASK)
+/*
+ * Value of the strap pins.
+ * 000 - no default configuration
+ * 010 - Controller initiall configured as Host
+ * 100 - Controller initially configured as Device
+ */
+#define OTGSTS_STRAP(p) (((p) & GENMASK(14, 12)) >> 12)
+#define OTGSTS_STRAP_NO_DEFAULT_CFG 0x00
+#define OTGSTS_STRAP_HOST_OTG 0x01
+#define OTGSTS_STRAP_HOST 0x02
+#define OTGSTS_STRAP_GADGET 0x04
+/* Host mode is turned on. */
+#define OTGSTS_XHCI_READY BIT(26)
+/* "Device mode is turned on .*/
+#define OTGSTS_DEV_READY BIT(27)
+
+/* OTGSTATE- bitmasks */
+#define OTGSTATE_HOST_STATE_MASK GENMASK(5, 3)
+#define OTGSTATE_HOST_STATE_IDLE 0x0
+#define OTGSTATE_HOST_STATE_VBUS_FALL 0x7
+#define OTGSTATE_HOST_STATE(p) (((p) & OTGSTATE_HOST_STATE_MASK) >> 3)
+
+/* OTGREFCLK - bitmasks */
+#define OTGREFCLK_STB_CLK_SWITCH_EN BIT(31)
+
+/* OVERRIDE - bitmasks */
+#define OVERRIDE_IDPULLUP BIT(0)
+
+int cdns3_is_host(struct cdns3 *cdns);
+int cdns3_is_device(struct cdns3 *cdns);
+int cdns3_get_id(struct cdns3 *cdns);
+int cdns3_drd_init(struct cdns3 *cdns);
+int cdns3_drd_exit(struct cdns3 *cdns);
+int cdns3_drd_update_mode(struct cdns3 *cdns);
+
+#endif /* __LINUX_CDNS3_DRD */
diff --git a/drivers/usb/cdns3/ep0.c b/drivers/usb/cdns3/ep0.c
new file mode 100644
index 000000000000..1ef0e9f73e3e
--- /dev/null
+++ b/drivers/usb/cdns3/ep0.c
@@ -0,0 +1,864 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Cadence USBSS DRD Driver - gadget side.
+ *
+ * Copyright (C) 2018 Cadence Design Systems.
+ * Copyright (C) 2017-2018 NXP
+ *
+ * Authors: Pawel Jez <[email protected]>,
+ * Pawel Laszczak <[email protected]>
+ * Peter Chen <[email protected]>
+ */
+
+#include <linux/usb/composite.h>
+
+#include "gadget.h"
+#include "trace.h"
+
+static struct usb_endpoint_descriptor cdns3_gadget_ep0_desc = {
+ .bLength = USB_DT_ENDPOINT_SIZE,
+ .bDescriptorType = USB_DT_ENDPOINT,
+ .bmAttributes = USB_ENDPOINT_XFER_CONTROL,
+};
+
+/**
+ * cdns3_ep0_run_transfer - Do transfer on default endpoint hardware
+ * @priv_dev: extended gadget object
+ * @dma_addr: physical address where data is/will be stored
+ * @length: data length
+ * @erdy: set it to 1 when ERDY packet should be sent -
+ * exit from flow control state
+ */
+static void cdns3_ep0_run_transfer(struct cdns3_device *priv_dev,
+ dma_addr_t dma_addr,
+ unsigned int length, int erdy)
+{
+ struct cdns3_usb_regs __iomem *regs = priv_dev->regs;
+ struct cdns3_endpoint *priv_ep = ep_to_cdns3_ep(priv_dev->gadget.ep0);
+
+ priv_dev->ep0_trb->buffer = TRB_BUFFER(dma_addr);
+ priv_dev->ep0_trb->length = TRB_LEN(length);
+ priv_dev->ep0_trb->control = TRB_CYCLE | TRB_IOC | TRB_TYPE(TRB_NORMAL);
+
+ trace_cdns3_prepare_trb(priv_ep, priv_dev->ep0_trb);
+
+ cdns3_select_ep(priv_dev, priv_dev->ep0_data_dir);
+
+ writel(EP_STS_TRBERR, &regs->ep_sts);
+ writel(EP_TRADDR_TRADDR(priv_dev->ep0_trb_dma), &regs->ep_traddr);
+ trace_cdns3_doorbell_ep0(priv_dev->ep0_data_dir ? "ep0in" : "ep0out");
+
+ /* TRB should be prepared before starting transfer */
+ writel(EP_CMD_DRDY, &regs->ep_cmd);
+
+ if (erdy)
+ writel(EP_CMD_ERDY, &priv_dev->regs->ep_cmd);
+}
+
+/**
+ * cdns3_ep0_delegate_req - Returns status of handling setup packet
+ * Setup is handled by gadget driver
+ * @priv_dev: extended gadget object
+ * @ctrl_req: pointer to received setup packet
+ *
+ * Returns zero on success or negative value on failure
+ */
+static int cdns3_ep0_delegate_req(struct cdns3_device *priv_dev,
+ struct usb_ctrlrequest *ctrl_req)
+{
+ int ret;
+
+ spin_unlock(&priv_dev->lock);
+ priv_dev->setup_pending = 1;
+ ret = priv_dev->gadget_driver->setup(&priv_dev->gadget, ctrl_req);
+ priv_dev->setup_pending = 0;
+ spin_lock(&priv_dev->lock);
+ return ret;
+}
+
+static void cdns3_prepare_setup_packet(struct cdns3_device *priv_dev)
+{
+ priv_dev->ep0_data_dir = 0;
+ cdns3_ep0_run_transfer(priv_dev, priv_dev->setup_dma,
+ sizeof(struct usb_ctrlrequest), 0);
+}
+
+/**
+ * cdns3_req_ep0_set_configuration - Handling of SET_CONFIG standard USB request
+ * @priv_dev: extended gadget object
+ * @ctrl_req: pointer to received setup packet
+ *
+ * Returns 0 if success, USB_GADGET_DELAYED_STATUS on deferred status stage,
+ * error code on error
+ */
+static int cdns3_req_ep0_set_configuration(struct cdns3_device *priv_dev,
+ struct usb_ctrlrequest *ctrl_req)
+{
+ enum usb_device_state device_state = priv_dev->gadget.state;
+ struct cdns3_endpoint *priv_ep;
+ u32 config = le16_to_cpu(ctrl_req->wValue);
+ int result = 0;
+ int i;
+
+ switch (device_state) {
+ case USB_STATE_ADDRESS:
+ /* Configure non-control EPs */
+ for (i = 0; i < CDNS3_ENDPOINTS_MAX_COUNT; i++) {
+ priv_ep = priv_dev->eps[i];
+ if (!priv_ep)
+ continue;
+
+ if (priv_ep->flags & EP_CLAIMED)
+ cdns3_ep_config(priv_ep);
+ }
+
+ result = cdns3_ep0_delegate_req(priv_dev, ctrl_req);
+
+ if (result)
+ return result;
+
+ if (config) {
+ cdns3_set_hw_configuration(priv_dev);
+ } else {
+ cdns3_gadget_unconfig(priv_dev);
+ usb_gadget_set_state(&priv_dev->gadget,
+ USB_STATE_ADDRESS);
+ }
+ break;
+ case USB_STATE_CONFIGURED:
+ result = cdns3_ep0_delegate_req(priv_dev, ctrl_req);
+
+ if (!config && !result) {
+ cdns3_gadget_unconfig(priv_dev);
+ usb_gadget_set_state(&priv_dev->gadget,
+ USB_STATE_ADDRESS);
+ }
+ break;
+ default:
+ result = -EINVAL;
+ }
+
+ return result;
+}
+
+/**
+ * cdns3_req_ep0_set_address - Handling of SET_ADDRESS standard USB request
+ * @priv_dev: extended gadget object
+ * @ctrl_req: pointer to received setup packet
+ *
+ * Returns 0 if success, error code on error
+ */
+static int cdns3_req_ep0_set_address(struct cdns3_device *priv_dev,
+ struct usb_ctrlrequest *ctrl_req)
+{
+ enum usb_device_state device_state = priv_dev->gadget.state;
+ u32 reg;
+ u32 addr;
+
+ addr = le16_to_cpu(ctrl_req->wValue);
+
+ if (addr > USB_DEVICE_MAX_ADDRESS) {
+ dev_err(priv_dev->dev,
+ "Device address (%d) cannot be greater than %d\n",
+ addr, USB_DEVICE_MAX_ADDRESS);
+ return -EINVAL;
+ }
+
+ if (device_state == USB_STATE_CONFIGURED) {
+ dev_err(priv_dev->dev,
+ "can't set_address from configured state\n");
+ return -EINVAL;
+ }
+
+ reg = readl(&priv_dev->regs->usb_cmd);
+
+ writel(reg | USB_CMD_FADDR(addr) | USB_CMD_SET_ADDR,
+ &priv_dev->regs->usb_cmd);
+
+ usb_gadget_set_state(&priv_dev->gadget,
+ (addr ? USB_STATE_ADDRESS : USB_STATE_DEFAULT));
+
+ cdns3_prepare_setup_packet(priv_dev);
+
+ writel(EP_CMD_ERDY | EP_CMD_REQ_CMPL, &priv_dev->regs->ep_cmd);
+
+ return 0;
+}
+
+/**
+ * cdns3_req_ep0_get_status - Handling of GET_STATUS standard USB request
+ * @priv_dev: extended gadget object
+ * @ctrl_req: pointer to received setup packet
+ *
+ * Returns 0 if success, error code on error
+ */
+static int cdns3_req_ep0_get_status(struct cdns3_device *priv_dev,
+ struct usb_ctrlrequest *ctrl)
+{
+ __le16 *response_pkt;
+ u16 usb_status = 0;
+ u32 recip;
+ u32 reg;
+
+ recip = ctrl->bRequestType & USB_RECIP_MASK;
+
+ switch (recip) {
+ case USB_RECIP_DEVICE:
+ /* self powered */
+ if (priv_dev->is_selfpowered)
+ usb_status = BIT(USB_DEVICE_SELF_POWERED);
+
+ if (priv_dev->wake_up_flag)
+ usb_status |= BIT(USB_DEVICE_REMOTE_WAKEUP);
+
+ if (priv_dev->gadget.speed != USB_SPEED_SUPER)
+ break;
+
+ reg = readl(&priv_dev->regs->usb_sts);
+
+ if (priv_dev->u1_allowed)
+ usb_status |= BIT(USB_DEV_STAT_U1_ENABLED);
+
+ if (priv_dev->u2_allowed)
+ usb_status |= BIT(USB_DEV_STAT_U2_ENABLED);
+
+ break;
+ case USB_RECIP_INTERFACE:
+ return cdns3_ep0_delegate_req(priv_dev, ctrl);
+ case USB_RECIP_ENDPOINT:
+ /* check if endpoint is stalled */
+ cdns3_select_ep(priv_dev, ctrl->wIndex);
+ if (EP_STS_STALL(readl(&priv_dev->regs->ep_sts)))
+ usb_status = BIT(USB_ENDPOINT_HALT);
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ response_pkt = (__le16 *)priv_dev->setup_buf;
+ *response_pkt = cpu_to_le16(usb_status);
+
+ cdns3_ep0_run_transfer(priv_dev, priv_dev->setup_dma,
+ sizeof(*response_pkt), 1);
+ return 0;
+}
+
+static int cdns3_ep0_feature_handle_device(struct cdns3_device *priv_dev,
+ struct usb_ctrlrequest *ctrl,
+ int set)
+{
+ enum usb_device_state state;
+ enum usb_device_speed speed;
+ int ret = 0;
+ u32 wValue;
+ u32 wIndex;
+ u16 tmode;
+
+ wValue = le16_to_cpu(ctrl->wValue);
+ wIndex = le16_to_cpu(ctrl->wIndex);
+ state = priv_dev->gadget.state;
+ speed = priv_dev->gadget.speed;
+
+ switch (ctrl->wValue) {
+ case USB_DEVICE_REMOTE_WAKEUP:
+ priv_dev->wake_up_flag = !!set;
+ break;
+ case USB_DEVICE_U1_ENABLE:
+ if (state != USB_STATE_CONFIGURED || speed != USB_SPEED_SUPER)
+ return -EINVAL;
+
+ priv_dev->u1_allowed = !!set;
+ break;
+ case USB_DEVICE_U2_ENABLE:
+ if (state != USB_STATE_CONFIGURED || speed != USB_SPEED_SUPER)
+ return -EINVAL;
+
+ priv_dev->u2_allowed = !!set;
+ break;
+ case USB_DEVICE_LTM_ENABLE:
+ ret = -EINVAL;
+ break;
+ case USB_DEVICE_TEST_MODE:
+ if (state != USB_STATE_CONFIGURED || speed > USB_SPEED_HIGH)
+ return -EINVAL;
+
+ tmode = le16_to_cpu(ctrl->wIndex);
+
+ if (!set || (tmode & 0xff) != 0)
+ return -EINVAL;
+
+ switch (tmode >> 8) {
+ case TEST_J:
+ case TEST_K:
+ case TEST_SE0_NAK:
+ case TEST_PACKET:
+ cdns3_set_register_bit(&priv_dev->regs->usb_cmd,
+ USB_CMD_STMODE |
+ USB_STS_TMODE_SEL(tmode - 1));
+ break;
+ default:
+ ret = -EINVAL;
+ }
+ break;
+ default:
+ ret = -EINVAL;
+ }
+
+ return ret;
+}
+
+static int cdns3_ep0_feature_handle_intf(struct cdns3_device *priv_dev,
+ struct usb_ctrlrequest *ctrl,
+ int set)
+{
+ u32 wValue;
+ int ret = 0;
+
+ wValue = le16_to_cpu(ctrl->wValue);
+
+ switch (wValue) {
+ case USB_INTRF_FUNC_SUSPEND:
+ break;
+ default:
+ ret = -EINVAL;
+ }
+
+ return ret;
+}
+
+static int cdns3_ep0_feature_handle_endpoint(struct cdns3_device *priv_dev,
+ struct usb_ctrlrequest *ctrl,
+ int set)
+{
+ struct cdns3_endpoint *priv_ep;
+ int ret = 0;
+ u8 index;
+
+ if (le16_to_cpu(ctrl->wValue) != USB_ENDPOINT_HALT)
+ return -EINVAL;
+
+ if (!(ctrl->wIndex & ~USB_DIR_IN))
+ return 0;
+
+ index = cdns3_ep_addr_to_index(ctrl->wIndex);
+ priv_ep = priv_dev->eps[index];
+
+ cdns3_select_ep(priv_dev, ctrl->wIndex);
+
+ if (set) {
+ writel(EP_CMD_SSTALL, &priv_dev->regs->ep_cmd);
+ priv_ep->flags |= EP_STALL;
+ } else {
+ struct usb_request *request;
+
+ if (priv_dev->eps[index]->flags & EP_WEDGE) {
+ cdns3_select_ep(priv_dev, 0x00);
+ return 0;
+ }
+
+ writel(EP_CMD_CSTALL | EP_CMD_EPRST, &priv_dev->regs->ep_cmd);
+
+ /* wait for EPRST cleared */
+ ret = cdns3_handshake(&priv_dev->regs->ep_cmd,
+ EP_CMD_EPRST, 0, 100);
+ if (ret)
+ return -EINVAL;
+
+ priv_ep->flags &= ~EP_STALL;
+
+ request = cdns3_next_request(&priv_ep->request_list);
+ if (request)
+ cdns3_ep_run_transfer(priv_ep, request);
+ }
+ return ret;
+}
+
+/**
+ * cdns3_req_ep0_handle_feature -
+ * Handling of GET/SET_FEATURE standard USB request
+ *
+ * @priv_dev: extended gadget object
+ * @ctrl_req: pointer to received setup packet
+ * @set: must be set to 1 for SET_FEATURE request
+ *
+ * Returns 0 if success, error code on error
+ */
+static int cdns3_req_ep0_handle_feature(struct cdns3_device *priv_dev,
+ struct usb_ctrlrequest *ctrl,
+ int set)
+{
+ int ret = 0;
+ u32 recip;
+
+ recip = ctrl->bRequestType & USB_RECIP_MASK;
+
+ switch (recip) {
+ case USB_RECIP_DEVICE:
+ ret = cdns3_ep0_feature_handle_device(priv_dev, ctrl, set);
+ break;
+ case USB_RECIP_INTERFACE:
+ ret = cdns3_ep0_feature_handle_intf(priv_dev, ctrl, set);
+ break;
+ case USB_RECIP_ENDPOINT:
+ ret = cdns3_ep0_feature_handle_endpoint(priv_dev, ctrl, set);
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ if (!ret)
+ writel(EP_CMD_ERDY | EP_CMD_REQ_CMPL, &priv_dev->regs->ep_cmd);
+
+ return ret;
+}
+
+/**
+ * cdns3_req_ep0_set_sel - Handling of SET_SEL standard USB request
+ * @priv_dev: extended gadget object
+ * @ctrl_req: pointer to received setup packet
+ *
+ * Returns 0 if success, error code on error
+ */
+static int cdns3_req_ep0_set_sel(struct cdns3_device *priv_dev,
+ struct usb_ctrlrequest *ctrl_req)
+{
+ if (priv_dev->gadget.state < USB_STATE_ADDRESS)
+ return -EINVAL;
+
+ if (ctrl_req->wLength != 6) {
+ dev_err(priv_dev->dev, "Set SEL should be 6 bytes, got %d\n",
+ ctrl_req->wLength);
+ return -EINVAL;
+ }
+
+ cdns3_ep0_run_transfer(priv_dev, priv_dev->setup_dma, 6, 1);
+ return 0;
+}
+
+/**
+ * cdns3_req_ep0_set_isoch_delay -
+ * Handling of GET_ISOCH_DELAY standard USB request
+ * @priv_dev: extended gadget object
+ * @ctrl_req: pointer to received setup packet
+ *
+ * Returns 0 if success, error code on error
+ */
+static int cdns3_req_ep0_set_isoch_delay(struct cdns3_device *priv_dev,
+ struct usb_ctrlrequest *ctrl_req)
+{
+ if (ctrl_req->wIndex || ctrl_req->wLength)
+ return -EINVAL;
+
+ priv_dev->isoch_delay = ctrl_req->wValue;
+ writel(EP_CMD_ERDY | EP_CMD_REQ_CMPL, &priv_dev->regs->ep_cmd);
+ return 0;
+}
+
+/**
+ * cdns3_ep0_standard_request - Handling standard USB requests
+ * @priv_dev: extended gadget object
+ * @ctrl_req: pointer to received setup packet
+ *
+ * Returns 0 if success, error code on error
+ */
+static int cdns3_ep0_standard_request(struct cdns3_device *priv_dev,
+ struct usb_ctrlrequest *ctrl_req)
+{
+ int ret;
+
+ switch (ctrl_req->bRequest) {
+ case USB_REQ_SET_ADDRESS:
+ ret = cdns3_req_ep0_set_address(priv_dev, ctrl_req);
+ break;
+ case USB_REQ_SET_CONFIGURATION:
+ ret = cdns3_req_ep0_set_configuration(priv_dev, ctrl_req);
+ break;
+ case USB_REQ_GET_STATUS:
+ ret = cdns3_req_ep0_get_status(priv_dev, ctrl_req);
+ break;
+ case USB_REQ_CLEAR_FEATURE:
+ ret = cdns3_req_ep0_handle_feature(priv_dev, ctrl_req, 0);
+ break;
+ case USB_REQ_SET_FEATURE:
+ ret = cdns3_req_ep0_handle_feature(priv_dev, ctrl_req, 1);
+ break;
+ case USB_REQ_SET_SEL:
+ ret = cdns3_req_ep0_set_sel(priv_dev, ctrl_req);
+ break;
+ case USB_REQ_SET_ISOCH_DELAY:
+ ret = cdns3_req_ep0_set_isoch_delay(priv_dev, ctrl_req);
+ break;
+ default:
+ ret = cdns3_ep0_delegate_req(priv_dev, ctrl_req);
+ break;
+ }
+
+ return ret;
+}
+
+static void __pending_setup_status_handler(struct cdns3_device *priv_dev)
+{
+ struct usb_request *request = priv_dev->pending_status_request;
+
+ if (priv_dev->status_completion_no_call && request &&
+ request->complete) {
+ request->complete(priv_dev->gadget.ep0, request);
+ priv_dev->status_completion_no_call = 0;
+ }
+}
+
+void cdns3_pending_setup_status_handler(struct work_struct *work)
+{
+ struct cdns3_device *priv_dev = container_of(work, struct cdns3_device,
+ pending_status_wq);
+ unsigned long flags;
+
+ spin_lock_irqsave(&priv_dev->lock, flags);
+ __pending_setup_status_handler(priv_dev);
+ spin_unlock_irqrestore(&priv_dev->lock, flags);
+}
+
+/**
+ * cdns3_gadget_ep_giveback - call struct usb_request's ->complete callback
+ * @priv_ep: The endpoint to whom the request belongs to
+ * @priv_req: The request we're giving back
+ * @status: completion code for the request
+ *
+ * Must be called with controller's lock held and interrupts disabled. This
+ * function will unmap @req and call its ->complete() callback to notify upper
+ * layers that it has completed.
+ */
+
+void cdns3_gadget_ep0_giveback(struct cdns3_device *priv_dev,
+ int status)
+{
+ struct cdns3_endpoint *priv_ep;
+ struct usb_request *request;
+
+ priv_ep = ep_to_cdns3_ep(priv_dev->gadget.ep0);
+ request = cdns3_next_request(&priv_ep->request_list);
+
+ priv_ep->dir = priv_dev->ep0_data_dir;
+ cdns3_gadget_giveback(priv_ep, to_cdns3_request(request), status);
+ priv_dev->ep0_request = NULL;
+}
+
+/**
+ * cdns3_ep0_setup_phase - Handling setup USB requests
+ * @priv_dev: extended gadget object
+ */
+static void cdns3_ep0_setup_phase(struct cdns3_device *priv_dev)
+{
+ struct usb_ctrlrequest *ctrl = priv_dev->setup_buf;
+ struct cdns3_endpoint *priv_ep;
+ int result;
+
+ priv_dev->ep0_data_dir = ctrl->bRequestType & USB_DIR_IN;
+ priv_ep = ep_to_cdns3_ep(priv_dev->gadget.ep0);
+
+ trace_cdns3_ctrl_req(ctrl);
+
+ if (!list_empty(&priv_ep->request_list))
+ cdns3_gadget_ep0_giveback(priv_dev, -ECONNRESET);
+
+ if ((ctrl->bRequestType & USB_TYPE_MASK) == USB_TYPE_STANDARD)
+ result = cdns3_ep0_standard_request(priv_dev, ctrl);
+ else
+ result = cdns3_ep0_delegate_req(priv_dev, ctrl);
+
+ if (result != 0 && result != USB_GADGET_DELAYED_STATUS) {
+ dev_dbg(priv_dev->dev, "STALL for ep0\n");
+ /* set_stall on ep0 */
+ cdns3_select_ep(priv_dev, 0x00);
+ writel(EP_CMD_SSTALL, &priv_dev->regs->ep_cmd);
+ writel(EP_CMD_ERDY | EP_CMD_REQ_CMPL, &priv_dev->regs->ep_cmd);
+ }
+}
+
+static void cdns3_transfer_completed(struct cdns3_device *priv_dev)
+{
+ struct cdns3_endpoint *priv_ep = ep_to_cdns3_ep(priv_dev->gadget.ep0);
+
+ if (priv_dev->ep0_request) {
+ trace_cdns3_complete_trb(priv_ep, priv_dev->ep0_trb);
+
+ priv_dev->ep0_request->actual =
+ TRB_LEN(le32_to_cpu(priv_dev->ep0_trb->length));
+
+ cdns3_gadget_ep0_giveback(priv_dev, 0);
+ }
+
+ cdns3_prepare_setup_packet(priv_dev);
+ writel(EP_CMD_REQ_CMPL, &priv_dev->regs->ep_cmd);
+}
+
+/**
+ * cdns3_check_new_setup - Check if controller receive new SETUP packet.
+ * @priv_dev: extended gadget object
+ *
+ * The SETUP packet can be kept in on-chip memory or in system memory.
+ */
+static bool cdns3_check_new_setup(struct cdns3_device *priv_dev)
+{
+ u32 ep_sts_reg;
+
+ cdns3_select_ep(priv_dev, 0 | USB_DIR_OUT);
+ ep_sts_reg = readl(&priv_dev->regs->ep_sts);
+
+ return !!(ep_sts_reg & (EP_STS_SETUP | EP_STS_STPWAIT));
+}
+
+/**
+ * cdns3_check_ep0_interrupt_proceed - Processes interrupt related to endpoint 0
+ * @priv_dev: extended gadget object
+ * @dir: USB_DIR_IN for IN direction, USB_DIR_OUT for OUT direction
+ */
+void cdns3_check_ep0_interrupt_proceed(struct cdns3_device *priv_dev, int dir)
+{
+ u32 ep_sts_reg;
+
+ cdns3_select_ep(priv_dev, dir);
+
+ ep_sts_reg = readl(&priv_dev->regs->ep_sts);
+ writel(ep_sts_reg, &priv_dev->regs->ep_sts);
+
+ trace_cdns3_ep0_irq(priv_dev);
+
+ __pending_setup_status_handler(priv_dev);
+
+ if ((ep_sts_reg & EP_STS_SETUP)) {
+ cdns3_ep0_setup_phase(priv_dev);
+ } else if ((ep_sts_reg & EP_STS_IOC) || (ep_sts_reg & EP_STS_ISP)) {
+ priv_dev->ep0_data_dir = dir;
+ cdns3_transfer_completed(priv_dev);
+ }
+
+ if (ep_sts_reg & EP_STS_DESCMIS) {
+ if (dir == 0 && !priv_dev->setup_pending)
+ cdns3_prepare_setup_packet(priv_dev);
+ }
+}
+
+/**
+ * cdns3_gadget_ep0_enable
+ * Function shouldn't be called by gadget driver,
+ * endpoint 0 is allways active
+ */
+static int cdns3_gadget_ep0_enable(struct usb_ep *ep,
+ const struct usb_endpoint_descriptor *desc)
+{
+ return -EINVAL;
+}
+
+/**
+ * cdns3_gadget_ep0_disable
+ * Function shouldn't be called by gadget driver,
+ * endpoint 0 is allways active
+ */
+static int cdns3_gadget_ep0_disable(struct usb_ep *ep)
+{
+ return -EINVAL;
+}
+
+/**
+ * cdns3_gadget_ep0_set_halt
+ * @ep: pointer to endpoint zero object
+ * @value: 1 for set stall, 0 for clear stall
+ *
+ * Returns 0
+ */
+static int cdns3_gadget_ep0_set_halt(struct usb_ep *ep, int value)
+{
+ /* TODO */
+ return 0;
+}
+
+/**
+ * cdns3_gadget_ep0_queue Transfer data on endpoint zero
+ * @ep: pointer to endpoint zero object
+ * @request: pointer to request object
+ * @gfp_flags: gfp flags
+ *
+ * Returns 0 on success, error code elsewhere
+ */
+static int cdns3_gadget_ep0_queue(struct usb_ep *ep,
+ struct usb_request *request,
+ gfp_t gfp_flags)
+{
+ struct cdns3_endpoint *priv_ep = ep_to_cdns3_ep(ep);
+ struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
+ unsigned long flags;
+ int erdy_sent = 0;
+ int ret = 0;
+
+ dev_dbg(priv_dev->dev, "Queue to Ep0%s L: %d\n",
+ priv_dev->ep0_data_dir ? "IN" : "OUT",
+ request->length);
+
+ /* cancel the request if controller receive new SETUP packet. */
+ if (cdns3_check_new_setup(priv_dev))
+ return -ECONNRESET;
+
+ /* send STATUS stage. Should be called only for SET_CONFIGURATION */
+ if (request->length == 0 && request->zero == 0) {
+ spin_lock_irqsave(&priv_dev->lock, flags);
+ cdns3_select_ep(priv_dev, 0x00);
+
+ erdy_sent = !priv_dev->hw_configured_flag;
+ cdns3_set_hw_configuration(priv_dev);
+
+ if (!erdy_sent)
+ writel(EP_CMD_ERDY | EP_CMD_REQ_CMPL,
+ &priv_dev->regs->ep_cmd);
+
+ cdns3_prepare_setup_packet(priv_dev);
+ request->actual = 0;
+ priv_dev->status_completion_no_call = true;
+ priv_dev->pending_status_request = request;
+ spin_unlock_irqrestore(&priv_dev->lock, flags);
+
+ /*
+ * Since there is no completion interrupt for status stage,
+ * it needs to call ->completion in software after
+ * ep0_queue is back.
+ */
+ queue_work(system_freezable_wq, &priv_dev->pending_status_wq);
+ return 0;
+ }
+
+ spin_lock_irqsave(&priv_dev->lock, flags);
+ if (!list_empty(&priv_ep->request_list)) {
+ dev_err(priv_dev->dev,
+ "can't handle multiple requests for ep0\n");
+ spin_unlock_irqrestore(&priv_dev->lock, flags);
+ return -EBUSY;
+ }
+
+ ret = usb_gadget_map_request_by_dev(priv_dev->sysdev, request,
+ priv_dev->ep0_data_dir);
+ if (ret) {
+ spin_unlock_irqrestore(&priv_dev->lock, flags);
+ dev_err(priv_dev->dev, "failed to map request\n");
+ return -EINVAL;
+ }
+
+ request->status = -EINPROGRESS;
+ priv_dev->ep0_request = request;
+ list_add_tail(&request->list, &priv_ep->request_list);
+ cdns3_ep0_run_transfer(priv_dev, request->dma, request->length, 1);
+ spin_unlock_irqrestore(&priv_dev->lock, flags);
+
+ return ret;
+}
+
+/**
+ * cdns3_gadget_ep_set_wedge Set wedge on selected endpoint
+ * @ep: endpoint object
+ *
+ * Returns 0
+ */
+int cdns3_gadget_ep_set_wedge(struct usb_ep *ep)
+{
+ struct cdns3_endpoint *priv_ep = ep_to_cdns3_ep(ep);
+ struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
+
+ dev_dbg(priv_dev->dev, "Wedge for %s\n", ep->name);
+ cdns3_gadget_ep_set_halt(ep, 1);
+ priv_ep->flags |= EP_WEDGE;
+
+ return 0;
+}
+
+const struct usb_ep_ops cdns3_gadget_ep0_ops = {
+ .enable = cdns3_gadget_ep0_enable,
+ .disable = cdns3_gadget_ep0_disable,
+ .alloc_request = cdns3_gadget_ep_alloc_request,
+ .free_request = cdns3_gadget_ep_free_request,
+ .queue = cdns3_gadget_ep0_queue,
+ .dequeue = cdns3_gadget_ep_dequeue,
+ .set_halt = cdns3_gadget_ep0_set_halt,
+ .set_wedge = cdns3_gadget_ep_set_wedge,
+};
+
+/**
+ * cdns3_ep0_config - Configures default endpoint
+ * @priv_dev: extended gadget object
+ *
+ * Functions sets parameters: maximal packet size and enables interrupts
+ */
+void cdns3_ep0_config(struct cdns3_device *priv_dev)
+{
+ struct cdns3_usb_regs __iomem *regs;
+ u32 max_packet_size = 64;
+
+ regs = priv_dev->regs;
+
+ if (priv_dev->gadget.speed == USB_SPEED_SUPER)
+ max_packet_size = 512;
+
+ if (priv_dev->ep0_request) {
+ list_del_init(&priv_dev->ep0_request->list);
+ priv_dev->ep0_request = NULL;
+ }
+
+ priv_dev->u1_allowed = 0;
+ priv_dev->u2_allowed = 0;
+
+ priv_dev->gadget.ep0->maxpacket = max_packet_size;
+ cdns3_gadget_ep0_desc.wMaxPacketSize = cpu_to_le16(max_packet_size);
+
+ /* init ep out */
+ cdns3_select_ep(priv_dev, USB_DIR_OUT);
+
+ writel(EP_CFG_ENABLE | EP_CFG_MAXPKTSIZE(max_packet_size),
+ &regs->ep_cfg);
+
+ writel(EP_STS_EN_SETUPEN | EP_STS_EN_DESCMISEN | EP_STS_EN_TRBERREN,
+ &regs->ep_sts_en);
+
+ /* init ep in */
+ cdns3_select_ep(priv_dev, USB_DIR_IN);
+
+ writel(EP_CFG_ENABLE | EP_CFG_MAXPKTSIZE(max_packet_size),
+ &regs->ep_cfg);
+
+ writel(EP_STS_EN_SETUPEN | EP_STS_EN_TRBERREN, &regs->ep_sts_en);
+
+ cdns3_set_register_bit(&regs->usb_conf, USB_CONF_U1DS | USB_CONF_U2DS);
+ cdns3_prepare_setup_packet(priv_dev);
+}
+
+/**
+ * cdns3_init_ep0 Initializes software endpoint 0 of gadget
+ * @cdns3: extended gadget object
+ *
+ * Returns 0 on success, error code elsewhere
+ */
+int cdns3_init_ep0(struct cdns3_device *priv_dev)
+{
+ struct cdns3_endpoint *ep0;
+
+ ep0 = devm_kzalloc(priv_dev->dev, sizeof(struct cdns3_endpoint),
+ GFP_KERNEL);
+
+ if (!ep0)
+ return -ENOMEM;
+
+ ep0->cdns3_dev = priv_dev;
+ sprintf(ep0->name, "ep0");
+
+ /* fill linux fields */
+ ep0->endpoint.ops = &cdns3_gadget_ep0_ops;
+ ep0->endpoint.maxburst = 1;
+ usb_ep_set_maxpacket_limit(&ep0->endpoint, CDNS3_EP0_MAX_PACKET_LIMIT);
+ ep0->endpoint.address = 0;
+ ep0->endpoint.caps.type_control = 1;
+ ep0->endpoint.caps.dir_in = 1;
+ ep0->endpoint.caps.dir_out = 1;
+ ep0->endpoint.name = ep0->name;
+ ep0->endpoint.desc = &cdns3_gadget_ep0_desc;
+ priv_dev->gadget.ep0 = &ep0->endpoint;
+ INIT_LIST_HEAD(&ep0->request_list);
+
+ return 0;
+}
diff --git a/drivers/usb/cdns3/gadget-export.h b/drivers/usb/cdns3/gadget-export.h
new file mode 100644
index 000000000000..577469eee961
--- /dev/null
+++ b/drivers/usb/cdns3/gadget-export.h
@@ -0,0 +1,28 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Cadence USBSS DRD Driver - Gadget Export APIs.
+ *
+ * Copyright (C) 2017 NXP
+ * Copyright (C) 2017-2018 NXP
+ *
+ * Authors: Peter Chen <[email protected]>
+ */
+#ifndef __LINUX_CDNS3_GADGET_EXPORT
+#define __LINUX_CDNS3_GADGET_EXPORT
+
+#ifdef CONFIG_USB_CDNS3_GADGET
+
+int cdns3_gadget_init(struct cdns3 *cdns);
+void cdns3_gadget_exit(struct cdns3 *cdns);
+#else
+
+static inline int cdns3_gadget_init(struct cdns3 *cdns)
+{
+ return -ENXIO;
+}
+
+static inline void cdns3_gadget_exit(struct cdns3 *cdns) { }
+
+#endif
+
+#endif /* __LINUX_CDNS3_GADGET_EXPORT */
diff --git a/drivers/usb/cdns3/gadget.c b/drivers/usb/cdns3/gadget.c
new file mode 100644
index 000000000000..a021eaf07aee
--- /dev/null
+++ b/drivers/usb/cdns3/gadget.c
@@ -0,0 +1,1802 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Cadence USBSS DRD Driver - gadget side.
+ *
+ * Copyright (C) 2018 Cadence Design Systems.
+ * Copyright (C) 2017-2018 NXP
+ *
+ * Authors: Pawel Jez <[email protected]>,
+ * Pawel Laszczak <[email protected]>
+ * Peter Chen <[email protected]>
+ */
+
+#include <linux/dma-mapping.h>
+#include <linux/usb/gadget.h>
+
+#include "core.h"
+#include "gadget-export.h"
+#include "gadget.h"
+
+#include "trace.h"
+
+static int __cdns3_gadget_ep_queue(struct usb_ep *ep,
+ struct usb_request *request,
+ gfp_t gfp_flags);
+
+/**
+ * cdns3_handshake - spin reading until handshake completes or fails
+ * @ptr: address of device controller register to be read
+ * @mask: bits to look at in result of read
+ * @done: value of those bits when handshake succeeds
+ * @usec: timeout in microseconds
+ *
+ * Returns negative errno, or zero on success
+ *
+ * Success happens when the "mask" bits have the specified value (hardware
+ * handshake done). There are two failure modes: "usec" have passed (major
+ * hardware flakeout), or the register reads as all-ones (hardware removed).
+ */
+int cdns3_handshake(void __iomem *ptr, u32 mask, u32 done, int usec)
+{
+ u32 result;
+
+ do {
+ result = readl(ptr);
+ if (result == ~(u32)0) /* card removed */
+ return -ENODEV;
+ result &= mask;
+ if (result == done)
+ return 0;
+ udelay(1);
+ usec--;
+ } while (usec > 0);
+ return -ETIMEDOUT;
+}
+
+/**
+ * cdns3_set_register_bit - set bit in given register.
+ * @ptr: address of device controller register to be read and changed
+ * @mask: bits requested to set
+ */
+void cdns3_set_register_bit(void __iomem *ptr, u32 mask)
+{
+ mask = readl(ptr) | mask;
+ writel(mask, ptr);
+}
+
+/**
+ * cdns3_ep_reg_pos_to_index - Macro converts bit position of ep_ists register
+ * to index of endpoint object in cdns3_device.eps[] container
+ * @i: bit position of endpoint for which endpoint object is required
+ *
+ * Remember that endpoint container doesn't contain default endpoint
+ */
+static u8 cdns3_ep_reg_pos_to_index(int i)
+{
+ return ((i / 16) + (((i % 16) - 2) * 2));
+}
+
+/**
+ * cdns3_ep_addr_to_index - Macro converts endpoint address to
+ * index of endpoint object in cdns3_device.eps[] container
+ * @ep_addr: endpoint address for which endpoint object is required
+ *
+ * Remember that endpoint container doesn't contain default endpoint
+ */
+u8 cdns3_ep_addr_to_index(u8 ep_addr)
+{
+ return (((ep_addr & 0x7F) - 1) + ((ep_addr & USB_DIR_IN) ? 1 : 0));
+}
+
+/**
+ * cdns3_ep_addr_to_bit_pos - Macro converts endpoint address to
+ * bit position in ep_ists register
+ * @ep_addr: endpoint address for which bit position is required
+ *
+ * Remember that endpoint container doesn't contain default endpoint
+ */
+static u32 cdns3_ep_addr_to_bit_pos(u8 ep_addr)
+{
+ return (1 << (ep_addr & 0x7F)) << ((ep_addr & 0x80) ? 16 : 0);
+}
+
+/**
+ * cdns3_next_request - returns next request from list
+ * @list: list containing requests
+ *
+ * Returns request or NULL if no requests in list
+ */
+struct usb_request *cdns3_next_request(struct list_head *list)
+{
+ if (list_empty(list))
+ return NULL;
+ return list_first_entry(list, struct usb_request, list);
+}
+
+/**
+ * select_ep - selects endpoint
+ * @priv_dev: extended gadget object
+ * @ep: endpoint address
+ */
+void cdns3_select_ep(struct cdns3_device *priv_dev, u32 ep)
+{
+ if (priv_dev->selected_ep == ep)
+ return;
+
+ priv_dev->selected_ep = ep;
+ writel(ep, &priv_dev->regs->ep_sel);
+}
+
+dma_addr_t cdns3_trb_virt_to_dma(struct cdns3_endpoint *priv_ep,
+ struct cdns3_trb *trb)
+{
+ u32 offset = (char *)trb - (char *)priv_ep->trb_pool;
+
+ return priv_ep->trb_pool_dma + offset;
+}
+
+/**
+ * cdns3_allocate_trb_pool - Allocates TRB's pool for selected endpoint
+ * @priv_ep: endpoint object
+ *
+ * Function will return 0 on success or -ENOMEM on allocation error
+ */
+static int cdns3_allocate_trb_pool(struct cdns3_endpoint *priv_ep)
+{
+ struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
+ struct cdns3_trb *link_trb;
+
+ if (!priv_ep->trb_pool) {
+ priv_ep->trb_pool = dma_zalloc_coherent(priv_dev->sysdev,
+ TRB_RING_SIZE,
+ &priv_ep->trb_pool_dma,
+ GFP_DMA);
+ if (!priv_ep->trb_pool)
+ return -ENOMEM;
+ } else {
+ memset(priv_ep->trb_pool, 0, TRB_RING_SIZE);
+ }
+
+ if (!priv_ep->aligned_buff) {
+ void *buff = dma_alloc_coherent(priv_dev->sysdev,
+ CDNS3_ALIGNED_BUF_SIZE,
+ &priv_ep->aligned_dma_addr,
+ GFP_DMA);
+
+ priv_ep->aligned_buff = buff;
+ if (!priv_ep->aligned_buff) {
+ dma_free_coherent(priv_dev->sysdev,
+ TRB_RING_SIZE,
+ priv_ep->trb_pool,
+ priv_ep->trb_pool_dma);
+ priv_ep->trb_pool = NULL;
+
+ return -ENOMEM;
+ }
+ }
+
+ /* Initialize the last TRB as Link TRB */
+ link_trb = (priv_ep->trb_pool + TRBS_PER_SEGMENT - 1);
+ link_trb->buffer = TRB_BUFFER(priv_ep->trb_pool_dma);
+ link_trb->control = TRB_CYCLE | TRB_TYPE(TRB_LINK) |
+ TRB_CHAIN | TRB_TOGGLE;
+
+ return 0;
+}
+
+static void cdns3_free_trb_pool(struct cdns3_endpoint *priv_ep)
+{
+ struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
+
+ if (priv_ep->trb_pool) {
+ dma_free_coherent(priv_dev->sysdev,
+ TRB_RING_SIZE,
+ priv_ep->trb_pool, priv_ep->trb_pool_dma);
+ priv_ep->trb_pool = NULL;
+ }
+
+ if (priv_ep->aligned_buff) {
+ dma_free_coherent(priv_dev->sysdev, CDNS3_ALIGNED_BUF_SIZE,
+ priv_ep->aligned_buff,
+ priv_ep->aligned_dma_addr);
+ priv_ep->aligned_buff = NULL;
+ }
+}
+
+/**
+ * cdns3_data_flush - flush data at onchip buffer
+ * @priv_ep: endpoint object
+ *
+ * Endpoint must be selected before call to this function
+ *
+ * Returns zero on success or negative value on failure
+ */
+static int cdns3_data_flush(struct cdns3_endpoint *priv_ep)
+{
+ struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
+
+ writel(EP_CMD_DFLUSH, &priv_dev->regs->ep_cmd);
+
+ /* wait for DFLUSH cleared */
+ return cdns3_handshake(&priv_dev->regs->ep_cmd, EP_CMD_DFLUSH, 0, 100);
+}
+
+/**
+ * cdns3_ep_stall_flush - Stalls and flushes selected endpoint
+ * @priv_ep: endpoint object
+ *
+ * Endpoint must be selected before call to this function
+ */
+static void cdns3_ep_stall_flush(struct cdns3_endpoint *priv_ep)
+{
+ struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
+
+ writel(EP_CMD_DFLUSH | EP_CMD_ERDY | EP_CMD_SSTALL,
+ &priv_dev->regs->ep_cmd);
+
+ /* wait for DFLUSH cleared */
+ cdns3_handshake(&priv_dev->regs->ep_cmd, EP_CMD_DFLUSH, 0, 100);
+ priv_ep->flags |= EP_STALL;
+}
+
+/**
+ * cdns3_gadget_unconfig - reset device configuration
+ * @priv_dev: extended gadget object
+ */
+void cdns3_gadget_unconfig(struct cdns3_device *priv_dev)
+{
+ /* RESET CONFIGURATION */
+ writel(USB_CONF_CFGRST, &priv_dev->regs->usb_conf);
+
+ cdns3_allow_enable_l1(priv_dev, 0);
+ priv_dev->hw_configured_flag = 0;
+ priv_dev->onchip_mem_allocated_size = 0;
+}
+
+/**
+ * cdns3_ep_inc_trb - increment a trb index.
+ * @index: Pointer to the TRB index to increment.
+ * @cs: Cycle state
+ *
+ * The index should never point to the link TRB. After incrementing,
+ * if it is point to the link TRB, wrap around to the beginning and revert
+ * cycle state bit The
+ * link TRB is always at the last TRB entry.
+ */
+static void cdns3_ep_inc_trb(int *index, u8 *cs)
+{
+ (*index)++;
+ if (*index == (TRBS_PER_SEGMENT - 1)) {
+ *index = 0;
+ *cs ^= 1;
+ }
+}
+
+/**
+ * cdns3_ep_inc_enq - increment endpoint's enqueue pointer
+ * @priv_ep: The endpoint whose enqueue pointer we're incrementing
+ */
+static void cdns3_ep_inc_enq(struct cdns3_endpoint *priv_ep)
+{
+ priv_ep->free_trbs--;
+ cdns3_ep_inc_trb(&priv_ep->enqueue, &priv_ep->pcs);
+}
+
+/**
+ * cdns3_ep_inc_deq - increment endpoint's dequeue pointer
+ * @priv_ep: The endpoint whose dequeue pointer we're incrementing
+ */
+static void cdns3_ep_inc_deq(struct cdns3_endpoint *priv_ep)
+{
+ priv_ep->free_trbs++;
+ cdns3_ep_inc_trb(&priv_ep->dequeue, &priv_ep->ccs);
+}
+
+/**
+ * cdns3_allow_enable_l1 - enable/disable permits to transition to L1.
+ * @priv_dev: Extended gadget object
+ * @enable: Enable/disable permit to transition to L1.
+ *
+ * If bit USB_CONF_L1EN is set and device receive Extended Token packet,
+ * then controller answer with ACK handshake.
+ * If bit USB_CONF_L1DS is set and device receive Extended Token packet,
+ * then controller answer with NYET handshake.
+ */
+void cdns3_allow_enable_l1(struct cdns3_device *priv_dev, int enable)
+{
+ if (enable)
+ writel(USB_CONF_L1EN, &priv_dev->regs->usb_conf);
+ else
+ writel(USB_CONF_L1DS, &priv_dev->regs->usb_conf);
+}
+
+enum usb_device_speed cdns3_get_speed(struct cdns3_device *priv_dev)
+{
+ u32 reg;
+
+ reg = readl(&priv_dev->regs->usb_sts);
+
+ if (DEV_SUPERSPEED(reg))
+ return USB_SPEED_SUPER;
+ else if (DEV_HIGHSPEED(reg))
+ return USB_SPEED_HIGH;
+ else if (DEV_FULLSPEED(reg))
+ return USB_SPEED_FULL;
+ else if (DEV_LOWSPEED(reg))
+ return USB_SPEED_LOW;
+ return USB_SPEED_UNKNOWN;
+}
+
+/**
+ * cdns3_start_all_request - add to ring all request not started
+ * @priv_dev: Extended gadget object
+ * @priv_ep: The endpoint for whom request will be started.
+ *
+ * Returns return ENOMEM if transfer ring i not enough TRBs to start
+ * all requests.
+ */
+static int cdns3_start_all_request(struct cdns3_device *priv_dev,
+ struct cdns3_endpoint *priv_ep)
+{
+ struct usb_request *req, *req_temp;
+ int ret = 0;
+
+ list_for_each_entry_safe(req, req_temp, &priv_ep->request_list, list) {
+ struct cdns3_request *priv_req = to_cdns3_request(req);
+
+ if (!(priv_req->flags & REQUEST_PENDING)) {
+ ret = cdns3_ep_run_transfer(priv_ep, req);
+ if (ret)
+ return ret;
+ }
+ }
+
+ priv_ep->flags &= ~EP_RING_FULL;
+ return ret;
+}
+
+/**
+ * cdns3_gadget_giveback - call struct usb_request's ->complete callback
+ * @priv_ep: The endpoint to whom the request belongs to
+ * @priv_req: The request we're giving back
+ * @status: completion code for the request
+ *
+ * Must be called with controller's lock held and interrupts disabled. This
+ * function will unmap @req and call its ->complete() callback to notify upper
+ * layers that it has completed.
+ */
+void cdns3_gadget_giveback(struct cdns3_endpoint *priv_ep,
+ struct cdns3_request *priv_req,
+ int status)
+{
+ struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
+ struct usb_request *request = &priv_req->request;
+
+ list_del_init(&request->list);
+
+ if (request->status == -EINPROGRESS)
+ request->status = status;
+
+ usb_gadget_unmap_request_by_dev(priv_dev->sysdev, request,
+ priv_ep->dir);
+
+ priv_req->flags &= ~REQUEST_PENDING;
+ trace_cdns3_gadget_giveback(priv_req);
+
+ if (priv_req->flags & REQUEST_INTERNAL) {
+ struct usb_request *req;
+
+ req = cdns3_next_request(&priv_ep->request_list);
+
+ priv_ep->descmis_pending = false;
+ priv_ep->descmis_finished = true;
+
+ /*
+ * If no request is queued then driver can't do nothing
+ * with just completed request. Request with flag set to
+ * REQUEST_INTERNAL is only internal used request and driver
+ * can't call complete callback. Before calling completion, data
+ * must be copied to normal usb_request object
+ */
+ if (!req)
+ return;
+
+ req->actual = request->actual;
+ req->status = request->status;
+ memcpy(req->buf, request->buf, request->actual);
+
+ request = req;
+ list_del_init(&request->list);
+ cdns3_start_all_request(priv_dev, priv_ep);
+ priv_ep->descmis_finished = false;
+ }
+
+ /* Start all not pending request */
+ if (priv_ep->flags & EP_RING_FULL)
+ cdns3_start_all_request(priv_dev, priv_ep);
+
+ if (request->complete) {
+ spin_unlock(&priv_dev->lock);
+ usb_gadget_giveback_request(&priv_ep->endpoint,
+ request);
+ spin_lock(&priv_dev->lock);
+ }
+
+ if (request->buf == priv_dev->zlp_buf)
+ cdns3_gadget_ep_free_request(&priv_ep->endpoint, request);
+}
+
+/**
+ * cdns3_ep_run_transfer - start transfer on no-default endpoint hardware
+ * @priv_ep: endpoint object
+ *
+ * Returns zero on success or negative value on failure
+ */
+int cdns3_ep_run_transfer(struct cdns3_endpoint *priv_ep,
+ struct usb_request *request)
+{
+ struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
+ struct cdns3_request *priv_req;
+ struct cdns3_trb *trb;
+ dma_addr_t trb_dma;
+ int sg_iter = 0;
+ u32 first_pcs;
+ int num_trb;
+ int address;
+ int pcs;
+
+ num_trb = request->num_sgs ? request->num_sgs : 1;
+
+ if (num_trb > priv_ep->free_trbs) {
+ priv_ep->flags |= EP_RING_FULL;
+ return -ENOMEM;
+ }
+
+ priv_req = to_cdns3_request(request);
+ address = priv_ep->endpoint.desc->bEndpointAddress;
+
+ if (priv_ep->descmis_pending)
+ return 0;
+
+ if (priv_req->flags & REQUEST_PENDING)
+ goto arm;
+
+ priv_ep->flags |= EP_PENDING_REQUEST;
+ trb_dma = request->dma;
+
+ /* must allocate buffer aligned to 8 */
+ if ((request->dma % 8)) {
+ if (request->length <= CDNS3_ALIGNED_BUF_SIZE) {
+ memcpy(priv_ep->aligned_buff, request->buf,
+ request->length);
+ trb_dma = priv_ep->aligned_dma_addr;
+ } else {
+ return -ENOMEM;
+ }
+ }
+
+ trb = priv_ep->trb_pool + priv_ep->enqueue;
+ priv_req->trb = trb;
+ priv_req->start_trb = priv_ep->enqueue;
+
+ /* prepare ring */
+ if ((priv_ep->enqueue + num_trb) >= (TRBS_PER_SEGMENT - 1)) {
+ /*updating C bt in Link TRB before starting DMA*/
+ struct cdns3_trb *link_trb = priv_ep->trb_pool +
+ (TRBS_PER_SEGMENT - 1);
+ link_trb->control = ((priv_ep->pcs) ? TRB_CYCLE : 0) |
+ TRB_TYPE(TRB_LINK) | TRB_CHAIN |
+ TRB_TOGGLE;
+ }
+
+ first_pcs = priv_ep->pcs ? TRB_CYCLE : 0;
+
+ do {
+ /* fill TRB */
+ trb->buffer = TRB_BUFFER(request->num_sgs == 0
+ ? trb_dma : request->sg[sg_iter].dma_address);
+
+ trb->length = TRB_BURST_LEN(16) |
+ TRB_LEN(request->num_sgs == 0 ?
+ request->length : request->sg[sg_iter].length);
+
+ trb->control = TRB_TYPE(TRB_NORMAL);
+ pcs = priv_ep->pcs ? TRB_CYCLE : 0;
+
+ /*
+ * first trb should be prepared as last to avoid processing
+ * transfer to early
+ */
+ if (sg_iter == request->num_sgs && sg_iter != 0)
+ trb->control |= pcs | TRB_IOC | TRB_ISP;
+ else if (sg_iter != 0)
+ trb->control |= pcs;
+
+ ++sg_iter;
+ ++trb;
+ cdns3_ep_inc_enq(priv_ep);
+ } while (sg_iter < request->num_sgs);
+
+ trb = priv_req->trb;
+ /*
+ * Memory barrier = Cycle Bit must be set before trb->length and
+ * trb->buffer fields.
+ */
+ wmb();
+
+ /* give the TD to the consumer*/
+ if (sg_iter == 1)
+ trb->control |= first_pcs | TRB_IOC | TRB_ISP;
+ else
+ trb->control |= first_pcs;
+
+ priv_req->flags |= REQUEST_PENDING;
+
+ if (priv_req->flags & REQUEST_INTERNAL)
+ priv_ep->descmis_pending = true;
+
+ trace_cdns3_prepare_trb(priv_ep, priv_req->trb);
+ trace_cdns3_ring(priv_ep);
+
+arm:
+ /* arm transfer on selected endpoint */
+ cdns3_select_ep(priv_ep->cdns3_dev, address);
+
+ /*
+ * For DMULT mode we can set address to transfer ring only once after
+ * enabling endpoint.
+ */
+ if (priv_ep->flags & EP_UPDATE_EP_TRBADDR) {
+ writel(EP_TRADDR_TRADDR(priv_ep->trb_pool_dma),
+ &priv_dev->regs->ep_traddr);
+ priv_ep->flags &= ~EP_UPDATE_EP_TRBADDR;
+ }
+
+ if (priv_dev->hw_configured_flag) {
+ /*clearing TRBERR and EP_STS_DESCMIS before seting DRDY*/
+ writel(EP_STS_TRBERR | EP_STS_DESCMIS, &priv_dev->regs->ep_sts);
+ trace_cdns3_doorbell_epx(priv_ep->name);
+ writel(EP_CMD_DRDY, &priv_dev->regs->ep_cmd);
+ }
+
+ return 0;
+}
+
+void cdns3_set_hw_configuration(struct cdns3_device *priv_dev)
+{
+ struct cdns3_endpoint *priv_ep;
+ struct usb_request *request;
+ struct usb_ep *ep;
+ int result = 0;
+
+ if (priv_dev->hw_configured_flag)
+ return;
+
+ writel(USB_CONF_CFGSET, &priv_dev->regs->usb_conf);
+ writel(EP_CMD_ERDY | EP_CMD_REQ_CMPL, &priv_dev->regs->ep_cmd);
+
+ cdns3_set_register_bit(&priv_dev->regs->usb_conf,
+ USB_CONF_U1EN | USB_CONF_U2EN);
+
+ /* wait until configuration set */
+ result = cdns3_handshake(&priv_dev->regs->usb_sts,
+ USB_STS_CFGSTS_MASK, 1, 100);
+
+ priv_dev->hw_configured_flag = 1;
+ cdns3_allow_enable_l1(priv_dev, 1);
+
+ list_for_each_entry(ep, &priv_dev->gadget.ep_list, ep_list) {
+ if (ep->enabled) {
+ priv_ep = ep_to_cdns3_ep(ep);
+ request = cdns3_next_request(&priv_ep->request_list);
+ if (request)
+ cdns3_ep_run_transfer(priv_ep, request);
+ }
+ }
+}
+
+static bool cdns3_request_handled(struct cdns3_endpoint *priv_ep,
+ struct cdns3_request *priv_req)
+{
+ int current_index;
+ struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
+ struct cdns3_trb *trb = priv_req->trb;
+
+ if (!(priv_req->flags & REQUEST_PENDING))
+ return false;
+
+ cdns3_select_ep(priv_dev, priv_ep->endpoint.desc->bEndpointAddress);
+ current_index = (readl(&priv_dev->regs->ep_traddr) -
+ priv_ep->trb_pool_dma) / TRB_SIZE;
+
+ trb = &priv_ep->trb_pool[priv_req->start_trb];
+
+ if ((trb->control & TRB_CYCLE) != priv_ep->ccs)
+ return false;
+
+ /**
+ * case where ep_traddr point to last trb in ring (link trb)
+ * and dequeue pointer already has been changed to first trb
+ */
+ if ((current_index == (TRBS_PER_SEGMENT - 1)) && !priv_ep->dequeue)
+ return false;
+
+ if (priv_req->start_trb != current_index)
+ return true;
+
+ return false;
+}
+
+static void cdns3_transfer_completed(struct cdns3_device *priv_dev,
+ struct cdns3_endpoint *priv_ep)
+{
+ struct usb_request *request;
+ struct cdns3_request *priv_req;
+ struct cdns3_trb *trb;
+
+ while (!list_empty(&priv_ep->request_list)) {
+ request = cdns3_next_request(&priv_ep->request_list);
+ priv_req = to_cdns3_request(request);
+
+ if (!cdns3_request_handled(priv_ep, priv_req))
+ return;
+
+ if (request->dma % 8 && priv_ep->dir == USB_DIR_OUT)
+ memcpy(request->buf, priv_ep->aligned_buff,
+ request->length);
+
+ trb = priv_ep->trb_pool + priv_ep->dequeue;
+ trace_cdns3_complete_trb(priv_ep, trb);
+ if (trb != priv_req->trb)
+ dev_warn(priv_dev->dev,
+ "request_trb=0x%p, queue_trb=0x%p\n",
+ priv_req->trb, trb);
+
+ request->actual = TRB_LEN(le32_to_cpu(trb->length));
+
+ cdns3_ep_inc_deq(priv_ep);
+
+ cdns3_gadget_giveback(priv_ep, priv_req, 0);
+ }
+
+ priv_ep->flags &= ~EP_PENDING_REQUEST;
+}
+
+/**
+ * cdns3_descmissing_packet - handles descriptor missing event.
+ * @priv_dev: extended gadget object
+ *
+ * Function protects gadget functions from getting stuck.
+ * Controller for OUT endpoints has shared on-chip buffers for all incoming
+ * packets, including ep0out. It's FIFO buffer, so packets must be handle by DMA
+ * in correct order. If the first packet in the buffer will not be handled,
+ * then the following packets directed for other endpoints and functions
+ * will be blocked.
+ * Additionally the packets directed to one endpoint can clog entire on-chip
+ * buffers. In this case transfer to other endpoints also will blocked.
+ *
+ * To resolve this issue after raising the descriptor missing interrupt
+ * driver prepares internal usb_request object and use it to arm DMA transfer
+ * for the right endpoint. Driver use only single usb_request with
+ * allocated 64KB buffer, so if host send more not expected transfers, then only
+ * the last will be saved and returned to gadget function.
+ * Such blocking situation was observed on ACM gadget, because host send OUT
+ * data packet but ACM function doesn't want their.
+ */
+static void cdns3_descmissing_packet(struct cdns3_endpoint *priv_ep)
+{
+ struct cdns3_request *priv_req = priv_ep->descmis_req;
+ struct usb_request *request;
+
+ if (!priv_req) {
+ request = cdns3_gadget_ep_alloc_request(&priv_ep->endpoint,
+ GFP_ATOMIC);
+ priv_req = to_cdns3_request(request);
+ priv_req->flags |= REQUEST_INTERNAL;
+ priv_req->request.buf = kzalloc(CDNS3_DESCMIS_BUF_SIZE,
+ GFP_ATOMIC);
+ priv_req->request.length = CDNS3_DESCMIS_BUF_SIZE;
+ priv_ep->descmis_req = priv_req;
+ }
+
+ priv_ep->descmis_finished = false;
+ __cdns3_gadget_ep_queue(&priv_ep->endpoint,
+ &priv_ep->descmis_req->request,
+ GFP_ATOMIC);
+}
+
+/**
+ * cdns3_check_ep_interrupt_proceed - Processes interrupt related to endpoint
+ * @priv_ep: endpoint object
+ *
+ * Returns 0
+ */
+static int cdns3_check_ep_interrupt_proceed(struct cdns3_endpoint *priv_ep)
+{
+ struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
+ u32 ep_sts_reg;
+
+ cdns3_select_ep(priv_dev, priv_ep->endpoint.address);
+ ep_sts_reg = readl(&priv_dev->regs->ep_sts);
+ writel(ep_sts_reg, &priv_dev->regs->ep_sts);
+
+ trace_cdns3_epx_irq(priv_ep);
+
+ if ((ep_sts_reg & EP_STS_IOC) || (ep_sts_reg & EP_STS_ISP))
+ cdns3_transfer_completed(priv_dev, priv_ep);
+
+ if (ep_sts_reg & EP_STS_DESCMIS)
+ cdns3_descmissing_packet(priv_ep);
+
+ return 0;
+}
+
+/**
+ * cdns3_check_usb_interrupt_proceed - Processes interrupt related to device
+ * @priv_dev: extended gadget object
+ * @usb_ists: bitmap representation of device's reported interrupts
+ * (usb_ists register value)
+ */
+static void cdns3_check_usb_interrupt_proceed(struct cdns3_device *priv_dev,
+ u32 usb_ists)
+{
+ int speed = 0;
+
+ trace_cdns3_usb_irq(priv_dev, usb_ists);
+ /* Connection detected */
+ if (usb_ists & (USB_ISTS_CON2I | USB_ISTS_CONI)) {
+ speed = cdns3_get_speed(priv_dev);
+ priv_dev->gadget.speed = speed;
+ usb_gadget_set_state(&priv_dev->gadget, USB_STATE_POWERED);
+ cdns3_ep0_config(priv_dev);
+ }
+
+ /* Disconnection detected */
+ if (usb_ists & (USB_ISTS_DIS2I | USB_ISTS_DISI)) {
+ if (priv_dev->gadget_driver &&
+ priv_dev->gadget_driver->disconnect) {
+ spin_unlock(&priv_dev->lock);
+ priv_dev->gadget_driver->disconnect(&priv_dev->gadget);
+ spin_lock(&priv_dev->lock);
+ }
+
+ priv_dev->gadget.speed = USB_SPEED_UNKNOWN;
+ usb_gadget_set_state(&priv_dev->gadget, USB_STATE_NOTATTACHED);
+ cdns3_gadget_unconfig(priv_dev);
+ }
+
+ /* reset*/
+ if (usb_ists & (USB_ISTS_UWRESI | USB_ISTS_UHRESI | USB_ISTS_U2RESI)) {
+ /*read again to check the actuall speed*/
+ speed = cdns3_get_speed(priv_dev);
+ usb_gadget_set_state(&priv_dev->gadget, USB_STATE_DEFAULT);
+ priv_dev->gadget.speed = speed;
+ cdns3_gadget_unconfig(priv_dev);
+ cdns3_ep0_config(priv_dev);
+ }
+}
+
+/**
+ * cdns3_device_irq_handler- interrupt handler for device part of controller
+ *
+ * @irq: irq number for cdns3 core device
+ * @data: structure of cdns3
+ *
+ * Returns IRQ_HANDLED or IRQ_NONE
+ */
+static irqreturn_t cdns3_device_irq_handler(int irq, void *data)
+{
+ struct cdns3_device *priv_dev;
+ struct cdns3 *cdns = data;
+ irqreturn_t ret = IRQ_NONE;
+ unsigned long flags;
+ u32 reg;
+
+ priv_dev = cdns->gadget_dev;
+ spin_lock_irqsave(&priv_dev->lock, flags);
+
+ /* check USB device interrupt */
+ reg = readl(&priv_dev->regs->usb_ists);
+ writel(reg, &priv_dev->regs->usb_ists);
+
+ if (reg) {
+ dev_dbg(priv_dev->dev, "IRQ: usb_ists: %08X\n", reg);
+ cdns3_check_usb_interrupt_proceed(priv_dev, reg);
+ ret = IRQ_HANDLED;
+ }
+
+ /* check endpoint interrupt */
+ reg = readl(&priv_dev->regs->ep_ists);
+
+ /* handle default endpoint OUT */
+ if (reg & EP_ISTS_EP_OUT0) {
+ cdns3_check_ep0_interrupt_proceed(priv_dev, USB_DIR_OUT);
+ ret = IRQ_HANDLED;
+ }
+
+ /* handle default endpoint IN */
+ if (reg & EP_ISTS_EP_IN0) {
+ cdns3_check_ep0_interrupt_proceed(priv_dev, USB_DIR_IN);
+ ret = IRQ_HANDLED;
+ }
+
+ /* check if interrupt from non default endpoint, if no exit */
+ reg &= ~(EP_ISTS_EP_OUT0 | EP_ISTS_EP_IN0);
+ if (!reg)
+ goto irqend;
+
+ do {
+ unsigned int bit_pos = ffs(reg);
+ u32 bit_mask = 1 << (bit_pos - 1);
+ int index;
+
+ index = cdns3_ep_reg_pos_to_index(bit_pos);
+ cdns3_check_ep_interrupt_proceed(priv_dev->eps[index]);
+ reg &= ~bit_mask;
+ ret = IRQ_HANDLED;
+ } while (reg);
+
+irqend:
+ spin_unlock_irqrestore(&priv_dev->lock, flags);
+ return ret;
+}
+
+/**
+ * cdns3_ep_onchip_buffer_reserve - Try to reserve onchip buf for EP
+ *
+ * The real reservation will occur during write to EP_CFG register,
+ * this function is used to check if the 'size' reservation is allowed.
+ *
+ * @priv_dev: extended gadget object
+ * @size: the size (KB) for EP would like to allocate
+ *
+ * Return 0 if the required size can met or negative value on failure
+ */
+static int cdns3_ep_onchip_buffer_reserve(struct cdns3_device *priv_dev,
+ int size)
+{
+ u32 onchip_mem;
+
+ priv_dev->onchip_mem_allocated_size += size;
+
+ onchip_mem = USB_CAP2_ACTUAL_MEM_SIZE(readl(&priv_dev->regs->usb_cap2));
+ if (!onchip_mem)
+ onchip_mem = 256;
+
+ /* 2KB is reserved for EP0*/
+ onchip_mem -= 2;
+ if (priv_dev->onchip_mem_allocated_size > onchip_mem) {
+ priv_dev->onchip_mem_allocated_size -= size;
+ return -EPERM;
+ }
+
+ return 0;
+}
+
+/**
+ * cdns3_ep_config Configure hardware endpoint
+ * @priv_ep: extended endpoint object
+ */
+void cdns3_ep_config(struct cdns3_endpoint *priv_ep)
+{
+ bool is_iso_ep = (priv_ep->type == USB_ENDPOINT_XFER_ISOC);
+ struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
+ u32 bEndpointAddress = priv_ep->num | priv_ep->dir;
+ u32 interrupt_mask = EP_STS_EN_TRBERREN;
+ u32 max_packet_size = 0;
+ u32 ep_cfg = 0;
+ int ret;
+
+ if (!priv_ep->dir)
+ interrupt_mask |= EP_STS_EN_DESCMISEN;
+
+ if (priv_ep->type == USB_ENDPOINT_XFER_INT) {
+ ep_cfg = EP_CFG_EPTYPE(USB_ENDPOINT_XFER_INT);
+ } else if (priv_ep->type == USB_ENDPOINT_XFER_BULK) {
+ ep_cfg = EP_CFG_EPTYPE(USB_ENDPOINT_XFER_BULK);
+ } else {
+ ep_cfg = EP_CFG_EPTYPE(USB_ENDPOINT_XFER_ISOC);
+ interrupt_mask = 0xFFFFFFFF;
+ }
+
+ switch (priv_dev->gadget.speed) {
+ case USB_SPEED_FULL:
+ max_packet_size = is_iso_ep ? 1023 : 64;
+ break;
+ case USB_SPEED_HIGH:
+ max_packet_size = is_iso_ep ? 1024 : 512;
+ break;
+ case USB_SPEED_SUPER:
+ max_packet_size = 1024;
+ break;
+ default:
+ /* all other speed are not supported */
+ return;
+ }
+
+ ret = cdns3_ep_onchip_buffer_reserve(priv_dev, CDNS3_EP_BUF_SIZE);
+ if (ret) {
+ dev_err(priv_dev->dev, "onchip mem is full, ep is invalid\n");
+ return;
+ }
+
+ ep_cfg |= EP_CFG_MAXPKTSIZE(max_packet_size) |
+ EP_CFG_BUFFERING(CDNS3_EP_BUF_SIZE - 1) |
+ EP_CFG_MAXBURST(priv_ep->endpoint.maxburst);
+
+ cdns3_select_ep(priv_dev, bEndpointAddress);
+
+ writel(ep_cfg, &priv_dev->regs->ep_cfg);
+ writel(interrupt_mask, &priv_dev->regs->ep_sts_en);
+
+ dev_dbg(priv_dev->dev, "Configure %s: with val %08x\n",
+ priv_ep->name, ep_cfg);
+
+ /* enable interrupt for selected endpoint */
+ cdns3_set_register_bit(&priv_dev->regs->ep_ien,
+ cdns3_ep_addr_to_bit_pos(bEndpointAddress));
+}
+
+/* Find correct direction for HW endpoint according to description */
+static int cdns3_ep_dir_is_correct(struct usb_endpoint_descriptor *desc,
+ struct cdns3_endpoint *priv_ep)
+{
+ return (priv_ep->endpoint.caps.dir_in && usb_endpoint_dir_in(desc)) ||
+ (priv_ep->endpoint.caps.dir_out && usb_endpoint_dir_out(desc));
+}
+
+static struct
+cdns3_endpoint *cdns3_find_available_ep(struct cdns3_device *priv_dev,
+ struct usb_endpoint_descriptor *desc)
+{
+ struct usb_ep *ep;
+ struct cdns3_endpoint *priv_ep;
+
+ list_for_each_entry(ep, &priv_dev->gadget.ep_list, ep_list) {
+ unsigned long num;
+ int ret;
+ /* ep name pattern likes epXin or epXout */
+ char c[2] = {ep->name[2], '\0'};
+
+ ret = kstrtoul(c, 10, &num);
+ if (ret)
+ return ERR_PTR(ret);
+
+ priv_ep = ep_to_cdns3_ep(ep);
+ if (cdns3_ep_dir_is_correct(desc, priv_ep)) {
+ if (!(priv_ep->flags & EP_CLAIMED)) {
+ priv_ep->num = num;
+ return priv_ep;
+ }
+ }
+ }
+ return ERR_PTR(-ENOENT);
+}
+
+static struct
+usb_ep *cdns3_gadget_match_ep(struct usb_gadget *gadget,
+ struct usb_endpoint_descriptor *desc,
+ struct usb_ss_ep_comp_descriptor *comp_desc)
+{
+ struct cdns3_device *priv_dev = gadget_to_cdns3_device(gadget);
+ struct cdns3_endpoint *priv_ep;
+ unsigned long flags;
+
+ priv_ep = cdns3_find_available_ep(priv_dev, desc);
+ if (IS_ERR(priv_ep)) {
+ dev_err(priv_dev->dev, "no available ep\n");
+ return NULL;
+ }
+
+ dev_dbg(priv_dev->dev, "match endpoint: %s\n", priv_ep->name);
+
+ spin_lock_irqsave(&priv_dev->lock, flags);
+ priv_ep->endpoint.desc = desc;
+ priv_ep->dir = usb_endpoint_dir_in(desc) ? USB_DIR_IN : USB_DIR_OUT;
+ priv_ep->type = usb_endpoint_type(desc);
+ priv_ep->flags |= EP_CLAIMED;
+ spin_unlock_irqrestore(&priv_dev->lock, flags);
+ return &priv_ep->endpoint;
+}
+
+/**
+ * cdns3_gadget_ep_alloc_request Allocates request
+ * @ep: endpoint object associated with request
+ * @gfp_flags: gfp flags
+ *
+ * Returns allocated request address, NULL on allocation error
+ */
+struct usb_request *cdns3_gadget_ep_alloc_request(struct usb_ep *ep,
+ gfp_t gfp_flags)
+{
+ struct cdns3_endpoint *priv_ep = ep_to_cdns3_ep(ep);
+ struct cdns3_request *priv_req;
+
+ priv_req = kzalloc(sizeof(*priv_req), gfp_flags);
+ if (!priv_req)
+ return NULL;
+
+ priv_req->priv_ep = priv_ep;
+
+ trace_cdns3_alloc_request(priv_req);
+ return &priv_req->request;
+}
+
+/**
+ * cdns3_gadget_ep_free_request Free memory occupied by request
+ * @ep: endpoint object associated with request
+ * @request: request to free memory
+ */
+void cdns3_gadget_ep_free_request(struct usb_ep *ep,
+ struct usb_request *request)
+{
+ struct cdns3_request *priv_req = to_cdns3_request(request);
+
+ trace_cdns3_free_request(priv_req);
+ kfree(priv_req);
+}
+
+/**
+ * cdns3_gadget_ep_enable Enable endpoint
+ * @ep: endpoint object
+ * @desc: endpoint descriptor
+ *
+ * Returns 0 on success, error code elsewhere
+ */
+static int cdns3_gadget_ep_enable(struct usb_ep *ep,
+ const struct usb_endpoint_descriptor *desc)
+{
+ struct cdns3_endpoint *priv_ep;
+ struct cdns3_device *priv_dev;
+ unsigned long flags;
+ int ret;
+ u32 reg;
+
+ priv_ep = ep_to_cdns3_ep(ep);
+ priv_dev = priv_ep->cdns3_dev;
+
+ if (!ep || !desc || desc->bDescriptorType != USB_DT_ENDPOINT) {
+ dev_dbg(priv_dev->dev, "usbss: invalid parameters\n");
+ return -EINVAL;
+ }
+
+ if (!desc->wMaxPacketSize) {
+ dev_err(priv_dev->dev, "usbss: missing wMaxPacketSize\n");
+ return -EINVAL;
+ }
+
+ if (dev_WARN_ONCE(priv_dev->dev, priv_ep->flags & EP_ENABLED,
+ "%s is already enabled\n", priv_ep->name))
+ return 0;
+
+ ret = cdns3_allocate_trb_pool(priv_ep);
+ if (ret)
+ return ret;
+
+ trace_cdns3_gadget_ep_enable(priv_ep);
+ spin_lock_irqsave(&priv_dev->lock, flags);
+
+ priv_ep->endpoint.desc = desc;
+ priv_ep->dir = usb_endpoint_dir_in(desc) ? USB_DIR_IN : USB_DIR_OUT;
+ priv_ep->type = usb_endpoint_type(desc);
+
+ cdns3_select_ep(priv_dev, desc->bEndpointAddress);
+ writel(EP_CMD_EPRST, &priv_dev->regs->ep_cmd);
+
+ ret = cdns3_handshake(&priv_dev->regs->ep_cmd,
+ EP_CMD_CSTALL | EP_CMD_EPRST, 0, 100);
+
+ cdns3_set_register_bit(&priv_dev->regs->ep_cfg, EP_CFG_ENABLE);
+
+ ep->desc = desc;
+ priv_ep->flags &= ~(EP_PENDING_REQUEST | EP_STALL);
+ priv_ep->flags |= EP_ENABLED | EP_UPDATE_EP_TRBADDR;
+ priv_ep->enqueue = 0;
+ priv_ep->dequeue = 0;
+ reg = readl(&priv_dev->regs->ep_sts);
+ priv_ep->pcs = !!EP_STS_CCS(reg);
+ priv_ep->ccs = !!EP_STS_CCS(reg);
+ /* one TRB is reserved for link TRB used in DMULT mode*/
+ priv_ep->free_trbs = TRBS_PER_SEGMENT - 1;
+
+ spin_unlock_irqrestore(&priv_dev->lock, flags);
+ return 0;
+}
+
+/**
+ * cdns3_gadget_ep_disable Disable endpoint
+ * @ep: endpoint object
+ *
+ * Returns 0 on success, error code elsewhere
+ */
+static int cdns3_gadget_ep_disable(struct usb_ep *ep)
+{
+ struct cdns3_endpoint *priv_ep;
+ struct cdns3_device *priv_dev;
+ unsigned long flags;
+ int ret = 0;
+ struct usb_request *request;
+ u32 ep_cfg;
+
+ if (!ep) {
+ dev_dbg(priv_dev->dev, "usbss: invalid parameters\n");
+ return -EINVAL;
+ }
+
+ priv_ep = ep_to_cdns3_ep(ep);
+ priv_dev = priv_ep->cdns3_dev;
+
+ if (dev_WARN_ONCE(priv_dev->dev, !(priv_ep->flags & EP_ENABLED),
+ "%s is already disabled\n", priv_ep->name))
+ return 0;
+
+ spin_lock_irqsave(&priv_dev->lock, flags);
+
+ trace_cdns3_gadget_ep_disable(priv_ep);
+
+ cdns3_select_ep(priv_dev, ep->desc->bEndpointAddress);
+ ret = cdns3_data_flush(priv_ep);
+
+ ep_cfg = readl(&priv_dev->regs->ep_cfg);
+ ep_cfg &= ~EP_CFG_ENABLE;
+ writel(ep_cfg, &priv_dev->regs->ep_cfg);
+
+ while (!list_empty(&priv_ep->request_list)) {
+ request = cdns3_next_request(&priv_ep->request_list);
+
+ cdns3_gadget_giveback(priv_ep, to_cdns3_request(request),
+ -ESHUTDOWN);
+ }
+
+ if (priv_ep->descmis_req) {
+ kfree(priv_ep->descmis_req->request.buf);
+ cdns3_gadget_ep_free_request(&priv_ep->endpoint,
+ &priv_ep->descmis_req->request);
+ priv_ep->descmis_req = NULL;
+ priv_ep->descmis_pending = false;
+ priv_ep->descmis_finished = false;
+ }
+
+ ep->desc = NULL;
+ priv_ep->flags &= ~EP_ENABLED;
+
+ spin_unlock_irqrestore(&priv_dev->lock, flags);
+
+ return ret;
+}
+
+/**
+ * cdns3_gadget_ep_queue Transfer data on endpoint
+ * @ep: endpoint object
+ * @request: request object
+ * @gfp_flags: gfp flags
+ *
+ * Returns 0 on success, error code elsewhere
+ */
+static int __cdns3_gadget_ep_queue(struct usb_ep *ep,
+ struct usb_request *request,
+ gfp_t gfp_flags)
+{
+ struct cdns3_endpoint *priv_ep = ep_to_cdns3_ep(ep);
+ struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
+ struct cdns3_request *priv_req;
+ int ret = 0;
+
+ request->actual = 0;
+ request->status = -EINPROGRESS;
+ priv_req = to_cdns3_request(request);
+
+ trace_cdns3_ep_queue(priv_req);
+
+ /* Data will be copied from internal usb_request object. */
+ if (priv_ep->descmis_finished) {
+ priv_ep->descmis_finished = false;
+ request->actual = priv_ep->descmis_req->request.actual;
+
+ memcpy(request->buf, priv_ep->descmis_req->request.buf,
+ priv_ep->descmis_req->request.actual);
+ list_add_tail(&request->list, &priv_ep->request_list);
+
+ cdns3_gadget_giveback(priv_ep,
+ priv_req,
+ priv_ep->descmis_req->request.status);
+
+ return ret;
+ }
+
+ ret = usb_gadget_map_request_by_dev(priv_dev->sysdev, request,
+ usb_endpoint_dir_in(ep->desc));
+ if (ret)
+ return ret;
+
+ list_add_tail(&request->list, &priv_ep->request_list);
+
+ cdns3_ep_run_transfer(priv_ep, request);
+
+ return ret;
+}
+
+static int cdns3_gadget_ep_queue(struct usb_ep *ep, struct usb_request *request,
+ gfp_t gfp_flags)
+{
+ struct cdns3_endpoint *priv_ep = ep_to_cdns3_ep(ep);
+ struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
+ struct usb_request *zlp_request;
+ unsigned long flags;
+ int ret;
+
+ if (!request || !ep)
+ return -EINVAL;
+
+ spin_lock_irqsave(&priv_dev->lock, flags);
+ ret = __cdns3_gadget_ep_queue(ep, request, gfp_flags);
+
+ if (ret == 0 && request->zero && request->length &&
+ (request->length % ep->maxpacket == 0)) {
+ struct cdns3_request *priv_req;
+
+ zlp_request = cdns3_gadget_ep_alloc_request(ep, GFP_ATOMIC);
+ zlp_request->buf = priv_dev->zlp_buf;
+ zlp_request->length = 0;
+
+ priv_req = to_cdns3_request(zlp_request);
+ priv_req->flags |= REQUEST_ZLP;
+
+ dev_dbg(priv_dev->dev, "Queuing ZLP for endpoint: %s\n",
+ priv_ep->name);
+ ret = __cdns3_gadget_ep_queue(ep, zlp_request, gfp_flags);
+ }
+
+ spin_unlock_irqrestore(&priv_dev->lock, flags);
+ return ret;
+}
+
+/**
+ * cdns3_gadget_ep_dequeue Remove request from transfer queue
+ * @ep: endpoint object associated with request
+ * @request: request object
+ *
+ * Returns 0 on success, error code elsewhere
+ */
+int cdns3_gadget_ep_dequeue(struct usb_ep *ep,
+ struct usb_request *request)
+{
+ struct cdns3_endpoint *priv_ep = ep_to_cdns3_ep(ep);
+ struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
+ struct usb_request *req, *req_temp;
+ struct cdns3_request *priv_req;
+ unsigned long flags;
+ int ret = 0;
+
+ if (!ep || !request || !ep->desc)
+ return -EINVAL;
+
+ spin_lock_irqsave(&priv_dev->lock, flags);
+
+ priv_req = to_cdns3_request(request);
+
+ trace_cdns3_ep_dequeue(priv_req);
+
+ cdns3_select_ep(priv_dev, ep->desc->bEndpointAddress);
+
+ list_for_each_entry_safe(req, req_temp, &priv_ep->request_list, list) {
+ if (request == req) {
+ cdns3_gadget_giveback(priv_ep,
+ priv_req,
+ -ECONNRESET);
+ break;
+ }
+ }
+
+ spin_unlock_irqrestore(&priv_dev->lock, flags);
+ return ret;
+}
+
+/**
+ * cdns3_gadget_ep_set_halt Sets/clears stall on selected endpoint
+ * @ep: endpoint object to set/clear stall on
+ * @value: 1 for set stall, 0 for clear stall
+ *
+ * Returns 0 on success, error code elsewhere
+ */
+int cdns3_gadget_ep_set_halt(struct usb_ep *ep, int value)
+{
+ struct cdns3_endpoint *priv_ep = ep_to_cdns3_ep(ep);
+ struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
+ unsigned long flags;
+ int ret = 0;
+
+ if (!(priv_ep->flags & EP_ENABLED))
+ return -EPERM;
+
+ spin_lock_irqsave(&priv_dev->lock, flags);
+
+ /* if actual transfer is pending defer setting stall on this endpoint */
+ if ((priv_ep->flags & EP_PENDING_REQUEST) && value) {
+ priv_ep->flags |= EP_STALL;
+ goto finish;
+ }
+
+ dev_dbg(priv_dev->dev, "Halt endpoint %s\n", priv_ep->name);
+
+ cdns3_select_ep(priv_dev, ep->desc->bEndpointAddress);
+ if (value) {
+ cdns3_ep_stall_flush(priv_ep);
+ } else {
+ priv_ep->flags &= ~EP_WEDGE;
+ writel(EP_CMD_CSTALL | EP_CMD_EPRST, &priv_dev->regs->ep_cmd);
+
+ /* wait for EPRST cleared */
+ ret = cdns3_handshake(&priv_dev->regs->ep_cmd,
+ EP_CMD_EPRST, 0, 100);
+ if (unlikely(ret)) {
+ dev_err(priv_dev->dev,
+ "Clearing halt condition failed for %s\n",
+ priv_ep->name);
+ goto finish;
+
+ } else {
+ priv_ep->flags &= ~EP_STALL;
+ }
+ }
+
+ priv_ep->flags &= ~EP_PENDING_REQUEST;
+finish:
+ spin_unlock_irqrestore(&priv_dev->lock, flags);
+
+ return ret;
+}
+
+extern const struct usb_ep_ops cdns3_gadget_ep0_ops;
+
+static const struct usb_ep_ops cdns3_gadget_ep_ops = {
+ .enable = cdns3_gadget_ep_enable,
+ .disable = cdns3_gadget_ep_disable,
+ .alloc_request = cdns3_gadget_ep_alloc_request,
+ .free_request = cdns3_gadget_ep_free_request,
+ .queue = cdns3_gadget_ep_queue,
+ .dequeue = cdns3_gadget_ep_dequeue,
+ .set_halt = cdns3_gadget_ep_set_halt,
+ .set_wedge = cdns3_gadget_ep_set_wedge,
+};
+
+/**
+ * cdns3_gadget_get_frame Returns number of actual ITP frame
+ * @gadget: gadget object
+ *
+ * Returns number of actual ITP frame
+ */
+static int cdns3_gadget_get_frame(struct usb_gadget *gadget)
+{
+ struct cdns3_device *priv_dev = gadget_to_cdns3_device(gadget);
+
+ return readl(&priv_dev->regs->usb_iptn);
+}
+
+static int cdns3_gadget_wakeup(struct usb_gadget *gadget)
+{
+ return 0;
+}
+
+static int cdns3_gadget_set_selfpowered(struct usb_gadget *gadget,
+ int is_selfpowered)
+{
+ struct cdns3_device *priv_dev = gadget_to_cdns3_device(gadget);
+ unsigned long flags;
+
+ spin_lock_irqsave(&priv_dev->lock, flags);
+ priv_dev->is_selfpowered = !!is_selfpowered;
+ spin_unlock_irqrestore(&priv_dev->lock, flags);
+ return 0;
+}
+
+static int cdns3_gadget_pullup(struct usb_gadget *gadget, int is_on)
+{
+ struct cdns3_device *priv_dev = gadget_to_cdns3_device(gadget);
+
+ if (is_on)
+ writel(USB_CONF_DEVEN, &priv_dev->regs->usb_conf);
+ else
+ writel(USB_CONF_DEVDS, &priv_dev->regs->usb_conf);
+
+ return 0;
+}
+
+static void cdns3_gadget_config(struct cdns3_device *priv_dev)
+{
+ struct cdns3_usb_regs __iomem *regs = priv_dev->regs;
+
+ cdns3_ep0_config(priv_dev);
+
+ /* enable interrupts for endpoint 0 (in and out) */
+ writel(EP_IEN_EP_OUT0 | EP_IEN_EP_IN0, &regs->ep_ien);
+
+ /* enable generic interrupt*/
+ writel(USB_IEN_INIT, &regs->usb_ien);
+ writel(USB_CONF_CLK2OFFDS | USB_CONF_L1DS, &regs->usb_conf);
+ writel(USB_CONF_DMULT, &regs->usb_conf);
+ writel(USB_CONF_DEVEN, &regs->usb_conf);
+}
+
+/**
+ * cdns3_gadget_udc_start Gadget start
+ * @gadget: gadget object
+ * @driver: driver which operates on this gadget
+ *
+ * Returns 0 on success, error code elsewhere
+ */
+static int cdns3_gadget_udc_start(struct usb_gadget *gadget,
+ struct usb_gadget_driver *driver)
+{
+ struct cdns3_device *priv_dev = gadget_to_cdns3_device(gadget);
+ unsigned long flags;
+
+ spin_lock_irqsave(&priv_dev->lock, flags);
+ priv_dev->gadget_driver = driver;
+ cdns3_gadget_config(priv_dev);
+ spin_unlock_irqrestore(&priv_dev->lock, flags);
+ return 0;
+}
+
+/**
+ * cdns3_gadget_udc_stop Stops gadget
+ * @gadget: gadget object
+ *
+ * Returns 0
+ */
+static int cdns3_gadget_udc_stop(struct usb_gadget *gadget)
+{
+ struct cdns3_device *priv_dev = gadget_to_cdns3_device(gadget);
+ struct cdns3_endpoint *priv_ep;
+ u32 bEndpointAddress;
+ struct usb_ep *ep;
+ int ret = 0;
+ int i;
+
+ priv_dev->gadget_driver = NULL;
+
+ priv_dev->onchip_mem_allocated_size = 0;
+ priv_dev->gadget.speed = USB_SPEED_UNKNOWN;
+
+ for (i = 0; i < priv_dev->ep_nums ; i++)
+ cdns3_free_trb_pool(priv_dev->eps[i]);
+
+ list_for_each_entry(ep, &priv_dev->gadget.ep_list, ep_list) {
+ priv_ep = ep_to_cdns3_ep(ep);
+ bEndpointAddress = priv_ep->num | priv_ep->dir;
+ cdns3_select_ep(priv_dev, bEndpointAddress);
+ writel(EP_CMD_EPRST, &priv_dev->regs->ep_cmd);
+ ret = cdns3_handshake(&priv_dev->regs->ep_cmd,
+ EP_CMD_EPRST, 0, 100);
+ }
+
+ /* disable interrupt for device */
+ writel(0, &priv_dev->regs->usb_ien);
+ writel(USB_CONF_DEVDS, &priv_dev->regs->usb_conf);
+
+ return ret;
+}
+
+static const struct usb_gadget_ops cdns3_gadget_ops = {
+ .get_frame = cdns3_gadget_get_frame,
+ .wakeup = cdns3_gadget_wakeup,
+ .set_selfpowered = cdns3_gadget_set_selfpowered,
+ .pullup = cdns3_gadget_pullup,
+ .udc_start = cdns3_gadget_udc_start,
+ .udc_stop = cdns3_gadget_udc_stop,
+ .match_ep = cdns3_gadget_match_ep,
+};
+
+static void cdns3_free_all_ep(struct cdns3_device *priv_dev)
+{
+ int i;
+
+ for (i = 0; i < CDNS3_ENDPOINTS_MAX_COUNT; i++)
+ if (priv_dev->eps[i])
+ devm_kfree(priv_dev->dev, priv_dev->eps[i]);
+
+ if (priv_dev->gadget.ep0)
+ devm_kfree(priv_dev->dev, priv_dev->gadget.ep0);
+}
+
+/**
+ * cdns3_init_ep Initializes software endpoints of gadget
+ * @cdns3: extended gadget object
+ *
+ * Returns 0 on success, error code elsewhere
+ */
+static int cdns3_init_ep(struct cdns3_device *priv_dev)
+{
+ u32 ep_enabled_reg, iso_ep_reg;
+ struct cdns3_endpoint *priv_ep;
+ int found_endpoints = 0;
+ int ep_dir, ep_number;
+ u32 ep_mask;
+ int i;
+
+ /* Read it from USB_CAP3 to USB_CAP5 */
+ ep_enabled_reg = readl(&priv_dev->regs->usb_cap3);
+ iso_ep_reg = readl(&priv_dev->regs->usb_cap4);
+
+ dev_dbg(priv_dev->dev, "Initializing non-zero endpoints\n");
+
+ for (i = 0; i < CDNS3_ENDPOINTS_MAX_COUNT; i++) {
+ ep_number = (i / 2) + 1;
+ ep_dir = i % 2;
+ ep_mask = BIT((16 * ep_dir) + ep_number);
+
+ if (!(ep_enabled_reg & ep_mask))
+ continue;
+
+ priv_ep = devm_kzalloc(priv_dev->dev, sizeof(*priv_ep),
+ GFP_KERNEL);
+ if (!priv_ep)
+ return -ENOMEM;
+
+ /* set parent of endpoint object */
+ priv_ep->cdns3_dev = priv_dev;
+ priv_dev->eps[found_endpoints++] = priv_ep;
+
+ snprintf(priv_ep->name, sizeof(priv_ep->name), "ep%d%s",
+ ep_number, !!ep_dir ? "in" : "out");
+ priv_ep->endpoint.name = priv_ep->name;
+
+ usb_ep_set_maxpacket_limit(&priv_ep->endpoint,
+ CDNS3_EP_MAX_PACKET_LIMIT);
+ priv_ep->endpoint.max_streams = CDNS3_EP_MAX_STREAMS;
+ priv_ep->endpoint.ops = &cdns3_gadget_ep_ops;
+ if (ep_dir)
+ priv_ep->endpoint.caps.dir_in = 1;
+ else
+ priv_ep->endpoint.caps.dir_out = 1;
+
+ if (iso_ep_reg & ep_mask)
+ priv_ep->endpoint.caps.type_iso = 1;
+
+ priv_ep->endpoint.caps.type_bulk = 1;
+ priv_ep->endpoint.caps.type_int = 1;
+ priv_ep->endpoint.maxburst = CDNS3_EP_BUF_SIZE - 1;
+
+ priv_ep->flags = 0;
+
+ dev_info(priv_dev->dev, "Initialized %s support: %s %s\n",
+ priv_ep->name,
+ priv_ep->endpoint.caps.type_bulk ? "BULK, INT" : "",
+ priv_ep->endpoint.caps.type_iso ? "ISO" : "");
+
+ list_add_tail(&priv_ep->endpoint.ep_list,
+ &priv_dev->gadget.ep_list);
+ INIT_LIST_HEAD(&priv_ep->request_list);
+ }
+
+ priv_dev->ep_nums = found_endpoints;
+ return 0;
+}
+
+static void cdns3_gadget_disable(struct cdns3 *cdns)
+{
+ struct cdns3_device *priv_dev;
+
+ priv_dev = cdns->gadget_dev;
+
+ if (priv_dev->gadget_driver)
+ priv_dev->gadget_driver->disconnect(&priv_dev->gadget);
+
+ usb_gadget_disconnect(&priv_dev->gadget);
+ priv_dev->gadget.speed = USB_SPEED_UNKNOWN;
+}
+
+void cdns3_gadget_exit(struct cdns3 *cdns)
+{
+ struct cdns3_device *priv_dev;
+
+ priv_dev = cdns->gadget_dev;
+
+ cdns3_gadget_disable(cdns);
+
+ devm_free_irq(cdns->dev, cdns->irq, cdns);
+
+ pm_runtime_mark_last_busy(cdns->dev);
+ pm_runtime_put_autosuspend(cdns->dev);
+
+ usb_del_gadget_udc(&priv_dev->gadget);
+
+ cdns3_free_all_ep(priv_dev);
+
+ dma_free_coherent(priv_dev->sysdev, 8, priv_dev->setup_buf,
+ priv_dev->setup_dma);
+ dma_free_coherent(priv_dev->sysdev, TRB_SIZE * 2, priv_dev->ep0_trb,
+ priv_dev->ep0_trb_dma);
+
+ kfree(priv_dev->zlp_buf);
+ kfree(priv_dev);
+ cdns->gadget_dev = NULL;
+}
+
+static int cdns3_gadget_start(struct cdns3 *cdns)
+{
+ struct cdns3_device *priv_dev;
+ u32 max_speed;
+ int ret;
+
+ priv_dev = kzalloc(sizeof(*priv_dev), GFP_KERNEL);
+ if (!priv_dev)
+ return -ENOMEM;
+
+ cdns->gadget_dev = priv_dev;
+ priv_dev->sysdev = cdns->dev;
+ priv_dev->dev = cdns->dev;
+ priv_dev->regs = cdns->dev_regs;
+
+ max_speed = usb_get_maximum_speed(cdns->dev);
+
+ /* Check the maximum_speed parameter */
+ switch (max_speed) {
+ case USB_SPEED_FULL:
+ case USB_SPEED_HIGH:
+ case USB_SPEED_SUPER:
+ break;
+ default:
+ dev_err(cdns->dev, "invalid maximum_speed parameter %d\n",
+ max_speed);
+ /* fall through */
+ case USB_SPEED_UNKNOWN:
+ /* default to superspeed */
+ max_speed = USB_SPEED_SUPER;
+ break;
+ }
+
+ /* fill gadget fields */
+ priv_dev->gadget.max_speed = max_speed;
+ priv_dev->gadget.speed = USB_SPEED_UNKNOWN;
+ priv_dev->gadget.ops = &cdns3_gadget_ops;
+ priv_dev->gadget.name = "usb-ss-gadget";
+ priv_dev->gadget.sg_supported = 1;
+
+ spin_lock_init(&priv_dev->lock);
+ INIT_WORK(&priv_dev->pending_status_wq,
+ cdns3_pending_setup_status_handler);
+
+ /* initialize endpoint container */
+ INIT_LIST_HEAD(&priv_dev->gadget.ep_list);
+
+ ret = cdns3_init_ep0(priv_dev);
+ if (ret) {
+ dev_err(priv_dev->dev, "Failed to create endpoint 0\n");
+ goto err1;
+ }
+
+ ret = cdns3_init_ep(priv_dev);
+ if (ret) {
+ dev_err(priv_dev->dev, "Failed to create non zero endpoints\n");
+ goto err1;
+ }
+
+ /* allocate memory for default endpoint TRB */
+ priv_dev->ep0_trb = dma_alloc_coherent(priv_dev->sysdev, TRB_SIZE * 2,
+ &priv_dev->ep0_trb_dma, GFP_DMA);
+ if (!priv_dev->ep0_trb) {
+ dev_err(priv_dev->dev, "Failed to allocate memory for ep0 TRB\n");
+ ret = -ENOMEM;
+ goto err1;
+ }
+
+ /* allocate memory for setup packet buffer */
+ priv_dev->setup_buf = dma_alloc_coherent(priv_dev->sysdev, 8,
+ &priv_dev->setup_dma, GFP_DMA);
+ if (!priv_dev->setup_buf) {
+ dev_err(priv_dev->dev, "Failed to allocate memory for SETUP buffer\n");
+ ret = -ENOMEM;
+ goto err2;
+ }
+
+ dev_dbg(priv_dev->dev, "Device Controller version: %08x\n",
+ readl(&priv_dev->regs->usb_cap6));
+ dev_dbg(priv_dev->dev, "USB Capabilities:: %08x\n",
+ readl(&priv_dev->regs->usb_cap1));
+ dev_dbg(priv_dev->dev, "On-Chip memory cnfiguration: %08x\n",
+ readl(&priv_dev->regs->usb_cap2));
+
+ priv_dev->zlp_buf = kzalloc(CDNS3_EP_ZLP_BUF_SIZE, GFP_KERNEL);
+ if (!priv_dev->zlp_buf) {
+ ret = -ENOMEM;
+ goto err3;
+ }
+
+ /* add USB gadget device */
+ ret = usb_add_gadget_udc(priv_dev->dev, &priv_dev->gadget);
+ if (ret < 0) {
+ dev_err(priv_dev->dev,
+ "Failed to register USB device controller\n");
+ goto err4;
+ }
+
+ return 0;
+err4:
+ kfree(priv_dev->zlp_buf);
+err3:
+ dma_free_coherent(priv_dev->sysdev, 8, priv_dev->setup_buf,
+ priv_dev->setup_dma);
+err2:
+ dma_free_coherent(priv_dev->sysdev, TRB_SIZE * 2, priv_dev->ep0_trb,
+ priv_dev->ep0_trb_dma);
+err1:
+ cdns->gadget_dev = NULL;
+ return ret;
+}
+
+static int __cdns3_gadget_init(struct cdns3 *cdns)
+{
+ struct cdns3_device *priv_dev;
+ unsigned long flags;
+ int ret = 0;
+
+ ret = cdns3_gadget_start(cdns);
+ if (ret)
+ return ret;
+
+ priv_dev = cdns->gadget_dev;
+ ret = devm_request_irq(cdns->dev, cdns->irq, cdns3_device_irq_handler,
+ IRQF_SHARED, dev_name(cdns->dev), cdns);
+
+ if (ret)
+ goto err0;
+
+ pm_runtime_get_sync(cdns->dev);
+ spin_lock_irqsave(&priv_dev->lock, flags);
+ spin_unlock_irqrestore(&priv_dev->lock, flags);
+ return 0;
+err0:
+ cdns3_gadget_exit(cdns);
+ return ret;
+}
+
+static int cdns3_gadget_suspend(struct cdns3 *cdns, bool do_wakeup)
+{
+ cdns3_gadget_disable(cdns);
+ return 0;
+}
+
+static int cdns3_gadget_resume(struct cdns3 *cdns, bool hibernated)
+{
+ struct cdns3_device *priv_dev;
+ unsigned long flags;
+
+ priv_dev = cdns->gadget_dev;
+ spin_lock_irqsave(&priv_dev->lock, flags);
+
+ if (!priv_dev->gadget_driver) {
+ spin_unlock_irqrestore(&priv_dev->lock, flags);
+ return 0;
+ }
+
+ cdns3_gadget_config(priv_dev);
+ spin_unlock_irqrestore(&priv_dev->lock, flags);
+ return 0;
+}
+
+/**
+ * cdns3_gadget_init - initialize device structure
+ *
+ * cdns: cdns3 instance
+ *
+ * This function initializes the gadget.
+ */
+int cdns3_gadget_init(struct cdns3 *cdns)
+{
+ struct cdns3_role_driver *rdrv;
+
+ rdrv = devm_kzalloc(cdns->dev, sizeof(*rdrv), GFP_KERNEL);
+ if (!rdrv)
+ return -ENOMEM;
+
+ rdrv->start = __cdns3_gadget_init;
+ rdrv->stop = cdns3_gadget_exit;
+ rdrv->suspend = cdns3_gadget_suspend;
+ rdrv->resume = cdns3_gadget_resume;
+ rdrv->state = CDNS3_ROLE_STATE_INACTIVE;
+ rdrv->name = "gadget";
+ cdns->roles[CDNS3_ROLE_GADGET] = rdrv;
+
+ return 0;
+}
diff --git a/drivers/usb/cdns3/gadget.h b/drivers/usb/cdns3/gadget.h
new file mode 100644
index 000000000000..db398dff65fc
--- /dev/null
+++ b/drivers/usb/cdns3/gadget.h
@@ -0,0 +1,1177 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * USBSS device controller driver header file
+ *
+ * Copyright (C) 2018 Cadence.
+ * Copyright (C) 2017-2018 NXP
+ *
+ * Author: Pawel Laszczak <[email protected]>
+ * Pawel Jez <[email protected]>
+ * Peter Chen <[email protected]>
+ */
+#ifndef __LINUX_CDNS3_GADGET
+#define __LINUX_CDNS3_GADGET
+#include <linux/usb/gadget.h>
+
+/*
+ * USBSS-DEV register interface.
+ * This corresponds to the USBSS Device Controller Interface
+ */
+
+/**
+ * struct cdns3_usb_regs - device controller registers.
+ * @usb_conf: Global Configuration Register.
+ * @usb_sts: Global Status Register.
+ * @usb_cmd: Global Command Register.
+ * @usb_iptn: ITP/SOF number Register.
+ * @usb_lpm: Global Command Register.
+ * @usb_ien: USB Interrupt Enable Register.
+ * @usb_ists: USB Interrupt Status Register.
+ * @ep_sel: Endpoint Select Register.
+ * @ep_traddr: Endpoint Transfer Ring Address Register.
+ * @ep_cfg: Endpoint Configuration Register.
+ * @ep_cmd: Endpoint Command Register.
+ * @ep_sts: Endpoint Status Register.
+ * @ep_sts_sid: Endpoint Status Register.
+ * @ep_sts_en: Endpoint Status Register Enable.
+ * @drbl: Doorbell Register.
+ * @ep_ien: EP Interrupt Enable Register.
+ * @ep_ists: EP Interrupt Status Register.
+ * @usb_pwr: Global Power Configuration Register.
+ * @usb_conf2: Global Configuration Register 2.
+ * @usb_cap1: Capability Register 1.
+ * @usb_cap2: Capability Register 2.
+ * @usb_cap3: Capability Register 3.
+ * @usb_cap4: Capability Register 4.
+ * @usb_cap5: Capability Register 5.
+ * @usb_cap6: Capability Register 6.
+ * @usb_cpkt1: Custom Packet Register 1.
+ * @usb_cpkt2: Custom Packet Register 2.
+ * @usb_cpkt3: Custom Packet Register 3.
+ * @reserved1: Reserved.
+ * @cfg_regs: Configuration registers.
+ * @reserved2: Reserved.
+ * @dma_axi_ctrl: AXI Control register.
+ * @dma_axi_id: AXI ID register.
+ * @dma_axi_cap: AXI Capability register.
+ * @dma_axi_ctrl0: AXI Control 0 register.
+ * @dma_axi_ctrl1: AXI Control 1 register.
+ */
+struct cdns3_usb_regs {
+ __le32 usb_conf;
+ __le32 usb_sts;
+ __le32 usb_cmd;
+ __le32 usb_iptn;
+ __le32 usb_lpm;
+ __le32 usb_ien;
+ __le32 usb_ists;
+ __le32 ep_sel;
+ __le32 ep_traddr;
+ __le32 ep_cfg;
+ __le32 ep_cmd;
+ __le32 ep_sts;
+ __le32 ep_sts_sid;
+ __le32 ep_sts_en;
+ __le32 drbl;
+ __le32 ep_ien;
+ __le32 ep_ists;
+ __le32 usb_pwr;
+ __le32 usb_conf2;
+ __le32 usb_cap1;
+ __le32 usb_cap2;
+ __le32 usb_cap3;
+ __le32 usb_cap4;
+ __le32 usb_cap5;
+ __le32 usb_cap6;
+ __le32 usb_cpkt1;
+ __le32 usb_cpkt2;
+ __le32 usb_cpkt3;
+ __le32 reserved1[36];
+ __le32 cfg_reg1;
+ __le32 dbg_link1;
+ __le32 dbg_link2;
+ __le32 cfg_regs[74];
+ __le32 reserved2[34];
+ __le32 dma_axi_ctrl;
+ __le32 dma_axi_id;
+ __le32 dma_axi_cap;
+ __le32 dma_axi_ctrl0;
+ __le32 dma_axi_ctrl1;
+};
+
+/* USB_CONF - bitmasks */
+/* Reset USB device configuration. */
+#define USB_CONF_CFGRST BIT(0)
+/* Set Configuration. */
+#define USB_CONF_CFGSET BIT(1)
+/* Disconnect USB device in SuperSpeed. */
+#define USB_CONF_USB3DIS BIT(3)
+/* Disconnect USB device in HS/FS */
+#define USB_CONF_USB2DIS BIT(4)
+/* Little Endian access - default */
+#define USB_CONF_LENDIAN BIT(5)
+/*
+ * Big Endian access. Driver assume that byte order for
+ * SFRs access always is as Little Endian so this bit
+ * is not used.
+ */
+#define USB_CONF_BENDIAN BIT(6)
+/* Device software reset. */
+#define USB_CONF_SWRST BIT(7)
+/* Singular DMA transfer mode. */
+#define USB_CONF_DSING BIT(8)
+/* Multiple DMA transfers mode. */
+#define USB_CONF_DMULT BIT(9)
+/* DMA clock turn-off enable. */
+#define USB_CONF_DMAOFFEN BIT(10)
+/* DMA clock turn-off disable. */
+#define USB_CONF_DMAOFFDS BIT(11)
+/* Clear Force Full Speed. */
+#define USB_CONF_CFORCE_FS BIT(12)
+/* Set Force Full Speed. */
+#define USB_CONF_SFORCE_FS BIT(13)
+/* Device enable. */
+#define USB_CONF_DEVEN BIT(14)
+/* Device disable. */
+#define USB_CONF_DEVDS BIT(15)
+/* L1 LPM state entry enable (used in HS/FS mode). */
+#define USB_CONF_L1EN BIT(16)
+/* L1 LPM state entry disable (used in HS/FS mode). */
+#define USB_CONF_L1DS BIT(17)
+/* USB 2.0 clock gate disable. */
+#define USB_CONF_CLK2OFFEN BIT(18)
+/* USB 2.0 clock gate enable. */
+#define USB_CONF_CLK2OFFDS BIT(19)
+/* L0 LPM state entry request (used in HS/FS mode). */
+#define USB_CONF_LGO_L0 BIT(20)
+/* USB 3.0 clock gate disable. */
+#define USB_CONF_CLK3OFFEN BIT(21)
+/* USB 3.0 clock gate enable. */
+#define USB_CONF_CLK3OFFDS BIT(22)
+/* Bit 23 is reserved*/
+/* U1 state entry enable (used in SS mode). */
+#define USB_CONF_U1EN BIT(24)
+/* U1 state entry disable (used in SS mode). */
+#define USB_CONF_U1DS BIT(25)
+/* U2 state entry enable (used in SS mode). */
+#define USB_CONF_U2EN BIT(26)
+/* U2 state entry disable (used in SS mode). */
+#define USB_CONF_U2DS BIT(27)
+/* U0 state entry request (used in SS mode). */
+#define USB_CONF_LGO_U0 BIT(28)
+/* U1 state entry request (used in SS mode). */
+#define USB_CONF_LGO_U1 BIT(29)
+/* U2 state entry request (used in SS mode). */
+#define USB_CONF_LGO_U2 BIT(30)
+/* SS.Inactive state entry request (used in SS mode) */
+#define USB_CONF_LGO_SSINACT BIT(31)
+
+/* USB_STS - bitmasks */
+/*
+ * Configuration status.
+ * 1 - device is in the configured state.
+ * 0 - device is not configured.
+ */
+#define USB_STS_CFGSTS_MASK BIT(0)
+#define USB_STS_CFGSTS(p) ((p) & USB_STS_CFGSTS_MASK)
+/*
+ * On-chip memory overflow.
+ * 0 - On-chip memory status OK.
+ * 1 - On-chip memory overflow.
+ */
+#define USB_STS_OV_MASK BIT(1)
+#define USB_STS_OV(p) ((p) & USB_STS_OV_MASK)
+/*
+ * SuperSpeed connection status.
+ * 0 - USB in SuperSpeed mode disconnected.
+ * 1 - USB in SuperSpeed mode connected.
+ */
+#define USB_STS_USB3CONS_MASK BIT(2)
+#define USB_STS_USB3CONS(p) ((p) & USB_STS_USB3CONS_MASK)
+/*
+ * DMA transfer configuration status.
+ * 0 - single request.
+ * 1 - multiple TRB chain
+ */
+#define USB_STS_DTRANS_MASK BIT(3)
+#define USB_STS_DTRANS(p) ((p) & USB_STS_DTRANS_MASK)
+/*
+ * Device speed.
+ * 0 - Undefined (value after reset).
+ * 1 - Low speed
+ * 2 - Full speed
+ * 3 - High speed
+ * 4 - Super speed
+ */
+#define USB_STS_USBSPEED_MASK GENMASK(6, 4)
+#define USB_STS_USBSPEED(p) (((p) & USB_STS_USBSPEED_MASK) >> 4)
+#define USB_STS_LS (0x1 << 4)
+#define USB_STS_FS (0x2 << 4)
+#define USB_STS_HS (0x3 << 4)
+#define USB_STS_SS (0x4 << 4)
+#define DEV_UNDEFSPEED(p) (((p) & USB_STS_USBSPEED_MASK) == (0x0 << 4))
+#define DEV_LOWSPEED(p) (((p) & USB_STS_USBSPEED_MASK) == USB_STS_LS)
+#define DEV_FULLSPEED(p) (((p) & USB_STS_USBSPEED_MASK) == USB_STS_FS)
+#define DEV_HIGHSPEED(p) (((p) & USB_STS_USBSPEED_MASK) == USB_STS_HS)
+#define DEV_SUPERSPEED(p) (((p) & USB_STS_USBSPEED_MASK) == USB_STS_SS)
+/*
+ * Endianness for SFR access.
+ * 0 - Little Endian order (default after hardware reset).
+ * 1 - Big Endian order
+ */
+#define USB_STS_ENDIAN_MASK BIT(7)
+#define USB_STS_ENDIAN(p) ((p) & USB_STS_ENDIAN_MASK)
+/*
+ * HS/FS clock turn-off status.
+ * 0 - hsfs clock is always on.
+ * 1 - hsfs clock turn-off in L2 (HS/FS mode) is enabled
+ * (default after hardware reset).
+ */
+#define USB_STS_CLK2OFF_MASK BIT(8)
+#define USB_STS_CLK2OFF(p) ((p) & USB_STS_CLK2OFF_MASK)
+/*
+ * PCLK clock turn-off status.
+ * 0 - pclk clock is always on.
+ * 1 - pclk clock turn-off in U3 (SS mode) is enabled
+ * (default after hardware reset).
+ */
+#define USB_STS_CLK3OFF_MASK BIT(9)
+#define USB_STS_CLK3OFF(p) ((p) & USB_STS_CLK3OFF_MASK)
+/*
+ * Controller in reset state.
+ * 0 - Internal reset is active.
+ * 1 - Internal reset is not active and controller is fully operational.
+ */
+#define USB_STS_IN_RST_MASK BIT(10)
+#define USB_STS_IN_RST(p) ((p) & USB_STS_IN_RST_MASK)
+/*
+ * Device enable Status.
+ * 0 - USB device is disabled (VBUS input is disconnected from internal logic).
+ * 1 - USB device is enabled (VBUS input is connected to the internal logic).
+ */
+#define USB_STS_DEVS_MASK BIT(14)
+#define USB_STS_DEVS(p) ((p) & USB_STS_DEVS_MASK)
+/*
+ * DAddress statuss.
+ * 0 - USB device is default state.
+ * 1 - USB device is at least in address state.
+ */
+#define USB_STS_ADDRESSED_MASK BIT(15)
+#define USB_STS_ADDRESSED(p) ((p) & USB_STS_ADDRESSED_MASK)
+/*
+ * L1 LPM state enable status (used in HS/FS mode).
+ * 0 - Entering to L1 LPM state disabled.
+ * 1 - Entering to L1 LPM state enabled.
+ */
+#define USB_STS_L1ENS_MASK BIT(16)
+#define USB_STS_L1ENS(p) ((p) & USB_STS_L1ENS_MASK)
+/*
+ * Internal VBUS connection status (used both in HS/FS and SS mode).
+ * 0 - internal VBUS is not detected.
+ * 1 - internal VBUS is detected.
+ */
+#define USB_STS_VBUSS_MASK BIT(17)
+#define USB_STS_VBUSS(p) ((p) & USB_STS_VBUSS_MASK)
+/*
+ * HS/FS LPM state (used in FS/HS mode).
+ * 0 - L0 State
+ * 1 - L1 State
+ * 2 - L2 State
+ * 3 - L3 State
+ */
+#define USB_STS_LPMST_MASK GENMASK(19, 18)
+#define DEV_L0_STATE(p) (((p) & USB_STS_LPMST_MASK) == (0x0 << 18))
+#define DEV_L1_STATE(p) (((p) & USB_STS_LPMST_MASK) == (0x1 << 18))
+#define DEV_L2_STATE(p) (((p) & USB_STS_LPMST_MASK) == (0x2 << 18))
+#define DEV_L3_STATE(p) (((p) & USB_STS_LPMST_MASK) == (0x3 << 18))
+/*
+ * Disable HS status (used in FS/HS mode).
+ * 0 - the disconnect bit for HS/FS mode is set .
+ * 1 - the disconnect bit for HS/FS mode is not set.
+ */
+#define USB_STS_USB2CONS_MASK BIT(20)
+#define USB_STS_USB2CONS(p) ((p) & USB_STS_USB2CONS_MASK)
+/*
+ * HS/FS mode connection status (used in FS/HS mode).
+ * 0 - High Speed operations in USB2.0 (FS/HS) mode not disabled.
+ * 1 - High Speed operations in USB2.0 (FS/HS).
+ */
+#define USB_STS_DISABLE_HS_MASK BIT(21)
+#define USB_STS_DISABLE_HS(p) ((p) & USB_STS_DISABLE_HS_MASK)
+/*
+ * U1 state enable status (used in SS mode).
+ * 0 - Entering to U1 state disabled.
+ * 1 - Entering to U1 state enabled.
+ */
+#define USB_STS_U1ENS_MASK BIT(24)
+#define USB_STS_U1ENS(p) ((p) & USB_STS_U1ENS_MASK)
+/*
+ * U2 state enable status (used in SS mode).
+ * 0 - Entering to U2 state disabled.
+ * 1 - Entering to U2 state enabled.
+ */
+#define USB_STS_U2ENS_MASK BIT(25)
+#define USB_STS_U2ENS(p) ((p) & USB_STS_U2ENS_MASK)
+/*
+ * SuperSpeed Link LTSSM state. This field reflects USBSS-DEV current
+ * SuperSpeed link state
+ */
+#define USB_STS_LST_MASK GENMASK(29, 26)
+#define DEV_LST_U0 (((p) & USB_STS_LST_MASK) == (0x0 << 26))
+#define DEV_LST_U1 (((p) & USB_STS_LST_MASK) == (0x1 << 26))
+#define DEV_LST_U2 (((p) & USB_STS_LST_MASK) == (0x2 << 26))
+#define DEV_LST_U3 (((p) & USB_STS_LST_MASK) == (0x3 << 26))
+#define DEV_LST_DISABLED (((p) & USB_STS_LST_MASK) == (0x4 << 26))
+#define DEV_LST_RXDETECT (((p) & USB_STS_LST_MASK) == (0x5 << 26))
+#define DEV_LST_INACTIVE (((p) & USB_STS_LST_MASK) == (0x6 << 26))
+#define DEV_LST_POLLING (((p) & USB_STS_LST_MASK) == (0x7 << 26))
+#define DEV_LST_RECOVERY (((p) & USB_STS_LST_MASK) == (0x8 << 26))
+#define DEV_LST_HOT_RESET (((p) & USB_STS_LST_MASK) == (0x9 << 26))
+#define DEV_LST_COMP_MODE (((p) & USB_STS_LST_MASK) == (0xa << 26))
+#define DEV_LST_LB_STATE (((p) & USB_STS_LST_MASK) == (0xb << 26))
+/*
+ * DMA clock turn-off status.
+ * 0 - DMA clock is always on (default after hardware reset).
+ * 1 - DMA clock turn-off in U1, U2 and U3 (SS mode) is enabled.
+ */
+#define USB_STS_DMAOFF_MASK BIT(30)
+#define USB_STS_DMAOFF(p) ((p) & USB_STS_DMAOFF_MASK)
+/*
+ * SFR Endian statuss.
+ * 0 - Little Endian order (default after hardware reset).
+ * 1 - Big Endian order.
+ */
+#define USB_STS_ENDIAN2_MASK BIT(31)
+#define USB_STS_ENDIAN2(p) ((p) & USB_STS_ENDIAN2_MASK)
+
+/* USB_CMD - bitmasks */
+/* Set Function Address */
+#define USB_CMD_SET_ADDR BIT(0)
+/*
+ * Function Address This field is saved to the device only when the field
+ * SET_ADDR is set '1 ' during write to USB_CMD register.
+ * Software is responsible for entering the address of the device during
+ * SET_ADDRESS request service. This field should be set immediately after
+ * the SETUP packet is decoded, and prior to confirmation of the status phase
+ */
+#define USB_CMD_FADDR_MASK GENMASK(7, 1)
+#define USB_CMD_FADDR(p) (((p) << 1) & USB_CMD_FADDR_MASK)
+/* Send Function Wake Device Notification TP (used only in SS mode). */
+#define USB_CMD_SDNFW BIT(8)
+/* Set Test Mode (used only in HS/FS mode). */
+#define USB_CMD_STMODE BIT(9)
+/* Test mode selector (used only in HS/FS mode) */
+#define USB_STS_TMODE_SEL_MASK GENMASK(11, 10)
+#define USB_STS_TMODE_SEL(p) (((p) << 10) & USB_STS_TMODE_SEL_MASK)
+/*
+ * Send Latency Tolerance Message Device Notification TP (used only
+ * in SS mode).
+ */
+#define USB_CMD_SDNLTM BIT(12)
+/* Send Custom Transaction Packet (used only in SS mode) */
+#define USB_CMD_SPKT BIT(13)
+/*Device Notification 'Function Wake' - Interface value (only in SS mode. */
+#define USB_CMD_DNFW_INT_MASK GENMASK(23, 16)
+#define USB_STS_DNFW_INT(p) (((p) << 16) & USB_CMD_DNFW_INT_MASK)
+/*
+ * Device Notification 'Latency Tolerance Message' -373 BELT value [7:0]
+ * (used only in SS mode).
+ */
+#define USB_CMD_DNLTM_BELT_MASK GENMASK(27, 16)
+#define USB_STS_DNLTM_BELT(p) (((p) << 16) & USB_CMD_DNLTM_BELT_MASK)
+
+/* USB_ITPN - bitmasks */
+/*
+ * ITP(SS) / SOF (HS/FS) number
+ * In SS mode this field represent number of last ITP received from host.
+ * In HS/FS mode this field represent number of last SOF received from host.
+ */
+#define USB_ITPN_MASK GENMASK(13, 0)
+#define USB_ITPN(p) ((p) & USB_ITPN_MASK)
+
+/* USB_LPM - bitmasks */
+/* Host Initiated Resume Duration. */
+#define USB_LPM_HIRD_MASK GENMASK(3, 0)
+#define USB_LPM_HIRD(p) ((p) & USB_LPM_HIRD_MASK)
+/* Remote Wakeup Enable (bRemoteWake). */
+#define USB_LPM_BRW BIT(4)
+
+/* USB_IEN - bitmasks */
+/* SS connection interrupt enable */
+#define USB_IEN_CONIEN BIT(0)
+/* SS disconnection interrupt enable. */
+#define USB_IEN_DISIEN BIT(1)
+/* USB SS warm reset interrupt enable. */
+#define USB_IEN_UWRESIEN BIT(2)
+/* USB SS hot reset interrupt enable */
+#define USB_IEN_UHRESIEN BIT(3)
+/* SS link U3 state enter interrupt enable (suspend).*/
+#define USB_IEN_U3ENTIEN BIT(4)
+/* SS link U3 state exit interrupt enable (wakeup). */
+#define USB_IEN_U3EXTIEN BIT(5)
+/* SS link U2 state enter interrupt enable.*/
+#define USB_IEN_U2ENTIEN BIT(6)
+/* SS link U2 state exit interrupt enable.*/
+#define USB_IEN_U2EXTIEN BIT(7)
+/* SS link U1 state enter interrupt enable.*/
+#define USB_IEN_U1ENTIEN BIT(8)
+/* SS link U1 state exit interrupt enable.*/
+#define USB_IEN_U1EXTIEN BIT(9)
+/* ITP/SOF packet detected interrupt enable.*/
+#define USB_IEN_ITPIEN BIT(10)
+/* Wakeup interrupt enable.*/
+#define USB_IEN_WAKEIEN BIT(11)
+/* Send Custom Packet interrupt enable.*/
+#define USB_IEN_SPKTIEN BIT(12)
+/* HS/FS mode connection interrupt enable.*/
+#define USB_IEN_CON2IEN BIT(16)
+/* HS/FS mode disconnection interrupt enable.*/
+#define USB_IEN_DIS2IEN BIT(17)
+/* USB reset (HS/FS mode) interrupt enable.*/
+#define USB_IEN_U2RESIEN BIT(18)
+/* LPM L2 state enter interrupt enable.*/
+#define USB_IEN_L2ENTIEN BIT(20)
+/* LPM L2 state exit interrupt enable.*/
+#define USB_IEN_L2EXTIEN BIT(21)
+/* LPM L1 state enter interrupt enable.*/
+#define USB_IEN_L1ENTIEN BIT(24)
+/* LPM L1 state exit interrupt enable.*/
+#define USB_IEN_L1EXTIEN BIT(25)
+/* Configuration reset interrupt enable.*/
+#define USB_IEN_CFGRESIEN BIT(26)
+/* Start of the USB SS warm reset interrupt enable.*/
+#define USB_IEN_UWRESSIEN BIT(28)
+/* End of the USB SS warm reset interrupt enable.*/
+#define USB_IEN_UWRESEIEN BIT(29)
+
+#define USB_IEN_INIT (USB_IEN_U2RESIEN | USB_ISTS_DIS2I | USB_IEN_CON2IEN \
+ | USB_IEN_UHRESIEN | USB_IEN_UWRESIEN | USB_IEN_DISIEN \
+ | USB_IEN_CONIEN | USB_IEN_U3EXTIEN | USB_IEN_L2ENTIEN \
+ | USB_IEN_L2EXTIEN)
+
+/* USB_ISTS - bitmasks */
+/* SS Connection detected. */
+#define USB_ISTS_CONI BIT(0)
+/* SS Disconnection detected. */
+#define USB_ISTS_DISI BIT(1)
+/* UUSB warm reset detectede. */
+#define USB_ISTS_UWRESI BIT(2)
+/* USB hot reset detected. */
+#define USB_ISTS_UHRESI BIT(3)
+/* U3 link state enter detected (suspend).*/
+#define USB_ISTS_U3ENTI BIT(4)
+/* U3 link state exit detected (wakeup). */
+#define USB_ISTS_U3EXTI BIT(5)
+/* U2 link state enter detected.*/
+#define USB_ISTS_U2ENTI BIT(6)
+/* U2 link state exit detected.*/
+#define USB_ISTS_U2EXTI BIT(7)
+/* U1 link state enter detected.*/
+#define USB_ISTS_U1ENTI BIT(8)
+/* U1 link state exit detected.*/
+#define USB_ISTS_U1EXTI BIT(9)
+/* ITP/SOF packet detected.*/
+#define USB_ISTS_ITPI BIT(10)
+/* Wakeup detected.*/
+#define USB_ISTS_WAKEI BIT(11)
+/* Send Custom Packet detected.*/
+#define USB_ISTS_SPKTI BIT(12)
+/* HS/FS mode connection detected.*/
+#define USB_ISTS_CON2I BIT(16)
+/* HS/FS mode disconnection detected.*/
+#define USB_ISTS_DIS2I BIT(17)
+/* USB reset (HS/FS mode) detected.*/
+#define USB_ISTS_U2RESI BIT(18)
+/* LPM L2 state enter detected.*/
+#define USB_ISTS_L2ENTI BIT(20)
+/* LPM L2 state exit detected.*/
+#define USB_ISTS_L2EXTI BIT(21)
+/* LPM L1 state enter detected.*/
+#define USB_ISTS_L1ENTI BIT(24)
+/* LPM L1 state exit detected.*/
+#define USB_ISTS_L1EXTI BIT(25)
+/* USB configuration reset detected.*/
+#define USB_ISTS_CFGRESI BIT(26)
+/* Start of the USB warm reset detected.*/
+#define USB_ISTS_UWRESSI BIT(28)
+/* End of the USB warm reset detected.*/
+#define USB_ISTS_UWRESEI BIT(29)
+
+/* USB_SEL - bitmasks */
+#define EP_SEL_EPNO_MASK GENMASK(3, 0)
+/* Endpoint number. */
+#define EP_SEL_EPNO(p) ((p) & EP_SEL_EPNO_MASK)
+/* Endpoint direction bit - 0 - OUT, 1 - IN. */
+#define EP_SEL_DIR BIT(7)
+
+#define select_ep_in(nr) (EP_SEL_EPNO(p) | EP_SEL_DIR)
+#define select_ep_out (EP_SEL_EPNO(p))
+
+/* EP_TRADDR - bitmasks */
+/* Transfer Ring address. */
+#define EP_TRADDR_TRADDR(p) ((p))
+
+/* EP_CFG - bitmasks */
+/* Endpoint enable */
+#define EP_CFG_ENABLE BIT(0)
+/*
+ * Endpoint type.
+ * 1 - isochronous
+ * 2 - bulk
+ * 3 - interrupt
+ */
+#define EP_CFG_EPTYPE_MASK GENMASK(2, 1)
+#define EP_CFG_EPTYPE(p) (((p) << 1) & EP_CFG_EPTYPE_MASK)
+/* Stream support enable (only in SS mode). */
+#define EP_CFG_STREAM_EN BIT(3)
+/* TDL check (only in SS mode for BULK EP). */
+#define EP_CFG_TDL_CHK BIT(4)
+/* SID check (only in SS mode for BULK OUT EP). */
+#define EP_CFG_SID_CHK BIT(5)
+/* DMA transfer endianness. */
+#define EP_CFG_EPENDIAN BIT(7)
+/* Max burst size (used only in SS mode). */
+#define EP_CFG_MAXBURST_MASK GENMASK(11, 8)
+#define EP_CFG_MAXBURST(p) (((p) << 8) & EP_CFG_MAXBURST_MASK)
+/* ISO max burst. */
+#define EP_CFG_MULT_MASK GENMASK(15, 14)
+#define EP_CFG_MULT(p) (((p) << 14) & EP_CFG_MULT)
+/* ISO max burst. */
+#define EP_CFG_MAXPKTSIZE_MASK GENMASK(26, 16)
+#define EP_CFG_MAXPKTSIZE(p) (((p) << 16) & EP_CFG_MAXPKTSIZE_MASK)
+/* Max number of buffered packets. */
+#define EP_CFG_BUFFERING_MASK GENMASK(31, 27)
+#define EP_CFG_BUFFERING(p) (((p) << 27) & EP_CFG_BUFFERING_MASK)
+
+/* EP_CMD - bitmasks */
+/* Endpoint reset. */
+#define EP_CMD_EPRST BIT(0)
+/* Endpoint STALL set. */
+#define EP_CMD_SSTALL BIT(1)
+/* Endpoint STALL clear. */
+#define EP_CMD_CSTALL BIT(2)
+/* Send ERDY TP. */
+#define EP_CMD_ERDY BIT(3)
+/* Request complete. */
+#define EP_CMD_REQ_CMPL BIT(5)
+/* Transfer descriptor ready. */
+#define EP_CMD_DRDY BIT(6)
+/* Data flush. */
+#define EP_CMD_DFLUSH BIT(7)
+/*
+ * Transfer Descriptor Length write (used only for Bulk Stream capable
+ * endpoints in SS mode).
+ */
+#define EP_CMD_STDL BIT(8)
+/* Transfer Descriptor Length (used only in SS mode for bulk endpoints). */
+#define EP_CMD_TDL_MASK GENMASK(15, 9)
+#define EP_CMD_TDL(p) (((p) << 9) & EP_CMD_TDL_MASK)
+/* ERDY Stream ID value (used in SS mode). */
+#define EP_CMD_ERDY_SID_MASK GENMASK(31, 16)
+#define EP_CMD_ERDY_SID(p) (((p) << 16) & EP_CMD_SID_MASK)
+
+/* EP_STS - bitmasks */
+/* Setup transfer complete. */
+#define EP_STS_SETUP BIT(0)
+/* Endpoint STALL status. */
+#define EP_STS_STALL(p) ((p) & BIT(1))
+/* Interrupt On Complete. */
+#define EP_STS_IOC BIT(2)
+/* Interrupt on Short Packet. */
+#define EP_STS_ISP BIT(3)
+/* Transfer descriptor missing. */
+#define EP_STS_DESCMIS BIT(4)
+/* Stream Rejected (used only in SS mode) */
+#define EP_STS_STREAMR BIT(5)
+/* EXIT from MOVE DATA State (used only for stream transfers in SS mode). */
+#define EP_STS_MD_EXIT BIT(6)
+/* TRB error. */
+#define EP_STS_TRBERR BIT(7)
+/* Not ready (used only in SS mode). */
+#define EP_STS_NRDY BIT(8)
+/* DMA busy. */
+#define EP_STS_DBUSY(p) ((p) & BIT(9))
+/* Endpoint Buffer Empty */
+#define EP_STS_BUFFEMPTY(p) ((p) & BIT(10))
+/* Current Cycle Status */
+#define EP_STS_CCS(p) ((p) & BIT(11))
+/* Prime (used only in SS mode. */
+#define EP_STS_PRIME BIT(12)
+/* Stream error (used only in SS mode). */
+#define EP_STS_SIDERR BIT(13)
+/* OUT size mismatch. */
+#define EP_STS_OUTSMM BIT(14)
+/* ISO transmission error. */
+#define EP_STS_ISOERR BIT(15)
+/* Host Packet Pending (only for SS mode). */
+#define EP_STS_HOSTPP(p) ((p) & BIT(16))
+/* Stream Protocol State Machine State (only for Bulk stream endpoints). */
+#define EP_STS_SPSMST_MASK GENMASK(18, 17)
+#define EP_STS_SPSMST_DISABLED(p) (((p) & EP_STS_SPSMST_MASK) >> 17)
+#define EP_STS_SPSMST_IDLE(p) (((p) & EP_STS_SPSMST_MASK) >> 17)
+#define EP_STS_SPSMST_START_STREAM(p) (((p) & EP_STS_SPSMST_MASK) >> 17)
+#define EP_STS_SPSMST_MOVE_DATA(p) (((p) & EP_STS_SPSMST_MASK) >> 17)
+/* Interrupt On Transfer complete. */
+#define EP_STS_IOT BIT(19)
+/* OUT queue endpoint number. */
+#define EP_STS_OUTQ_NO_MASK GENMASK(27, 24)
+#define EP_STS_OUTQ_NO(p) (((p) & EP_STS_OUTQ_NO_MASK) >> 24)
+/* OUT queue valid flag. */
+#define EP_STS_OUTQ_VAL_MASK BIT(28)
+#define EP_STS_OUTQ_VAL(p) ((p) & EP_STS_OUTQ_VAL_MASK)
+/* SETUP WAIT. */
+#define EP_STS_STPWAIT BIT(31)
+
+/* EP_STS_SID - bitmasks */
+/* Stream ID (used only in SS mode). */
+#define EP_STS_SID_MASK GENMASK(15, 0)
+#define EP_STS_SID(p) ((p) & EP_STS_SID_MASK)
+
+/* EP_STS_EN - bitmasks */
+/* SETUP interrupt enable. */
+#define EP_STS_EN_SETUPEN BIT(0)
+/* OUT transfer missing descriptor enable. */
+#define EP_STS_EN_DESCMISEN BIT(4)
+/* Stream Rejected enable. */
+#define EP_STS_EN_STREAMREN BIT(5)
+/* Move Data Exit enable.*/
+#define EP_STS_EN_MD_EXITEN BIT(6)
+/* TRB enable. */
+#define EP_STS_EN_TRBERREN BIT(7)
+/* NRDY enable. */
+#define EP_STS_EN_NRDYEN BIT(8)
+/* Prime enable. */
+#define EP_STS_EN_PRIMEEEN BIT(12)
+/* Stream error enable. */
+#define EP_STS_EN_SIDERREN BIT(13)
+/* OUT size mismatch enable. */
+#define EP_STS_EN_OUTSMMEN BIT(14)
+/* ISO transmission error enable. */
+#define EP_STS_EN_ISOERREN BIT(15)
+/* Interrupt on Transmission complete enable. */
+#define EP_STS_EN_IOTEN BIT(19)
+/* Setup Wait interrupt enable. */
+#define EP_STS_EN_STPWAITEN BIT(31)
+
+/* DRBL- bitmasks */
+#define DB_VALUE_BY_INDEX(index) (1 << (index))
+#define DB_VALUE_EP0_OUT BIT(0)
+#define DB_VALUE_EP0_IN BIT(16)
+
+/* EP_IEN - bitmasks */
+#define EP_IEN(index) (1 << (index))
+#define EP_IEN_EP_OUT0 BIT(0)
+#define EP_IEN_EP_IN0 BIT(16)
+
+/* EP_ISTS - bitmasks */
+#define EP_ISTS(index) (1 << (index))
+#define EP_ISTS_EP_OUT0 BIT(0)
+#define EP_ISTS_EP_IN0 BIT(16)
+
+/* EP_PWR- bitmasks */
+/*Power Shut Off capability enable*/
+#define PUSB_PWR_PSO_EN BIT(0)
+/*Power Shut Off capability disable*/
+#define PUSB_PWR_PSO_DS BIT(1)
+/*
+ * Enables turning-off Reference Clock.
+ * This bit is optional and implemented only when support for OTG is
+ * implemented (indicated by OTG_READY bit set to '1').
+ */
+#define PUSB_PWR_STB_CLK_SWITCH_EN BIT(8)
+/*
+ * Status bit indicating that operation required by STB_CLK_SWITCH_EN write
+ * is completed
+ */
+#define PUSB_PWR_STB_CLK_SWITCH_DONE BIT(9)
+/* This bit informs if Fast Registers Access is enabled. */
+#define PUSB_PWR_FST_REG_ACCESS_STAT BIT(30)
+/* Fast Registers Access Enable. */
+#define PUSB_PWR_FST_REG_ACCESS BIT(31)
+
+/* USB_CAP1- bitmasks */
+/*
+ * SFR Interface type
+ * These field reflects type of SFR interface implemented:
+ * 0x0 - OCP
+ * 0x1 - AHB,
+ * 0x2 - PLB
+ * 0x3 - AXI
+ * 0x4-0xF - reserved
+ */
+#define USB_CAP1_SFR_TYPE_MASK GENMASK(3, 0)
+#define DEV_SFR_TYPE_OCP(p) (((p) & USB_CAP1_SFR_TYPE_MASK) == 0x0)
+#define DEV_SFR_TYPE_AHB(p) (((p) & USB_CAP1_SFR_TYPE_MASK) == 0x1)
+#define DEV_SFR_TYPE_PLB(p) (((p) & USB_CAP1_SFR_TYPE_MASK) == 0x2)
+#define DEV_SFR_TYPE_AXI(p) (((p) & USB_CAP1_SFR_TYPE_MASK) == 0x3)
+/*
+ * SFR Interface width
+ * These field reflects width of SFR interface implemented:
+ * 0x0 - 8 bit interface,
+ * 0x1 - 16 bit interface,
+ * 0x2 - 32 bit interface
+ * 0x3 - 64 bit interface
+ * 0x4-0xF - reserved
+ */
+#define USB_CAP1_SFR_WIDTH_MASK GENMASK(7, 4)
+#define DEV_SFR_WIDTH_8(p) (((p) & USB_CAP1_SFR_WIDTH_MASK) == (0x0 << 4))
+#define DEV_SFR_WIDTH_16(p) (((p) & USB_CAP1_SFR_WIDTH_MASK) == (0x1 << 4))
+#define DEV_SFR_WIDTH_32(p) (((p) & USB_CAP1_SFR_WIDTH_MASK) == (0x2 << 4))
+#define DEV_SFR_WIDTH_64(p) (((p) & USB_CAP1_SFR_WIDTH_MASK) == (0x3 << 4))
+/*
+ * DMA Interface type
+ * These field reflects type of DMA interface implemented:
+ * 0x0 - OCP
+ * 0x1 - AHB,
+ * 0x2 - PLB
+ * 0x3 - AXI
+ * 0x4-0xF - reserved
+ */
+#define USB_CAP1_DMA_TYPE_MASK GENMASK(11, 8)
+#define DEV_DMA_TYPE_OCP(p) (((p) & USB_CAP1_DMA_TYPE_MASK) == (0x0 << 8))
+#define DEV_DMA_TYPE_AHB(p) (((p) & USB_CAP1_DMA_TYPE_MASK) == (0x1 << 8))
+#define DEV_DMA_TYPE_PLB(p) (((p) & USB_CAP1_DMA_TYPE_MASK) == (0x2 << 8))
+#define DEV_DMA_TYPE_AXI(p) (((p) & USB_CAP1_DMA_TYPE_MASK) == (0x3 << 8))
+/*
+ * DMA Interface width
+ * These field reflects width of DMA interface implemented:
+ * 0x0 - reserved,
+ * 0x1 - reserved,
+ * 0x2 - 32 bit interface
+ * 0x3 - 64 bit interface
+ * 0x4-0xF - reserved
+ */
+#define USB_CAP1_DMA_WIDTH_MASK GENMASK(15, 12)
+#define DEV_DMA_WIDTH_32(p) (((p) & USB_CAP1_DMA_WIDTH_MASK) == (0x2 << 12))
+#define DEV_DMA_WIDTH_64(p) (((p) & USB_CAP1_DMA_WIDTH_MASK) == (0x3 << 12))
+/*
+ * USB3 PHY Interface type
+ * These field reflects type of USB3 PHY interface implemented:
+ * 0x0 - USB PIPE,
+ * 0x1 - RMMI,
+ * 0x2-0xF - reserved
+ */
+#define USB_CAP1_U3PHY_TYPE_MASK GENMASK(19, 16)
+#define DEV_U3PHY_PIPE(p) (((p) & USB_CAP1_U3PHY_TYPE_MASK) == (0x0 << 16))
+#define DEV_U3PHY_RMMI(p) (((p) & USB_CAP1_U3PHY_TYPE_MASK) == (0x1 << 16))
+/*
+ * USB3 PHY Interface width
+ * These field reflects width of USB3 PHY interface implemented:
+ * 0x0 - 8 bit PIPE interface,
+ * 0x1 - 16 bit PIPE interface,
+ * 0x2 - 32 bit PIPE interface,
+ * 0x3 - 64 bit PIPE interface
+ * 0x4-0xF - reserved
+ * Note: When SSIC interface is implemented this field shows the width of
+ * internal PIPE interface. The RMMI interface is always 20bit wide.
+ */
+#define USB_CAP1_U3PHY_WIDTH_MASK GENMASK(23, 20)
+#define DEV_U3PHY_WIDTH_8(p) \
+ (((p) & USB_CAP1_U3PHY_WIDTH_MASK) == (0x0 << 20))
+#define DEV_U3PHY_WIDTH_16(p) \
+ (((p) & USB_CAP1_U3PHY_WIDTH_MASK) == (0x1 << 16))
+#define DEV_U3PHY_WIDTH_32(p) \
+ (((p) & USB_CAP1_U3PHY_WIDTH_MASK) == (0x2 << 20))
+#define DEV_U3PHY_WIDTH_64(p) \
+ (((p) & USB_CAP1_U3PHY_WIDTH_MASK) == (0x3 << 16))
+
+/*
+ * USB2 PHY Interface enable
+ * These field informs if USB2 PHY interface is implemented:
+ * 0x0 - interface NOT implemented,
+ * 0x1 - interface implemented
+ */
+#define USB_CAP1_U2PHY_EN(p) ((p) & BIT(24))
+/*
+ * USB2 PHY Interface type
+ * These field reflects type of USB2 PHY interface implemented:
+ * 0x0 - UTMI,
+ * 0x1 - ULPI
+ */
+#define DEV_U2PHY_ULPI(p) ((p) & BIT(25))
+/*
+ * USB2 PHY Interface width
+ * These field reflects width of USB2 PHY interface implemented:
+ * 0x0 - 8 bit interface,
+ * 0x1 - 16 bit interface,
+ * Note: The ULPI interface is always 8bit wide.
+ */
+#define DEV_U2PHY_WIDTH_16(p) ((p) & BIT(26))
+/*
+ * OTG Ready
+ * 0x0 - pure device mode
+ * 0x1 - some features and ports for CDNS USB OTG controller are implemented.
+ */
+#define USB_CAP1_OTG_READY(p) ((p) & BIT(27))
+
+/* USB_CAP2- bitmasks */
+/*
+ * The actual size of the connected On-chip RAM memory in kB:
+ * - 0 means 256 kB (max supported mem size)
+ * - value other than 0 reflects the mem size in kB
+ */
+#define USB_CAP2_ACTUAL_MEM_SIZE(p) ((p) & GENMASK(7, 0))
+/*
+ * Max supported mem size
+ * These field reflects width of on-chip RAM address bus width,
+ * which determines max supported mem size:
+ * 0x0-0x7 - reserved,
+ * 0x8 - support for 4kB mem,
+ * 0x9 - support for 8kB mem,
+ * 0xA - support for 16kB mem,
+ * 0xB - support for 32kB mem,
+ * 0xC - support for 64kB mem,
+ * 0xD - support for 128kB mem,
+ * 0xE - support for 256kB mem,
+ * 0xF - reserved
+ */
+#define USB_CAP2_MAX_MEM_SIZE(p) ((p) & GENMASK(11, 8))
+
+/* USB_CAP3- bitmasks */
+#define EP_IS_IMPLEMENTED(reg, index) ((reg) & (1 << (index)))
+
+/* USB_CAP4- bitmasks */
+#define EP_SUPPORT_ISO(reg, index) ((reg) & (1 << (index)))
+
+/* USB_CAP5- bitmasks */
+#define EP_SUPPORT_STREAM(reg, index) ((reg) & (1 << (index)))
+
+/* USB_CAP6- bitmasks */
+/* The USBSS-DEV Controller Internal build number. */
+#define GET_DEV_VERSION__INTERNAL_NUMBER(p) ((p) & GENMASK(7, 0))
+/* The USBSS-DEV Controller version number. */
+#define GET_DEV_VERSION(p) ((p) & GENMASK(31, 8))
+
+/* DBG_LINK1- bitmasks */
+/*
+ * LFPS_MIN_DET_U1_EXIT value This parameter configures the minimum
+ * time required for decoding the received LFPS as an LFPS.U1_Exit.
+ */
+#define DBG_LINK1_LFPS_MIN_DET_U1_EXIT(p) ((p) & GENMASK(7, 0))
+/*
+ * LFPS_MIN_GEN_U1_EXIT value This parameter configures the minimum time for
+ * phytxelecidle deassertion when LFPS.U1_Exit
+ */
+#define DBG_LINK1_LFPS_MIN_GEN_U1_EXIT(p) (((p) << 8) & GENMASK(15, 8))
+/*
+ * RXDET_BREAK_DIS value This parameter configures terminating the Far-end
+ * Receiver termination detection sequence:
+ * 0: it is possible that USBSS_DEV will terminate Farend receiver
+ * termination detection sequence
+ * 1: USBSS_DEV will not terminate Far-end receiver termination
+ * detection sequence
+ */
+#define DBG_LINK1_RXDET_BREAK_DIS BIT(16)
+/* LFPS_GEN_PING value This parameter configures the LFPS.Ping generation */
+#define DBG_LINK1_LFPS_GEN_PING(p) (((p) << 17) & GENMASK(21, 17))
+/*
+ * Set the LFPS_MIN_DET_U1_EXIT value Writing '1' to this bit writes the
+ * LFPS_MIN_DET_U1_EXIT field value to the device. This bit is automatically
+ * cleared. Writing '0' has no effect
+ */
+#define DBG_LINK1_LFPS_MIN_DET_U1_EXIT_SET BIT(24)
+/*
+ * Set the LFPS_MIN_GEN_U1_EXIT value. Writing '1' to this bit writes the
+ * LFPS_MIN_GEN_U1_EXIT field value to the device. This bit is automatically
+ * cleared. Writing '0' has no effect
+ */
+#define DBG_LINK1_LFPS_MIN_GEN_U1_EXIT_SET BIT(25)
+/*
+ * Set the RXDET_BREAK_DIS value Writing '1' to this bit writes
+ * the RXDET_BREAK_DIS field value to the device. This bit is automatically
+ * cleared. Writing '0' has no effect
+ */
+#define DBG_LINK1_RXDET_BREAK_DIS_SET BIT(26)
+/*
+ * Set the LFPS_GEN_PING_SET value Writing '1' to this bit writes
+ * the LFPS_GEN_PING field value to the device. This bit is automatically
+ * cleared. Writing '0' has no effect."
+ */
+#define DBG_LINK1_LFPS_GEN_PING_SET BIT(27)
+
+#define gadget_to_cdns3_device(g) (container_of(g, struct cdns3_device, gadget))
+
+#define ep_to_cdns3_ep(ep) (container_of(ep, struct cdns3_endpoint, endpoint))
+
+/*-------------------------------------------------------------------------*/
+/*
+ * USBSS-DEV DMA interface .
+ */
+#define TRBS_PER_SEGMENT 16
+
+/**
+ * struct cdns3_trb - represent Transfer Descriptor block.
+ * @buffer: pointer to buffer data
+ * @length: length of data
+ * @control: control flags.
+ *
+ * This structure describes transfer block serviced by DMA module.
+ */
+struct cdns3_trb {
+ __le32 buffer;
+ __le32 length;
+ __le32 control;
+};
+
+#define TRB_SIZE (sizeof(struct cdns3_trb))
+#define TRB_RING_SIZE (TRB_SIZE * TRBS_PER_SEGMENT)
+
+/* TRB bit mask */
+#define TRB_TYPE_BITMASK GENMASK(15, 10)
+#define TRB_TYPE(p) ((p) << 10)
+#define TRB_FIELD_TO_TYPE(p) (((p) & TRB_TYPE_BITMASK) >> 10)
+
+/* TRB type IDs */
+/* bulk, interrupt, isoc , and control data stage */
+#define TRB_NORMAL 1
+/* TRB for linking ring segments */
+#define TRB_LINK 6
+
+/* Cycle bit - indicates TRB ownership by driver or hw*/
+#define TRB_CYCLE BIT(0)
+/*
+ * When set to '1', the device will toggle its interpretation of the Cycle bit
+ */
+#define TRB_TOGGLE BIT(1)
+
+/* Interrupt on short packet*/
+#define TRB_ISP BIT(2)
+/*Setting this bit enables FIFO DMA operation mode*/
+#define TRB_FIFO_MODE BIT(3)
+/* Set PCIe no snoop attribute */
+#define TRB_CHAIN BIT(4)
+/* Interrupt on completion */
+#define TRB_IOC BIT(5)
+
+/* stream ID bitmasks. */
+#define TRB_STREAM_ID(p) ((p) & GENMASK(31, 16))
+
+/* transfer_len bitmasks. */
+#define TRB_LEN(p) ((p) & GENMASK(16, 0))
+
+/* transfer_len bitmasks - bits 31:24 */
+#define TRB_BURST_LEN(p) ((p) & GENMASK(31, 24))
+
+/* Data buffer pointer bitmasks*/
+#define TRB_BUFFER(p) ((p) & GENMASK(31, 0))
+
+/*-------------------------------------------------------------------------*/
+/* Driver numeric constants */
+
+/* Such declaration should be added to ch9.h */
+#define USB_DEVICE_MAX_ADDRESS 127
+
+/* Endpoint init values */
+#define CDNS3_EP_MAX_PACKET_LIMIT 1024
+#define CDNS3_EP_MAX_STREAMS 15
+
+#define CDNS3_EP0_MAX_PACKET_LIMIT 512
+
+/* All endpoints except EP0 */
+#define CDNS3_ENDPOINTS_MAX_COUNT 30
+
+#define CDNS3_EP_ZLP_BUF_SIZE 1024
+
+/*-------------------------------------------------------------------------*/
+#define CDNS3_EP_BUF_SIZE 2 /* KB */
+#define CDNS3_ALIGNED_BUF_SIZE 16384 /* Bytes */
+#define CDNS3_DESCMIS_BUF_SIZE 65536 /* Bytes */
+/*-------------------------------------------------------------------------*/
+/* Used structs */
+
+struct cdns3_device;
+
+/**
+ * struct cdns3_endpoint - extended device side representation of USB endpoint.
+ * @endpoint: usb endpoint
+ * @request_list: list of request for this endpoint
+ * @trb_pool: transfer ring - array of transaction buffers
+ * @trb_pool_dma: dma address of transfer ring
+ * @cdns3_dev: device associated with this endpoint
+ * @name: a human readable name e.g. ep1out
+ * @flags: specify the current state of endpoint
+ * @descmis_req: internal transfer object used for getting data from on-chip
+ * buffer. It can happen only if function driver doesn't send usb_request
+ * object on time.
+ * @descmis_pending: flag specify that internal buffer was used for DMA to
+ * take data from shared on-chip buffers to avoid blocking transfer to other
+ * endpoints. It indicate that is still in progress.
+ * @descmis_finished: flag specify that transfer has armed on descriptor
+ * missing event has been completed. If function driver requests
+ * the transfer then controller driver can just return this data.
+ * @aligned_buff: aligned to 8 bytes data buffer. Buffer address used in
+ * TRB shall be aligned to 8.
+ * @aligned_dma_addr: dma address of aligned_buff
+ * @dir: endpoint direction
+ * @num: endpoint number (1 - 15)
+ * @type: set to bmAttributes & USB_ENDPOINT_XFERTYPE_MASK
+ * @free_trbs: number of free TRBs in transfer ring
+ * @pcs: producer cycle state
+ * @ccs: consumer cycle state
+ * @enqueue: enqueue index in transfer ring
+ * @dequeue: dequeue index in transfer ring
+ */
+struct cdns3_endpoint {
+ struct usb_ep endpoint;
+ struct list_head request_list;
+
+ struct cdns3_trb *trb_pool;
+ dma_addr_t trb_pool_dma;
+
+ struct cdns3_device *cdns3_dev;
+ char name[20];
+
+#define EP_ENABLED BIT(0)
+#define EP_STALL BIT(1)
+#define EP_WEDGE BIT(2)
+#define EP_TRANSFER_STARTED BIT(3)
+#define EP_UPDATE_EP_TRBADDR BIT(4)
+#define EP_PENDING_REQUEST BIT(5)
+#define EP_RING_FULL BIT(6)
+#define EP_CLAIMED BIT(5)
+ u32 flags;
+
+ struct cdns3_request *descmis_req;
+ u32 descmis_pending:1;
+ u32 descmis_finished:1;
+
+ void *aligned_buff;
+ dma_addr_t aligned_dma_addr;
+ u8 dir;
+ u8 num;
+ u8 type;
+
+ int free_trbs;
+ u8 pcs;
+ u8 ccs;
+ int enqueue;
+ int dequeue;
+};
+
+/**
+ * struct cdns3_request - extended device side representation of usb_request
+ * object .
+ * @request: generic usb_request object describing single I/O request.
+ * @priv_ep: extended representation of usb_ep object
+ * @trb: the first TRB association with this request
+ * @start_trb: number of the first TRB in transfer ring
+ * @end_trb: number of the last TRB in transfer ring
+ * @flags: flag specifying special usage of request
+ */
+struct cdns3_request {
+ struct usb_request request;
+ struct cdns3_endpoint *priv_ep;
+ struct cdns3_trb *trb;
+ int start_trb;
+ int end_trb;
+#define REQUEST_PENDING BIT(0)
+#define REQUEST_INTERNAL BIT(1)
+#define REQUEST_ZLP BIT(2)
+ u32 flags;
+};
+
+#define to_cdns3_request(r) (container_of(r, struct cdns3_request, request))
+
+/**
+ * struct cdns3_device - represent USB device.
+ * @dev: pointer to device structure associated whit this controller
+ * @sysdev: pointer to the DMA capable device
+ * @gadget: device side representation of the peripheral controller
+ * @gadget_driver: pointer to the gadget driver
+ * @lock: for synchronizing
+ * @regs: base address for device side registers
+ * @setup_buf: used while processing usb control requests
+ * @setup_dma: dma address for setup_buf
+ * @ep0_trb: TRB used for control transfer
+ * @ep0_trb_dma: dma address of ep0_trb
+ * @zlp_buf - zlp buffer
+ * @ep0_request: dummy request used while handling USB control request
+ * @ep0_data_dir: direction for control transfer
+ * @eps: array of pointers to all endpoints with exclusion ep0
+ * @ep_nums: number of endpoints in eps
+ * @isoch_delay: value from Set Isoch Delay request. Only valid on SS/SSP.
+ * @u1_allowed: allow device transition to u1 state
+ * @u2_allowed: allow device transition to u2 state
+ * @is_selfpowered: device is self powered
+ * @setup_pending: setup packet is processing by gadget driver
+ * @hw_configured_flag: hardware endpoint configuration was set.
+ * @wake_up_flag: allow device to remote up the host
+ * @status_completion_no_call: indicate that driver is waiting for status s
+ * stage completion. It's used in deferred SET_CONFIGURATION request.
+ * @onchip_mem_allocated_size: actual size of on-chip memory assigned
+ * to endpoints
+ * @pending_status_wq: workqueue handling status stage for deferred requests.
+ * @pending_status_request: request for which status stage was deferred
+ */
+struct cdns3_device {
+ struct device *dev;
+ struct device *sysdev;
+
+ struct usb_gadget gadget;
+ struct usb_gadget_driver *gadget_driver;
+
+ /* generic spin-lock for drivers */
+ spinlock_t lock;
+
+ struct cdns3_usb_regs __iomem *regs;
+
+ struct usb_ctrlrequest *setup_buf;
+ dma_addr_t setup_dma;
+ struct cdns3_trb *ep0_trb;
+ dma_addr_t ep0_trb_dma;
+ void *zlp_buf;
+ struct usb_request *ep0_request;
+ int ep0_data_dir;
+
+ struct cdns3_endpoint *eps[CDNS3_ENDPOINTS_MAX_COUNT];
+ int ep_nums;
+
+ u32 selected_ep;
+ u16 isoch_delay;
+
+ unsigned u1_allowed:1;
+ unsigned u2_allowed:1;
+ unsigned is_selfpowered:1;
+ unsigned setup_pending:1;
+ int hw_configured_flag:1;
+ int wake_up_flag:1;
+ unsigned status_completion_no_call:1;
+
+ struct work_struct pending_status_wq;
+ struct usb_request *pending_status_request;
+
+ /*in KB */
+ int onchip_mem_allocated_size;
+};
+
+int cdns3_handshake(void __iomem *ptr, u32 mask, u32 done, int usec);
+void cdns3_set_register_bit(void __iomem *ptr, u32 mask);
+dma_addr_t cdns3_trb_virt_to_dma(struct cdns3_endpoint *priv_ep,
+ struct cdns3_trb *trb);
+enum usb_device_speed cdns3_get_speed(struct cdns3_device *priv_dev);
+void cdns3_pending_setup_status_handler(struct work_struct *work);
+void cdns3_gadget_unconfig(struct cdns3_device *priv_dev);
+void cdns3_set_hw_configuration(struct cdns3_device *priv_dev);
+void cdns3_select_ep(struct cdns3_device *priv_dev, u32 ep);
+void cdns3_allow_enable_l1(struct cdns3_device *priv_dev, int enable);
+struct usb_request *cdns3_next_request(struct list_head *list);
+int cdns3_ep_run_transfer(struct cdns3_endpoint *priv_ep,
+ struct usb_request *request);
+u8 cdns3_ep_addr_to_index(u8 ep_addr);
+int cdns3_gadget_ep_set_wedge(struct usb_ep *ep);
+int cdns3_gadget_ep_set_halt(struct usb_ep *ep, int value);
+struct usb_request *cdns3_gadget_ep_alloc_request(struct usb_ep *ep,
+ gfp_t gfp_flags);
+void cdns3_gadget_ep_free_request(struct usb_ep *ep,
+ struct usb_request *request);
+int cdns3_gadget_ep_dequeue(struct usb_ep *ep, struct usb_request *request);
+void cdns3_gadget_giveback(struct cdns3_endpoint *priv_ep,
+ struct cdns3_request *priv_req,
+ int status);
+
+int cdns3_init_ep0(struct cdns3_device *priv_dev);
+void cdns3_ep0_config(struct cdns3_device *priv_dev);
+void cdns3_ep_config(struct cdns3_endpoint *priv_ep);
+void cdns3_check_ep0_interrupt_proceed(struct cdns3_device *priv_dev, int dir);
+
+#endif /* __LINUX_CDNS3_GADGET */
diff --git a/drivers/usb/cdns3/host-export.h b/drivers/usb/cdns3/host-export.h
new file mode 100644
index 000000000000..b498a170b7e8
--- /dev/null
+++ b/drivers/usb/cdns3/host-export.h
@@ -0,0 +1,28 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Cadence USBSS DRD Driver - Host Export APIs
+ *
+ * Copyright (C) 2017-2018 NXP
+ *
+ * Authors: Peter Chen <[email protected]>
+ */
+#ifndef __LINUX_CDNS3_HOST_EXPORT
+#define __LINUX_CDNS3_HOST_EXPORT
+
+#ifdef CONFIG_USB_CDNS3_HOST
+
+int cdns3_host_init(struct cdns3 *cdns);
+void cdns3_host_exit(struct cdns3 *cdns);
+
+#else
+
+static inline int cdns3_host_init(struct cdns3 *cdns)
+{
+ return -ENXIO;
+}
+
+static inline void cdns3_host_exit(struct cdns3 *cdns) { }
+
+#endif /* CONFIG_USB_CDNS3_HOST */
+
+#endif /* __LINUX_CDNS3_HOST_EXPORT */
diff --git a/drivers/usb/cdns3/host.c b/drivers/usb/cdns3/host.c
new file mode 100644
index 000000000000..e16175e0328a
--- /dev/null
+++ b/drivers/usb/cdns3/host.c
@@ -0,0 +1,74 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Cadence USBSS DRD Driver - host side
+ *
+ * Copyright (C) 2018 Cadence Design Systems.
+ * Copyright (C) 2017-2018 NXP
+ *
+ * Authors: Peter Chen <[email protected]>
+ * Pawel Laszczak <[email protected]>
+ */
+
+#include <linux/platform_device.h>
+#include "core.h"
+
+static int __cdns3_host_init(struct cdns3 *cdns)
+{
+ struct platform_device *xhci;
+ int ret;
+
+ xhci = platform_device_alloc("xhci-hcd", PLATFORM_DEVID_AUTO);
+ if (!xhci) {
+ dev_err(cdns->dev, "couldn't allocate xHCI device\n");
+ return -ENOMEM;
+ }
+
+ xhci->dev.parent = cdns->dev;
+ cdns->host_dev = xhci;
+
+ ret = platform_device_add_resources(xhci, cdns->xhci_res,
+ CDNS3_XHCI_RESOURCES_NUM);
+ if (ret) {
+ dev_err(cdns->dev, "couldn't add resources to xHCI device\n");
+ goto err1;
+ }
+
+ ret = platform_device_add(xhci);
+ if (ret) {
+ dev_err(cdns->dev, "failed to register xHCI device\n");
+ goto err1;
+ }
+
+ return 0;
+err1:
+ platform_device_put(xhci);
+ return ret;
+}
+
+static void cdns3_host_exit(struct cdns3 *cdns)
+{
+ platform_device_unregister(cdns->host_dev);
+ cdns->host_dev = NULL;
+}
+
+int cdns3_host_init(struct cdns3 *cdns)
+{
+ struct cdns3_role_driver *rdrv;
+
+ rdrv = devm_kzalloc(cdns->dev, sizeof(*rdrv), GFP_KERNEL);
+ if (!rdrv)
+ return -ENOMEM;
+
+ rdrv->start = __cdns3_host_init;
+ rdrv->stop = cdns3_host_exit;
+ rdrv->state = CDNS3_ROLE_STATE_INACTIVE;
+#if CONFIG_PM
+ rdrv->suspend = NULL;
+ rdrv->resume = NULL;
+#endif /* CONFIG_PM */
+ rdrv->name = "host";
+
+ cdns->roles[CDNS3_ROLE_HOST] = rdrv;
+
+ return 0;
+}
diff --git a/drivers/usb/cdns3/trace.c b/drivers/usb/cdns3/trace.c
new file mode 100644
index 000000000000..587ae08e019d
--- /dev/null
+++ b/drivers/usb/cdns3/trace.c
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * USBSS device controller driver Trace Support
+ *
+ * Copyright (C) 2018 Cadence.
+ *
+ * Author: Pawel Laszczak <[email protected]>
+ */
+
+#define CREATE_TRACE_POINTS
+#include "trace.h"
diff --git a/drivers/usb/cdns3/trace.h b/drivers/usb/cdns3/trace.h
new file mode 100644
index 000000000000..a5c8b2a756b4
--- /dev/null
+++ b/drivers/usb/cdns3/trace.h
@@ -0,0 +1,343 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * USBSS device controller driver.
+ * Trace support header file.
+ *
+ * Copyright (C) 2018 Cadence.
+ *
+ * Author: Pawel Laszczak <[email protected]>
+ */
+
+#undef TRACE_SYSTEM
+#define TRACE_SYSTEM cdns3
+
+#if !defined(__LINUX_CDNS3_TRACE) || defined(TRACE_HEADER_MULTI_READ)
+#define __LINUX_CDNS3_TRACE
+
+#include <linux/types.h>
+#include <linux/tracepoint.h>
+#include <asm/byteorder.h>
+#include "core.h"
+#include "gadget.h"
+#include "debug.h"
+
+#define CDNS3_MSG_MAX 500
+
+DECLARE_EVENT_CLASS(cdns3_log_doorbell,
+ TP_PROTO(const char *ep_name),
+ TP_ARGS(ep_name),
+ TP_STRUCT__entry(
+ __field(const char *, ep_name)
+ ),
+ TP_fast_assign(
+ __entry->ep_name = ep_name;
+ ),
+ TP_printk("//Ding Dong %s", __entry->ep_name)
+);
+
+DEFINE_EVENT(cdns3_log_doorbell, cdns3_doorbell_ep0,
+ TP_PROTO(const char *ep_name),
+ TP_ARGS(ep_name)
+);
+
+DEFINE_EVENT(cdns3_log_doorbell, cdns3_doorbell_epx,
+ TP_PROTO(const char *ep_name),
+ TP_ARGS(ep_name)
+);
+
+DECLARE_EVENT_CLASS(cdns3_log_usb_irq,
+ TP_PROTO(struct cdns3_device *priv_dev, u32 usb_ists),
+ TP_ARGS(priv_dev, usb_ists),
+ TP_STRUCT__entry(
+ __field(struct cdns3_device *, priv_dev)
+ __field(u32, usb_ists)
+ ),
+ TP_fast_assign(
+ __entry->priv_dev = priv_dev;
+ __entry->usb_ists = usb_ists;
+ ),
+ TP_printk("%s", cdns3_decode_usb_irq(__entry->priv_dev,
+ __entry->usb_ists))
+);
+
+DEFINE_EVENT(cdns3_log_usb_irq, cdns3_usb_irq,
+ TP_PROTO(struct cdns3_device *priv_dev, u32 usb_ists),
+ TP_ARGS(priv_dev, usb_ists)
+);
+
+DECLARE_EVENT_CLASS(cdns3_log_epx_irq,
+ TP_PROTO(struct cdns3_endpoint *priv_ep),
+ TP_ARGS(priv_ep),
+ TP_STRUCT__entry(
+ __field(struct cdns3_endpoint *, priv_ep)
+ ),
+ TP_fast_assign(
+ __entry->priv_ep = priv_ep;
+ ),
+ TP_printk("%s", cdns3_decode_epx_irq(__entry->priv_ep))
+);
+
+DEFINE_EVENT(cdns3_log_epx_irq, cdns3_epx_irq,
+ TP_PROTO(struct cdns3_endpoint *priv_ep),
+ TP_ARGS(priv_ep)
+);
+
+DECLARE_EVENT_CLASS(cdns3_log_ep0_irq,
+ TP_PROTO(struct cdns3_device *priv_dev),
+ TP_ARGS(priv_dev),
+ TP_STRUCT__entry(
+ __field(struct cdns3_device *, priv_dev)
+ ),
+ TP_fast_assign(
+ __entry->priv_dev = priv_dev;
+ ),
+ TP_printk("%s", cdns3_decode_ep0_irq(__entry->priv_dev))
+);
+
+DEFINE_EVENT(cdns3_log_ep0_irq, cdns3_ep0_irq,
+ TP_PROTO(struct cdns3_device *priv_dev),
+ TP_ARGS(priv_dev)
+);
+
+DECLARE_EVENT_CLASS(cdns3_log_ctrl,
+ TP_PROTO(struct usb_ctrlrequest *ctrl),
+ TP_ARGS(ctrl),
+ TP_STRUCT__entry(
+ __field(u8, bRequestType)
+ __field(u8, bRequest)
+ __field(u16, wValue)
+ __field(u16, wIndex)
+ __field(u16, wLength)
+ __dynamic_array(char, str, CDNS3_MSG_MAX)
+ ),
+ TP_fast_assign(
+ __entry->bRequestType = ctrl->bRequestType;
+ __entry->bRequest = ctrl->bRequest;
+ __entry->wValue = le16_to_cpu(ctrl->wValue);
+ __entry->wIndex = le16_to_cpu(ctrl->wIndex);
+ __entry->wLength = le16_to_cpu(ctrl->wLength);
+ ),
+ TP_printk("%s", cdns3_decode_ctrl(__get_str(str), __entry->bRequestType,
+ __entry->bRequest, __entry->wValue,
+ __entry->wIndex, __entry->wLength)
+ )
+);
+
+DEFINE_EVENT(cdns3_log_ctrl, cdns3_ctrl_req,
+ TP_PROTO(struct usb_ctrlrequest *ctrl),
+ TP_ARGS(ctrl)
+);
+
+DECLARE_EVENT_CLASS(cdns3_log_request,
+ TP_PROTO(struct cdns3_request *req),
+ TP_ARGS(req),
+ TP_STRUCT__entry(
+ __string(name, req->priv_ep->name)
+ __field(struct cdns3_request *, req)
+ __field(unsigned int, actual)
+ __field(unsigned int, length)
+ __field(int, status)
+ __field(int, zero)
+ __field(int, short_not_ok)
+ __field(int, no_interrupt)
+ __field(int, start_trb)
+ __field(int, end_trb)
+ __field(struct cdns3_trb *, start_trb_addr)
+ __field(int, flags)
+ ),
+ TP_fast_assign(
+ __assign_str(name, req->priv_ep->name);
+ __entry->req = req;
+ __entry->actual = req->request.actual;
+ __entry->length = req->request.length;
+ __entry->status = req->request.status;
+ __entry->zero = req->request.zero;
+ __entry->short_not_ok = req->request.short_not_ok;
+ __entry->no_interrupt = req->request.no_interrupt;
+ __entry->start_trb = req->start_trb;
+ __entry->end_trb = req->end_trb;
+ __entry->start_trb_addr = req->trb;
+ __entry->flags = req->flags;
+ ),
+ TP_printk("%s: req: %p, length: %u/%u %s%s%s, status: %d,"
+ " trb: [start:%d, end:%d: virt addr %pa], flags:%x ",
+ __get_str(name), __entry->req, __entry->actual, __entry->length,
+ __entry->zero ? "zero | " : "",
+ __entry->short_not_ok ? "short | " : "",
+ __entry->no_interrupt ? "no int" : "",
+ __entry->status,
+ __entry->start_trb,
+ __entry->end_trb,
+ __entry->start_trb_addr,
+ __entry->flags
+ )
+);
+
+DEFINE_EVENT(cdns3_log_request, cdns3_alloc_request,
+ TP_PROTO(struct cdns3_request *req),
+ TP_ARGS(req)
+);
+
+DEFINE_EVENT(cdns3_log_request, cdns3_free_request,
+ TP_PROTO(struct cdns3_request *req),
+ TP_ARGS(req)
+);
+
+DEFINE_EVENT(cdns3_log_request, cdns3_ep_queue,
+ TP_PROTO(struct cdns3_request *req),
+ TP_ARGS(req)
+);
+
+DEFINE_EVENT(cdns3_log_request, cdns3_ep_dequeue,
+ TP_PROTO(struct cdns3_request *req),
+ TP_ARGS(req)
+);
+
+DEFINE_EVENT(cdns3_log_request, cdns3_gadget_giveback,
+ TP_PROTO(struct cdns3_request *req),
+ TP_ARGS(req)
+);
+
+DECLARE_EVENT_CLASS(cdns3_log_trb,
+ TP_PROTO(struct cdns3_endpoint *priv_ep, struct cdns3_trb *trb),
+ TP_ARGS(priv_ep, trb),
+ TP_STRUCT__entry(
+ __string(name, priv_ep->name)
+ __field(struct cdns3_trb *, trb)
+ __field(u32, buffer)
+ __field(u32, length)
+ __field(u32, control)
+ __field(u32, type)
+ ),
+ TP_fast_assign(
+ __assign_str(name, priv_ep->name);
+ __entry->trb = trb;
+ __entry->buffer = trb->buffer;
+ __entry->length = trb->length;
+ __entry->control = trb->control;
+ __entry->type = usb_endpoint_type(priv_ep->endpoint.desc);
+ ),
+ TP_printk("%s: trb 0x%pa, dma buf: 0x%08x, size: %ld, ctrl: 0x%08x (%s%s%s%s%s%s%s)",
+ __get_str(name), __entry->trb, __entry->buffer,
+ TRB_LEN(__entry->length), __entry->control,
+ __entry->control & TRB_CYCLE ? "C=1, " : "C=0, ",
+ __entry->control & TRB_TOGGLE ? "T=1, " : "T=0, ",
+ __entry->control & TRB_ISP ? "ISP, " : "",
+ __entry->control & TRB_FIFO_MODE ? "FIFO, " : "",
+ __entry->control & TRB_CHAIN ? "CHAIN, " : "",
+ __entry->control & TRB_IOC ? "IOC, " : "",
+ TRB_FIELD_TO_TYPE(__entry->control) == TRB_NORMAL ? "Normal" : "LINK"
+ )
+);
+
+DEFINE_EVENT(cdns3_log_trb, cdns3_prepare_trb,
+ TP_PROTO(struct cdns3_endpoint *priv_ep, struct cdns3_trb *trb),
+ TP_ARGS(priv_ep, trb)
+);
+
+DEFINE_EVENT(cdns3_log_trb, cdns3_complete_trb,
+ TP_PROTO(struct cdns3_endpoint *priv_ep, struct cdns3_trb *trb),
+ TP_ARGS(priv_ep, trb)
+);
+
+DECLARE_EVENT_CLASS(cdns3_log_ring,
+ TP_PROTO(struct cdns3_endpoint *priv_ep),
+ TP_ARGS(priv_ep),
+ TP_STRUCT__entry(
+ __field(struct cdns3_endpoint *, priv_ep)
+ __field(int, free_trbs)
+ __field(u8, pcs)
+ __field(u8, ccs)
+ __field(int, enqueue)
+ __field(int, dequeue)
+ __dynamic_array(u32, ring, TRB_RING_SIZE)
+ __dynamic_array(char, buffer,
+ (TRBS_PER_SEGMENT * 65) + CDNS3_MSG_MAX)
+ ),
+ TP_fast_assign(
+ __entry->priv_ep = priv_ep;
+ __entry->free_trbs = priv_ep->free_trbs;
+ __entry->pcs = priv_ep->pcs;
+ __entry->ccs = priv_ep->ccs;
+ __entry->enqueue = priv_ep->enqueue;
+ __entry->dequeue = priv_ep->dequeue;
+ memcpy(__get_dynamic_array(ring), priv_ep->trb_pool,
+ TRB_RING_SIZE);
+ ),
+
+ TP_printk("%s",
+ cdns3_dbg_ring(__entry->priv_ep, __entry->free_trbs,
+ __entry->pcs, __entry->ccs,
+ __entry->enqueue, __entry->dequeue,
+ (struct cdns3_trb *)__get_str(ring),
+ __get_str(buffer)))
+);
+
+DEFINE_EVENT(cdns3_log_ring, cdns3_ring,
+ TP_PROTO(struct cdns3_endpoint *priv_ep),
+ TP_ARGS(priv_ep)
+);
+
+DECLARE_EVENT_CLASS(cdns3_log_ep,
+ TP_PROTO(struct cdns3_endpoint *priv_ep),
+ TP_ARGS(priv_ep),
+ TP_STRUCT__entry(
+ __string(name, priv_ep->name)
+ __field(unsigned int, maxpacket)
+ __field(unsigned int, maxpacket_limit)
+ __field(unsigned int, max_streams)
+ __field(unsigned int, maxburst)
+ __field(unsigned int, flags)
+ __field(unsigned int, dir)
+ __field(u8, enqueue)
+ __field(u8, dequeue)
+ ),
+ TP_fast_assign(
+ __assign_str(name, priv_ep->name);
+ __entry->maxpacket = priv_ep->endpoint.maxpacket;
+ __entry->maxpacket_limit = priv_ep->endpoint.maxpacket_limit;
+ __entry->max_streams = priv_ep->endpoint.max_streams;
+ __entry->maxburst = priv_ep->endpoint.maxburst;
+ __entry->flags = priv_ep->flags;
+ __entry->dir = priv_ep->dir;
+ __entry->enqueue = priv_ep->enqueue;
+ __entry->dequeue = priv_ep->dequeue;
+ ),
+ TP_printk("%s: mps: %d/%d. streams: %d, burst: %d, enq idx: %d, "
+ "deq idx: %d, flags %s%s%s%s%s%s%s%s, dir: %s",
+ __get_str(name), __entry->maxpacket,
+ __entry->maxpacket_limit, __entry->max_streams,
+ __entry->maxburst, __entry->enqueue,
+ __entry->dequeue,
+ __entry->flags & EP_ENABLED ? "EN | " : "",
+ __entry->flags & EP_STALL ? "STALL | " : "",
+ __entry->flags & EP_WEDGE ? "WEDGE | " : "",
+ __entry->flags & EP_TRANSFER_STARTED ? "STARTED | " : "",
+ __entry->flags & EP_UPDATE_EP_TRBADDR ? "UPD TRB | " : "",
+ __entry->flags & EP_PENDING_REQUEST ? "REQ PEN | " : "",
+ __entry->flags & EP_RING_FULL ? "RING FULL |" : "",
+ __entry->flags & EP_CLAIMED ? "CLAIMED " : "",
+ __entry->dir ? "IN" : "OUT"
+ )
+);
+
+DEFINE_EVENT(cdns3_log_ep, cdns3_gadget_ep_enable,
+ TP_PROTO(struct cdns3_endpoint *priv_ep),
+ TP_ARGS(priv_ep)
+);
+
+DEFINE_EVENT(cdns3_log_ep, cdns3_gadget_ep_disable,
+ TP_PROTO(struct cdns3_endpoint *priv_ep),
+ TP_ARGS(priv_ep)
+);
+#endif /* __LINUX_CDNS3_TRACE */
+
+/* this part must be outside header guard */
+
+#undef TRACE_INCLUDE_PATH
+#define TRACE_INCLUDE_PATH .
+
+#undef TRACE_INCLUDE_FILE
+#define TRACE_INCLUDE_FILE trace
+
+#include <trace/define_trace.h>
--
2.17.1

2018-12-11 09:41:26

by Roger Quadros

[permalink] [raw]

Subject: Re: [PATCH v1 2/2] usb:cdns3 Add Cadence USB3 DRD Driver

Pawel,

On 10/12/18 14:39, Pawel Laszczak wrote:
> This patch introduce new Cadence USBSS DRD driver
> to linux kernel.
>
> The Cadence USBSS DRD Driver is a highly
> configurable IP Core which can be
> instantiated as Dual-Role Device (DRD),
> Peripheral Only and Host Only (XHCI)
> configurations.
>
> The current driver has been validated with
> FPGA burned. We have support for PCIe
> bus, which is used on FPGA prototyping.
>
> The host side of USBSS-DRD controller is compliance
> with XHCI specification, so it works with
> standard XHCI linux driver.
>
> Signed-off-by: Pawel Laszczak <[email protected]>
> ---
> drivers/usb/Kconfig | 2 +
> drivers/usb/Makefile | 2 +
> drivers/usb/cdns3/Kconfig | 44 +
> drivers/usb/cdns3/Makefile | 16 +
> drivers/usb/cdns3/cdns3-pci-wrap.c | 157 +++
> drivers/usb/cdns3/core.c | 451 +++++++
> drivers/usb/cdns3/core.h | 108 ++
> drivers/usb/cdns3/debug.h | 346 ++++++
> drivers/usb/cdns3/debugfs.c | 168 +++
> drivers/usb/cdns3/drd.c | 315 +++++
> drivers/usb/cdns3/drd.h | 129 ++
> drivers/usb/cdns3/ep0.c | 864 +++++++++++++
> drivers/usb/cdns3/gadget-export.h | 28 +
> drivers/usb/cdns3/gadget.c | 1802 ++++++++++++++++++++++++++++
> drivers/usb/cdns3/gadget.h | 1177 ++++++++++++++++++
> drivers/usb/cdns3/host-export.h | 28 +
> drivers/usb/cdns3/host.c | 74 ++
> drivers/usb/cdns3/trace.c | 11 +
> drivers/usb/cdns3/trace.h | 343 ++++++

You went to the other extreme of combining everything (host/gadget/drd) together
which again makes this very hard to review.

I think what Felipe meant was to only combine the gadget driver code into one patch.

The series could be split into 6 patches like so.
-dt binding
-pci glue
-core driver
-host driver
-gadget driver
-drd driver

> 19 files changed, 6065 insertions(+)
> create mode 100644 drivers/usb/cdns3/Kconfig
> create mode 100644 drivers/usb/cdns3/Makefile
> create mode 100644 drivers/usb/cdns3/cdns3-pci-wrap.c
> create mode 100644 drivers/usb/cdns3/core.c
> create mode 100644 drivers/usb/cdns3/core.h
> create mode 100644 drivers/usb/cdns3/debug.h
> create mode 100644 drivers/usb/cdns3/debugfs.c
> create mode 100644 drivers/usb/cdns3/drd.c
> create mode 100644 drivers/usb/cdns3/drd.h
> create mode 100644 drivers/usb/cdns3/ep0.c
> create mode 100644 drivers/usb/cdns3/gadget-export.h
> create mode 100644 drivers/usb/cdns3/gadget.c
> create mode 100644 drivers/usb/cdns3/gadget.h
> create mode 100644 drivers/usb/cdns3/host-export.h
> create mode 100644 drivers/usb/cdns3/host.c
> create mode 100644 drivers/usb/cdns3/trace.c
> create mode 100644 drivers/usb/cdns3/trace.h
>
<snip>

cheers,
-roger

--
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki

2018-12-11 10:02:42

[permalink] [raw]

Subject: RE: [PATCH v1 2/2] usb:cdns3 Add Cadence USB3 DRD Driver

Hi,

>On 10/12/18 14:39, Pawel Laszczak wrote:
>> This patch introduce new Cadence USBSS DRD driver
>> to linux kernel.
>>
>> The Cadence USBSS DRD Driver is a highly
>> configurable IP Core which can be
>> instantiated as Dual-Role Device (DRD),
>> Peripheral Only and Host Only (XHCI)
>> configurations.
>>
>> The current driver has been validated with
>> FPGA burned. We have support for PCIe
>> bus, which is used on FPGA prototyping.
>>
>> The host side of USBSS-DRD controller is compliance
>> with XHCI specification, so it works with
>> standard XHCI linux driver.
>>
>> Signed-off-by: Pawel Laszczak <[email protected]>
>> ---
>> drivers/usb/Kconfig | 2 +
>> drivers/usb/Makefile | 2 +
>> drivers/usb/cdns3/Kconfig | 44 +
>> drivers/usb/cdns3/Makefile | 16 +
>> drivers/usb/cdns3/cdns3-pci-wrap.c | 157 +++
>> drivers/usb/cdns3/core.c | 451 +++++++
>> drivers/usb/cdns3/core.h | 108 ++
>> drivers/usb/cdns3/debug.h | 346 ++++++
>> drivers/usb/cdns3/debugfs.c | 168 +++
>> drivers/usb/cdns3/drd.c | 315 +++++
>> drivers/usb/cdns3/drd.h | 129 ++
>> drivers/usb/cdns3/ep0.c | 864 +++++++++++++
>> drivers/usb/cdns3/gadget-export.h | 28 +
>> drivers/usb/cdns3/gadget.c | 1802 ++++++++++++++++++++++++++++
>> drivers/usb/cdns3/gadget.h | 1177 ++++++++++++++++++
>> drivers/usb/cdns3/host-export.h | 28 +
>> drivers/usb/cdns3/host.c | 74 ++
>> drivers/usb/cdns3/trace.c | 11 +
>> drivers/usb/cdns3/trace.h | 343 ++++++
>
>You went to the other extreme of combining everything (host/gadget/drd) together
>which again makes this very hard to review.
>
>I think what Felipe meant was to only combine the gadget driver code into one patch.
>
>The series could be split into 6 patches like so.
>-dt binding
>-pci glue
>-core driver
>-host driver
>-gadget driver
>-drd driver

Felipe wrote:
"
Frankly, I don't understand why this is a series. It's a single driver
and splitting it into a series just makes it more difficult to review,
actually.

Sure, a single patch will be large, but there's no way to have a
functional driver until all patches are applied, anyway.
"

Felipe should I split this driver as suggested by Roger ?.
Now it's very big patch but it's still a single driver.

>> 19 files changed, 6065 insertions(+)
>> create mode 100644 drivers/usb/cdns3/Kconfig
>> create mode 100644 drivers/usb/cdns3/Makefile
>> create mode 100644 drivers/usb/cdns3/cdns3-pci-wrap.c
>> create mode 100644 drivers/usb/cdns3/core.c
>> create mode 100644 drivers/usb/cdns3/core.h
>> create mode 100644 drivers/usb/cdns3/debug.h
>> create mode 100644 drivers/usb/cdns3/debugfs.c
>> create mode 100644 drivers/usb/cdns3/drd.c
>> create mode 100644 drivers/usb/cdns3/drd.h
>> create mode 100644 drivers/usb/cdns3/ep0.c
>> create mode 100644 drivers/usb/cdns3/gadget-export.h
>> create mode 100644 drivers/usb/cdns3/gadget.c
>> create mode 100644 drivers/usb/cdns3/gadget.h
>> create mode 100644 drivers/usb/cdns3/host-export.h
>> create mode 100644 drivers/usb/cdns3/host.c
>> create mode 100644 drivers/usb/cdns3/trace.c
>> create mode 100644 drivers/usb/cdns3/trace.h
>>
><snip>
>
Cheers
Pawel

2018-12-11 10:19:44

by Roger Quadros

[permalink] [raw]

Subject: Re: [PATCH v1 1/2] dt-bindings: add binding for USBSS-DRD controller.

Pawel,

On 10/12/18 14:39, Pawel Laszczak wrote:
> This patch aim at documenting USB related dt-bindings for the
> Cadence USBSS-DRD controller.
>
> Signed-off-by: Pawel Laszczak <[email protected]>
> ---
> .../devicetree/bindings/usb/cdns3-usb.txt | 31 +++++++++++++++++++
> 1 file changed, 31 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/usb/cdns3-usb.txt
>
> diff --git a/Documentation/devicetree/bindings/usb/cdns3-usb.txt b/Documentation/devicetree/bindings/usb/cdns3-usb.txt
> new file mode 100644
> index 000000000000..ae4a255f0b10
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/usb/cdns3-usb.txt
> @@ -0,0 +1,31 @@
> +Binding for the Cadence USBSS-DRD controller
> +
> +Required properties:
> + - reg: Physical base address and size of the controller's register areas.
> + Controller has 3 different regions:
> + region 1 - HOST registers area
> + region 2 - DEVICE registers area
> + region 3 - OTG/DRD registers area
> + - compatible: Should contain: "cdns,usb3"
> + - interrupts: Interrupt specifier. Refer to interrupt bindings.
> + Driver supports only single interrupt line.
> + This single interrupt is shared between Device,
> + host and OTG/DRD part of driver.
> +
> +Optional propertiesi:

s/propertiesi/properties

> + - maximum-speed : valid arguments are "super-speed", "high-speed" and
> + "full-speed"; refer to usb/generic.txt
> + - dr_mode: Should be one of "host", "peripheral" or "otg".
> + - phys: reference to the USB PHY
> + - phy-names: name of the USB PHY, should be "cdns3,usbphy"
> +
> +
> +Example:
> + usb@f3000000 {
> + compatible = "cdns,usb3";
> + interrupts = <USB_IRQ 7 IRQ_TYPE_LEVEL_HIGH>;
> + reg = <0xf3000000 0x10000 //memory area for HOST registers
> + 0xf3010000 0x10000 //memory area for DEVICE registers
> + 0xf3020000 0x10000>; //memory area for OTG/DRD registers

Use "/* <comment> */" instead.

> + };
> +
>

cheers,
-roger
--
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki

2018-12-11 11:48:29

[permalink] [raw]

Subject: Re: [PATCH v1 2/2] usb:cdns3 Add Cadence USB3 DRD Driver

Hi,

Roger Quadros <[email protected]> writes:
>> This patch introduce new Cadence USBSS DRD driver
>> to linux kernel.
>>
>> The Cadence USBSS DRD Driver is a highly
>> configurable IP Core which can be
>> instantiated as Dual-Role Device (DRD),
>> Peripheral Only and Host Only (XHCI)
>> configurations.
>>
>> The current driver has been validated with
>> FPGA burned. We have support for PCIe
>> bus, which is used on FPGA prototyping.
>>
>> The host side of USBSS-DRD controller is compliance
>> with XHCI specification, so it works with
>> standard XHCI linux driver.
>>
>> Signed-off-by: Pawel Laszczak <[email protected]>
>> ---
>> drivers/usb/Kconfig | 2 +
>> drivers/usb/Makefile | 2 +
>> drivers/usb/cdns3/Kconfig | 44 +
>> drivers/usb/cdns3/Makefile | 16 +
>> drivers/usb/cdns3/cdns3-pci-wrap.c | 157 +++
>> drivers/usb/cdns3/core.c | 451 +++++++
>> drivers/usb/cdns3/core.h | 108 ++
>> drivers/usb/cdns3/debug.h | 346 ++++++
>> drivers/usb/cdns3/debugfs.c | 168 +++
>> drivers/usb/cdns3/drd.c | 315 +++++
>> drivers/usb/cdns3/drd.h | 129 ++
>> drivers/usb/cdns3/ep0.c | 864 +++++++++++++
>> drivers/usb/cdns3/gadget-export.h | 28 +
>> drivers/usb/cdns3/gadget.c | 1802 ++++++++++++++++++++++++++++
>> drivers/usb/cdns3/gadget.h | 1177 ++++++++++++++++++
>> drivers/usb/cdns3/host-export.h | 28 +
>> drivers/usb/cdns3/host.c | 74 ++
>> drivers/usb/cdns3/trace.c | 11 +
>> drivers/usb/cdns3/trace.h | 343 ++++++
>
> You went to the other extreme of combining everything (host/gadget/drd) together
> which again makes this very hard to review.
>
> I think what Felipe meant was to only combine the gadget driver code
> into one patch.
>
> The series could be split into 6 patches like so.
> -dt binding
> -pci glue
> -core driver
> -host driver
> -gadget driver
> -drd driver

no, no. This is fine. We _could_ split out PCI glue to its own patch,
but it's rather pointless seing as it's so small.

--
balbi

Attachments:

signature.asc (847.00 B)

2018-12-11 12:16:42

[permalink] [raw]

Subject: Re: [PATCH v1 2/2] usb:cdns3 Add Cadence USB3 DRD Driver

Hi,

Pawel Laszczak <[email protected]> writes:
> +static int cdns3_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct resource *res;
> + struct cdns3 *cdns;
> + void __iomem *regs;
> + int ret;
> +
> + cdns = devm_kzalloc(dev, sizeof(*cdns), GFP_KERNEL);
> + if (!cdns)
> + return -ENOMEM;
> +
> + cdns->dev = dev;
> +
> + platform_set_drvdata(pdev, cdns);
> +
> + res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
> + if (!res) {
> + dev_err(dev, "missing IRQ\n");
> + return -ENODEV;
> + }
> + cdns->irq = res->start;
> +
> + cdns->xhci_res[0] = *res;
> +
> + /*
> + * Request memory region
> + * region-0: xHCI
> + * region-1: Peripheral
> + * region-2: OTG registers
> + */
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + cdns->xhci_res[1] = *res;
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
> + regs = devm_ioremap_resource(dev, res);
> + if (IS_ERR(regs))
> + return PTR_ERR(regs);
> + cdns->dev_regs = regs;
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
> + regs = devm_ioremap_resource(dev, res);
> + if (IS_ERR(regs))
> + return PTR_ERR(regs);
> + cdns->otg_regs = regs;
> +
> + mutex_init(&cdns->mutex);
> +
> + cdns->phy = devm_phy_get(dev, "cdns3,usbphy");
> + if (IS_ERR(cdns->phy)) {
> + ret = PTR_ERR(cdns->phy);
> + if (ret == -ENOSYS || ret == -ENODEV) {

Are you sure you can get ENOSYS here? Have you checked output of
checkpatch --strict?

-:852: WARNING: ENOSYS means 'invalid syscall nr' and nothing else

> +#ifdef CONFIG_PM_SLEEP
> +static int cdns3_suspend(struct device *dev)
> +{
> + /* TODO: Implements this function. */
> + return 0;
> +}
> +
> +static int cdns3_resume(struct device *dev)
> +{
> + /* TODO: Implements this function. */
> + return 0;
> +}
> +#endif /* CONFIG_PM_SLEEP */
> +static int cdns3_runtime_suspend(struct device *dev)
> +{ /* TODO: Implements this function. */
> + return 0;
> +}
> +
> +static int cdns3_runtime_resume(struct device *dev)
> +{
> + /* TODO: Implements this function. */
> + return 0;
> +}
> +#endif /* CONFIG_PM */

please no TODO stubs. Just get rid of your dev_pm_ops if you don't
implement them. Come up with a later patch adding a proper
implementation for PM.

> +static int __init cdns3_driver_platform_register(void)
> +{
> + return platform_driver_register(&cdns3_driver);
> +}
> +module_init(cdns3_driver_platform_register);
> +
> +static void __exit cdns3_driver_platform_unregister(void)
> +{
> + platform_driver_unregister(&cdns3_driver);
> +}
> +module_exit(cdns3_driver_platform_unregister);

module_platform_driver()

> diff --git a/drivers/usb/cdns3/debug.h b/drivers/usb/cdns3/debug.h
> new file mode 100644
> index 000000000000..afb81d224718
> --- /dev/null
> +++ b/drivers/usb/cdns3/debug.h
> @@ -0,0 +1,346 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * Cadence USBSS DRD Driver.
> + * Debug header file.
> + *
> + * Copyright (C) 2018 Cadence.
> + *
> + * Author: Pawel Laszczak <[email protected]>
> + */
> +#ifndef __LINUX_CDNS3_DEBUG
> +#define __LINUX_CDNS3_DEBUG
> +#include "gadget.h"
> +
> +static inline void cdns3_decode_get_status(u8 bRequestType, u16 wIndex,
> + u16 wLength, char *str)
> +{
> + switch (bRequestType & USB_RECIP_MASK) {
> + case USB_RECIP_INTERFACE:
> + sprintf(str, "Get Interface Status Intf = %d, L: = %d",
> + wIndex, wLength);
> + break;
> + case USB_RECIP_ENDPOINT:
> + sprintf(str, "Get Endpoint Status ep%d%s",
> + wIndex & ~USB_DIR_IN,
> + wIndex & USB_DIR_IN ? "in" : "out");
> + break;
> + }
> +}
> +
> +static inline const char *cdns3_decode_device_feature(u16 wValue)
> +{
> + switch (wValue) {
> + case USB_DEVICE_SELF_POWERED:
> + return "Self Powered";
> + case USB_DEVICE_REMOTE_WAKEUP:
> + return "Remote Wakeup";
> + case USB_DEVICE_TEST_MODE:
> + return "Test Mode";
> + case USB_DEVICE_U1_ENABLE:
> + return "U1 Enable";
> + case USB_DEVICE_U2_ENABLE:
> + return "U2 Enable";
> + case USB_DEVICE_LTM_ENABLE:
> + return "LTM Enable";
> + default:
> + return "UNKNOWN";
> + }
> +}
> +
> +static inline const char *cdns3_decode_test_mode(u16 wIndex)
> +{
> + switch (wIndex) {
> + case TEST_J:
> + return ": TEST_J";
> + case TEST_K:
> + return ": TEST_K";
> + case TEST_SE0_NAK:
> + return ": TEST_SE0_NAK";
> + case TEST_PACKET:
> + return ": TEST_PACKET";
> + case TEST_FORCE_EN:
> + return ": TEST_FORCE_EN";
> + default:
> + return ": UNKNOWN";
> + }
> +}
> +
> +static inline void cdns3_decode_set_clear_feature(u8 bRequestType, u8 bRequest,
> + u16 wValue, u16 wIndex,
> + char *str)
> +{
> + switch (bRequestType & USB_RECIP_MASK) {
> + case USB_RECIP_DEVICE:
> + sprintf(str, "%s Device Feature(%s%s)",
> + bRequest == USB_REQ_CLEAR_FEATURE ? "Clear" : "Set",
> + cdns3_decode_device_feature(wValue),
> + wValue == USB_DEVICE_TEST_MODE ?
> + cdns3_decode_test_mode(wIndex) : "");
> + break;
> + case USB_RECIP_INTERFACE:
> + sprintf(str, "%s Interface Feature(%s)",
> + bRequest == USB_REQ_CLEAR_FEATURE ? "Clear" : "Set",
> + wIndex == USB_INTRF_FUNC_SUSPEND ?
> + "Function Suspend" : "UNKNOWN");
> + break;
> + case USB_RECIP_ENDPOINT:
> + sprintf(str, "%s Endpoint Feature(%s ep%d%s)",
> + bRequest == USB_REQ_CLEAR_FEATURE ? "Clear" : "Set",
> + wIndex == USB_ENDPOINT_HALT ? "Halt" : "UNKNOWN",
> + wIndex & ~USB_DIR_IN,
> + wIndex & USB_DIR_IN ? "in" : "out");
> + break;
> + }
> +}
> +
> +static inline const char *cdns3_decode_descriptor(u16 wValue)
> +{
> + switch (wValue >> 8) {
> + case USB_DT_DEVICE:
> + return "Device";
> + case USB_DT_CONFIG:
> + return "Configuration";
> + case USB_DT_STRING:
> + return "String";
> + case USB_DT_INTERFACE:
> + return "Interface";
> + case USB_DT_ENDPOINT:
> + return "Endpoint";
> + case USB_DT_DEVICE_QUALIFIER:
> + return "Device Qualifier";
> + case USB_DT_OTHER_SPEED_CONFIG:
> + return "Other Speed Config";
> + case USB_DT_INTERFACE_POWER:
> + return "Interface Power";
> + case USB_DT_OTG:
> + return "OTG";
> + case USB_DT_DEBUG:
> + return "Debug";
> + case USB_DT_INTERFACE_ASSOCIATION:
> + return "Interface Association";
> + case USB_DT_BOS:
> + return "BOS";
> + case USB_DT_DEVICE_CAPABILITY:
> + return "Device Capability";
> + case USB_DT_SS_ENDPOINT_COMP:
> + return "SS Endpoint Companion";
> + case USB_DT_SSP_ISOC_ENDPOINT_COMP:
> + return "SSP Isochronous Endpoint Companion";
> + default:
> + return "UNKNOWN";
> + }
> +}
> +
> +/**
> + * cdns3_decode_ctrl - returns a string represetion of ctrl request
> + */
> +static inline const char *cdns3_decode_ctrl(char *str, u8 bRequestType,
> + u8 bRequest, u16 wValue,
> + u16 wIndex, u16 wLength)
> +{
> + switch (bRequest) {
> + case USB_REQ_GET_STATUS:
> + cdns3_decode_get_status(bRequestType, wIndex,
> + wLength, str);
> + break;
> + case USB_REQ_CLEAR_FEATURE:
> + case USB_REQ_SET_FEATURE:
> + cdns3_decode_set_clear_feature(bRequestType, bRequest,
> + wValue, wIndex, str);
> + break;
> + case USB_REQ_SET_ADDRESS:
> + sprintf(str, "Set Address Addr: %02x", wValue);
> + break;
> + case USB_REQ_GET_DESCRIPTOR:
> + sprintf(str, "GET %s Descriptor I: %d, L: %d",
> + cdns3_decode_descriptor(wValue),
> + wValue & 0xff, wLength);
> + break;
> + case USB_REQ_SET_DESCRIPTOR:
> + sprintf(str, "SET %s Descriptor I: %d, L: %d",
> + cdns3_decode_descriptor(wValue),
> + wValue & 0xff, wLength);
> + break;
> + case USB_REQ_GET_CONFIGURATION:
> + sprintf(str, "Get Configuration L: %d", wLength);
> + break;
> + case USB_REQ_SET_CONFIGURATION:
> + sprintf(str, "Set Configuration Config: %d ", wValue);
> + break;
> + case USB_REQ_GET_INTERFACE:
> + sprintf(str, "Get Interface Intf: %d, L: %d", wIndex, wLength);
> + break;
> + case USB_REQ_SET_INTERFACE:
> + sprintf(str, "Set Interface Intf: %d, Alt: %d", wIndex, wValue);
> + break;
> + case USB_REQ_SYNCH_FRAME:
> + sprintf(str, "Synch Frame Ep: %d, L: %d", wIndex, wLength);
> + break;
> + case USB_REQ_SET_SEL:
> + sprintf(str, "Set SEL L: %d", wLength);
> + break;
> + case USB_REQ_SET_ISOCH_DELAY:
> + sprintf(str, "Set Isochronous Delay Delay: %d ns", wValue);
> + break;
> + default:
> + sprintf(str,
> + "SETUP BRT: %02x BR: %02x V: %04x I: %04x L: %04x\n",
> + bRequestType, bRequest,
> + wValue, wIndex, wLength);
> + }
> +
> + return str;
> +}

All of these are a flat out copy of dwc3's implementation. It's much,
much better to turn dwc3's implementation into a generic, reusable
library function then spinning your own as a duplicated effort.

> diff --git a/drivers/usb/cdns3/ep0.c b/drivers/usb/cdns3/ep0.c
> new file mode 100644
> index 000000000000..1ef0e9f73e3e
> --- /dev/null
> +++ b/drivers/usb/cdns3/ep0.c
> @@ -0,0 +1,864 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Cadence USBSS DRD Driver - gadget side.
> + *
> + * Copyright (C) 2018 Cadence Design Systems.
> + * Copyright (C) 2017-2018 NXP
> + *
> + * Authors: Pawel Jez <[email protected]>,
> + * Pawel Laszczak <[email protected]>
> + * Peter Chen <[email protected]>
> + */
> +
> +#include <linux/usb/composite.h>
> +
> +#include "gadget.h"
> +#include "trace.h"
> +
> +static struct usb_endpoint_descriptor cdns3_gadget_ep0_desc = {
> + .bLength = USB_DT_ENDPOINT_SIZE,
> + .bDescriptorType = USB_DT_ENDPOINT,
> + .bmAttributes = USB_ENDPOINT_XFER_CONTROL,
> +};
> +
> +/**
> + * cdns3_ep0_run_transfer - Do transfer on default endpoint hardware
> + * @priv_dev: extended gadget object
> + * @dma_addr: physical address where data is/will be stored
> + * @length: data length
> + * @erdy: set it to 1 when ERDY packet should be sent -
> + * exit from flow control state
> + */
> +static void cdns3_ep0_run_transfer(struct cdns3_device *priv_dev,
> + dma_addr_t dma_addr,
> + unsigned int length, int erdy)
> +{
> + struct cdns3_usb_regs __iomem *regs = priv_dev->regs;
> + struct cdns3_endpoint *priv_ep = ep_to_cdns3_ep(priv_dev->gadget.ep0);
> +
> + priv_dev->ep0_trb->buffer = TRB_BUFFER(dma_addr);
> + priv_dev->ep0_trb->length = TRB_LEN(length);
> + priv_dev->ep0_trb->control = TRB_CYCLE | TRB_IOC | TRB_TYPE(TRB_NORMAL);
> +
> + trace_cdns3_prepare_trb(priv_ep, priv_dev->ep0_trb);
> +
> + cdns3_select_ep(priv_dev, priv_dev->ep0_data_dir);
> +
> + writel(EP_STS_TRBERR, &regs->ep_sts);
> + writel(EP_TRADDR_TRADDR(priv_dev->ep0_trb_dma), &regs->ep_traddr);
> + trace_cdns3_doorbell_ep0(priv_dev->ep0_data_dir ? "ep0in" : "ep0out");
> +
> + /* TRB should be prepared before starting transfer */
> + writel(EP_CMD_DRDY, &regs->ep_cmd);
> +
> + if (erdy)
> + writel(EP_CMD_ERDY, &priv_dev->regs->ep_cmd);
> +}
> +
> +/**
> + * cdns3_ep0_delegate_req - Returns status of handling setup packet
> + * Setup is handled by gadget driver
> + * @priv_dev: extended gadget object
> + * @ctrl_req: pointer to received setup packet
> + *
> + * Returns zero on success or negative value on failure
> + */
> +static int cdns3_ep0_delegate_req(struct cdns3_device *priv_dev,
> + struct usb_ctrlrequest *ctrl_req)
> +{
> + int ret;
> +
> + spin_unlock(&priv_dev->lock);
> + priv_dev->setup_pending = 1;
> + ret = priv_dev->gadget_driver->setup(&priv_dev->gadget, ctrl_req);
> + priv_dev->setup_pending = 0;
> + spin_lock(&priv_dev->lock);
> + return ret;
> +}
> +
> +static void cdns3_prepare_setup_packet(struct cdns3_device *priv_dev)
> +{
> + priv_dev->ep0_data_dir = 0;
> + cdns3_ep0_run_transfer(priv_dev, priv_dev->setup_dma,
> + sizeof(struct usb_ctrlrequest), 0);
> +}
> +
> +/**
> + * cdns3_req_ep0_set_configuration - Handling of SET_CONFIG standard USB request
> + * @priv_dev: extended gadget object
> + * @ctrl_req: pointer to received setup packet
> + *
> + * Returns 0 if success, USB_GADGET_DELAYED_STATUS on deferred status stage,
> + * error code on error
> + */
> +static int cdns3_req_ep0_set_configuration(struct cdns3_device *priv_dev,
> + struct usb_ctrlrequest *ctrl_req)
> +{
> + enum usb_device_state device_state = priv_dev->gadget.state;
> + struct cdns3_endpoint *priv_ep;
> + u32 config = le16_to_cpu(ctrl_req->wValue);
> + int result = 0;
> + int i;
> +
> + switch (device_state) {
> + case USB_STATE_ADDRESS:
> + /* Configure non-control EPs */
> + for (i = 0; i < CDNS3_ENDPOINTS_MAX_COUNT; i++) {
> + priv_ep = priv_dev->eps[i];
> + if (!priv_ep)
> + continue;
> +
> + if (priv_ep->flags & EP_CLAIMED)
> + cdns3_ep_config(priv_ep);
> + }
> +
> + result = cdns3_ep0_delegate_req(priv_dev, ctrl_req);
> +
> + if (result)
> + return result;
> +
> + if (config) {
> + cdns3_set_hw_configuration(priv_dev);
> + } else {
> + cdns3_gadget_unconfig(priv_dev);
> + usb_gadget_set_state(&priv_dev->gadget,
> + USB_STATE_ADDRESS);

this is wrong. If address is zero, state should be default, not
addressed. Addressed would be used on the other branch here, when you
have a non-zero address

> + }
> + break;
> + case USB_STATE_CONFIGURED:

where do you set this state?

> +static int cdns3_ep0_feature_handle_device(struct cdns3_device *priv_dev,
> + struct usb_ctrlrequest *ctrl,
> + int set)
> +{
> + enum usb_device_state state;
> + enum usb_device_speed speed;
> + int ret = 0;
> + u32 wValue;
> + u32 wIndex;
> + u16 tmode;
> +
> + wValue = le16_to_cpu(ctrl->wValue);
> + wIndex = le16_to_cpu(ctrl->wIndex);
> + state = priv_dev->gadget.state;
> + speed = priv_dev->gadget.speed;
> +
> + switch (ctrl->wValue) {
> + case USB_DEVICE_REMOTE_WAKEUP:
> + priv_dev->wake_up_flag = !!set;
> + break;
> + case USB_DEVICE_U1_ENABLE:
> + if (state != USB_STATE_CONFIGURED || speed != USB_SPEED_SUPER)
> + return -EINVAL;
> +
> + priv_dev->u1_allowed = !!set;
> + break;
> + case USB_DEVICE_U2_ENABLE:
> + if (state != USB_STATE_CONFIGURED || speed != USB_SPEED_SUPER)
> + return -EINVAL;
> +
> + priv_dev->u2_allowed = !!set;
> + break;
> + case USB_DEVICE_LTM_ENABLE:
> + ret = -EINVAL;
> + break;
> + case USB_DEVICE_TEST_MODE:
> + if (state != USB_STATE_CONFIGURED || speed > USB_SPEED_HIGH)
> + return -EINVAL;
> +
> + tmode = le16_to_cpu(ctrl->wIndex);
> +
> + if (!set || (tmode & 0xff) != 0)
> + return -EINVAL;
> +
> + switch (tmode >> 8) {
> + case TEST_J:
> + case TEST_K:
> + case TEST_SE0_NAK:
> + case TEST_PACKET:
> + cdns3_set_register_bit(&priv_dev->regs->usb_cmd,
> + USB_CMD_STMODE |
> + USB_STS_TMODE_SEL(tmode - 1));

I'm 90% sure this won't work. There's a reason why we only enter the
requested test mode from status stage. How have you tested this?

> diff --git a/drivers/usb/cdns3/gadget.c b/drivers/usb/cdns3/gadget.c
> new file mode 100644
> index 000000000000..a021eaf07aee
> --- /dev/null
> +++ b/drivers/usb/cdns3/gadget.c

<snip>

> +struct usb_request *cdns3_next_request(struct list_head *list)
> +{
> + if (list_empty(list))
> + return NULL;
> + return list_first_entry(list, struct usb_request, list);

list_first_entry_or_null()

> +void cdns3_gadget_unconfig(struct cdns3_device *priv_dev)
> +{
> + /* RESET CONFIGURATION */
> + writel(USB_CONF_CFGRST, &priv_dev->regs->usb_conf);
> +
> + cdns3_allow_enable_l1(priv_dev, 0);
> + priv_dev->hw_configured_flag = 0;
> + priv_dev->onchip_mem_allocated_size = 0;

clear all test modes? Reset ep0 max_packet_size to 512?

> +static irqreturn_t cdns3_device_irq_handler(int irq, void *data)
> +{
> + struct cdns3_device *priv_dev;
> + struct cdns3 *cdns = data;
> + irqreturn_t ret = IRQ_NONE;
> + unsigned long flags;
> + u32 reg;
> +
> + priv_dev = cdns->gadget_dev;
> + spin_lock_irqsave(&priv_dev->lock, flags);

you're already running in hardirq context. Why do you need this lock at
all? I would be better to use the hardirq handler to mask your
interrupts, so they don't fire again, then used the top-half (softirq)
handler to actually handle the interrupts.

> + /* check USB device interrupt */
> + reg = readl(&priv_dev->regs->usb_ists);
> + writel(reg, &priv_dev->regs->usb_ists);
> +
> + if (reg) {
> + dev_dbg(priv_dev->dev, "IRQ: usb_ists: %08X\n", reg);

I strongly advise against using dev_dbg() for debugging. Even more so
inside your IRQ handler.

> + cdns3_check_usb_interrupt_proceed(priv_dev, reg);
> + ret = IRQ_HANDLED;
> + }
> +
> + /* check endpoint interrupt */
> + reg = readl(&priv_dev->regs->ep_ists);
> +
> + /* handle default endpoint OUT */
> + if (reg & EP_ISTS_EP_OUT0) {
> + cdns3_check_ep0_interrupt_proceed(priv_dev, USB_DIR_OUT);
> + ret = IRQ_HANDLED;
> + }
> +
> + /* handle default endpoint IN */
> + if (reg & EP_ISTS_EP_IN0) {
> + cdns3_check_ep0_interrupt_proceed(priv_dev, USB_DIR_IN);
> + ret = IRQ_HANDLED;
> + }
> +
> + /* check if interrupt from non default endpoint, if no exit */
> + reg &= ~(EP_ISTS_EP_OUT0 | EP_ISTS_EP_IN0);
> + if (!reg)
> + goto irqend;
> +
> + do {
> + unsigned int bit_pos = ffs(reg);
> + u32 bit_mask = 1 << (bit_pos - 1);
> + int index;
> +
> + index = cdns3_ep_reg_pos_to_index(bit_pos);
> + cdns3_check_ep_interrupt_proceed(priv_dev->eps[index]);
> + reg &= ~bit_mask;
> + ret = IRQ_HANDLED;
> + } while (reg);

use for_each_set_bit() here.

> +void cdns3_ep_config(struct cdns3_endpoint *priv_ep)
> +{
> + bool is_iso_ep = (priv_ep->type == USB_ENDPOINT_XFER_ISOC);
> + struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
> + u32 bEndpointAddress = priv_ep->num | priv_ep->dir;
> + u32 interrupt_mask = EP_STS_EN_TRBERREN;
> + u32 max_packet_size = 0;
> + u32 ep_cfg = 0;
> + int ret;
> +
> + if (!priv_ep->dir)
> + interrupt_mask |= EP_STS_EN_DESCMISEN;
> +
> + if (priv_ep->type == USB_ENDPOINT_XFER_INT) {

you can turn tis into a switch statement. It'll look nicer

> + ep_cfg = EP_CFG_EPTYPE(USB_ENDPOINT_XFER_INT);
> + } else if (priv_ep->type == USB_ENDPOINT_XFER_BULK) {
> + ep_cfg = EP_CFG_EPTYPE(USB_ENDPOINT_XFER_BULK);
> + } else {
> + ep_cfg = EP_CFG_EPTYPE(USB_ENDPOINT_XFER_ISOC);
> + interrupt_mask = 0xFFFFFFFF;
> + }
> +
> + switch (priv_dev->gadget.speed) {
> + case USB_SPEED_FULL:
> + max_packet_size = is_iso_ep ? 1023 : 64;
> + break;
> + case USB_SPEED_HIGH:
> + max_packet_size = is_iso_ep ? 1024 : 512;
> + break;
> + case USB_SPEED_SUPER:
> + max_packet_size = 1024;
> + break;
> + default:
> + /* all other speed are not supported */
> + return;
> + }
> +
> + ret = cdns3_ep_onchip_buffer_reserve(priv_dev, CDNS3_EP_BUF_SIZE);
> + if (ret) {
> + dev_err(priv_dev->dev, "onchip mem is full, ep is invalid\n");
> + return;
> + }
> +
> + ep_cfg |= EP_CFG_MAXPKTSIZE(max_packet_size) |
> + EP_CFG_BUFFERING(CDNS3_EP_BUF_SIZE - 1) |
> + EP_CFG_MAXBURST(priv_ep->endpoint.maxburst);
> +
> + cdns3_select_ep(priv_dev, bEndpointAddress);
> +
> + writel(ep_cfg, &priv_dev->regs->ep_cfg);
> + writel(interrupt_mask, &priv_dev->regs->ep_sts_en);
> +
> + dev_dbg(priv_dev->dev, "Configure %s: with val %08x\n",
> + priv_ep->name, ep_cfg);
> +
> + /* enable interrupt for selected endpoint */
> + cdns3_set_register_bit(&priv_dev->regs->ep_ien,
> + cdns3_ep_addr_to_bit_pos(bEndpointAddress));
> +}

--
balbi

Attachments:

signature.asc (847.00 B)

2018-12-11 12:18:02

[permalink] [raw]

Subject: RE: [PATCH v1 2/2] usb:cdns3 Add Cadence USB3 DRD Driver

Hi,

Pawel Laszczak <[email protected]> writes:
>>I think what Felipe meant was to only combine the gadget driver code into one patch.
>>
>>The series could be split into 6 patches like so.
>>-dt binding
>>-pci glue
>>-core driver
>>-host driver
>>-gadget driver
>>-drd driver
>
> Felipe wrote:
> "
> Frankly, I don't understand why this is a series. It's a single driver
> and splitting it into a series just makes it more difficult to review,
> actually.
>
> Sure, a single patch will be large, but there's no way to have a
> functional driver until all patches are applied, anyway.
> "
>
> Felipe should I split this driver as suggested by Roger ?.
> Now it's very big patch but it's still a single driver.

don't bother. It's far easier to review as it is.

--
balbi

Attachments:

signature.asc (847.00 B)

2018-12-11 19:07:23

[permalink] [raw]

Subject: RE: [PATCH v1 2/2] usb:cdns3 Add Cadence USB3 DRD Driver

Hi,
>
>Pawel Laszczak <[email protected]> writes:
>> +static int cdns3_probe(struct platform_device *pdev)
>> +{
>> + struct device *dev = &pdev->dev;
>> + struct resource *res;
>> + struct cdns3 *cdns;
>> + void __iomem *regs;
>> + int ret;
>> +
>> + cdns = devm_kzalloc(dev, sizeof(*cdns), GFP_KERNEL);
>> + if (!cdns)
>> + return -ENOMEM;
>> +
>> + cdns->dev = dev;
>> +
>> + platform_set_drvdata(pdev, cdns);
>> +
>> + res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
>> + if (!res) {
>> + dev_err(dev, "missing IRQ\n");
>> + return -ENODEV;
>> + }
>> + cdns->irq = res->start;
>> +
>> + cdns->xhci_res[0] = *res;
>> +
>> + /*
>> + * Request memory region
>> + * region-0: xHCI
>> + * region-1: Peripheral
>> + * region-2: OTG registers
>> + */
>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>> + cdns->xhci_res[1] = *res;
>> +
>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
>> + regs = devm_ioremap_resource(dev, res);
>> + if (IS_ERR(regs))
>> + return PTR_ERR(regs);
>> + cdns->dev_regs = regs;
>> +
>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
>> + regs = devm_ioremap_resource(dev, res);
>> + if (IS_ERR(regs))
>> + return PTR_ERR(regs);
>> + cdns->otg_regs = regs;
>> +
>> + mutex_init(&cdns->mutex);
>> +
>> + cdns->phy = devm_phy_get(dev, "cdns3,usbphy");
>> + if (IS_ERR(cdns->phy)) {
>> + ret = PTR_ERR(cdns->phy);
>> + if (ret == -ENOSYS || ret == -ENODEV) {
>
>Are you sure you can get ENOSYS here? Have you checked output of
>checkpatch --strict?
Yes this error code can be returned by related to phy function if CONFIG_GENERIC_PHY is disabled.

I have seen this warning in output of checkpatch --strict .
>
>-:852: WARNING: ENOSYS means 'invalid syscall nr' and nothing else
>
>> +#ifdef CONFIG_PM_SLEEP
>> +static int cdns3_suspend(struct device *dev)
>> +{
>> + /* TODO: Implements this function. */
>> + return 0;
>> +}
>> +
>> +static int cdns3_resume(struct device *dev)
>> +{
>> + /* TODO: Implements this function. */
>> + return 0;
>> +}
>> +#endif /* CONFIG_PM_SLEEP */
>> +static int cdns3_runtime_suspend(struct device *dev)
>> +{ /* TODO: Implements this function. */
>> + return 0;
>> +}
>> +
>> +static int cdns3_runtime_resume(struct device *dev)
>> +{
>> + /* TODO: Implements this function. */
>> + return 0;
>> +}
>> +#endif /* CONFIG_PM */
>
>please no TODO stubs. Just get rid of your dev_pm_ops if you don't
>implement them. Come up with a later patch adding a proper
>implementation for PM.

Ok.

>
>> +static int __init cdns3_driver_platform_register(void)
>> +{
>> + return platform_driver_register(&cdns3_driver);
>> +}
>> +module_init(cdns3_driver_platform_register);
>> +
>> +static void __exit cdns3_driver_platform_unregister(void)
>> +{
>> + platform_driver_unregister(&cdns3_driver);
>> +}
>> +module_exit(cdns3_driver_platform_unregister);
>
>module_platform_driver()

Ok,

>
>> diff --git a/drivers/usb/cdns3/debug.h b/drivers/usb/cdns3/debug.h
>> new file mode 100644
>> index 000000000000..afb81d224718
>> --- /dev/null
>> +++ b/drivers/usb/cdns3/debug.h
>> @@ -0,0 +1,346 @@
>> +/* SPDX-License-Identifier: GPL-2.0 */
>> +/*
>> + * Cadence USBSS DRD Driver.
>> + * Debug header file.
>> + *
>> + * Copyright (C) 2018 Cadence.
>> + *
>> + * Author: Pawel Laszczak <[email protected]>
>> + */
>> +#ifndef __LINUX_CDNS3_DEBUG
>> +#define __LINUX_CDNS3_DEBUG
>> +#include "gadget.h"
>> +
>> +static inline void cdns3_decode_get_status(u8 bRequestType, u16 wIndex,
>> + u16 wLength, char *str)
>> +{
>> + switch (bRequestType & USB_RECIP_MASK) {
>> + case USB_RECIP_INTERFACE:
>> + sprintf(str, "Get Interface Status Intf = %d, L: = %d",
>> + wIndex, wLength);
>> + break;
>> + case USB_RECIP_ENDPOINT:
>> + sprintf(str, "Get Endpoint Status ep%d%s",
>> + wIndex & ~USB_DIR_IN,
>> + wIndex & USB_DIR_IN ? "in" : "out");
>> + break;
>> + }
>> +}
>> +
>> +static inline const char *cdns3_decode_device_feature(u16 wValue)
>> +{
>> + switch (wValue) {
>> + case USB_DEVICE_SELF_POWERED:
>> + return "Self Powered";
>> + case USB_DEVICE_REMOTE_WAKEUP:
>> + return "Remote Wakeup";
>> + case USB_DEVICE_TEST_MODE:
>> + return "Test Mode";
>> + case USB_DEVICE_U1_ENABLE:
>> + return "U1 Enable";
>> + case USB_DEVICE_U2_ENABLE:
>> + return "U2 Enable";
>> + case USB_DEVICE_LTM_ENABLE:
>> + return "LTM Enable";
>> + default:
>> + return "UNKNOWN";
>> + }
>> +}
>> +
>> +static inline const char *cdns3_decode_test_mode(u16 wIndex)
>> +{
>> + switch (wIndex) {
>> + case TEST_J:
>> + return ": TEST_J";
>> + case TEST_K:
>> + return ": TEST_K";
>> + case TEST_SE0_NAK:
>> + return ": TEST_SE0_NAK";
>> + case TEST_PACKET:
>> + return ": TEST_PACKET";
>> + case TEST_FORCE_EN:
>> + return ": TEST_FORCE_EN";
>> + default:
>> + return ": UNKNOWN";
>> + }
>> +}
>> +
>> +static inline void cdns3_decode_set_clear_feature(u8 bRequestType, u8 bRequest,
>> + u16 wValue, u16 wIndex,
>> + char *str)
>> +{
>> + switch (bRequestType & USB_RECIP_MASK) {
>> + case USB_RECIP_DEVICE:
>> + sprintf(str, "%s Device Feature(%s%s)",
>> + bRequest == USB_REQ_CLEAR_FEATURE ? "Clear" : "Set",
>> + cdns3_decode_device_feature(wValue),
>> + wValue == USB_DEVICE_TEST_MODE ?
>> + cdns3_decode_test_mode(wIndex) : "");
>> + break;
>> + case USB_RECIP_INTERFACE:
>> + sprintf(str, "%s Interface Feature(%s)",
>> + bRequest == USB_REQ_CLEAR_FEATURE ? "Clear" : "Set",
>> + wIndex == USB_INTRF_FUNC_SUSPEND ?
>> + "Function Suspend" : "UNKNOWN");
>> + break;
>> + case USB_RECIP_ENDPOINT:
>> + sprintf(str, "%s Endpoint Feature(%s ep%d%s)",
>> + bRequest == USB_REQ_CLEAR_FEATURE ? "Clear" : "Set",
>> + wIndex == USB_ENDPOINT_HALT ? "Halt" : "UNKNOWN",
>> + wIndex & ~USB_DIR_IN,
>> + wIndex & USB_DIR_IN ? "in" : "out");
>> + break;
>> + }
>> +}
>> +
>> +static inline const char *cdns3_decode_descriptor(u16 wValue)
>> +{
>> + switch (wValue >> 8) {
>> + case USB_DT_DEVICE:
>> + return "Device";
>> + case USB_DT_CONFIG:
>> + return "Configuration";
>> + case USB_DT_STRING:
>> + return "String";
>> + case USB_DT_INTERFACE:
>> + return "Interface";
>> + case USB_DT_ENDPOINT:
>> + return "Endpoint";
>> + case USB_DT_DEVICE_QUALIFIER:
>> + return "Device Qualifier";
>> + case USB_DT_OTHER_SPEED_CONFIG:
>> + return "Other Speed Config";
>> + case USB_DT_INTERFACE_POWER:
>> + return "Interface Power";
>> + case USB_DT_OTG:
>> + return "OTG";
>> + case USB_DT_DEBUG:
>> + return "Debug";
>> + case USB_DT_INTERFACE_ASSOCIATION:
>> + return "Interface Association";
>> + case USB_DT_BOS:
>> + return "BOS";
>> + case USB_DT_DEVICE_CAPABILITY:
>> + return "Device Capability";
>> + case USB_DT_SS_ENDPOINT_COMP:
>> + return "SS Endpoint Companion";
>> + case USB_DT_SSP_ISOC_ENDPOINT_COMP:
>> + return "SSP Isochronous Endpoint Companion";
>> + default:
>> + return "UNKNOWN";
>> + }
>> +}
>> +
>> +/**
>> + * cdns3_decode_ctrl - returns a string represetion of ctrl request
>> + */
>> +static inline const char *cdns3_decode_ctrl(char *str, u8 bRequestType,
>> + u8 bRequest, u16 wValue,
>> + u16 wIndex, u16 wLength)
>> +{
>> + switch (bRequest) {
>> + case USB_REQ_GET_STATUS:
>> + cdns3_decode_get_status(bRequestType, wIndex,
>> + wLength, str);
>> + break;
>> + case USB_REQ_CLEAR_FEATURE:
>> + case USB_REQ_SET_FEATURE:
>> + cdns3_decode_set_clear_feature(bRequestType, bRequest,
>> + wValue, wIndex, str);
>> + break;
>> + case USB_REQ_SET_ADDRESS:
>> + sprintf(str, "Set Address Addr: %02x", wValue);
>> + break;
>> + case USB_REQ_GET_DESCRIPTOR:
>> + sprintf(str, "GET %s Descriptor I: %d, L: %d",
>> + cdns3_decode_descriptor(wValue),
>> + wValue & 0xff, wLength);
>> + break;
>> + case USB_REQ_SET_DESCRIPTOR:
>> + sprintf(str, "SET %s Descriptor I: %d, L: %d",
>> + cdns3_decode_descriptor(wValue),
>> + wValue & 0xff, wLength);
>> + break;
>> + case USB_REQ_GET_CONFIGURATION:
>> + sprintf(str, "Get Configuration L: %d", wLength);
>> + break;
>> + case USB_REQ_SET_CONFIGURATION:
>> + sprintf(str, "Set Configuration Config: %d ", wValue);
>> + break;
>> + case USB_REQ_GET_INTERFACE:
>> + sprintf(str, "Get Interface Intf: %d, L: %d", wIndex, wLength);
>> + break;
>> + case USB_REQ_SET_INTERFACE:
>> + sprintf(str, "Set Interface Intf: %d, Alt: %d", wIndex, wValue);
>> + break;
>> + case USB_REQ_SYNCH_FRAME:
>> + sprintf(str, "Synch Frame Ep: %d, L: %d", wIndex, wLength);
>> + break;
>> + case USB_REQ_SET_SEL:
>> + sprintf(str, "Set SEL L: %d", wLength);
>> + break;
>> + case USB_REQ_SET_ISOCH_DELAY:
>> + sprintf(str, "Set Isochronous Delay Delay: %d ns", wValue);
>> + break;
>> + default:
>> + sprintf(str,
>> + "SETUP BRT: %02x BR: %02x V: %04x I: %04x L: %04x\n",
>> + bRequestType, bRequest,
>> + wValue, wIndex, wLength);
>> + }
>> +
>> + return str;
>> +}
>
>All of these are a flat out copy of dwc3's implementation. It's much,
>much better to turn dwc3's implementation into a generic, reusable
>library function then spinning your own as a duplicated effort.
I agree,
It would be nice to have a set of decoding function in some generic library. It could be used
also by other drivers.
Who should do this ?

>
>> diff --git a/drivers/usb/cdns3/ep0.c b/drivers/usb/cdns3/ep0.c
>> new file mode 100644
>> index 000000000000..1ef0e9f73e3e
>> --- /dev/null
>> +++ b/drivers/usb/cdns3/ep0.c
>> @@ -0,0 +1,864 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/*
>> + * Cadence USBSS DRD Driver - gadget side.
>> + *
>> + * Copyright (C) 2018 Cadence Design Systems.
>> + * Copyright (C) 2017-2018 NXP
>> + *
>> + * Authors: Pawel Jez <[email protected]>,
>> + * Pawel Laszczak <[email protected]>
>> + * Peter Chen <[email protected]>
>> + */
>> +
>> +#include <linux/usb/composite.h>
>> +
>> +#include "gadget.h"
>> +#include "trace.h"
>> +
>> +static struct usb_endpoint_descriptor cdns3_gadget_ep0_desc = {
>> + .bLength = USB_DT_ENDPOINT_SIZE,
>> + .bDescriptorType = USB_DT_ENDPOINT,
>> + .bmAttributes = USB_ENDPOINT_XFER_CONTROL,
>> +};
>> +
>> +/**
>> + * cdns3_ep0_run_transfer - Do transfer on default endpoint hardware
>> + * @priv_dev: extended gadget object
>> + * @dma_addr: physical address where data is/will be stored
>> + * @length: data length
>> + * @erdy: set it to 1 when ERDY packet should be sent -
>> + * exit from flow control state
>> + */
>> +static void cdns3_ep0_run_transfer(struct cdns3_device *priv_dev,
>> + dma_addr_t dma_addr,
>> + unsigned int length, int erdy)
>> +{
>> + struct cdns3_usb_regs __iomem *regs = priv_dev->regs;
>> + struct cdns3_endpoint *priv_ep = ep_to_cdns3_ep(priv_dev->gadget.ep0);
>> +
>> + priv_dev->ep0_trb->buffer = TRB_BUFFER(dma_addr);
>> + priv_dev->ep0_trb->length = TRB_LEN(length);
>> + priv_dev->ep0_trb->control = TRB_CYCLE | TRB_IOC | TRB_TYPE(TRB_NORMAL);
>> +
>> + trace_cdns3_prepare_trb(priv_ep, priv_dev->ep0_trb);
>> +
>> + cdns3_select_ep(priv_dev, priv_dev->ep0_data_dir);
>> +
>> + writel(EP_STS_TRBERR, &regs->ep_sts);
>> + writel(EP_TRADDR_TRADDR(priv_dev->ep0_trb_dma), &regs->ep_traddr);
>> + trace_cdns3_doorbell_ep0(priv_dev->ep0_data_dir ? "ep0in" : "ep0out");
>> +
>> + /* TRB should be prepared before starting transfer */
>> + writel(EP_CMD_DRDY, &regs->ep_cmd);
>> +
>> + if (erdy)
>> + writel(EP_CMD_ERDY, &priv_dev->regs->ep_cmd);
>> +}
>> +
>> +/**
>> + * cdns3_ep0_delegate_req - Returns status of handling setup packet
>> + * Setup is handled by gadget driver
>> + * @priv_dev: extended gadget object
>> + * @ctrl_req: pointer to received setup packet
>> + *
>> + * Returns zero on success or negative value on failure
>> + */
>> +static int cdns3_ep0_delegate_req(struct cdns3_device *priv_dev,
>> + struct usb_ctrlrequest *ctrl_req)
>> +{
>> + int ret;
>> +
>> + spin_unlock(&priv_dev->lock);
>> + priv_dev->setup_pending = 1;
>> + ret = priv_dev->gadget_driver->setup(&priv_dev->gadget, ctrl_req);
>> + priv_dev->setup_pending = 0;
>> + spin_lock(&priv_dev->lock);
>> + return ret;
>> +}
>> +
>> +static void cdns3_prepare_setup_packet(struct cdns3_device *priv_dev)
>> +{
>> + priv_dev->ep0_data_dir = 0;
>> + cdns3_ep0_run_transfer(priv_dev, priv_dev->setup_dma,
>> + sizeof(struct usb_ctrlrequest), 0);
>> +}
>> +
>> +/**
>> + * cdns3_req_ep0_set_configuration - Handling of SET_CONFIG standard USB request
>> + * @priv_dev: extended gadget object
>> + * @ctrl_req: pointer to received setup packet
>> + *
>> + * Returns 0 if success, USB_GADGET_DELAYED_STATUS on deferred status stage,
>> + * error code on error
>> + */
>> +static int cdns3_req_ep0_set_configuration(struct cdns3_device *priv_dev,
>> + struct usb_ctrlrequest *ctrl_req)
>> +{
>> + enum usb_device_state device_state = priv_dev->gadget.state;
>> + struct cdns3_endpoint *priv_ep;
>> + u32 config = le16_to_cpu(ctrl_req->wValue);
>> + int result = 0;
>> + int i;
>> +
>> + switch (device_state) {
>> + case USB_STATE_ADDRESS:
>> + /* Configure non-control EPs */
>> + for (i = 0; i < CDNS3_ENDPOINTS_MAX_COUNT; i++) {
>> + priv_ep = priv_dev->eps[i];
>> + if (!priv_ep)
>> + continue;
>> +
>> + if (priv_ep->flags & EP_CLAIMED)
>> + cdns3_ep_config(priv_ep);
>> + }
>> +
>> + result = cdns3_ep0_delegate_req(priv_dev, ctrl_req);
>> +
>> + if (result)
>> + return result;
>> +
>> + if (config) {
>> + cdns3_set_hw_configuration(priv_dev);
>> + } else {
>> + cdns3_gadget_unconfig(priv_dev);
>> + usb_gadget_set_state(&priv_dev->gadget,
>> + USB_STATE_ADDRESS);
>
>this is wrong. If address is zero, state should be default, not
>addressed. Addressed would be used on the other branch here, when you
>have a non-zero address

If address is zero then state should be USB_STATE_DEFAULT. Driver enters to this branch
only if gadget.state = USB_STATE_ADDRESS (address != 0). This state can be changed in composite.c file
after delegating request to gadget driver. Because this state could be changed driver simple
restore USB_STATE_ADDRESS if config = 0.

>
>> + }
>> + break;
>> + case USB_STATE_CONFIGURED:
>
>where do you set this state?
It's set in set_config in composite.c file.
>
>> +static int cdns3_ep0_feature_handle_device(struct cdns3_device *priv_dev,
>> + struct usb_ctrlrequest *ctrl,
>> + int set)
>> +{
>> + enum usb_device_state state;
>> + enum usb_device_speed speed;
>> + int ret = 0;
>> + u32 wValue;
>> + u32 wIndex;
>> + u16 tmode;
>> +
>> + wValue = le16_to_cpu(ctrl->wValue);
>> + wIndex = le16_to_cpu(ctrl->wIndex);
>> + state = priv_dev->gadget.state;
>> + speed = priv_dev->gadget.speed;
>> +
>> + switch (ctrl->wValue) {
>> + case USB_DEVICE_REMOTE_WAKEUP:
>> + priv_dev->wake_up_flag = !!set;
>> + break;
>> + case USB_DEVICE_U1_ENABLE:
>> + if (state != USB_STATE_CONFIGURED || speed != USB_SPEED_SUPER)
>> + return -EINVAL;
>> +
>> + priv_dev->u1_allowed = !!set;
>> + break;
>> + case USB_DEVICE_U2_ENABLE:
>> + if (state != USB_STATE_CONFIGURED || speed != USB_SPEED_SUPER)
>> + return -EINVAL;
>> +
>> + priv_dev->u2_allowed = !!set;
>> + break;
>> + case USB_DEVICE_LTM_ENABLE:
>> + ret = -EINVAL;
>> + break;
>> + case USB_DEVICE_TEST_MODE:
>> + if (state != USB_STATE_CONFIGURED || speed > USB_SPEED_HIGH)
>> + return -EINVAL;
>> +
>> + tmode = le16_to_cpu(ctrl->wIndex);
>> +
>> + if (!set || (tmode & 0xff) != 0)
>> + return -EINVAL;
>> +
>> + switch (tmode >> 8) {
>> + case TEST_J:
>> + case TEST_K:
>> + case TEST_SE0_NAK:
>> + case TEST_PACKET:
>> + cdns3_set_register_bit(&priv_dev->regs->usb_cmd,
>> + USB_CMD_STMODE |
>> + USB_STS_TMODE_SEL(tmode - 1));
>
>I'm 90% sure this won't work. There's a reason why we only enter the
>requested test mode from status stage. How have you tested this?

From USB spec:
"The transition to test mode must be complete no later than 3 ms after the completion of the status stage of the
request."
But I don't remember any issues with this test on other ours drivers. Maybe status stage
is armed in this case by controller. I have to confirm how it works with hardware team.
Driver doesn't know when status stage was completed. We don't have
any event on status stage completion. I haven't checked it yet with tester on this driver.

>
>> diff --git a/drivers/usb/cdns3/gadget.c b/drivers/usb/cdns3/gadget.c
>> new file mode 100644
>> index 000000000000..a021eaf07aee
>> --- /dev/null
>> +++ b/drivers/usb/cdns3/gadget.c
>
><snip>
>
>> +struct usb_request *cdns3_next_request(struct list_head *list)
>> +{
>> + if (list_empty(list))
>> + return NULL;
>> + return list_first_entry(list, struct usb_request, list);
>
>list_first_entry_or_null()

Ok.
>
>> +void cdns3_gadget_unconfig(struct cdns3_device *priv_dev)
>> +{
>> + /* RESET CONFIGURATION */
>> + writel(USB_CONF_CFGRST, &priv_dev->regs->usb_conf);
>> +
>> + cdns3_allow_enable_l1(priv_dev, 0);
>> + priv_dev->hw_configured_flag = 0;
>> + priv_dev->onchip_mem_allocated_size = 0;
>
>clear all test modes? Reset ep0 max_packet_size to 512?
Test mode should be reset automatically on exit.
W can't clear this mode in register. It's WAC (write only and auto clear) bit.
This function only reset endpoint configuration in controller register.
Ep0 max_packet_size should be unchanged here. Ep0 max_packet it's updated on
Connect/Disconnect/Reset events.

Maybe this function should be called cdns3_hw_reset_eps_config.
It doesn't unconfigure whole gadget but only reset endpoints configuration kept by
controller.
I will change this function.

>
>> +static irqreturn_t cdns3_device_irq_handler(int irq, void *data)
>> +{
>> + struct cdns3_device *priv_dev;
>> + struct cdns3 *cdns = data;
>> + irqreturn_t ret = IRQ_NONE;
>> + unsigned long flags;
>> + u32 reg;
>> +
>> + priv_dev = cdns->gadget_dev;
>> + spin_lock_irqsave(&priv_dev->lock, flags);
>
>you're already running in hardirq context. Why do you need this lock at
>all? I would be better to use the hardirq handler to mask your
>interrupts, so they don't fire again, then used the top-half (softirq)
>handler to actually handle the interrupts.

Yes, spin_lock_irqsave is not necessary here.

Do you mean replacing devm_request_irq with a request_threaded_irq ?
I have single interrupt line shared between Host, Driver, DRD/OTG.
I'm not sure if it will work more efficiently.

>
>> + /* check USB device interrupt */
>> + reg = readl(&priv_dev->regs->usb_ists);
>> + writel(reg, &priv_dev->regs->usb_ists);
>> +
>> + if (reg) {
>> + dev_dbg(priv_dev->dev, "IRQ: usb_ists: %08X\n", reg);
>
>I strongly advise against using dev_dbg() for debugging. Even more so
>inside your IRQ handler.
Ok, It's not necessary in this place, especially, that there is invoked trace point
inside cdns3_check_usb_interrupt_proceed which makes the same.

>
>> + cdns3_check_usb_interrupt_proceed(priv_dev, reg);
>> + ret = IRQ_HANDLED;
>> + }
>> +
>> + /* check endpoint interrupt */
>> + reg = readl(&priv_dev->regs->ep_ists);
>> +
>> + /* handle default endpoint OUT */
>> + if (reg & EP_ISTS_EP_OUT0) {
>> + cdns3_check_ep0_interrupt_proceed(priv_dev, USB_DIR_OUT);
>> + ret = IRQ_HANDLED;
>> + }
>> +
>> + /* handle default endpoint IN */
>> + if (reg & EP_ISTS_EP_IN0) {
>> + cdns3_check_ep0_interrupt_proceed(priv_dev, USB_DIR_IN);
>> + ret = IRQ_HANDLED;
>> + }
>> +
>> + /* check if interrupt from non default endpoint, if no exit */
>> + reg &= ~(EP_ISTS_EP_OUT0 | EP_ISTS_EP_IN0);
>> + if (!reg)
>> + goto irqend;
>> +
>> + do {
>> + unsigned int bit_pos = ffs(reg);
>> + u32 bit_mask = 1 << (bit_pos - 1);
>> + int index;
>> +
>> + index = cdns3_ep_reg_pos_to_index(bit_pos);
>> + cdns3_check_ep_interrupt_proceed(priv_dev->eps[index]);
>> + reg &= ~bit_mask;
>> + ret = IRQ_HANDLED;
>> + } while (reg);
>
>use for_each_set_bit() here.
Ok

>
>> +void cdns3_ep_config(struct cdns3_endpoint *priv_ep)
>> +{
>> + bool is_iso_ep = (priv_ep->type == USB_ENDPOINT_XFER_ISOC);
>> + struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
>> + u32 bEndpointAddress = priv_ep->num | priv_ep->dir;
>> + u32 interrupt_mask = EP_STS_EN_TRBERREN;
>> + u32 max_packet_size = 0;
>> + u32 ep_cfg = 0;
>> + int ret;
>> +
>> + if (!priv_ep->dir)
>> + interrupt_mask |= EP_STS_EN_DESCMISEN;
>> +
>> + if (priv_ep->type == USB_ENDPOINT_XFER_INT) {
>
>you can turn tis into a switch statement. It'll look nicer
Ok.
>
>> + ep_cfg = EP_CFG_EPTYPE(USB_ENDPOINT_XFER_INT);
>> + } else if (priv_ep->type == USB_ENDPOINT_XFER_BULK) {
>> + ep_cfg = EP_CFG_EPTYPE(USB_ENDPOINT_XFER_BULK);
>> + } else {
>> + ep_cfg = EP_CFG_EPTYPE(USB_ENDPOINT_XFER_ISOC);
>> + interrupt_mask = 0xFFFFFFFF;
>> + }
>> +
>> + switch (priv_dev->gadget.speed) {
>> + case USB_SPEED_FULL:
>> + max_packet_size = is_iso_ep ? 1023 : 64;
>> + break;
>> + case USB_SPEED_HIGH:
>> + max_packet_size = is_iso_ep ? 1024 : 512;
>> + break;
>> + case USB_SPEED_SUPER:
>> + max_packet_size = 1024;
>> + break;
>> + default:
>> + /* all other speed are not supported */
>> + return;
>> + }
>> +
>> + ret = cdns3_ep_onchip_buffer_reserve(priv_dev, CDNS3_EP_BUF_SIZE);
>> + if (ret) {
>> + dev_err(priv_dev->dev, "onchip mem is full, ep is invalid\n");
>> + return;
>> + }
>> +
>> + ep_cfg |= EP_CFG_MAXPKTSIZE(max_packet_size) |
>> + EP_CFG_BUFFERING(CDNS3_EP_BUF_SIZE - 1) |
>> + EP_CFG_MAXBURST(priv_ep->endpoint.maxburst);
>> +
>> + cdns3_select_ep(priv_dev, bEndpointAddress);
>> +
>> + writel(ep_cfg, &priv_dev->regs->ep_cfg);
>> + writel(interrupt_mask, &priv_dev->regs->ep_sts_en);
>> +
>> + dev_dbg(priv_dev->dev, "Configure %s: with val %08x\n",
>> + priv_ep->name, ep_cfg);
>> +
>> + /* enable interrupt for selected endpoint */
>> + cdns3_set_register_bit(&priv_dev->regs->ep_ien,
>> + cdns3_ep_addr_to_bit_pos(bEndpointAddress));
>> +}
>
>--
Thanks
Pawell

2018-12-12 02:06:11

[permalink] [raw]

Subject: Re: [PATCH v1 2/2] usb:cdns3 Add Cadence USB3 DRD Driver

> >> + tmode = le16_to_cpu(ctrl->wIndex);
> >> +
> >> + if (!set || (tmode & 0xff) != 0)
> >> + return -EINVAL;
> >> +
> >> + switch (tmode >> 8) {
> >> + case TEST_J:
> >> + case TEST_K:
> >> + case TEST_SE0_NAK:
> >> + case TEST_PACKET:
> >> + cdns3_set_register_bit(&priv_dev->regs->usb_cmd,
> >> + USB_CMD_STMODE |
> >> + USB_STS_TMODE_SEL(tmode - 1));
> >
> >I'm 90% sure this won't work. There's a reason why we only enter the
> >requested test mode from status stage. How have you tested this?
>

What's the reason?
It can work although the code is a little different with above, I
tested it using USBxHSETT tool at Windows.

> From USB spec:
> "The transition to test mode must be complete no later than 3 ms after the completion of the status stage of the
> request."
> But I don't remember any issues with this test on other ours drivers. Maybe status stage
> is armed in this case by controller. I have to confirm how it works with hardware team.
> Driver doesn't know when status stage was completed. We don't have
> any event on status stage completion. I haven't checked it yet with tester on this driver.
>

> >> + irqreturn_t ret = IRQ_NONE;
> >> + unsigned long flags;
> >> + u32 reg;
> >> +
> >> + priv_dev = cdns->gadget_dev;
> >> + spin_lock_irqsave(&priv_dev->lock, flags);
> >
> >you're already running in hardirq context. Why do you need this lock at
> >all? I would be better to use the hardirq handler to mask your
> >interrupts, so they don't fire again, then used the top-half (softirq)
> >handler to actually handle the interrupts.
>

This controller may be ran at SMP environment, register and flag access
needs to be protected among CPUs running.

> Yes, spin_lock_irqsave is not necessary here.
>
> Do you mean replacing devm_request_irq with a request_threaded_irq ?
> I have single interrupt line shared between Host, Driver, DRD/OTG.
> I'm not sure if it will work more efficiently.
>
> >
> >> + /* check USB device interrupt */
> >> + reg = readl(&priv_dev->regs->usb_ists);
> >> + writel(reg, &priv_dev->regs->usb_ists);
> >> +
> >> + if (reg) {
> >> + dev_dbg(priv_dev->dev, "IRQ: usb_ists: %08X\n", reg);
> >
> >I strongly advise against using dev_dbg() for debugging. Even more so
> >inside your IRQ handler.

Felipe, I use Dynamic Debug for debugging, and show debug messages with
"dmesg" after testing/debugging. I see dwc3 using trace, any benefits
for switching
to trace?

> Ok, It's not necessary in this place, especially, that there is invoked trace point
> inside cdns3_check_usb_interrupt_proceed which makes the same.
>

Peter

2018-12-12 06:53:34

[permalink] [raw]

Subject: RE: [PATCH v1 2/2] usb:cdns3 Add Cadence USB3 DRD Driver

Hi

Pawel Laszczak <[email protected]> writes:
>>> + cdns->phy = devm_phy_get(dev, "cdns3,usbphy");
>>> + if (IS_ERR(cdns->phy)) {
>>> + ret = PTR_ERR(cdns->phy);
>>> + if (ret == -ENOSYS || ret == -ENODEV) {
>>
>>Are you sure you can get ENOSYS here? Have you checked output of
>>checkpatch --strict?
>>-:852: WARNING: ENOSYS means 'invalid syscall nr' and nothing else
>
> Yes this error code can be returned by related to phy function if
> CONFIG_GENERIC_PHY is disabled.
>
> I have seen this warning in output of checkpatch --strict .

Kishon, seems like you shouldn't be using that error value.

<snip>

>>> + case USB_REQ_SET_ISOCH_DELAY:
>>> + sprintf(str, "Set Isochronous Delay Delay: %d ns", wValue);
>>> + break;
>>> + default:
>>> + sprintf(str,
>>> + "SETUP BRT: %02x BR: %02x V: %04x I: %04x L: %04x\n",
>>> + bRequestType, bRequest,
>>> + wValue, wIndex, wLength);
>>> + }
>>> +
>>> + return str;
>>> +}
>>
>>All of these are a flat out copy of dwc3's implementation. It's much,
>>much better to turn dwc3's implementation into a generic, reusable
>>library function then spinning your own as a duplicated effort.
> I agree,
> It would be nice to have a set of decoding function in some generic library. It could be used
> also by other drivers.
> Who should do this ?

since you're the first to reuse it, then it should be you :-)

>>> +static int cdns3_req_ep0_set_configuration(struct cdns3_device *priv_dev,
>>> + struct usb_ctrlrequest *ctrl_req)
>>> +{
>>> + enum usb_device_state device_state = priv_dev->gadget.state;
>>> + struct cdns3_endpoint *priv_ep;
>>> + u32 config = le16_to_cpu(ctrl_req->wValue);
>>> + int result = 0;
>>> + int i;
>>> +
>>> + switch (device_state) {
>>> + case USB_STATE_ADDRESS:
>>> + /* Configure non-control EPs */
>>> + for (i = 0; i < CDNS3_ENDPOINTS_MAX_COUNT; i++) {
>>> + priv_ep = priv_dev->eps[i];
>>> + if (!priv_ep)
>>> + continue;
>>> +
>>> + if (priv_ep->flags & EP_CLAIMED)
>>> + cdns3_ep_config(priv_ep);
>>> + }
>>> +
>>> + result = cdns3_ep0_delegate_req(priv_dev, ctrl_req);
>>> +
>>> + if (result)
>>> + return result;
>>> +
>>> + if (config) {
>>> + cdns3_set_hw_configuration(priv_dev);
>>> + } else {
>>> + cdns3_gadget_unconfig(priv_dev);
>>> + usb_gadget_set_state(&priv_dev->gadget,
>>> + USB_STATE_ADDRESS);
>>
>>this is wrong. If address is zero, state should be default, not
>>addressed. Addressed would be used on the other branch here, when you
>>have a non-zero address
>
> If address is zero then state should be USB_STATE_DEFAULT. Driver
> enters to this branch only if gadget.state = USB_STATE_ADDRESS
> (address != 0). This state can be changed in composite.c file after
> delegating request to gadget driver. Because this state could be
> changed driver simple restore USB_STATE_ADDRESS if config = 0.

nevermind, I read this as being the handler for Set Address. This is Set
Config, instead.

>>> + }
>>> + break;
>>> + case USB_STATE_CONFIGURED:
>>
>>where do you set this state?
> It's set in set_config in composite.c file.

indeed

>>> + case USB_DEVICE_TEST_MODE:
>>> + if (state != USB_STATE_CONFIGURED || speed > USB_SPEED_HIGH)
>>> + return -EINVAL;
>>> +
>>> + tmode = le16_to_cpu(ctrl->wIndex);
>>> +
>>> + if (!set || (tmode & 0xff) != 0)
>>> + return -EINVAL;
>>> +
>>> + switch (tmode >> 8) {
>>> + case TEST_J:
>>> + case TEST_K:
>>> + case TEST_SE0_NAK:
>>> + case TEST_PACKET:
>>> + cdns3_set_register_bit(&priv_dev->regs->usb_cmd,
>>> + USB_CMD_STMODE |
>>> + USB_STS_TMODE_SEL(tmode - 1));
>>
>>I'm 90% sure this won't work. There's a reason why we only enter the
>>requested test mode from status stage. How have you tested this?
>
> From USB spec:
> "The transition to test mode must be complete no later than 3 ms after the completion of the status stage of the
> request."

exactly, _after_ completion of status stage :-)

> But I don't remember any issues with this test on other ours
> drivers. Maybe status stage is armed in this case by controller. I
> have to confirm how it works with hardware team. Driver doesn't know
> when status stage was completed. We don't have any event on status
> stage completion. I haven't checked it yet with tester on this
> driver.

Let's consider the scenario where you're requesting Test_Packet mode. If
you start transmitting the test pattern from setup stage, how can you
even transmit status stage?

>>> +void cdns3_gadget_unconfig(struct cdns3_device *priv_dev)
>>> +{
>>> + /* RESET CONFIGURATION */
>>> + writel(USB_CONF_CFGRST, &priv_dev->regs->usb_conf);
>>> +
>>> + cdns3_allow_enable_l1(priv_dev, 0);
>>> + priv_dev->hw_configured_flag = 0;
>>> + priv_dev->onchip_mem_allocated_size = 0;
>>
>>clear all test modes? Reset ep0 max_packet_size to 512?
> Test mode should be reset automatically on exit.

on exit? Which exit? Did you test this on USB Reset? Did you run USBCV
on Super and High speed with any gadget?

> W can't clear this mode in register. It's WAC (write only and auto clear) bit.
> This function only reset endpoint configuration in controller register.
> Ep0 max_packet_size should be unchanged here. Ep0 max_packet it's updated on
> Connect/Disconnect/Reset events.

right, and this is called for both reset and disconnect (see below). If
you're telling me that test mode and ep0 wMaxPacketSize is handled
elsewhere, that's fine.

+ /* Disconnection detected */
+ if (usb_ists & (USB_ISTS_DIS2I | USB_ISTS_DISI)) {
+ if (priv_dev->gadget_driver &&
+ priv_dev->gadget_driver->disconnect) {
+ spin_unlock(&priv_dev->lock);
+ priv_dev->gadget_driver->disconnect(&priv_dev->gadget);
+ spin_lock(&priv_dev->lock);
+ }
+
+ priv_dev->gadget.speed = USB_SPEED_UNKNOWN;
+ usb_gadget_set_state(&priv_dev->gadget, USB_STATE_NOTATTACHED);
+ cdns3_gadget_unconfig(priv_dev);
+ }
+
+ /* reset*/
+ if (usb_ists & (USB_ISTS_UWRESI | USB_ISTS_UHRESI | USB_ISTS_U2RESI)) {
+ /*read again to check the actuall speed*/
+ speed = cdns3_get_speed(priv_dev);
+ usb_gadget_set_state(&priv_dev->gadget, USB_STATE_DEFAULT);
+ priv_dev->gadget.speed = speed;
+ cdns3_gadget_unconfig(priv_dev);
+ cdns3_ep0_config(priv_dev);
+ }

> Maybe this function should be called cdns3_hw_reset_eps_config.

perhaps

> It doesn't unconfigure whole gadget but only reset endpoints configuration kept by
> controller.
> I will change this function.

ok

>>> +static irqreturn_t cdns3_device_irq_handler(int irq, void *data)
>>> +{
>>> + struct cdns3_device *priv_dev;
>>> + struct cdns3 *cdns = data;
>>> + irqreturn_t ret = IRQ_NONE;
>>> + unsigned long flags;
>>> + u32 reg;
>>> +
>>> + priv_dev = cdns->gadget_dev;
>>> + spin_lock_irqsave(&priv_dev->lock, flags);
>>
>>you're already running in hardirq context. Why do you need this lock at
>>all? I would be better to use the hardirq handler to mask your
>>interrupts, so they don't fire again, then used the top-half (softirq)
>>handler to actually handle the interrupts.
>
> Yes, spin_lock_irqsave is not necessary here.
>
> Do you mean replacing devm_request_irq with a request_threaded_irq ?
> I have single interrupt line shared between Host, Driver, DRD/OTG.
> I'm not sure if it will work more efficiently.

The whole idea for running very little in hardirq context is to give the
scheduler a chance to decide what should run. This is important to
reduce latency when running with RT patchset applied, for
example. However, I'll give you that, it's a minor requirement. It's
just that, to me, it's a small detail that's easy to implement.

>>> + /* check USB device interrupt */
>>> + reg = readl(&priv_dev->regs->usb_ists);
>>> + writel(reg, &priv_dev->regs->usb_ists);
>>> +
>>> + if (reg) {
>>> + dev_dbg(priv_dev->dev, "IRQ: usb_ists: %08X\n", reg);
>>
>>I strongly advise against using dev_dbg() for debugging. Even more so
>>inside your IRQ handler.
> Ok, It's not necessary in this place, especially, that there is invoked trace point
> inside cdns3_check_usb_interrupt_proceed which makes the same.

overhead. Tracepoints are really, really low overhead. The string
decoding doesn't happen until you read the trace file.

--
balbi

Attachments:

signature.asc (847.00 B)

2018-12-12 06:58:11

[permalink] [raw]

Subject: Re: [PATCH v1 2/2] usb:cdns3 Add Cadence USB3 DRD Driver

Peter Chen <[email protected]> writes:

>> >> + tmode = le16_to_cpu(ctrl->wIndex);
>> >> +
>> >> + if (!set || (tmode & 0xff) != 0)
>> >> + return -EINVAL;
>> >> +
>> >> + switch (tmode >> 8) {
>> >> + case TEST_J:
>> >> + case TEST_K:
>> >> + case TEST_SE0_NAK:
>> >> + case TEST_PACKET:
>> >> + cdns3_set_register_bit(&priv_dev->regs->usb_cmd,
>> >> + USB_CMD_STMODE |
>> >> + USB_STS_TMODE_SEL(tmode - 1));
>> >
>> >I'm 90% sure this won't work. There's a reason why we only enter the
>> >requested test mode from status stage. How have you tested this?
>>
>
> What's the reason?
> It can work although the code is a little different with above, I
> tested it using USBxHSETT tool at Windows.

put a sniffer. Status stage won't complete

>> >> + irqreturn_t ret = IRQ_NONE;
>> >> + unsigned long flags;
>> >> + u32 reg;
>> >> +
>> >> + priv_dev = cdns->gadget_dev;
>> >> + spin_lock_irqsave(&priv_dev->lock, flags);
>> >
>> >you're already running in hardirq context. Why do you need this lock at
>> >all? I would be better to use the hardirq handler to mask your
>> >interrupts, so they don't fire again, then used the top-half (softirq)
>> >handler to actually handle the interrupts.
>>
>
> This controller may be ran at SMP environment, register and flag access
> needs to be protected among CPUs running.

in hardirq context? When interrupts are already disabled?

--
balbi

Attachments:

signature.asc (847.00 B)

2018-12-12 07:39:26

[permalink] [raw]

Subject: RE: [PATCH v1 2/2] usb:cdns3 Add Cadence USB3 DRD Driver

> >> >> + USB_CMD_STMODE |
> >> >> +
> >> >> + USB_STS_TMODE_SEL(tmode - 1));
> >> >
> >> >I'm 90% sure this won't work. There's a reason why we only enter the
> >> >requested test mode from status stage. How have you tested this?
> >>
> >
> > What's the reason?
> > It can work although the code is a little different with above, I
> > tested it using USBxHSETT tool at Windows.
>
> put a sniffer. Status stage won't complete
>

Ok, you mean sending test packet during the status completion handler?
I will see whether the status stage can complete next time when doing test.

> >> >> + irqreturn_t ret = IRQ_NONE;
> >> >> + unsigned long flags;
> >> >> + u32 reg;
> >> >> +
> >> >> + priv_dev = cdns->gadget_dev;
> >> >> + spin_lock_irqsave(&priv_dev->lock, flags);
> >> >
> >> >you're already running in hardirq context. Why do you need this lock
> >> >at all? I would be better to use the hardirq handler to mask your
> >> >interrupts, so they don't fire again, then used the top-half
> >> >(softirq) handler to actually handle the interrupts.
> >>
> >
> > This controller may be ran at SMP environment, register and flag
> > access needs to be protected among CPUs running.
>
> in hardirq context? When interrupts are already disabled?

Interrupt handler (hardirq context) at CPU0, and process at CPU1, eg role switch, unload module, etc.

Peter

2018-12-12 08:36:43

[permalink] [raw]

Subject: RE: [PATCH v1 2/2] usb:cdns3 Add Cadence USB3 DRD Driver

Peter Chen <[email protected]> writes:
>> >> >> + irqreturn_t ret = IRQ_NONE;
>> >> >> + unsigned long flags;
>> >> >> + u32 reg;
>> >> >> +
>> >> >> + priv_dev = cdns->gadget_dev;
>> >> >> + spin_lock_irqsave(&priv_dev->lock, flags);
>> >> >
>> >> >you're already running in hardirq context. Why do you need this lock
>> >> >at all? I would be better to use the hardirq handler to mask your
>> >> >interrupts, so they don't fire again, then used the top-half
>> >> >(softirq) handler to actually handle the interrupts.
>> >>
>> >
>> > This controller may be ran at SMP environment, register and flag
>> > access needs to be protected among CPUs running.
>>
>> in hardirq context? When interrupts are already disabled?
>
> Interrupt handler (hardirq context) at CPU0, and process at CPU1, eg
> role switch, unload module, etc.

the process at CPU1 would need to disable interrupts (spin_lock_irq() or
spin_lock_irqsave()), not the hardirq on CPU0 as that already runs with
interrrupts disabled.

https://www.kernel.org/doc/html/latest/kernel-hacking/locking.html#table-of-minimum-requirements

--
balbi

Attachments:

signature.asc (847.00 B)

2018-12-12 09:26:29

[permalink] [raw]

Subject: RE: [PATCH v1 2/2] usb:cdns3 Add Cadence USB3 DRD Driver

> >
> > Interrupt handler (hardirq context) at CPU0, and process at CPU1, eg
> > role switch, unload module, etc.
>
> the process at CPU1 would need to disable interrupts (spin_lock_irq() or
> spin_lock_irqsave()), not the hardirq on CPU0 as that already runs with interrrupts
> disabled.
>
> https://www.kernel.org/doc/html/latest/kernel-hacking/locking.html#table-of-
> minimum-requirements
>

I see, thanks.

Peter

2018-12-12 15:55:53

by Bin Liu

[permalink] [raw]

Subject: Re: [PATCH v1 2/2] usb:cdns3 Add Cadence USB3 DRD Driver

Peter,

On Wed, Dec 12, 2018 at 10:04:25AM +0800, Peter Chen wrote:

[snip]

> > >I strongly advise against using dev_dbg() for debugging. Even more so
> > >inside your IRQ handler.
>
> Felipe, I use Dynamic Debug for debugging, and show debug messages with
> "dmesg" after testing/debugging. I see dwc3 using trace, any benefits
> for switching
> to trace?

The benefits I see are

- *by default*, the debug log doesn't have to go through uart console,
which is slow.

I typically 'cat trace_pipe' from a telnet which is much faster then
uart. But Dynamic Debug log by default got printed on uart, I have to
set printk level to not print them, which is an extra step.

- tracepoint uses one place to decode the message vs DD has to repeat
the similar print statement in the code; and tracepoint decodes it
offline which reduce the kernel runtime overhead too.

- with tracepoint, it is easier to turn on debug for a specific group of
messages.

- you can adjust the ftrace buffer size at runtime. can we do that for
printk? I don't remember.

Regards,
-Bin.

2018-12-13 01:23:08

[permalink] [raw]

Subject: RE: [PATCH v1 2/2] usb:cdns3 Add Cadence USB3 DRD Driver

> >
> > Felipe, I use Dynamic Debug for debugging, and show debug messages
> > with "dmesg" after testing/debugging. I see dwc3 using trace, any
> > benefits for switching to trace?
>
> The benefits I see are
>

Thanks, bin.

> - *by default*, the debug log doesn't have to go through uart console,
> which is slow.
>
> I typically 'cat trace_pipe' from a telnet which is much faster then
> uart. But Dynamic Debug log by default got printed on uart, I have to
> set printk level to not print them, which is an extra step.
>

It depends on the rootfs's setting. By default, the debug message level should be off (
console level = 7)

> - tracepoint uses one place to decode the message vs DD has to repeat
> the similar print statement in the code; and tracepoint decodes it
> offline which reduce the kernel runtime overhead too.
>

offline? You mean when you run "cat trace_pipe"?

> - with tracepoint, it is easier to turn on debug for a specific group of
> messages.
>

The DD can, but we don't do it often.

https://www.kernel.org/doc/html/latest/admin-guide/dynamic-debug-howto.html?highlight=dynamic%20debug

> - you can adjust the ftrace buffer size at runtime. can we do that for
> printk? I don't remember.

It may can't. The log buf can only be changed by bootargs: log_buf_len

Peter

2018-12-13 09:23:36

[permalink] [raw]

Subject: Re: [PATCH v1 1/2] dt-bindings: add binding for USBSS-DRD controller.

On Tue, Dec 11, 2018 at 6:19 PM Roger Quadros <[email protected]> wrote:
>
> Pawel,
>
> On 10/12/18 14:39, Pawel Laszczak wrote:
> > This patch aim at documenting USB related dt-bindings for the
> > Cadence USBSS-DRD controller.
> >
> > Signed-off-by: Pawel Laszczak <[email protected]>
> > ---
> > .../devicetree/bindings/usb/cdns3-usb.txt | 31 +++++++++++++++++++
> > 1 file changed, 31 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/usb/cdns3-usb.txt
> >
> > diff --git a/Documentation/devicetree/bindings/usb/cdns3-usb.txt b/Documentation/devicetree/bindings/usb/cdns3-usb.txt
> > new file mode 100644
> > index 000000000000..ae4a255f0b10
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/usb/cdns3-usb.txt
> > @@ -0,0 +1,31 @@
> > +Binding for the Cadence USBSS-DRD controller
> > +
> > +Required properties:
> > + - reg: Physical base address and size of the controller's register areas.
> > + Controller has 3 different regions:
> > + region 1 - HOST registers area
> > + region 2 - DEVICE registers area
> > + region 3 - OTG/DRD registers area
> > + - compatible: Should contain: "cdns,usb3"
> > + - interrupts: Interrupt specifier. Refer to interrupt bindings.
> > + Driver supports only single interrupt line.
> > + This single interrupt is shared between Device,
> > + host and OTG/DRD part of driver.
> > +
> > +Optional propertiesi:
>
> s/propertiesi/properties
>
> > + - maximum-speed : valid arguments are "super-speed", "high-speed" and
> > + "full-speed"; refer to usb/generic.txt
> > + - dr_mode: Should be one of "host", "peripheral" or "otg".
> > + - phys: reference to the USB PHY
> > + - phy-names: name of the USB PHY, should be "cdns3,usbphy"
> > +
> > +
> > +Example:
> > + usb@f3000000 {
> > + compatible = "cdns,usb3";
> > + interrupts = <USB_IRQ 7 IRQ_TYPE_LEVEL_HIGH>;
> > + reg = <0xf3000000 0x10000 //memory area for HOST registers
> > + 0xf3010000 0x10000 //memory area for DEVICE registers
> > + 0xf3020000 0x10000>; //memory area for OTG/DRD registers
>
> Use "/* <comment> */" instead.
>
> > + };
> > +
> >

When running git am to apply patch, it has below warning, please fix them.

Applying: dt-bindings: add binding for USBSS-DRD controller.
.git/rebase-apply/patch:42: new blank line at EOF.
+
warning: 1 line adds whitespace errors.

2018-12-13 09:27:16

[permalink] [raw]

Subject: RE: [PATCH v1 1/2] dt-bindings: add binding for USBSS-DRD controller.

Hi,

>On Tue, Dec 11, 2018 at 6:19 PM Roger Quadros <[email protected]> wrote:
>>
>> Pawel,
>>
>> On 10/12/18 14:39, Pawel Laszczak wrote:
>> > This patch aim at documenting USB related dt-bindings for the
>> > Cadence USBSS-DRD controller.
>> >
>> > Signed-off-by: Pawel Laszczak <[email protected]>
>> > ---
>> > .../devicetree/bindings/usb/cdns3-usb.txt | 31 +++++++++++++++++++
>> > 1 file changed, 31 insertions(+)
>> > create mode 100644 Documentation/devicetree/bindings/usb/cdns3-usb.txt
>> >
>> > diff --git a/Documentation/devicetree/bindings/usb/cdns3-usb.txt b/Documentation/devicetree/bindings/usb/cdns3-usb.txt
>> > new file mode 100644
>> > index 000000000000..ae4a255f0b10
>> > --- /dev/null
>> > +++ b/Documentation/devicetree/bindings/usb/cdns3-usb.txt
>> > @@ -0,0 +1,31 @@
>> > +Binding for the Cadence USBSS-DRD controller
>> > +
>> > +Required properties:
>> > + - reg: Physical base address and size of the controller's register areas.
>> > + Controller has 3 different regions:
>> > + region 1 - HOST registers area
>> > + region 2 - DEVICE registers area
>> > + region 3 - OTG/DRD registers area
>> > + - compatible: Should contain: "cdns,usb3"
>> > + - interrupts: Interrupt specifier. Refer to interrupt bindings.
>> > + Driver supports only single interrupt line.
>> > + This single interrupt is shared between Device,
>> > + host and OTG/DRD part of driver.
>> > +
>> > +Optional propertiesi:
>>
>> s/propertiesi/properties
>>
>> > + - maximum-speed : valid arguments are "super-speed", "high-speed" and
>> > + "full-speed"; refer to usb/generic.txt
>> > + - dr_mode: Should be one of "host", "peripheral" or "otg".
>> > + - phys: reference to the USB PHY
>> > + - phy-names: name of the USB PHY, should be "cdns3,usbphy"
>> > +
>> > +
>> > +Example:
>> > + usb@f3000000 {
>> > + compatible = "cdns,usb3";
>> > + interrupts = <USB_IRQ 7 IRQ_TYPE_LEVEL_HIGH>;
>> > + reg = <0xf3000000 0x10000 //memory area for HOST registers
>> > + 0xf3010000 0x10000 //memory area for DEVICE registers
>> > + 0xf3020000 0x10000>; //memory area for OTG/DRD registers
>>
>> Use "/* <comment> */" instead.
>>
>> > + };
>> > +
>> >
>
>When running git am to apply patch, it has below warning, please fix them.
>
>Applying: dt-bindings: add binding for USBSS-DRD controller.
>.git/rebase-apply/patch:42: new blank line at EOF.
>+
>warning: 1 line adds whitespace errors.

Ok, thanks
Cheers
Pawel

2018-12-13 09:37:58

[permalink] [raw]

Subject: Re: [PATCH v1 2/2] usb:cdns3 Add Cadence USB3 DRD Driver

On Mon, Dec 10, 2018 at 8:55 PM Pawel Laszczak <[email protected]> wrote:
>
> This patch introduce new Cadence USBSS DRD driver
> to linux kernel.
>
> The Cadence USBSS DRD Driver is a highly
> configurable IP Core which can be
> instantiated as Dual-Role Device (DRD),
> Peripheral Only and Host Only (XHCI)
> configurations.
>
> The current driver has been validated with
> FPGA burned. We have support for PCIe
> bus, which is used on FPGA prototyping.
>
> The host side of USBSS-DRD controller is compliance
> with XHCI specification, so it works with
> standard XHCI linux driver.
>
> Signed-off-by: Pawel Laszczak <[email protected]>
> ---

I have compiled it at my ARM64 platform, and will give you more feedback after
adding platform support. Below is one compile warning, please fix

CC drivers/usb/cdns3/host.o
AR drivers/usb/cdns3/cdns3-pci.o
/home/b29397/work/projects/linux-imx/drivers/usb/cdns3/gadget.c: In
function ‘cdns3_gadget_ep_disable’:
/home/b29397/work/projects/linux-imx/drivers/usb/cdns3/gadget.c:1122:19:
warning: ‘priv_dev’ may be used uninitialized in this function
[-Wmaybe-uninitialized]
dev_dbg(priv_dev->dev, "usbss: invalid parameters\n");
^~
AR drivers/usb/cdns3/cdns3.o

Peter

> drivers/usb/Kconfig | 2 +
> drivers/usb/Makefile | 2 +
> drivers/usb/cdns3/Kconfig | 44 +
> drivers/usb/cdns3/Makefile | 16 +
> drivers/usb/cdns3/cdns3-pci-wrap.c | 157 +++
> drivers/usb/cdns3/core.c | 451 +++++++
> drivers/usb/cdns3/core.h | 108 ++
> drivers/usb/cdns3/debug.h | 346 ++++++
> drivers/usb/cdns3/debugfs.c | 168 +++
> drivers/usb/cdns3/drd.c | 315 +++++
> drivers/usb/cdns3/drd.h | 129 ++
> drivers/usb/cdns3/ep0.c | 864 +++++++++++++
> drivers/usb/cdns3/gadget-export.h | 28 +
> drivers/usb/cdns3/gadget.c | 1802 ++++++++++++++++++++++++++++
> drivers/usb/cdns3/gadget.h | 1177 ++++++++++++++++++
> drivers/usb/cdns3/host-export.h | 28 +
> drivers/usb/cdns3/host.c | 74 ++
> drivers/usb/cdns3/trace.c | 11 +
> drivers/usb/cdns3/trace.h | 343 ++++++
> 19 files changed, 6065 insertions(+)
> create mode 100644 drivers/usb/cdns3/Kconfig
> create mode 100644 drivers/usb/cdns3/Makefile
> create mode 100644 drivers/usb/cdns3/cdns3-pci-wrap.c
> create mode 100644 drivers/usb/cdns3/core.c
> create mode 100644 drivers/usb/cdns3/core.h
> create mode 100644 drivers/usb/cdns3/debug.h
> create mode 100644 drivers/usb/cdns3/debugfs.c
> create mode 100644 drivers/usb/cdns3/drd.c
> create mode 100644 drivers/usb/cdns3/drd.h
> create mode 100644 drivers/usb/cdns3/ep0.c
> create mode 100644 drivers/usb/cdns3/gadget-export.h
> create mode 100644 drivers/usb/cdns3/gadget.c
> create mode 100644 drivers/usb/cdns3/gadget.h
> create mode 100644 drivers/usb/cdns3/host-export.h
> create mode 100644 drivers/usb/cdns3/host.c
> create mode 100644 drivers/usb/cdns3/trace.c
> create mode 100644 drivers/usb/cdns3/trace.h
>
> diff --git a/drivers/usb/Kconfig b/drivers/usb/Kconfig
> index 987fc5ba6321..5f9334019d04 100644
> --- a/drivers/usb/Kconfig
> +++ b/drivers/usb/Kconfig
> @@ -112,6 +112,8 @@ source "drivers/usb/usbip/Kconfig"
>
> endif
>
> +source "drivers/usb/cdns3/Kconfig"
> +
> source "drivers/usb/mtu3/Kconfig"
>
> source "drivers/usb/musb/Kconfig"
> diff --git a/drivers/usb/Makefile b/drivers/usb/Makefile
> index 7d1b8c82b208..ab125b966cac 100644
> --- a/drivers/usb/Makefile
> +++ b/drivers/usb/Makefile
> @@ -12,6 +12,8 @@ obj-$(CONFIG_USB_DWC3) += dwc3/
> obj-$(CONFIG_USB_DWC2) += dwc2/
> obj-$(CONFIG_USB_ISP1760) += isp1760/
>
> +obj-$(CONFIG_USB_CDNS3) += cdns3/
> +
> obj-$(CONFIG_USB_MON) += mon/
> obj-$(CONFIG_USB_MTU3) += mtu3/
>
> diff --git a/drivers/usb/cdns3/Kconfig b/drivers/usb/cdns3/Kconfig
> new file mode 100644
> index 000000000000..4adfd87811e8
> --- /dev/null
> +++ b/drivers/usb/cdns3/Kconfig
> @@ -0,0 +1,44 @@
> +config USB_CDNS3
> + tristate "Cadence USB3 Dual-Role Controller"
> + depends on USB_SUPPORT && (USB || USB_GADGET) && HAS_DMA
> + help
> + Say Y here if your system has a cadence USB3 dual-role controller.
> + It supports: dual-role switch, Host-only, and Peripheral-only.
> +
> + If you choose to build this driver is a dynamically linked
> + module, the module will be called cdns3.ko.
> +
> +if USB_CDNS3
> +
> +config USB_CDNS3_GADGET
> + bool "Cadence USB3 device controller"
> + depends on USB_GADGET
> + help
> + Say Y here to enable device controller functionality of the
> + cadence USBSS-DEV driver.
> +
> + This controller supports FF, HS and SS mode. It doesn't support
> + LS and SSP mode
> +
> +config USB_CDNS3_HOST
> + bool "Cadence USB3 host controller"
> + depends on USB_XHCI_HCD
> + help
> + Say Y here to enable host controller functionality of the
> + cadence driver.
> +
> + Host controller is compliance with XHCI so it will use
> + standard XHCI driver.
> +
> +config USB_CDNS3_PCI_WRAP
> + tristate "Cadence USB3 support on PCIe-based platforms"
> + depends on USB_PCI && ACPI
> + default USB_CDNS3
> + help
> + If you're using the USBSS Core IP with a PCIe, please say
> + 'Y' or 'M' here.
> +
> + If you choose to build this driver as module it will
> + be dynamically linked and module will be called cdns3-pci.ko
> +
> +endif
> diff --git a/drivers/usb/cdns3/Makefile b/drivers/usb/cdns3/Makefile
> new file mode 100644
> index 000000000000..3f63baa24294
> --- /dev/null
> +++ b/drivers/usb/cdns3/Makefile
> @@ -0,0 +1,16 @@
> +# SPDX-License-Identifier: GPL-2.0
> +# define_trace.h needs to know how to find our header
> +CFLAGS_trace.o := -I$(src)
> +
> +obj-$(CONFIG_USB_CDNS3) += cdns3.o
> +obj-$(CONFIG_USB_CDNS3_PCI_WRAP) += cdns3-pci.o
> +
> +cdns3-y := core.o drd.o trace.o
> +
> +ifneq ($(CONFIG_DEBUG_FS),)
> + cdns3-y += debugfs.o
> +endif
> +
> +cdns3-$(CONFIG_USB_CDNS3_GADGET) += gadget.o ep0.o
> +cdns3-$(CONFIG_USB_CDNS3_HOST) += host.o
> +cdns3-pci-y := cdns3-pci-wrap.o
> diff --git a/drivers/usb/cdns3/cdns3-pci-wrap.c b/drivers/usb/cdns3/cdns3-pci-wrap.c
> new file mode 100644
> index 000000000000..e93179c45ece
> --- /dev/null
> +++ b/drivers/usb/cdns3/cdns3-pci-wrap.c
> @@ -0,0 +1,157 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Cadence USBSS PCI Glue driver
> + *
> + * Copyright (C) 2018 Cadence.
> + *
> + * Author: Pawel Laszczak <[email protected]>
> + */
> +
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/pci.h>
> +#include <linux/platform_device.h>
> +#include <linux/dma-mapping.h>
> +#include <linux/slab.h>
> +
> +struct cdns3_wrap {
> + struct platform_device *plat_dev;
> + struct pci_dev *hg_dev;
> + struct resource dev_res[4];
> +};
> +
> +struct cdns3_wrap wrap;
> +
> +#define RES_IRQ_ID 0
> +#define RES_HOST_ID 1
> +#define RES_DEV_ID 2
> +#define RES_DRD_ID 3
> +
> +#define PCI_BAR_HOST 0
> +#define PCI_BAR_DEV 2
> +#define PCI_BAR_OTG 4
> +
> +#define PCI_DEV_FN_HOST_DEVICE 0
> +#define PCI_DEV_FN_OTG 1
> +
> +#define PCI_DRIVER_NAME "cdns3-pci-usbss"
> +#define PLAT_DRIVER_NAME "cdns-usb3"
> +
> +#define CDNS_VENDOR_ID 0x17cd
> +#define CDNS_DEVICE_ID 0x0100
> +
> +/**
> + * cdns3_pci_probe - Probe function for Cadence USB wrapper driver
> + * @pdev: platform device object
> + * @id: pci device id
> + *
> + * Returns 0 on success otherwise negative errno
> + */
> +static int cdns3_pci_probe(struct pci_dev *pdev,
> + const struct pci_device_id *id)
> +{
> + struct platform_device_info plat_info;
> + struct cdns3_wrap *wrap;
> + struct resource *res;
> + int err;
> +
> + /*
> + * for GADGET/HOST PCI (devfn) function number is 0,
> + * for OTG PCI (devfn) function number is 1
> + */
> + if (!id || pdev->devfn != PCI_DEV_FN_HOST_DEVICE)
> + return -EINVAL;
> +
> + err = pcim_enable_device(pdev);
> + if (err) {
> + dev_err(&pdev->dev, "Enabling PCI device has failed %d\n", err);
> + return err;
> + }
> +
> + pci_set_master(pdev);
> + wrap = devm_kzalloc(&pdev->dev, sizeof(*wrap), GFP_KERNEL);
> + if (!wrap) {
> + dev_err(&pdev->dev, "Failed to allocate memory\n");
> + return -ENOMEM;
> + }
> +
> + /* function 0: host(BAR_0) + device(BAR_1) + otg(BAR_2)). */
> + memset(wrap->dev_res, 0x00,
> + sizeof(struct resource) * ARRAY_SIZE(wrap->dev_res));
> + dev_dbg(&pdev->dev, "Initialize Device resources\n");
> + res = wrap->dev_res;
> +
> + res[RES_DEV_ID].start = pci_resource_start(pdev, PCI_BAR_DEV);
> + res[RES_DEV_ID].end = pci_resource_end(pdev, PCI_BAR_DEV);
> + res[RES_DEV_ID].name = "cdns3-dev-regs";
> + res[RES_DEV_ID].flags = IORESOURCE_MEM;
> + dev_dbg(&pdev->dev, "USBSS-DEV physical base addr: %pa\n",
> + &res[RES_DEV_ID].start);
> +
> + res[RES_HOST_ID].start = pci_resource_start(pdev, PCI_BAR_HOST);
> + res[RES_HOST_ID].end = pci_resource_end(pdev, PCI_BAR_HOST);
> + res[RES_HOST_ID].name = "cdns3-xhci-regs";
> + res[RES_HOST_ID].flags = IORESOURCE_MEM;
> + dev_dbg(&pdev->dev, "USBSS-XHCI physical base addr: %pa\n",
> + &res[RES_HOST_ID].start);
> +
> + res[RES_DRD_ID].start = pci_resource_start(pdev, PCI_BAR_OTG);
> + res[RES_DRD_ID].end = pci_resource_end(pdev, PCI_BAR_OTG);
> + res[RES_DRD_ID].name = "cdns3-otg";
> + res[RES_DRD_ID].flags = IORESOURCE_MEM;
> + dev_dbg(&pdev->dev, "USBSS-DRD physical base addr: %pa\n",
> + &res[RES_DRD_ID].start);
> +
> + /* Interrupt common for both device and XHCI */
> + wrap->dev_res[RES_IRQ_ID].start = pdev->irq;
> + wrap->dev_res[RES_IRQ_ID].name = "cdns3-irq";
> + wrap->dev_res[RES_IRQ_ID].flags = IORESOURCE_IRQ;
> +
> + /* set up platform device info */
> + memset(&plat_info, 0, sizeof(plat_info));
> + plat_info.parent = &pdev->dev;
> + plat_info.fwnode = pdev->dev.fwnode;
> + plat_info.name = PLAT_DRIVER_NAME;
> + plat_info.id = pdev->devfn;
> + plat_info.res = wrap->dev_res;
> + plat_info.num_res = ARRAY_SIZE(wrap->dev_res);
> + plat_info.dma_mask = pdev->dma_mask;
> +
> + /* register platform device */
> + wrap->plat_dev = platform_device_register_full(&plat_info);
> + if (IS_ERR(wrap->plat_dev)) {
> + err = PTR_ERR(wrap->plat_dev);
> + return err;
> + }
> +
> + pci_set_drvdata(pdev, wrap);
> +
> + return err;
> +}
> +
> +void cdns3_pci_remove(struct pci_dev *pdev)
> +{
> + struct cdns3_wrap *wrap = (struct cdns3_wrap *)pci_get_drvdata(pdev);
> +
> + platform_device_unregister(wrap->plat_dev);
> +}
> +
> +static const struct pci_device_id cdns3_pci_ids[] = {
> + { PCI_DEVICE(CDNS_VENDOR_ID, CDNS_DEVICE_ID), },
> + { 0, }
> +};
> +
> +static struct pci_driver cdns3_pci_driver = {
> + .name = PCI_DRIVER_NAME,
> + .id_table = cdns3_pci_ids,
> + .probe = cdns3_pci_probe,
> + .remove = cdns3_pci_remove,
> +};
> +
> +module_pci_driver(cdns3_pci_driver);
> +MODULE_DEVICE_TABLE(pci, cdns3_pci_ids);
> +
> +MODULE_AUTHOR("Pawel Laszczak <[email protected]>");
> +MODULE_LICENSE("GPL v2");
> +MODULE_DESCRIPTION("Cadence USBSS PCI wrapperr");
> +
> diff --git a/drivers/usb/cdns3/core.c b/drivers/usb/cdns3/core.c
> new file mode 100644
> index 000000000000..b93e3788bd33
> --- /dev/null
> +++ b/drivers/usb/cdns3/core.c
> @@ -0,0 +1,451 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Cadence USBSS DRD Driver.
> + *
> + * Copyright (C) 2018 Cadence.
> + * Copyright (C) 2017-2018 NXP
> + *
> + * Author: Peter Chen <[email protected]>
> + * Pawel Laszczak <[email protected]>
> + */
> +
> +#include <linux/module.h>
> +#include <linux/kernel.h>
> +#include <linux/platform_device.h>
> +#include <linux/interrupt.h>
> +#include <linux/io.h>
> +#include <linux/pm_runtime.h>
> +
> +#include "gadget.h"
> +#include "core.h"
> +#include "host-export.h"
> +#include "gadget-export.h"
> +#include "drd.h"
> +#include "debug.h"
> +
> +static inline
> +struct cdns3_role_driver *cdns3_get_current_role_driver(struct cdns3 *cdns)
> +{
> + WARN_ON(cdns->role >= CDNS3_ROLE_END || !cdns->roles[cdns->role]);
> + return cdns->roles[cdns->role];
> +}
> +
> +static inline int cdns3_role_start(struct cdns3 *cdns, enum cdns3_roles role)
> +{
> + int ret;
> +
> + if (WARN_ON(role >= CDNS3_ROLE_END))
> + return 0;
> +
> + if (!cdns->roles[role])
> + return -ENXIO;
> +
> + if (cdns->roles[role]->state == CDNS3_ROLE_STATE_ACTIVE)
> + return 0;
> +
> + mutex_lock(&cdns->mutex);
> + cdns->role = role;
> + ret = cdns->roles[role]->start(cdns);
> + if (!ret)
> + cdns->roles[role]->state = CDNS3_ROLE_STATE_ACTIVE;
> + mutex_unlock(&cdns->mutex);
> + return ret;
> +}
> +
> +void cdns3_role_stop(struct cdns3 *cdns)
> +{
> + enum cdns3_roles role = cdns->role;
> +
> + if (role >= CDNS3_ROLE_END) {
> + WARN_ON(role > CDNS3_ROLE_END);
> + return;
> + }
> +
> + if (cdns->roles[role]->state == CDNS3_ROLE_STATE_INACTIVE)
> + return;
> +
> + mutex_lock(&cdns->mutex);
> + cdns->roles[role]->stop(cdns);
> + cdns->roles[role]->state = CDNS3_ROLE_STATE_INACTIVE;
> + mutex_unlock(&cdns->mutex);
> +}
> +
> +/*
> + * cdns->role gets from cdns3_get_initial_role, and this API tells role at the
> + * runtime.
> + * If both roles are supported, the role is selected based on vbus/id.
> + * It could be read from OTG register or external connector.
> + * If only single role is supported, only one role structure
> + * is allocated, cdns->roles[CDNS3_ROLE_HOST] or cdns->roles[CDNS3_ROLE_GADGET].
> + */
> +static enum cdns3_roles cdns3_get_initial_role(struct cdns3 *cdns)
> +{
> + if (cdns->roles[CDNS3_ROLE_HOST] && cdns->roles[CDNS3_ROLE_GADGET]) {
> + if (cdns3_is_host(cdns))
> + return CDNS3_ROLE_HOST;
> + if (cdns3_is_device(cdns))
> + return CDNS3_ROLE_GADGET;
> + }
> + return cdns->roles[CDNS3_ROLE_HOST]
> + ? CDNS3_ROLE_HOST
> + : CDNS3_ROLE_GADGET;
> +}
> +
> +static void cdns3_exit_roles(struct cdns3 *cdns)
> +{
> + cdns3_role_stop(cdns);
> + cdns3_drd_exit(cdns);
> +}
> +
> +/**
> + * cdns3_core_init_role - initialize role of operation
> + * @cdns: Pointer to cdns3 structure
> + *
> + * Returns 0 on success otherwise negative errno
> + */
> +static int cdns3_core_init_role(struct cdns3 *cdns)
> +{
> + struct device *dev = cdns->dev;
> + enum usb_dr_mode best_dr_mode;
> + enum usb_dr_mode dr_mode;
> + int ret = 0;
> +
> + dr_mode = usb_get_dr_mode(dev);
> + cdns->role = CDNS3_ROLE_END;
> +
> + /*
> + * If driver can't read mode by means of usb_get_dr_mdoe function then
> + * chooses mode according with Kernel configuration. This setting
> + * can be restricted later depending on strap pin configuration.
> + */
> + if (dr_mode == USB_DR_MODE_UNKNOWN) {
> + if (IS_ENABLED(CONFIG_USB_CDNS3_HOST) &&
> + IS_ENABLED(CONFIG_USB_CDNS3_GADGET))
> + dr_mode = USB_DR_MODE_OTG;
> + else if (IS_ENABLED(CONFIG_USB_CDNS3_HOST))
> + dr_mode = USB_DR_MODE_HOST;
> + else if (IS_ENABLED(CONFIG_USB_CDNS3_GADGET))
> + dr_mode = USB_DR_MODE_PERIPHERAL;
> + }
> +
> + best_dr_mode = USB_DR_MODE_OTG;
> +
> + if (dr_mode == USB_DR_MODE_OTG) {
> + best_dr_mode = cdns->dr_mode;
> + } else if (cdns->dr_mode == USB_DR_MODE_OTG) {
> + best_dr_mode = dr_mode;
> + } else if (cdns->dr_mode != dr_mode) {
> + dev_err(dev, "Incorrect DRD configuration\n");
> + return -EINVAL;
> + }
> +
> + dr_mode = best_dr_mode;
> +
> + if (dr_mode == USB_DR_MODE_OTG || dr_mode == USB_DR_MODE_HOST) {
> + ret = cdns3_host_init(cdns);
> + if (ret) {
> + dev_err(dev, "Host initialization failed with %d\n",
> + ret);
> + goto err;
> + }
> + }
> +
> + if (dr_mode == USB_DR_MODE_OTG || dr_mode == USB_DR_MODE_PERIPHERAL) {
> + ret = cdns3_gadget_init(cdns);
> + if (ret) {
> + dev_err(dev, "Device initialization failed with %d\n",
> + ret);
> + goto err;
> + }
> + }
> +
> + cdns->desired_dr_mode = dr_mode;
> + cdns->dr_mode = dr_mode;
> + /*
> + * dr_mode could be change so DRD must update controller
> + * configuration
> + */
> + ret = cdns3_drd_update_mode(cdns);
> +
> + cdns->role = cdns3_get_initial_role(cdns);
> +
> + ret = cdns3_role_start(cdns, cdns->role);
> + if (ret) {
> + dev_err(dev, "can't start %s role\n",
> + cdns3_get_current_role_driver(cdns)->name);
> + goto err;
> + }
> +
> + return ret;
> +err:
> + cdns3_exit_roles(cdns);
> + return ret;
> +}
> +
> +/**
> + * cdsn3_get_real_role - get real role of controller based on hardware settings.
> + * @cdns: Pointer to cdns3 structure
> + *
> + * Returns role
> + */
> +enum cdns3_roles cdsn3_get_real_role(struct cdns3 *cdns)
> +{
> + enum cdns3_roles role = CDNS3_ROLE_END;
> +
> + if (cdns->current_dr_mode == USB_DR_MODE_OTG) {
> + if (cdns3_get_id(cdns))
> + role = CDNS3_ROLE_GADGET;
> + else
> + role = CDNS3_ROLE_HOST;
> + } else {
> + if (cdns3_is_host(cdns))
> + role = CDNS3_ROLE_HOST;
> + if (cdns3_is_device(cdns))
> + role = CDNS3_ROLE_GADGET;
> + }
> +
> + return role;
> +}
> +
> +/**
> + * cdns3_role_switch - work queue handler for role switch
> + *
> + * @work: work queue item structure
> + *
> + * Handles below events:
> + * - Role switch for dual-role devices
> + * - CDNS3_ROLE_GADGET <--> CDNS3_ROLE_END for peripheral-only devices
> + */
> +static void cdns3_role_switch(struct work_struct *work)
> +{
> + enum cdns3_roles role = CDNS3_ROLE_END;
> + struct cdns3_role_driver *role_drv;
> + enum cdns3_roles current_role;
> + struct cdns3 *cdns;
> + int ret = 0;
> +
> + cdns = container_of(work, struct cdns3, role_switch_wq);
> +
> + /* During switching cdns->role can be different then role */
> + role = cdsn3_get_real_role(cdns);
> +
> + role_drv = cdns3_get_current_role_driver(cdns);
> +
> + pm_runtime_get_sync(cdns->dev);
> +
> + /* Disable current role. This state can be forced from user space. */
> + if (cdns->debug_disable && role_drv->state == CDNS3_ROLE_STATE_ACTIVE) {
> + cdns3_role_stop(cdns);
> + goto exit;
> + }
> +
> + /* Do nothing if nothing changed */
> + if (cdns->role == role && role_drv->state == CDNS3_ROLE_STATE_ACTIVE)
> + goto exit;
> +
> + cdns3_role_stop(cdns);
> +
> + role = cdsn3_get_real_role(cdns);
> +
> + current_role = cdns->role;
> + dev_dbg(cdns->dev, "Switching role");
> +
> + ret = cdns3_role_start(cdns, role);
> +
> + if (ret) {
> + /* Back to current role */
> + dev_err(cdns->dev, "set %d has failed, back to %d\n",
> + role, current_role);
> + cdns3_role_start(cdns, current_role);
> + }
> +exit:
> + pm_runtime_put_sync(cdns->dev);
> +}
> +
> +/**
> + * cdns3_probe - probe for cdns3 core device
> + * @pdev: Pointer to cdns3 core platform device
> + *
> + * Returns 0 on success otherwise negative errno
> + */
> +static int cdns3_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct resource *res;
> + struct cdns3 *cdns;
> + void __iomem *regs;
> + int ret;
> +
> + cdns = devm_kzalloc(dev, sizeof(*cdns), GFP_KERNEL);
> + if (!cdns)
> + return -ENOMEM;
> +
> + cdns->dev = dev;
> +
> + platform_set_drvdata(pdev, cdns);
> +
> + res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
> + if (!res) {
> + dev_err(dev, "missing IRQ\n");
> + return -ENODEV;
> + }
> + cdns->irq = res->start;
> +
> + cdns->xhci_res[0] = *res;
> +
> + /*
> + * Request memory region
> + * region-0: xHCI
> + * region-1: Peripheral
> + * region-2: OTG registers
> + */
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + cdns->xhci_res[1] = *res;
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
> + regs = devm_ioremap_resource(dev, res);
> + if (IS_ERR(regs))
> + return PTR_ERR(regs);
> + cdns->dev_regs = regs;
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
> + regs = devm_ioremap_resource(dev, res);
> + if (IS_ERR(regs))
> + return PTR_ERR(regs);
> + cdns->otg_regs = regs;
> +
> + mutex_init(&cdns->mutex);
> +
> + cdns->phy = devm_phy_get(dev, "cdns3,usbphy");
> + if (IS_ERR(cdns->phy)) {
> + ret = PTR_ERR(cdns->phy);
> + if (ret == -ENOSYS || ret == -ENODEV) {
> + cdns->phy = NULL;
> + } else if (ret == -EPROBE_DEFER) {
> + return ret;
> + } else {
> + dev_err(dev, "no phy found\n");
> + goto err0;
> + }
> + }
> +
> + phy_init(cdns->phy);
> +
> + INIT_WORK(&cdns->role_switch_wq, cdns3_role_switch);
> +
> + ret = cdns3_drd_init(cdns);
> + if (ret)
> + goto err1;
> +
> + ret = cdns3_core_init_role(cdns);
> + if (ret)
> + goto err1;
> +
> + cdns3_debugfs_init(cdns);
> + device_set_wakeup_capable(dev, true);
> + pm_runtime_set_active(dev);
> + pm_runtime_enable(dev);
> +
> + /*
> + * The controller needs less time between bus and controller suspend,
> + * and we also needs a small delay to avoid frequently entering low
> + * power mode.
> + */
> + pm_runtime_set_autosuspend_delay(dev, 20);
> + pm_runtime_mark_last_busy(dev);
> + pm_runtime_use_autosuspend(dev);
> + dev_dbg(dev, "Cadence USB3 core: probe succeed\n");
> +
> + return 0;
> +
> +err1:
> + phy_exit(cdns->phy);
> +err0:
> + return ret;
> +}
> +
> +/**
> + * cdns3_remove - unbind drd driver and clean up
> + * @pdev: Pointer to Linux platform device
> + *
> + * Returns 0 on success otherwise negative errno
> + */
> +static int cdns3_remove(struct platform_device *pdev)
> +{
> + struct cdns3 *cdns = platform_get_drvdata(pdev);
> +
> + pm_runtime_get_sync(&pdev->dev);
> + pm_runtime_disable(&pdev->dev);
> + pm_runtime_put_noidle(&pdev->dev);
> + cdns3_debugfs_exit(cdns);
> + cdns3_exit_roles(cdns);
> + phy_exit(cdns->phy);
> + return 0;
> +}
> +
> +#ifdef CONFIG_OF
> +static const struct of_device_id of_cdns3_match[] = {
> + { .compatible = "cdns,usb3" },
> + { },
> +};
> +MODULE_DEVICE_TABLE(of, of_cdns3_match);
> +#endif
> +
> +#ifdef CONFIG_PM
> +
> +#ifdef CONFIG_PM_SLEEP
> +static int cdns3_suspend(struct device *dev)
> +{
> + /* TODO: Implements this function. */
> + return 0;
> +}
> +
> +static int cdns3_resume(struct device *dev)
> +{
> + /* TODO: Implements this function. */
> + return 0;
> +}
> +#endif /* CONFIG_PM_SLEEP */
> +static int cdns3_runtime_suspend(struct device *dev)
> +{ /* TODO: Implements this function. */
> + return 0;
> +}
> +
> +static int cdns3_runtime_resume(struct device *dev)
> +{
> + /* TODO: Implements this function. */
> + return 0;
> +}
> +#endif /* CONFIG_PM */
> +
> +static const struct dev_pm_ops cdns3_pm_ops = {
> + SET_SYSTEM_SLEEP_PM_OPS(cdns3_suspend, cdns3_resume)
> + SET_RUNTIME_PM_OPS(cdns3_runtime_suspend, cdns3_runtime_resume, NULL)
> +};
> +
> +static struct platform_driver cdns3_driver = {
> + .probe = cdns3_probe,
> + .remove = cdns3_remove,
> + .driver = {
> + .name = "cdns-usb3",
> + .of_match_table = of_match_ptr(of_cdns3_match),
> + .pm = &cdns3_pm_ops,
> + },
> +};
> +
> +static int __init cdns3_driver_platform_register(void)
> +{
> + return platform_driver_register(&cdns3_driver);
> +}
> +module_init(cdns3_driver_platform_register);
> +
> +static void __exit cdns3_driver_platform_unregister(void)
> +{
> + platform_driver_unregister(&cdns3_driver);
> +}
> +module_exit(cdns3_driver_platform_unregister);
> +
> +MODULE_ALIAS("platform:cdns3");
> +MODULE_AUTHOR("Pawel Laszczak <[email protected]>");
> +MODULE_LICENSE("GPL v2");
> +MODULE_DESCRIPTION("Cadence USB3 DRD Controller Driver");
> diff --git a/drivers/usb/cdns3/core.h b/drivers/usb/cdns3/core.h
> new file mode 100644
> index 000000000000..ffd1971ff893
> --- /dev/null
> +++ b/drivers/usb/cdns3/core.h
> @@ -0,0 +1,108 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * Cadence USBSS DRD Header File.
> + *
> + * Copyright (C) 2017-2018 NXP
> + * Copyright (C) 2018 Cadence.
> + *
> + * Authors: Peter Chen <[email protected]>
> + * Pawel Laszczak <[email protected]>
> + */
> +#include <linux/usb/otg.h>
> +
> +#ifndef __LINUX_CDNS3_CORE_H
> +#define __LINUX_CDNS3_CORE_H
> +
> +struct cdns3;
> +enum cdns3_roles {
> + CDNS3_ROLE_HOST = 0,
> + CDNS3_ROLE_GADGET,
> + CDNS3_ROLE_END,
> +};
> +
> +/**
> + * struct cdns3_role_driver - host/gadget role driver
> + * @start: start this role
> + * @stop: stop this role
> + * @suspend: suspend callback for this role
> + * @resume: resume callback for this role
> + * @irq: irq handler for this role
> + * @name: role name string (host/gadget)
> + * @state: current state
> + */
> +struct cdns3_role_driver {
> + int (*start)(struct cdns3 *cdns);
> + void (*stop)(struct cdns3 *cdns);
> + int (*suspend)(struct cdns3 *cdns, bool do_wakeup);
> + int (*resume)(struct cdns3 *cdns, bool hibernated);
> + const char *name;
> +#define CDNS3_ROLE_STATE_INACTIVE 0
> +#define CDNS3_ROLE_STATE_ACTIVE 1
> + int state;
> +};
> +
> +#define CDNS3_XHCI_RESOURCES_NUM 2
> +/**
> + * struct cdns3 - Representation of Cadence USB3 DRD controller.
> + * @dev: pointer to Cadence device struct
> + * @xhci_regs: pointer to base of xhci registers
> + * @xhci_res: the resource for xhci
> + * @dev_regs: pointer to base of dev registers
> + * @otg_regs: pointer to base of otg registers
> + * @irq: irq number for controller
> + * @roles: array of supported roles for this controller
> + * @role: current role
> + * @host_dev: the child host device pointer for cdns3 core
> + * @gadget_dev: the child gadget device pointer for cdns3 core
> + * @usb: phy for this controller
> + * @role_switch_wq: work queue item for role switch
> + * @in_lpm: the controller in low power mode
> + * @wakeup_int: the wakeup interrupt
> + * @mutex: the mutex for concurrent code at driver
> + * @dr_mode: supported mode of operation it can be only Host, only Device
> + * or OTG mode that allow to switch between Device and Host mode.
> + * This field based on firmware setting, kernel configuration
> + * and hardware configuration.
> + * @current_dr_mode: current mode of operation when in dual-role mode
> + * @desired_dr_mode: desired mode of operation when in dual-role mode.
> + * This value can be changed during runtime.
> + * Available options depends on dr_mode:
> + * dr_mode | desired_dr_mode and current_dr_mode
> + * ----------------------------------------------------------------
> + * USB_DR_MODE_HOST | only USB_DR_MODE_HOST
> + * USB_DR_MODE_PERIPHERAL | only USB_DR_MODE_PERIPHERAL
> + * USB_DR_MODE_OTG | only USB_DR_MODE_HOST
> + * USB_DR_MODE_OTG | only USB_DR_MODE_PERIPHERAL
> + * USB_DR_MODE_OTG | USB_DR_MODE_OTG
> + *
> + * Desired_dr_role can be changed by means of debugfs.
> + * @root: debugfs root folder pointer
> + * @debug_disable:
> + */
> +struct cdns3 {
> + struct device *dev;
> + void __iomem *xhci_regs;
> + struct resource xhci_res[CDNS3_XHCI_RESOURCES_NUM];
> + struct cdns3_usb_regs __iomem *dev_regs;
> + struct cdns3_otg_regs *otg_regs;
> + int irq;
> + struct cdns3_role_driver *roles[CDNS3_ROLE_END];
> + enum cdns3_roles role;
> + struct platform_device *host_dev;
> + struct cdns3_device *gadget_dev;
> + struct phy *phy;
> + struct work_struct role_switch_wq;
> + int in_lpm:1;
> + int wakeup_int:1;
> + /* mutext used in workqueue*/
> + struct mutex mutex;
> + enum usb_dr_mode dr_mode;
> + enum usb_dr_mode current_dr_mode;
> + enum usb_dr_mode desired_dr_mode;
> + struct dentry *root;
> + int debug_disable:1;
> +};
> +
> +void cdns3_role_stop(struct cdns3 *cdns);
> +
> +#endif /* __LINUX_CDNS3_CORE_H */
> diff --git a/drivers/usb/cdns3/debug.h b/drivers/usb/cdns3/debug.h
> new file mode 100644
> index 000000000000..afb81d224718
> --- /dev/null
> +++ b/drivers/usb/cdns3/debug.h
> @@ -0,0 +1,346 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * Cadence USBSS DRD Driver.
> + * Debug header file.
> + *
> + * Copyright (C) 2018 Cadence.
> + *
> + * Author: Pawel Laszczak <[email protected]>
> + */
> +#ifndef __LINUX_CDNS3_DEBUG
> +#define __LINUX_CDNS3_DEBUG
> +#include "gadget.h"
> +
> +static inline void cdns3_decode_get_status(u8 bRequestType, u16 wIndex,
> + u16 wLength, char *str)
> +{
> + switch (bRequestType & USB_RECIP_MASK) {
> + case USB_RECIP_INTERFACE:
> + sprintf(str, "Get Interface Status Intf = %d, L: = %d",
> + wIndex, wLength);
> + break;
> + case USB_RECIP_ENDPOINT:
> + sprintf(str, "Get Endpoint Status ep%d%s",
> + wIndex & ~USB_DIR_IN,
> + wIndex & USB_DIR_IN ? "in" : "out");
> + break;
> + }
> +}
> +
> +static inline const char *cdns3_decode_device_feature(u16 wValue)
> +{
> + switch (wValue) {
> + case USB_DEVICE_SELF_POWERED:
> + return "Self Powered";
> + case USB_DEVICE_REMOTE_WAKEUP:
> + return "Remote Wakeup";
> + case USB_DEVICE_TEST_MODE:
> + return "Test Mode";
> + case USB_DEVICE_U1_ENABLE:
> + return "U1 Enable";
> + case USB_DEVICE_U2_ENABLE:
> + return "U2 Enable";
> + case USB_DEVICE_LTM_ENABLE:
> + return "LTM Enable";
> + default:
> + return "UNKNOWN";
> + }
> +}
> +
> +static inline const char *cdns3_decode_test_mode(u16 wIndex)
> +{
> + switch (wIndex) {
> + case TEST_J:
> + return ": TEST_J";
> + case TEST_K:
> + return ": TEST_K";
> + case TEST_SE0_NAK:
> + return ": TEST_SE0_NAK";
> + case TEST_PACKET:
> + return ": TEST_PACKET";
> + case TEST_FORCE_EN:
> + return ": TEST_FORCE_EN";
> + default:
> + return ": UNKNOWN";
> + }
> +}
> +
> +static inline void cdns3_decode_set_clear_feature(u8 bRequestType, u8 bRequest,
> + u16 wValue, u16 wIndex,
> + char *str)
> +{
> + switch (bRequestType & USB_RECIP_MASK) {
> + case USB_RECIP_DEVICE:
> + sprintf(str, "%s Device Feature(%s%s)",
> + bRequest == USB_REQ_CLEAR_FEATURE ? "Clear" : "Set",
> + cdns3_decode_device_feature(wValue),
> + wValue == USB_DEVICE_TEST_MODE ?
> + cdns3_decode_test_mode(wIndex) : "");
> + break;
> + case USB_RECIP_INTERFACE:
> + sprintf(str, "%s Interface Feature(%s)",
> + bRequest == USB_REQ_CLEAR_FEATURE ? "Clear" : "Set",
> + wIndex == USB_INTRF_FUNC_SUSPEND ?
> + "Function Suspend" : "UNKNOWN");
> + break;
> + case USB_RECIP_ENDPOINT:
> + sprintf(str, "%s Endpoint Feature(%s ep%d%s)",
> + bRequest == USB_REQ_CLEAR_FEATURE ? "Clear" : "Set",
> + wIndex == USB_ENDPOINT_HALT ? "Halt" : "UNKNOWN",
> + wIndex & ~USB_DIR_IN,
> + wIndex & USB_DIR_IN ? "in" : "out");
> + break;
> + }
> +}
> +
> +static inline const char *cdns3_decode_descriptor(u16 wValue)
> +{
> + switch (wValue >> 8) {
> + case USB_DT_DEVICE:
> + return "Device";
> + case USB_DT_CONFIG:
> + return "Configuration";
> + case USB_DT_STRING:
> + return "String";
> + case USB_DT_INTERFACE:
> + return "Interface";
> + case USB_DT_ENDPOINT:
> + return "Endpoint";
> + case USB_DT_DEVICE_QUALIFIER:
> + return "Device Qualifier";
> + case USB_DT_OTHER_SPEED_CONFIG:
> + return "Other Speed Config";
> + case USB_DT_INTERFACE_POWER:
> + return "Interface Power";
> + case USB_DT_OTG:
> + return "OTG";
> + case USB_DT_DEBUG:
> + return "Debug";
> + case USB_DT_INTERFACE_ASSOCIATION:
> + return "Interface Association";
> + case USB_DT_BOS:
> + return "BOS";
> + case USB_DT_DEVICE_CAPABILITY:
> + return "Device Capability";
> + case USB_DT_SS_ENDPOINT_COMP:
> + return "SS Endpoint Companion";
> + case USB_DT_SSP_ISOC_ENDPOINT_COMP:
> + return "SSP Isochronous Endpoint Companion";
> + default:
> + return "UNKNOWN";
> + }
> +}
> +
> +/**
> + * cdns3_decode_ctrl - returns a string represetion of ctrl request
> + */
> +static inline const char *cdns3_decode_ctrl(char *str, u8 bRequestType,
> + u8 bRequest, u16 wValue,
> + u16 wIndex, u16 wLength)
> +{
> + switch (bRequest) {
> + case USB_REQ_GET_STATUS:
> + cdns3_decode_get_status(bRequestType, wIndex,
> + wLength, str);
> + break;
> + case USB_REQ_CLEAR_FEATURE:
> + case USB_REQ_SET_FEATURE:
> + cdns3_decode_set_clear_feature(bRequestType, bRequest,
> + wValue, wIndex, str);
> + break;
> + case USB_REQ_SET_ADDRESS:
> + sprintf(str, "Set Address Addr: %02x", wValue);
> + break;
> + case USB_REQ_GET_DESCRIPTOR:
> + sprintf(str, "GET %s Descriptor I: %d, L: %d",
> + cdns3_decode_descriptor(wValue),
> + wValue & 0xff, wLength);
> + break;
> + case USB_REQ_SET_DESCRIPTOR:
> + sprintf(str, "SET %s Descriptor I: %d, L: %d",
> + cdns3_decode_descriptor(wValue),
> + wValue & 0xff, wLength);
> + break;
> + case USB_REQ_GET_CONFIGURATION:
> + sprintf(str, "Get Configuration L: %d", wLength);
> + break;
> + case USB_REQ_SET_CONFIGURATION:
> + sprintf(str, "Set Configuration Config: %d ", wValue);
> + break;
> + case USB_REQ_GET_INTERFACE:
> + sprintf(str, "Get Interface Intf: %d, L: %d", wIndex, wLength);
> + break;
> + case USB_REQ_SET_INTERFACE:
> + sprintf(str, "Set Interface Intf: %d, Alt: %d", wIndex, wValue);
> + break;
> + case USB_REQ_SYNCH_FRAME:
> + sprintf(str, "Synch Frame Ep: %d, L: %d", wIndex, wLength);
> + break;
> + case USB_REQ_SET_SEL:
> + sprintf(str, "Set SEL L: %d", wLength);
> + break;
> + case USB_REQ_SET_ISOCH_DELAY:
> + sprintf(str, "Set Isochronous Delay Delay: %d ns", wValue);
> + break;
> + default:
> + sprintf(str,
> + "SETUP BRT: %02x BR: %02x V: %04x I: %04x L: %04x\n",
> + bRequestType, bRequest,
> + wValue, wIndex, wLength);
> + }
> +
> + return str;
> +}
> +
> +static inline char *cdns3_decode_usb_irq(struct cdns3_device *priv_dev,
> + u32 usb_ists)
> +{
> + static char str[256];
> + int ret;
> +
> + ret = sprintf(str, "IRQ %08x = ", usb_ists);
> +
> + if (usb_ists & (USB_ISTS_CON2I | USB_ISTS_CONI)) {
> + u32 speed = cdns3_get_speed(priv_dev);
> +
> + ret += sprintf(str + ret, "Connection %s\n",
> + usb_speed_string(speed));
> + }
> + if (usb_ists & USB_ISTS_CON2I || usb_ists & USB_ISTS_CONI)
> + ret += sprintf(str + ret, "Disconnection ");
> + if (usb_ists & USB_ISTS_L2ENTI)
> + ret += sprintf(str + ret, "suspended ");
> +
> + if (usb_ists & USB_ISTS_L2EXTI)
> + ret += sprintf(str + ret, "L2 exit ");
> + if (usb_ists & USB_ISTS_U3EXTI)
> + ret += sprintf(str + ret, "U3 exit ");
> + if (usb_ists & USB_ISTS_UWRESI)
> + ret += sprintf(str + ret, "Warm Reset ");
> + if (usb_ists & USB_ISTS_UHRESI)
> + ret += sprintf(str + ret, "Hot Reset ");
> + if (usb_ists & USB_ISTS_U2RESI)
> + ret += sprintf(str + ret, "Reset");
> +
> + return str;
> +}
> +
> +static inline char *cdns3_decode_ep_irq(u32 ep_sts, const char *ep_name)
> +{
> + static char str[256];
> + int ret;
> +
> + ret = sprintf(str, "IRQ for %s: %08x ", ep_name, ep_sts);
> +
> + if (ep_sts & EP_STS_SETUP)
> + ret += sprintf(str + ret, "SETUP ");
> + if (ep_sts & EP_STS_IOC)
> + ret += sprintf(str + ret, "IOC ");
> + if (ep_sts & EP_STS_ISP)
> + ret += sprintf(str + ret, "ISP ");
> + if (ep_sts & EP_STS_DESCMIS)
> + ret += sprintf(str + ret, "DESCMIS ");
> + if (ep_sts & EP_STS_STREAMR)
> + ret += sprintf(str + ret, "STREAMR ");
> + if (ep_sts & EP_STS_MD_EXIT)
> + ret += sprintf(str + ret, "MD_EXIT ");
> + if (ep_sts & EP_STS_TRBERR)
> + ret += sprintf(str + ret, "TRBERR ");
> + if (ep_sts & EP_STS_NRDY)
> + ret += sprintf(str + ret, "NRDY ");
> + if (ep_sts & EP_STS_PRIME)
> + ret += sprintf(str + ret, "PRIME ");
> + if (ep_sts & EP_STS_SIDERR)
> + ret += sprintf(str + ret, "SIDERRT ");
> + if (ep_sts & EP_STS_OUTSMM)
> + ret += sprintf(str + ret, "OUTSMM ");
> + if (ep_sts & EP_STS_ISOERR)
> + ret += sprintf(str + ret, "ISOERR ");
> + if (ep_sts & EP_STS_IOT)
> + ret += sprintf(str + ret, "IOT ");
> +
> + return str;
> +}
> +
> +static inline char *cdns3_decode_epx_irq(struct cdns3_endpoint *priv_ep)
> +{
> + struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
> +
> + return cdns3_decode_ep_irq(readl(&priv_dev->regs->ep_sts),
> + priv_ep->name);
> +}
> +
> +static inline char *cdns3_decode_ep0_irq(struct cdns3_device *priv_dev)
> +{
> + if (priv_dev->ep0_data_dir)
> + return cdns3_decode_ep_irq(readl(&priv_dev->regs->ep_sts),
> + "ep0IN");
> + else
> + return cdns3_decode_ep_irq(readl(&priv_dev->regs->ep_sts),
> + "ep0OUT");
> +}
> +
> +/**
> + * Debug a transfer ring.
> + *
> + * Prints out all TRBs in the endpoint ring, even those after the Link TRB.
> + *.
> + */
> +static inline char *cdns3_dbg_ring(struct cdns3_endpoint *priv_ep,
> + int free_trbs, u8 pcs, u8 ccs,
> + int enqueue, int dequeue,
> + struct cdns3_trb *ring, char *str)
> +{
> + u64 addr = priv_ep->trb_pool_dma;
> + struct cdns3_trb *trb;
> + int ret = 0;
> + int i;
> +
> + trb = &ring[priv_ep->dequeue];
> + ret += sprintf(str + ret, "\n\t\tRing contents for %s:", priv_ep->name);
> +
> + ret += sprintf(str + ret,
> + "\n\t\tRing deq index: %d, trb: %p (virt), 0x%llx (dma)\n",
> + dequeue, trb,
> + (unsigned long long)cdns3_trb_virt_to_dma(priv_ep, trb));
> +
> + trb = &ring[priv_ep->enqueue];
> + ret += sprintf(str + ret,
> + "\t\tRing enq index: %d, trb: %p (virt), 0x%llx (dma)\n",
> + enqueue, trb,
> + (unsigned long long)cdns3_trb_virt_to_dma(priv_ep, trb));
> +
> + ret += sprintf(str + ret,
> + "\t\tfree trbs: %d, CCS=%d, PCS=%d\n", free_trbs, ccs,
> + pcs);
> +
> + if (TRBS_PER_SEGMENT > 64) {
> + sprintf(str + ret, "\t\tTo big transfer ring %d\n",
> + TRBS_PER_SEGMENT);
> + return str;
> + }
> +
> + for (i = 0; i < TRBS_PER_SEGMENT; ++i) {
> + trb = &ring[i];
> + ret += sprintf(str + ret,
> + "\t\t@%016llx %08x %08x %08x\n", addr,
> + le32_to_cpu(trb->buffer),
> + le32_to_cpu(trb->length),
> + le32_to_cpu(trb->control));
> + addr += sizeof(*trb);
> + }
> +
> + return str;
> +}
> +
> +#ifdef CONFIG_DEBUG_FS
> +void cdns3_debugfs_init(struct cdns3 *cdns);
> +void cdns3_debugfs_exit(struct cdns3 *cdns);
> +#else
> +void cdns3_debugfs_init(struct cdns3 *cdns);
> +{ }
> +void cdns3_debugfs_exit(struct cdns3 *cdns);
> +{ }
> +#endif
> +
> +#endif /*__LINUX_CDNS3_DEBUG*/
> diff --git a/drivers/usb/cdns3/debugfs.c b/drivers/usb/cdns3/debugfs.c
> new file mode 100644
> index 000000000000..d7919f5c1d90
> --- /dev/null
> +++ b/drivers/usb/cdns3/debugfs.c
> @@ -0,0 +1,168 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Cadence USBSS DRD Controller DebugFS filer.
> + *
> + * Copyright (C) 2018 Cadence.
> + *
> + * Author: Pawel Laszczak <[email protected]>
> + */
> +
> +#include <linux/types.h>
> +#include <linux/debugfs.h>
> +#include <linux/seq_file.h>
> +#include <linux/uaccess.h>
> +
> +#include "core.h"
> +#include "gadget.h"
> +#include "drd.h"
> +
> +static int cdns3_mode_show(struct seq_file *s, void *unused)
> +{
> + struct cdns3 *cdns = s->private;
> +
> + switch (cdns->current_dr_mode) {
> + case USB_DR_MODE_HOST:
> + seq_puts(s, "host\n");
> + break;
> + case USB_DR_MODE_PERIPHERAL:
> + seq_puts(s, "device\n");
> + break;
> + case USB_DR_MODE_OTG:
> + seq_puts(s, "otg\n");
> + break;
> + default:
> + seq_puts(s, "UNKNOWN mode\n");
> + }
> +
> + return 0;
> +}
> +
> +static int cdns3_mode_open(struct inode *inode, struct file *file)
> +{
> + return single_open(file, cdns3_mode_show, inode->i_private);
> +}
> +
> +static ssize_t cdns3_mode_write(struct file *file,
> + const char __user *ubuf,
> + size_t count, loff_t *ppos)
> +{
> + struct seq_file *s = file->private_data;
> + struct cdns3 *cdns = s->private;
> + u32 mode = USB_DR_MODE_UNKNOWN;
> + char buf[32];
> +
> + if (copy_from_user(&buf, ubuf, min_t(size_t, sizeof(buf) - 1, count)))
> + return -EFAULT;
> +
> + if (!strncmp(buf, "host", 4)) {
> + if (cdns->dr_mode == USB_DR_MODE_HOST ||
> + cdns->dr_mode == USB_DR_MODE_OTG) {
> + mode = USB_DR_MODE_HOST;
> + }
> + }
> +
> + if (!strncmp(buf, "device", 6))
> + if (cdns->dr_mode == USB_DR_MODE_PERIPHERAL ||
> + cdns->dr_mode == USB_DR_MODE_OTG)
> + mode = USB_DR_MODE_PERIPHERAL;
> +
> + if (!strncmp(buf, "otg", 3) && cdns->dr_mode == USB_DR_MODE_OTG)
> + mode = USB_DR_MODE_OTG;
> +
> + if (mode == USB_DR_MODE_UNKNOWN) {
> + dev_err(cdns->dev, "Failed: incorrect mode setting\n");
> + return -EFAULT;
> + }
> +
> + if (cdns->current_dr_mode != mode) {
> + cdns->desired_dr_mode = mode;
> + cdns->debug_disable = 0;
> + cdns3_role_stop(cdns);
> + cdns3_drd_update_mode(cdns);
> + queue_work(system_freezable_wq, &cdns->role_switch_wq);
> + }
> +
> + return count;
> +}
> +
> +static const struct file_operations cdns3_mode_fops = {
> + .open = cdns3_mode_open,
> + .write = cdns3_mode_write,
> + .read = seq_read,
> + .llseek = seq_lseek,
> + .release = single_release,
> +};
> +
> +static int cdns3_disable_show(struct seq_file *s, void *unused)
> +{
> + struct cdns3 *cdns = s->private;
> +
> + if (!cdns->debug_disable)
> + seq_puts(s, "0\n");
> + else
> + seq_puts(s, "1\n");
> +
> + return 0;
> +}
> +
> +static ssize_t cdns3_disable_write(struct file *file,
> + const char __user *ubuf,
> + size_t count, loff_t *ppos)
> +{
> + struct seq_file *s = file->private_data;
> + struct cdns3 *cdns = s->private;
> + int disable;
> + char buf[32];
> +
> + if (copy_from_user(&buf, ubuf, min_t(size_t, sizeof(buf) - 1, count)))
> + return -EFAULT;
> +
> + if (!strncmp(buf, "1", 1) || !strncmp(buf, "yes", 3)) {
> + disable = 1;
> + } else if (!strncmp(buf, "0", 1) || !strncmp(buf, "no", 2)) {
> + disable = 0;
> + } else {
> + dev_err(cdns->dev, "Failed: incorrect disable setting\n");
> + return -EFAULT;
> + }
> +
> + if (disable != cdns->debug_disable) {
> + cdns->debug_disable = disable;
> + queue_work(system_freezable_wq, &cdns->role_switch_wq);
> + }
> +
> + return count;
> +}
> +
> +static int cdns3_disable_open(struct inode *inode, struct file *file)
> +{
> + return single_open(file, cdns3_disable_show, inode->i_private);
> +}
> +
> +static const struct file_operations cdns3_disable_fops = {
> + .open = cdns3_disable_open,
> + .write = cdns3_disable_write,
> + .read = seq_read,
> + .llseek = seq_lseek,
> + .release = single_release,
> +};
> +
> +void cdns3_debugfs_init(struct cdns3 *cdns)
> +{
> + struct dentry *root;
> +
> + root = debugfs_create_dir(dev_name(cdns->dev), NULL);
> + cdns->root = root;
> + if (IS_ENABLED(CONFIG_USB_CDNS3_GADGET) &&
> + IS_ENABLED(CONFIG_USB_CDNS3_HOST))
> + debugfs_create_file("mode", 0644, root, cdns,
> + &cdns3_mode_fops);
> +
> + debugfs_create_file("disable", 0644, root, cdns,
> + &cdns3_disable_fops);
> +}
> +
> +void cdns3_debugfs_exit(struct cdns3 *cdns)
> +{
> + debugfs_remove_recursive(cdns->root);
> +}
> diff --git a/drivers/usb/cdns3/drd.c b/drivers/usb/cdns3/drd.c
> new file mode 100644
> index 000000000000..45573427ba83
> --- /dev/null
> +++ b/drivers/usb/cdns3/drd.c
> @@ -0,0 +1,315 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Cadence USBSS DRD Driver.
> + *
> + * Copyright (C) 2018 Cadence.
> + *
> + * Author: Pawel Laszczak <[email protected]
> + *
> + */
> +#include <linux/kernel.h>
> +#include <linux/interrupt.h>
> +#include <linux/delay.h>
> +#include <linux/usb/otg.h>
> +
> +#include "gadget.h"
> +#include "drd.h"
> +#include "core.h"
> +
> +static int cdns3_drd_switch_gadget(struct cdns3 *cdns, int on);
> +static int cdns3_drd_switch_host(struct cdns3 *cdns, int on);
> +
> +/**
> + * cdns3_set_mode - change mode of OTG Core
> + * @cdns: pointer to context structure
> + * @mode: selected mode from cdns_role
> + */
> +void cdns3_set_mode(struct cdns3 *cdns, enum usb_dr_mode mode)
> +{
> + u32 reg;
> +
> + cdns->current_dr_mode = mode;
> +
> + switch (mode) {
> + case USB_DR_MODE_PERIPHERAL:
> + dev_info(cdns->dev, "Set controller to Gadget mode\n");
> + cdns3_drd_switch_gadget(cdns, 1);
> + break;
> + case USB_DR_MODE_HOST:
> + dev_info(cdns->dev, "Set controller to Host mode\n");
> + cdns3_drd_switch_host(cdns, 1);
> + break;
> + case USB_DR_MODE_OTG:
> + dev_info(cdns->dev, "Set controller to OTG mode\n");
> + reg = readl(&cdns->otg_regs->override);
> + reg |= OVERRIDE_IDPULLUP;
> + writel(reg, &cdns->otg_regs->override);
> +
> + /*
> + * Hardware specification says: "ID_VALUE must be valid within
> + * 50ms after idpullup is set to '1" so driver must wait
> + * 50ms before reading this pin.
> + */
> + usleep_range(50000, 60000);
> + break;
> + default:
> + cdns->current_dr_mode = USB_DR_MODE_UNKNOWN;
> + dev_err(cdns->dev, "Unsupported mode of operation %d\n", mode);
> + return;
> + }
> +}
> +
> +int cdns3_get_id(struct cdns3 *cdns)
> +{
> + int id;
> +
> + id = readl(&cdns->otg_regs->sts) & OTGSTS_ID_VALUE;
> + dev_dbg(cdns->dev, "OTG ID: %d", id);
> + return id;
> +}
> +
> +int cdns3_is_host(struct cdns3 *cdns)
> +{
> + if (cdns->current_dr_mode == USB_DR_MODE_HOST)
> + return 1;
> + else if (!cdns3_get_id(cdns))
> + return 1;
> +
> + return 0;
> +}
> +
> +int cdns3_is_device(struct cdns3 *cdns)
> +{
> + if (cdns->current_dr_mode == USB_DR_MODE_PERIPHERAL)
> + return 1;
> + else if (cdns->current_dr_mode == USB_DR_MODE_OTG)
> + if (cdns3_get_id(cdns))
> + return 1;
> +
> + return 0;
> +}
> +
> +/**
> + * cdns3_otg_disable_irq - Disable all OTG interrupts
> + * @cdns: Pointer to controller context structure
> + */
> +static void cdns3_otg_disable_irq(struct cdns3 *cdns)
> +{
> + writel(0, &cdns->otg_regs->ien);
> +}
> +
> +/**
> + * cdns3_otg_enable_irq - enable id and sess_valid interrupts
> + * @cdns: Pointer to controller context structure
> + */
> +static void cdns3_otg_enable_irq(struct cdns3 *cdns)
> +{
> + writel(OTGIEN_ID_CHANGE_INT | OTGIEN_VBUSVALID_RISE_INT |
> + OTGIEN_VBUSVALID_FALL_INT, &cdns->otg_regs->ien);
> +}
> +
> +/**
> + * cdns3_drd_switch_host - start/stop host
> + * @cdns: Pointer to controller context structure
> + * @on: 1 for start, 0 for stop
> + *
> + * Returns 0 on success otherwise negative errno
> + */
> +static int cdns3_drd_switch_host(struct cdns3 *cdns, int on)
> +{
> + int ret;
> + u32 reg = OTGCMD_OTG_DIS;
> +
> + /* switch OTG core */
> + if (on) {
> + writel(OTGCMD_HOST_BUS_REQ | reg, &cdns->otg_regs->cmd);
> +
> + dev_dbg(cdns->dev, "Waiting for Host mode is turned on\n");
> + ret = cdns3_handshake(&cdns->otg_regs->sts, OTGSTS_XHCI_READY,
> + OTGSTS_XHCI_READY, 100000);
> +
> + if (ret)
> + return ret;
> + } else {
> + usleep_range(30, 40);
> + writel(OTGCMD_HOST_BUS_DROP | OTGCMD_DEV_BUS_DROP |
> + OTGCMD_DEV_POWER_OFF | OTGCMD_HOST_POWER_OFF,
> + &cdns->otg_regs->cmd);
> + }
> +
> + return 0;
> +}
> +
> +/**
> + * cdns3_drd_switch_gadget - start/stop gadget
> + * @cdns: Pointer to controller context structure
> + * @on: 1 for start, 0 for stop
> + *
> + * Returns 0 on success otherwise negative errno
> + */
> +static int cdns3_drd_switch_gadget(struct cdns3 *cdns, int on)
> +{
> + int ret;
> + u32 reg = OTGCMD_OTG_DIS;
> +
> + /* switch OTG core */
> + if (on) {
> + writel(OTGCMD_DEV_BUS_REQ | reg, &cdns->otg_regs->cmd);
> +
> + dev_dbg(cdns->dev, "Waiting for Device mode is turned on\n");
> +
> + ret = cdns3_handshake(&cdns->otg_regs->sts, OTGSTS_DEV_READY,
> + OTGSTS_DEV_READY, 100000);
> +
> + if (ret)
> + return ret;
> + } else {
> + /*
> + * driver should wait at least 10us after disabling Device
> + * before turning-off Device (DEV_BUS_DROP)
> + */
> + usleep_range(20, 30);
> + writel(OTGCMD_HOST_BUS_DROP | OTGCMD_DEV_BUS_DROP |
> + OTGCMD_DEV_POWER_OFF | OTGCMD_HOST_POWER_OFF,
> + &cdns->otg_regs->cmd);
> + }
> +
> + return 0;
> +}
> +
> +/**
> + * cdns3_init_otg_mode - initialize drd controller
> + * @cdns: Pointer to controller context structure
> + *
> + * Returns 0 on success otherwise negative errno
> + */
> +static void cdns3_init_otg_mode(struct cdns3 *cdns)
> +{
> + cdns3_otg_disable_irq(cdns);
> + /* clear all interrupts */
> + writel(~0, &cdns->otg_regs->ivect);
> +
> + cdns3_set_mode(cdns, USB_DR_MODE_OTG);
> +
> + if (cdns3_is_host(cdns))
> + cdns3_drd_switch_host(cdns, 1);
> + else
> + cdns3_drd_switch_gadget(cdns, 1);
> +
> + cdns3_otg_enable_irq(cdns);
> +}
> +
> +/**
> + * cdns3_drd_update_mode - initialize mode of operation
> + * @cdns: Pointer to controller context structure
> + *
> + * Returns 0 on success otherwise negative errno
> + */
> +int cdns3_drd_update_mode(struct cdns3 *cdns)
> +{
> + int ret = 0;
> +
> + if (cdns->desired_dr_mode == cdns->current_dr_mode)
> + return ret;
> +
> + cdns3_drd_switch_gadget(cdns, 0);
> + cdns3_drd_switch_host(cdns, 0);
> +
> + switch (cdns->desired_dr_mode) {
> + case USB_DR_MODE_PERIPHERAL:
> + cdns3_set_mode(cdns, USB_DR_MODE_PERIPHERAL);
> + break;
> + case USB_DR_MODE_HOST:
> + cdns3_set_mode(cdns, USB_DR_MODE_HOST);
> + break;
> + case USB_DR_MODE_OTG:
> + cdns3_init_otg_mode(cdns);
> + break;
> + default:
> + dev_err(cdns->dev, "Unsupported mode of operation %d\n",
> + cdns->dr_mode);
> + return -EINVAL;
> + }
> +
> + return ret;
> +}
> +
> +/**
> + * cdns3_drd_irq - interrupt handler for OTG events
> + *
> + * @irq: irq number for cdns3 core device
> + * @data: structure of cdns3
> + *
> + * Returns IRQ_HANDLED or IRQ_NONE
> + */
> +static irqreturn_t cdns3_drd_irq(int irq, void *data)
> +{
> + irqreturn_t ret = IRQ_NONE;
> + struct cdns3 *cdns = data;
> + u32 reg;
> +
> + if (cdns->dr_mode != USB_DR_MODE_OTG)
> + return ret;
> +
> + reg = readl(&cdns->otg_regs->ivect);
> + if (!reg)
> + return ret;
> +
> + if (reg & OTGIEN_ID_CHANGE_INT) {
> + dev_dbg(cdns->dev, "OTG IRQ: new ID: %d\n",
> + cdns3_get_id(cdns));
> +
> + queue_work(system_freezable_wq, &cdns->role_switch_wq);
> +
> + ret = IRQ_HANDLED;
> + }
> +
> + writel(~0, &cdns->otg_regs->ivect);
> + return ret;
> +}
> +
> +int cdns3_drd_init(struct cdns3 *cdns)
> +{
> + int ret = 0;
> + u32 state;
> +
> + state = OTGSTS_STRAP(readl(&cdns->otg_regs->sts));
> +
> + /* Update dr_mode according to STRAP configuration. */
> + cdns->dr_mode = USB_DR_MODE_OTG;
> + if (state == OTGSTS_STRAP_HOST) {
> + dev_info(cdns->dev, "Controller strapped to HOST\n");
> + cdns->dr_mode = USB_DR_MODE_HOST;
> + } else if (state == OTGSTS_STRAP_GADGET) {
> + dev_info(cdns->dev, "Controller strapped to PERIPHERAL\n");
> + cdns->dr_mode = USB_DR_MODE_PERIPHERAL;
> + }
> +
> + cdns->desired_dr_mode = cdns->dr_mode;
> + cdns->current_dr_mode = USB_DR_MODE_UNKNOWN;
> +
> + ret = devm_request_irq(cdns->dev, cdns->irq, cdns3_drd_irq, IRQF_SHARED,
> + dev_name(cdns->dev), cdns);
> +
> + if (ret)
> + return ret;
> +
> + state = readl(&cdns->otg_regs->sts);
> + if (OTGSTS_OTG_NRDY(state) != 0) {
> + dev_err(cdns->dev, "Cadence USB3 OTG device not ready\n");
> + return -ENODEV;
> + }
> +
> + ret = cdns3_drd_update_mode(cdns);
> +
> + dev_info(cdns->dev, "Controller Device ID: %08lx, Revision ID: %08lx\n",
> + CDNS_RID(readl(&cdns->otg_regs->rid)),
> + CDNS_DID(readl(&cdns->otg_regs->did)));
> +
> + return ret;
> +}
> +
> +int cdns3_drd_exit(struct cdns3 *cdns)
> +{
> + return cdns3_drd_switch_host(cdns, 0);
> +}
> diff --git a/drivers/usb/cdns3/drd.h b/drivers/usb/cdns3/drd.h
> new file mode 100644
> index 000000000000..4159e6e612ac
> --- /dev/null
> +++ b/drivers/usb/cdns3/drd.h
> @@ -0,0 +1,129 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * Cadence USB3 DRD header file.
> + *
> + * Copyright (C) 2018 Cadence.
> + *
> + * Author: Pawel Laszczak <[email protected]>
> + */
> +#ifndef __LINUX_CDNS3_DRD
> +#define __LINUX_CDNS3_DRD
> +
> +#include <linux/usb/otg.h>
> +#include <linux/phy/phy.h>
> +#include "core.h"
> +
> +/* DRD register interface. */
> +struct cdns3_otg_regs {
> + __le32 did;
> + __le32 rid;
> + __le32 capabilities;
> + __le32 reserved1;
> + __le32 cmd;
> + __le32 sts;
> + __le32 state;
> + __le32 reserved2;
> + __le32 ien;
> + __le32 ivect;
> + __le32 refclk;
> + __le32 tmr;
> + __le32 reserved3[4];
> + __le32 simulate;
> + __le32 override;
> + __le32 susp_ctrl;
> + __le32 reserved4;
> + __le32 anasts;
> + __le32 adp_ramp_time;
> + __le32 ctrl1;
> + __le32 ctrl2;
> +};
> +
> +/* CDNS_RID - bitmasks */
> +#define CDNS_RID(p) ((p) & GENMASK(15, 0))
> +
> +/* CDNS_VID - bitmasks */
> +#define CDNS_DID(p) ((p) & GENMASK(31, 0))
> +
> +/* OTGCMD - bitmasks */
> +/* "Request the bus for Device mode. */
> +#define OTGCMD_DEV_BUS_REQ BIT(0)
> +/* Request the bus for Host mode */
> +#define OTGCMD_HOST_BUS_REQ BIT(1)
> +/* Enable OTG mode. */
> +#define OTGCMD_OTG_EN BIT(2)
> +/* Disable OTG mode */
> +#define OTGCMD_OTG_DIS BIT(3)
> +/*"Configure OTG as A-Device. */
> +#define OTGCMD_A_DEV_EN BIT(4)
> +/*"Configure OTG as A-Device. */
> +#define OTGCMD_A_DEV_DIS BIT(5)
> +/* Drop the bus for Device mod e. */
> +#define OTGCMD_DEV_BUS_DROP BIT(8)
> +/* Drop the bus for Host mode*/
> +#define OTGCMD_HOST_BUS_DROP BIT(9)
> +/* Power Down USBSS-DEV. */
> +#define OTGCMD_DEV_POWER_OFF BIT(11)
> +/* Power Down CDNSXHCI. */
> +#define OTGCMD_HOST_POWER_OFF BIT(12)
> +
> +/* OTGIEN - bitmasks */
> +/* ID change interrupt enable */
> +#define OTGIEN_ID_CHANGE_INT BIT(0)
> +/* Vbusvalid fall detected interrupt enable.*/
> +#define OTGIEN_VBUSVALID_RISE_INT BIT(4)
> +/* Vbusvalid fall detected interrupt enable */
> +#define OTGIEN_VBUSVALID_FALL_INT BIT(5)
> +
> +/* OTGSTS - bitmasks */
> +/*
> + * Current value of the ID pin. It is only valid when idpullup in
> + * OTGCTRL1_TYPE register is set to '1'.
> + */
> +#define OTGSTS_ID_VALUE BIT(0)
> +/* Current value of the vbus_valid */
> +#define OTGSTS_VBUS_VALID BIT(1)
> +/* Current value of the b_sess_vld */
> +#define OTGSTS_SESSION_VALID BIT(2)
> +/*Device mode is active*/
> +#define OTGSTS_DEV_ACTIVE BIT(3)
> +/* Host mode is active. */
> +#define OTGSTS_HOST_ACTIVE BIT(4)
> +/* OTG Controller not ready. */
> +#define OTGSTS_OTG_NRDY_MASK BIT(11)
> +#define OTGSTS_OTG_NRDY(p) ((p) & OTGSTS_OTG_NRDY_MASK)
> +/*
> + * Value of the strap pins.
> + * 000 - no default configuration
> + * 010 - Controller initiall configured as Host
> + * 100 - Controller initially configured as Device
> + */
> +#define OTGSTS_STRAP(p) (((p) & GENMASK(14, 12)) >> 12)
> +#define OTGSTS_STRAP_NO_DEFAULT_CFG 0x00
> +#define OTGSTS_STRAP_HOST_OTG 0x01
> +#define OTGSTS_STRAP_HOST 0x02
> +#define OTGSTS_STRAP_GADGET 0x04
> +/* Host mode is turned on. */
> +#define OTGSTS_XHCI_READY BIT(26)
> +/* "Device mode is turned on .*/
> +#define OTGSTS_DEV_READY BIT(27)
> +
> +/* OTGSTATE- bitmasks */
> +#define OTGSTATE_HOST_STATE_MASK GENMASK(5, 3)
> +#define OTGSTATE_HOST_STATE_IDLE 0x0
> +#define OTGSTATE_HOST_STATE_VBUS_FALL 0x7
> +#define OTGSTATE_HOST_STATE(p) (((p) & OTGSTATE_HOST_STATE_MASK) >> 3)
> +
> +/* OTGREFCLK - bitmasks */
> +#define OTGREFCLK_STB_CLK_SWITCH_EN BIT(31)
> +
> +/* OVERRIDE - bitmasks */
> +#define OVERRIDE_IDPULLUP BIT(0)
> +
> +int cdns3_is_host(struct cdns3 *cdns);
> +int cdns3_is_device(struct cdns3 *cdns);
> +int cdns3_get_id(struct cdns3 *cdns);
> +int cdns3_drd_init(struct cdns3 *cdns);
> +int cdns3_drd_exit(struct cdns3 *cdns);
> +int cdns3_drd_update_mode(struct cdns3 *cdns);
> +
> +#endif /* __LINUX_CDNS3_DRD */
> diff --git a/drivers/usb/cdns3/ep0.c b/drivers/usb/cdns3/ep0.c
> new file mode 100644
> index 000000000000..1ef0e9f73e3e
> --- /dev/null
> +++ b/drivers/usb/cdns3/ep0.c
> @@ -0,0 +1,864 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Cadence USBSS DRD Driver - gadget side.
> + *
> + * Copyright (C) 2018 Cadence Design Systems.
> + * Copyright (C) 2017-2018 NXP
> + *
> + * Authors: Pawel Jez <[email protected]>,
> + * Pawel Laszczak <[email protected]>
> + * Peter Chen <[email protected]>
> + */
> +
> +#include <linux/usb/composite.h>
> +
> +#include "gadget.h"
> +#include "trace.h"
> +
> +static struct usb_endpoint_descriptor cdns3_gadget_ep0_desc = {
> + .bLength = USB_DT_ENDPOINT_SIZE,
> + .bDescriptorType = USB_DT_ENDPOINT,
> + .bmAttributes = USB_ENDPOINT_XFER_CONTROL,
> +};
> +
> +/**
> + * cdns3_ep0_run_transfer - Do transfer on default endpoint hardware
> + * @priv_dev: extended gadget object
> + * @dma_addr: physical address where data is/will be stored
> + * @length: data length
> + * @erdy: set it to 1 when ERDY packet should be sent -
> + * exit from flow control state
> + */
> +static void cdns3_ep0_run_transfer(struct cdns3_device *priv_dev,
> + dma_addr_t dma_addr,
> + unsigned int length, int erdy)
> +{
> + struct cdns3_usb_regs __iomem *regs = priv_dev->regs;
> + struct cdns3_endpoint *priv_ep = ep_to_cdns3_ep(priv_dev->gadget.ep0);
> +
> + priv_dev->ep0_trb->buffer = TRB_BUFFER(dma_addr);
> + priv_dev->ep0_trb->length = TRB_LEN(length);
> + priv_dev->ep0_trb->control = TRB_CYCLE | TRB_IOC | TRB_TYPE(TRB_NORMAL);
> +
> + trace_cdns3_prepare_trb(priv_ep, priv_dev->ep0_trb);
> +
> + cdns3_select_ep(priv_dev, priv_dev->ep0_data_dir);
> +
> + writel(EP_STS_TRBERR, &regs->ep_sts);
> + writel(EP_TRADDR_TRADDR(priv_dev->ep0_trb_dma), &regs->ep_traddr);
> + trace_cdns3_doorbell_ep0(priv_dev->ep0_data_dir ? "ep0in" : "ep0out");
> +
> + /* TRB should be prepared before starting transfer */
> + writel(EP_CMD_DRDY, &regs->ep_cmd);
> +
> + if (erdy)
> + writel(EP_CMD_ERDY, &priv_dev->regs->ep_cmd);
> +}
> +
> +/**
> + * cdns3_ep0_delegate_req - Returns status of handling setup packet
> + * Setup is handled by gadget driver
> + * @priv_dev: extended gadget object
> + * @ctrl_req: pointer to received setup packet
> + *
> + * Returns zero on success or negative value on failure
> + */
> +static int cdns3_ep0_delegate_req(struct cdns3_device *priv_dev,
> + struct usb_ctrlrequest *ctrl_req)
> +{
> + int ret;
> +
> + spin_unlock(&priv_dev->lock);
> + priv_dev->setup_pending = 1;
> + ret = priv_dev->gadget_driver->setup(&priv_dev->gadget, ctrl_req);
> + priv_dev->setup_pending = 0;
> + spin_lock(&priv_dev->lock);
> + return ret;
> +}
> +
> +static void cdns3_prepare_setup_packet(struct cdns3_device *priv_dev)
> +{
> + priv_dev->ep0_data_dir = 0;
> + cdns3_ep0_run_transfer(priv_dev, priv_dev->setup_dma,
> + sizeof(struct usb_ctrlrequest), 0);
> +}
> +
> +/**
> + * cdns3_req_ep0_set_configuration - Handling of SET_CONFIG standard USB request
> + * @priv_dev: extended gadget object
> + * @ctrl_req: pointer to received setup packet
> + *
> + * Returns 0 if success, USB_GADGET_DELAYED_STATUS on deferred status stage,
> + * error code on error
> + */
> +static int cdns3_req_ep0_set_configuration(struct cdns3_device *priv_dev,
> + struct usb_ctrlrequest *ctrl_req)
> +{
> + enum usb_device_state device_state = priv_dev->gadget.state;
> + struct cdns3_endpoint *priv_ep;
> + u32 config = le16_to_cpu(ctrl_req->wValue);
> + int result = 0;
> + int i;
> +
> + switch (device_state) {
> + case USB_STATE_ADDRESS:
> + /* Configure non-control EPs */
> + for (i = 0; i < CDNS3_ENDPOINTS_MAX_COUNT; i++) {
> + priv_ep = priv_dev->eps[i];
> + if (!priv_ep)
> + continue;
> +
> + if (priv_ep->flags & EP_CLAIMED)
> + cdns3_ep_config(priv_ep);
> + }
> +
> + result = cdns3_ep0_delegate_req(priv_dev, ctrl_req);
> +
> + if (result)
> + return result;
> +
> + if (config) {
> + cdns3_set_hw_configuration(priv_dev);
> + } else {
> + cdns3_gadget_unconfig(priv_dev);
> + usb_gadget_set_state(&priv_dev->gadget,
> + USB_STATE_ADDRESS);
> + }
> + break;
> + case USB_STATE_CONFIGURED:
> + result = cdns3_ep0_delegate_req(priv_dev, ctrl_req);
> +
> + if (!config && !result) {
> + cdns3_gadget_unconfig(priv_dev);
> + usb_gadget_set_state(&priv_dev->gadget,
> + USB_STATE_ADDRESS);
> + }
> + break;
> + default:
> + result = -EINVAL;
> + }
> +
> + return result;
> +}
> +
> +/**
> + * cdns3_req_ep0_set_address - Handling of SET_ADDRESS standard USB request
> + * @priv_dev: extended gadget object
> + * @ctrl_req: pointer to received setup packet
> + *
> + * Returns 0 if success, error code on error
> + */
> +static int cdns3_req_ep0_set_address(struct cdns3_device *priv_dev,
> + struct usb_ctrlrequest *ctrl_req)
> +{
> + enum usb_device_state device_state = priv_dev->gadget.state;
> + u32 reg;
> + u32 addr;
> +
> + addr = le16_to_cpu(ctrl_req->wValue);
> +
> + if (addr > USB_DEVICE_MAX_ADDRESS) {
> + dev_err(priv_dev->dev,
> + "Device address (%d) cannot be greater than %d\n",
> + addr, USB_DEVICE_MAX_ADDRESS);
> + return -EINVAL;
> + }
> +
> + if (device_state == USB_STATE_CONFIGURED) {
> + dev_err(priv_dev->dev,
> + "can't set_address from configured state\n");
> + return -EINVAL;
> + }
> +
> + reg = readl(&priv_dev->regs->usb_cmd);
> +
> + writel(reg | USB_CMD_FADDR(addr) | USB_CMD_SET_ADDR,
> + &priv_dev->regs->usb_cmd);
> +
> + usb_gadget_set_state(&priv_dev->gadget,
> + (addr ? USB_STATE_ADDRESS : USB_STATE_DEFAULT));
> +
> + cdns3_prepare_setup_packet(priv_dev);
> +
> + writel(EP_CMD_ERDY | EP_CMD_REQ_CMPL, &priv_dev->regs->ep_cmd);
> +
> + return 0;
> +}
> +
> +/**
> + * cdns3_req_ep0_get_status - Handling of GET_STATUS standard USB request
> + * @priv_dev: extended gadget object
> + * @ctrl_req: pointer to received setup packet
> + *
> + * Returns 0 if success, error code on error
> + */
> +static int cdns3_req_ep0_get_status(struct cdns3_device *priv_dev,
> + struct usb_ctrlrequest *ctrl)
> +{
> + __le16 *response_pkt;
> + u16 usb_status = 0;
> + u32 recip;
> + u32 reg;
> +
> + recip = ctrl->bRequestType & USB_RECIP_MASK;
> +
> + switch (recip) {
> + case USB_RECIP_DEVICE:
> + /* self powered */
> + if (priv_dev->is_selfpowered)
> + usb_status = BIT(USB_DEVICE_SELF_POWERED);
> +
> + if (priv_dev->wake_up_flag)
> + usb_status |= BIT(USB_DEVICE_REMOTE_WAKEUP);
> +
> + if (priv_dev->gadget.speed != USB_SPEED_SUPER)
> + break;
> +
> + reg = readl(&priv_dev->regs->usb_sts);
> +
> + if (priv_dev->u1_allowed)
> + usb_status |= BIT(USB_DEV_STAT_U1_ENABLED);
> +
> + if (priv_dev->u2_allowed)
> + usb_status |= BIT(USB_DEV_STAT_U2_ENABLED);
> +
> + break;
> + case USB_RECIP_INTERFACE:
> + return cdns3_ep0_delegate_req(priv_dev, ctrl);
> + case USB_RECIP_ENDPOINT:
> + /* check if endpoint is stalled */
> + cdns3_select_ep(priv_dev, ctrl->wIndex);
> + if (EP_STS_STALL(readl(&priv_dev->regs->ep_sts)))
> + usb_status = BIT(USB_ENDPOINT_HALT);
> + break;
> + default:
> + return -EINVAL;
> + }
> +
> + response_pkt = (__le16 *)priv_dev->setup_buf;
> + *response_pkt = cpu_to_le16(usb_status);
> +
> + cdns3_ep0_run_transfer(priv_dev, priv_dev->setup_dma,
> + sizeof(*response_pkt), 1);
> + return 0;
> +}
> +
> +static int cdns3_ep0_feature_handle_device(struct cdns3_device *priv_dev,
> + struct usb_ctrlrequest *ctrl,
> + int set)
> +{
> + enum usb_device_state state;
> + enum usb_device_speed speed;
> + int ret = 0;
> + u32 wValue;
> + u32 wIndex;
> + u16 tmode;
> +
> + wValue = le16_to_cpu(ctrl->wValue);
> + wIndex = le16_to_cpu(ctrl->wIndex);
> + state = priv_dev->gadget.state;
> + speed = priv_dev->gadget.speed;
> +
> + switch (ctrl->wValue) {
> + case USB_DEVICE_REMOTE_WAKEUP:
> + priv_dev->wake_up_flag = !!set;
> + break;
> + case USB_DEVICE_U1_ENABLE:
> + if (state != USB_STATE_CONFIGURED || speed != USB_SPEED_SUPER)
> + return -EINVAL;
> +
> + priv_dev->u1_allowed = !!set;
> + break;
> + case USB_DEVICE_U2_ENABLE:
> + if (state != USB_STATE_CONFIGURED || speed != USB_SPEED_SUPER)
> + return -EINVAL;
> +
> + priv_dev->u2_allowed = !!set;
> + break;
> + case USB_DEVICE_LTM_ENABLE:
> + ret = -EINVAL;
> + break;
> + case USB_DEVICE_TEST_MODE:
> + if (state != USB_STATE_CONFIGURED || speed > USB_SPEED_HIGH)
> + return -EINVAL;
> +
> + tmode = le16_to_cpu(ctrl->wIndex);
> +
> + if (!set || (tmode & 0xff) != 0)
> + return -EINVAL;
> +
> + switch (tmode >> 8) {
> + case TEST_J:
> + case TEST_K:
> + case TEST_SE0_NAK:
> + case TEST_PACKET:
> + cdns3_set_register_bit(&priv_dev->regs->usb_cmd,
> + USB_CMD_STMODE |
> + USB_STS_TMODE_SEL(tmode - 1));
> + break;
> + default:
> + ret = -EINVAL;
> + }
> + break;
> + default:
> + ret = -EINVAL;
> + }
> +
> + return ret;
> +}
> +
> +static int cdns3_ep0_feature_handle_intf(struct cdns3_device *priv_dev,
> + struct usb_ctrlrequest *ctrl,
> + int set)
> +{
> + u32 wValue;
> + int ret = 0;
> +
> + wValue = le16_to_cpu(ctrl->wValue);
> +
> + switch (wValue) {
> + case USB_INTRF_FUNC_SUSPEND:
> + break;
> + default:
> + ret = -EINVAL;
> + }
> +
> + return ret;
> +}
> +
> +static int cdns3_ep0_feature_handle_endpoint(struct cdns3_device *priv_dev,
> + struct usb_ctrlrequest *ctrl,
> + int set)
> +{
> + struct cdns3_endpoint *priv_ep;
> + int ret = 0;
> + u8 index;
> +
> + if (le16_to_cpu(ctrl->wValue) != USB_ENDPOINT_HALT)
> + return -EINVAL;
> +
> + if (!(ctrl->wIndex & ~USB_DIR_IN))
> + return 0;
> +
> + index = cdns3_ep_addr_to_index(ctrl->wIndex);
> + priv_ep = priv_dev->eps[index];
> +
> + cdns3_select_ep(priv_dev, ctrl->wIndex);
> +
> + if (set) {
> + writel(EP_CMD_SSTALL, &priv_dev->regs->ep_cmd);
> + priv_ep->flags |= EP_STALL;
> + } else {
> + struct usb_request *request;
> +
> + if (priv_dev->eps[index]->flags & EP_WEDGE) {
> + cdns3_select_ep(priv_dev, 0x00);
> + return 0;
> + }
> +
> + writel(EP_CMD_CSTALL | EP_CMD_EPRST, &priv_dev->regs->ep_cmd);
> +
> + /* wait for EPRST cleared */
> + ret = cdns3_handshake(&priv_dev->regs->ep_cmd,
> + EP_CMD_EPRST, 0, 100);
> + if (ret)
> + return -EINVAL;
> +
> + priv_ep->flags &= ~EP_STALL;
> +
> + request = cdns3_next_request(&priv_ep->request_list);
> + if (request)
> + cdns3_ep_run_transfer(priv_ep, request);
> + }
> + return ret;
> +}
> +
> +/**
> + * cdns3_req_ep0_handle_feature -
> + * Handling of GET/SET_FEATURE standard USB request
> + *
> + * @priv_dev: extended gadget object
> + * @ctrl_req: pointer to received setup packet
> + * @set: must be set to 1 for SET_FEATURE request
> + *
> + * Returns 0 if success, error code on error
> + */
> +static int cdns3_req_ep0_handle_feature(struct cdns3_device *priv_dev,
> + struct usb_ctrlrequest *ctrl,
> + int set)
> +{
> + int ret = 0;
> + u32 recip;
> +
> + recip = ctrl->bRequestType & USB_RECIP_MASK;
> +
> + switch (recip) {
> + case USB_RECIP_DEVICE:
> + ret = cdns3_ep0_feature_handle_device(priv_dev, ctrl, set);
> + break;
> + case USB_RECIP_INTERFACE:
> + ret = cdns3_ep0_feature_handle_intf(priv_dev, ctrl, set);
> + break;
> + case USB_RECIP_ENDPOINT:
> + ret = cdns3_ep0_feature_handle_endpoint(priv_dev, ctrl, set);
> + break;
> + default:
> + return -EINVAL;
> + }
> +
> + if (!ret)
> + writel(EP_CMD_ERDY | EP_CMD_REQ_CMPL, &priv_dev->regs->ep_cmd);
> +
> + return ret;
> +}
> +
> +/**
> + * cdns3_req_ep0_set_sel - Handling of SET_SEL standard USB request
> + * @priv_dev: extended gadget object
> + * @ctrl_req: pointer to received setup packet
> + *
> + * Returns 0 if success, error code on error
> + */
> +static int cdns3_req_ep0_set_sel(struct cdns3_device *priv_dev,
> + struct usb_ctrlrequest *ctrl_req)
> +{
> + if (priv_dev->gadget.state < USB_STATE_ADDRESS)
> + return -EINVAL;
> +
> + if (ctrl_req->wLength != 6) {
> + dev_err(priv_dev->dev, "Set SEL should be 6 bytes, got %d\n",
> + ctrl_req->wLength);
> + return -EINVAL;
> + }
> +
> + cdns3_ep0_run_transfer(priv_dev, priv_dev->setup_dma, 6, 1);
> + return 0;
> +}
> +
> +/**
> + * cdns3_req_ep0_set_isoch_delay -
> + * Handling of GET_ISOCH_DELAY standard USB request
> + * @priv_dev: extended gadget object
> + * @ctrl_req: pointer to received setup packet
> + *
> + * Returns 0 if success, error code on error
> + */
> +static int cdns3_req_ep0_set_isoch_delay(struct cdns3_device *priv_dev,
> + struct usb_ctrlrequest *ctrl_req)
> +{
> + if (ctrl_req->wIndex || ctrl_req->wLength)
> + return -EINVAL;
> +
> + priv_dev->isoch_delay = ctrl_req->wValue;
> + writel(EP_CMD_ERDY | EP_CMD_REQ_CMPL, &priv_dev->regs->ep_cmd);
> + return 0;
> +}
> +
> +/**
> + * cdns3_ep0_standard_request - Handling standard USB requests
> + * @priv_dev: extended gadget object
> + * @ctrl_req: pointer to received setup packet
> + *
> + * Returns 0 if success, error code on error
> + */
> +static int cdns3_ep0_standard_request(struct cdns3_device *priv_dev,
> + struct usb_ctrlrequest *ctrl_req)
> +{
> + int ret;
> +
> + switch (ctrl_req->bRequest) {
> + case USB_REQ_SET_ADDRESS:
> + ret = cdns3_req_ep0_set_address(priv_dev, ctrl_req);
> + break;
> + case USB_REQ_SET_CONFIGURATION:
> + ret = cdns3_req_ep0_set_configuration(priv_dev, ctrl_req);
> + break;
> + case USB_REQ_GET_STATUS:
> + ret = cdns3_req_ep0_get_status(priv_dev, ctrl_req);
> + break;
> + case USB_REQ_CLEAR_FEATURE:
> + ret = cdns3_req_ep0_handle_feature(priv_dev, ctrl_req, 0);
> + break;
> + case USB_REQ_SET_FEATURE:
> + ret = cdns3_req_ep0_handle_feature(priv_dev, ctrl_req, 1);
> + break;
> + case USB_REQ_SET_SEL:
> + ret = cdns3_req_ep0_set_sel(priv_dev, ctrl_req);
> + break;
> + case USB_REQ_SET_ISOCH_DELAY:
> + ret = cdns3_req_ep0_set_isoch_delay(priv_dev, ctrl_req);
> + break;
> + default:
> + ret = cdns3_ep0_delegate_req(priv_dev, ctrl_req);
> + break;
> + }
> +
> + return ret;
> +}
> +
> +static void __pending_setup_status_handler(struct cdns3_device *priv_dev)
> +{
> + struct usb_request *request = priv_dev->pending_status_request;
> +
> + if (priv_dev->status_completion_no_call && request &&
> + request->complete) {
> + request->complete(priv_dev->gadget.ep0, request);
> + priv_dev->status_completion_no_call = 0;
> + }
> +}
> +
> +void cdns3_pending_setup_status_handler(struct work_struct *work)
> +{
> + struct cdns3_device *priv_dev = container_of(work, struct cdns3_device,
> + pending_status_wq);
> + unsigned long flags;
> +
> + spin_lock_irqsave(&priv_dev->lock, flags);
> + __pending_setup_status_handler(priv_dev);
> + spin_unlock_irqrestore(&priv_dev->lock, flags);
> +}
> +
> +/**
> + * cdns3_gadget_ep_giveback - call struct usb_request's ->complete callback
> + * @priv_ep: The endpoint to whom the request belongs to
> + * @priv_req: The request we're giving back
> + * @status: completion code for the request
> + *
> + * Must be called with controller's lock held and interrupts disabled. This
> + * function will unmap @req and call its ->complete() callback to notify upper
> + * layers that it has completed.
> + */
> +
> +void cdns3_gadget_ep0_giveback(struct cdns3_device *priv_dev,
> + int status)
> +{
> + struct cdns3_endpoint *priv_ep;
> + struct usb_request *request;
> +
> + priv_ep = ep_to_cdns3_ep(priv_dev->gadget.ep0);
> + request = cdns3_next_request(&priv_ep->request_list);
> +
> + priv_ep->dir = priv_dev->ep0_data_dir;
> + cdns3_gadget_giveback(priv_ep, to_cdns3_request(request), status);
> + priv_dev->ep0_request = NULL;
> +}
> +
> +/**
> + * cdns3_ep0_setup_phase - Handling setup USB requests
> + * @priv_dev: extended gadget object
> + */
> +static void cdns3_ep0_setup_phase(struct cdns3_device *priv_dev)
> +{
> + struct usb_ctrlrequest *ctrl = priv_dev->setup_buf;
> + struct cdns3_endpoint *priv_ep;
> + int result;
> +
> + priv_dev->ep0_data_dir = ctrl->bRequestType & USB_DIR_IN;
> + priv_ep = ep_to_cdns3_ep(priv_dev->gadget.ep0);
> +
> + trace_cdns3_ctrl_req(ctrl);
> +
> + if (!list_empty(&priv_ep->request_list))
> + cdns3_gadget_ep0_giveback(priv_dev, -ECONNRESET);
> +
> + if ((ctrl->bRequestType & USB_TYPE_MASK) == USB_TYPE_STANDARD)
> + result = cdns3_ep0_standard_request(priv_dev, ctrl);
> + else
> + result = cdns3_ep0_delegate_req(priv_dev, ctrl);
> +
> + if (result != 0 && result != USB_GADGET_DELAYED_STATUS) {
> + dev_dbg(priv_dev->dev, "STALL for ep0\n");
> + /* set_stall on ep0 */
> + cdns3_select_ep(priv_dev, 0x00);
> + writel(EP_CMD_SSTALL, &priv_dev->regs->ep_cmd);
> + writel(EP_CMD_ERDY | EP_CMD_REQ_CMPL, &priv_dev->regs->ep_cmd);
> + }
> +}
> +
> +static void cdns3_transfer_completed(struct cdns3_device *priv_dev)
> +{
> + struct cdns3_endpoint *priv_ep = ep_to_cdns3_ep(priv_dev->gadget.ep0);
> +
> + if (priv_dev->ep0_request) {
> + trace_cdns3_complete_trb(priv_ep, priv_dev->ep0_trb);
> +
> + priv_dev->ep0_request->actual =
> + TRB_LEN(le32_to_cpu(priv_dev->ep0_trb->length));
> +
> + cdns3_gadget_ep0_giveback(priv_dev, 0);
> + }
> +
> + cdns3_prepare_setup_packet(priv_dev);
> + writel(EP_CMD_REQ_CMPL, &priv_dev->regs->ep_cmd);
> +}
> +
> +/**
> + * cdns3_check_new_setup - Check if controller receive new SETUP packet.
> + * @priv_dev: extended gadget object
> + *
> + * The SETUP packet can be kept in on-chip memory or in system memory.
> + */
> +static bool cdns3_check_new_setup(struct cdns3_device *priv_dev)
> +{
> + u32 ep_sts_reg;
> +
> + cdns3_select_ep(priv_dev, 0 | USB_DIR_OUT);
> + ep_sts_reg = readl(&priv_dev->regs->ep_sts);
> +
> + return !!(ep_sts_reg & (EP_STS_SETUP | EP_STS_STPWAIT));
> +}
> +
> +/**
> + * cdns3_check_ep0_interrupt_proceed - Processes interrupt related to endpoint 0
> + * @priv_dev: extended gadget object
> + * @dir: USB_DIR_IN for IN direction, USB_DIR_OUT for OUT direction
> + */
> +void cdns3_check_ep0_interrupt_proceed(struct cdns3_device *priv_dev, int dir)
> +{
> + u32 ep_sts_reg;
> +
> + cdns3_select_ep(priv_dev, dir);
> +
> + ep_sts_reg = readl(&priv_dev->regs->ep_sts);
> + writel(ep_sts_reg, &priv_dev->regs->ep_sts);
> +
> + trace_cdns3_ep0_irq(priv_dev);
> +
> + __pending_setup_status_handler(priv_dev);
> +
> + if ((ep_sts_reg & EP_STS_SETUP)) {
> + cdns3_ep0_setup_phase(priv_dev);
> + } else if ((ep_sts_reg & EP_STS_IOC) || (ep_sts_reg & EP_STS_ISP)) {
> + priv_dev->ep0_data_dir = dir;
> + cdns3_transfer_completed(priv_dev);
> + }
> +
> + if (ep_sts_reg & EP_STS_DESCMIS) {
> + if (dir == 0 && !priv_dev->setup_pending)
> + cdns3_prepare_setup_packet(priv_dev);
> + }
> +}
> +
> +/**
> + * cdns3_gadget_ep0_enable
> + * Function shouldn't be called by gadget driver,
> + * endpoint 0 is allways active
> + */
> +static int cdns3_gadget_ep0_enable(struct usb_ep *ep,
> + const struct usb_endpoint_descriptor *desc)
> +{
> + return -EINVAL;
> +}
> +
> +/**
> + * cdns3_gadget_ep0_disable
> + * Function shouldn't be called by gadget driver,
> + * endpoint 0 is allways active
> + */
> +static int cdns3_gadget_ep0_disable(struct usb_ep *ep)
> +{
> + return -EINVAL;
> +}
> +
> +/**
> + * cdns3_gadget_ep0_set_halt
> + * @ep: pointer to endpoint zero object
> + * @value: 1 for set stall, 0 for clear stall
> + *
> + * Returns 0
> + */
> +static int cdns3_gadget_ep0_set_halt(struct usb_ep *ep, int value)
> +{
> + /* TODO */
> + return 0;
> +}
> +
> +/**
> + * cdns3_gadget_ep0_queue Transfer data on endpoint zero
> + * @ep: pointer to endpoint zero object
> + * @request: pointer to request object
> + * @gfp_flags: gfp flags
> + *
> + * Returns 0 on success, error code elsewhere
> + */
> +static int cdns3_gadget_ep0_queue(struct usb_ep *ep,
> + struct usb_request *request,
> + gfp_t gfp_flags)
> +{
> + struct cdns3_endpoint *priv_ep = ep_to_cdns3_ep(ep);
> + struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
> + unsigned long flags;
> + int erdy_sent = 0;
> + int ret = 0;
> +
> + dev_dbg(priv_dev->dev, "Queue to Ep0%s L: %d\n",
> + priv_dev->ep0_data_dir ? "IN" : "OUT",
> + request->length);
> +
> + /* cancel the request if controller receive new SETUP packet. */
> + if (cdns3_check_new_setup(priv_dev))
> + return -ECONNRESET;
> +
> + /* send STATUS stage. Should be called only for SET_CONFIGURATION */
> + if (request->length == 0 && request->zero == 0) {
> + spin_lock_irqsave(&priv_dev->lock, flags);
> + cdns3_select_ep(priv_dev, 0x00);
> +
> + erdy_sent = !priv_dev->hw_configured_flag;
> + cdns3_set_hw_configuration(priv_dev);
> +
> + if (!erdy_sent)
> + writel(EP_CMD_ERDY | EP_CMD_REQ_CMPL,
> + &priv_dev->regs->ep_cmd);
> +
> + cdns3_prepare_setup_packet(priv_dev);
> + request->actual = 0;
> + priv_dev->status_completion_no_call = true;
> + priv_dev->pending_status_request = request;
> + spin_unlock_irqrestore(&priv_dev->lock, flags);
> +
> + /*
> + * Since there is no completion interrupt for status stage,
> + * it needs to call ->completion in software after
> + * ep0_queue is back.
> + */
> + queue_work(system_freezable_wq, &priv_dev->pending_status_wq);
> + return 0;
> + }
> +
> + spin_lock_irqsave(&priv_dev->lock, flags);
> + if (!list_empty(&priv_ep->request_list)) {
> + dev_err(priv_dev->dev,
> + "can't handle multiple requests for ep0\n");
> + spin_unlock_irqrestore(&priv_dev->lock, flags);
> + return -EBUSY;
> + }
> +
> + ret = usb_gadget_map_request_by_dev(priv_dev->sysdev, request,
> + priv_dev->ep0_data_dir);
> + if (ret) {
> + spin_unlock_irqrestore(&priv_dev->lock, flags);
> + dev_err(priv_dev->dev, "failed to map request\n");
> + return -EINVAL;
> + }
> +
> + request->status = -EINPROGRESS;
> + priv_dev->ep0_request = request;
> + list_add_tail(&request->list, &priv_ep->request_list);
> + cdns3_ep0_run_transfer(priv_dev, request->dma, request->length, 1);
> + spin_unlock_irqrestore(&priv_dev->lock, flags);
> +
> + return ret;
> +}
> +
> +/**
> + * cdns3_gadget_ep_set_wedge Set wedge on selected endpoint
> + * @ep: endpoint object
> + *
> + * Returns 0
> + */
> +int cdns3_gadget_ep_set_wedge(struct usb_ep *ep)
> +{
> + struct cdns3_endpoint *priv_ep = ep_to_cdns3_ep(ep);
> + struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
> +
> + dev_dbg(priv_dev->dev, "Wedge for %s\n", ep->name);
> + cdns3_gadget_ep_set_halt(ep, 1);
> + priv_ep->flags |= EP_WEDGE;
> +
> + return 0;
> +}
> +
> +const struct usb_ep_ops cdns3_gadget_ep0_ops = {
> + .enable = cdns3_gadget_ep0_enable,
> + .disable = cdns3_gadget_ep0_disable,
> + .alloc_request = cdns3_gadget_ep_alloc_request,
> + .free_request = cdns3_gadget_ep_free_request,
> + .queue = cdns3_gadget_ep0_queue,
> + .dequeue = cdns3_gadget_ep_dequeue,
> + .set_halt = cdns3_gadget_ep0_set_halt,
> + .set_wedge = cdns3_gadget_ep_set_wedge,
> +};
> +
> +/**
> + * cdns3_ep0_config - Configures default endpoint
> + * @priv_dev: extended gadget object
> + *
> + * Functions sets parameters: maximal packet size and enables interrupts
> + */
> +void cdns3_ep0_config(struct cdns3_device *priv_dev)
> +{
> + struct cdns3_usb_regs __iomem *regs;
> + u32 max_packet_size = 64;
> +
> + regs = priv_dev->regs;
> +
> + if (priv_dev->gadget.speed == USB_SPEED_SUPER)
> + max_packet_size = 512;
> +
> + if (priv_dev->ep0_request) {
> + list_del_init(&priv_dev->ep0_request->list);
> + priv_dev->ep0_request = NULL;
> + }
> +
> + priv_dev->u1_allowed = 0;
> + priv_dev->u2_allowed = 0;
> +
> + priv_dev->gadget.ep0->maxpacket = max_packet_size;
> + cdns3_gadget_ep0_desc.wMaxPacketSize = cpu_to_le16(max_packet_size);
> +
> + /* init ep out */
> + cdns3_select_ep(priv_dev, USB_DIR_OUT);
> +
> + writel(EP_CFG_ENABLE | EP_CFG_MAXPKTSIZE(max_packet_size),
> + &regs->ep_cfg);
> +
> + writel(EP_STS_EN_SETUPEN | EP_STS_EN_DESCMISEN | EP_STS_EN_TRBERREN,
> + &regs->ep_sts_en);
> +
> + /* init ep in */
> + cdns3_select_ep(priv_dev, USB_DIR_IN);
> +
> + writel(EP_CFG_ENABLE | EP_CFG_MAXPKTSIZE(max_packet_size),
> + &regs->ep_cfg);
> +
> + writel(EP_STS_EN_SETUPEN | EP_STS_EN_TRBERREN, &regs->ep_sts_en);
> +
> + cdns3_set_register_bit(&regs->usb_conf, USB_CONF_U1DS | USB_CONF_U2DS);
> + cdns3_prepare_setup_packet(priv_dev);
> +}
> +
> +/**
> + * cdns3_init_ep0 Initializes software endpoint 0 of gadget
> + * @cdns3: extended gadget object
> + *
> + * Returns 0 on success, error code elsewhere
> + */
> +int cdns3_init_ep0(struct cdns3_device *priv_dev)
> +{
> + struct cdns3_endpoint *ep0;
> +
> + ep0 = devm_kzalloc(priv_dev->dev, sizeof(struct cdns3_endpoint),
> + GFP_KERNEL);
> +
> + if (!ep0)
> + return -ENOMEM;
> +
> + ep0->cdns3_dev = priv_dev;
> + sprintf(ep0->name, "ep0");
> +
> + /* fill linux fields */
> + ep0->endpoint.ops = &cdns3_gadget_ep0_ops;
> + ep0->endpoint.maxburst = 1;
> + usb_ep_set_maxpacket_limit(&ep0->endpoint, CDNS3_EP0_MAX_PACKET_LIMIT);
> + ep0->endpoint.address = 0;
> + ep0->endpoint.caps.type_control = 1;
> + ep0->endpoint.caps.dir_in = 1;
> + ep0->endpoint.caps.dir_out = 1;
> + ep0->endpoint.name = ep0->name;
> + ep0->endpoint.desc = &cdns3_gadget_ep0_desc;
> + priv_dev->gadget.ep0 = &ep0->endpoint;
> + INIT_LIST_HEAD(&ep0->request_list);
> +
> + return 0;
> +}
> diff --git a/drivers/usb/cdns3/gadget-export.h b/drivers/usb/cdns3/gadget-export.h
> new file mode 100644
> index 000000000000..577469eee961
> --- /dev/null
> +++ b/drivers/usb/cdns3/gadget-export.h
> @@ -0,0 +1,28 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * Cadence USBSS DRD Driver - Gadget Export APIs.
> + *
> + * Copyright (C) 2017 NXP
> + * Copyright (C) 2017-2018 NXP
> + *
> + * Authors: Peter Chen <[email protected]>
> + */
> +#ifndef __LINUX_CDNS3_GADGET_EXPORT
> +#define __LINUX_CDNS3_GADGET_EXPORT
> +
> +#ifdef CONFIG_USB_CDNS3_GADGET
> +
> +int cdns3_gadget_init(struct cdns3 *cdns);
> +void cdns3_gadget_exit(struct cdns3 *cdns);
> +#else
> +
> +static inline int cdns3_gadget_init(struct cdns3 *cdns)
> +{
> + return -ENXIO;
> +}
> +
> +static inline void cdns3_gadget_exit(struct cdns3 *cdns) { }
> +
> +#endif
> +
> +#endif /* __LINUX_CDNS3_GADGET_EXPORT */
> diff --git a/drivers/usb/cdns3/gadget.c b/drivers/usb/cdns3/gadget.c
> new file mode 100644
> index 000000000000..a021eaf07aee
> --- /dev/null
> +++ b/drivers/usb/cdns3/gadget.c
> @@ -0,0 +1,1802 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Cadence USBSS DRD Driver - gadget side.
> + *
> + * Copyright (C) 2018 Cadence Design Systems.
> + * Copyright (C) 2017-2018 NXP
> + *
> + * Authors: Pawel Jez <[email protected]>,
> + * Pawel Laszczak <[email protected]>
> + * Peter Chen <[email protected]>
> + */
> +
> +#include <linux/dma-mapping.h>
> +#include <linux/usb/gadget.h>
> +
> +#include "core.h"
> +#include "gadget-export.h"
> +#include "gadget.h"
> +
> +#include "trace.h"
> +
> +static int __cdns3_gadget_ep_queue(struct usb_ep *ep,
> + struct usb_request *request,
> + gfp_t gfp_flags);
> +
> +/**
> + * cdns3_handshake - spin reading until handshake completes or fails
> + * @ptr: address of device controller register to be read
> + * @mask: bits to look at in result of read
> + * @done: value of those bits when handshake succeeds
> + * @usec: timeout in microseconds
> + *
> + * Returns negative errno, or zero on success
> + *
> + * Success happens when the "mask" bits have the specified value (hardware
> + * handshake done). There are two failure modes: "usec" have passed (major
> + * hardware flakeout), or the register reads as all-ones (hardware removed).
> + */
> +int cdns3_handshake(void __iomem *ptr, u32 mask, u32 done, int usec)
> +{
> + u32 result;
> +
> + do {
> + result = readl(ptr);
> + if (result == ~(u32)0) /* card removed */
> + return -ENODEV;
> + result &= mask;
> + if (result == done)
> + return 0;
> + udelay(1);
> + usec--;
> + } while (usec > 0);
> + return -ETIMEDOUT;
> +}
> +
> +/**
> + * cdns3_set_register_bit - set bit in given register.
> + * @ptr: address of device controller register to be read and changed
> + * @mask: bits requested to set
> + */
> +void cdns3_set_register_bit(void __iomem *ptr, u32 mask)
> +{
> + mask = readl(ptr) | mask;
> + writel(mask, ptr);
> +}
> +
> +/**
> + * cdns3_ep_reg_pos_to_index - Macro converts bit position of ep_ists register
> + * to index of endpoint object in cdns3_device.eps[] container
> + * @i: bit position of endpoint for which endpoint object is required
> + *
> + * Remember that endpoint container doesn't contain default endpoint
> + */
> +static u8 cdns3_ep_reg_pos_to_index(int i)
> +{
> + return ((i / 16) + (((i % 16) - 2) * 2));
> +}
> +
> +/**
> + * cdns3_ep_addr_to_index - Macro converts endpoint address to
> + * index of endpoint object in cdns3_device.eps[] container
> + * @ep_addr: endpoint address for which endpoint object is required
> + *
> + * Remember that endpoint container doesn't contain default endpoint
> + */
> +u8 cdns3_ep_addr_to_index(u8 ep_addr)
> +{
> + return (((ep_addr & 0x7F) - 1) + ((ep_addr & USB_DIR_IN) ? 1 : 0));
> +}
> +
> +/**
> + * cdns3_ep_addr_to_bit_pos - Macro converts endpoint address to
> + * bit position in ep_ists register
> + * @ep_addr: endpoint address for which bit position is required
> + *
> + * Remember that endpoint container doesn't contain default endpoint
> + */
> +static u32 cdns3_ep_addr_to_bit_pos(u8 ep_addr)
> +{
> + return (1 << (ep_addr & 0x7F)) << ((ep_addr & 0x80) ? 16 : 0);
> +}
> +
> +/**
> + * cdns3_next_request - returns next request from list
> + * @list: list containing requests
> + *
> + * Returns request or NULL if no requests in list
> + */
> +struct usb_request *cdns3_next_request(struct list_head *list)
> +{
> + if (list_empty(list))
> + return NULL;
> + return list_first_entry(list, struct usb_request, list);
> +}
> +
> +/**
> + * select_ep - selects endpoint
> + * @priv_dev: extended gadget object
> + * @ep: endpoint address
> + */
> +void cdns3_select_ep(struct cdns3_device *priv_dev, u32 ep)
> +{
> + if (priv_dev->selected_ep == ep)
> + return;
> +
> + priv_dev->selected_ep = ep;
> + writel(ep, &priv_dev->regs->ep_sel);
> +}
> +
> +dma_addr_t cdns3_trb_virt_to_dma(struct cdns3_endpoint *priv_ep,
> + struct cdns3_trb *trb)
> +{
> + u32 offset = (char *)trb - (char *)priv_ep->trb_pool;
> +
> + return priv_ep->trb_pool_dma + offset;
> +}
> +
> +/**
> + * cdns3_allocate_trb_pool - Allocates TRB's pool for selected endpoint
> + * @priv_ep: endpoint object
> + *
> + * Function will return 0 on success or -ENOMEM on allocation error
> + */
> +static int cdns3_allocate_trb_pool(struct cdns3_endpoint *priv_ep)
> +{
> + struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
> + struct cdns3_trb *link_trb;
> +
> + if (!priv_ep->trb_pool) {
> + priv_ep->trb_pool = dma_zalloc_coherent(priv_dev->sysdev,
> + TRB_RING_SIZE,
> + &priv_ep->trb_pool_dma,
> + GFP_DMA);
> + if (!priv_ep->trb_pool)
> + return -ENOMEM;
> + } else {
> + memset(priv_ep->trb_pool, 0, TRB_RING_SIZE);
> + }
> +
> + if (!priv_ep->aligned_buff) {
> + void *buff = dma_alloc_coherent(priv_dev->sysdev,
> + CDNS3_ALIGNED_BUF_SIZE,
> + &priv_ep->aligned_dma_addr,
> + GFP_DMA);
> +
> + priv_ep->aligned_buff = buff;
> + if (!priv_ep->aligned_buff) {
> + dma_free_coherent(priv_dev->sysdev,
> + TRB_RING_SIZE,
> + priv_ep->trb_pool,
> + priv_ep->trb_pool_dma);
> + priv_ep->trb_pool = NULL;
> +
> + return -ENOMEM;
> + }
> + }
> +
> + /* Initialize the last TRB as Link TRB */
> + link_trb = (priv_ep->trb_pool + TRBS_PER_SEGMENT - 1);
> + link_trb->buffer = TRB_BUFFER(priv_ep->trb_pool_dma);
> + link_trb->control = TRB_CYCLE | TRB_TYPE(TRB_LINK) |
> + TRB_CHAIN | TRB_TOGGLE;
> +
> + return 0;
> +}
> +
> +static void cdns3_free_trb_pool(struct cdns3_endpoint *priv_ep)
> +{
> + struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
> +
> + if (priv_ep->trb_pool) {
> + dma_free_coherent(priv_dev->sysdev,
> + TRB_RING_SIZE,
> + priv_ep->trb_pool, priv_ep->trb_pool_dma);
> + priv_ep->trb_pool = NULL;
> + }
> +
> + if (priv_ep->aligned_buff) {
> + dma_free_coherent(priv_dev->sysdev, CDNS3_ALIGNED_BUF_SIZE,
> + priv_ep->aligned_buff,
> + priv_ep->aligned_dma_addr);
> + priv_ep->aligned_buff = NULL;
> + }
> +}
> +
> +/**
> + * cdns3_data_flush - flush data at onchip buffer
> + * @priv_ep: endpoint object
> + *
> + * Endpoint must be selected before call to this function
> + *
> + * Returns zero on success or negative value on failure
> + */
> +static int cdns3_data_flush(struct cdns3_endpoint *priv_ep)
> +{
> + struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
> +
> + writel(EP_CMD_DFLUSH, &priv_dev->regs->ep_cmd);
> +
> + /* wait for DFLUSH cleared */
> + return cdns3_handshake(&priv_dev->regs->ep_cmd, EP_CMD_DFLUSH, 0, 100);
> +}
> +
> +/**
> + * cdns3_ep_stall_flush - Stalls and flushes selected endpoint
> + * @priv_ep: endpoint object
> + *
> + * Endpoint must be selected before call to this function
> + */
> +static void cdns3_ep_stall_flush(struct cdns3_endpoint *priv_ep)
> +{
> + struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
> +
> + writel(EP_CMD_DFLUSH | EP_CMD_ERDY | EP_CMD_SSTALL,
> + &priv_dev->regs->ep_cmd);
> +
> + /* wait for DFLUSH cleared */
> + cdns3_handshake(&priv_dev->regs->ep_cmd, EP_CMD_DFLUSH, 0, 100);
> + priv_ep->flags |= EP_STALL;
> +}
> +
> +/**
> + * cdns3_gadget_unconfig - reset device configuration
> + * @priv_dev: extended gadget object
> + */
> +void cdns3_gadget_unconfig(struct cdns3_device *priv_dev)
> +{
> + /* RESET CONFIGURATION */
> + writel(USB_CONF_CFGRST, &priv_dev->regs->usb_conf);
> +
> + cdns3_allow_enable_l1(priv_dev, 0);
> + priv_dev->hw_configured_flag = 0;
> + priv_dev->onchip_mem_allocated_size = 0;
> +}
> +
> +/**
> + * cdns3_ep_inc_trb - increment a trb index.
> + * @index: Pointer to the TRB index to increment.
> + * @cs: Cycle state
> + *
> + * The index should never point to the link TRB. After incrementing,
> + * if it is point to the link TRB, wrap around to the beginning and revert
> + * cycle state bit The
> + * link TRB is always at the last TRB entry.
> + */
> +static void cdns3_ep_inc_trb(int *index, u8 *cs)
> +{
> + (*index)++;
> + if (*index == (TRBS_PER_SEGMENT - 1)) {
> + *index = 0;
> + *cs ^= 1;
> + }
> +}
> +
> +/**
> + * cdns3_ep_inc_enq - increment endpoint's enqueue pointer
> + * @priv_ep: The endpoint whose enqueue pointer we're incrementing
> + */
> +static void cdns3_ep_inc_enq(struct cdns3_endpoint *priv_ep)
> +{
> + priv_ep->free_trbs--;
> + cdns3_ep_inc_trb(&priv_ep->enqueue, &priv_ep->pcs);
> +}
> +
> +/**
> + * cdns3_ep_inc_deq - increment endpoint's dequeue pointer
> + * @priv_ep: The endpoint whose dequeue pointer we're incrementing
> + */
> +static void cdns3_ep_inc_deq(struct cdns3_endpoint *priv_ep)
> +{
> + priv_ep->free_trbs++;
> + cdns3_ep_inc_trb(&priv_ep->dequeue, &priv_ep->ccs);
> +}
> +
> +/**
> + * cdns3_allow_enable_l1 - enable/disable permits to transition to L1.
> + * @priv_dev: Extended gadget object
> + * @enable: Enable/disable permit to transition to L1.
> + *
> + * If bit USB_CONF_L1EN is set and device receive Extended Token packet,
> + * then controller answer with ACK handshake.
> + * If bit USB_CONF_L1DS is set and device receive Extended Token packet,
> + * then controller answer with NYET handshake.
> + */
> +void cdns3_allow_enable_l1(struct cdns3_device *priv_dev, int enable)
> +{
> + if (enable)
> + writel(USB_CONF_L1EN, &priv_dev->regs->usb_conf);
> + else
> + writel(USB_CONF_L1DS, &priv_dev->regs->usb_conf);
> +}
> +
> +enum usb_device_speed cdns3_get_speed(struct cdns3_device *priv_dev)
> +{
> + u32 reg;
> +
> + reg = readl(&priv_dev->regs->usb_sts);
> +
> + if (DEV_SUPERSPEED(reg))
> + return USB_SPEED_SUPER;
> + else if (DEV_HIGHSPEED(reg))
> + return USB_SPEED_HIGH;
> + else if (DEV_FULLSPEED(reg))
> + return USB_SPEED_FULL;
> + else if (DEV_LOWSPEED(reg))
> + return USB_SPEED_LOW;
> + return USB_SPEED_UNKNOWN;
> +}
> +
> +/**
> + * cdns3_start_all_request - add to ring all request not started
> + * @priv_dev: Extended gadget object
> + * @priv_ep: The endpoint for whom request will be started.
> + *
> + * Returns return ENOMEM if transfer ring i not enough TRBs to start
> + * all requests.
> + */
> +static int cdns3_start_all_request(struct cdns3_device *priv_dev,
> + struct cdns3_endpoint *priv_ep)
> +{
> + struct usb_request *req, *req_temp;
> + int ret = 0;
> +
> + list_for_each_entry_safe(req, req_temp, &priv_ep->request_list, list) {
> + struct cdns3_request *priv_req = to_cdns3_request(req);
> +
> + if (!(priv_req->flags & REQUEST_PENDING)) {
> + ret = cdns3_ep_run_transfer(priv_ep, req);
> + if (ret)
> + return ret;
> + }
> + }
> +
> + priv_ep->flags &= ~EP_RING_FULL;
> + return ret;
> +}
> +
> +/**
> + * cdns3_gadget_giveback - call struct usb_request's ->complete callback
> + * @priv_ep: The endpoint to whom the request belongs to
> + * @priv_req: The request we're giving back
> + * @status: completion code for the request
> + *
> + * Must be called with controller's lock held and interrupts disabled. This
> + * function will unmap @req and call its ->complete() callback to notify upper
> + * layers that it has completed.
> + */
> +void cdns3_gadget_giveback(struct cdns3_endpoint *priv_ep,
> + struct cdns3_request *priv_req,
> + int status)
> +{
> + struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
> + struct usb_request *request = &priv_req->request;
> +
> + list_del_init(&request->list);
> +
> + if (request->status == -EINPROGRESS)
> + request->status = status;
> +
> + usb_gadget_unmap_request_by_dev(priv_dev->sysdev, request,
> + priv_ep->dir);
> +
> + priv_req->flags &= ~REQUEST_PENDING;
> + trace_cdns3_gadget_giveback(priv_req);
> +
> + if (priv_req->flags & REQUEST_INTERNAL) {
> + struct usb_request *req;
> +
> + req = cdns3_next_request(&priv_ep->request_list);
> +
> + priv_ep->descmis_pending = false;
> + priv_ep->descmis_finished = true;
> +
> + /*
> + * If no request is queued then driver can't do nothing
> + * with just completed request. Request with flag set to
> + * REQUEST_INTERNAL is only internal used request and driver
> + * can't call complete callback. Before calling completion, data
> + * must be copied to normal usb_request object
> + */
> + if (!req)
> + return;
> +
> + req->actual = request->actual;
> + req->status = request->status;
> + memcpy(req->buf, request->buf, request->actual);
> +
> + request = req;
> + list_del_init(&request->list);
> + cdns3_start_all_request(priv_dev, priv_ep);
> + priv_ep->descmis_finished = false;
> + }
> +
> + /* Start all not pending request */
> + if (priv_ep->flags & EP_RING_FULL)
> + cdns3_start_all_request(priv_dev, priv_ep);
> +
> + if (request->complete) {
> + spin_unlock(&priv_dev->lock);
> + usb_gadget_giveback_request(&priv_ep->endpoint,
> + request);
> + spin_lock(&priv_dev->lock);
> + }
> +
> + if (request->buf == priv_dev->zlp_buf)
> + cdns3_gadget_ep_free_request(&priv_ep->endpoint, request);
> +}
> +
> +/**
> + * cdns3_ep_run_transfer - start transfer on no-default endpoint hardware
> + * @priv_ep: endpoint object
> + *
> + * Returns zero on success or negative value on failure
> + */
> +int cdns3_ep_run_transfer(struct cdns3_endpoint *priv_ep,
> + struct usb_request *request)
> +{
> + struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
> + struct cdns3_request *priv_req;
> + struct cdns3_trb *trb;
> + dma_addr_t trb_dma;
> + int sg_iter = 0;
> + u32 first_pcs;
> + int num_trb;
> + int address;
> + int pcs;
> +
> + num_trb = request->num_sgs ? request->num_sgs : 1;
> +
> + if (num_trb > priv_ep->free_trbs) {
> + priv_ep->flags |= EP_RING_FULL;
> + return -ENOMEM;
> + }
> +
> + priv_req = to_cdns3_request(request);
> + address = priv_ep->endpoint.desc->bEndpointAddress;
> +
> + if (priv_ep->descmis_pending)
> + return 0;
> +
> + if (priv_req->flags & REQUEST_PENDING)
> + goto arm;
> +
> + priv_ep->flags |= EP_PENDING_REQUEST;
> + trb_dma = request->dma;
> +
> + /* must allocate buffer aligned to 8 */
> + if ((request->dma % 8)) {
> + if (request->length <= CDNS3_ALIGNED_BUF_SIZE) {
> + memcpy(priv_ep->aligned_buff, request->buf,
> + request->length);
> + trb_dma = priv_ep->aligned_dma_addr;
> + } else {
> + return -ENOMEM;
> + }
> + }
> +
> + trb = priv_ep->trb_pool + priv_ep->enqueue;
> + priv_req->trb = trb;
> + priv_req->start_trb = priv_ep->enqueue;
> +
> + /* prepare ring */
> + if ((priv_ep->enqueue + num_trb) >= (TRBS_PER_SEGMENT - 1)) {
> + /*updating C bt in Link TRB before starting DMA*/
> + struct cdns3_trb *link_trb = priv_ep->trb_pool +
> + (TRBS_PER_SEGMENT - 1);
> + link_trb->control = ((priv_ep->pcs) ? TRB_CYCLE : 0) |
> + TRB_TYPE(TRB_LINK) | TRB_CHAIN |
> + TRB_TOGGLE;
> + }
> +
> + first_pcs = priv_ep->pcs ? TRB_CYCLE : 0;
> +
> + do {
> + /* fill TRB */
> + trb->buffer = TRB_BUFFER(request->num_sgs == 0
> + ? trb_dma : request->sg[sg_iter].dma_address);
> +
> + trb->length = TRB_BURST_LEN(16) |
> + TRB_LEN(request->num_sgs == 0 ?
> + request->length : request->sg[sg_iter].length);
> +
> + trb->control = TRB_TYPE(TRB_NORMAL);
> + pcs = priv_ep->pcs ? TRB_CYCLE : 0;
> +
> + /*
> + * first trb should be prepared as last to avoid processing
> + * transfer to early
> + */
> + if (sg_iter == request->num_sgs && sg_iter != 0)
> + trb->control |= pcs | TRB_IOC | TRB_ISP;
> + else if (sg_iter != 0)
> + trb->control |= pcs;
> +
> + ++sg_iter;
> + ++trb;
> + cdns3_ep_inc_enq(priv_ep);
> + } while (sg_iter < request->num_sgs);
> +
> + trb = priv_req->trb;
> + /*
> + * Memory barrier = Cycle Bit must be set before trb->length and
> + * trb->buffer fields.
> + */
> + wmb();
> +
> + /* give the TD to the consumer*/
> + if (sg_iter == 1)
> + trb->control |= first_pcs | TRB_IOC | TRB_ISP;
> + else
> + trb->control |= first_pcs;
> +
> + priv_req->flags |= REQUEST_PENDING;
> +
> + if (priv_req->flags & REQUEST_INTERNAL)
> + priv_ep->descmis_pending = true;
> +
> + trace_cdns3_prepare_trb(priv_ep, priv_req->trb);
> + trace_cdns3_ring(priv_ep);
> +
> +arm:
> + /* arm transfer on selected endpoint */
> + cdns3_select_ep(priv_ep->cdns3_dev, address);
> +
> + /*
> + * For DMULT mode we can set address to transfer ring only once after
> + * enabling endpoint.
> + */
> + if (priv_ep->flags & EP_UPDATE_EP_TRBADDR) {
> + writel(EP_TRADDR_TRADDR(priv_ep->trb_pool_dma),
> + &priv_dev->regs->ep_traddr);
> + priv_ep->flags &= ~EP_UPDATE_EP_TRBADDR;
> + }
> +
> + if (priv_dev->hw_configured_flag) {
> + /*clearing TRBERR and EP_STS_DESCMIS before seting DRDY*/
> + writel(EP_STS_TRBERR | EP_STS_DESCMIS, &priv_dev->regs->ep_sts);
> + trace_cdns3_doorbell_epx(priv_ep->name);
> + writel(EP_CMD_DRDY, &priv_dev->regs->ep_cmd);
> + }
> +
> + return 0;
> +}
> +
> +void cdns3_set_hw_configuration(struct cdns3_device *priv_dev)
> +{
> + struct cdns3_endpoint *priv_ep;
> + struct usb_request *request;
> + struct usb_ep *ep;
> + int result = 0;
> +
> + if (priv_dev->hw_configured_flag)
> + return;
> +
> + writel(USB_CONF_CFGSET, &priv_dev->regs->usb_conf);
> + writel(EP_CMD_ERDY | EP_CMD_REQ_CMPL, &priv_dev->regs->ep_cmd);
> +
> + cdns3_set_register_bit(&priv_dev->regs->usb_conf,
> + USB_CONF_U1EN | USB_CONF_U2EN);
> +
> + /* wait until configuration set */
> + result = cdns3_handshake(&priv_dev->regs->usb_sts,
> + USB_STS_CFGSTS_MASK, 1, 100);
> +
> + priv_dev->hw_configured_flag = 1;
> + cdns3_allow_enable_l1(priv_dev, 1);
> +
> + list_for_each_entry(ep, &priv_dev->gadget.ep_list, ep_list) {
> + if (ep->enabled) {
> + priv_ep = ep_to_cdns3_ep(ep);
> + request = cdns3_next_request(&priv_ep->request_list);
> + if (request)
> + cdns3_ep_run_transfer(priv_ep, request);
> + }
> + }
> +}
> +
> +static bool cdns3_request_handled(struct cdns3_endpoint *priv_ep,
> + struct cdns3_request *priv_req)
> +{
> + int current_index;
> + struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
> + struct cdns3_trb *trb = priv_req->trb;
> +
> + if (!(priv_req->flags & REQUEST_PENDING))
> + return false;
> +
> + cdns3_select_ep(priv_dev, priv_ep->endpoint.desc->bEndpointAddress);
> + current_index = (readl(&priv_dev->regs->ep_traddr) -
> + priv_ep->trb_pool_dma) / TRB_SIZE;
> +
> + trb = &priv_ep->trb_pool[priv_req->start_trb];
> +
> + if ((trb->control & TRB_CYCLE) != priv_ep->ccs)
> + return false;
> +
> + /**
> + * case where ep_traddr point to last trb in ring (link trb)
> + * and dequeue pointer already has been changed to first trb
> + */
> + if ((current_index == (TRBS_PER_SEGMENT - 1)) && !priv_ep->dequeue)
> + return false;
> +
> + if (priv_req->start_trb != current_index)
> + return true;
> +
> + return false;
> +}
> +
> +static void cdns3_transfer_completed(struct cdns3_device *priv_dev,
> + struct cdns3_endpoint *priv_ep)
> +{
> + struct usb_request *request;
> + struct cdns3_request *priv_req;
> + struct cdns3_trb *trb;
> +
> + while (!list_empty(&priv_ep->request_list)) {
> + request = cdns3_next_request(&priv_ep->request_list);
> + priv_req = to_cdns3_request(request);
> +
> + if (!cdns3_request_handled(priv_ep, priv_req))
> + return;
> +
> + if (request->dma % 8 && priv_ep->dir == USB_DIR_OUT)
> + memcpy(request->buf, priv_ep->aligned_buff,
> + request->length);
> +
> + trb = priv_ep->trb_pool + priv_ep->dequeue;
> + trace_cdns3_complete_trb(priv_ep, trb);
> + if (trb != priv_req->trb)
> + dev_warn(priv_dev->dev,
> + "request_trb=0x%p, queue_trb=0x%p\n",
> + priv_req->trb, trb);
> +
> + request->actual = TRB_LEN(le32_to_cpu(trb->length));
> +
> + cdns3_ep_inc_deq(priv_ep);
> +
> + cdns3_gadget_giveback(priv_ep, priv_req, 0);
> + }
> +
> + priv_ep->flags &= ~EP_PENDING_REQUEST;
> +}
> +
> +/**
> + * cdns3_descmissing_packet - handles descriptor missing event.
> + * @priv_dev: extended gadget object
> + *
> + * Function protects gadget functions from getting stuck.
> + * Controller for OUT endpoints has shared on-chip buffers for all incoming
> + * packets, including ep0out. It's FIFO buffer, so packets must be handle by DMA
> + * in correct order. If the first packet in the buffer will not be handled,
> + * then the following packets directed for other endpoints and functions
> + * will be blocked.
> + * Additionally the packets directed to one endpoint can clog entire on-chip
> + * buffers. In this case transfer to other endpoints also will blocked.
> + *
> + * To resolve this issue after raising the descriptor missing interrupt
> + * driver prepares internal usb_request object and use it to arm DMA transfer
> + * for the right endpoint. Driver use only single usb_request with
> + * allocated 64KB buffer, so if host send more not expected transfers, then only
> + * the last will be saved and returned to gadget function.
> + * Such blocking situation was observed on ACM gadget, because host send OUT
> + * data packet but ACM function doesn't want their.
> + */
> +static void cdns3_descmissing_packet(struct cdns3_endpoint *priv_ep)
> +{
> + struct cdns3_request *priv_req = priv_ep->descmis_req;
> + struct usb_request *request;
> +
> + if (!priv_req) {
> + request = cdns3_gadget_ep_alloc_request(&priv_ep->endpoint,
> + GFP_ATOMIC);
> + priv_req = to_cdns3_request(request);
> + priv_req->flags |= REQUEST_INTERNAL;
> + priv_req->request.buf = kzalloc(CDNS3_DESCMIS_BUF_SIZE,
> + GFP_ATOMIC);
> + priv_req->request.length = CDNS3_DESCMIS_BUF_SIZE;
> + priv_ep->descmis_req = priv_req;
> + }
> +
> + priv_ep->descmis_finished = false;
> + __cdns3_gadget_ep_queue(&priv_ep->endpoint,
> + &priv_ep->descmis_req->request,
> + GFP_ATOMIC);
> +}
> +
> +/**
> + * cdns3_check_ep_interrupt_proceed - Processes interrupt related to endpoint
> + * @priv_ep: endpoint object
> + *
> + * Returns 0
> + */
> +static int cdns3_check_ep_interrupt_proceed(struct cdns3_endpoint *priv_ep)
> +{
> + struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
> + u32 ep_sts_reg;
> +
> + cdns3_select_ep(priv_dev, priv_ep->endpoint.address);
> + ep_sts_reg = readl(&priv_dev->regs->ep_sts);
> + writel(ep_sts_reg, &priv_dev->regs->ep_sts);
> +
> + trace_cdns3_epx_irq(priv_ep);
> +
> + if ((ep_sts_reg & EP_STS_IOC) || (ep_sts_reg & EP_STS_ISP))
> + cdns3_transfer_completed(priv_dev, priv_ep);
> +
> + if (ep_sts_reg & EP_STS_DESCMIS)
> + cdns3_descmissing_packet(priv_ep);
> +
> + return 0;
> +}
> +
> +/**
> + * cdns3_check_usb_interrupt_proceed - Processes interrupt related to device
> + * @priv_dev: extended gadget object
> + * @usb_ists: bitmap representation of device's reported interrupts
> + * (usb_ists register value)
> + */
> +static void cdns3_check_usb_interrupt_proceed(struct cdns3_device *priv_dev,
> + u32 usb_ists)
> +{
> + int speed = 0;
> +
> + trace_cdns3_usb_irq(priv_dev, usb_ists);
> + /* Connection detected */
> + if (usb_ists & (USB_ISTS_CON2I | USB_ISTS_CONI)) {
> + speed = cdns3_get_speed(priv_dev);
> + priv_dev->gadget.speed = speed;
> + usb_gadget_set_state(&priv_dev->gadget, USB_STATE_POWERED);
> + cdns3_ep0_config(priv_dev);
> + }
> +
> + /* Disconnection detected */
> + if (usb_ists & (USB_ISTS_DIS2I | USB_ISTS_DISI)) {
> + if (priv_dev->gadget_driver &&
> + priv_dev->gadget_driver->disconnect) {
> + spin_unlock(&priv_dev->lock);
> + priv_dev->gadget_driver->disconnect(&priv_dev->gadget);
> + spin_lock(&priv_dev->lock);
> + }
> +
> + priv_dev->gadget.speed = USB_SPEED_UNKNOWN;
> + usb_gadget_set_state(&priv_dev->gadget, USB_STATE_NOTATTACHED);
> + cdns3_gadget_unconfig(priv_dev);
> + }
> +
> + /* reset*/
> + if (usb_ists & (USB_ISTS_UWRESI | USB_ISTS_UHRESI | USB_ISTS_U2RESI)) {
> + /*read again to check the actuall speed*/
> + speed = cdns3_get_speed(priv_dev);
> + usb_gadget_set_state(&priv_dev->gadget, USB_STATE_DEFAULT);
> + priv_dev->gadget.speed = speed;
> + cdns3_gadget_unconfig(priv_dev);
> + cdns3_ep0_config(priv_dev);
> + }
> +}
> +
> +/**
> + * cdns3_device_irq_handler- interrupt handler for device part of controller
> + *
> + * @irq: irq number for cdns3 core device
> + * @data: structure of cdns3
> + *
> + * Returns IRQ_HANDLED or IRQ_NONE
> + */
> +static irqreturn_t cdns3_device_irq_handler(int irq, void *data)
> +{
> + struct cdns3_device *priv_dev;
> + struct cdns3 *cdns = data;
> + irqreturn_t ret = IRQ_NONE;
> + unsigned long flags;
> + u32 reg;
> +
> + priv_dev = cdns->gadget_dev;
> + spin_lock_irqsave(&priv_dev->lock, flags);
> +
> + /* check USB device interrupt */
> + reg = readl(&priv_dev->regs->usb_ists);
> + writel(reg, &priv_dev->regs->usb_ists);
> +
> + if (reg) {
> + dev_dbg(priv_dev->dev, "IRQ: usb_ists: %08X\n", reg);
> + cdns3_check_usb_interrupt_proceed(priv_dev, reg);
> + ret = IRQ_HANDLED;
> + }
> +
> + /* check endpoint interrupt */
> + reg = readl(&priv_dev->regs->ep_ists);
> +
> + /* handle default endpoint OUT */
> + if (reg & EP_ISTS_EP_OUT0) {
> + cdns3_check_ep0_interrupt_proceed(priv_dev, USB_DIR_OUT);
> + ret = IRQ_HANDLED;
> + }
> +
> + /* handle default endpoint IN */
> + if (reg & EP_ISTS_EP_IN0) {
> + cdns3_check_ep0_interrupt_proceed(priv_dev, USB_DIR_IN);
> + ret = IRQ_HANDLED;
> + }
> +
> + /* check if interrupt from non default endpoint, if no exit */
> + reg &= ~(EP_ISTS_EP_OUT0 | EP_ISTS_EP_IN0);
> + if (!reg)
> + goto irqend;
> +
> + do {
> + unsigned int bit_pos = ffs(reg);
> + u32 bit_mask = 1 << (bit_pos - 1);
> + int index;
> +
> + index = cdns3_ep_reg_pos_to_index(bit_pos);
> + cdns3_check_ep_interrupt_proceed(priv_dev->eps[index]);
> + reg &= ~bit_mask;
> + ret = IRQ_HANDLED;
> + } while (reg);
> +
> +irqend:
> + spin_unlock_irqrestore(&priv_dev->lock, flags);
> + return ret;
> +}
> +
> +/**
> + * cdns3_ep_onchip_buffer_reserve - Try to reserve onchip buf for EP
> + *
> + * The real reservation will occur during write to EP_CFG register,
> + * this function is used to check if the 'size' reservation is allowed.
> + *
> + * @priv_dev: extended gadget object
> + * @size: the size (KB) for EP would like to allocate
> + *
> + * Return 0 if the required size can met or negative value on failure
> + */
> +static int cdns3_ep_onchip_buffer_reserve(struct cdns3_device *priv_dev,
> + int size)
> +{
> + u32 onchip_mem;
> +
> + priv_dev->onchip_mem_allocated_size += size;
> +
> + onchip_mem = USB_CAP2_ACTUAL_MEM_SIZE(readl(&priv_dev->regs->usb_cap2));
> + if (!onchip_mem)
> + onchip_mem = 256;
> +
> + /* 2KB is reserved for EP0*/
> + onchip_mem -= 2;
> + if (priv_dev->onchip_mem_allocated_size > onchip_mem) {
> + priv_dev->onchip_mem_allocated_size -= size;
> + return -EPERM;
> + }
> +
> + return 0;
> +}
> +
> +/**
> + * cdns3_ep_config Configure hardware endpoint
> + * @priv_ep: extended endpoint object
> + */
> +void cdns3_ep_config(struct cdns3_endpoint *priv_ep)
> +{
> + bool is_iso_ep = (priv_ep->type == USB_ENDPOINT_XFER_ISOC);
> + struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
> + u32 bEndpointAddress = priv_ep->num | priv_ep->dir;
> + u32 interrupt_mask = EP_STS_EN_TRBERREN;
> + u32 max_packet_size = 0;
> + u32 ep_cfg = 0;
> + int ret;
> +
> + if (!priv_ep->dir)
> + interrupt_mask |= EP_STS_EN_DESCMISEN;
> +
> + if (priv_ep->type == USB_ENDPOINT_XFER_INT) {
> + ep_cfg = EP_CFG_EPTYPE(USB_ENDPOINT_XFER_INT);
> + } else if (priv_ep->type == USB_ENDPOINT_XFER_BULK) {
> + ep_cfg = EP_CFG_EPTYPE(USB_ENDPOINT_XFER_BULK);
> + } else {
> + ep_cfg = EP_CFG_EPTYPE(USB_ENDPOINT_XFER_ISOC);
> + interrupt_mask = 0xFFFFFFFF;
> + }
> +
> + switch (priv_dev->gadget.speed) {
> + case USB_SPEED_FULL:
> + max_packet_size = is_iso_ep ? 1023 : 64;
> + break;
> + case USB_SPEED_HIGH:
> + max_packet_size = is_iso_ep ? 1024 : 512;
> + break;
> + case USB_SPEED_SUPER:
> + max_packet_size = 1024;
> + break;
> + default:
> + /* all other speed are not supported */
> + return;
> + }
> +
> + ret = cdns3_ep_onchip_buffer_reserve(priv_dev, CDNS3_EP_BUF_SIZE);
> + if (ret) {
> + dev_err(priv_dev->dev, "onchip mem is full, ep is invalid\n");
> + return;
> + }
> +
> + ep_cfg |= EP_CFG_MAXPKTSIZE(max_packet_size) |
> + EP_CFG_BUFFERING(CDNS3_EP_BUF_SIZE - 1) |
> + EP_CFG_MAXBURST(priv_ep->endpoint.maxburst);
> +
> + cdns3_select_ep(priv_dev, bEndpointAddress);
> +
> + writel(ep_cfg, &priv_dev->regs->ep_cfg);
> + writel(interrupt_mask, &priv_dev->regs->ep_sts_en);
> +
> + dev_dbg(priv_dev->dev, "Configure %s: with val %08x\n",
> + priv_ep->name, ep_cfg);
> +
> + /* enable interrupt for selected endpoint */
> + cdns3_set_register_bit(&priv_dev->regs->ep_ien,
> + cdns3_ep_addr_to_bit_pos(bEndpointAddress));
> +}
> +
> +/* Find correct direction for HW endpoint according to description */
> +static int cdns3_ep_dir_is_correct(struct usb_endpoint_descriptor *desc,
> + struct cdns3_endpoint *priv_ep)
> +{
> + return (priv_ep->endpoint.caps.dir_in && usb_endpoint_dir_in(desc)) ||
> + (priv_ep->endpoint.caps.dir_out && usb_endpoint_dir_out(desc));
> +}
> +
> +static struct
> +cdns3_endpoint *cdns3_find_available_ep(struct cdns3_device *priv_dev,
> + struct usb_endpoint_descriptor *desc)
> +{
> + struct usb_ep *ep;
> + struct cdns3_endpoint *priv_ep;
> +
> + list_for_each_entry(ep, &priv_dev->gadget.ep_list, ep_list) {
> + unsigned long num;
> + int ret;
> + /* ep name pattern likes epXin or epXout */
> + char c[2] = {ep->name[2], '\0'};
> +
> + ret = kstrtoul(c, 10, &num);
> + if (ret)
> + return ERR_PTR(ret);
> +
> + priv_ep = ep_to_cdns3_ep(ep);
> + if (cdns3_ep_dir_is_correct(desc, priv_ep)) {
> + if (!(priv_ep->flags & EP_CLAIMED)) {
> + priv_ep->num = num;
> + return priv_ep;
> + }
> + }
> + }
> + return ERR_PTR(-ENOENT);
> +}
> +
> +static struct
> +usb_ep *cdns3_gadget_match_ep(struct usb_gadget *gadget,
> + struct usb_endpoint_descriptor *desc,
> + struct usb_ss_ep_comp_descriptor *comp_desc)
> +{
> + struct cdns3_device *priv_dev = gadget_to_cdns3_device(gadget);
> + struct cdns3_endpoint *priv_ep;
> + unsigned long flags;
> +
> + priv_ep = cdns3_find_available_ep(priv_dev, desc);
> + if (IS_ERR(priv_ep)) {
> + dev_err(priv_dev->dev, "no available ep\n");
> + return NULL;
> + }
> +
> + dev_dbg(priv_dev->dev, "match endpoint: %s\n", priv_ep->name);
> +
> + spin_lock_irqsave(&priv_dev->lock, flags);
> + priv_ep->endpoint.desc = desc;
> + priv_ep->dir = usb_endpoint_dir_in(desc) ? USB_DIR_IN : USB_DIR_OUT;
> + priv_ep->type = usb_endpoint_type(desc);
> + priv_ep->flags |= EP_CLAIMED;
> + spin_unlock_irqrestore(&priv_dev->lock, flags);
> + return &priv_ep->endpoint;
> +}
> +
> +/**
> + * cdns3_gadget_ep_alloc_request Allocates request
> + * @ep: endpoint object associated with request
> + * @gfp_flags: gfp flags
> + *
> + * Returns allocated request address, NULL on allocation error
> + */
> +struct usb_request *cdns3_gadget_ep_alloc_request(struct usb_ep *ep,
> + gfp_t gfp_flags)
> +{
> + struct cdns3_endpoint *priv_ep = ep_to_cdns3_ep(ep);
> + struct cdns3_request *priv_req;
> +
> + priv_req = kzalloc(sizeof(*priv_req), gfp_flags);
> + if (!priv_req)
> + return NULL;
> +
> + priv_req->priv_ep = priv_ep;
> +
> + trace_cdns3_alloc_request(priv_req);
> + return &priv_req->request;
> +}
> +
> +/**
> + * cdns3_gadget_ep_free_request Free memory occupied by request
> + * @ep: endpoint object associated with request
> + * @request: request to free memory
> + */
> +void cdns3_gadget_ep_free_request(struct usb_ep *ep,
> + struct usb_request *request)
> +{
> + struct cdns3_request *priv_req = to_cdns3_request(request);
> +
> + trace_cdns3_free_request(priv_req);
> + kfree(priv_req);
> +}
> +
> +/**
> + * cdns3_gadget_ep_enable Enable endpoint
> + * @ep: endpoint object
> + * @desc: endpoint descriptor
> + *
> + * Returns 0 on success, error code elsewhere
> + */
> +static int cdns3_gadget_ep_enable(struct usb_ep *ep,
> + const struct usb_endpoint_descriptor *desc)
> +{
> + struct cdns3_endpoint *priv_ep;
> + struct cdns3_device *priv_dev;
> + unsigned long flags;
> + int ret;
> + u32 reg;
> +
> + priv_ep = ep_to_cdns3_ep(ep);
> + priv_dev = priv_ep->cdns3_dev;
> +
> + if (!ep || !desc || desc->bDescriptorType != USB_DT_ENDPOINT) {
> + dev_dbg(priv_dev->dev, "usbss: invalid parameters\n");
> + return -EINVAL;
> + }
> +
> + if (!desc->wMaxPacketSize) {
> + dev_err(priv_dev->dev, "usbss: missing wMaxPacketSize\n");
> + return -EINVAL;
> + }
> +
> + if (dev_WARN_ONCE(priv_dev->dev, priv_ep->flags & EP_ENABLED,
> + "%s is already enabled\n", priv_ep->name))
> + return 0;
> +
> + ret = cdns3_allocate_trb_pool(priv_ep);
> + if (ret)
> + return ret;
> +
> + trace_cdns3_gadget_ep_enable(priv_ep);
> + spin_lock_irqsave(&priv_dev->lock, flags);
> +
> + priv_ep->endpoint.desc = desc;
> + priv_ep->dir = usb_endpoint_dir_in(desc) ? USB_DIR_IN : USB_DIR_OUT;
> + priv_ep->type = usb_endpoint_type(desc);
> +
> + cdns3_select_ep(priv_dev, desc->bEndpointAddress);
> + writel(EP_CMD_EPRST, &priv_dev->regs->ep_cmd);
> +
> + ret = cdns3_handshake(&priv_dev->regs->ep_cmd,
> + EP_CMD_CSTALL | EP_CMD_EPRST, 0, 100);
> +
> + cdns3_set_register_bit(&priv_dev->regs->ep_cfg, EP_CFG_ENABLE);
> +
> + ep->desc = desc;
> + priv_ep->flags &= ~(EP_PENDING_REQUEST | EP_STALL);
> + priv_ep->flags |= EP_ENABLED | EP_UPDATE_EP_TRBADDR;
> + priv_ep->enqueue = 0;
> + priv_ep->dequeue = 0;
> + reg = readl(&priv_dev->regs->ep_sts);
> + priv_ep->pcs = !!EP_STS_CCS(reg);
> + priv_ep->ccs = !!EP_STS_CCS(reg);
> + /* one TRB is reserved for link TRB used in DMULT mode*/
> + priv_ep->free_trbs = TRBS_PER_SEGMENT - 1;
> +
> + spin_unlock_irqrestore(&priv_dev->lock, flags);
> + return 0;
> +}
> +
> +/**
> + * cdns3_gadget_ep_disable Disable endpoint
> + * @ep: endpoint object
> + *
> + * Returns 0 on success, error code elsewhere
> + */
> +static int cdns3_gadget_ep_disable(struct usb_ep *ep)
> +{
> + struct cdns3_endpoint *priv_ep;
> + struct cdns3_device *priv_dev;
> + unsigned long flags;
> + int ret = 0;
> + struct usb_request *request;
> + u32 ep_cfg;
> +
> + if (!ep) {
> + dev_dbg(priv_dev->dev, "usbss: invalid parameters\n");
> + return -EINVAL;
> + }
> +
> + priv_ep = ep_to_cdns3_ep(ep);
> + priv_dev = priv_ep->cdns3_dev;
> +
> + if (dev_WARN_ONCE(priv_dev->dev, !(priv_ep->flags & EP_ENABLED),
> + "%s is already disabled\n", priv_ep->name))
> + return 0;
> +
> + spin_lock_irqsave(&priv_dev->lock, flags);
> +
> + trace_cdns3_gadget_ep_disable(priv_ep);
> +
> + cdns3_select_ep(priv_dev, ep->desc->bEndpointAddress);
> + ret = cdns3_data_flush(priv_ep);
> +
> + ep_cfg = readl(&priv_dev->regs->ep_cfg);
> + ep_cfg &= ~EP_CFG_ENABLE;
> + writel(ep_cfg, &priv_dev->regs->ep_cfg);
> +
> + while (!list_empty(&priv_ep->request_list)) {
> + request = cdns3_next_request(&priv_ep->request_list);
> +
> + cdns3_gadget_giveback(priv_ep, to_cdns3_request(request),
> + -ESHUTDOWN);
> + }
> +
> + if (priv_ep->descmis_req) {
> + kfree(priv_ep->descmis_req->request.buf);
> + cdns3_gadget_ep_free_request(&priv_ep->endpoint,
> + &priv_ep->descmis_req->request);
> + priv_ep->descmis_req = NULL;
> + priv_ep->descmis_pending = false;
> + priv_ep->descmis_finished = false;
> + }
> +
> + ep->desc = NULL;
> + priv_ep->flags &= ~EP_ENABLED;
> +
> + spin_unlock_irqrestore(&priv_dev->lock, flags);
> +
> + return ret;
> +}
> +
> +/**
> + * cdns3_gadget_ep_queue Transfer data on endpoint
> + * @ep: endpoint object
> + * @request: request object
> + * @gfp_flags: gfp flags
> + *
> + * Returns 0 on success, error code elsewhere
> + */
> +static int __cdns3_gadget_ep_queue(struct usb_ep *ep,
> + struct usb_request *request,
> + gfp_t gfp_flags)
> +{
> + struct cdns3_endpoint *priv_ep = ep_to_cdns3_ep(ep);
> + struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
> + struct cdns3_request *priv_req;
> + int ret = 0;
> +
> + request->actual = 0;
> + request->status = -EINPROGRESS;
> + priv_req = to_cdns3_request(request);
> +
> + trace_cdns3_ep_queue(priv_req);
> +
> + /* Data will be copied from internal usb_request object. */
> + if (priv_ep->descmis_finished) {
> + priv_ep->descmis_finished = false;
> + request->actual = priv_ep->descmis_req->request.actual;
> +
> + memcpy(request->buf, priv_ep->descmis_req->request.buf,
> + priv_ep->descmis_req->request.actual);
> + list_add_tail(&request->list, &priv_ep->request_list);
> +
> + cdns3_gadget_giveback(priv_ep,
> + priv_req,
> + priv_ep->descmis_req->request.status);
> +
> + return ret;
> + }
> +
> + ret = usb_gadget_map_request_by_dev(priv_dev->sysdev, request,
> + usb_endpoint_dir_in(ep->desc));
> + if (ret)
> + return ret;
> +
> + list_add_tail(&request->list, &priv_ep->request_list);
> +
> + cdns3_ep_run_transfer(priv_ep, request);
> +
> + return ret;
> +}
> +
> +static int cdns3_gadget_ep_queue(struct usb_ep *ep, struct usb_request *request,
> + gfp_t gfp_flags)
> +{
> + struct cdns3_endpoint *priv_ep = ep_to_cdns3_ep(ep);
> + struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
> + struct usb_request *zlp_request;
> + unsigned long flags;
> + int ret;
> +
> + if (!request || !ep)
> + return -EINVAL;
> +
> + spin_lock_irqsave(&priv_dev->lock, flags);
> + ret = __cdns3_gadget_ep_queue(ep, request, gfp_flags);
> +
> + if (ret == 0 && request->zero && request->length &&
> + (request->length % ep->maxpacket == 0)) {
> + struct cdns3_request *priv_req;
> +
> + zlp_request = cdns3_gadget_ep_alloc_request(ep, GFP_ATOMIC);
> + zlp_request->buf = priv_dev->zlp_buf;
> + zlp_request->length = 0;
> +
> + priv_req = to_cdns3_request(zlp_request);
> + priv_req->flags |= REQUEST_ZLP;
> +
> + dev_dbg(priv_dev->dev, "Queuing ZLP for endpoint: %s\n",
> + priv_ep->name);
> + ret = __cdns3_gadget_ep_queue(ep, zlp_request, gfp_flags);
> + }
> +
> + spin_unlock_irqrestore(&priv_dev->lock, flags);
> + return ret;
> +}
> +
> +/**
> + * cdns3_gadget_ep_dequeue Remove request from transfer queue
> + * @ep: endpoint object associated with request
> + * @request: request object
> + *
> + * Returns 0 on success, error code elsewhere
> + */
> +int cdns3_gadget_ep_dequeue(struct usb_ep *ep,
> + struct usb_request *request)
> +{
> + struct cdns3_endpoint *priv_ep = ep_to_cdns3_ep(ep);
> + struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
> + struct usb_request *req, *req_temp;
> + struct cdns3_request *priv_req;
> + unsigned long flags;
> + int ret = 0;
> +
> + if (!ep || !request || !ep->desc)
> + return -EINVAL;
> +
> + spin_lock_irqsave(&priv_dev->lock, flags);
> +
> + priv_req = to_cdns3_request(request);
> +
> + trace_cdns3_ep_dequeue(priv_req);
> +
> + cdns3_select_ep(priv_dev, ep->desc->bEndpointAddress);
> +
> + list_for_each_entry_safe(req, req_temp, &priv_ep->request_list, list) {
> + if (request == req) {
> + cdns3_gadget_giveback(priv_ep,
> + priv_req,
> + -ECONNRESET);
> + break;
> + }
> + }
> +
> + spin_unlock_irqrestore(&priv_dev->lock, flags);
> + return ret;
> +}
> +
> +/**
> + * cdns3_gadget_ep_set_halt Sets/clears stall on selected endpoint
> + * @ep: endpoint object to set/clear stall on
> + * @value: 1 for set stall, 0 for clear stall
> + *
> + * Returns 0 on success, error code elsewhere
> + */
> +int cdns3_gadget_ep_set_halt(struct usb_ep *ep, int value)
> +{
> + struct cdns3_endpoint *priv_ep = ep_to_cdns3_ep(ep);
> + struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
> + unsigned long flags;
> + int ret = 0;
> +
> + if (!(priv_ep->flags & EP_ENABLED))
> + return -EPERM;
> +
> + spin_lock_irqsave(&priv_dev->lock, flags);
> +
> + /* if actual transfer is pending defer setting stall on this endpoint */
> + if ((priv_ep->flags & EP_PENDING_REQUEST) && value) {
> + priv_ep->flags |= EP_STALL;
> + goto finish;
> + }
> +
> + dev_dbg(priv_dev->dev, "Halt endpoint %s\n", priv_ep->name);
> +
> + cdns3_select_ep(priv_dev, ep->desc->bEndpointAddress);
> + if (value) {
> + cdns3_ep_stall_flush(priv_ep);
> + } else {
> + priv_ep->flags &= ~EP_WEDGE;
> + writel(EP_CMD_CSTALL | EP_CMD_EPRST, &priv_dev->regs->ep_cmd);
> +
> + /* wait for EPRST cleared */
> + ret = cdns3_handshake(&priv_dev->regs->ep_cmd,
> + EP_CMD_EPRST, 0, 100);
> + if (unlikely(ret)) {
> + dev_err(priv_dev->dev,
> + "Clearing halt condition failed for %s\n",
> + priv_ep->name);
> + goto finish;
> +
> + } else {
> + priv_ep->flags &= ~EP_STALL;
> + }
> + }
> +
> + priv_ep->flags &= ~EP_PENDING_REQUEST;
> +finish:
> + spin_unlock_irqrestore(&priv_dev->lock, flags);
> +
> + return ret;
> +}
> +
> +extern const struct usb_ep_ops cdns3_gadget_ep0_ops;
> +
> +static const struct usb_ep_ops cdns3_gadget_ep_ops = {
> + .enable = cdns3_gadget_ep_enable,
> + .disable = cdns3_gadget_ep_disable,
> + .alloc_request = cdns3_gadget_ep_alloc_request,
> + .free_request = cdns3_gadget_ep_free_request,
> + .queue = cdns3_gadget_ep_queue,
> + .dequeue = cdns3_gadget_ep_dequeue,
> + .set_halt = cdns3_gadget_ep_set_halt,
> + .set_wedge = cdns3_gadget_ep_set_wedge,
> +};
> +
> +/**
> + * cdns3_gadget_get_frame Returns number of actual ITP frame
> + * @gadget: gadget object
> + *
> + * Returns number of actual ITP frame
> + */
> +static int cdns3_gadget_get_frame(struct usb_gadget *gadget)
> +{
> + struct cdns3_device *priv_dev = gadget_to_cdns3_device(gadget);
> +
> + return readl(&priv_dev->regs->usb_iptn);
> +}
> +
> +static int cdns3_gadget_wakeup(struct usb_gadget *gadget)
> +{
> + return 0;
> +}
> +
> +static int cdns3_gadget_set_selfpowered(struct usb_gadget *gadget,
> + int is_selfpowered)
> +{
> + struct cdns3_device *priv_dev = gadget_to_cdns3_device(gadget);
> + unsigned long flags;
> +
> + spin_lock_irqsave(&priv_dev->lock, flags);
> + priv_dev->is_selfpowered = !!is_selfpowered;
> + spin_unlock_irqrestore(&priv_dev->lock, flags);
> + return 0;
> +}
> +
> +static int cdns3_gadget_pullup(struct usb_gadget *gadget, int is_on)
> +{
> + struct cdns3_device *priv_dev = gadget_to_cdns3_device(gadget);
> +
> + if (is_on)
> + writel(USB_CONF_DEVEN, &priv_dev->regs->usb_conf);
> + else
> + writel(USB_CONF_DEVDS, &priv_dev->regs->usb_conf);
> +
> + return 0;
> +}
> +
> +static void cdns3_gadget_config(struct cdns3_device *priv_dev)
> +{
> + struct cdns3_usb_regs __iomem *regs = priv_dev->regs;
> +
> + cdns3_ep0_config(priv_dev);
> +
> + /* enable interrupts for endpoint 0 (in and out) */
> + writel(EP_IEN_EP_OUT0 | EP_IEN_EP_IN0, &regs->ep_ien);
> +
> + /* enable generic interrupt*/
> + writel(USB_IEN_INIT, &regs->usb_ien);
> + writel(USB_CONF_CLK2OFFDS | USB_CONF_L1DS, &regs->usb_conf);
> + writel(USB_CONF_DMULT, &regs->usb_conf);
> + writel(USB_CONF_DEVEN, &regs->usb_conf);
> +}
> +
> +/**
> + * cdns3_gadget_udc_start Gadget start
> + * @gadget: gadget object
> + * @driver: driver which operates on this gadget
> + *
> + * Returns 0 on success, error code elsewhere
> + */
> +static int cdns3_gadget_udc_start(struct usb_gadget *gadget,
> + struct usb_gadget_driver *driver)
> +{
> + struct cdns3_device *priv_dev = gadget_to_cdns3_device(gadget);
> + unsigned long flags;
> +
> + spin_lock_irqsave(&priv_dev->lock, flags);
> + priv_dev->gadget_driver = driver;
> + cdns3_gadget_config(priv_dev);
> + spin_unlock_irqrestore(&priv_dev->lock, flags);
> + return 0;
> +}
> +
> +/**
> + * cdns3_gadget_udc_stop Stops gadget
> + * @gadget: gadget object
> + *
> + * Returns 0
> + */
> +static int cdns3_gadget_udc_stop(struct usb_gadget *gadget)
> +{
> + struct cdns3_device *priv_dev = gadget_to_cdns3_device(gadget);
> + struct cdns3_endpoint *priv_ep;
> + u32 bEndpointAddress;
> + struct usb_ep *ep;
> + int ret = 0;
> + int i;
> +
> + priv_dev->gadget_driver = NULL;
> +
> + priv_dev->onchip_mem_allocated_size = 0;
> + priv_dev->gadget.speed = USB_SPEED_UNKNOWN;
> +
> + for (i = 0; i < priv_dev->ep_nums ; i++)
> + cdns3_free_trb_pool(priv_dev->eps[i]);
> +
> + list_for_each_entry(ep, &priv_dev->gadget.ep_list, ep_list) {
> + priv_ep = ep_to_cdns3_ep(ep);
> + bEndpointAddress = priv_ep->num | priv_ep->dir;
> + cdns3_select_ep(priv_dev, bEndpointAddress);
> + writel(EP_CMD_EPRST, &priv_dev->regs->ep_cmd);
> + ret = cdns3_handshake(&priv_dev->regs->ep_cmd,
> + EP_CMD_EPRST, 0, 100);
> + }
> +
> + /* disable interrupt for device */
> + writel(0, &priv_dev->regs->usb_ien);
> + writel(USB_CONF_DEVDS, &priv_dev->regs->usb_conf);
> +
> + return ret;
> +}
> +
> +static const struct usb_gadget_ops cdns3_gadget_ops = {
> + .get_frame = cdns3_gadget_get_frame,
> + .wakeup = cdns3_gadget_wakeup,
> + .set_selfpowered = cdns3_gadget_set_selfpowered,
> + .pullup = cdns3_gadget_pullup,
> + .udc_start = cdns3_gadget_udc_start,
> + .udc_stop = cdns3_gadget_udc_stop,
> + .match_ep = cdns3_gadget_match_ep,
> +};
> +
> +static void cdns3_free_all_ep(struct cdns3_device *priv_dev)
> +{
> + int i;
> +
> + for (i = 0; i < CDNS3_ENDPOINTS_MAX_COUNT; i++)
> + if (priv_dev->eps[i])
> + devm_kfree(priv_dev->dev, priv_dev->eps[i]);
> +
> + if (priv_dev->gadget.ep0)
> + devm_kfree(priv_dev->dev, priv_dev->gadget.ep0);
> +}
> +
> +/**
> + * cdns3_init_ep Initializes software endpoints of gadget
> + * @cdns3: extended gadget object
> + *
> + * Returns 0 on success, error code elsewhere
> + */
> +static int cdns3_init_ep(struct cdns3_device *priv_dev)
> +{
> + u32 ep_enabled_reg, iso_ep_reg;
> + struct cdns3_endpoint *priv_ep;
> + int found_endpoints = 0;
> + int ep_dir, ep_number;
> + u32 ep_mask;
> + int i;
> +
> + /* Read it from USB_CAP3 to USB_CAP5 */
> + ep_enabled_reg = readl(&priv_dev->regs->usb_cap3);
> + iso_ep_reg = readl(&priv_dev->regs->usb_cap4);
> +
> + dev_dbg(priv_dev->dev, "Initializing non-zero endpoints\n");
> +
> + for (i = 0; i < CDNS3_ENDPOINTS_MAX_COUNT; i++) {
> + ep_number = (i / 2) + 1;
> + ep_dir = i % 2;
> + ep_mask = BIT((16 * ep_dir) + ep_number);
> +
> + if (!(ep_enabled_reg & ep_mask))
> + continue;
> +
> + priv_ep = devm_kzalloc(priv_dev->dev, sizeof(*priv_ep),
> + GFP_KERNEL);
> + if (!priv_ep)
> + return -ENOMEM;
> +
> + /* set parent of endpoint object */
> + priv_ep->cdns3_dev = priv_dev;
> + priv_dev->eps[found_endpoints++] = priv_ep;
> +
> + snprintf(priv_ep->name, sizeof(priv_ep->name), "ep%d%s",
> + ep_number, !!ep_dir ? "in" : "out");
> + priv_ep->endpoint.name = priv_ep->name;
> +
> + usb_ep_set_maxpacket_limit(&priv_ep->endpoint,
> + CDNS3_EP_MAX_PACKET_LIMIT);
> + priv_ep->endpoint.max_streams = CDNS3_EP_MAX_STREAMS;
> + priv_ep->endpoint.ops = &cdns3_gadget_ep_ops;
> + if (ep_dir)
> + priv_ep->endpoint.caps.dir_in = 1;
> + else
> + priv_ep->endpoint.caps.dir_out = 1;
> +
> + if (iso_ep_reg & ep_mask)
> + priv_ep->endpoint.caps.type_iso = 1;
> +
> + priv_ep->endpoint.caps.type_bulk = 1;
> + priv_ep->endpoint.caps.type_int = 1;
> + priv_ep->endpoint.maxburst = CDNS3_EP_BUF_SIZE - 1;
> +
> + priv_ep->flags = 0;
> +
> + dev_info(priv_dev->dev, "Initialized %s support: %s %s\n",
> + priv_ep->name,
> + priv_ep->endpoint.caps.type_bulk ? "BULK, INT" : "",
> + priv_ep->endpoint.caps.type_iso ? "ISO" : "");
> +
> + list_add_tail(&priv_ep->endpoint.ep_list,
> + &priv_dev->gadget.ep_list);
> + INIT_LIST_HEAD(&priv_ep->request_list);
> + }
> +
> + priv_dev->ep_nums = found_endpoints;
> + return 0;
> +}
> +
> +static void cdns3_gadget_disable(struct cdns3 *cdns)
> +{
> + struct cdns3_device *priv_dev;
> +
> + priv_dev = cdns->gadget_dev;
> +
> + if (priv_dev->gadget_driver)
> + priv_dev->gadget_driver->disconnect(&priv_dev->gadget);
> +
> + usb_gadget_disconnect(&priv_dev->gadget);
> + priv_dev->gadget.speed = USB_SPEED_UNKNOWN;
> +}
> +
> +void cdns3_gadget_exit(struct cdns3 *cdns)
> +{
> + struct cdns3_device *priv_dev;
> +
> + priv_dev = cdns->gadget_dev;
> +
> + cdns3_gadget_disable(cdns);
> +
> + devm_free_irq(cdns->dev, cdns->irq, cdns);
> +
> + pm_runtime_mark_last_busy(cdns->dev);
> + pm_runtime_put_autosuspend(cdns->dev);
> +
> + usb_del_gadget_udc(&priv_dev->gadget);
> +
> + cdns3_free_all_ep(priv_dev);
> +
> + dma_free_coherent(priv_dev->sysdev, 8, priv_dev->setup_buf,
> + priv_dev->setup_dma);
> + dma_free_coherent(priv_dev->sysdev, TRB_SIZE * 2, priv_dev->ep0_trb,
> + priv_dev->ep0_trb_dma);
> +
> + kfree(priv_dev->zlp_buf);
> + kfree(priv_dev);
> + cdns->gadget_dev = NULL;
> +}
> +
> +static int cdns3_gadget_start(struct cdns3 *cdns)
> +{
> + struct cdns3_device *priv_dev;
> + u32 max_speed;
> + int ret;
> +
> + priv_dev = kzalloc(sizeof(*priv_dev), GFP_KERNEL);
> + if (!priv_dev)
> + return -ENOMEM;
> +
> + cdns->gadget_dev = priv_dev;
> + priv_dev->sysdev = cdns->dev;
> + priv_dev->dev = cdns->dev;
> + priv_dev->regs = cdns->dev_regs;
> +
> + max_speed = usb_get_maximum_speed(cdns->dev);
> +
> + /* Check the maximum_speed parameter */
> + switch (max_speed) {
> + case USB_SPEED_FULL:
> + case USB_SPEED_HIGH:
> + case USB_SPEED_SUPER:
> + break;
> + default:
> + dev_err(cdns->dev, "invalid maximum_speed parameter %d\n",
> + max_speed);
> + /* fall through */
> + case USB_SPEED_UNKNOWN:
> + /* default to superspeed */
> + max_speed = USB_SPEED_SUPER;
> + break;
> + }
> +
> + /* fill gadget fields */
> + priv_dev->gadget.max_speed = max_speed;
> + priv_dev->gadget.speed = USB_SPEED_UNKNOWN;
> + priv_dev->gadget.ops = &cdns3_gadget_ops;
> + priv_dev->gadget.name = "usb-ss-gadget";
> + priv_dev->gadget.sg_supported = 1;
> +
> + spin_lock_init(&priv_dev->lock);
> + INIT_WORK(&priv_dev->pending_status_wq,
> + cdns3_pending_setup_status_handler);
> +
> + /* initialize endpoint container */
> + INIT_LIST_HEAD(&priv_dev->gadget.ep_list);
> +
> + ret = cdns3_init_ep0(priv_dev);
> + if (ret) {
> + dev_err(priv_dev->dev, "Failed to create endpoint 0\n");
> + goto err1;
> + }
> +
> + ret = cdns3_init_ep(priv_dev);
> + if (ret) {
> + dev_err(priv_dev->dev, "Failed to create non zero endpoints\n");
> + goto err1;
> + }
> +
> + /* allocate memory for default endpoint TRB */
> + priv_dev->ep0_trb = dma_alloc_coherent(priv_dev->sysdev, TRB_SIZE * 2,
> + &priv_dev->ep0_trb_dma, GFP_DMA);
> + if (!priv_dev->ep0_trb) {
> + dev_err(priv_dev->dev, "Failed to allocate memory for ep0 TRB\n");
> + ret = -ENOMEM;
> + goto err1;
> + }
> +
> + /* allocate memory for setup packet buffer */
> + priv_dev->setup_buf = dma_alloc_coherent(priv_dev->sysdev, 8,
> + &priv_dev->setup_dma, GFP_DMA);
> + if (!priv_dev->setup_buf) {
> + dev_err(priv_dev->dev, "Failed to allocate memory for SETUP buffer\n");
> + ret = -ENOMEM;
> + goto err2;
> + }
> +
> + dev_dbg(priv_dev->dev, "Device Controller version: %08x\n",
> + readl(&priv_dev->regs->usb_cap6));
> + dev_dbg(priv_dev->dev, "USB Capabilities:: %08x\n",
> + readl(&priv_dev->regs->usb_cap1));
> + dev_dbg(priv_dev->dev, "On-Chip memory cnfiguration: %08x\n",
> + readl(&priv_dev->regs->usb_cap2));
> +
> + priv_dev->zlp_buf = kzalloc(CDNS3_EP_ZLP_BUF_SIZE, GFP_KERNEL);
> + if (!priv_dev->zlp_buf) {
> + ret = -ENOMEM;
> + goto err3;
> + }
> +
> + /* add USB gadget device */
> + ret = usb_add_gadget_udc(priv_dev->dev, &priv_dev->gadget);
> + if (ret < 0) {
> + dev_err(priv_dev->dev,
> + "Failed to register USB device controller\n");
> + goto err4;
> + }
> +
> + return 0;
> +err4:
> + kfree(priv_dev->zlp_buf);
> +err3:
> + dma_free_coherent(priv_dev->sysdev, 8, priv_dev->setup_buf,
> + priv_dev->setup_dma);
> +err2:
> + dma_free_coherent(priv_dev->sysdev, TRB_SIZE * 2, priv_dev->ep0_trb,
> + priv_dev->ep0_trb_dma);
> +err1:
> + cdns->gadget_dev = NULL;
> + return ret;
> +}
> +
> +static int __cdns3_gadget_init(struct cdns3 *cdns)
> +{
> + struct cdns3_device *priv_dev;
> + unsigned long flags;
> + int ret = 0;
> +
> + ret = cdns3_gadget_start(cdns);
> + if (ret)
> + return ret;
> +
> + priv_dev = cdns->gadget_dev;
> + ret = devm_request_irq(cdns->dev, cdns->irq, cdns3_device_irq_handler,
> + IRQF_SHARED, dev_name(cdns->dev), cdns);
> +
> + if (ret)
> + goto err0;
> +
> + pm_runtime_get_sync(cdns->dev);
> + spin_lock_irqsave(&priv_dev->lock, flags);
> + spin_unlock_irqrestore(&priv_dev->lock, flags);
> + return 0;
> +err0:
> + cdns3_gadget_exit(cdns);
> + return ret;
> +}
> +
> +static int cdns3_gadget_suspend(struct cdns3 *cdns, bool do_wakeup)
> +{
> + cdns3_gadget_disable(cdns);
> + return 0;
> +}
> +
> +static int cdns3_gadget_resume(struct cdns3 *cdns, bool hibernated)
> +{
> + struct cdns3_device *priv_dev;
> + unsigned long flags;
> +
> + priv_dev = cdns->gadget_dev;
> + spin_lock_irqsave(&priv_dev->lock, flags);
> +
> + if (!priv_dev->gadget_driver) {
> + spin_unlock_irqrestore(&priv_dev->lock, flags);
> + return 0;
> + }
> +
> + cdns3_gadget_config(priv_dev);
> + spin_unlock_irqrestore(&priv_dev->lock, flags);
> + return 0;
> +}
> +
> +/**
> + * cdns3_gadget_init - initialize device structure
> + *
> + * cdns: cdns3 instance
> + *
> + * This function initializes the gadget.
> + */
> +int cdns3_gadget_init(struct cdns3 *cdns)
> +{
> + struct cdns3_role_driver *rdrv;
> +
> + rdrv = devm_kzalloc(cdns->dev, sizeof(*rdrv), GFP_KERNEL);
> + if (!rdrv)
> + return -ENOMEM;
> +
> + rdrv->start = __cdns3_gadget_init;
> + rdrv->stop = cdns3_gadget_exit;
> + rdrv->suspend = cdns3_gadget_suspend;
> + rdrv->resume = cdns3_gadget_resume;
> + rdrv->state = CDNS3_ROLE_STATE_INACTIVE;
> + rdrv->name = "gadget";
> + cdns->roles[CDNS3_ROLE_GADGET] = rdrv;
> +
> + return 0;
> +}
> diff --git a/drivers/usb/cdns3/gadget.h b/drivers/usb/cdns3/gadget.h
> new file mode 100644
> index 000000000000..db398dff65fc
> --- /dev/null
> +++ b/drivers/usb/cdns3/gadget.h
> @@ -0,0 +1,1177 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * USBSS device controller driver header file
> + *
> + * Copyright (C) 2018 Cadence.
> + * Copyright (C) 2017-2018 NXP
> + *
> + * Author: Pawel Laszczak <[email protected]>
> + * Pawel Jez <[email protected]>
> + * Peter Chen <[email protected]>
> + */
> +#ifndef __LINUX_CDNS3_GADGET
> +#define __LINUX_CDNS3_GADGET
> +#include <linux/usb/gadget.h>
> +
> +/*
> + * USBSS-DEV register interface.
> + * This corresponds to the USBSS Device Controller Interface
> + */
> +
> +/**
> + * struct cdns3_usb_regs - device controller registers.
> + * @usb_conf: Global Configuration Register.
> + * @usb_sts: Global Status Register.
> + * @usb_cmd: Global Command Register.
> + * @usb_iptn: ITP/SOF number Register.
> + * @usb_lpm: Global Command Register.
> + * @usb_ien: USB Interrupt Enable Register.
> + * @usb_ists: USB Interrupt Status Register.
> + * @ep_sel: Endpoint Select Register.
> + * @ep_traddr: Endpoint Transfer Ring Address Register.
> + * @ep_cfg: Endpoint Configuration Register.
> + * @ep_cmd: Endpoint Command Register.
> + * @ep_sts: Endpoint Status Register.
> + * @ep_sts_sid: Endpoint Status Register.
> + * @ep_sts_en: Endpoint Status Register Enable.
> + * @drbl: Doorbell Register.
> + * @ep_ien: EP Interrupt Enable Register.
> + * @ep_ists: EP Interrupt Status Register.
> + * @usb_pwr: Global Power Configuration Register.
> + * @usb_conf2: Global Configuration Register 2.
> + * @usb_cap1: Capability Register 1.
> + * @usb_cap2: Capability Register 2.
> + * @usb_cap3: Capability Register 3.
> + * @usb_cap4: Capability Register 4.
> + * @usb_cap5: Capability Register 5.
> + * @usb_cap6: Capability Register 6.
> + * @usb_cpkt1: Custom Packet Register 1.
> + * @usb_cpkt2: Custom Packet Register 2.
> + * @usb_cpkt3: Custom Packet Register 3.
> + * @reserved1: Reserved.
> + * @cfg_regs: Configuration registers.
> + * @reserved2: Reserved.
> + * @dma_axi_ctrl: AXI Control register.
> + * @dma_axi_id: AXI ID register.
> + * @dma_axi_cap: AXI Capability register.
> + * @dma_axi_ctrl0: AXI Control 0 register.
> + * @dma_axi_ctrl1: AXI Control 1 register.
> + */
> +struct cdns3_usb_regs {
> + __le32 usb_conf;
> + __le32 usb_sts;
> + __le32 usb_cmd;
> + __le32 usb_iptn;
> + __le32 usb_lpm;
> + __le32 usb_ien;
> + __le32 usb_ists;
> + __le32 ep_sel;
> + __le32 ep_traddr;
> + __le32 ep_cfg;
> + __le32 ep_cmd;
> + __le32 ep_sts;
> + __le32 ep_sts_sid;
> + __le32 ep_sts_en;
> + __le32 drbl;
> + __le32 ep_ien;
> + __le32 ep_ists;
> + __le32 usb_pwr;
> + __le32 usb_conf2;
> + __le32 usb_cap1;
> + __le32 usb_cap2;
> + __le32 usb_cap3;
> + __le32 usb_cap4;
> + __le32 usb_cap5;
> + __le32 usb_cap6;
> + __le32 usb_cpkt1;
> + __le32 usb_cpkt2;
> + __le32 usb_cpkt3;
> + __le32 reserved1[36];
> + __le32 cfg_reg1;
> + __le32 dbg_link1;
> + __le32 dbg_link2;
> + __le32 cfg_regs[74];
> + __le32 reserved2[34];
> + __le32 dma_axi_ctrl;
> + __le32 dma_axi_id;
> + __le32 dma_axi_cap;
> + __le32 dma_axi_ctrl0;
> + __le32 dma_axi_ctrl1;
> +};
> +
> +/* USB_CONF - bitmasks */
> +/* Reset USB device configuration. */
> +#define USB_CONF_CFGRST BIT(0)
> +/* Set Configuration. */
> +#define USB_CONF_CFGSET BIT(1)
> +/* Disconnect USB device in SuperSpeed. */
> +#define USB_CONF_USB3DIS BIT(3)
> +/* Disconnect USB device in HS/FS */
> +#define USB_CONF_USB2DIS BIT(4)
> +/* Little Endian access - default */
> +#define USB_CONF_LENDIAN BIT(5)
> +/*
> + * Big Endian access. Driver assume that byte order for
> + * SFRs access always is as Little Endian so this bit
> + * is not used.
> + */
> +#define USB_CONF_BENDIAN BIT(6)
> +/* Device software reset. */
> +#define USB_CONF_SWRST BIT(7)
> +/* Singular DMA transfer mode. */
> +#define USB_CONF_DSING BIT(8)
> +/* Multiple DMA transfers mode. */
> +#define USB_CONF_DMULT BIT(9)
> +/* DMA clock turn-off enable. */
> +#define USB_CONF_DMAOFFEN BIT(10)
> +/* DMA clock turn-off disable. */
> +#define USB_CONF_DMAOFFDS BIT(11)
> +/* Clear Force Full Speed. */
> +#define USB_CONF_CFORCE_FS BIT(12)
> +/* Set Force Full Speed. */
> +#define USB_CONF_SFORCE_FS BIT(13)
> +/* Device enable. */
> +#define USB_CONF_DEVEN BIT(14)
> +/* Device disable. */
> +#define USB_CONF_DEVDS BIT(15)
> +/* L1 LPM state entry enable (used in HS/FS mode). */
> +#define USB_CONF_L1EN BIT(16)
> +/* L1 LPM state entry disable (used in HS/FS mode). */
> +#define USB_CONF_L1DS BIT(17)
> +/* USB 2.0 clock gate disable. */
> +#define USB_CONF_CLK2OFFEN BIT(18)
> +/* USB 2.0 clock gate enable. */
> +#define USB_CONF_CLK2OFFDS BIT(19)
> +/* L0 LPM state entry request (used in HS/FS mode). */
> +#define USB_CONF_LGO_L0 BIT(20)
> +/* USB 3.0 clock gate disable. */
> +#define USB_CONF_CLK3OFFEN BIT(21)
> +/* USB 3.0 clock gate enable. */
> +#define USB_CONF_CLK3OFFDS BIT(22)
> +/* Bit 23 is reserved*/
> +/* U1 state entry enable (used in SS mode). */
> +#define USB_CONF_U1EN BIT(24)
> +/* U1 state entry disable (used in SS mode). */
> +#define USB_CONF_U1DS BIT(25)
> +/* U2 state entry enable (used in SS mode). */
> +#define USB_CONF_U2EN BIT(26)
> +/* U2 state entry disable (used in SS mode). */
> +#define USB_CONF_U2DS BIT(27)
> +/* U0 state entry request (used in SS mode). */
> +#define USB_CONF_LGO_U0 BIT(28)
> +/* U1 state entry request (used in SS mode). */
> +#define USB_CONF_LGO_U1 BIT(29)
> +/* U2 state entry request (used in SS mode). */
> +#define USB_CONF_LGO_U2 BIT(30)
> +/* SS.Inactive state entry request (used in SS mode) */
> +#define USB_CONF_LGO_SSINACT BIT(31)
> +
> +/* USB_STS - bitmasks */
> +/*
> + * Configuration status.
> + * 1 - device is in the configured state.
> + * 0 - device is not configured.
> + */
> +#define USB_STS_CFGSTS_MASK BIT(0)
> +#define USB_STS_CFGSTS(p) ((p) & USB_STS_CFGSTS_MASK)
> +/*
> + * On-chip memory overflow.
> + * 0 - On-chip memory status OK.
> + * 1 - On-chip memory overflow.
> + */
> +#define USB_STS_OV_MASK BIT(1)
> +#define USB_STS_OV(p) ((p) & USB_STS_OV_MASK)
> +/*
> + * SuperSpeed connection status.
> + * 0 - USB in SuperSpeed mode disconnected.
> + * 1 - USB in SuperSpeed mode connected.
> + */
> +#define USB_STS_USB3CONS_MASK BIT(2)
> +#define USB_STS_USB3CONS(p) ((p) & USB_STS_USB3CONS_MASK)
> +/*
> + * DMA transfer configuration status.
> + * 0 - single request.
> + * 1 - multiple TRB chain
> + */
> +#define USB_STS_DTRANS_MASK BIT(3)
> +#define USB_STS_DTRANS(p) ((p) & USB_STS_DTRANS_MASK)
> +/*
> + * Device speed.
> + * 0 - Undefined (value after reset).
> + * 1 - Low speed
> + * 2 - Full speed
> + * 3 - High speed
> + * 4 - Super speed
> + */
> +#define USB_STS_USBSPEED_MASK GENMASK(6, 4)
> +#define USB_STS_USBSPEED(p) (((p) & USB_STS_USBSPEED_MASK) >> 4)
> +#define USB_STS_LS (0x1 << 4)
> +#define USB_STS_FS (0x2 << 4)
> +#define USB_STS_HS (0x3 << 4)
> +#define USB_STS_SS (0x4 << 4)
> +#define DEV_UNDEFSPEED(p) (((p) & USB_STS_USBSPEED_MASK) == (0x0 << 4))
> +#define DEV_LOWSPEED(p) (((p) & USB_STS_USBSPEED_MASK) == USB_STS_LS)
> +#define DEV_FULLSPEED(p) (((p) & USB_STS_USBSPEED_MASK) == USB_STS_FS)
> +#define DEV_HIGHSPEED(p) (((p) & USB_STS_USBSPEED_MASK) == USB_STS_HS)
> +#define DEV_SUPERSPEED(p) (((p) & USB_STS_USBSPEED_MASK) == USB_STS_SS)
> +/*
> + * Endianness for SFR access.
> + * 0 - Little Endian order (default after hardware reset).
> + * 1 - Big Endian order
> + */
> +#define USB_STS_ENDIAN_MASK BIT(7)
> +#define USB_STS_ENDIAN(p) ((p) & USB_STS_ENDIAN_MASK)
> +/*
> + * HS/FS clock turn-off status.
> + * 0 - hsfs clock is always on.
> + * 1 - hsfs clock turn-off in L2 (HS/FS mode) is enabled
> + * (default after hardware reset).
> + */
> +#define USB_STS_CLK2OFF_MASK BIT(8)
> +#define USB_STS_CLK2OFF(p) ((p) & USB_STS_CLK2OFF_MASK)
> +/*
> + * PCLK clock turn-off status.
> + * 0 - pclk clock is always on.
> + * 1 - pclk clock turn-off in U3 (SS mode) is enabled
> + * (default after hardware reset).
> + */
> +#define USB_STS_CLK3OFF_MASK BIT(9)
> +#define USB_STS_CLK3OFF(p) ((p) & USB_STS_CLK3OFF_MASK)
> +/*
> + * Controller in reset state.
> + * 0 - Internal reset is active.
> + * 1 - Internal reset is not active and controller is fully operational.
> + */
> +#define USB_STS_IN_RST_MASK BIT(10)
> +#define USB_STS_IN_RST(p) ((p) & USB_STS_IN_RST_MASK)
> +/*
> + * Device enable Status.
> + * 0 - USB device is disabled (VBUS input is disconnected from internal logic).
> + * 1 - USB device is enabled (VBUS input is connected to the internal logic).
> + */
> +#define USB_STS_DEVS_MASK BIT(14)
> +#define USB_STS_DEVS(p) ((p) & USB_STS_DEVS_MASK)
> +/*
> + * DAddress statuss.
> + * 0 - USB device is default state.
> + * 1 - USB device is at least in address state.
> + */
> +#define USB_STS_ADDRESSED_MASK BIT(15)
> +#define USB_STS_ADDRESSED(p) ((p) & USB_STS_ADDRESSED_MASK)
> +/*
> + * L1 LPM state enable status (used in HS/FS mode).
> + * 0 - Entering to L1 LPM state disabled.
> + * 1 - Entering to L1 LPM state enabled.
> + */
> +#define USB_STS_L1ENS_MASK BIT(16)
> +#define USB_STS_L1ENS(p) ((p) & USB_STS_L1ENS_MASK)
> +/*
> + * Internal VBUS connection status (used both in HS/FS and SS mode).
> + * 0 - internal VBUS is not detected.
> + * 1 - internal VBUS is detected.
> + */
> +#define USB_STS_VBUSS_MASK BIT(17)
> +#define USB_STS_VBUSS(p) ((p) & USB_STS_VBUSS_MASK)
> +/*
> + * HS/FS LPM state (used in FS/HS mode).
> + * 0 - L0 State
> + * 1 - L1 State
> + * 2 - L2 State
> + * 3 - L3 State
> + */
> +#define USB_STS_LPMST_MASK GENMASK(19, 18)
> +#define DEV_L0_STATE(p) (((p) & USB_STS_LPMST_MASK) == (0x0 << 18))
> +#define DEV_L1_STATE(p) (((p) & USB_STS_LPMST_MASK) == (0x1 << 18))
> +#define DEV_L2_STATE(p) (((p) & USB_STS_LPMST_MASK) == (0x2 << 18))
> +#define DEV_L3_STATE(p) (((p) & USB_STS_LPMST_MASK) == (0x3 << 18))
> +/*
> + * Disable HS status (used in FS/HS mode).
> + * 0 - the disconnect bit for HS/FS mode is set .
> + * 1 - the disconnect bit for HS/FS mode is not set.
> + */
> +#define USB_STS_USB2CONS_MASK BIT(20)
> +#define USB_STS_USB2CONS(p) ((p) & USB_STS_USB2CONS_MASK)
> +/*
> + * HS/FS mode connection status (used in FS/HS mode).
> + * 0 - High Speed operations in USB2.0 (FS/HS) mode not disabled.
> + * 1 - High Speed operations in USB2.0 (FS/HS).
> + */
> +#define USB_STS_DISABLE_HS_MASK BIT(21)
> +#define USB_STS_DISABLE_HS(p) ((p) & USB_STS_DISABLE_HS_MASK)
> +/*
> + * U1 state enable status (used in SS mode).
> + * 0 - Entering to U1 state disabled.
> + * 1 - Entering to U1 state enabled.
> + */
> +#define USB_STS_U1ENS_MASK BIT(24)
> +#define USB_STS_U1ENS(p) ((p) & USB_STS_U1ENS_MASK)
> +/*
> + * U2 state enable status (used in SS mode).
> + * 0 - Entering to U2 state disabled.
> + * 1 - Entering to U2 state enabled.
> + */
> +#define USB_STS_U2ENS_MASK BIT(25)
> +#define USB_STS_U2ENS(p) ((p) & USB_STS_U2ENS_MASK)
> +/*
> + * SuperSpeed Link LTSSM state. This field reflects USBSS-DEV current
> + * SuperSpeed link state
> + */
> +#define USB_STS_LST_MASK GENMASK(29, 26)
> +#define DEV_LST_U0 (((p) & USB_STS_LST_MASK) == (0x0 << 26))
> +#define DEV_LST_U1 (((p) & USB_STS_LST_MASK) == (0x1 << 26))
> +#define DEV_LST_U2 (((p) & USB_STS_LST_MASK) == (0x2 << 26))
> +#define DEV_LST_U3 (((p) & USB_STS_LST_MASK) == (0x3 << 26))
> +#define DEV_LST_DISABLED (((p) & USB_STS_LST_MASK) == (0x4 << 26))
> +#define DEV_LST_RXDETECT (((p) & USB_STS_LST_MASK) == (0x5 << 26))
> +#define DEV_LST_INACTIVE (((p) & USB_STS_LST_MASK) == (0x6 << 26))
> +#define DEV_LST_POLLING (((p) & USB_STS_LST_MASK) == (0x7 << 26))
> +#define DEV_LST_RECOVERY (((p) & USB_STS_LST_MASK) == (0x8 << 26))
> +#define DEV_LST_HOT_RESET (((p) & USB_STS_LST_MASK) == (0x9 << 26))
> +#define DEV_LST_COMP_MODE (((p) & USB_STS_LST_MASK) == (0xa << 26))
> +#define DEV_LST_LB_STATE (((p) & USB_STS_LST_MASK) == (0xb << 26))
> +/*
> + * DMA clock turn-off status.
> + * 0 - DMA clock is always on (default after hardware reset).
> + * 1 - DMA clock turn-off in U1, U2 and U3 (SS mode) is enabled.
> + */
> +#define USB_STS_DMAOFF_MASK BIT(30)
> +#define USB_STS_DMAOFF(p) ((p) & USB_STS_DMAOFF_MASK)
> +/*
> + * SFR Endian statuss.
> + * 0 - Little Endian order (default after hardware reset).
> + * 1 - Big Endian order.
> + */
> +#define USB_STS_ENDIAN2_MASK BIT(31)
> +#define USB_STS_ENDIAN2(p) ((p) & USB_STS_ENDIAN2_MASK)
> +
> +/* USB_CMD - bitmasks */
> +/* Set Function Address */
> +#define USB_CMD_SET_ADDR BIT(0)
> +/*
> + * Function Address This field is saved to the device only when the field
> + * SET_ADDR is set '1 ' during write to USB_CMD register.
> + * Software is responsible for entering the address of the device during
> + * SET_ADDRESS request service. This field should be set immediately after
> + * the SETUP packet is decoded, and prior to confirmation of the status phase
> + */
> +#define USB_CMD_FADDR_MASK GENMASK(7, 1)
> +#define USB_CMD_FADDR(p) (((p) << 1) & USB_CMD_FADDR_MASK)
> +/* Send Function Wake Device Notification TP (used only in SS mode). */
> +#define USB_CMD_SDNFW BIT(8)
> +/* Set Test Mode (used only in HS/FS mode). */
> +#define USB_CMD_STMODE BIT(9)
> +/* Test mode selector (used only in HS/FS mode) */
> +#define USB_STS_TMODE_SEL_MASK GENMASK(11, 10)
> +#define USB_STS_TMODE_SEL(p) (((p) << 10) & USB_STS_TMODE_SEL_MASK)
> +/*
> + * Send Latency Tolerance Message Device Notification TP (used only
> + * in SS mode).
> + */
> +#define USB_CMD_SDNLTM BIT(12)
> +/* Send Custom Transaction Packet (used only in SS mode) */
> +#define USB_CMD_SPKT BIT(13)
> +/*Device Notification 'Function Wake' - Interface value (only in SS mode. */
> +#define USB_CMD_DNFW_INT_MASK GENMASK(23, 16)
> +#define USB_STS_DNFW_INT(p) (((p) << 16) & USB_CMD_DNFW_INT_MASK)
> +/*
> + * Device Notification 'Latency Tolerance Message' -373 BELT value [7:0]
> + * (used only in SS mode).
> + */
> +#define USB_CMD_DNLTM_BELT_MASK GENMASK(27, 16)
> +#define USB_STS_DNLTM_BELT(p) (((p) << 16) & USB_CMD_DNLTM_BELT_MASK)
> +
> +/* USB_ITPN - bitmasks */
> +/*
> + * ITP(SS) / SOF (HS/FS) number
> + * In SS mode this field represent number of last ITP received from host.
> + * In HS/FS mode this field represent number of last SOF received from host.
> + */
> +#define USB_ITPN_MASK GENMASK(13, 0)
> +#define USB_ITPN(p) ((p) & USB_ITPN_MASK)
> +
> +/* USB_LPM - bitmasks */
> +/* Host Initiated Resume Duration. */
> +#define USB_LPM_HIRD_MASK GENMASK(3, 0)
> +#define USB_LPM_HIRD(p) ((p) & USB_LPM_HIRD_MASK)
> +/* Remote Wakeup Enable (bRemoteWake). */
> +#define USB_LPM_BRW BIT(4)
> +
> +/* USB_IEN - bitmasks */
> +/* SS connection interrupt enable */
> +#define USB_IEN_CONIEN BIT(0)
> +/* SS disconnection interrupt enable. */
> +#define USB_IEN_DISIEN BIT(1)
> +/* USB SS warm reset interrupt enable. */
> +#define USB_IEN_UWRESIEN BIT(2)
> +/* USB SS hot reset interrupt enable */
> +#define USB_IEN_UHRESIEN BIT(3)
> +/* SS link U3 state enter interrupt enable (suspend).*/
> +#define USB_IEN_U3ENTIEN BIT(4)
> +/* SS link U3 state exit interrupt enable (wakeup). */
> +#define USB_IEN_U3EXTIEN BIT(5)
> +/* SS link U2 state enter interrupt enable.*/
> +#define USB_IEN_U2ENTIEN BIT(6)
> +/* SS link U2 state exit interrupt enable.*/
> +#define USB_IEN_U2EXTIEN BIT(7)
> +/* SS link U1 state enter interrupt enable.*/
> +#define USB_IEN_U1ENTIEN BIT(8)
> +/* SS link U1 state exit interrupt enable.*/
> +#define USB_IEN_U1EXTIEN BIT(9)
> +/* ITP/SOF packet detected interrupt enable.*/
> +#define USB_IEN_ITPIEN BIT(10)
> +/* Wakeup interrupt enable.*/
> +#define USB_IEN_WAKEIEN BIT(11)
> +/* Send Custom Packet interrupt enable.*/
> +#define USB_IEN_SPKTIEN BIT(12)
> +/* HS/FS mode connection interrupt enable.*/
> +#define USB_IEN_CON2IEN BIT(16)
> +/* HS/FS mode disconnection interrupt enable.*/
> +#define USB_IEN_DIS2IEN BIT(17)
> +/* USB reset (HS/FS mode) interrupt enable.*/
> +#define USB_IEN_U2RESIEN BIT(18)
> +/* LPM L2 state enter interrupt enable.*/
> +#define USB_IEN_L2ENTIEN BIT(20)
> +/* LPM L2 state exit interrupt enable.*/
> +#define USB_IEN_L2EXTIEN BIT(21)
> +/* LPM L1 state enter interrupt enable.*/
> +#define USB_IEN_L1ENTIEN BIT(24)
> +/* LPM L1 state exit interrupt enable.*/
> +#define USB_IEN_L1EXTIEN BIT(25)
> +/* Configuration reset interrupt enable.*/
> +#define USB_IEN_CFGRESIEN BIT(26)
> +/* Start of the USB SS warm reset interrupt enable.*/
> +#define USB_IEN_UWRESSIEN BIT(28)
> +/* End of the USB SS warm reset interrupt enable.*/
> +#define USB_IEN_UWRESEIEN BIT(29)
> +
> +#define USB_IEN_INIT (USB_IEN_U2RESIEN | USB_ISTS_DIS2I | USB_IEN_CON2IEN \
> + | USB_IEN_UHRESIEN | USB_IEN_UWRESIEN | USB_IEN_DISIEN \
> + | USB_IEN_CONIEN | USB_IEN_U3EXTIEN | USB_IEN_L2ENTIEN \
> + | USB_IEN_L2EXTIEN)
> +
> +/* USB_ISTS - bitmasks */
> +/* SS Connection detected. */
> +#define USB_ISTS_CONI BIT(0)
> +/* SS Disconnection detected. */
> +#define USB_ISTS_DISI BIT(1)
> +/* UUSB warm reset detectede. */
> +#define USB_ISTS_UWRESI BIT(2)
> +/* USB hot reset detected. */
> +#define USB_ISTS_UHRESI BIT(3)
> +/* U3 link state enter detected (suspend).*/
> +#define USB_ISTS_U3ENTI BIT(4)
> +/* U3 link state exit detected (wakeup). */
> +#define USB_ISTS_U3EXTI BIT(5)
> +/* U2 link state enter detected.*/
> +#define USB_ISTS_U2ENTI BIT(6)
> +/* U2 link state exit detected.*/
> +#define USB_ISTS_U2EXTI BIT(7)
> +/* U1 link state enter detected.*/
> +#define USB_ISTS_U1ENTI BIT(8)
> +/* U1 link state exit detected.*/
> +#define USB_ISTS_U1EXTI BIT(9)
> +/* ITP/SOF packet detected.*/
> +#define USB_ISTS_ITPI BIT(10)
> +/* Wakeup detected.*/
> +#define USB_ISTS_WAKEI BIT(11)
> +/* Send Custom Packet detected.*/
> +#define USB_ISTS_SPKTI BIT(12)
> +/* HS/FS mode connection detected.*/
> +#define USB_ISTS_CON2I BIT(16)
> +/* HS/FS mode disconnection detected.*/
> +#define USB_ISTS_DIS2I BIT(17)
> +/* USB reset (HS/FS mode) detected.*/
> +#define USB_ISTS_U2RESI BIT(18)
> +/* LPM L2 state enter detected.*/
> +#define USB_ISTS_L2ENTI BIT(20)
> +/* LPM L2 state exit detected.*/
> +#define USB_ISTS_L2EXTI BIT(21)
> +/* LPM L1 state enter detected.*/
> +#define USB_ISTS_L1ENTI BIT(24)
> +/* LPM L1 state exit detected.*/
> +#define USB_ISTS_L1EXTI BIT(25)
> +/* USB configuration reset detected.*/
> +#define USB_ISTS_CFGRESI BIT(26)
> +/* Start of the USB warm reset detected.*/
> +#define USB_ISTS_UWRESSI BIT(28)
> +/* End of the USB warm reset detected.*/
> +#define USB_ISTS_UWRESEI BIT(29)
> +
> +/* USB_SEL - bitmasks */
> +#define EP_SEL_EPNO_MASK GENMASK(3, 0)
> +/* Endpoint number. */
> +#define EP_SEL_EPNO(p) ((p) & EP_SEL_EPNO_MASK)
> +/* Endpoint direction bit - 0 - OUT, 1 - IN. */
> +#define EP_SEL_DIR BIT(7)
> +
> +#define select_ep_in(nr) (EP_SEL_EPNO(p) | EP_SEL_DIR)
> +#define select_ep_out (EP_SEL_EPNO(p))
> +
> +/* EP_TRADDR - bitmasks */
> +/* Transfer Ring address. */
> +#define EP_TRADDR_TRADDR(p) ((p))
> +
> +/* EP_CFG - bitmasks */
> +/* Endpoint enable */
> +#define EP_CFG_ENABLE BIT(0)
> +/*
> + * Endpoint type.
> + * 1 - isochronous
> + * 2 - bulk
> + * 3 - interrupt
> + */
> +#define EP_CFG_EPTYPE_MASK GENMASK(2, 1)
> +#define EP_CFG_EPTYPE(p) (((p) << 1) & EP_CFG_EPTYPE_MASK)
> +/* Stream support enable (only in SS mode). */
> +#define EP_CFG_STREAM_EN BIT(3)
> +/* TDL check (only in SS mode for BULK EP). */
> +#define EP_CFG_TDL_CHK BIT(4)
> +/* SID check (only in SS mode for BULK OUT EP). */
> +#define EP_CFG_SID_CHK BIT(5)
> +/* DMA transfer endianness. */
> +#define EP_CFG_EPENDIAN BIT(7)
> +/* Max burst size (used only in SS mode). */
> +#define EP_CFG_MAXBURST_MASK GENMASK(11, 8)
> +#define EP_CFG_MAXBURST(p) (((p) << 8) & EP_CFG_MAXBURST_MASK)
> +/* ISO max burst. */
> +#define EP_CFG_MULT_MASK GENMASK(15, 14)
> +#define EP_CFG_MULT(p) (((p) << 14) & EP_CFG_MULT)
> +/* ISO max burst. */
> +#define EP_CFG_MAXPKTSIZE_MASK GENMASK(26, 16)
> +#define EP_CFG_MAXPKTSIZE(p) (((p) << 16) & EP_CFG_MAXPKTSIZE_MASK)
> +/* Max number of buffered packets. */
> +#define EP_CFG_BUFFERING_MASK GENMASK(31, 27)
> +#define EP_CFG_BUFFERING(p) (((p) << 27) & EP_CFG_BUFFERING_MASK)
> +
> +/* EP_CMD - bitmasks */
> +/* Endpoint reset. */
> +#define EP_CMD_EPRST BIT(0)
> +/* Endpoint STALL set. */
> +#define EP_CMD_SSTALL BIT(1)
> +/* Endpoint STALL clear. */
> +#define EP_CMD_CSTALL BIT(2)
> +/* Send ERDY TP. */
> +#define EP_CMD_ERDY BIT(3)
> +/* Request complete. */
> +#define EP_CMD_REQ_CMPL BIT(5)
> +/* Transfer descriptor ready. */
> +#define EP_CMD_DRDY BIT(6)
> +/* Data flush. */
> +#define EP_CMD_DFLUSH BIT(7)
> +/*
> + * Transfer Descriptor Length write (used only for Bulk Stream capable
> + * endpoints in SS mode).
> + */
> +#define EP_CMD_STDL BIT(8)
> +/* Transfer Descriptor Length (used only in SS mode for bulk endpoints). */
> +#define EP_CMD_TDL_MASK GENMASK(15, 9)
> +#define EP_CMD_TDL(p) (((p) << 9) & EP_CMD_TDL_MASK)
> +/* ERDY Stream ID value (used in SS mode). */
> +#define EP_CMD_ERDY_SID_MASK GENMASK(31, 16)
> +#define EP_CMD_ERDY_SID(p) (((p) << 16) & EP_CMD_SID_MASK)
> +
> +/* EP_STS - bitmasks */
> +/* Setup transfer complete. */
> +#define EP_STS_SETUP BIT(0)
> +/* Endpoint STALL status. */
> +#define EP_STS_STALL(p) ((p) & BIT(1))
> +/* Interrupt On Complete. */
> +#define EP_STS_IOC BIT(2)
> +/* Interrupt on Short Packet. */
> +#define EP_STS_ISP BIT(3)
> +/* Transfer descriptor missing. */
> +#define EP_STS_DESCMIS BIT(4)
> +/* Stream Rejected (used only in SS mode) */
> +#define EP_STS_STREAMR BIT(5)
> +/* EXIT from MOVE DATA State (used only for stream transfers in SS mode). */
> +#define EP_STS_MD_EXIT BIT(6)
> +/* TRB error. */
> +#define EP_STS_TRBERR BIT(7)
> +/* Not ready (used only in SS mode). */
> +#define EP_STS_NRDY BIT(8)
> +/* DMA busy. */
> +#define EP_STS_DBUSY(p) ((p) & BIT(9))
> +/* Endpoint Buffer Empty */
> +#define EP_STS_BUFFEMPTY(p) ((p) & BIT(10))
> +/* Current Cycle Status */
> +#define EP_STS_CCS(p) ((p) & BIT(11))
> +/* Prime (used only in SS mode. */
> +#define EP_STS_PRIME BIT(12)
> +/* Stream error (used only in SS mode). */
> +#define EP_STS_SIDERR BIT(13)
> +/* OUT size mismatch. */
> +#define EP_STS_OUTSMM BIT(14)
> +/* ISO transmission error. */
> +#define EP_STS_ISOERR BIT(15)
> +/* Host Packet Pending (only for SS mode). */
> +#define EP_STS_HOSTPP(p) ((p) & BIT(16))
> +/* Stream Protocol State Machine State (only for Bulk stream endpoints). */
> +#define EP_STS_SPSMST_MASK GENMASK(18, 17)
> +#define EP_STS_SPSMST_DISABLED(p) (((p) & EP_STS_SPSMST_MASK) >> 17)
> +#define EP_STS_SPSMST_IDLE(p) (((p) & EP_STS_SPSMST_MASK) >> 17)
> +#define EP_STS_SPSMST_START_STREAM(p) (((p) & EP_STS_SPSMST_MASK) >> 17)
> +#define EP_STS_SPSMST_MOVE_DATA(p) (((p) & EP_STS_SPSMST_MASK) >> 17)
> +/* Interrupt On Transfer complete. */
> +#define EP_STS_IOT BIT(19)
> +/* OUT queue endpoint number. */
> +#define EP_STS_OUTQ_NO_MASK GENMASK(27, 24)
> +#define EP_STS_OUTQ_NO(p) (((p) & EP_STS_OUTQ_NO_MASK) >> 24)
> +/* OUT queue valid flag. */
> +#define EP_STS_OUTQ_VAL_MASK BIT(28)
> +#define EP_STS_OUTQ_VAL(p) ((p) & EP_STS_OUTQ_VAL_MASK)
> +/* SETUP WAIT. */
> +#define EP_STS_STPWAIT BIT(31)
> +
> +/* EP_STS_SID - bitmasks */
> +/* Stream ID (used only in SS mode). */
> +#define EP_STS_SID_MASK GENMASK(15, 0)
> +#define EP_STS_SID(p) ((p) & EP_STS_SID_MASK)
> +
> +/* EP_STS_EN - bitmasks */
> +/* SETUP interrupt enable. */
> +#define EP_STS_EN_SETUPEN BIT(0)
> +/* OUT transfer missing descriptor enable. */
> +#define EP_STS_EN_DESCMISEN BIT(4)
> +/* Stream Rejected enable. */
> +#define EP_STS_EN_STREAMREN BIT(5)
> +/* Move Data Exit enable.*/
> +#define EP_STS_EN_MD_EXITEN BIT(6)
> +/* TRB enable. */
> +#define EP_STS_EN_TRBERREN BIT(7)
> +/* NRDY enable. */
> +#define EP_STS_EN_NRDYEN BIT(8)
> +/* Prime enable. */
> +#define EP_STS_EN_PRIMEEEN BIT(12)
> +/* Stream error enable. */
> +#define EP_STS_EN_SIDERREN BIT(13)
> +/* OUT size mismatch enable. */
> +#define EP_STS_EN_OUTSMMEN BIT(14)
> +/* ISO transmission error enable. */
> +#define EP_STS_EN_ISOERREN BIT(15)
> +/* Interrupt on Transmission complete enable. */
> +#define EP_STS_EN_IOTEN BIT(19)
> +/* Setup Wait interrupt enable. */
> +#define EP_STS_EN_STPWAITEN BIT(31)
> +
> +/* DRBL- bitmasks */
> +#define DB_VALUE_BY_INDEX(index) (1 << (index))
> +#define DB_VALUE_EP0_OUT BIT(0)
> +#define DB_VALUE_EP0_IN BIT(16)
> +
> +/* EP_IEN - bitmasks */
> +#define EP_IEN(index) (1 << (index))
> +#define EP_IEN_EP_OUT0 BIT(0)
> +#define EP_IEN_EP_IN0 BIT(16)
> +
> +/* EP_ISTS - bitmasks */
> +#define EP_ISTS(index) (1 << (index))
> +#define EP_ISTS_EP_OUT0 BIT(0)
> +#define EP_ISTS_EP_IN0 BIT(16)
> +
> +/* EP_PWR- bitmasks */
> +/*Power Shut Off capability enable*/
> +#define PUSB_PWR_PSO_EN BIT(0)
> +/*Power Shut Off capability disable*/
> +#define PUSB_PWR_PSO_DS BIT(1)
> +/*
> + * Enables turning-off Reference Clock.
> + * This bit is optional and implemented only when support for OTG is
> + * implemented (indicated by OTG_READY bit set to '1').
> + */
> +#define PUSB_PWR_STB_CLK_SWITCH_EN BIT(8)
> +/*
> + * Status bit indicating that operation required by STB_CLK_SWITCH_EN write
> + * is completed
> + */
> +#define PUSB_PWR_STB_CLK_SWITCH_DONE BIT(9)
> +/* This bit informs if Fast Registers Access is enabled. */
> +#define PUSB_PWR_FST_REG_ACCESS_STAT BIT(30)
> +/* Fast Registers Access Enable. */
> +#define PUSB_PWR_FST_REG_ACCESS BIT(31)
> +
> +/* USB_CAP1- bitmasks */
> +/*
> + * SFR Interface type
> + * These field reflects type of SFR interface implemented:
> + * 0x0 - OCP
> + * 0x1 - AHB,
> + * 0x2 - PLB
> + * 0x3 - AXI
> + * 0x4-0xF - reserved
> + */
> +#define USB_CAP1_SFR_TYPE_MASK GENMASK(3, 0)
> +#define DEV_SFR_TYPE_OCP(p) (((p) & USB_CAP1_SFR_TYPE_MASK) == 0x0)
> +#define DEV_SFR_TYPE_AHB(p) (((p) & USB_CAP1_SFR_TYPE_MASK) == 0x1)
> +#define DEV_SFR_TYPE_PLB(p) (((p) & USB_CAP1_SFR_TYPE_MASK) == 0x2)
> +#define DEV_SFR_TYPE_AXI(p) (((p) & USB_CAP1_SFR_TYPE_MASK) == 0x3)
> +/*
> + * SFR Interface width
> + * These field reflects width of SFR interface implemented:
> + * 0x0 - 8 bit interface,
> + * 0x1 - 16 bit interface,
> + * 0x2 - 32 bit interface
> + * 0x3 - 64 bit interface
> + * 0x4-0xF - reserved
> + */
> +#define USB_CAP1_SFR_WIDTH_MASK GENMASK(7, 4)
> +#define DEV_SFR_WIDTH_8(p) (((p) & USB_CAP1_SFR_WIDTH_MASK) == (0x0 << 4))
> +#define DEV_SFR_WIDTH_16(p) (((p) & USB_CAP1_SFR_WIDTH_MASK) == (0x1 << 4))
> +#define DEV_SFR_WIDTH_32(p) (((p) & USB_CAP1_SFR_WIDTH_MASK) == (0x2 << 4))
> +#define DEV_SFR_WIDTH_64(p) (((p) & USB_CAP1_SFR_WIDTH_MASK) == (0x3 << 4))
> +/*
> + * DMA Interface type
> + * These field reflects type of DMA interface implemented:
> + * 0x0 - OCP
> + * 0x1 - AHB,
> + * 0x2 - PLB
> + * 0x3 - AXI
> + * 0x4-0xF - reserved
> + */
> +#define USB_CAP1_DMA_TYPE_MASK GENMASK(11, 8)
> +#define DEV_DMA_TYPE_OCP(p) (((p) & USB_CAP1_DMA_TYPE_MASK) == (0x0 << 8))
> +#define DEV_DMA_TYPE_AHB(p) (((p) & USB_CAP1_DMA_TYPE_MASK) == (0x1 << 8))
> +#define DEV_DMA_TYPE_PLB(p) (((p) & USB_CAP1_DMA_TYPE_MASK) == (0x2 << 8))
> +#define DEV_DMA_TYPE_AXI(p) (((p) & USB_CAP1_DMA_TYPE_MASK) == (0x3 << 8))
> +/*
> + * DMA Interface width
> + * These field reflects width of DMA interface implemented:
> + * 0x0 - reserved,
> + * 0x1 - reserved,
> + * 0x2 - 32 bit interface
> + * 0x3 - 64 bit interface
> + * 0x4-0xF - reserved
> + */
> +#define USB_CAP1_DMA_WIDTH_MASK GENMASK(15, 12)
> +#define DEV_DMA_WIDTH_32(p) (((p) & USB_CAP1_DMA_WIDTH_MASK) == (0x2 << 12))
> +#define DEV_DMA_WIDTH_64(p) (((p) & USB_CAP1_DMA_WIDTH_MASK) == (0x3 << 12))
> +/*
> + * USB3 PHY Interface type
> + * These field reflects type of USB3 PHY interface implemented:
> + * 0x0 - USB PIPE,
> + * 0x1 - RMMI,
> + * 0x2-0xF - reserved
> + */
> +#define USB_CAP1_U3PHY_TYPE_MASK GENMASK(19, 16)
> +#define DEV_U3PHY_PIPE(p) (((p) & USB_CAP1_U3PHY_TYPE_MASK) == (0x0 << 16))
> +#define DEV_U3PHY_RMMI(p) (((p) & USB_CAP1_U3PHY_TYPE_MASK) == (0x1 << 16))
> +/*
> + * USB3 PHY Interface width
> + * These field reflects width of USB3 PHY interface implemented:
> + * 0x0 - 8 bit PIPE interface,
> + * 0x1 - 16 bit PIPE interface,
> + * 0x2 - 32 bit PIPE interface,
> + * 0x3 - 64 bit PIPE interface
> + * 0x4-0xF - reserved
> + * Note: When SSIC interface is implemented this field shows the width of
> + * internal PIPE interface. The RMMI interface is always 20bit wide.
> + */
> +#define USB_CAP1_U3PHY_WIDTH_MASK GENMASK(23, 20)
> +#define DEV_U3PHY_WIDTH_8(p) \
> + (((p) & USB_CAP1_U3PHY_WIDTH_MASK) == (0x0 << 20))
> +#define DEV_U3PHY_WIDTH_16(p) \
> + (((p) & USB_CAP1_U3PHY_WIDTH_MASK) == (0x1 << 16))
> +#define DEV_U3PHY_WIDTH_32(p) \
> + (((p) & USB_CAP1_U3PHY_WIDTH_MASK) == (0x2 << 20))
> +#define DEV_U3PHY_WIDTH_64(p) \
> + (((p) & USB_CAP1_U3PHY_WIDTH_MASK) == (0x3 << 16))
> +
> +/*
> + * USB2 PHY Interface enable
> + * These field informs if USB2 PHY interface is implemented:
> + * 0x0 - interface NOT implemented,
> + * 0x1 - interface implemented
> + */
> +#define USB_CAP1_U2PHY_EN(p) ((p) & BIT(24))
> +/*
> + * USB2 PHY Interface type
> + * These field reflects type of USB2 PHY interface implemented:
> + * 0x0 - UTMI,
> + * 0x1 - ULPI
> + */
> +#define DEV_U2PHY_ULPI(p) ((p) & BIT(25))
> +/*
> + * USB2 PHY Interface width
> + * These field reflects width of USB2 PHY interface implemented:
> + * 0x0 - 8 bit interface,
> + * 0x1 - 16 bit interface,
> + * Note: The ULPI interface is always 8bit wide.
> + */
> +#define DEV_U2PHY_WIDTH_16(p) ((p) & BIT(26))
> +/*
> + * OTG Ready
> + * 0x0 - pure device mode
> + * 0x1 - some features and ports for CDNS USB OTG controller are implemented.
> + */
> +#define USB_CAP1_OTG_READY(p) ((p) & BIT(27))
> +
> +/* USB_CAP2- bitmasks */
> +/*
> + * The actual size of the connected On-chip RAM memory in kB:
> + * - 0 means 256 kB (max supported mem size)
> + * - value other than 0 reflects the mem size in kB
> + */
> +#define USB_CAP2_ACTUAL_MEM_SIZE(p) ((p) & GENMASK(7, 0))
> +/*
> + * Max supported mem size
> + * These field reflects width of on-chip RAM address bus width,
> + * which determines max supported mem size:
> + * 0x0-0x7 - reserved,
> + * 0x8 - support for 4kB mem,
> + * 0x9 - support for 8kB mem,
> + * 0xA - support for 16kB mem,
> + * 0xB - support for 32kB mem,
> + * 0xC - support for 64kB mem,
> + * 0xD - support for 128kB mem,
> + * 0xE - support for 256kB mem,
> + * 0xF - reserved
> + */
> +#define USB_CAP2_MAX_MEM_SIZE(p) ((p) & GENMASK(11, 8))
> +
> +/* USB_CAP3- bitmasks */
> +#define EP_IS_IMPLEMENTED(reg, index) ((reg) & (1 << (index)))
> +
> +/* USB_CAP4- bitmasks */
> +#define EP_SUPPORT_ISO(reg, index) ((reg) & (1 << (index)))
> +
> +/* USB_CAP5- bitmasks */
> +#define EP_SUPPORT_STREAM(reg, index) ((reg) & (1 << (index)))
> +
> +/* USB_CAP6- bitmasks */
> +/* The USBSS-DEV Controller Internal build number. */
> +#define GET_DEV_VERSION__INTERNAL_NUMBER(p) ((p) & GENMASK(7, 0))
> +/* The USBSS-DEV Controller version number. */
> +#define GET_DEV_VERSION(p) ((p) & GENMASK(31, 8))
> +
> +/* DBG_LINK1- bitmasks */
> +/*
> + * LFPS_MIN_DET_U1_EXIT value This parameter configures the minimum
> + * time required for decoding the received LFPS as an LFPS.U1_Exit.
> + */
> +#define DBG_LINK1_LFPS_MIN_DET_U1_EXIT(p) ((p) & GENMASK(7, 0))
> +/*
> + * LFPS_MIN_GEN_U1_EXIT value This parameter configures the minimum time for
> + * phytxelecidle deassertion when LFPS.U1_Exit
> + */
> +#define DBG_LINK1_LFPS_MIN_GEN_U1_EXIT(p) (((p) << 8) & GENMASK(15, 8))
> +/*
> + * RXDET_BREAK_DIS value This parameter configures terminating the Far-end
> + * Receiver termination detection sequence:
> + * 0: it is possible that USBSS_DEV will terminate Farend receiver
> + * termination detection sequence
> + * 1: USBSS_DEV will not terminate Far-end receiver termination
> + * detection sequence
> + */
> +#define DBG_LINK1_RXDET_BREAK_DIS BIT(16)
> +/* LFPS_GEN_PING value This parameter configures the LFPS.Ping generation */
> +#define DBG_LINK1_LFPS_GEN_PING(p) (((p) << 17) & GENMASK(21, 17))
> +/*
> + * Set the LFPS_MIN_DET_U1_EXIT value Writing '1' to this bit writes the
> + * LFPS_MIN_DET_U1_EXIT field value to the device. This bit is automatically
> + * cleared. Writing '0' has no effect
> + */
> +#define DBG_LINK1_LFPS_MIN_DET_U1_EXIT_SET BIT(24)
> +/*
> + * Set the LFPS_MIN_GEN_U1_EXIT value. Writing '1' to this bit writes the
> + * LFPS_MIN_GEN_U1_EXIT field value to the device. This bit is automatically
> + * cleared. Writing '0' has no effect
> + */
> +#define DBG_LINK1_LFPS_MIN_GEN_U1_EXIT_SET BIT(25)
> +/*
> + * Set the RXDET_BREAK_DIS value Writing '1' to this bit writes
> + * the RXDET_BREAK_DIS field value to the device. This bit is automatically
> + * cleared. Writing '0' has no effect
> + */
> +#define DBG_LINK1_RXDET_BREAK_DIS_SET BIT(26)
> +/*
> + * Set the LFPS_GEN_PING_SET value Writing '1' to this bit writes
> + * the LFPS_GEN_PING field value to the device. This bit is automatically
> + * cleared. Writing '0' has no effect."
> + */
> +#define DBG_LINK1_LFPS_GEN_PING_SET BIT(27)
> +
> +#define gadget_to_cdns3_device(g) (container_of(g, struct cdns3_device, gadget))
> +
> +#define ep_to_cdns3_ep(ep) (container_of(ep, struct cdns3_endpoint, endpoint))
> +
> +/*-------------------------------------------------------------------------*/
> +/*
> + * USBSS-DEV DMA interface .
> + */
> +#define TRBS_PER_SEGMENT 16
> +
> +/**
> + * struct cdns3_trb - represent Transfer Descriptor block.
> + * @buffer: pointer to buffer data
> + * @length: length of data
> + * @control: control flags.
> + *
> + * This structure describes transfer block serviced by DMA module.
> + */
> +struct cdns3_trb {
> + __le32 buffer;
> + __le32 length;
> + __le32 control;
> +};
> +
> +#define TRB_SIZE (sizeof(struct cdns3_trb))
> +#define TRB_RING_SIZE (TRB_SIZE * TRBS_PER_SEGMENT)
> +
> +/* TRB bit mask */
> +#define TRB_TYPE_BITMASK GENMASK(15, 10)
> +#define TRB_TYPE(p) ((p) << 10)
> +#define TRB_FIELD_TO_TYPE(p) (((p) & TRB_TYPE_BITMASK) >> 10)
> +
> +/* TRB type IDs */
> +/* bulk, interrupt, isoc , and control data stage */
> +#define TRB_NORMAL 1
> +/* TRB for linking ring segments */
> +#define TRB_LINK 6
> +
> +/* Cycle bit - indicates TRB ownership by driver or hw*/
> +#define TRB_CYCLE BIT(0)
> +/*
> + * When set to '1', the device will toggle its interpretation of the Cycle bit
> + */
> +#define TRB_TOGGLE BIT(1)
> +
> +/* Interrupt on short packet*/
> +#define TRB_ISP BIT(2)
> +/*Setting this bit enables FIFO DMA operation mode*/
> +#define TRB_FIFO_MODE BIT(3)
> +/* Set PCIe no snoop attribute */
> +#define TRB_CHAIN BIT(4)
> +/* Interrupt on completion */
> +#define TRB_IOC BIT(5)
> +
> +/* stream ID bitmasks. */
> +#define TRB_STREAM_ID(p) ((p) & GENMASK(31, 16))
> +
> +/* transfer_len bitmasks. */
> +#define TRB_LEN(p) ((p) & GENMASK(16, 0))
> +
> +/* transfer_len bitmasks - bits 31:24 */
> +#define TRB_BURST_LEN(p) ((p) & GENMASK(31, 24))
> +
> +/* Data buffer pointer bitmasks*/
> +#define TRB_BUFFER(p) ((p) & GENMASK(31, 0))
> +
> +/*-------------------------------------------------------------------------*/
> +/* Driver numeric constants */
> +
> +/* Such declaration should be added to ch9.h */
> +#define USB_DEVICE_MAX_ADDRESS 127
> +
> +/* Endpoint init values */
> +#define CDNS3_EP_MAX_PACKET_LIMIT 1024
> +#define CDNS3_EP_MAX_STREAMS 15
> +
> +#define CDNS3_EP0_MAX_PACKET_LIMIT 512
> +
> +/* All endpoints except EP0 */
> +#define CDNS3_ENDPOINTS_MAX_COUNT 30
> +
> +#define CDNS3_EP_ZLP_BUF_SIZE 1024
> +
> +/*-------------------------------------------------------------------------*/
> +#define CDNS3_EP_BUF_SIZE 2 /* KB */
> +#define CDNS3_ALIGNED_BUF_SIZE 16384 /* Bytes */
> +#define CDNS3_DESCMIS_BUF_SIZE 65536 /* Bytes */
> +/*-------------------------------------------------------------------------*/
> +/* Used structs */
> +
> +struct cdns3_device;
> +
> +/**
> + * struct cdns3_endpoint - extended device side representation of USB endpoint.
> + * @endpoint: usb endpoint
> + * @request_list: list of request for this endpoint
> + * @trb_pool: transfer ring - array of transaction buffers
> + * @trb_pool_dma: dma address of transfer ring
> + * @cdns3_dev: device associated with this endpoint
> + * @name: a human readable name e.g. ep1out
> + * @flags: specify the current state of endpoint
> + * @descmis_req: internal transfer object used for getting data from on-chip
> + * buffer. It can happen only if function driver doesn't send usb_request
> + * object on time.
> + * @descmis_pending: flag specify that internal buffer was used for DMA to
> + * take data from shared on-chip buffers to avoid blocking transfer to other
> + * endpoints. It indicate that is still in progress.
> + * @descmis_finished: flag specify that transfer has armed on descriptor
> + * missing event has been completed. If function driver requests
> + * the transfer then controller driver can just return this data.
> + * @aligned_buff: aligned to 8 bytes data buffer. Buffer address used in
> + * TRB shall be aligned to 8.
> + * @aligned_dma_addr: dma address of aligned_buff
> + * @dir: endpoint direction
> + * @num: endpoint number (1 - 15)
> + * @type: set to bmAttributes & USB_ENDPOINT_XFERTYPE_MASK
> + * @free_trbs: number of free TRBs in transfer ring
> + * @pcs: producer cycle state
> + * @ccs: consumer cycle state
> + * @enqueue: enqueue index in transfer ring
> + * @dequeue: dequeue index in transfer ring
> + */
> +struct cdns3_endpoint {
> + struct usb_ep endpoint;
> + struct list_head request_list;
> +
> + struct cdns3_trb *trb_pool;
> + dma_addr_t trb_pool_dma;
> +
> + struct cdns3_device *cdns3_dev;
> + char name[20];
> +
> +#define EP_ENABLED BIT(0)
> +#define EP_STALL BIT(1)
> +#define EP_WEDGE BIT(2)
> +#define EP_TRANSFER_STARTED BIT(3)
> +#define EP_UPDATE_EP_TRBADDR BIT(4)
> +#define EP_PENDING_REQUEST BIT(5)
> +#define EP_RING_FULL BIT(6)
> +#define EP_CLAIMED BIT(5)
> + u32 flags;
> +
> + struct cdns3_request *descmis_req;
> + u32 descmis_pending:1;
> + u32 descmis_finished:1;
> +
> + void *aligned_buff;
> + dma_addr_t aligned_dma_addr;
> + u8 dir;
> + u8 num;
> + u8 type;
> +
> + int free_trbs;
> + u8 pcs;
> + u8 ccs;
> + int enqueue;
> + int dequeue;
> +};
> +
> +/**
> + * struct cdns3_request - extended device side representation of usb_request
> + * object .
> + * @request: generic usb_request object describing single I/O request.
> + * @priv_ep: extended representation of usb_ep object
> + * @trb: the first TRB association with this request
> + * @start_trb: number of the first TRB in transfer ring
> + * @end_trb: number of the last TRB in transfer ring
> + * @flags: flag specifying special usage of request
> + */
> +struct cdns3_request {
> + struct usb_request request;
> + struct cdns3_endpoint *priv_ep;
> + struct cdns3_trb *trb;
> + int start_trb;
> + int end_trb;
> +#define REQUEST_PENDING BIT(0)
> +#define REQUEST_INTERNAL BIT(1)
> +#define REQUEST_ZLP BIT(2)
> + u32 flags;
> +};
> +
> +#define to_cdns3_request(r) (container_of(r, struct cdns3_request, request))
> +
> +/**
> + * struct cdns3_device - represent USB device.
> + * @dev: pointer to device structure associated whit this controller
> + * @sysdev: pointer to the DMA capable device
> + * @gadget: device side representation of the peripheral controller
> + * @gadget_driver: pointer to the gadget driver
> + * @lock: for synchronizing
> + * @regs: base address for device side registers
> + * @setup_buf: used while processing usb control requests
> + * @setup_dma: dma address for setup_buf
> + * @ep0_trb: TRB used for control transfer
> + * @ep0_trb_dma: dma address of ep0_trb
> + * @zlp_buf - zlp buffer
> + * @ep0_request: dummy request used while handling USB control request
> + * @ep0_data_dir: direction for control transfer
> + * @eps: array of pointers to all endpoints with exclusion ep0
> + * @ep_nums: number of endpoints in eps
> + * @isoch_delay: value from Set Isoch Delay request. Only valid on SS/SSP.
> + * @u1_allowed: allow device transition to u1 state
> + * @u2_allowed: allow device transition to u2 state
> + * @is_selfpowered: device is self powered
> + * @setup_pending: setup packet is processing by gadget driver
> + * @hw_configured_flag: hardware endpoint configuration was set.
> + * @wake_up_flag: allow device to remote up the host
> + * @status_completion_no_call: indicate that driver is waiting for status s
> + * stage completion. It's used in deferred SET_CONFIGURATION request.
> + * @onchip_mem_allocated_size: actual size of on-chip memory assigned
> + * to endpoints
> + * @pending_status_wq: workqueue handling status stage for deferred requests.
> + * @pending_status_request: request for which status stage was deferred
> + */
> +struct cdns3_device {
> + struct device *dev;
> + struct device *sysdev;
> +
> + struct usb_gadget gadget;
> + struct usb_gadget_driver *gadget_driver;
> +
> + /* generic spin-lock for drivers */
> + spinlock_t lock;
> +
> + struct cdns3_usb_regs __iomem *regs;
> +
> + struct usb_ctrlrequest *setup_buf;
> + dma_addr_t setup_dma;
> + struct cdns3_trb *ep0_trb;
> + dma_addr_t ep0_trb_dma;
> + void *zlp_buf;
> + struct usb_request *ep0_request;
> + int ep0_data_dir;
> +
> + struct cdns3_endpoint *eps[CDNS3_ENDPOINTS_MAX_COUNT];
> + int ep_nums;
> +
> + u32 selected_ep;
> + u16 isoch_delay;
> +
> + unsigned u1_allowed:1;
> + unsigned u2_allowed:1;
> + unsigned is_selfpowered:1;
> + unsigned setup_pending:1;
> + int hw_configured_flag:1;
> + int wake_up_flag:1;
> + unsigned status_completion_no_call:1;
> +
> + struct work_struct pending_status_wq;
> + struct usb_request *pending_status_request;
> +
> + /*in KB */
> + int onchip_mem_allocated_size;
> +};
> +
> +int cdns3_handshake(void __iomem *ptr, u32 mask, u32 done, int usec);
> +void cdns3_set_register_bit(void __iomem *ptr, u32 mask);
> +dma_addr_t cdns3_trb_virt_to_dma(struct cdns3_endpoint *priv_ep,
> + struct cdns3_trb *trb);
> +enum usb_device_speed cdns3_get_speed(struct cdns3_device *priv_dev);
> +void cdns3_pending_setup_status_handler(struct work_struct *work);
> +void cdns3_gadget_unconfig(struct cdns3_device *priv_dev);
> +void cdns3_set_hw_configuration(struct cdns3_device *priv_dev);
> +void cdns3_select_ep(struct cdns3_device *priv_dev, u32 ep);
> +void cdns3_allow_enable_l1(struct cdns3_device *priv_dev, int enable);
> +struct usb_request *cdns3_next_request(struct list_head *list);
> +int cdns3_ep_run_transfer(struct cdns3_endpoint *priv_ep,
> + struct usb_request *request);
> +u8 cdns3_ep_addr_to_index(u8 ep_addr);
> +int cdns3_gadget_ep_set_wedge(struct usb_ep *ep);
> +int cdns3_gadget_ep_set_halt(struct usb_ep *ep, int value);
> +struct usb_request *cdns3_gadget_ep_alloc_request(struct usb_ep *ep,
> + gfp_t gfp_flags);
> +void cdns3_gadget_ep_free_request(struct usb_ep *ep,
> + struct usb_request *request);
> +int cdns3_gadget_ep_dequeue(struct usb_ep *ep, struct usb_request *request);
> +void cdns3_gadget_giveback(struct cdns3_endpoint *priv_ep,
> + struct cdns3_request *priv_req,
> + int status);
> +
> +int cdns3_init_ep0(struct cdns3_device *priv_dev);
> +void cdns3_ep0_config(struct cdns3_device *priv_dev);
> +void cdns3_ep_config(struct cdns3_endpoint *priv_ep);
> +void cdns3_check_ep0_interrupt_proceed(struct cdns3_device *priv_dev, int dir);
> +
> +#endif /* __LINUX_CDNS3_GADGET */
> diff --git a/drivers/usb/cdns3/host-export.h b/drivers/usb/cdns3/host-export.h
> new file mode 100644
> index 000000000000..b498a170b7e8
> --- /dev/null
> +++ b/drivers/usb/cdns3/host-export.h
> @@ -0,0 +1,28 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * Cadence USBSS DRD Driver - Host Export APIs
> + *
> + * Copyright (C) 2017-2018 NXP
> + *
> + * Authors: Peter Chen <[email protected]>
> + */
> +#ifndef __LINUX_CDNS3_HOST_EXPORT
> +#define __LINUX_CDNS3_HOST_EXPORT
> +
> +#ifdef CONFIG_USB_CDNS3_HOST
> +
> +int cdns3_host_init(struct cdns3 *cdns);
> +void cdns3_host_exit(struct cdns3 *cdns);
> +
> +#else
> +
> +static inline int cdns3_host_init(struct cdns3 *cdns)
> +{
> + return -ENXIO;
> +}
> +
> +static inline void cdns3_host_exit(struct cdns3 *cdns) { }
> +
> +#endif /* CONFIG_USB_CDNS3_HOST */
> +
> +#endif /* __LINUX_CDNS3_HOST_EXPORT */
> diff --git a/drivers/usb/cdns3/host.c b/drivers/usb/cdns3/host.c
> new file mode 100644
> index 000000000000..e16175e0328a
> --- /dev/null
> +++ b/drivers/usb/cdns3/host.c
> @@ -0,0 +1,74 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Cadence USBSS DRD Driver - host side
> + *
> + * Copyright (C) 2018 Cadence Design Systems.
> + * Copyright (C) 2017-2018 NXP
> + *
> + * Authors: Peter Chen <[email protected]>
> + * Pawel Laszczak <[email protected]>
> + */
> +
> +#include <linux/platform_device.h>
> +#include "core.h"
> +
> +static int __cdns3_host_init(struct cdns3 *cdns)
> +{
> + struct platform_device *xhci;
> + int ret;
> +
> + xhci = platform_device_alloc("xhci-hcd", PLATFORM_DEVID_AUTO);
> + if (!xhci) {
> + dev_err(cdns->dev, "couldn't allocate xHCI device\n");
> + return -ENOMEM;
> + }
> +
> + xhci->dev.parent = cdns->dev;
> + cdns->host_dev = xhci;
> +
> + ret = platform_device_add_resources(xhci, cdns->xhci_res,
> + CDNS3_XHCI_RESOURCES_NUM);
> + if (ret) {
> + dev_err(cdns->dev, "couldn't add resources to xHCI device\n");
> + goto err1;
> + }
> +
> + ret = platform_device_add(xhci);
> + if (ret) {
> + dev_err(cdns->dev, "failed to register xHCI device\n");
> + goto err1;
> + }
> +
> + return 0;
> +err1:
> + platform_device_put(xhci);
> + return ret;
> +}
> +
> +static void cdns3_host_exit(struct cdns3 *cdns)
> +{
> + platform_device_unregister(cdns->host_dev);
> + cdns->host_dev = NULL;
> +}
> +
> +int cdns3_host_init(struct cdns3 *cdns)
> +{
> + struct cdns3_role_driver *rdrv;
> +
> + rdrv = devm_kzalloc(cdns->dev, sizeof(*rdrv), GFP_KERNEL);
> + if (!rdrv)
> + return -ENOMEM;
> +
> + rdrv->start = __cdns3_host_init;
> + rdrv->stop = cdns3_host_exit;
> + rdrv->state = CDNS3_ROLE_STATE_INACTIVE;
> +#if CONFIG_PM
> + rdrv->suspend = NULL;
> + rdrv->resume = NULL;
> +#endif /* CONFIG_PM */
> + rdrv->name = "host";
> +
> + cdns->roles[CDNS3_ROLE_HOST] = rdrv;
> +
> + return 0;
> +}
> diff --git a/drivers/usb/cdns3/trace.c b/drivers/usb/cdns3/trace.c
> new file mode 100644
> index 000000000000..587ae08e019d
> --- /dev/null
> +++ b/drivers/usb/cdns3/trace.c
> @@ -0,0 +1,11 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * USBSS device controller driver Trace Support
> + *
> + * Copyright (C) 2018 Cadence.
> + *
> + * Author: Pawel Laszczak <[email protected]>
> + */
> +
> +#define CREATE_TRACE_POINTS
> +#include "trace.h"
> diff --git a/drivers/usb/cdns3/trace.h b/drivers/usb/cdns3/trace.h
> new file mode 100644
> index 000000000000..a5c8b2a756b4
> --- /dev/null
> +++ b/drivers/usb/cdns3/trace.h
> @@ -0,0 +1,343 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * USBSS device controller driver.
> + * Trace support header file.
> + *
> + * Copyright (C) 2018 Cadence.
> + *
> + * Author: Pawel Laszczak <[email protected]>
> + */
> +
> +#undef TRACE_SYSTEM
> +#define TRACE_SYSTEM cdns3
> +
> +#if !defined(__LINUX_CDNS3_TRACE) || defined(TRACE_HEADER_MULTI_READ)
> +#define __LINUX_CDNS3_TRACE
> +
> +#include <linux/types.h>
> +#include <linux/tracepoint.h>
> +#include <asm/byteorder.h>
> +#include "core.h"
> +#include "gadget.h"
> +#include "debug.h"
> +
> +#define CDNS3_MSG_MAX 500
> +
> +DECLARE_EVENT_CLASS(cdns3_log_doorbell,
> + TP_PROTO(const char *ep_name),
> + TP_ARGS(ep_name),
> + TP_STRUCT__entry(
> + __field(const char *, ep_name)
> + ),
> + TP_fast_assign(
> + __entry->ep_name = ep_name;
> + ),
> + TP_printk("//Ding Dong %s", __entry->ep_name)
> +);
> +
> +DEFINE_EVENT(cdns3_log_doorbell, cdns3_doorbell_ep0,
> + TP_PROTO(const char *ep_name),
> + TP_ARGS(ep_name)
> +);
> +
> +DEFINE_EVENT(cdns3_log_doorbell, cdns3_doorbell_epx,
> + TP_PROTO(const char *ep_name),
> + TP_ARGS(ep_name)
> +);
> +
> +DECLARE_EVENT_CLASS(cdns3_log_usb_irq,
> + TP_PROTO(struct cdns3_device *priv_dev, u32 usb_ists),
> + TP_ARGS(priv_dev, usb_ists),
> + TP_STRUCT__entry(
> + __field(struct cdns3_device *, priv_dev)
> + __field(u32, usb_ists)
> + ),
> + TP_fast_assign(
> + __entry->priv_dev = priv_dev;
> + __entry->usb_ists = usb_ists;
> + ),
> + TP_printk("%s", cdns3_decode_usb_irq(__entry->priv_dev,
> + __entry->usb_ists))
> +);
> +
> +DEFINE_EVENT(cdns3_log_usb_irq, cdns3_usb_irq,
> + TP_PROTO(struct cdns3_device *priv_dev, u32 usb_ists),
> + TP_ARGS(priv_dev, usb_ists)
> +);
> +
> +DECLARE_EVENT_CLASS(cdns3_log_epx_irq,
> + TP_PROTO(struct cdns3_endpoint *priv_ep),
> + TP_ARGS(priv_ep),
> + TP_STRUCT__entry(
> + __field(struct cdns3_endpoint *, priv_ep)
> + ),
> + TP_fast_assign(
> + __entry->priv_ep = priv_ep;
> + ),
> + TP_printk("%s", cdns3_decode_epx_irq(__entry->priv_ep))
> +);
> +
> +DEFINE_EVENT(cdns3_log_epx_irq, cdns3_epx_irq,
> + TP_PROTO(struct cdns3_endpoint *priv_ep),
> + TP_ARGS(priv_ep)
> +);
> +
> +DECLARE_EVENT_CLASS(cdns3_log_ep0_irq,
> + TP_PROTO(struct cdns3_device *priv_dev),
> + TP_ARGS(priv_dev),
> + TP_STRUCT__entry(
> + __field(struct cdns3_device *, priv_dev)
> + ),
> + TP_fast_assign(
> + __entry->priv_dev = priv_dev;
> + ),
> + TP_printk("%s", cdns3_decode_ep0_irq(__entry->priv_dev))
> +);
> +
> +DEFINE_EVENT(cdns3_log_ep0_irq, cdns3_ep0_irq,
> + TP_PROTO(struct cdns3_device *priv_dev),
> + TP_ARGS(priv_dev)
> +);
> +
> +DECLARE_EVENT_CLASS(cdns3_log_ctrl,
> + TP_PROTO(struct usb_ctrlrequest *ctrl),
> + TP_ARGS(ctrl),
> + TP_STRUCT__entry(
> + __field(u8, bRequestType)
> + __field(u8, bRequest)
> + __field(u16, wValue)
> + __field(u16, wIndex)
> + __field(u16, wLength)
> + __dynamic_array(char, str, CDNS3_MSG_MAX)
> + ),
> + TP_fast_assign(
> + __entry->bRequestType = ctrl->bRequestType;
> + __entry->bRequest = ctrl->bRequest;
> + __entry->wValue = le16_to_cpu(ctrl->wValue);
> + __entry->wIndex = le16_to_cpu(ctrl->wIndex);
> + __entry->wLength = le16_to_cpu(ctrl->wLength);
> + ),
> + TP_printk("%s", cdns3_decode_ctrl(__get_str(str), __entry->bRequestType,
> + __entry->bRequest, __entry->wValue,
> + __entry->wIndex, __entry->wLength)
> + )
> +);
> +
> +DEFINE_EVENT(cdns3_log_ctrl, cdns3_ctrl_req,
> + TP_PROTO(struct usb_ctrlrequest *ctrl),
> + TP_ARGS(ctrl)
> +);
> +
> +DECLARE_EVENT_CLASS(cdns3_log_request,
> + TP_PROTO(struct cdns3_request *req),
> + TP_ARGS(req),
> + TP_STRUCT__entry(
> + __string(name, req->priv_ep->name)
> + __field(struct cdns3_request *, req)
> + __field(unsigned int, actual)
> + __field(unsigned int, length)
> + __field(int, status)
> + __field(int, zero)
> + __field(int, short_not_ok)
> + __field(int, no_interrupt)
> + __field(int, start_trb)
> + __field(int, end_trb)
> + __field(struct cdns3_trb *, start_trb_addr)
> + __field(int, flags)
> + ),
> + TP_fast_assign(
> + __assign_str(name, req->priv_ep->name);
> + __entry->req = req;
> + __entry->actual = req->request.actual;
> + __entry->length = req->request.length;
> + __entry->status = req->request.status;
> + __entry->zero = req->request.zero;
> + __entry->short_not_ok = req->request.short_not_ok;
> + __entry->no_interrupt = req->request.no_interrupt;
> + __entry->start_trb = req->start_trb;
> + __entry->end_trb = req->end_trb;
> + __entry->start_trb_addr = req->trb;
> + __entry->flags = req->flags;
> + ),
> + TP_printk("%s: req: %p, length: %u/%u %s%s%s, status: %d,"
> + " trb: [start:%d, end:%d: virt addr %pa], flags:%x ",
> + __get_str(name), __entry->req, __entry->actual, __entry->length,
> + __entry->zero ? "zero | " : "",
> + __entry->short_not_ok ? "short | " : "",
> + __entry->no_interrupt ? "no int" : "",
> + __entry->status,
> + __entry->start_trb,
> + __entry->end_trb,
> + __entry->start_trb_addr,
> + __entry->flags
> + )
> +);
> +
> +DEFINE_EVENT(cdns3_log_request, cdns3_alloc_request,
> + TP_PROTO(struct cdns3_request *req),
> + TP_ARGS(req)
> +);
> +
> +DEFINE_EVENT(cdns3_log_request, cdns3_free_request,
> + TP_PROTO(struct cdns3_request *req),
> + TP_ARGS(req)
> +);
> +
> +DEFINE_EVENT(cdns3_log_request, cdns3_ep_queue,
> + TP_PROTO(struct cdns3_request *req),
> + TP_ARGS(req)
> +);
> +
> +DEFINE_EVENT(cdns3_log_request, cdns3_ep_dequeue,
> + TP_PROTO(struct cdns3_request *req),
> + TP_ARGS(req)
> +);
> +
> +DEFINE_EVENT(cdns3_log_request, cdns3_gadget_giveback,
> + TP_PROTO(struct cdns3_request *req),
> + TP_ARGS(req)
> +);
> +
> +DECLARE_EVENT_CLASS(cdns3_log_trb,
> + TP_PROTO(struct cdns3_endpoint *priv_ep, struct cdns3_trb *trb),
> + TP_ARGS(priv_ep, trb),
> + TP_STRUCT__entry(
> + __string(name, priv_ep->name)
> + __field(struct cdns3_trb *, trb)
> + __field(u32, buffer)
> + __field(u32, length)
> + __field(u32, control)
> + __field(u32, type)
> + ),
> + TP_fast_assign(
> + __assign_str(name, priv_ep->name);
> + __entry->trb = trb;
> + __entry->buffer = trb->buffer;
> + __entry->length = trb->length;
> + __entry->control = trb->control;
> + __entry->type = usb_endpoint_type(priv_ep->endpoint.desc);
> + ),
> + TP_printk("%s: trb 0x%pa, dma buf: 0x%08x, size: %ld, ctrl: 0x%08x (%s%s%s%s%s%s%s)",
> + __get_str(name), __entry->trb, __entry->buffer,
> + TRB_LEN(__entry->length), __entry->control,
> + __entry->control & TRB_CYCLE ? "C=1, " : "C=0, ",
> + __entry->control & TRB_TOGGLE ? "T=1, " : "T=0, ",
> + __entry->control & TRB_ISP ? "ISP, " : "",
> + __entry->control & TRB_FIFO_MODE ? "FIFO, " : "",
> + __entry->control & TRB_CHAIN ? "CHAIN, " : "",
> + __entry->control & TRB_IOC ? "IOC, " : "",
> + TRB_FIELD_TO_TYPE(__entry->control) == TRB_NORMAL ? "Normal" : "LINK"
> + )
> +);
> +
> +DEFINE_EVENT(cdns3_log_trb, cdns3_prepare_trb,
> + TP_PROTO(struct cdns3_endpoint *priv_ep, struct cdns3_trb *trb),
> + TP_ARGS(priv_ep, trb)
> +);
> +
> +DEFINE_EVENT(cdns3_log_trb, cdns3_complete_trb,
> + TP_PROTO(struct cdns3_endpoint *priv_ep, struct cdns3_trb *trb),
> + TP_ARGS(priv_ep, trb)
> +);
> +
> +DECLARE_EVENT_CLASS(cdns3_log_ring,
> + TP_PROTO(struct cdns3_endpoint *priv_ep),
> + TP_ARGS(priv_ep),
> + TP_STRUCT__entry(
> + __field(struct cdns3_endpoint *, priv_ep)
> + __field(int, free_trbs)
> + __field(u8, pcs)
> + __field(u8, ccs)
> + __field(int, enqueue)
> + __field(int, dequeue)
> + __dynamic_array(u32, ring, TRB_RING_SIZE)
> + __dynamic_array(char, buffer,
> + (TRBS_PER_SEGMENT * 65) + CDNS3_MSG_MAX)
> + ),
> + TP_fast_assign(
> + __entry->priv_ep = priv_ep;
> + __entry->free_trbs = priv_ep->free_trbs;
> + __entry->pcs = priv_ep->pcs;
> + __entry->ccs = priv_ep->ccs;
> + __entry->enqueue = priv_ep->enqueue;
> + __entry->dequeue = priv_ep->dequeue;
> + memcpy(__get_dynamic_array(ring), priv_ep->trb_pool,
> + TRB_RING_SIZE);
> + ),
> +
> + TP_printk("%s",
> + cdns3_dbg_ring(__entry->priv_ep, __entry->free_trbs,
> + __entry->pcs, __entry->ccs,
> + __entry->enqueue, __entry->dequeue,
> + (struct cdns3_trb *)__get_str(ring),
> + __get_str(buffer)))
> +);
> +
> +DEFINE_EVENT(cdns3_log_ring, cdns3_ring,
> + TP_PROTO(struct cdns3_endpoint *priv_ep),
> + TP_ARGS(priv_ep)
> +);
> +
> +DECLARE_EVENT_CLASS(cdns3_log_ep,
> + TP_PROTO(struct cdns3_endpoint *priv_ep),
> + TP_ARGS(priv_ep),
> + TP_STRUCT__entry(
> + __string(name, priv_ep->name)
> + __field(unsigned int, maxpacket)
> + __field(unsigned int, maxpacket_limit)
> + __field(unsigned int, max_streams)
> + __field(unsigned int, maxburst)
> + __field(unsigned int, flags)
> + __field(unsigned int, dir)
> + __field(u8, enqueue)
> + __field(u8, dequeue)
> + ),
> + TP_fast_assign(
> + __assign_str(name, priv_ep->name);
> + __entry->maxpacket = priv_ep->endpoint.maxpacket;
> + __entry->maxpacket_limit = priv_ep->endpoint.maxpacket_limit;
> + __entry->max_streams = priv_ep->endpoint.max_streams;
> + __entry->maxburst = priv_ep->endpoint.maxburst;
> + __entry->flags = priv_ep->flags;
> + __entry->dir = priv_ep->dir;
> + __entry->enqueue = priv_ep->enqueue;
> + __entry->dequeue = priv_ep->dequeue;
> + ),
> + TP_printk("%s: mps: %d/%d. streams: %d, burst: %d, enq idx: %d, "
> + "deq idx: %d, flags %s%s%s%s%s%s%s%s, dir: %s",
> + __get_str(name), __entry->maxpacket,
> + __entry->maxpacket_limit, __entry->max_streams,
> + __entry->maxburst, __entry->enqueue,
> + __entry->dequeue,
> + __entry->flags & EP_ENABLED ? "EN | " : "",
> + __entry->flags & EP_STALL ? "STALL | " : "",
> + __entry->flags & EP_WEDGE ? "WEDGE | " : "",
> + __entry->flags & EP_TRANSFER_STARTED ? "STARTED | " : "",
> + __entry->flags & EP_UPDATE_EP_TRBADDR ? "UPD TRB | " : "",
> + __entry->flags & EP_PENDING_REQUEST ? "REQ PEN | " : "",
> + __entry->flags & EP_RING_FULL ? "RING FULL |" : "",
> + __entry->flags & EP_CLAIMED ? "CLAIMED " : "",
> + __entry->dir ? "IN" : "OUT"
> + )
> +);
> +
> +DEFINE_EVENT(cdns3_log_ep, cdns3_gadget_ep_enable,
> + TP_PROTO(struct cdns3_endpoint *priv_ep),
> + TP_ARGS(priv_ep)
> +);
> +
> +DEFINE_EVENT(cdns3_log_ep, cdns3_gadget_ep_disable,
> + TP_PROTO(struct cdns3_endpoint *priv_ep),
> + TP_ARGS(priv_ep)
> +);
> +#endif /* __LINUX_CDNS3_TRACE */
> +
> +/* this part must be outside header guard */
> +
> +#undef TRACE_INCLUDE_PATH
> +#define TRACE_INCLUDE_PATH .
> +
> +#undef TRACE_INCLUDE_FILE
> +#define TRACE_INCLUDE_FILE trace
> +
> +#include <trace/define_trace.h>
> --
> 2.17.1
>

2018-12-14 03:47:51

by Kishon Vijay Abraham I

[permalink] [raw]

Subject: Re: [PATCH v1 2/2] usb:cdns3 Add Cadence USB3 DRD Driver

On 12/12/18 12:22 PM, Felipe Balbi wrote:
>
> Hi
>
> Pawel Laszczak <[email protected]> writes:
>>>> + cdns->phy = devm_phy_get(dev, "cdns3,usbphy");
>>>> + if (IS_ERR(cdns->phy)) {
>>>> + ret = PTR_ERR(cdns->phy);
>>>> + if (ret == -ENOSYS || ret == -ENODEV) {
>>>
>>> Are you sure you can get ENOSYS here? Have you checked output of
>>> checkpatch --strict?
>>> -:852: WARNING: ENOSYS means 'invalid syscall nr' and nothing else
>>
>> Yes this error code can be returned by related to phy function if
>> CONFIG_GENERIC_PHY is disabled.
>>
>> I have seen this warning in output of checkpatch --strict .
>
> Kishon, seems like you shouldn't be using that error value.

hmm, yeah should change the return value to -ENODEV when GENERIC_PHY is disabled.

Thanks
Kishon
>
> <snip>
>
>>>> + case USB_REQ_SET_ISOCH_DELAY:
>>>> + sprintf(str, "Set Isochronous Delay Delay: %d ns", wValue);
>>>> + break;
>>>> + default:
>>>> + sprintf(str,
>>>> + "SETUP BRT: %02x BR: %02x V: %04x I: %04x L: %04x\n",
>>>> + bRequestType, bRequest,
>>>> + wValue, wIndex, wLength);
>>>> + }
>>>> +
>>>> + return str;
>>>> +}
>>>
>>> All of these are a flat out copy of dwc3's implementation. It's much,
>>> much better to turn dwc3's implementation into a generic, reusable
>>> library function then spinning your own as a duplicated effort.
>> I agree,
>> It would be nice to have a set of decoding function in some generic library. It could be used
>> also by other drivers.
>> Who should do this ?
>
> since you're the first to reuse it, then it should be you :-)
>
>>>> +static int cdns3_req_ep0_set_configuration(struct cdns3_device *priv_dev,
>>>> + struct usb_ctrlrequest *ctrl_req)
>>>> +{
>>>> + enum usb_device_state device_state = priv_dev->gadget.state;
>>>> + struct cdns3_endpoint *priv_ep;
>>>> + u32 config = le16_to_cpu(ctrl_req->wValue);
>>>> + int result = 0;
>>>> + int i;
>>>> +
>>>> + switch (device_state) {
>>>> + case USB_STATE_ADDRESS:
>>>> + /* Configure non-control EPs */
>>>> + for (i = 0; i < CDNS3_ENDPOINTS_MAX_COUNT; i++) {
>>>> + priv_ep = priv_dev->eps[i];
>>>> + if (!priv_ep)
>>>> + continue;
>>>> +
>>>> + if (priv_ep->flags & EP_CLAIMED)
>>>> + cdns3_ep_config(priv_ep);
>>>> + }
>>>> +
>>>> + result = cdns3_ep0_delegate_req(priv_dev, ctrl_req);
>>>> +
>>>> + if (result)
>>>> + return result;
>>>> +
>>>> + if (config) {
>>>> + cdns3_set_hw_configuration(priv_dev);
>>>> + } else {
>>>> + cdns3_gadget_unconfig(priv_dev);
>>>> + usb_gadget_set_state(&priv_dev->gadget,
>>>> + USB_STATE_ADDRESS);
>>>
>>> this is wrong. If address is zero, state should be default, not
>>> addressed. Addressed would be used on the other branch here, when you
>>> have a non-zero address
>>
>> If address is zero then state should be USB_STATE_DEFAULT. Driver
>> enters to this branch only if gadget.state = USB_STATE_ADDRESS
>> (address != 0). This state can be changed in composite.c file after
>> delegating request to gadget driver. Because this state could be
>> changed driver simple restore USB_STATE_ADDRESS if config = 0.
>
> nevermind, I read this as being the handler for Set Address. This is Set
> Config, instead.
>
>>>> + }
>>>> + break;
>>>> + case USB_STATE_CONFIGURED:
>>>
>>> where do you set this state?
>> It's set in set_config in composite.c file.
>
> indeed
>
>>>> + case USB_DEVICE_TEST_MODE:
>>>> + if (state != USB_STATE_CONFIGURED || speed > USB_SPEED_HIGH)
>>>> + return -EINVAL;
>>>> +
>>>> + tmode = le16_to_cpu(ctrl->wIndex);
>>>> +
>>>> + if (!set || (tmode & 0xff) != 0)
>>>> + return -EINVAL;
>>>> +
>>>> + switch (tmode >> 8) {
>>>> + case TEST_J:
>>>> + case TEST_K:
>>>> + case TEST_SE0_NAK:
>>>> + case TEST_PACKET:
>>>> + cdns3_set_register_bit(&priv_dev->regs->usb_cmd,
>>>> + USB_CMD_STMODE |
>>>> + USB_STS_TMODE_SEL(tmode - 1));
>>>
>>> I'm 90% sure this won't work. There's a reason why we only enter the
>>> requested test mode from status stage. How have you tested this?
>>
>> From USB spec:
>> "The transition to test mode must be complete no later than 3 ms after the completion of the status stage of the
>> request."
>
> exactly, _after_ completion of status stage :-)
>
>> But I don't remember any issues with this test on other ours
>> drivers. Maybe status stage is armed in this case by controller. I
>> have to confirm how it works with hardware team. Driver doesn't know
>> when status stage was completed. We don't have any event on status
>> stage completion. I haven't checked it yet with tester on this
>> driver.
>
> Let's consider the scenario where you're requesting Test_Packet mode. If
> you start transmitting the test pattern from setup stage, how can you
> even transmit status stage?
>
>>>> +void cdns3_gadget_unconfig(struct cdns3_device *priv_dev)
>>>> +{
>>>> + /* RESET CONFIGURATION */
>>>> + writel(USB_CONF_CFGRST, &priv_dev->regs->usb_conf);
>>>> +
>>>> + cdns3_allow_enable_l1(priv_dev, 0);
>>>> + priv_dev->hw_configured_flag = 0;
>>>> + priv_dev->onchip_mem_allocated_size = 0;
>>>
>>> clear all test modes? Reset ep0 max_packet_size to 512?
>> Test mode should be reset automatically on exit.
>
> on exit? Which exit? Did you test this on USB Reset? Did you run USBCV
> on Super and High speed with any gadget?
>
>> W can't clear this mode in register. It's WAC (write only and auto clear) bit.
>> This function only reset endpoint configuration in controller register.
>> Ep0 max_packet_size should be unchanged here. Ep0 max_packet it's updated on
>> Connect/Disconnect/Reset events.
>
> right, and this is called for both reset and disconnect (see below). If
> you're telling me that test mode and ep0 wMaxPacketSize is handled
> elsewhere, that's fine.
>
> + /* Disconnection detected */
> + if (usb_ists & (USB_ISTS_DIS2I | USB_ISTS_DISI)) {
> + if (priv_dev->gadget_driver &&
> + priv_dev->gadget_driver->disconnect) {
> + spin_unlock(&priv_dev->lock);
> + priv_dev->gadget_driver->disconnect(&priv_dev->gadget);
> + spin_lock(&priv_dev->lock);
> + }
> +
> + priv_dev->gadget.speed = USB_SPEED_UNKNOWN;
> + usb_gadget_set_state(&priv_dev->gadget, USB_STATE_NOTATTACHED);
> + cdns3_gadget_unconfig(priv_dev);
> + }
> +
> + /* reset*/
> + if (usb_ists & (USB_ISTS_UWRESI | USB_ISTS_UHRESI | USB_ISTS_U2RESI)) {
> + /*read again to check the actuall speed*/
> + speed = cdns3_get_speed(priv_dev);
> + usb_gadget_set_state(&priv_dev->gadget, USB_STATE_DEFAULT);
> + priv_dev->gadget.speed = speed;
> + cdns3_gadget_unconfig(priv_dev);
> + cdns3_ep0_config(priv_dev);
> + }
>
>
>> Maybe this function should be called cdns3_hw_reset_eps_config.
>
> perhaps
>
>> It doesn't unconfigure whole gadget but only reset endpoints configuration kept by
>> controller.
>> I will change this function.
>
> ok
>
>>>> +static irqreturn_t cdns3_device_irq_handler(int irq, void *data)
>>>> +{
>>>> + struct cdns3_device *priv_dev;
>>>> + struct cdns3 *cdns = data;
>>>> + irqreturn_t ret = IRQ_NONE;
>>>> + unsigned long flags;
>>>> + u32 reg;
>>>> +
>>>> + priv_dev = cdns->gadget_dev;
>>>> + spin_lock_irqsave(&priv_dev->lock, flags);
>>>
>>> you're already running in hardirq context. Why do you need this lock at
>>> all? I would be better to use the hardirq handler to mask your
>>> interrupts, so they don't fire again, then used the top-half (softirq)
>>> handler to actually handle the interrupts.
>>
>> Yes, spin_lock_irqsave is not necessary here.
>>
>> Do you mean replacing devm_request_irq with a request_threaded_irq ?
>> I have single interrupt line shared between Host, Driver, DRD/OTG.
>> I'm not sure if it will work more efficiently.
>
> The whole idea for running very little in hardirq context is to give the
> scheduler a chance to decide what should run. This is important to
> reduce latency when running with RT patchset applied, for
> example. However, I'll give you that, it's a minor requirement. It's
> just that, to me, it's a small detail that's easy to implement.
>
>>>> + /* check USB device interrupt */
>>>> + reg = readl(&priv_dev->regs->usb_ists);
>>>> + writel(reg, &priv_dev->regs->usb_ists);
>>>> +
>>>> + if (reg) {
>>>> + dev_dbg(priv_dev->dev, "IRQ: usb_ists: %08X\n", reg);
>>>
>>> I strongly advise against using dev_dbg() for debugging. Even more so
>>> inside your IRQ handler.
>> Ok, It's not necessary in this place, especially, that there is invoked trace point
>> inside cdns3_check_usb_interrupt_proceed which makes the same.
>
> overhead. Tracepoints are really, really low overhead. The string
> decoding doesn't happen until you read the trace file.
>

2018-12-14 23:10:53

by kernel test robot

[permalink] [raw]

Subject: Re: [PATCH v1 2/2] usb:cdns3 Add Cadence USB3 DRD Driver

Hi Pawel,

Thank you for the patch! Perhaps something to improve:

[auto build test WARNING on usb/usb-testing]
[also build test WARNING on v4.20-rc6 next-20181214]
[if your patch is applied to the wrong git tree, please drop us a note to help improve the system]

url: https://github.com/0day-ci/linux/commits/Pawel-Laszczak/dt-bindings-add-binding-for-USBSS-DRD-controller/20181211-025348
base: https://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb.git usb-testing
config: m68k-allmodconfig (attached as .config)
compiler: m68k-linux-gnu-gcc (Debian 7.2.0-11) 7.2.0
reproduce:
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# save the attached .config to linux build tree
GCC_VERSION=7.2.0 make.cross ARCH=m68k

All warnings (new ones prefixed by >>):

drivers/usb//cdns3/host.c: In function 'cdns3_host_init':
>> drivers/usb//cdns3/host.c:65:5: warning: "CONFIG_PM" is not defined, evaluates to 0 [-Wundef]
#if CONFIG_PM
^~~~~~~~~

vim +/CONFIG_PM +65 drivers/usb//cdns3/host.c

53
54 int cdns3_host_init(struct cdns3 *cdns)
55 {
56 struct cdns3_role_driver *rdrv;
57
58 rdrv = devm_kzalloc(cdns->dev, sizeof(*rdrv), GFP_KERNEL);
59 if (!rdrv)
60 return -ENOMEM;
61
62 rdrv->start = __cdns3_host_init;
63 rdrv->stop = cdns3_host_exit;
64 rdrv->state = CDNS3_ROLE_STATE_INACTIVE;
> 65 #if CONFIG_PM

---
0-DAY kernel test infrastructure Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all Intel Corporation

Attachments:

(No filename) (1.66 kB)
.config.gz (46.56 kB)
Download all attachments

2018-12-16 13:05:07

[permalink] [raw]

Subject: RE: [PATCH v1 2/2] usb:cdns3 Add Cadence USB3 DRD Driver

Hi Peter

>On Mon, Dec 10, 2018 at 8:55 PM Pawel Laszczak <[email protected]> wrote:
>>
>> This patch introduce new Cadence USBSS DRD driver
>> to linux kernel.
>>
>> The Cadence USBSS DRD Driver is a highly
>> configurable IP Core which can be
>> instantiated as Dual-Role Device (DRD),
>> Peripheral Only and Host Only (XHCI)
>> configurations.
>>
>> The current driver has been validated with
>> FPGA burned. We have support for PCIe
>> bus, which is used on FPGA prototyping.
>>
>> The host side of USBSS-DRD controller is compliance
>> with XHCI specification, so it works with
>> standard XHCI linux driver.
>>
>> Signed-off-by: Pawel Laszczak <[email protected]>
>> ---
>
>I have compiled it at my ARM64 platform, and will give you more feedback after
>adding platform support. Below is one compile warning, please fix
>
> CC drivers/usb/cdns3/host.o
> AR drivers/usb/cdns3/cdns3-pci.o
>/home/b29397/work/projects/linux-imx/drivers/usb/cdns3/gadget.c: In
>function ‘cdns3_gadget_ep_disable’:
>/home/b29397/work/projects/linux-imx/drivers/usb/cdns3/gadget.c:1122:19:
>warning: ‘priv_dev’ may be used uninitialized in this function
>[-Wmaybe-uninitialized]
> dev_dbg(priv_dev->dev, "usbss: invalid parameters\n");
> ^~
> AR drivers/usb/cdns3/cdns3.o
>

I found this also. Some time ago I changed
pr_err("usbss: invalid parameters\n");
to
dev_err(priv_dev->dev, "usbss: invalid parameters\n");

In cdns3_gadget_ep_disable function and it was mistake.

I don't know why I didn't see this warning before posting patch.

Cheers
Pawel

2018-12-17 06:03:47

[permalink] [raw]

Subject: RE: [PATCH v1 2/2] usb:cdns3 Add Cadence USB3 DRD Driver

Hi,

>
>On 12/12/18 12:22 PM, Felipe Balbi wrote:
>>
>> Hi
>>
>> Pawel Laszczak <[email protected]> writes:
>>>>> + cdns->phy = devm_phy_get(dev, "cdns3,usbphy");
>>>>> + if (IS_ERR(cdns->phy)) {
>>>>> + ret = PTR_ERR(cdns->phy);
>>>>> + if (ret == -ENOSYS || ret == -ENODEV) {
>>>>
>>>> Are you sure you can get ENOSYS here? Have you checked output of
>>>> checkpatch --strict?
>>>> -:852: WARNING: ENOSYS means 'invalid syscall nr' and nothing else
>>>
>>> Yes this error code can be returned by related to phy function if
>>> CONFIG_GENERIC_PHY is disabled.
>>>
>>> I have seen this warning in output of checkpatch --strict .
>>
>> Kishon, seems like you shouldn't be using that error value.
>
>hmm, yeah should change the return value to -ENODEV when GENERIC_PHY is disabled.
>

So I will remove this ENOSYS from next patch. I assume that it will be removed also from generic phy driver.

Thanks,
Pawel

2018-12-17 11:57:51

[permalink] [raw]

Subject: RE: [PATCH v1 2/2] usb:cdns3 Add Cadence USB3 DRD Driver

Hi,

Pawel Laszczak <[email protected]> writes:
>>>>> +static irqreturn_t cdns3_device_irq_handler(int irq, void *data)
>>>>> +{
>>>>> + struct cdns3_device *priv_dev;
>>>>> + struct cdns3 *cdns = data;
>>>>> + irqreturn_t ret = IRQ_NONE;
>>>>> + unsigned long flags;
>>>>> + u32 reg;
>>>>> +
>>>>> + priv_dev = cdns->gadget_dev;
>>>>> + spin_lock_irqsave(&priv_dev->lock, flags);
>>>>
>>>>you're already running in hardirq context. Why do you need this lock at
>>>>all? I would be better to use the hardirq handler to mask your
>>>>interrupts, so they don't fire again, then used the top-half (softirq)
>>>>handler to actually handle the interrupts.
>>>
>>> Yes, spin_lock_irqsave is not necessary here.
>>>
>>> Do you mean replacing devm_request_irq with a request_threaded_irq ?
>>> I have single interrupt line shared between Host, Driver, DRD/OTG.
>>> I'm not sure if it will work more efficiently.
>>
>>The whole idea for running very little in hardirq context is to give the
>>scheduler a chance to decide what should run. This is important to
>>reduce latency when running with RT patchset applied, for
>>example. However, I'll give you that, it's a minor requirement. It's
>>just that, to me, it's a small detail that's easy to implement.
>
> I will do it in PATCH v2 or PATCH v3.
> I need to post next version before 24 of December, so if I can do it
> before this date then it will be in PATCH v2.

Take your time :-) Nothing will happen until next year. I already sent
my pull request for v4.21 and a large chunk of the community takes a few
days off during the holiday season.

There's really no rush from a community stand point.

--
balbi

Attachments:

signature.asc (847.00 B)

2018-12-17 12:24:07

[permalink] [raw]

Subject: RE: [PATCH v1 2/2] usb:cdns3 Add Cadence USB3 DRD Driver

Hi Felipe
>
>Pawel Laszczak <[email protected]> writes:
><snip>
>
>>>> + case USB_REQ_SET_ISOCH_DELAY:
>>>> + sprintf(str, "Set Isochronous Delay Delay: %d ns", wValue);
>>>> + break;
>>>> + default:
>>>> + sprintf(str,
>>>> + "SETUP BRT: %02x BR: %02x V: %04x I: %04x L: %04x\n",
>>>> + bRequestType, bRequest,
>>>> + wValue, wIndex, wLength);
>>>> + }
>>>> +
>>>> + return str;
>>>> +}
>>>
>>>All of these are a flat out copy of dwc3's implementation. It's much,
>>>much better to turn dwc3's implementation into a generic, reusable
>>>library function then spinning your own as a duplicated effort.
>> I agree,
>> It would be nice to have a set of decoding function in some generic library. It could be used
>> also by other drivers.
>> Who should do this ?
>
>since you're the first to reuse it, then it should be you :-)

So I can prepare debug.h in drivers/usb/gadget directory.

Function form drivers/usb/dwc3/debug.h that could be common are:

static inline void dwc3_decode_get_status(__u8 t, __u16 i, __u16 l, char *str)
static inline void dwc3_decode_get_set_descriptor(__u8 t, __u8 b, __u16 v,
__u16 i, __u16 l, char *str)
static inline void dwc3_decode_set_clear_feature(__u8 t, __u8 b, __u16 v, __u16 i, char *str)
static inline void dwc3_decode_set_address(__u16 v, char *str)
static inline void dwc3_decode_get_set_descriptor(__u8 t, __u8 b, __u16 v, __u16 i, __u16 l, char *str)
static inline void dwc3_decode_get_configuration(__u16 l, char *str)
static inline void dwc3_decode_set_configuration(__u8 v, char *str)
static inline void dwc3_decode_get_intf(__u16 i, __u16 l, char *str)
static inline void dwc3_decode_set_intf(__u8 v, __u16 i, char *str)
static inline void dwc3_decode_synch_frame(__u16 i, __u16 l, char *str)
static inline const char *dwc3_decode_ctrl(char *str, __u8 bRequestType, __u8 bRequest, __u16 wValue, __u16 wIndex, __u16 wLength)

After changed it could looks like:
static inline void usb_decode_get_status(__u8 bRequestType, __u16 wIndex, __u16 wLength, char *str)
static inline void usb _decode_get_set_descriptor(__u8 bRequestType, __u8 bRequest, __u16 wValue,
__u16 wIndex, __u16 wLength, char *str)
static inline void usb_decode_set_clear_feature(__u8 bRequestType, __u8 bRequest, __u16 wValue, __u16 wIndex, char *str)
static inline void usb_decode_set_address(__u16 v, char *str)
static inline void usb_decode_get_set_descriptor(__u8 bRequestType, __u8 bRequest, __u16 wValue, __u16 wIndex, __u16 wLength, char *str)
static inline void usb_decode_get_configuration(__u16 wLength, char *str)
static inline void usb_decode_set_configuration(__u8 wValue, char *str)
static inline void usb_decode_get_intf(__u16 wIndex, __u16 wLength, char *str)
static inline void usb_decode_set_intf(__u8 wValue, __u16 wIndex, char *str)
static inline void usb_decode_synch_frame(__u16 wIndex, __u16 wLength, char *str)
static inline const char * usb _decode_ctrl(char *str, __u8 bRequestType, __u8 bRequest, __u16 wValue, __u16 wIndex, __u16 wLength)

Sorry but I prefer some more significant names :)

For me functions in drivers/usb/dwc3/debug.h looks ok, but I think that could be better to
add additional usb_decode_test_mode and usb_decode_device_feature and little simplify usb_decode_get_set_descriptor.

What do you think about this?

One more question.
Can I add drivers/usb/gadget/debug.h file as part of my set patches, or this should be done as separate, new patch ?

Cheers,
Pawel

2018-12-17 12:25:00

[permalink] [raw]

Subject: RE: [PATCH v1 2/2] usb:cdns3 Add Cadence USB3 DRD Driver

Hi,

Pawel Laszczak <[email protected]> writes:
>>>>> + case USB_REQ_SET_ISOCH_DELAY:
>>>>> + sprintf(str, "Set Isochronous Delay Delay: %d ns", wValue);
>>>>> + break;
>>>>> + default:
>>>>> + sprintf(str,
>>>>> + "SETUP BRT: %02x BR: %02x V: %04x I: %04x L: %04x\n",
>>>>> + bRequestType, bRequest,
>>>>> + wValue, wIndex, wLength);
>>>>> + }
>>>>> +
>>>>> + return str;
>>>>> +}
>>>>
>>>>All of these are a flat out copy of dwc3's implementation. It's much,
>>>>much better to turn dwc3's implementation into a generic, reusable
>>>>library function then spinning your own as a duplicated effort.
>>> I agree,
>>> It would be nice to have a set of decoding function in some generic library. It could be used
>>> also by other drivers.
>>> Who should do this ?
>>
>>since you're the first to reuse it, then it should be you :-)
>
> So I can prepare debug.h in drivers/usb/gadget directory.

no, not there. Host drivers can rely on it too, if they want. Let's have
it on drivers/usb/common/debug.c (or some other name) and a header under include/linux/usb/

> Function form drivers/usb/dwc3/debug.h that could be common are:
>
> static inline void dwc3_decode_get_status(__u8 t, __u16 i, __u16 l, char *str)
> static inline void dwc3_decode_get_set_descriptor(__u8 t, __u8 b, __u16 v,
> __u16 i, __u16 l, char *str)
> static inline void dwc3_decode_set_clear_feature(__u8 t, __u8 b, __u16 v, __u16 i, char *str)
> static inline void dwc3_decode_set_address(__u16 v, char *str)
> static inline void dwc3_decode_get_set_descriptor(__u8 t, __u8 b, __u16 v, __u16 i, __u16 l, char *str)
> static inline void dwc3_decode_get_configuration(__u16 l, char *str)
> static inline void dwc3_decode_set_configuration(__u8 v, char *str)
> static inline void dwc3_decode_get_intf(__u16 i, __u16 l, char *str)
> static inline void dwc3_decode_set_intf(__u8 v, __u16 i, char *str)
> static inline void dwc3_decode_synch_frame(__u16 i, __u16 l, char *str)
> static inline const char *dwc3_decode_ctrl(char *str, __u8 bRequestType, __u8 bRequest, __u16 wValue, __u16 wIndex, __u16 wLength)
>
> After changed it could looks like:
> static inline void usb_decode_get_status(__u8 bRequestType, __u16 wIndex, __u16 wLength, char *str)
> static inline void usb _decode_get_set_descriptor(__u8 bRequestType, __u8 bRequest, __u16 wValue,
> __u16 wIndex, __u16 wLength, char *str)
> static inline void usb_decode_set_clear_feature(__u8 bRequestType, __u8 bRequest, __u16 wValue, __u16 wIndex, char *str)
> static inline void usb_decode_set_address(__u16 v, char *str)
> static inline void usb_decode_get_set_descriptor(__u8 bRequestType, __u8 bRequest, __u16 wValue, __u16 wIndex, __u16 wLength, char *str)
> static inline void usb_decode_get_configuration(__u16 wLength, char *str)
> static inline void usb_decode_set_configuration(__u8 wValue, char *str)
> static inline void usb_decode_get_intf(__u16 wIndex, __u16 wLength, char *str)
> static inline void usb_decode_set_intf(__u8 wValue, __u16 wIndex, char *str)
> static inline void usb_decode_synch_frame(__u16 wIndex, __u16 wLength, char *str)
> static inline const char * usb _decode_ctrl(char *str, __u8 bRequestType, __u8 bRequest, __u16 wValue, __u16 wIndex, __u16 wLength)
>
> Sorry but I prefer some more significant names :)

meh, no worries

> For me functions in drivers/usb/dwc3/debug.h looks ok, but I think that could be better to
> add additional usb_decode_test_mode and usb_decode_device_feature and little simplify usb_decode_get_set_descriptor.

sure, just propose patches. Just make sure that your patches do a single
thing per patch. Meaning, first you add a patch moving functions to
drivers/usb/common and updating dwc3, then you add another to decode
test mode (then update dwc3), and another simplifying set_descriptor.

> What do you think about this?
>
> One more question.
> Can I add drivers/usb/gadget/debug.h file as part of my set patches, or this should be done as separate, new patch ?

Your first patch moving functions from dwc3 should move them somewhere ;)

--
balbi

Attachments:

signature.asc (847.00 B)

2018-12-17 14:00:00

[permalink] [raw]

Subject: RE: [PATCH v1 2/2] usb:cdns3 Add Cadence USB3 DRD Driver

Hi,

>
>>>> +static irqreturn_t cdns3_device_irq_handler(int irq, void *data)
>>>> +{
>>>> + struct cdns3_device *priv_dev;
>>>> + struct cdns3 *cdns = data;
>>>> + irqreturn_t ret = IRQ_NONE;
>>>> + unsigned long flags;
>>>> + u32 reg;
>>>> +
>>>> + priv_dev = cdns->gadget_dev;
>>>> + spin_lock_irqsave(&priv_dev->lock, flags);
>>>
>>>you're already running in hardirq context. Why do you need this lock at
>>>all? I would be better to use the hardirq handler to mask your
>>>interrupts, so they don't fire again, then used the top-half (softirq)
>>>handler to actually handle the interrupts.
>>
>> Yes, spin_lock_irqsave is not necessary here.
>>
>> Do you mean replacing devm_request_irq with a request_threaded_irq ?
>> I have single interrupt line shared between Host, Driver, DRD/OTG.
>> I'm not sure if it will work more efficiently.
>
>The whole idea for running very little in hardirq context is to give the
>scheduler a chance to decide what should run. This is important to
>reduce latency when running with RT patchset applied, for
>example. However, I'll give you that, it's a minor requirement. It's
>just that, to me, it's a small detail that's easy to implement.

I will do it in PATCH v2 or PATCH v3.
I need to post next version before 24 of December, so if I can do it
before this date then it will be in PATCH v2.

Thanks
Pawel

2018-12-21 06:55:57

by Rob Herring

[permalink] [raw]

Subject: Re: [PATCH v1 1/2] dt-bindings: add binding for USBSS-DRD controller.

On Mon, Dec 10, 2018 at 12:39:14PM +0000, Pawel Laszczak wrote:
> This patch aim at documenting USB related dt-bindings for the
> Cadence USBSS-DRD controller.
>
> Signed-off-by: Pawel Laszczak <[email protected]>
> ---
> .../devicetree/bindings/usb/cdns3-usb.txt | 31 +++++++++++++++++++
> 1 file changed, 31 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/usb/cdns3-usb.txt
>
> diff --git a/Documentation/devicetree/bindings/usb/cdns3-usb.txt b/Documentation/devicetree/bindings/usb/cdns3-usb.txt
> new file mode 100644
> index 000000000000..ae4a255f0b10
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/usb/cdns3-usb.txt

cdns-usb3.txt?

> @@ -0,0 +1,31 @@
> +Binding for the Cadence USBSS-DRD controller
> +
> +Required properties:
> + - reg: Physical base address and size of the controller's register areas.
> + Controller has 3 different regions:
> + region 1 - HOST registers area
> + region 2 - DEVICE registers area
> + region 3 - OTG/DRD registers area
> + - compatible: Should contain: "cdns,usb3"

Only 1 version of the IP block?

> + - interrupts: Interrupt specifier. Refer to interrupt bindings.
> + Driver supports only single interrupt line.
> + This single interrupt is shared between Device,
> + host and OTG/DRD part of driver.
> +
> +Optional propertiesi:

typo

> + - maximum-speed : valid arguments are "super-speed", "high-speed" and
> + "full-speed"; refer to usb/generic.txt
> + - dr_mode: Should be one of "host", "peripheral" or "otg".
> + - phys: reference to the USB PHY
> + - phy-names: name of the USB PHY, should be "cdns3,usbphy"

Don't need -names when there is only one.

> +
> +
> +Example:
> + usb@f3000000 {
> + compatible = "cdns,usb3";
> + interrupts = <USB_IRQ 7 IRQ_TYPE_LEVEL_HIGH>;
> + reg = <0xf3000000 0x10000 //memory area for HOST registers
> + 0xf3010000 0x10000 //memory area for DEVICE registers
> + 0xf3020000 0x10000>; //memory area for OTG/DRD registers
> + };
> +
> --
> 2.17.1
>

2018-12-23 16:33:42

[permalink] [raw]

Subject: RE: [PATCH v1 1/2] dt-bindings: add binding for USBSS-DRD controller.

Hi Rob,

>On Mon, Dec 10, 2018 at 12:39:14PM +0000, Pawel Laszczak wrote:
>> This patch aim at documenting USB related dt-bindings for the
>> Cadence USBSS-DRD controller.
>>
>> Signed-off-by: Pawel Laszczak <[email protected]>
>> ---
>> .../devicetree/bindings/usb/cdns3-usb.txt | 31 +++++++++++++++++++
>> 1 file changed, 31 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/usb/cdns3-usb.txt
>>
>> diff --git a/Documentation/devicetree/bindings/usb/cdns3-usb.txt b/Documentation/devicetree/bindings/usb/cdns3-usb.txt
>> new file mode 100644
>> index 000000000000..ae4a255f0b10
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/usb/cdns3-usb.txt
>
>cdns-usb3.txt?

In all functions we use prefix cdns3, so it was a reason for cdns3-usb.txt.
I agree with you and I think that cdns-usb3.txt in this place will be better.
3 in cdns3 could be associated with company name, but that's not true.

>
>> @@ -0,0 +1,31 @@
>> +Binding for the Cadence USBSS-DRD controller
>> +
>> +Required properties:
>> + - reg: Physical base address and size of the controller's register areas.
>> + Controller has 3 different regions:
>> + region 1 - HOST registers area
>> + region 2 - DEVICE registers area
>> + region 3 - OTG/DRD registers area
>> + - compatible: Should contain: "cdns,usb3"
>
>Only 1 version of the IP block?

I will add one more. Now I know that we should have
at least one additional version.
Controller version will be recognized at runtime, but in my opinion
we should also have information about this in dt-binding documentation.
>
>> + - interrupts: Interrupt specifier. Refer to interrupt bindings.
>> + Driver supports only single interrupt line.
>> + This single interrupt is shared between Device,
>> + host and OTG/DRD part of driver.
>> +
>> +Optional propertiesi:
>
>typo
Thank, I know that already. Someone has already reported me this typo.
"i" - insert mode in vim :)
>
>> + - maximum-speed : valid arguments are "super-speed", "high-speed" and
>> + "full-speed"; refer to usb/generic.txt
>> + - dr_mode: Should be one of "host", "peripheral" or "otg".
>> + - phys: reference to the USB PHY
>> + - phy-names: name of the USB PHY, should be "cdns3,usbphy"
>
>Don't need -names when there is only one.

But in the future probably we will need to add next phy version.
So maybe it's better to leave this name ?

>
>> +
>> +
>> +Example:
>> + usb@f3000000 {
>> + compatible = "cdns,usb3";
>> + interrupts = <USB_IRQ 7 IRQ_TYPE_LEVEL_HIGH>;
>> + reg = <0xf3000000 0x10000 //memory area for HOST registers
>> + 0xf3010000 0x10000 //memory area for DEVICE registers
>> + 0xf3020000 0x10000>; //memory area for OTG/DRD registers
>> + };
>> +
>> --
>> 2.17.1
>>

Thanks for comments
Cheers,
Pawel

2018-12-28 07:59:41

by Rob Herring

[permalink] [raw]

Subject: Re: [PATCH v1 1/2] dt-bindings: add binding for USBSS-DRD controller.

On Sat, Dec 22, 2018 at 4:24 PM Pawel Laszczak <[email protected]> wrote:
>
> Hi Rob,
>
> >On Mon, Dec 10, 2018 at 12:39:14PM +0000, Pawel Laszczak wrote:
> >> This patch aim at documenting USB related dt-bindings for the
> >> Cadence USBSS-DRD controller.
> >>
> >> Signed-off-by: Pawel Laszczak <[email protected]>

[...]

> >> + - phys: reference to the USB PHY
> >> + - phy-names: name of the USB PHY, should be "cdns3,usbphy"
> >
> >Don't need -names when there is only one.
>
> But in the future probably we will need to add next phy version.
> So maybe it's better to leave this name ?

'-names' are for when there is more than one phy connected, not
different phy versions. For example, if you had separate phys for HS
and SS.

Rob

2018-12-31 05:38:20