Hello,
This short series introduce devicetree bindings and a driver for the ASPEED SD
controller. Please review!
Andrew
Andrew Jeffery (2):
dt-bindings: mmc: Document Aspeed SD controller
mmc: Add support for the ASPEED SD controller
.../bindings/mmc/sdhci-of-aspeed.yaml | 91 ++++++
drivers/mmc/host/Kconfig | 12 +
drivers/mmc/host/Makefile | 1 +
drivers/mmc/host/sdhci-of-aspeed.c | 307 ++++++++++++++++++
4 files changed, 411 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mmc/sdhci-of-aspeed.yaml
create mode 100644 drivers/mmc/host/sdhci-of-aspeed.c
--
2.20.1
The ASPEED SD/SDIO/eMMC controller exposes two slots implementing the
SDIO Host Specification v2.00, with 1 or 4 bit data buses, or an 8 bit
data bus if only a single slot is enabled.
Signed-off-by: Andrew Jeffery <[email protected]>
---
.../bindings/mmc/sdhci-of-aspeed.yaml | 91 +++++++++++++++++++
1 file changed, 91 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mmc/sdhci-of-aspeed.yaml
diff --git a/Documentation/devicetree/bindings/mmc/sdhci-of-aspeed.yaml b/Documentation/devicetree/bindings/mmc/sdhci-of-aspeed.yaml
new file mode 100644
index 000000000000..e98a2ac4d46d
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/sdhci-of-aspeed.yaml
@@ -0,0 +1,91 @@
+# SPDX-License-Identifier: GPL-2.0-or-later
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mmc/sdhci-of-aspeed.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ASPEED SD/SDIO/eMMC Controller
+
+maintainers:
+ - Andrew Jeffery <[email protected]>
+ - Ryan Chen <[email protected]>
+
+description: |+
+ The ASPEED SD/SDIO/eMMC controller exposes two slots implementing the SDIO
+ Host Specification v2.00, with 1 or 4 bit data buses, or an 8 bit data bus if
+ only a single slot is enabled.
+
+ The two slots are supported by a common configuration area. As the SDHCIs for
+ the slots are dependent on the common configuration area, they are described
+ as child nodes.
+
+properties:
+ compatible:
+ enum: [ aspeed,ast2400-sdc, aspeed,ast2500-sdc ]
+ reg:
+ description: Common configuration registers
+ ranges: true
+ clocks:
+ maxItems: 1
+ description: The SD/SDIO controller clock gate
+ sdhci:
+ type: object
+ properties:
+ compatible:
+ allOf:
+ - enum: [ aspeed,ast2400-sdhci, aspeed,ast2500-sdhci ]
+ - const: sdhci
+ reg:
+ description: The SDHCI registers
+ clocks:
+ maxItems: 1
+ description: The SD bus clock
+ slot:
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ - enum: [0, 1]
+ interrupts:
+ maxItems: 1
+ description: The SD interrupt shared between both slots
+ required:
+ - compatible
+ - reg
+ - clocks
+ - slot
+ - interrupts
+
+required:
+ - compatible
+ - reg
+ - ranges
+ - clocks
+
+examples:
+ - |
+ #include <dt-bindings/clock/aspeed-clock.h>
+ sdc@1e740000 {
+ compatible = "aspeed,ast2500-sdc";
+ reg = <0x1e740000 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ clocks = <&syscon ASPEED_CLK_GATE_SDCLK>;
+
+ sdhci0: sdhci@1e740100 {
+ compatible = "aspeed,ast2500-sdhci", "sdhci";
+ reg = <0x1e740100 0x100>;
+ slot = <0>;
+ interrupts = <26>;
+ sdhci,auto-cmd12;
+ clocks = <&syscon ASPEED_CLK_SDIO>;
+ };
+
+ sdhci1: sdhci@1e740200 {
+ compatible = "aspeed,ast2500-sdhci", "sdhci";
+ reg = <0x1e740200 0x100>;
+ slot = <1>;
+ interrupts = <26>;
+ sdhci,auto-cmd12;
+ clocks = <&syscon ASPEED_CLK_SDIO>;
+ };
+ };
--
2.20.1
Add a minimal driver for ASPEED's SD controller, which exposes two
SDHCIs.
The ASPEED design implements a common register set for the SDHCIs, and
moves some of the standard configuration elements out to this common
area (e.g. 8-bit mode, and card detect configuration which is not
currently supported).
The SD controller has a dedicated hardware interrupt that is shared
between the slots. The common register set exposes information on which
slot triggered the interrupt; early revisions of the patch introduced an
irqchip for the register, but reality is it doesn't behave as an
irqchip, and the result fits awkwardly into the irqchip APIs. Instead
I've taken the simple approach of using the IRQ as a shared IRQ with
some minor performance impact for the second slot.
Ryan was the original author of the patch - I've taken his work and
massaged it to drop the irqchip support and rework the devicetree
integration. The driver has been smoke tested under qemu against a
minimal SD controller model and lightly tested on an ast2500-evb.
Signed-off-by: Ryan Chen <[email protected]>
Signed-off-by: Andrew Jeffery <[email protected]>
---
drivers/mmc/host/Kconfig | 12 ++
drivers/mmc/host/Makefile | 1 +
drivers/mmc/host/sdhci-of-aspeed.c | 307 +++++++++++++++++++++++++++++
3 files changed, 320 insertions(+)
create mode 100644 drivers/mmc/host/sdhci-of-aspeed.c
diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
index 931770f17087..2bb5e1264b3d 100644
--- a/drivers/mmc/host/Kconfig
+++ b/drivers/mmc/host/Kconfig
@@ -154,6 +154,18 @@ config MMC_SDHCI_OF_ARASAN
If unsure, say N.
+config MMC_SDHCI_OF_ASPEED
+ tristate "SDHCI OF support for the ASPEED SDHCI controller"
+ depends on MMC_SDHCI_PLTFM
+ depends on OF
+ help
+ This selects the ASPEED Secure Digital Host Controller Interface.
+
+ If you have a controller with this interface, say Y or M here. You
+ also need to enable an appropriate bus interface.
+
+ If unsure, say N.
+
config MMC_SDHCI_OF_AT91
tristate "SDHCI OF support for the Atmel SDMMC controller"
depends on MMC_SDHCI_PLTFM
diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile
index 73578718f119..390ee162fe71 100644
--- a/drivers/mmc/host/Makefile
+++ b/drivers/mmc/host/Makefile
@@ -84,6 +84,7 @@ obj-$(CONFIG_MMC_SDHCI_ESDHC_IMX) += sdhci-esdhc-imx.o
obj-$(CONFIG_MMC_SDHCI_DOVE) += sdhci-dove.o
obj-$(CONFIG_MMC_SDHCI_TEGRA) += sdhci-tegra.o
obj-$(CONFIG_MMC_SDHCI_OF_ARASAN) += sdhci-of-arasan.o
+obj-$(CONFIG_MMC_SDHCI_OF_ASPEED) += sdhci-of-aspeed.o
obj-$(CONFIG_MMC_SDHCI_OF_AT91) += sdhci-of-at91.o
obj-$(CONFIG_MMC_SDHCI_OF_ESDHC) += sdhci-of-esdhc.o
obj-$(CONFIG_MMC_SDHCI_OF_HLWD) += sdhci-of-hlwd.o
diff --git a/drivers/mmc/host/sdhci-of-aspeed.c b/drivers/mmc/host/sdhci-of-aspeed.c
new file mode 100644
index 000000000000..23fad19787db
--- /dev/null
+++ b/drivers/mmc/host/sdhci-of-aspeed.c
@@ -0,0 +1,307 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/* Copyright (C) 2019 ASPEED Technology Inc. */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/io.h>
+#include <linux/mmc/host.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/spinlock.h>
+
+#include "sdhci-pltfm.h"
+
+#define ASPEED_SDC_INFO 0x00
+#define ASPEED_SDC_S1MMC8 BIT(25)
+#define ASPEED_SDC_S0MMC8 BIT(24)
+
+struct aspeed_sdc {
+ struct clk *clk;
+
+ spinlock_t lock;
+ void __iomem *regs;
+};
+
+struct aspeed_sdhci {
+ struct aspeed_sdc *parent;
+ u32 width_mask;
+};
+
+static void aspeed_sdc_bus_width(struct aspeed_sdc *sdc,
+ struct aspeed_sdhci *sdhci, bool bus8)
+{
+ u32 info;
+
+ /* Set/clear 8 bit mode */
+ spin_lock(&sdc->lock);
+ info = readl(sdc->regs + ASPEED_SDC_INFO);
+ if (bus8)
+ info |= sdhci->width_mask;
+ else
+ info &= ~sdhci->width_mask;
+ writel(info, sdc->regs + ASPEED_SDC_INFO);
+ spin_unlock(&sdc->lock);
+}
+
+static void aspeed_sdhci_set_clock(struct sdhci_host *host, unsigned int clock)
+{
+ unsigned long timeout;
+ int div;
+ u16 clk;
+
+ if (clock == host->clock)
+ return;
+
+ sdhci_writew(host, 0, SDHCI_CLOCK_CONTROL);
+
+ if (clock == 0)
+ goto out;
+
+ for (div = 1; div < 256; div *= 2) {
+ if ((host->max_clk / div) <= clock)
+ break;
+ }
+ div >>= 1;
+
+ clk = div << SDHCI_DIVIDER_SHIFT;
+ clk |= SDHCI_CLOCK_INT_EN;
+ sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
+
+ /* Wait max 20 ms */
+ timeout = 20;
+ while (!((clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL))
+ & SDHCI_CLOCK_INT_STABLE)) {
+ if (timeout == 0) {
+ pr_err("%s: Internal clock never stabilised.\n",
+ mmc_hostname(host->mmc));
+ return;
+ }
+ timeout--;
+ mdelay(1);
+ }
+
+ clk |= SDHCI_CLOCK_CARD_EN;
+ sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
+
+out:
+ host->clock = clock;
+}
+
+static void aspeed_sdhci_set_bus_width(struct sdhci_host *host, int width)
+{
+ struct sdhci_pltfm_host *pltfm_priv;
+ struct aspeed_sdhci *aspeed_sdhci;
+ struct aspeed_sdc *aspeed_sdc;
+ u8 ctrl;
+
+ pltfm_priv = sdhci_priv(host);
+ aspeed_sdhci = sdhci_pltfm_priv(pltfm_priv);
+ aspeed_sdc = aspeed_sdhci->parent;
+
+ /* Set/clear 8-bit mode */
+ aspeed_sdc_bus_width(aspeed_sdc, aspeed_sdhci,
+ width == MMC_BUS_WIDTH_8);
+
+ /* Set/clear 1 or 4 bit mode */
+ ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
+ if (width == MMC_BUS_WIDTH_4)
+ ctrl |= SDHCI_CTRL_4BITBUS;
+ else
+ ctrl &= ~SDHCI_CTRL_4BITBUS;
+ sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
+}
+
+static const struct sdhci_ops aspeed_sdhci_ops = {
+ .set_clock = aspeed_sdhci_set_clock,
+ .get_max_clock = sdhci_pltfm_clk_get_max_clock,
+ .set_bus_width = aspeed_sdhci_set_bus_width,
+ .get_timeout_clock = sdhci_pltfm_clk_get_max_clock,
+ .reset = sdhci_reset,
+ .set_uhs_signaling = sdhci_set_uhs_signaling,
+};
+
+static const struct sdhci_pltfm_data aspeed_sdc_pdata = {
+ .ops = &aspeed_sdhci_ops,
+ .quirks = SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN,
+ .quirks2 = SDHCI_QUIRK2_CLOCK_DIV_ZERO_BROKEN,
+};
+
+static int aspeed_sdhci_probe(struct platform_device *pdev)
+{
+ struct sdhci_pltfm_host *pltfm_host;
+ struct aspeed_sdhci *dev;
+ struct sdhci_host *host;
+ u32 slot;
+ int ret;
+
+ host = sdhci_pltfm_init(pdev, &aspeed_sdc_pdata, sizeof(*dev));
+ if (IS_ERR(host))
+ return PTR_ERR(host);
+
+ pltfm_host = sdhci_priv(host);
+ dev = sdhci_pltfm_priv(pltfm_host);
+ dev->parent = dev_get_drvdata(pdev->dev.parent);
+
+ ret = of_property_read_u32(pdev->dev.of_node, "slot", &slot);
+ if (ret < 0)
+ return ret;
+ else if (slot > 2)
+ return -EINVAL;
+
+ dev->width_mask = !slot ? ASPEED_SDC_S0MMC8 : ASPEED_SDC_S1MMC8;
+
+ sdhci_get_of_property(pdev);
+
+ pltfm_host->clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(pltfm_host->clk))
+ return PTR_ERR(pltfm_host->clk);
+
+ ret = clk_prepare_enable(pltfm_host->clk);
+ if (ret) {
+ dev_err(&pdev->dev, "Unable to enable SDIO clock\n");
+ goto err_pltfm_free;
+ }
+
+ ret = mmc_of_parse(host->mmc);
+ if (ret)
+ goto err_sdhci_add;
+
+ ret = sdhci_add_host(host);
+ if (ret)
+ goto err_sdhci_add;
+
+ return 0;
+
+err_sdhci_add:
+ clk_disable_unprepare(pltfm_host->clk);
+err_pltfm_free:
+ sdhci_pltfm_free(pdev);
+ return ret;
+}
+
+static int aspeed_sdhci_remove(struct platform_device *pdev)
+{
+ struct sdhci_pltfm_host *pltfm_host;
+ struct sdhci_host *host;
+ int dead;
+
+ host = platform_get_drvdata(pdev);
+ pltfm_host = sdhci_priv(host);
+
+ dead = readl(host->ioaddr + SDHCI_INT_STATUS) == 0xffffffff;
+
+ sdhci_remove_host(host, dead);
+
+ clk_disable_unprepare(pltfm_host->clk);
+
+ sdhci_pltfm_free(pdev);
+
+ return 0;
+}
+
+static const struct of_device_id aspeed_sdhci_of_match[] = {
+ { .compatible = "aspeed,ast2400-sdhci", },
+ { .compatible = "aspeed,ast2500-sdhci", },
+ { }
+};
+
+MODULE_DEVICE_TABLE(of, aspeed_sdhci_of_match);
+
+static struct platform_driver aspeed_sdhci_driver = {
+ .driver = {
+ .name = "sdhci-aspeed",
+ .of_match_table = aspeed_sdhci_of_match,
+ },
+ .probe = aspeed_sdhci_probe,
+ .remove = aspeed_sdhci_remove,
+};
+
+module_platform_driver(aspeed_sdhci_driver);
+
+static int aspeed_sdc_probe(struct platform_device *pdev)
+
+{
+ struct device_node *parent, *child;
+ struct aspeed_sdc *sdc;
+ int ret;
+
+ sdc = devm_kzalloc(&pdev->dev, sizeof(*sdc), GFP_KERNEL);
+ if (!sdc)
+ return -ENOMEM;
+
+ spin_lock_init(&sdc->lock);
+
+ sdc->clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(sdc->clk))
+ return PTR_ERR(sdc->clk);
+
+ ret = clk_prepare_enable(sdc->clk);
+ if (ret) {
+ dev_err(&pdev->dev, "Unable to enable SDCLK\n");
+ return ret;
+ }
+
+ sdc->regs = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(sdc->regs)) {
+ ret = PTR_ERR(sdc->regs);
+ goto err_clk;
+ }
+
+ dev_set_drvdata(&pdev->dev, sdc);
+
+ parent = pdev->dev.of_node;
+ for_each_available_child_of_node(parent, child) {
+ struct platform_device *cpdev;
+
+ cpdev = of_platform_device_create(child, NULL, &pdev->dev);
+ if (IS_ERR(cpdev)) {
+ of_node_put(child);
+ ret = PTR_ERR(pdev);
+ goto err_clk;
+ }
+ }
+
+ return 0;
+
+err_clk:
+ clk_disable_unprepare(sdc->clk);
+ return ret;
+}
+
+static int aspeed_sdc_remove(struct platform_device *pdev)
+{
+ struct aspeed_sdc *sdc = dev_get_drvdata(&pdev->dev);
+
+ clk_disable_unprepare(sdc->clk);
+
+ return 0;
+}
+
+static const struct of_device_id aspeed_sdc_of_match[] = {
+ { .compatible = "aspeed,ast2400-sdc", .data = &aspeed_sdc_pdata },
+ { .compatible = "aspeed,ast2500-sdc", .data = &aspeed_sdc_pdata },
+ { }
+};
+
+MODULE_DEVICE_TABLE(of, aspeed_sdc_of_match);
+
+static struct platform_driver aspeed_sdc_driver = {
+ .driver = {
+ .name = "sdc-aspeed",
+ .pm = &sdhci_pltfm_pmops,
+ .of_match_table = aspeed_sdc_of_match,
+ },
+ .probe = aspeed_sdc_probe,
+ .remove = aspeed_sdc_remove,
+};
+
+module_platform_driver(aspeed_sdc_driver);
+
+MODULE_DESCRIPTION("Driver for the ASPEED SD/SDIO/SDHCI Controllers");
+MODULE_AUTHOR("Ryan Chen <[email protected]>");
+MODULE_AUTHOR("Andrew Jeffery <[email protected]>");
+MODULE_LICENSE("GPL v2");
--
2.20.1
On Wed, Jul 10, 2019 at 8:16 AM Andrew Jeffery <[email protected]> wrote:
>
> The ASPEED SD/SDIO/eMMC controller exposes two slots implementing the
> SDIO Host Specification v2.00, with 1 or 4 bit data buses, or an 8 bit
> data bus if only a single slot is enabled.
>
> Signed-off-by: Andrew Jeffery <[email protected]>
> ---
> .../bindings/mmc/sdhci-of-aspeed.yaml | 91 +++++++++++++++++++
aspeed,sdhci.yaml
> 1 file changed, 91 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mmc/sdhci-of-aspeed.yaml
>
> diff --git a/Documentation/devicetree/bindings/mmc/sdhci-of-aspeed.yaml b/Documentation/devicetree/bindings/mmc/sdhci-of-aspeed.yaml
> new file mode 100644
> index 000000000000..e98a2ac4d46d
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mmc/sdhci-of-aspeed.yaml
> @@ -0,0 +1,91 @@
> +# SPDX-License-Identifier: GPL-2.0-or-later
The preferred license is (GPL-2.0 OR BSD-2-Clause) if that is okay with you.
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/mmc/sdhci-of-aspeed.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: ASPEED SD/SDIO/eMMC Controller
> +
> +maintainers:
> + - Andrew Jeffery <[email protected]>
> + - Ryan Chen <[email protected]>
> +
> +description: |+
> + The ASPEED SD/SDIO/eMMC controller exposes two slots implementing the SDIO
> + Host Specification v2.00, with 1 or 4 bit data buses, or an 8 bit data bus if
> + only a single slot is enabled.
> +
> + The two slots are supported by a common configuration area. As the SDHCIs for
> + the slots are dependent on the common configuration area, they are described
> + as child nodes.
> +
> +properties:
> + compatible:
> + enum: [ aspeed,ast2400-sdc, aspeed,ast2500-sdc ]
> + reg:
> + description: Common configuration registers
This should have a 'maxItems: 1'. Same for the child reg.
> + ranges: true
> + clocks:
> + maxItems: 1
> + description: The SD/SDIO controller clock gate
> + sdhci:
This needs to be a pattern (under patternProperties) as these have
unit-addresses.
> + type: object
> + properties:
> + compatible:
> + allOf:
> + - enum: [ aspeed,ast2400-sdhci, aspeed,ast2500-sdhci ]
> + - const: sdhci
This condition can never be true. What you need is s/allOf/items/.
However, 'sdhci' is not really a useful compatible because every
implementation has quirks, so I'd drop it.
> + reg:
> + description: The SDHCI registers
> + clocks:
> + maxItems: 1
> + description: The SD bus clock
> + slot:
> + allOf:
> + - $ref: /schemas/types.yaml#/definitions/uint32
> + - enum: [0, 1]
Is this really needed? Offset 0x100 is slot 0 and offset 0x200 is slot
1. Does that ever change?
> + interrupts:
> + maxItems: 1
> + description: The SD interrupt shared between both slots
> + required:
> + - compatible
> + - reg
> + - clocks
> + - slot
> + - interrupts
> +
> +required:
> + - compatible
> + - reg
> + - ranges
> + - clocks
#address-cells and #size-cells are required too.
You should also add 'additionalProperties: false' here so other random
properties can't be present.
> +
> +examples:
> + - |
> + #include <dt-bindings/clock/aspeed-clock.h>
> + sdc@1e740000 {
> + compatible = "aspeed,ast2500-sdc";
> + reg = <0x1e740000 0x100>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
It's preferred to limit the range here and then the child addresses
are 0x100 and 0x200.
> + clocks = <&syscon ASPEED_CLK_GATE_SDCLK>;
> +
> + sdhci0: sdhci@1e740100 {
> + compatible = "aspeed,ast2500-sdhci", "sdhci";
> + reg = <0x1e740100 0x100>;
> + slot = <0>;
> + interrupts = <26>;
> + sdhci,auto-cmd12;
> + clocks = <&syscon ASPEED_CLK_SDIO>;
> + };
> +
> + sdhci1: sdhci@1e740200 {
> + compatible = "aspeed,ast2500-sdhci", "sdhci";
> + reg = <0x1e740200 0x100>;
> + slot = <1>;
> + interrupts = <26>;
> + sdhci,auto-cmd12;
> + clocks = <&syscon ASPEED_CLK_SDIO>;
> + };
> + };
> --
> 2.20.1
>
On Thu, 11 Jul 2019, at 01:20, Rob Herring wrote:
> On Wed, Jul 10, 2019 at 8:16 AM Andrew Jeffery <[email protected]> wrote:
> >
> > The ASPEED SD/SDIO/eMMC controller exposes two slots implementing the
> > SDIO Host Specification v2.00, with 1 or 4 bit data buses, or an 8 bit
> > data bus if only a single slot is enabled.
> >
> > Signed-off-by: Andrew Jeffery <[email protected]>
> > ---
> > .../bindings/mmc/sdhci-of-aspeed.yaml | 91 +++++++++++++++++++
>
> aspeed,sdhci.yaml
Ack. Previously I had separate documents for different compatibles, wasn't sure
how to tackle name one document covering multiple compatibles.
>
> > 1 file changed, 91 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/mmc/sdhci-of-aspeed.yaml
> >
> > diff --git a/Documentation/devicetree/bindings/mmc/sdhci-of-aspeed.yaml b/Documentation/devicetree/bindings/mmc/sdhci-of-aspeed.yaml
> > new file mode 100644
> > index 000000000000..e98a2ac4d46d
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/mmc/sdhci-of-aspeed.yaml
> > @@ -0,0 +1,91 @@
> > +# SPDX-License-Identifier: GPL-2.0-or-later
>
> The preferred license is (GPL-2.0 OR BSD-2-Clause) if that is okay with you.
I should poke people internally again, I had asked, just haven't got a clear
answer. What was the justification for the preference (just so I can pass that
on)?
>
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/mmc/sdhci-of-aspeed.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: ASPEED SD/SDIO/eMMC Controller
> > +
> > +maintainers:
> > + - Andrew Jeffery <[email protected]>
> > + - Ryan Chen <[email protected]>
> > +
> > +description: |+
> > + The ASPEED SD/SDIO/eMMC controller exposes two slots implementing the SDIO
> > + Host Specification v2.00, with 1 or 4 bit data buses, or an 8 bit data bus if
> > + only a single slot is enabled.
> > +
> > + The two slots are supported by a common configuration area. As the SDHCIs for
> > + the slots are dependent on the common configuration area, they are described
> > + as child nodes.
> > +
> > +properties:
> > + compatible:
> > + enum: [ aspeed,ast2400-sdc, aspeed,ast2500-sdc ]
> > + reg:
> > + description: Common configuration registers
>
> This should have a 'maxItems: 1'. Same for the child reg.
Ack.
>
> > + ranges: true
> > + clocks:
> > + maxItems: 1
> > + description: The SD/SDIO controller clock gate
> > + sdhci:
>
> This needs to be a pattern (under patternProperties) as these have
> unit-addresses.
Ah, I didn't think about that.
>
> > + type: object
> > + properties:
> > + compatible:
> > + allOf:
> > + - enum: [ aspeed,ast2400-sdhci, aspeed,ast2500-sdhci ]
> > + - const: sdhci
>
> This condition can never be true. What you need is s/allOf/items/.
> However, 'sdhci' is not really a useful compatible because every
> implementation has quirks, so I'd drop it.
Yeah, I was tossing up whether to include "sdhci". I'll drop it as you
suggest.
Pity the shorthand doesn't work how I expected. Might explain
some of the behaviour I was seeing with the bindings make targets
though.
>
> > + reg:
> > + description: The SDHCI registers
> > + clocks:
> > + maxItems: 1
> > + description: The SD bus clock
> > + slot:
> > + allOf:
> > + - $ref: /schemas/types.yaml#/definitions/uint32
> > + - enum: [0, 1]
>
> Is this really needed? Offset 0x100 is slot 0 and offset 0x200 is slot
> 1. Does that ever change?
It doesn't in the SoCs at hand, but the downstream impact (driver
implementation) is that you need to derive the slot index from the
address and I was trying to avoid that. The slot index influences
some bit index calculations.
>
> > + interrupts:
> > + maxItems: 1
> > + description: The SD interrupt shared between both slots
> > + required:
> > + - compatible
> > + - reg
> > + - clocks
> > + - slot
> > + - interrupts
> > +
> > +required:
> > + - compatible
> > + - reg
> > + - ranges
> > + - clocks
>
> #address-cells and #size-cells are required too.
Ack.
>
> You should also add 'additionalProperties: false' here so other random
> properties can't be present.
Ah yes. Will fix.
>
> > +
> > +examples:
> > + - |
> > + #include <dt-bindings/clock/aspeed-clock.h>
> > + sdc@1e740000 {
> > + compatible = "aspeed,ast2500-sdc";
> > + reg = <0x1e740000 0x100>;
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + ranges;
>
> It's preferred to limit the range here and then the child addresses
> are 0x100 and 0x200.
Okay. Was just trying to dodge mental arithmetic where I could, but
if that's the preference then I'll fix it up.
Thanks for the review!
Andrew
>
> > + clocks = <&syscon ASPEED_CLK_GATE_SDCLK>;
> > +
> > + sdhci0: sdhci@1e740100 {
> > + compatible = "aspeed,ast2500-sdhci", "sdhci";
> > + reg = <0x1e740100 0x100>;
> > + slot = <0>;
> > + interrupts = <26>;
> > + sdhci,auto-cmd12;
> > + clocks = <&syscon ASPEED_CLK_SDIO>;
> > + };
> > +
> > + sdhci1: sdhci@1e740200 {
> > + compatible = "aspeed,ast2500-sdhci", "sdhci";
> > + reg = <0x1e740200 0x100>;
> > + slot = <1>;
> > + interrupts = <26>;
> > + sdhci,auto-cmd12;
> > + clocks = <&syscon ASPEED_CLK_SDIO>;
> > + };
> > + };
> > --
> > 2.20.1
> >
>
On Wed, Jul 10, 2019 at 6:56 PM Andrew Jeffery <[email protected]> wrote:
>
>
>
> On Thu, 11 Jul 2019, at 01:20, Rob Herring wrote:
> > On Wed, Jul 10, 2019 at 8:16 AM Andrew Jeffery <[email protected]> wrote:
> > >
> > > The ASPEED SD/SDIO/eMMC controller exposes two slots implementing the
> > > SDIO Host Specification v2.00, with 1 or 4 bit data buses, or an 8 bit
> > > data bus if only a single slot is enabled.
> > >
> > > Signed-off-by: Andrew Jeffery <[email protected]>
> > > ---
> > > .../bindings/mmc/sdhci-of-aspeed.yaml | 91 +++++++++++++++++++
> >
> > aspeed,sdhci.yaml
>
> Ack. Previously I had separate documents for different compatibles, wasn't sure
> how to tackle name one document covering multiple compatibles.
>
> >
> > > 1 file changed, 91 insertions(+)
> > > create mode 100644 Documentation/devicetree/bindings/mmc/sdhci-of-aspeed.yaml
> > >
> > > diff --git a/Documentation/devicetree/bindings/mmc/sdhci-of-aspeed.yaml b/Documentation/devicetree/bindings/mmc/sdhci-of-aspeed.yaml
> > > new file mode 100644
> > > index 000000000000..e98a2ac4d46d
> > > --- /dev/null
> > > +++ b/Documentation/devicetree/bindings/mmc/sdhci-of-aspeed.yaml
> > > @@ -0,0 +1,91 @@
> > > +# SPDX-License-Identifier: GPL-2.0-or-later
> >
> > The preferred license is (GPL-2.0 OR BSD-2-Clause) if that is okay with you.
>
> I should poke people internally again, I had asked, just haven't got a clear
> answer. What was the justification for the preference (just so I can pass that
> on)?
To use schema in non-GPL projects. *BSD, Zephyr, etc.
Rob