On Wed, 5 Aug 2020 at 16:21, Amit Pundir <[email protected]> wrote:
>
> Add initial dts support for Xiaomi Poco F1 (Beryllium).
>
> This initial support is based on upstream Dragonboard 845c
> (sdm845) device. With this dts, Beryllium boots AOSP up to
> ADB shell over USB-C.
>
> Supported functionality includes UFS, USB-C (peripheral),
> microSD card and Vol+/Vol-/power keys. Bluetooth should work
> too but couldn't be verified from adb command line, it is
> verified when enabled from UI with few WIP display patches.
>
> Just like initial db845c support, initializing the SMMU is
> clearing the mapping used for the splash screen framebuffer,
> which causes the device to hang during boot and recovery
> needs a hard power reset. This can be worked around using:
>
> fastboot oem select-display-panel none
>
> To switch ON the display back run:
>
> fastboot oem select-display-panel
>
> But this only works on Beryllium devices running bootloader
> version BOOT.XF.2.0-00369-SDM845LZB-1 that shipped with
> Android-9 based release. Newer bootloader version do not
> support switching OFF the display panel at all. So we need
> a few additional smmu patches (under review) from here to
> boot to shell:
> https://github.com/pundiramit/linux/commits/beryllium-mainline
>
> Signed-off-by: Amit Pundir <[email protected]>
> ---
> v4: Added more downstream reserved memory regions. It probably
> need more work, but for now I see adsp/cdsp/wlan remoteprocs
> powering up properly. Also removed the regulator nodes not
> required for the device, as suggested by Bjorn.
Forgot to mention that I added couple of clocks to protected clocks in v4,
which need for display to work.
> v3: Added a reserved-memory region from downstream kernel to fix
> a boot regression with recent dma-pool changes in v5.8-rc6.
> v2: Updated machine compatible string for seemingly inevitable
> future quirks.
>
> arch/arm64/boot/dts/qcom/Makefile | 1 +
> arch/arm64/boot/dts/qcom/sdm845-beryllium.dts | 383 ++++++++++++++++++++++++++
> 2 files changed, 384 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/sdm845-beryllium.dts
>
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 0f2c33d611df..3ef1b48bc0cb 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -21,6 +21,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r1.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r2.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r3.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sdm845-db845c.dtb
> +dtb-$(CONFIG_ARCH_QCOM) += sdm845-beryllium.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sdm845-mtp.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sdm850-lenovo-yoga-c630.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sm8150-mtp.dtb
> diff --git a/arch/arm64/boot/dts/qcom/sdm845-beryllium.dts b/arch/arm64/boot/dts/qcom/sdm845-beryllium.dts
> new file mode 100644
> index 000000000000..0f9f61bf9fa4
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/sdm845-beryllium.dts
> @@ -0,0 +1,383 @@
> +// SPDX-License-Identifier: GPL-2.0
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
> +#include "sdm845.dtsi"
> +#include "pm8998.dtsi"
> +#include "pmi8998.dtsi"
> +
> +/ {
> + model = "Xiaomi Technologies Inc. Beryllium";
> + compatible = "xiaomi,beryllium", "qcom,sdm845";
> +
> + /* required for bootloader to select correct board */
> + qcom,board-id = <69 0>;
> + qcom,msm-id = <321 0x20001>;
> +
> + aliases {
> + hsuart0 = &uart6;
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> + autorepeat;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&vol_up_pin_a>;
> +
> + vol-up {
> + label = "Volume Up";
> + linux,code = <KEY_VOLUMEUP>;
> + gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
> + };
> + };
> +
> + vreg_s4a_1p8: vreg-s4a-1p8 {
> + compatible = "regulator-fixed";
> + regulator-name = "vreg_s4a_1p8";
> +
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +};
> +
> +&adsp_pas {
> + status = "okay";
> + firmware-name = "qcom/sdm845/adsp.mdt";
> +};
> +
> +&apps_rsc {
> + pm8998-rpmh-regulators {
> + compatible = "qcom,pm8998-rpmh-regulators";
> + qcom,pmic-id = "a";
> +
> + vreg_l1a_0p875: ldo1 {
> + regulator-min-microvolt = <880000>;
> + regulator-max-microvolt = <880000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l5a_0p8: ldo5 {
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l7a_1p8: ldo7 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l12a_1p8: ldo12 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l13a_2p95: ldo13 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <2960000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l17a_1p3: ldo17 {
> + regulator-min-microvolt = <1304000>;
> + regulator-max-microvolt = <1304000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l20a_2p95: ldo20 {
> + regulator-min-microvolt = <2960000>;
> + regulator-max-microvolt = <2968000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l21a_2p95: ldo21 {
> + regulator-min-microvolt = <2960000>;
> + regulator-max-microvolt = <2968000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l24a_3p075: ldo24 {
> + regulator-min-microvolt = <3088000>;
> + regulator-max-microvolt = <3088000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l25a_3p3: ldo25 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3312000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l26a_1p2: ldo26 {
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> + };
> +};
> +
> +&cdsp_pas {
> + status = "okay";
> + firmware-name = "qcom/sdm845/cdsp.mdt";
> +};
> +
> +&gcc {
> + protected-clocks = <GCC_QSPI_CORE_CLK>,
> + <GCC_QSPI_CORE_CLK_SRC>,
> + <GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
> + <GCC_LPASS_Q6_AXI_CLK>,
> + <GCC_LPASS_SWAY_CLK>;
> +};
> +
> +&gpu {
> + zap-shader {
> + memory-region = <&gpu_mem>;
> + firmware-name = "qcom/sdm845/a630_zap.mbn";
> + };
> +};
> +
> +/* Reserved memory changes from downstream */
> +/delete-node/ &adsp_mem;
> +/delete-node/ &wlan_msa_mem;
> +/delete-node/ &mpss_region;
> +/delete-node/ &venus_mem;
> +/delete-node/ &cdsp_mem;
> +/delete-node/ &mba_region;
> +/delete-node/ &slpi_mem;
> +/delete-node/ &spss_mem;
> +/delete-node/ &rmtfs_mem;
> +/ {
> + reserved-memory {
> + // This removed_region is needed to boot the device
> + // TODO: Find out the user of this reserved memory
> + removed_region: memory@88f00000 {
> + reg = <0 0x88f00000 0 0x1a00000>;
> + no-map;
> + };
> +
> + adsp_mem: memory@8c500000 {
> + reg = <0 0x8c500000 0 0x1e00000>;
> + no-map;
> + };
> +
> + wlan_msa_mem: memory@8e300000 {
> + reg = <0 0x8e300000 0 0x100000>;
> + no-map;
> + };
> +
> + mpss_region: memory@8e400000 {
> + reg = <0 0x8e400000 0 0x7800000>;
> + no-map;
> + };
> +
> + venus_mem: memory@95c00000 {
> + reg = <0 0x95c00000 0 0x500000>;
> + no-map;
> + };
> +
> + cdsp_mem: memory@96100000 {
> + reg = <0 0x96100000 0 0x800000>;
> + no-map;
> + };
> +
> + mba_region: memory@96900000 {
> + reg = <0 0x96900000 0 0x200000>;
> + no-map;
> + };
> +
> + slpi_mem: memory@96b00000 {
> + reg = <0 0x96b00000 0 0x1400000>;
> + no-map;
> + };
> +
> + spss_mem: memory@97f00000 {
> + reg = <0 0x97f00000 0 0x100000>;
> + no-map;
> + };
> +
> + rmtfs_mem: memory@f6301000 {
> + compatible = "qcom,rmtfs-mem";
> + reg = <0 0xf6301000 0 0x200000>;
> + no-map;
> +
> + qcom,client-id = <1>;
> + qcom,vmid = <15>;
> + };
> + };
> +};
> +
> +&mss_pil {
> + status = "okay";
> + firmware-name = "qcom/sdm845/mba.mbn", "qcom/sdm845/modem.mdt";
> +};
> +
> +&pm8998_gpio {
> + vol_up_pin_a: vol-up-active {
> + pins = "gpio6";
> + function = "normal";
> + input-enable;
> + bias-pull-up;
> + qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
> + };
> +};
> +
> +&pm8998_pon {
> + resin {
> + compatible = "qcom,pm8941-resin";
> + interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
> + debounce = <15625>;
> + bias-pull-up;
> + linux,code = <KEY_VOLUMEDOWN>;
> + };
> +};
> +
> +&qupv3_id_0 {
> + status = "okay";
> +};
> +
> +&sdhc_2 {
> + status = "okay";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdc2_default_state &sdc2_card_det_n>;
> +
> + vmmc-supply = <&vreg_l21a_2p95>;
> + vqmmc-supply = <&vreg_l13a_2p95>;
> +
> + bus-width = <4>;
> + cd-gpios = <&tlmm 126 GPIO_ACTIVE_HIGH>;
> +};
> +
> +&tlmm {
> + gpio-reserved-ranges = <0 4>, <81 4>;
> +
> + sdc2_default_state: sdc2-default {
> + clk {
> + pins = "sdc2_clk";
> + bias-disable;
> +
> + /*
> + * It seems that mmc_test reports errors if drive
> + * strength is not 16 on clk, cmd, and data pins.
> + */
> + drive-strength = <16>;
> + };
> +
> + cmd {
> + pins = "sdc2_cmd";
> + bias-pull-up;
> + drive-strength = <10>;
> + };
> +
> + data {
> + pins = "sdc2_data";
> + bias-pull-up;
> + drive-strength = <10>;
> + };
> + };
> +
> + sdc2_card_det_n: sd-card-det-n {
> + pins = "gpio126";
> + function = "gpio";
> + bias-pull-up;
> + };
> +};
> +
> +&uart6 {
> + status = "okay";
> +
> + bluetooth {
> + compatible = "qcom,wcn3990-bt";
> +
> + vddio-supply = <&vreg_s4a_1p8>;
> + vddxo-supply = <&vreg_l7a_1p8>;
> + vddrf-supply = <&vreg_l17a_1p3>;
> + vddch0-supply = <&vreg_l25a_3p3>;
> + max-speed = <3200000>;
> + };
> +};
> +
> +&usb_1 {
> + status = "okay";
> +};
> +
> +&usb_1_dwc3 {
> + dr_mode = "peripheral";
> +};
> +
> +&usb_1_hsphy {
> + status = "okay";
> +
> + vdd-supply = <&vreg_l1a_0p875>;
> + vdda-pll-supply = <&vreg_l12a_1p8>;
> + vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
> +
> + qcom,imp-res-offset-value = <8>;
> + qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
> + qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
> + qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
> +};
> +
> +&usb_1_qmpphy {
> + status = "okay";
> +
> + vdda-phy-supply = <&vreg_l26a_1p2>;
> + vdda-pll-supply = <&vreg_l1a_0p875>;
> +};
> +
> +&ufs_mem_hc {
> + status = "okay";
> +
> + reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>;
> +
> + vcc-supply = <&vreg_l20a_2p95>;
> + vcc-max-microamp = <800000>;
> +};
> +
> +&ufs_mem_phy {
> + status = "okay";
> +
> + vdda-phy-supply = <&vreg_l1a_0p875>;
> + vdda-pll-supply = <&vreg_l26a_1p2>;
> +};
> +
> +&wifi {
> + status = "okay";
> +
> + vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
> + vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
> + vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
> + vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
> +};
> +
> +/* PINCTRL - additions to nodes defined in sdm845.dtsi */
> +
> +&qup_uart6_default {
> + pinmux {
> + pins = "gpio45", "gpio46", "gpio47", "gpio48";
> + function = "qup6";
> + };
> +
> + cts {
> + pins = "gpio45";
> + bias-disable;
> + };
> +
> + rts-tx {
> + pins = "gpio46", "gpio47";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + rx {
> + pins = "gpio48";
> + bias-pull-up;
> + };
> +};
> --
> 2.7.4
>
Subject: Re: [PATCH v4] arm64: dts: qcom: Add support for Xiaomi Poco F1 (Beryllium)
>// This removed_region is needed to boot the device
> // TODO: Find out the user of this reserved memory
> removed_region: memory@88f00000 {
This region seems to belong to the Trust Zone. When Linux tries to access it, TZ bites and shuts the device down.
Konrad
On Fri, 7 Aug 2020 at 04:02, Konrad Dybcio <[email protected]> wrote:
>
> Subject: Re: [PATCH v4] arm64: dts: qcom: Add support for Xiaomi Poco F1 (Beryllium)
>
> >// This removed_region is needed to boot the device
> > // TODO: Find out the user of this reserved memory
> > removed_region: memory@88f00000 {
>
> This region seems to belong to the Trust Zone. When Linux tries to access it, TZ bites and shuts the device down.
That is totally possible. Plus it falls right in between TZ and QSEE
reserved-memory regions. However, I do not find any credible source
of information which can confirm this. So I'm hesitant to update the
TODO item in the above comment.
>
> Konrad
On Thu 06 Aug 15:31 PDT 2020, Konrad Dybcio wrote:
> Subject: Re: [PATCH v4] arm64: dts: qcom: Add support for Xiaomi Poco F1 (Beryllium)
>
> >// This removed_region is needed to boot the device
> > // TODO: Find out the user of this reserved memory
> > removed_region: memory@88f00000 {
>
> This region seems to belong to the Trust Zone. When Linux tries to access it, TZ bites and shuts the device down.
>
This is in line with what the documentation indicates and then it would
be better to just bump &tz_mem to a size of 0x4900000.
Regards,
Bjorn
On Thu, 13 Aug 2020 at 12:38, Bjorn Andersson
<[email protected]> wrote:
>
> On Thu 06 Aug 15:31 PDT 2020, Konrad Dybcio wrote:
>
> > Subject: Re: [PATCH v4] arm64: dts: qcom: Add support for Xiaomi Poco F1 (Beryllium)
> >
> > >// This removed_region is needed to boot the device
> > > // TODO: Find out the user of this reserved memory
> > > removed_region: memory@88f00000 {
> >
> > This region seems to belong to the Trust Zone. When Linux tries to access it, TZ bites and shuts the device down.
> >
>
> This is in line with what the documentation indicates and then it would
> be better to just bump &tz_mem to a size of 0x4900000.
Hi, so just to be sure that I got this right, you want me to extend
&tz_mem to the size of 0x4900000 from the default size of 0x2D00000 by
including this downstream &removed_region (of size 0x1A00000) +
previously unreserved downstream memory region (of size 0x200000), to
align with the starting address of &qseecom_mem?
I just gave this &tz_mem change a spin and I do not see any obvious
regression in my limited smoke testing (Boots AOSP to UI with
v5.9-rc1. Touch/BT/WiFi works) so far, with 20+ out-of-tree patches.
Regards,
Amit Pundir
>
> Regards,
> Bjorn
On Mon 17 Aug 17:12 UTC 2020, Amit Pundir wrote:
> On Thu, 13 Aug 2020 at 12:38, Bjorn Andersson
> <[email protected]> wrote:
> >
> > On Thu 06 Aug 15:31 PDT 2020, Konrad Dybcio wrote:
> >
> > > Subject: Re: [PATCH v4] arm64: dts: qcom: Add support for Xiaomi Poco F1 (Beryllium)
> > >
> > > >// This removed_region is needed to boot the device
> > > > // TODO: Find out the user of this reserved memory
> > > > removed_region: memory@88f00000 {
> > >
> > > This region seems to belong to the Trust Zone. When Linux tries to access it, TZ bites and shuts the device down.
> > >
> >
> > This is in line with what the documentation indicates and then it would
> > be better to just bump &tz_mem to a size of 0x4900000.
>
> Hi, so just to be sure that I got this right, you want me to extend
> &tz_mem to the size of 0x4900000 from the default size of 0x2D00000 by
> including this downstream &removed_region (of size 0x1A00000) +
> previously unreserved downstream memory region (of size 0x200000), to
> align with the starting address of &qseecom_mem?
>
Yes
Regards,
Bjorn
> I just gave this &tz_mem change a spin and I do not see any obvious
> regression in my limited smoke testing (Boots AOSP to UI with
> v5.9-rc1. Touch/BT/WiFi works) so far, with 20+ out-of-tree patches.
>
> Regards,
> Amit Pundir
>
> >
> > Regards,
> > Bjorn