This is a patch series for OCOTP driver for Sunplus SP7021 SoC.
Sunplus SP7021 is an ARM Cortex A7 (4 cores) based SoC. It integrates
many peripherals (ex: UART, I2C, SPI, SDIO, eMMC, USB, SD Card and
etc.) into a single chip. It is designed for industrial control.
Refer to:
https://sunplus-tibbo.atlassian.net/wiki/spaces/doc/overview
https://tibbo.com/store/plus1.html
Vincent Shih (2):
nvmem: Add driver for OCOTP in Sunplus SP7021
dt-bindings: nvmem: Add bindings doc for Sunplus OCOTP driver
.../bindings/nvmem/sunplus,sp7021-ocotp.yaml | 86 ++++++++
MAINTAINERS | 6 +
drivers/nvmem/Kconfig | 12 ++
drivers/nvmem/Makefile | 2 +
drivers/nvmem/sunplus-ocotp.c | 228 +++++++++++++++++++++
5 files changed, 334 insertions(+)
create mode 100644 Documentation/devicetree/bindings/nvmem/sunplus,sp7021-ocotp.yaml
create mode 100644 drivers/nvmem/sunplus-ocotp.c
--
2.7.4
Add driver for OCOTP in Sunplus SP7021
Signed-off-by: Vincent Shih <[email protected]>
---
Changes in v3:
- Addressed the comments by Mr. Srinivas Kandagatla.
MAINTAINERS | 5 +
drivers/nvmem/Kconfig | 12 +++
drivers/nvmem/Makefile | 2 +
drivers/nvmem/sunplus-ocotp.c | 228 ++++++++++++++++++++++++++++++++++++++++++
4 files changed, 247 insertions(+)
create mode 100644 drivers/nvmem/sunplus-ocotp.c
diff --git a/MAINTAINERS b/MAINTAINERS
index 80eebc1..0e6593a 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -17947,6 +17947,11 @@ L: [email protected]
S: Maintained
F: drivers/net/ethernet/dlink/sundance.c
+SUNPLUS OCOTP DRIVER
+M: Vincent Shih <[email protected]>
+S: Maintained
+F: drivers/nvmem/sunplus-ocotp.c
+
SUPERH
M: Yoshinori Sato <[email protected]>
M: Rich Felker <[email protected]>
diff --git a/drivers/nvmem/Kconfig b/drivers/nvmem/Kconfig
index da41461..4559950 100644
--- a/drivers/nvmem/Kconfig
+++ b/drivers/nvmem/Kconfig
@@ -300,4 +300,16 @@ config NVMEM_BRCM_NVRAM
This driver provides support for Broadcom's NVRAM that can be accessed
using I/O mapping.
+config NVMEM_SUNPLUS_OCOTP
+ tristate "Sunplus SoC OTP support"
+ depends on SOC_SP7021 || COMPILE_TEST
+ depends on HAS_IOMEM
+ help
+ This is a driver for the On-chip OTP controller (OCOTP) available
+ on Sunplus SoCs. It provides access to 128 bytes of one-time
+ programmable eFuse.
+
+ This driver can also be built as a module. If so, the module
+ will be called nvmem-sunplus-ocotp.
+
endif
diff --git a/drivers/nvmem/Makefile b/drivers/nvmem/Makefile
index dcbbde3..0f14cd9 100644
--- a/drivers/nvmem/Makefile
+++ b/drivers/nvmem/Makefile
@@ -61,3 +61,5 @@ obj-$(CONFIG_NVMEM_RMEM) += nvmem-rmem.o
nvmem-rmem-y := rmem.o
obj-$(CONFIG_NVMEM_BRCM_NVRAM) += nvmem_brcm_nvram.o
nvmem_brcm_nvram-y := brcm_nvram.o
+obj-$(CONFIG_NVMEM_SUNPLUS_OCOTP) += nvmem_sunplus_ocotp.o
+nvmem_sunplus_ocotp-y := sunplus-ocotp.o
diff --git a/drivers/nvmem/sunplus-ocotp.c b/drivers/nvmem/sunplus-ocotp.c
new file mode 100644
index 0000000..2dc59c2
--- /dev/null
+++ b/drivers/nvmem/sunplus-ocotp.c
@@ -0,0 +1,228 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/*
+ * The OCOTP driver for Sunplus SP7021
+ *
+ * Copyright (C) 2019 Sunplus Technology Inc., All rights reserved.
+ */
+
+#include <linux/bitfield.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/module.h>
+#include <linux/nvmem-provider.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+
+/*
+ * OTP memory
+ * Each bank contains 4 words (32 bits).
+ * Bank 0 starts at offset 0 from the base.
+ */
+
+#define OTP_WORDS_PER_BANK 4
+#define OTP_WORD_SIZE sizeof(u32)
+#define OTP_BIT_ADDR_OF_BANK (8 * OTP_WORD_SIZE * OTP_WORDS_PER_BANK)
+#define QAC628_OTP_NUM_BANKS 8
+#define QAC628_OTP_SIZE (QAC628_OTP_NUM_BANKS * OTP_WORDS_PER_BANK * OTP_WORD_SIZE)
+#define OTP_READ_TIMEOUT_US 200000
+
+/* HB_GPIO */
+#define ADDRESS_8_DATA 0x20
+
+/* OTP_RX */
+#define OTP_CONTROL_2 0x48
+#define OTP_RD_PERIOD GENMASK(15, 8)
+#define OTP_RD_PERIOD_MASK ~GENMASK(15, 8)
+#define CPU_CLOCK FIELD_PREP(OTP_RD_PERIOD, 30)
+#define SEL_BAK_KEY2 BIT(5)
+#define SEL_BAK_KEY2_MASK ~BIT(5)
+#define SW_TRIM_EN BIT(4)
+#define SW_TRIM_EN_MASK ~BIT(4)
+#define SEL_BAK_KEY BIT(3)
+#define SEL_BAK_KEY_MASK ~BIT(3)
+#define OTP_READ BIT(2)
+#define OTP_LOAD_SECURE_DATA BIT(1)
+#define OTP_LOAD_SECURE_DATA_MASK ~BIT(1)
+#define OTP_DO_CRC BIT(0)
+#define OTP_DO_CRC_MASK ~BIT(0)
+#define OTP_STATUS 0x4c
+#define OTP_READ_DONE BIT(4)
+#define OTP_READ_DONE_MASK ~BIT(4)
+#define OTP_LOAD_SECURE_DONE_MASK ~BIT(2)
+#define OTP_READ_ADDRESS 0x50
+
+enum base_type {
+ HB_GPIO,
+ OTPRX,
+ BASEMAX,
+};
+
+struct sp_ocotp_priv {
+ struct device *dev;
+ void __iomem *base[BASEMAX];
+ struct clk *clk;
+};
+
+struct sp_ocotp_data {
+ int size;
+};
+
+const struct sp_ocotp_data sp_otp_v0 = {
+ .size = QAC628_OTP_SIZE,
+};
+
+static int sp_otp_read_real(struct sp_ocotp_priv *otp, int addr, char *value)
+{
+ unsigned int addr_data;
+ unsigned int byte_shift;
+ unsigned int status;
+ int ret;
+
+ addr_data = addr % (OTP_WORD_SIZE * OTP_WORDS_PER_BANK);
+ addr_data = addr_data / OTP_WORD_SIZE;
+
+ byte_shift = addr % (OTP_WORD_SIZE * OTP_WORDS_PER_BANK);
+ byte_shift = byte_shift % OTP_WORD_SIZE;
+
+ addr = addr / (OTP_WORD_SIZE * OTP_WORDS_PER_BANK);
+ addr = addr * OTP_BIT_ADDR_OF_BANK;
+
+ writel(readl(otp->base[OTPRX] + OTP_STATUS) & OTP_READ_DONE_MASK &
+ OTP_LOAD_SECURE_DONE_MASK, otp->base[OTPRX] + OTP_STATUS);
+ writel(addr, otp->base[OTPRX] + OTP_READ_ADDRESS);
+ writel(readl(otp->base[OTPRX] + OTP_CONTROL_2) | OTP_READ,
+ otp->base[OTPRX] + OTP_CONTROL_2);
+ writel(readl(otp->base[OTPRX] + OTP_CONTROL_2) & SEL_BAK_KEY2_MASK & SW_TRIM_EN_MASK
+ & SEL_BAK_KEY_MASK & OTP_LOAD_SECURE_DATA_MASK & OTP_DO_CRC_MASK,
+ otp->base[OTPRX] + OTP_CONTROL_2);
+ writel((readl(otp->base[OTPRX] + OTP_CONTROL_2) & OTP_RD_PERIOD_MASK) | CPU_CLOCK,
+ otp->base[OTPRX] + OTP_CONTROL_2);
+
+ ret = readl_poll_timeout(otp->base[OTPRX] + OTP_STATUS, status,
+ status & OTP_READ_DONE, 10, OTP_READ_TIMEOUT_US);
+
+ if (ret < 0)
+ return ret;
+
+ *value = (readl(otp->base[HB_GPIO] + ADDRESS_8_DATA + addr_data * OTP_WORD_SIZE)
+ >> (8 * byte_shift)) & 0xff;
+
+ return ret;
+}
+
+static int sp_ocotp_read(void *priv, unsigned int offset, void *value, size_t bytes)
+{
+ struct sp_ocotp_priv *otp = priv;
+ unsigned int addr;
+ char *buf = value;
+ char val[4];
+ int ret;
+
+ ret = clk_enable(otp->clk);
+ if (ret)
+ return ret;
+
+ *buf = 0;
+ for (addr = offset; addr < (offset + bytes); addr++) {
+ ret = sp_otp_read_real(otp, addr, val);
+ if (ret < 0) {
+ dev_err(otp->dev, "OTP read fail:%d at %d", ret, addr);
+ goto disable_clk;
+ }
+
+ *buf++ = *val;
+ }
+
+disable_clk:
+ clk_disable(otp->clk);
+
+ return ret;
+}
+
+static struct nvmem_config sp_ocotp_nvmem_config = {
+ .name = "sp-ocotp",
+ .read_only = true,
+ .word_size = 1,
+ .size = QAC628_OTP_SIZE,
+ .stride = 1,
+ .reg_read = sp_ocotp_read,
+ .owner = THIS_MODULE,
+};
+
+static int sp_ocotp_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct nvmem_device *nvmem;
+ struct sp_ocotp_priv *otp;
+ struct resource *res;
+ int ret;
+
+ otp = devm_kzalloc(dev, sizeof(*otp), GFP_KERNEL);
+ if (!otp)
+ return -ENOMEM;
+
+ otp->dev = dev;
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "hb_gpio");
+ otp->base[HB_GPIO] = devm_ioremap_resource(dev, res);
+ if (IS_ERR(otp->base[HB_GPIO]))
+ return PTR_ERR(otp->base[HB_GPIO]);
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "otprx");
+ otp->base[OTPRX] = devm_ioremap_resource(dev, res);
+ if (IS_ERR(otp->base[OTPRX]))
+ return PTR_ERR(otp->base[OTPRX]);
+
+ otp->clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(otp->clk))
+ return dev_err_probe(&pdev->dev, PTR_ERR(otp->clk),
+ "devm_clk_get fail\n");
+
+ ret = clk_prepare(otp->clk);
+ if (ret < 0) {
+ dev_err(dev, "failed to prepare clk: %d\n", ret);
+ return ret;
+ }
+
+ sp_ocotp_nvmem_config.priv = otp;
+ sp_ocotp_nvmem_config.dev = dev;
+
+ nvmem = devm_nvmem_register(dev, &sp_ocotp_nvmem_config);
+ if (IS_ERR(nvmem))
+ return dev_err_probe(&pdev->dev, PTR_ERR(nvmem),
+ "register nvmem device fail\n");
+
+ platform_set_drvdata(pdev, nvmem);
+
+ dev_dbg(dev, "banks:%d x wpb:%d x wsize:%d = %d",
+ (int)QAC628_OTP_NUM_BANKS, (int)OTP_WORDS_PER_BANK,
+ (int)OTP_WORD_SIZE, (int)QAC628_OTP_SIZE);
+
+ dev_info(dev, "by Sunplus (C) 2020");
+
+ return 0;
+}
+
+static const struct of_device_id sp_ocotp_dt_ids[] = {
+ { .compatible = "sunplus,sp7021-ocotp", .data = &sp_otp_v0 },
+ { }
+};
+MODULE_DEVICE_TABLE(of, sp_ocotp_dt_ids);
+
+static struct platform_driver sp_otp_driver = {
+ .probe = sp_ocotp_probe,
+ .driver = {
+ .name = "sunplus,sp7021-ocotp",
+ .of_match_table = sp_ocotp_dt_ids,
+ }
+};
+module_platform_driver(sp_otp_driver);
+
+MODULE_AUTHOR("Vincent Shih <[email protected]>");
+MODULE_DESCRIPTION("Sunplus On-Chip OTP driver");
+MODULE_LICENSE("GPL");
+
--
2.7.4
Add bindings doc for Sunplus OCOTP driver
Reviewed-by: Rob Herring <[email protected]>
Signed-off-by: Vincent Shih <[email protected]>
---
Changes in v3
- No change
.../bindings/nvmem/sunplus,sp7021-ocotp.yaml | 86 ++++++++++++++++++++++
MAINTAINERS | 1 +
2 files changed, 87 insertions(+)
create mode 100644 Documentation/devicetree/bindings/nvmem/sunplus,sp7021-ocotp.yaml
diff --git a/Documentation/devicetree/bindings/nvmem/sunplus,sp7021-ocotp.yaml b/Documentation/devicetree/bindings/nvmem/sunplus,sp7021-ocotp.yaml
new file mode 100644
index 0000000..4b28f37
--- /dev/null
+++ b/Documentation/devicetree/bindings/nvmem/sunplus,sp7021-ocotp.yaml
@@ -0,0 +1,86 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (C) Sunplus Co., Ltd. 2021
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/nvmem/sunplus,sp7021-ocotp.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: On-Chip OTP Memory for Sunplus SP7021
+
+maintainers:
+ - Vincent Shih <[email protected]>
+
+allOf:
+ - $ref: "nvmem.yaml#"
+
+properties:
+ compatible:
+ const: sunplus,sp7021-ocotp
+
+ reg:
+ maxItems: 2
+
+ reg-names:
+ items:
+ - const: hb_gpio
+ - const: otprx
+
+ clocks:
+ maxItems: 1
+
+ "#address-cells":
+ const: 1
+
+ "#size-cells":
+ const: 1
+
+ thermal-calibration:
+ type: object
+ description: thermal calibration values
+
+ disconnect-voltage:
+ type: object
+ description: disconnect voltages of usb2 port 0 and port 1
+
+ mac-address0:
+ type: object
+ description: MAC address of ethernet port 0
+
+ mac-address1:
+ type: object
+ description: MAC address of ethernet port 1
+
+required:
+ - compatible
+ - reg
+ - reg-names
+ - clocks
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/sp-sp7021.h>
+
+ otp: otp@9c00af00 {
+ compatible = "sunplus,sp7021-ocotp";
+ reg = <0x9c00af00 0x34>, <0x9c00af80 0x58>;
+ reg-names = "hb_gpio", "otprx";
+ clocks = <&clks OTPRX>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+ therm_calib: thermal-calibration@14 {
+ reg = <0x14 0x3>;
+ };
+ disc_vol: disconnect-voltage@18 {
+ reg = <0x18 0x2>;
+ };
+ mac_addr0: mac-address0@34 {
+ reg = <0x34 0x6>;
+ };
+ mac_addr1: mac-address1@3a {
+ reg = <0x3a 0x6>;
+ };
+ };
+...
diff --git a/MAINTAINERS b/MAINTAINERS
index 0e6593a..2afd1ea 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -17950,6 +17950,7 @@ F: drivers/net/ethernet/dlink/sundance.c
SUNPLUS OCOTP DRIVER
M: Vincent Shih <[email protected]>
S: Maintained
+F: Documentation/devicetree/bindings/nvmem/sunplus,sp7021-ocotp.yaml
F: drivers/nvmem/sunplus-ocotp.c
SUPERH
--
2.7.4
On 22/12/2021 09:12, Vincent Shih wrote:
> This is a patch series for OCOTP driver for Sunplus SP7021 SoC.
>
> Sunplus SP7021 is an ARM Cortex A7 (4 cores) based SoC. It integrates
> many peripherals (ex: UART, I2C, SPI, SDIO, eMMC, USB, SD Card and
> etc.) into a single chip. It is designed for industrial control.
>
> Refer to:
> https://sunplus-tibbo.atlassian.net/wiki/spaces/doc/overview
> https://tibbo.com/store/plus1.html
>
> Vincent Shih (2):
> nvmem: Add driver for OCOTP in Sunplus SP7021
> dt-bindings: nvmem: Add bindings doc for Sunplus OCOTP driver
Applied thanks,
--srini
>
> .../bindings/nvmem/sunplus,sp7021-ocotp.yaml | 86 ++++++++
> MAINTAINERS | 6 +
> drivers/nvmem/Kconfig | 12 ++
> drivers/nvmem/Makefile | 2 +
> drivers/nvmem/sunplus-ocotp.c | 228 +++++++++++++++++++++
> 5 files changed, 334 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/nvmem/sunplus,sp7021-ocotp.yaml
> create mode 100644 drivers/nvmem/sunplus-ocotp.c
>
On Wed, Dec 22, 2021 at 3:12 AM Vincent Shih <[email protected]> wrote:
>
> Add bindings doc for Sunplus OCOTP driver
>
> Reviewed-by: Rob Herring <[email protected]>
> Signed-off-by: Vincent Shih <[email protected]>
> ---
> Changes in v3
> - No change
>
> .../bindings/nvmem/sunplus,sp7021-ocotp.yaml | 86 ++++++++++++++++++++++
> MAINTAINERS | 1 +
> 2 files changed, 87 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/nvmem/sunplus,sp7021-ocotp.yaml
This is now failing in linux-next:
/builds/robherring/linux-dt/Documentation/devicetree/bindings/spi/spi-sunplus-sp7021.example.dt.yaml:
spi@9C002D80: 'clocks-names' is a required property
From schema: /builds/robherring/linux-dt/Documentation/devicetree/bindings/spi/spi-sunplus-sp7021.yaml
Documentation/devicetree/bindings/nvmem/sunplus,sp7021-ocotp.example.dts:19:18:
fatal error: dt-bindings/clock/sp-sp7021.h: No such file or directory
19 | #include <dt-bindings/clock/sp-sp7021.h>
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
compilation terminated.
Please send a fix ASAP.
Rob