This patch series adds trigger buffer support with data ready interrupt,
separate channel for step counter, an event for step change interrupt,
activity recognition and activity/inactivity event support.
changes since v3
1. Removed all the unnecessary mutex locking for regmap.
2. Corrected the mutex locking and unlocking for device private data
members.
3. Mutex locking and unlocking is used to protect the device private
structure members.
4. Using DMA safe buffer for regmap_bulk_write() and regmap_bulk_read().
1/9: Fixed the comment.
3/9: Added () for the function name in the comment.
4/9: Handling error cases with goto in bma400_trigger_handler().
Mutex locking and unlocking is used to protect the data->buffer.
Using DMA safe buffer for regmap_bulk_read().
Mutex locking and unlocking is used to protect the data->status in
bma400_interrupt.
5/9: Using DMA safe buffers to read steps value by allocating memory internally.
Using DMA safe buffers for regmap_bulk_write().
Removed the lock for regmap().
6/9: Removed the duplication of code for enabling step, added function to handle
the step enable.
7/9: Removed the lock for regmap().
Mutex locking and unlocking is used to protect the data members.
8/9: Removed the lock for regmap().
9/9. Added __be16 duration in struct bma400_data.
Fixed the warning - impossible condition '(reg < 0) => (0-255 < 0)'
Fixed error: call to __compiletime_assert_272
Reported-by: kernel test robot <[email protected]>
Reported-by: Dan Carpenter <[email protected]>
changes since v2
1. Reordering of header includes in the separate patch.
2. Matching the IIO syntax for multiline comment.
3. Following the preference in the interrupt handler for returning.
4. Add support for activity recognition.
5. Add support for debugfs to access registers from userspace.
6. Add support for activity and inactivity events
changes since v1
1. Added comment section that describes the math for scale calculation.
2. Added separate devm_add_action_or_reset() calls to disable regulator
and to put the sensor in power down mode.
3. Remove the err_reg_disable and out, goto labels and returning directly
if error occurs.
4. Added mutex calls while putting sensor in power down.
5. Added ___cacheline_aligned for device data.
6. Ordering the header includes.
7. Handling erroneous and spurious interrupts in the interrupt handler
by returning IRQ_NONE.
8. Using dev_err_probe() instead of dev_err().
9. Configured the interrupt to open drain.
10. Using le16_to_cpu() to fix the sparse warning.
11. Checking the step change event is enabled or not.
12. Enabling the step change event will also enable the step channel.
13. Using FIELD_GET() instead of bitwise operation.
14. Removal of dead code in the _event_config().
Jagath Jog J (9):
iio: accel: bma400: Fix the scale min and max macro values
iio: accel: bma400: Reordering of header files
iio: accel: bma400: conversion to device-managed function
iio: accel: bma400: Add triggered buffer support
iio: accel: bma400: Add separate channel for step counter
iio: accel: bma400: Add step change event
iio: accel: bma400: Add activity recognition support
iio: accel: bma400: Add debugfs register access support
iio: accel: bma400: Add support for activity and inactivity events
drivers/iio/accel/Kconfig | 2 +
drivers/iio/accel/bma400.h | 50 ++-
drivers/iio/accel/bma400_core.c | 694 +++++++++++++++++++++++++++++---
drivers/iio/accel/bma400_i2c.c | 10 +-
drivers/iio/accel/bma400_spi.c | 8 +-
5 files changed, 697 insertions(+), 67 deletions(-)
--
2.17.1
On Wed, Apr 20, 2022 at 11:11 PM Jagath Jog J <[email protected]> wrote:
>
> This patch series adds trigger buffer support with data ready interrupt,
> separate channel for step counter, an event for step change interrupt,
> activity recognition and activity/inactivity event support.
You forgot to add tags from the previous round of review, please be
respectful to reviewers.
> changes since v3
> 1. Removed all the unnecessary mutex locking for regmap.
> 2. Corrected the mutex locking and unlocking for device private data
> members.
> 3. Mutex locking and unlocking is used to protect the device private
> structure members.
> 4. Using DMA safe buffer for regmap_bulk_write() and regmap_bulk_read().
>
> 1/9: Fixed the comment.
>
> 3/9: Added () for the function name in the comment.
>
> 4/9: Handling error cases with goto in bma400_trigger_handler().
> Mutex locking and unlocking is used to protect the data->buffer.
> Using DMA safe buffer for regmap_bulk_read().
> Mutex locking and unlocking is used to protect the data->status in
> bma400_interrupt.
>
> 5/9: Using DMA safe buffers to read steps value by allocating memory internally.
> Using DMA safe buffers for regmap_bulk_write().
> Removed the lock for regmap().
>
> 6/9: Removed the duplication of code for enabling step, added function to handle
> the step enable.
>
> 7/9: Removed the lock for regmap().
> Mutex locking and unlocking is used to protect the data members.
>
> 8/9: Removed the lock for regmap().
>
> 9/9. Added __be16 duration in struct bma400_data.
> Fixed the warning - impossible condition '(reg < 0) => (0-255 < 0)'
> Fixed error: call to __compiletime_assert_272
> Reported-by: kernel test robot <[email protected]>
> Reported-by: Dan Carpenter <[email protected]>
>
> changes since v2
> 1. Reordering of header includes in the separate patch.
> 2. Matching the IIO syntax for multiline comment.
> 3. Following the preference in the interrupt handler for returning.
> 4. Add support for activity recognition.
> 5. Add support for debugfs to access registers from userspace.
> 6. Add support for activity and inactivity events
>
> changes since v1
> 1. Added comment section that describes the math for scale calculation.
> 2. Added separate devm_add_action_or_reset() calls to disable regulator
> and to put the sensor in power down mode.
> 3. Remove the err_reg_disable and out, goto labels and returning directly
> if error occurs.
> 4. Added mutex calls while putting sensor in power down.
> 5. Added ___cacheline_aligned for device data.
> 6. Ordering the header includes.
> 7. Handling erroneous and spurious interrupts in the interrupt handler
> by returning IRQ_NONE.
> 8. Using dev_err_probe() instead of dev_err().
> 9. Configured the interrupt to open drain.
> 10. Using le16_to_cpu() to fix the sparse warning.
> 11. Checking the step change event is enabled or not.
> 12. Enabling the step change event will also enable the step channel.
> 13. Using FIELD_GET() instead of bitwise operation.
> 14. Removal of dead code in the _event_config().
>
> Jagath Jog J (9):
> iio: accel: bma400: Fix the scale min and max macro values
> iio: accel: bma400: Reordering of header files
> iio: accel: bma400: conversion to device-managed function
> iio: accel: bma400: Add triggered buffer support
> iio: accel: bma400: Add separate channel for step counter
> iio: accel: bma400: Add step change event
> iio: accel: bma400: Add activity recognition support
> iio: accel: bma400: Add debugfs register access support
> iio: accel: bma400: Add support for activity and inactivity events
>
> drivers/iio/accel/Kconfig | 2 +
> drivers/iio/accel/bma400.h | 50 ++-
> drivers/iio/accel/bma400_core.c | 694 +++++++++++++++++++++++++++++---
> drivers/iio/accel/bma400_i2c.c | 10 +-
> drivers/iio/accel/bma400_spi.c | 8 +-
> 5 files changed, 697 insertions(+), 67 deletions(-)
>
> --
> 2.17.1
>
--
With Best Regards,
Andy Shevchenko
Hello Andy,
On Tue, Apr 26, 2022 at 4:35 PM Andy Shevchenko
<[email protected]> wrote:
>
> On Tue, Apr 26, 2022 at 1:04 PM Andy Shevchenko
> <[email protected]> wrote:
> >
> > On Wed, Apr 20, 2022 at 11:11 PM Jagath Jog J <[email protected]> wrote:
> > >
> > > This patch series adds trigger buffer support with data ready interrupt,
> > > separate channel for step counter, an event for step change interrupt,
> > > activity recognition and activity/inactivity event support.
> >
> > You forgot to add tags from the previous round of review, please be
> > respectful to reviewers.
>
> That said, send a new version with properly added tags for what it was given.
I have followed your comments from previous series and added the 'Fixes' tag for
patch 1, also added your 'Reviewed-by' tag for patch number 2 and 3 for which
you have given previously.
>
> --
> With Best Regards,
> Andy Shevchenko
On Tue, Apr 26, 2022 at 1:04 PM Andy Shevchenko
<[email protected]> wrote:
>
> On Wed, Apr 20, 2022 at 11:11 PM Jagath Jog J <[email protected]> wrote:
> >
> > This patch series adds trigger buffer support with data ready interrupt,
> > separate channel for step counter, an event for step change interrupt,
> > activity recognition and activity/inactivity event support.
>
> You forgot to add tags from the previous round of review, please be
> respectful to reviewers.
That said, send a new version with properly added tags for what it was given.
--
With Best Regards,
Andy Shevchenko
On Thu, 21 Apr 2022 02:40:56 +0530
Jagath Jog J <[email protected]> wrote:
> This patch series adds trigger buffer support with data ready interrupt,
> separate channel for step counter, an event for step change interrupt,
> activity recognition and activity/inactivity event support.
Hi Jagath,
This is coming together nicely. I'm fine with all the patches
I haven't sent specific replies for.
Thanks,
Jonathan
>
> changes since v3
> 1. Removed all the unnecessary mutex locking for regmap.
> 2. Corrected the mutex locking and unlocking for device private data
> members.
> 3. Mutex locking and unlocking is used to protect the device private
> structure members.
> 4. Using DMA safe buffer for regmap_bulk_write() and regmap_bulk_read().
>
> 1/9: Fixed the comment.
>
> 3/9: Added () for the function name in the comment.
>
> 4/9: Handling error cases with goto in bma400_trigger_handler().
> Mutex locking and unlocking is used to protect the data->buffer.
> Using DMA safe buffer for regmap_bulk_read().
> Mutex locking and unlocking is used to protect the data->status in
> bma400_interrupt.
>
> 5/9: Using DMA safe buffers to read steps value by allocating memory internally.
> Using DMA safe buffers for regmap_bulk_write().
> Removed the lock for regmap().
>
> 6/9: Removed the duplication of code for enabling step, added function to handle
> the step enable.
>
> 7/9: Removed the lock for regmap().
> Mutex locking and unlocking is used to protect the data members.
>
> 8/9: Removed the lock for regmap().
>
> 9/9. Added __be16 duration in struct bma400_data.
> Fixed the warning - impossible condition '(reg < 0) => (0-255 < 0)'
> Fixed error: call to __compiletime_assert_272
> Reported-by: kernel test robot <[email protected]>
> Reported-by: Dan Carpenter <[email protected]>
>
> changes since v2
> 1. Reordering of header includes in the separate patch.
> 2. Matching the IIO syntax for multiline comment.
> 3. Following the preference in the interrupt handler for returning.
> 4. Add support for activity recognition.
> 5. Add support for debugfs to access registers from userspace.
> 6. Add support for activity and inactivity events
>
> changes since v1
> 1. Added comment section that describes the math for scale calculation.
> 2. Added separate devm_add_action_or_reset() calls to disable regulator
> and to put the sensor in power down mode.
> 3. Remove the err_reg_disable and out, goto labels and returning directly
> if error occurs.
> 4. Added mutex calls while putting sensor in power down.
> 5. Added ___cacheline_aligned for device data.
> 6. Ordering the header includes.
> 7. Handling erroneous and spurious interrupts in the interrupt handler
> by returning IRQ_NONE.
> 8. Using dev_err_probe() instead of dev_err().
> 9. Configured the interrupt to open drain.
> 10. Using le16_to_cpu() to fix the sparse warning.
> 11. Checking the step change event is enabled or not.
> 12. Enabling the step change event will also enable the step channel.
> 13. Using FIELD_GET() instead of bitwise operation.
> 14. Removal of dead code in the _event_config().
>
> Jagath Jog J (9):
> iio: accel: bma400: Fix the scale min and max macro values
> iio: accel: bma400: Reordering of header files
> iio: accel: bma400: conversion to device-managed function
> iio: accel: bma400: Add triggered buffer support
> iio: accel: bma400: Add separate channel for step counter
> iio: accel: bma400: Add step change event
> iio: accel: bma400: Add activity recognition support
> iio: accel: bma400: Add debugfs register access support
> iio: accel: bma400: Add support for activity and inactivity events
>
> drivers/iio/accel/Kconfig | 2 +
> drivers/iio/accel/bma400.h | 50 ++-
> drivers/iio/accel/bma400_core.c | 694 +++++++++++++++++++++++++++++---
> drivers/iio/accel/bma400_i2c.c | 10 +-
> drivers/iio/accel/bma400_spi.c | 8 +-
> 5 files changed, 697 insertions(+), 67 deletions(-)
>