hi,
This series adds support for the SK Hynix Hi-846 CMOS images sensor.
It includes the dt-bindings and the driver.
best wishes,
martin
revision history
----------------
v9: (thank you Pavel and Sakari)
* fix the probe() error paths (that I broke in v8)
* cheanups
v8: (thank you Laurent)
* add fwnode properties support for orientation and rotation on the board
* remove the arm64 defconfig addition patch. deal with that later.
* https://lore.kernel.org/linux-media/[email protected]/
v7: (thank you Sakari)
* move the check for supported nr_lanes for a mode to set_format()
* change get_selection() according to the Sakaris' review
* check for the mipi link frequencies from DT
* check for the external clock rate and add assigned-clock-rates requirement
* https://lore.kernel.org/linux-media/[email protected]/
v6:
* better digital gain defaults
* lane config fix found by smatch
* fix regulator usage in power_on()
* https://lore.kernel.org/linux-media/[email protected]/
v5: (thank you Laurent and Rob)
* minor dt-bindings fixes
* driver: disable lens shading correcting (no seed values yet used from "otp" for that)
* add reviewed-tags
* https://lore.kernel.org/linux-media/[email protected]/
v4: (thank you Laurent, Sakari and Rob) many driver changes, see v3 review for
details. they include:
* add get_selection(), remove open() callback
* use gpiod API
* use regulator_bulk API
* fix power supply timing sequence and bindings
* https://lore.kernel.org/linux-media/[email protected]/
v3: (thank you, Laurent)
* use do_div() for divisions
* reset-gpios DT property name instead of rst-gpios
* improve the dt-bindings
* add the phone-devel list
* https://lore.kernel.org/linux-media/[email protected]/
v2:
sent a bit early due to stupid mistakes
* fix build issues
* fix dtschema issues
* add enable for arm64 defconfig
* https://lore.kernel.org/linux-media/[email protected]/T/#t
v1:
* https://lore.kernel.org/linux-media/[email protected]/
Martin Kepplinger (4):
dt-bindings: vendor-prefixes: Add SK Hynix Inc.
dt-bindings: media: document SK Hynix Hi-846 MIPI CSI-2 8M pixel
sensor
media: i2c: add driver for the SK Hynix Hi-846 8M pixel camera
Documentation: i2c-cardlist: add the Hynix hi846 sensor
.../admin-guide/media/i2c-cardlist.rst | 1 +
.../bindings/media/i2c/hynix,hi846.yaml | 120 +
.../devicetree/bindings/vendor-prefixes.yaml | 2 +
MAINTAINERS | 6 +
drivers/media/i2c/Kconfig | 13 +
drivers/media/i2c/Makefile | 1 +
drivers/media/i2c/hi846.c | 2190 +++++++++++++++++
7 files changed, 2333 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
create mode 100644 drivers/media/i2c/hi846.c
--
2.30.2
Document the bindings used for the SK Hynix Hi-846 CMOS camera driver.
Signed-off-by: Martin Kepplinger <[email protected]>
Reviewed-by: Laurent Pinchart <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
---
.../bindings/media/i2c/hynix,hi846.yaml | 120 ++++++++++++++++++
1 file changed, 120 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
diff --git a/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
new file mode 100644
index 000000000000..85a8877c2f38
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
@@ -0,0 +1,120 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/hynix,hi846.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: SK Hynix Hi-846 1/4" 8M Pixel MIPI CSI-2 sensor
+
+maintainers:
+ - Martin Kepplinger <[email protected]>
+
+description: |-
+ The Hi-846 is a raw image sensor with an MIPI CSI-2 image data
+ interface and CCI (I2C compatible) control bus. The output format
+ is raw Bayer.
+
+properties:
+ compatible:
+ const: hynix,hi846
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ items:
+ - description: Reference to the mclk clock.
+
+ assigned-clocks:
+ maxItems: 1
+
+ assigned-clock-rates:
+ maxItems: 1
+
+ reset-gpios:
+ description: Reference to the GPIO connected to the RESETB pin. Active low.
+ maxItems: 1
+
+ shutdown-gpios:
+ description: Reference to the GPIO connected to the XSHUTDOWN pin. Active low.
+ maxItems: 1
+
+ vddio-supply:
+ description: Definition of the regulator used for the VDDIO power supply.
+
+ vdda-supply:
+ description: Definition of the regulator used for the VDDA power supply.
+
+ vddd-supply:
+ description: Definition of the regulator used for the VDDD power supply.
+
+ port:
+ $ref: /schemas/graph.yaml#/properties/port
+
+ properties:
+ endpoint:
+ $ref: /schemas/media/video-interfaces.yaml#
+ unevaluatedProperties: false
+
+ properties:
+ data-lanes:
+ oneOf:
+ - items:
+ - const: 1
+ - const: 2
+ - const: 3
+ - const: 4
+ - items:
+ - const: 1
+ - const: 2
+
+ required:
+ - data-lanes
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - assigned-clocks
+ - assigned-clock-rates
+ - vddio-supply
+ - vdda-supply
+ - vddd-supply
+ - port
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hi846: camera@20 {
+ compatible = "hynix,hi846";
+ reg = <0x20>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_csi1>;
+ clocks = <&clk 0>;
+ assigned-clocks = <&clk 0>;
+ assigned-clock-rates = <25000000>;
+ vdda-supply = <®_camera_vdda>;
+ vddd-supply = <®_camera_vddd>;
+ vddio-supply = <®_camera_vddio>;
+ reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ shutdown-gpios = <&gpio5 4 GPIO_ACTIVE_LOW>;
+
+ port {
+ camera_out: endpoint {
+ remote-endpoint = <&csi1_ep1>;
+ link-frequencies = /bits/ 64
+ <80000000 200000000>;
+ data-lanes = <1 2>;
+ };
+ };
+ };
+ };
+
+...
--
2.30.2
Add the SK Hynix Hi-846 8M Pixel CMOS image sensor to the i2c-cardlist.
Signed-off-by: Martin Kepplinger <[email protected]>
---
Documentation/admin-guide/media/i2c-cardlist.rst | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/admin-guide/media/i2c-cardlist.rst b/Documentation/admin-guide/media/i2c-cardlist.rst
index e60d459d18a9..185e07a3da43 100644
--- a/Documentation/admin-guide/media/i2c-cardlist.rst
+++ b/Documentation/admin-guide/media/i2c-cardlist.rst
@@ -60,6 +60,7 @@ Driver Name
============ ==========================================================
et8ek8 ET8EK8 camera sensor
hi556 Hynix Hi-556 sensor
+hi846 Hynix Hi-846 sensor
imx214 Sony IMX214 sensor
imx219 Sony IMX219 sensor
imx258 Sony IMX258 sensor
--
2.30.2
SK Hynix built the already supported hi556 sensor (and probably much
more). For more information, see https://www.skhynix.com/
Signed-off-by: Martin Kepplinger <[email protected]>
Acked-by: Rob Herring <[email protected]>
---
Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index a867f7102c35..952553759ac4 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -509,6 +509,8 @@ patternProperties:
description: Hycon Technology Corp.
"^hydis,.*":
description: Hydis Technologies
+ "^hynix,.*":
+ description: SK Hynix Inc.
"^hyundai,.*":
description: Hyundai Technology
"^i2se,.*":
--
2.30.2
The SK Hynix Hi-846 is a 1/4" 8M Pixel CMOS Image Sensor. It supports
usual features like I2C control, CSI-2 for frame data, digital/analog
gain control or test patterns.
This driver supports the 640x480, 1280x720 and 1632x1224 resolution
modes. It supports runtime PM in order not to draw any unnecessary power.
The part is also called YACG4D0C9SHC and a datasheet can be found at
https://product.skhynix.com/products/cis/cis.go
The large sets of partly undocumented register values are for example
found when searching for the hi846_mipi_raw_Sensor.c Android driver.
Signed-off-by: Martin Kepplinger <[email protected]>
Reviewed-by: Pavel Machek <[email protected]>
---
MAINTAINERS | 6 +
drivers/media/i2c/Kconfig | 13 +
drivers/media/i2c/Makefile | 1 +
drivers/media/i2c/hi846.c | 2190 ++++++++++++++++++++++++++++++++++++
4 files changed, 2210 insertions(+)
create mode 100644 drivers/media/i2c/hi846.c
diff --git a/MAINTAINERS b/MAINTAINERS
index f58dad1a1922..0d9cbb1a4250 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -8670,6 +8670,12 @@ S: Maintained
T: git git://linuxtv.org/media_tree.git
F: drivers/media/i2c/hi556.c
+HYNIX HI846 SENSOR DRIVER
+M: Martin Kepplinger <[email protected]>
+L: [email protected]
+S: Maintained
+F: drivers/media/i2c/hi846.c
+
Hyper-V/Azure CORE AND DRIVERS
M: "K. Y. Srinivasan" <[email protected]>
M: Haiyang Zhang <[email protected]>
diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
index cfbcda1f7e48..977facc9195e 100644
--- a/drivers/media/i2c/Kconfig
+++ b/drivers/media/i2c/Kconfig
@@ -742,6 +742,19 @@ config VIDEO_HI556
To compile this driver as a module, choose M here: the
module will be called hi556.
+config VIDEO_HI846
+ tristate "Hynix Hi-846 sensor support"
+ depends on I2C && VIDEO_V4L2
+ select MEDIA_CONTROLLER
+ select VIDEO_V4L2_SUBDEV_API
+ select V4L2_FWNODE
+ help
+ This is a Video4Linux2 sensor driver for the Hynix
+ Hi-846 camera.
+
+ To compile this driver as a module, choose M here: the
+ module will be called hi846.
+
config VIDEO_IMX208
tristate "Sony IMX208 sensor support"
depends on I2C && VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API
diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
index 5ac8d639e5ca..4d4fe08d7a6a 100644
--- a/drivers/media/i2c/Makefile
+++ b/drivers/media/i2c/Makefile
@@ -118,6 +118,7 @@ obj-$(CONFIG_VIDEO_ML86V7667) += ml86v7667.o
obj-$(CONFIG_VIDEO_OV2659) += ov2659.o
obj-$(CONFIG_VIDEO_TC358743) += tc358743.o
obj-$(CONFIG_VIDEO_HI556) += hi556.o
+obj-$(CONFIG_VIDEO_HI846) += hi846.o
obj-$(CONFIG_VIDEO_IMX208) += imx208.o
obj-$(CONFIG_VIDEO_IMX214) += imx214.o
obj-$(CONFIG_VIDEO_IMX219) += imx219.o
diff --git a/drivers/media/i2c/hi846.c b/drivers/media/i2c/hi846.c
new file mode 100644
index 000000000000..822ce3021fde
--- /dev/null
+++ b/drivers/media/i2c/hi846.c
@@ -0,0 +1,2190 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2021 Purism SPC
+
+#include <asm/unaligned.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/of_graph.h>
+#include <linux/pm_runtime.h>
+#include <linux/pm.h>
+#include <linux/regulator/consumer.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-fwnode.h>
+
+#define HI846_MEDIA_BUS_FORMAT MEDIA_BUS_FMT_SGBRG10_1X10
+#define HI846_RGB_DEPTH 10
+
+/* Frame length lines / vertical timings */
+#define HI846_REG_FLL 0x0006
+#define HI846_FLL_MAX 0xffff
+
+/* Horizontal timing */
+#define HI846_REG_LLP 0x0008
+#define HI846_LINE_LENGTH 3800
+
+#define HI846_REG_BINNING_MODE 0x000c
+
+#define HI846_REG_IMAGE_ORIENTATION 0x000e
+
+#define HI846_REG_UNKNOWN_0022 0x0022
+
+#define HI846_REG_Y_ADDR_START_VACT_H 0x0026
+#define HI846_REG_Y_ADDR_START_VACT_L 0x0027
+#define HI846_REG_UNKNOWN_0028 0x0028
+
+#define HI846_REG_Y_ADDR_END_VACT_H 0x002c
+#define HI846_REG_Y_ADDR_END_VACT_L 0x002d
+
+#define HI846_REG_Y_ODD_INC_FOBP 0x002e
+#define HI846_REG_Y_EVEN_INC_FOBP 0x002f
+
+#define HI846_REG_Y_ODD_INC_VACT 0x0032
+#define HI846_REG_Y_EVEN_INC_VACT 0x0033
+
+#define HI846_REG_GROUPED_PARA_HOLD 0x0046
+
+#define HI846_REG_TG_ENABLE 0x004c
+
+#define HI846_REG_UNKNOWN_005C 0x005c
+
+#define HI846_REG_UNKNOWN_006A 0x006a
+
+/*
+ * Long exposure time. Actually, exposure is a 20 bit value that
+ * includes the lower 4 bits of 0x0073 too. Only 16 bits are used
+ * right now
+ */
+#define HI846_REG_EXPOSURE 0x0074
+#define HI846_EXPOSURE_MIN 6
+#define HI846_EXPOSURE_MAX_MARGIN 2
+#define HI846_EXPOSURE_STEP 1
+
+/* Analog gain controls from sensor */
+#define HI846_REG_ANALOG_GAIN 0x0077
+#define HI846_ANAL_GAIN_MIN 0
+#define HI846_ANAL_GAIN_MAX 240
+#define HI846_ANAL_GAIN_STEP 8
+
+/* Digital gain controls from sensor */
+#define HI846_REG_MWB_GR_GAIN_H 0x0078
+#define HI846_REG_MWB_GR_GAIN_L 0x0079
+#define HI846_REG_MWB_GB_GAIN_H 0x007a
+#define HI846_REG_MWB_GB_GAIN_L 0x007b
+#define HI846_REG_MWB_R_GAIN_H 0x007c
+#define HI846_REG_MWB_R_GAIN_L 0x007d
+#define HI846_REG_MWB_B_GAIN_H 0x007e
+#define HI846_REG_MWB_B_GAIN_L 0x007f
+#define HI846_DGTL_GAIN_MIN 512
+#define HI846_DGTL_GAIN_MAX 8191
+#define HI846_DGTL_GAIN_STEP 1
+#define HI846_DGTL_GAIN_DEFAULT 512
+
+#define HI846_REG_X_ADDR_START_HACT_H 0x0120
+#define HI846_REG_X_ADDR_END_HACT_H 0x0122
+
+#define HI846_REG_UNKNOWN_012A 0x012a
+
+#define HI846_REG_UNKNOWN_0200 0x0200
+
+#define HI846_REG_UNKNOWN_021C 0x021c
+#define HI846_REG_UNKNOWN_021E 0x021e
+
+#define HI846_REG_UNKNOWN_0402 0x0402
+#define HI846_REG_UNKNOWN_0404 0x0404
+#define HI846_REG_UNKNOWN_0408 0x0408
+#define HI846_REG_UNKNOWN_0410 0x0410
+#define HI846_REG_UNKNOWN_0412 0x0412
+#define HI846_REG_UNKNOWN_0414 0x0414
+
+#define HI846_REG_UNKNOWN_0418 0x0418
+
+#define HI846_REG_UNKNOWN_051E 0x051e
+
+/* Formatter */
+#define HI846_REG_X_START_H 0x0804
+#define HI846_REG_X_START_L 0x0805
+
+/* MIPI */
+#define HI846_REG_UNKNOWN_0900 0x0900
+#define HI846_REG_MIPI_TX_OP_EN 0x0901
+#define HI846_REG_MIPI_TX_OP_MODE 0x0902
+#define HI846_RAW8 BIT(5)
+
+#define HI846_REG_UNKNOWN_090C 0x090c
+#define HI846_REG_UNKNOWN_090E 0x090e
+
+#define HI846_REG_UNKNOWN_0914 0x0914
+#define HI846_REG_TLPX 0x0915
+#define HI846_REG_TCLK_PREPARE 0x0916
+#define HI846_REG_TCLK_ZERO 0x0917
+#define HI846_REG_UNKNOWN_0918 0x0918
+#define HI846_REG_THS_PREPARE 0x0919
+#define HI846_REG_THS_ZERO 0x091a
+#define HI846_REG_THS_TRAIL 0x091b
+#define HI846_REG_TCLK_POST 0x091c
+#define HI846_REG_TCLK_TRAIL_MIN 0x091d
+#define HI846_REG_UNKNOWN_091E 0x091e
+
+#define HI846_REG_UNKNOWN_0954 0x0954
+#define HI846_REG_UNKNOWN_0956 0x0956
+#define HI846_REG_UNKNOWN_0958 0x0958
+#define HI846_REG_UNKNOWN_095A 0x095a
+
+/* ISP Common */
+#define HI846_REG_MODE_SELECT 0x0a00
+#define HI846_MODE_STANDBY 0x00
+#define HI846_MODE_STREAMING 0x01
+#define HI846_REG_FAST_STANDBY_MODE 0x0a02
+#define HI846_REG_ISP_EN_H 0x0a04
+
+/* Test Pattern Control */
+#define HI846_REG_ISP 0x0a05
+#define HI846_REG_ISP_TPG_EN 0x01
+#define HI846_REG_TEST_PATTERN 0x020a /* 1-9 */
+
+#define HI846_REG_UNKNOWN_0A0C 0x0a0c
+
+/* Windowing */
+#define HI846_REG_X_OUTPUT_SIZE_H 0x0a12
+#define HI846_REG_X_OUTPUT_SIZE_L 0x0a13
+#define HI846_REG_Y_OUTPUT_SIZE_H 0x0a14
+#define HI846_REG_Y_OUTPUT_SIZE_L 0x0a15
+
+/* ISP Common */
+#define HI846_REG_PEDESTAL_EN 0x0a1a
+
+#define HI846_REG_UNKNOWN_0A1E 0x0a1e
+
+/* Horizontal Binning Mode */
+#define HI846_REG_HBIN_MODE 0x0a22
+
+#define HI846_REG_UNKNOWN_0A24 0x0a24
+#define HI846_REG_UNKNOWN_0B02 0x0b02
+#define HI846_REG_UNKNOWN_0B10 0x0b10
+#define HI846_REG_UNKNOWN_0B12 0x0b12
+#define HI846_REG_UNKNOWN_0B14 0x0b14
+
+/* BLC (Black Level Calibration) */
+#define HI846_REG_BLC_CTL0 0x0c00
+
+#define HI846_REG_UNKNOWN_0C06 0x0c06
+#define HI846_REG_UNKNOWN_0C10 0x0c10
+#define HI846_REG_UNKNOWN_0C12 0x0c12
+#define HI846_REG_UNKNOWN_0C14 0x0c14
+#define HI846_REG_UNKNOWN_0C16 0x0c16
+
+#define HI846_REG_UNKNOWN_0E04 0x0e04
+
+#define HI846_REG_CHIP_ID_L 0x0f16
+#define HI846_REG_CHIP_ID_H 0x0f17
+#define HI846_CHIP_ID_L 0x46
+#define HI846_CHIP_ID_H 0x08
+
+#define HI846_REG_UNKNOWN_0F04 0x0f04
+#define HI846_REG_UNKNOWN_0F08 0x0f08
+
+/* PLL */
+#define HI846_REG_PLL_CFG_MIPI2_H 0x0f2a
+#define HI846_REG_PLL_CFG_MIPI2_L 0x0f2b
+
+#define HI846_REG_UNKNOWN_0F30 0x0f30
+#define HI846_REG_PLL_CFG_RAMP1_H 0x0f32
+#define HI846_REG_UNKNOWN_0F36 0x0f36
+#define HI846_REG_PLL_CFG_MIPI1_H 0x0f38
+
+#define HI846_REG_UNKNOWN_2008 0x2008
+#define HI846_REG_UNKNOWN_326E 0x326e
+
+struct hi846_reg {
+ u16 address;
+ u16 val;
+};
+
+struct hi846_reg_list {
+ u32 num_of_regs;
+ const struct hi846_reg *regs;
+};
+
+struct hi846_mode {
+ /* Frame width in pixels */
+ u32 width;
+
+ /* Frame height in pixels */
+ u32 height;
+
+ /* Horizontal timing size */
+ u32 llp;
+
+ /* Link frequency needed for this resolution */
+ u8 link_freq_index;
+
+ u16 fps;
+
+ /* Vertical timining size */
+ u16 frame_len;
+
+ const struct hi846_reg_list reg_list_config;
+ const struct hi846_reg_list reg_list_2lane;
+ const struct hi846_reg_list reg_list_4lane;
+
+ /* Position inside of the 3264x2448 pixel array */
+ struct v4l2_rect crop;
+};
+
+static const struct hi846_reg hi846_init_2lane[] = {
+ {HI846_REG_MODE_SELECT, 0x0000},
+ /* regs below are unknown */
+ {0x2000, 0x100a},
+ {0x2002, 0x00ff},
+ {0x2004, 0x0007},
+ {0x2006, 0x3fff},
+ {0x2008, 0x3fff},
+ {0x200a, 0xc216},
+ {0x200c, 0x1292},
+ {0x200e, 0xc01a},
+ {0x2010, 0x403d},
+ {0x2012, 0x000e},
+ {0x2014, 0x403e},
+ {0x2016, 0x0b80},
+ {0x2018, 0x403f},
+ {0x201a, 0x82ae},
+ {0x201c, 0x1292},
+ {0x201e, 0xc00c},
+ {0x2020, 0x4130},
+ {0x2022, 0x43e2},
+ {0x2024, 0x0180},
+ {0x2026, 0x4130},
+ {0x2028, 0x7400},
+ {0x202a, 0x5000},
+ {0x202c, 0x0253},
+ {0x202e, 0x0ad1},
+ {0x2030, 0x2360},
+ {0x2032, 0x0009},
+ {0x2034, 0x5020},
+ {0x2036, 0x000b},
+ {0x2038, 0x0002},
+ {0x203a, 0x0044},
+ {0x203c, 0x0016},
+ {0x203e, 0x1792},
+ {0x2040, 0x7002},
+ {0x2042, 0x154f},
+ {0x2044, 0x00d5},
+ {0x2046, 0x000b},
+ {0x2048, 0x0019},
+ {0x204a, 0x1698},
+ {0x204c, 0x000e},
+ {0x204e, 0x099a},
+ {0x2050, 0x0058},
+ {0x2052, 0x7000},
+ {0x2054, 0x1799},
+ {0x2056, 0x0310},
+ {0x2058, 0x03c3},
+ {0x205a, 0x004c},
+ {0x205c, 0x064a},
+ {0x205e, 0x0001},
+ {0x2060, 0x0007},
+ {0x2062, 0x0bc7},
+ {0x2064, 0x0055},
+ {0x2066, 0x7000},
+ {0x2068, 0x1550},
+ {0x206a, 0x158a},
+ {0x206c, 0x0004},
+ {0x206e, 0x1488},
+ {0x2070, 0x7010},
+ {0x2072, 0x1508},
+ {0x2074, 0x0004},
+ {0x2076, 0x0016},
+ {0x2078, 0x03d5},
+ {0x207a, 0x0055},
+ {0x207c, 0x08ca},
+ {0x207e, 0x2019},
+ {0x2080, 0x0007},
+ {0x2082, 0x7057},
+ {0x2084, 0x0fc7},
+ {0x2086, 0x5041},
+ {0x2088, 0x12c8},
+ {0x208a, 0x5060},
+ {0x208c, 0x5080},
+ {0x208e, 0x2084},
+ {0x2090, 0x12c8},
+ {0x2092, 0x7800},
+ {0x2094, 0x0802},
+ {0x2096, 0x040f},
+ {0x2098, 0x1007},
+ {0x209a, 0x0803},
+ {0x209c, 0x080b},
+ {0x209e, 0x3803},
+ {0x20a0, 0x0807},
+ {0x20a2, 0x0404},
+ {0x20a4, 0x0400},
+ {0x20a6, 0xffff},
+ {0x20a8, 0xf0b2},
+ {0x20aa, 0xffef},
+ {0x20ac, 0x0a84},
+ {0x20ae, 0x1292},
+ {0x20b0, 0xc02e},
+ {0x20b2, 0x4130},
+ {0x23fe, 0xc056},
+ {0x3232, 0xfc0c},
+ {0x3236, 0xfc22},
+ {0x3248, 0xfca8},
+ {0x326a, 0x8302},
+ {0x326c, 0x830a},
+ {0x326e, 0x0000},
+ {0x32ca, 0xfc28},
+ {0x32cc, 0xc3bc},
+ {0x32ce, 0xc34c},
+ {0x32d0, 0xc35a},
+ {0x32d2, 0xc368},
+ {0x32d4, 0xc376},
+ {0x32d6, 0xc3c2},
+ {0x32d8, 0xc3e6},
+ {0x32da, 0x0003},
+ {0x32dc, 0x0003},
+ {0x32de, 0x00c7},
+ {0x32e0, 0x0031},
+ {0x32e2, 0x0031},
+ {0x32e4, 0x0031},
+ {0x32e6, 0xfc28},
+ {0x32e8, 0xc3bc},
+ {0x32ea, 0xc384},
+ {0x32ec, 0xc392},
+ {0x32ee, 0xc3a0},
+ {0x32f0, 0xc3ae},
+ {0x32f2, 0xc3c4},
+ {0x32f4, 0xc3e6},
+ {0x32f6, 0x0003},
+ {0x32f8, 0x0003},
+ {0x32fa, 0x00c7},
+ {0x32fc, 0x0031},
+ {0x32fe, 0x0031},
+ {0x3300, 0x0031},
+ {0x3302, 0x82ca},
+ {0x3304, 0xc164},
+ {0x3306, 0x82e6},
+ {0x3308, 0xc19c},
+ {0x330a, 0x001f},
+ {0x330c, 0x001a},
+ {0x330e, 0x0034},
+ {0x3310, 0x0000},
+ {0x3312, 0x0000},
+ {0x3314, 0xfc94},
+ {0x3316, 0xc3d8},
+ /* regs above are unknown */
+ {HI846_REG_MODE_SELECT, 0x0000},
+ {HI846_REG_UNKNOWN_0E04, 0x0012},
+ {HI846_REG_Y_ODD_INC_FOBP, 0x1111},
+ {HI846_REG_Y_ODD_INC_VACT, 0x1111},
+ {HI846_REG_UNKNOWN_0022, 0x0008},
+ {HI846_REG_Y_ADDR_START_VACT_H, 0x0040},
+ {HI846_REG_UNKNOWN_0028, 0x0017},
+ {HI846_REG_Y_ADDR_END_VACT_H, 0x09cf},
+ {HI846_REG_UNKNOWN_005C, 0x2101},
+ {HI846_REG_FLL, 0x09de},
+ {HI846_REG_LLP, 0x0ed8},
+ {HI846_REG_IMAGE_ORIENTATION, 0x0100},
+ {HI846_REG_BINNING_MODE, 0x0022},
+ {HI846_REG_HBIN_MODE, 0x0000},
+ {HI846_REG_UNKNOWN_0A24, 0x0000},
+ {HI846_REG_X_START_H, 0x0000},
+ {HI846_REG_X_OUTPUT_SIZE_H, 0x0cc0},
+ {HI846_REG_Y_OUTPUT_SIZE_H, 0x0990},
+ {HI846_REG_EXPOSURE, 0x09d8},
+ {HI846_REG_ANALOG_GAIN, 0x0000},
+ {HI846_REG_GROUPED_PARA_HOLD, 0x0000},
+ {HI846_REG_UNKNOWN_051E, 0x0000},
+ {HI846_REG_UNKNOWN_0200, 0x0400},
+ {HI846_REG_PEDESTAL_EN, 0x0c00},
+ {HI846_REG_UNKNOWN_0A0C, 0x0010},
+ {HI846_REG_UNKNOWN_0A1E, 0x0ccf},
+ {HI846_REG_UNKNOWN_0402, 0x0110},
+ {HI846_REG_UNKNOWN_0404, 0x00f4},
+ {HI846_REG_UNKNOWN_0408, 0x0000},
+ {HI846_REG_UNKNOWN_0410, 0x008d},
+ {HI846_REG_UNKNOWN_0412, 0x011a},
+ {HI846_REG_UNKNOWN_0414, 0x864c},
+ {HI846_REG_UNKNOWN_021C, 0x0003},
+ {HI846_REG_UNKNOWN_021E, 0x0235},
+ {HI846_REG_BLC_CTL0, 0x9150},
+ {HI846_REG_UNKNOWN_0C06, 0x0021},
+ {HI846_REG_UNKNOWN_0C10, 0x0040},
+ {HI846_REG_UNKNOWN_0C12, 0x0040},
+ {HI846_REG_UNKNOWN_0C14, 0x0040},
+ {HI846_REG_UNKNOWN_0C16, 0x0040},
+ {HI846_REG_FAST_STANDBY_MODE, 0x0100},
+ {HI846_REG_ISP_EN_H, 0x014a},
+ {HI846_REG_UNKNOWN_0418, 0x0000},
+ {HI846_REG_UNKNOWN_012A, 0x03b4},
+ {HI846_REG_X_ADDR_START_HACT_H, 0x0046},
+ {HI846_REG_X_ADDR_END_HACT_H, 0x0376},
+ {HI846_REG_UNKNOWN_0B02, 0xe04d},
+ {HI846_REG_UNKNOWN_0B10, 0x6821},
+ {HI846_REG_UNKNOWN_0B12, 0x0120},
+ {HI846_REG_UNKNOWN_0B14, 0x0001},
+ {HI846_REG_UNKNOWN_2008, 0x38fd},
+ {HI846_REG_UNKNOWN_326E, 0x0000},
+ {HI846_REG_UNKNOWN_0900, 0x0320},
+ {HI846_REG_MIPI_TX_OP_MODE, 0xc31a},
+ {HI846_REG_UNKNOWN_0914, 0xc109},
+ {HI846_REG_TCLK_PREPARE, 0x061a},
+ {HI846_REG_UNKNOWN_0918, 0x0306},
+ {HI846_REG_THS_ZERO, 0x0b09},
+ {HI846_REG_TCLK_POST, 0x0c07},
+ {HI846_REG_UNKNOWN_091E, 0x0a00},
+ {HI846_REG_UNKNOWN_090C, 0x042a},
+ {HI846_REG_UNKNOWN_090E, 0x006b},
+ {HI846_REG_UNKNOWN_0954, 0x0089},
+ {HI846_REG_UNKNOWN_0956, 0x0000},
+ {HI846_REG_UNKNOWN_0958, 0xca00},
+ {HI846_REG_UNKNOWN_095A, 0x9240},
+ {HI846_REG_UNKNOWN_0F08, 0x2f04},
+ {HI846_REG_UNKNOWN_0F30, 0x001f},
+ {HI846_REG_UNKNOWN_0F36, 0x001f},
+ {HI846_REG_UNKNOWN_0F04, 0x3a00},
+ {HI846_REG_PLL_CFG_RAMP1_H, 0x025a},
+ {HI846_REG_PLL_CFG_MIPI1_H, 0x025a},
+ {HI846_REG_PLL_CFG_MIPI2_H, 0x0024},
+ {HI846_REG_UNKNOWN_006A, 0x0100},
+ {HI846_REG_TG_ENABLE, 0x0100},
+};
+
+static const struct hi846_reg hi846_init_4lane[] = {
+ {0x2000, 0x987a},
+ {0x2002, 0x00ff},
+ {0x2004, 0x0047},
+ {0x2006, 0x3fff},
+ {0x2008, 0x3fff},
+ {0x200a, 0xc216},
+ {0x200c, 0x1292},
+ {0x200e, 0xc01a},
+ {0x2010, 0x403d},
+ {0x2012, 0x000e},
+ {0x2014, 0x403e},
+ {0x2016, 0x0b80},
+ {0x2018, 0x403f},
+ {0x201a, 0x82ae},
+ {0x201c, 0x1292},
+ {0x201e, 0xc00c},
+ {0x2020, 0x4130},
+ {0x2022, 0x43e2},
+ {0x2024, 0x0180},
+ {0x2026, 0x4130},
+ {0x2028, 0x7400},
+ {0x202a, 0x5000},
+ {0x202c, 0x0253},
+ {0x202e, 0x0ad1},
+ {0x2030, 0x2360},
+ {0x2032, 0x0009},
+ {0x2034, 0x5020},
+ {0x2036, 0x000b},
+ {0x2038, 0x0002},
+ {0x203a, 0x0044},
+ {0x203c, 0x0016},
+ {0x203e, 0x1792},
+ {0x2040, 0x7002},
+ {0x2042, 0x154f},
+ {0x2044, 0x00d5},
+ {0x2046, 0x000b},
+ {0x2048, 0x0019},
+ {0x204a, 0x1698},
+ {0x204c, 0x000e},
+ {0x204e, 0x099a},
+ {0x2050, 0x0058},
+ {0x2052, 0x7000},
+ {0x2054, 0x1799},
+ {0x2056, 0x0310},
+ {0x2058, 0x03c3},
+ {0x205a, 0x004c},
+ {0x205c, 0x064a},
+ {0x205e, 0x0001},
+ {0x2060, 0x0007},
+ {0x2062, 0x0bc7},
+ {0x2064, 0x0055},
+ {0x2066, 0x7000},
+ {0x2068, 0x1550},
+ {0x206a, 0x158a},
+ {0x206c, 0x0004},
+ {0x206e, 0x1488},
+ {0x2070, 0x7010},
+ {0x2072, 0x1508},
+ {0x2074, 0x0004},
+ {0x2076, 0x0016},
+ {0x2078, 0x03d5},
+ {0x207a, 0x0055},
+ {0x207c, 0x08ca},
+ {0x207e, 0x2019},
+ {0x2080, 0x0007},
+ {0x2082, 0x7057},
+ {0x2084, 0x0fc7},
+ {0x2086, 0x5041},
+ {0x2088, 0x12c8},
+ {0x208a, 0x5060},
+ {0x208c, 0x5080},
+ {0x208e, 0x2084},
+ {0x2090, 0x12c8},
+ {0x2092, 0x7800},
+ {0x2094, 0x0802},
+ {0x2096, 0x040f},
+ {0x2098, 0x1007},
+ {0x209a, 0x0803},
+ {0x209c, 0x080b},
+ {0x209e, 0x3803},
+ {0x20a0, 0x0807},
+ {0x20a2, 0x0404},
+ {0x20a4, 0x0400},
+ {0x20a6, 0xffff},
+ {0x20a8, 0xf0b2},
+ {0x20aa, 0xffef},
+ {0x20ac, 0x0a84},
+ {0x20ae, 0x1292},
+ {0x20b0, 0xc02e},
+ {0x20b2, 0x4130},
+ {0x20b4, 0xf0b2},
+ {0x20b6, 0xffbf},
+ {0x20b8, 0x2004},
+ {0x20ba, 0x403f},
+ {0x20bc, 0x00c3},
+ {0x20be, 0x4fe2},
+ {0x20c0, 0x8318},
+ {0x20c2, 0x43cf},
+ {0x20c4, 0x0000},
+ {0x20c6, 0x9382},
+ {0x20c8, 0xc314},
+ {0x20ca, 0x2003},
+ {0x20cc, 0x12b0},
+ {0x20ce, 0xcab0},
+ {0x20d0, 0x4130},
+ {0x20d2, 0x12b0},
+ {0x20d4, 0xc90a},
+ {0x20d6, 0x4130},
+ {0x20d8, 0x42d2},
+ {0x20da, 0x8318},
+ {0x20dc, 0x00c3},
+ {0x20de, 0x9382},
+ {0x20e0, 0xc314},
+ {0x20e2, 0x2009},
+ {0x20e4, 0x120b},
+ {0x20e6, 0x120a},
+ {0x20e8, 0x1209},
+ {0x20ea, 0x1208},
+ {0x20ec, 0x1207},
+ {0x20ee, 0x1206},
+ {0x20f0, 0x4030},
+ {0x20f2, 0xc15e},
+ {0x20f4, 0x4130},
+ {0x20f6, 0x1292},
+ {0x20f8, 0xc008},
+ {0x20fa, 0x4130},
+ {0x20fc, 0x42d2},
+ {0x20fe, 0x82a1},
+ {0x2100, 0x00c2},
+ {0x2102, 0x1292},
+ {0x2104, 0xc040},
+ {0x2106, 0x4130},
+ {0x2108, 0x1292},
+ {0x210a, 0xc006},
+ {0x210c, 0x42a2},
+ {0x210e, 0x7324},
+ {0x2110, 0x9382},
+ {0x2112, 0xc314},
+ {0x2114, 0x2011},
+ {0x2116, 0x425f},
+ {0x2118, 0x82a1},
+ {0x211a, 0xf25f},
+ {0x211c, 0x00c1},
+ {0x211e, 0xf35f},
+ {0x2120, 0x2406},
+ {0x2122, 0x425f},
+ {0x2124, 0x00c0},
+ {0x2126, 0xf37f},
+ {0x2128, 0x522f},
+ {0x212a, 0x4f82},
+ {0x212c, 0x7324},
+ {0x212e, 0x425f},
+ {0x2130, 0x82d4},
+ {0x2132, 0xf35f},
+ {0x2134, 0x4fc2},
+ {0x2136, 0x01b3},
+ {0x2138, 0x93c2},
+ {0x213a, 0x829f},
+ {0x213c, 0x2421},
+ {0x213e, 0x403e},
+ {0x2140, 0xfffe},
+ {0x2142, 0x40b2},
+ {0x2144, 0xec78},
+ {0x2146, 0x831c},
+ {0x2148, 0x40b2},
+ {0x214a, 0xec78},
+ {0x214c, 0x831e},
+ {0x214e, 0x40b2},
+ {0x2150, 0xec78},
+ {0x2152, 0x8320},
+ {0x2154, 0xb3d2},
+ {0x2156, 0x008c},
+ {0x2158, 0x2405},
+ {0x215a, 0x4e0f},
+ {0x215c, 0x503f},
+ {0x215e, 0xffd8},
+ {0x2160, 0x4f82},
+ {0x2162, 0x831c},
+ {0x2164, 0x90f2},
+ {0x2166, 0x0003},
+ {0x2168, 0x008c},
+ {0x216a, 0x2401},
+ {0x216c, 0x4130},
+ {0x216e, 0x421f},
+ {0x2170, 0x831c},
+ {0x2172, 0x5e0f},
+ {0x2174, 0x4f82},
+ {0x2176, 0x831e},
+ {0x2178, 0x5e0f},
+ {0x217a, 0x4f82},
+ {0x217c, 0x8320},
+ {0x217e, 0x3ff6},
+ {0x2180, 0x432e},
+ {0x2182, 0x3fdf},
+ {0x2184, 0x421f},
+ {0x2186, 0x7100},
+ {0x2188, 0x4f0e},
+ {0x218a, 0x503e},
+ {0x218c, 0xffd8},
+ {0x218e, 0x4e82},
+ {0x2190, 0x7a04},
+ {0x2192, 0x421e},
+ {0x2194, 0x831c},
+ {0x2196, 0x5f0e},
+ {0x2198, 0x4e82},
+ {0x219a, 0x7a06},
+ {0x219c, 0x0b00},
+ {0x219e, 0x7304},
+ {0x21a0, 0x0050},
+ {0x21a2, 0x40b2},
+ {0x21a4, 0xd081},
+ {0x21a6, 0x0b88},
+ {0x21a8, 0x421e},
+ {0x21aa, 0x831e},
+ {0x21ac, 0x5f0e},
+ {0x21ae, 0x4e82},
+ {0x21b0, 0x7a0e},
+ {0x21b2, 0x521f},
+ {0x21b4, 0x8320},
+ {0x21b6, 0x4f82},
+ {0x21b8, 0x7a10},
+ {0x21ba, 0x0b00},
+ {0x21bc, 0x7304},
+ {0x21be, 0x007a},
+ {0x21c0, 0x40b2},
+ {0x21c2, 0x0081},
+ {0x21c4, 0x0b88},
+ {0x21c6, 0x4392},
+ {0x21c8, 0x7a0a},
+ {0x21ca, 0x0800},
+ {0x21cc, 0x7a0c},
+ {0x21ce, 0x0b00},
+ {0x21d0, 0x7304},
+ {0x21d2, 0x022b},
+ {0x21d4, 0x40b2},
+ {0x21d6, 0xd081},
+ {0x21d8, 0x0b88},
+ {0x21da, 0x0b00},
+ {0x21dc, 0x7304},
+ {0x21de, 0x0255},
+ {0x21e0, 0x40b2},
+ {0x21e2, 0x0081},
+ {0x21e4, 0x0b88},
+ {0x21e6, 0x4130},
+ {0x23fe, 0xc056},
+ {0x3232, 0xfc0c},
+ {0x3236, 0xfc22},
+ {0x3238, 0xfcfc},
+ {0x323a, 0xfd84},
+ {0x323c, 0xfd08},
+ {0x3246, 0xfcd8},
+ {0x3248, 0xfca8},
+ {0x324e, 0xfcb4},
+ {0x326a, 0x8302},
+ {0x326c, 0x830a},
+ {0x326e, 0x0000},
+ {0x32ca, 0xfc28},
+ {0x32cc, 0xc3bc},
+ {0x32ce, 0xc34c},
+ {0x32d0, 0xc35a},
+ {0x32d2, 0xc368},
+ {0x32d4, 0xc376},
+ {0x32d6, 0xc3c2},
+ {0x32d8, 0xc3e6},
+ {0x32da, 0x0003},
+ {0x32dc, 0x0003},
+ {0x32de, 0x00c7},
+ {0x32e0, 0x0031},
+ {0x32e2, 0x0031},
+ {0x32e4, 0x0031},
+ {0x32e6, 0xfc28},
+ {0x32e8, 0xc3bc},
+ {0x32ea, 0xc384},
+ {0x32ec, 0xc392},
+ {0x32ee, 0xc3a0},
+ {0x32f0, 0xc3ae},
+ {0x32f2, 0xc3c4},
+ {0x32f4, 0xc3e6},
+ {0x32f6, 0x0003},
+ {0x32f8, 0x0003},
+ {0x32fa, 0x00c7},
+ {0x32fc, 0x0031},
+ {0x32fe, 0x0031},
+ {0x3300, 0x0031},
+ {0x3302, 0x82ca},
+ {0x3304, 0xc164},
+ {0x3306, 0x82e6},
+ {0x3308, 0xc19c},
+ {0x330a, 0x001f},
+ {0x330c, 0x001a},
+ {0x330e, 0x0034},
+ {0x3310, 0x0000},
+ {0x3312, 0x0000},
+ {0x3314, 0xfc94},
+ {0x3316, 0xc3d8},
+
+ {0x0a00, 0x0000},
+ {0x0e04, 0x0012},
+ {0x002e, 0x1111},
+ {0x0032, 0x1111},
+ {0x0022, 0x0008},
+ {0x0026, 0x0040},
+ {0x0028, 0x0017},
+ {0x002c, 0x09cf},
+ {0x005c, 0x2101},
+ {0x0006, 0x09de},
+ {0x0008, 0x0ed8},
+ {0x000e, 0x0100},
+ {0x000c, 0x0022},
+ {0x0a22, 0x0000},
+ {0x0a24, 0x0000},
+ {0x0804, 0x0000},
+ {0x0a12, 0x0cc0},
+ {0x0a14, 0x0990},
+ {0x0074, 0x09d8},
+ {0x0076, 0x0000},
+ {0x051e, 0x0000},
+ {0x0200, 0x0400},
+ {0x0a1a, 0x0c00},
+ {0x0a0c, 0x0010},
+ {0x0a1e, 0x0ccf},
+ {0x0402, 0x0110},
+ {0x0404, 0x00f4},
+ {0x0408, 0x0000},
+ {0x0410, 0x008d},
+ {0x0412, 0x011a},
+ {0x0414, 0x864c},
+ /* for OTP */
+ {0x021c, 0x0003},
+ {0x021e, 0x0235},
+ /* for OTP */
+ {0x0c00, 0x9950},
+ {0x0c06, 0x0021},
+ {0x0c10, 0x0040},
+ {0x0c12, 0x0040},
+ {0x0c14, 0x0040},
+ {0x0c16, 0x0040},
+ {0x0a02, 0x0100},
+ {0x0a04, 0x015a},
+ {0x0418, 0x0000},
+ {0x0128, 0x0028},
+ {0x012a, 0xffff},
+ {0x0120, 0x0046},
+ {0x0122, 0x0376},
+ {0x012c, 0x0020},
+ {0x012e, 0xffff},
+ {0x0124, 0x0040},
+ {0x0126, 0x0378},
+ {0x0746, 0x0050},
+ {0x0748, 0x01d5},
+ {0x074a, 0x022b},
+ {0x074c, 0x03b0},
+ {0x0756, 0x043f},
+ {0x0758, 0x3f1d},
+ {0x0b02, 0xe04d},
+ {0x0b10, 0x6821},
+ {0x0b12, 0x0120},
+ {0x0b14, 0x0001},
+ {0x2008, 0x38fd},
+ {0x326e, 0x0000},
+ {0x0900, 0x0300},
+ {0x0902, 0xc319},
+ {0x0914, 0xc109},
+ {0x0916, 0x061a},
+ {0x0918, 0x0407},
+ {0x091a, 0x0a0b},
+ {0x091c, 0x0e08},
+ {0x091e, 0x0a00},
+ {0x090c, 0x0427},
+ {0x090e, 0x0059},
+ {0x0954, 0x0089},
+ {0x0956, 0x0000},
+ {0x0958, 0xca80},
+ {0x095a, 0x9240},
+ {0x0f08, 0x2f04},
+ {0x0f30, 0x001f},
+ {0x0f36, 0x001f},
+ {0x0f04, 0x3a00},
+ {0x0f32, 0x025a},
+ {0x0f38, 0x025a},
+ {0x0f2a, 0x4124},
+ {0x006a, 0x0100},
+ {0x004c, 0x0100},
+ {0x0044, 0x0001},
+};
+
+static const struct hi846_reg mode_640x480_config[] = {
+ {HI846_REG_MODE_SELECT, 0x0000},
+ {HI846_REG_Y_ODD_INC_FOBP, 0x7711},
+ {HI846_REG_Y_ODD_INC_VACT, 0x7711},
+ {HI846_REG_Y_ADDR_START_VACT_H, 0x0148},
+ {HI846_REG_Y_ADDR_END_VACT_H, 0x08c7},
+ {HI846_REG_UNKNOWN_005C, 0x4404},
+ {HI846_REG_FLL, 0x0277},
+ {HI846_REG_LLP, 0x0ed8},
+ {HI846_REG_BINNING_MODE, 0x0322},
+ {HI846_REG_HBIN_MODE, 0x0200},
+ {HI846_REG_UNKNOWN_0A24, 0x0000},
+ {HI846_REG_X_START_H, 0x0058},
+ {HI846_REG_X_OUTPUT_SIZE_H, 0x0280},
+ {HI846_REG_Y_OUTPUT_SIZE_H, 0x01e0},
+
+ /* For OTP */
+ {HI846_REG_UNKNOWN_021C, 0x0003},
+ {HI846_REG_UNKNOWN_021E, 0x0235},
+
+ {HI846_REG_ISP_EN_H, 0x016a},
+ {HI846_REG_UNKNOWN_0418, 0x0210},
+ {HI846_REG_UNKNOWN_0B02, 0xe04d},
+ {HI846_REG_UNKNOWN_0B10, 0x7021},
+ {HI846_REG_UNKNOWN_0B12, 0x0120},
+ {HI846_REG_UNKNOWN_0B14, 0x0001},
+ {HI846_REG_UNKNOWN_2008, 0x38fd},
+ {HI846_REG_UNKNOWN_326E, 0x0000},
+};
+
+static const struct hi846_reg mode_640x480_mipi_2lane[] = {
+ {HI846_REG_UNKNOWN_0900, 0x0300},
+ {HI846_REG_MIPI_TX_OP_MODE, 0x4319},
+ {HI846_REG_UNKNOWN_0914, 0xc105},
+ {HI846_REG_TCLK_PREPARE, 0x030c},
+ {HI846_REG_UNKNOWN_0918, 0x0304},
+ {HI846_REG_THS_ZERO, 0x0708},
+ {HI846_REG_TCLK_POST, 0x0b04},
+ {HI846_REG_UNKNOWN_091E, 0x0500},
+ {HI846_REG_UNKNOWN_090C, 0x0208},
+ {HI846_REG_UNKNOWN_090E, 0x009a},
+ {HI846_REG_UNKNOWN_0954, 0x0089},
+ {HI846_REG_UNKNOWN_0956, 0x0000},
+ {HI846_REG_UNKNOWN_0958, 0xca80},
+ {HI846_REG_UNKNOWN_095A, 0x9240},
+ {HI846_REG_PLL_CFG_MIPI2_H, 0x4924},
+ {HI846_REG_TG_ENABLE, 0x0100},
+};
+
+static const struct hi846_reg mode_1280x720_config[] = {
+ {HI846_REG_MODE_SELECT, 0x0000},
+ {HI846_REG_Y_ODD_INC_FOBP, 0x3311},
+ {HI846_REG_Y_ODD_INC_VACT, 0x3311},
+ {HI846_REG_Y_ADDR_START_VACT_H, 0x0238},
+ {HI846_REG_Y_ADDR_END_VACT_H, 0x07d7},
+ {HI846_REG_UNKNOWN_005C, 0x4202},
+ {HI846_REG_FLL, 0x034a},
+ {HI846_REG_LLP, 0x0ed8},
+ {HI846_REG_BINNING_MODE, 0x0122},
+ {HI846_REG_HBIN_MODE, 0x0100},
+ {HI846_REG_UNKNOWN_0A24, 0x0000},
+ {HI846_REG_X_START_H, 0x00b0},
+ {HI846_REG_X_OUTPUT_SIZE_H, 0x0500},
+ {HI846_REG_Y_OUTPUT_SIZE_H, 0x02d0},
+ {HI846_REG_EXPOSURE, 0x0344},
+
+ /* For OTP */
+ {HI846_REG_UNKNOWN_021C, 0x0003},
+ {HI846_REG_UNKNOWN_021E, 0x0235},
+
+ {HI846_REG_ISP_EN_H, 0x016a},
+ {HI846_REG_UNKNOWN_0418, 0x0410},
+ {HI846_REG_UNKNOWN_0B02, 0xe04d},
+ {HI846_REG_UNKNOWN_0B10, 0x6c21},
+ {HI846_REG_UNKNOWN_0B12, 0x0120},
+ {HI846_REG_UNKNOWN_0B14, 0x0005},
+ {HI846_REG_UNKNOWN_2008, 0x38fd},
+ {HI846_REG_UNKNOWN_326E, 0x0000},
+};
+
+static const struct hi846_reg mode_1280x720_mipi_2lane[] = {
+ {HI846_REG_UNKNOWN_0900, 0x0300},
+ {HI846_REG_MIPI_TX_OP_MODE, 0x4319},
+ {HI846_REG_UNKNOWN_0914, 0xc109},
+ {HI846_REG_TCLK_PREPARE, 0x061a},
+ {HI846_REG_UNKNOWN_0918, 0x0407},
+ {HI846_REG_THS_ZERO, 0x0a0b},
+ {HI846_REG_TCLK_POST, 0x0e08},
+ {HI846_REG_UNKNOWN_091E, 0x0a00},
+ {HI846_REG_UNKNOWN_090C, 0x0427},
+ {HI846_REG_UNKNOWN_090E, 0x0145},
+ {HI846_REG_UNKNOWN_0954, 0x0089},
+ {HI846_REG_UNKNOWN_0956, 0x0000},
+ {HI846_REG_UNKNOWN_0958, 0xca80},
+ {HI846_REG_UNKNOWN_095A, 0x9240},
+ {HI846_REG_PLL_CFG_MIPI2_H, 0x4124},
+ {HI846_REG_TG_ENABLE, 0x0100},
+};
+
+static const struct hi846_reg mode_1280x720_mipi_4lane[] = {
+ /* 360Mbps */
+ {HI846_REG_UNKNOWN_0900, 0x0300},
+ {HI846_REG_MIPI_TX_OP_MODE, 0xc319},
+ {HI846_REG_UNKNOWN_0914, 0xc105},
+ {HI846_REG_TCLK_PREPARE, 0x030c},
+ {HI846_REG_UNKNOWN_0918, 0x0304},
+ {HI846_REG_THS_ZERO, 0x0708},
+ {HI846_REG_TCLK_POST, 0x0b04},
+ {HI846_REG_UNKNOWN_091E, 0x0500},
+ {HI846_REG_UNKNOWN_090C, 0x0208},
+ {HI846_REG_UNKNOWN_090E, 0x008a},
+ {HI846_REG_UNKNOWN_0954, 0x0089},
+ {HI846_REG_UNKNOWN_0956, 0x0000},
+ {HI846_REG_UNKNOWN_0958, 0xca80},
+ {HI846_REG_UNKNOWN_095A, 0x9240},
+ {HI846_REG_PLL_CFG_MIPI2_H, 0x4924},
+ {HI846_REG_TG_ENABLE, 0x0100},
+};
+
+static const struct hi846_reg mode_1632x1224_config[] = {
+ {HI846_REG_MODE_SELECT, 0x0000},
+ {HI846_REG_Y_ODD_INC_FOBP, 0x3311},
+ {HI846_REG_Y_ODD_INC_VACT, 0x3311},
+ {HI846_REG_Y_ADDR_START_VACT_H, 0x0040},
+ {HI846_REG_Y_ADDR_END_VACT_H, 0x09cf},
+ {HI846_REG_UNKNOWN_005C, 0x4202},
+ {HI846_REG_FLL, 0x09de},
+ {HI846_REG_LLP, 0x0ed8},
+ {HI846_REG_BINNING_MODE, 0x0122},
+ {HI846_REG_HBIN_MODE, 0x0100},
+ {HI846_REG_UNKNOWN_0A24, 0x0000},
+ {HI846_REG_X_START_H, 0x0000},
+ {HI846_REG_X_OUTPUT_SIZE_H, 0x0660},
+ {HI846_REG_Y_OUTPUT_SIZE_H, 0x04c8},
+ {HI846_REG_EXPOSURE, 0x09d8},
+
+ /* For OTP */
+ {HI846_REG_UNKNOWN_021C, 0x0003},
+ {HI846_REG_UNKNOWN_021E, 0x0235},
+
+ {HI846_REG_ISP_EN_H, 0x016a},
+ {HI846_REG_UNKNOWN_0418, 0x0000},
+ {HI846_REG_UNKNOWN_0B02, 0xe04d},
+ {HI846_REG_UNKNOWN_0B10, 0x6c21},
+ {HI846_REG_UNKNOWN_0B12, 0x0120},
+ {HI846_REG_UNKNOWN_0B14, 0x0005},
+ {HI846_REG_UNKNOWN_2008, 0x38fd},
+ {HI846_REG_UNKNOWN_326E, 0x0000},
+};
+
+static const struct hi846_reg mode_1632x1224_mipi_2lane[] = {
+ {HI846_REG_UNKNOWN_0900, 0x0300},
+ {HI846_REG_MIPI_TX_OP_MODE, 0x4319},
+ {HI846_REG_UNKNOWN_0914, 0xc109},
+ {HI846_REG_TCLK_PREPARE, 0x061a},
+ {HI846_REG_UNKNOWN_0918, 0x0407},
+ {HI846_REG_THS_ZERO, 0x0a0b},
+ {HI846_REG_TCLK_POST, 0x0e08},
+ {HI846_REG_UNKNOWN_091E, 0x0a00},
+ {HI846_REG_UNKNOWN_090C, 0x0427},
+ {HI846_REG_UNKNOWN_090E, 0x0069},
+ {HI846_REG_UNKNOWN_0954, 0x0089},
+ {HI846_REG_UNKNOWN_0956, 0x0000},
+ {HI846_REG_UNKNOWN_0958, 0xca80},
+ {HI846_REG_UNKNOWN_095A, 0x9240},
+ {HI846_REG_PLL_CFG_MIPI2_H, 0x4124},
+ {HI846_REG_TG_ENABLE, 0x0100},
+};
+
+static const struct hi846_reg mode_1632x1224_mipi_4lane[] = {
+ {HI846_REG_UNKNOWN_0900, 0x0300},
+ {HI846_REG_MIPI_TX_OP_MODE, 0xc319},
+ {HI846_REG_UNKNOWN_0914, 0xc105},
+ {HI846_REG_TCLK_PREPARE, 0x030c},
+ {HI846_REG_UNKNOWN_0918, 0x0304},
+ {HI846_REG_THS_ZERO, 0x0708},
+ {HI846_REG_TCLK_POST, 0x0b04},
+ {HI846_REG_UNKNOWN_091E, 0x0500},
+ {HI846_REG_UNKNOWN_090C, 0x0208},
+ {HI846_REG_UNKNOWN_090E, 0x001c},
+ {HI846_REG_UNKNOWN_0954, 0x0089},
+ {HI846_REG_UNKNOWN_0956, 0x0000},
+ {HI846_REG_UNKNOWN_0958, 0xca80},
+ {HI846_REG_UNKNOWN_095A, 0x9240},
+ {HI846_REG_PLL_CFG_MIPI2_H, 0x4924},
+ {HI846_REG_TG_ENABLE, 0x0100},
+};
+
+static const char * const hi846_test_pattern_menu[] = {
+ "Disabled",
+ "Solid Colour",
+ "100% Colour Bars",
+ "Fade To Grey Colour Bars",
+ "PN9",
+ "Gradient Horizontal",
+ "Gradient Vertical",
+ "Check Board",
+ "Slant Pattern",
+ "Resolution Pattern",
+};
+
+#define FREQ_INDEX_640 0
+#define FREQ_INDEX_1280 1
+static const s64 hi846_link_freqs[] = {
+ [FREQ_INDEX_640] = 80000000,
+ [FREQ_INDEX_1280] = 200000000,
+};
+
+static const struct hi846_reg_list hi846_init_regs_list_2lane = {
+ .num_of_regs = ARRAY_SIZE(hi846_init_2lane),
+ .regs = hi846_init_2lane,
+};
+
+static const struct hi846_reg_list hi846_init_regs_list_4lane = {
+ .num_of_regs = ARRAY_SIZE(hi846_init_4lane),
+ .regs = hi846_init_4lane,
+};
+
+static const struct hi846_mode supported_modes[] = {
+ {
+ .width = 640,
+ .height = 480,
+ .link_freq_index = FREQ_INDEX_640,
+ .fps = 120,
+ .frame_len = 631,
+ .llp = HI846_LINE_LENGTH,
+ .reg_list_config = {
+ .num_of_regs = ARRAY_SIZE(mode_640x480_config),
+ .regs = mode_640x480_config,
+ },
+ .reg_list_2lane = {
+ .num_of_regs = ARRAY_SIZE(mode_640x480_mipi_2lane),
+ .regs = mode_640x480_mipi_2lane,
+ },
+ .reg_list_4lane = {
+ .num_of_regs = 0,
+ },
+ .crop = {
+ .left = 0x58,
+ .top = 0x148,
+ .width = 640 * 4,
+ .height = 480 * 4,
+ },
+ },
+ {
+ .width = 1280,
+ .height = 720,
+ .link_freq_index = FREQ_INDEX_1280,
+ .fps = 90,
+ .frame_len = 842,
+ .llp = HI846_LINE_LENGTH,
+ .reg_list_config = {
+ .num_of_regs = ARRAY_SIZE(mode_1280x720_config),
+ .regs = mode_1280x720_config,
+ },
+ .reg_list_2lane = {
+ .num_of_regs = ARRAY_SIZE(mode_1280x720_mipi_2lane),
+ .regs = mode_1280x720_mipi_2lane,
+ },
+ .reg_list_4lane = {
+ .num_of_regs = ARRAY_SIZE(mode_1280x720_mipi_4lane),
+ .regs = mode_1280x720_mipi_4lane,
+ },
+ .crop = {
+ .left = 0xb0,
+ .top = 0x238,
+ .width = 1280 * 2,
+ .height = 720 * 2,
+ },
+ },
+ {
+ .width = 1632,
+ .height = 1224,
+ .link_freq_index = FREQ_INDEX_1280,
+ .fps = 30,
+ .frame_len = 2526,
+ .llp = HI846_LINE_LENGTH,
+ .reg_list_config = {
+ .num_of_regs = ARRAY_SIZE(mode_1632x1224_config),
+ .regs = mode_1632x1224_config,
+ },
+ .reg_list_2lane = {
+ .num_of_regs = ARRAY_SIZE(mode_1632x1224_mipi_2lane),
+ .regs = mode_1632x1224_mipi_2lane,
+ },
+ .reg_list_4lane = {
+ .num_of_regs = ARRAY_SIZE(mode_1632x1224_mipi_4lane),
+ .regs = mode_1632x1224_mipi_4lane,
+ },
+ .crop = {
+ .left = 0x0,
+ .top = 0x0,
+ .width = 1632 * 2,
+ .height = 1224 * 2,
+ },
+ }
+};
+
+struct hi846_datafmt {
+ u32 code;
+ enum v4l2_colorspace colorspace;
+};
+
+static const char * const hi846_supply_names[] = {
+ "vddio", /* Digital I/O (1.8V or 2.8V) */
+ "vdda", /* Analog (2.8V) */
+ "vddd", /* Digital Core (1.2V) */
+};
+
+#define HI846_NUM_SUPPLIES ARRAY_SIZE(hi846_supply_names)
+
+struct hi846 {
+ struct gpio_desc *rst_gpio;
+ struct gpio_desc *shutdown_gpio;
+ struct regulator_bulk_data supplies[HI846_NUM_SUPPLIES];
+ struct clk *clock;
+ const struct hi846_datafmt *fmt;
+ struct v4l2_subdev sd;
+ struct media_pad pad;
+ struct v4l2_ctrl_handler ctrl_handler;
+ u8 nr_lanes;
+
+ struct v4l2_ctrl *link_freq;
+ struct v4l2_ctrl *pixel_rate;
+ struct v4l2_ctrl *vblank;
+ struct v4l2_ctrl *hblank;
+ struct v4l2_ctrl *exposure;
+
+ struct mutex mutex; /* protect cur_mode, streaming and chip access */
+ const struct hi846_mode *cur_mode;
+ bool streaming;
+};
+
+static inline struct hi846 *to_hi846(struct v4l2_subdev *sd)
+{
+ return container_of(sd, struct hi846, sd);
+}
+
+static const struct hi846_datafmt hi846_colour_fmts[] = {
+ { HI846_MEDIA_BUS_FORMAT, V4L2_COLORSPACE_RAW },
+};
+
+static const struct hi846_datafmt *hi846_find_datafmt(u32 code)
+{
+ unsigned int i;
+
+ for (i = 0; i < ARRAY_SIZE(hi846_colour_fmts); i++)
+ if (hi846_colour_fmts[i].code == code)
+ return &hi846_colour_fmts[i];
+
+ return NULL;
+}
+
+static inline u8 hi846_get_link_freq_index(struct hi846 *hi846)
+{
+ return hi846->cur_mode->link_freq_index;
+}
+
+static u64 hi846_get_link_freq(struct hi846 *hi846)
+{
+ u8 index = hi846_get_link_freq_index(hi846);
+
+ return hi846_link_freqs[index];
+}
+
+static u64 hi846_calc_pixel_rate(struct hi846 *hi846)
+{
+ u64 link_freq = hi846_get_link_freq(hi846);
+ u64 pixel_rate = link_freq * 2 * hi846->nr_lanes;
+
+ do_div(pixel_rate, HI846_RGB_DEPTH);
+
+ return pixel_rate;
+}
+
+static int hi846_read_reg(struct hi846 *hi846, u16 reg, u8 *val)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd);
+ struct i2c_msg msgs[2];
+ u8 addr_buf[2];
+ u8 data_buf[1] = {0};
+ int ret;
+
+ put_unaligned_be16(reg, addr_buf);
+ msgs[0].addr = client->addr;
+ msgs[0].flags = 0;
+ msgs[0].len = sizeof(addr_buf);
+ msgs[0].buf = addr_buf;
+ msgs[1].addr = client->addr;
+ msgs[1].flags = I2C_M_RD;
+ msgs[1].len = 1;
+ msgs[1].buf = data_buf;
+
+ ret = i2c_transfer(client->adapter, msgs, ARRAY_SIZE(msgs));
+ if (ret != ARRAY_SIZE(msgs)) {
+ dev_err(&client->dev, "i2c read error: %d\n", ret);
+ return -EIO;
+ }
+
+ *val = data_buf[0];
+
+ return 0;
+}
+
+static int hi846_write_reg(struct hi846 *hi846, u16 reg, u8 val)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd);
+ u8 buf[3] = { reg >> 8, reg & 0xff, val };
+ struct i2c_msg msg[] = {
+ { .addr = client->addr, .flags = 0,
+ .len = ARRAY_SIZE(buf), .buf = buf },
+ };
+ int ret;
+
+ ret = i2c_transfer(client->adapter, msg, ARRAY_SIZE(msg));
+ if (ret != ARRAY_SIZE(msg)) {
+ dev_err(&client->dev, "i2c write error\n");
+ return -EIO;
+ }
+
+ return 0;
+}
+
+static void hi846_write_reg_16(struct hi846 *hi846, u16 reg, u16 val, int *err)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd);
+ u8 buf[4];
+ int ret;
+
+ if (*err < 0)
+ return;
+
+ put_unaligned_be16(reg, buf);
+ put_unaligned_be16(val, buf + 2);
+ ret = i2c_master_send(client, buf, sizeof(buf));
+ if (ret != sizeof(buf)) {
+ dev_err(&client->dev, "i2c_master_send != %zu: %d\n",
+ sizeof(buf), ret);
+ *err = -EIO;
+ }
+}
+
+static int hi846_write_reg_list(struct hi846 *hi846,
+ const struct hi846_reg_list *r_list)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd);
+ unsigned int i;
+ int ret = 0;
+
+ for (i = 0; i < r_list->num_of_regs; i++) {
+ hi846_write_reg_16(hi846, r_list->regs[i].address,
+ r_list->regs[i].val, &ret);
+ if (ret) {
+ dev_err_ratelimited(&client->dev,
+ "failed to write reg 0x%4.4x: %d",
+ r_list->regs[i].address, ret);
+ return ret;
+ }
+ }
+
+ return 0;
+}
+
+static int hi846_update_digital_gain(struct hi846 *hi846, u16 d_gain)
+{
+ int ret = 0;
+
+ hi846_write_reg_16(hi846, HI846_REG_MWB_GR_GAIN_H, d_gain, &ret);
+ hi846_write_reg_16(hi846, HI846_REG_MWB_GB_GAIN_H, d_gain, &ret);
+ hi846_write_reg_16(hi846, HI846_REG_MWB_R_GAIN_H, d_gain, &ret);
+ hi846_write_reg_16(hi846, HI846_REG_MWB_B_GAIN_H, d_gain, &ret);
+
+ return ret;
+}
+
+static int hi846_test_pattern(struct hi846 *hi846, u32 pattern)
+{
+ int ret;
+ u8 val;
+
+ if (pattern) {
+ ret = hi846_read_reg(hi846, HI846_REG_ISP, &val);
+ if (ret)
+ return ret;
+
+ ret = hi846_write_reg(hi846, HI846_REG_ISP,
+ val | HI846_REG_ISP_TPG_EN);
+ if (ret)
+ return ret;
+ }
+
+ return hi846_write_reg(hi846, HI846_REG_TEST_PATTERN, pattern);
+}
+
+static int hi846_set_ctrl(struct v4l2_ctrl *ctrl)
+{
+ struct hi846 *hi846 = container_of(ctrl->handler,
+ struct hi846, ctrl_handler);
+ struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd);
+ s64 exposure_max;
+ int ret = 0;
+ u32 shutter, frame_len;
+
+ /* Propagate change of current control to all related controls */
+ if (ctrl->id == V4L2_CID_VBLANK) {
+ /* Update max exposure while meeting expected vblanking */
+ exposure_max = hi846->cur_mode->height + ctrl->val -
+ HI846_EXPOSURE_MAX_MARGIN;
+ __v4l2_ctrl_modify_range(hi846->exposure,
+ hi846->exposure->minimum,
+ exposure_max, hi846->exposure->step,
+ exposure_max);
+ }
+
+ if (!pm_runtime_get_if_in_use(&client->dev))
+ return 0;
+
+ switch (ctrl->id) {
+ case V4L2_CID_ANALOGUE_GAIN:
+ ret = hi846_write_reg(hi846, HI846_REG_ANALOG_GAIN, ctrl->val);
+ break;
+
+ case V4L2_CID_DIGITAL_GAIN:
+ ret = hi846_update_digital_gain(hi846, ctrl->val);
+ break;
+
+ case V4L2_CID_EXPOSURE:
+ shutter = ctrl->val;
+ frame_len = hi846->cur_mode->frame_len;
+
+ if (shutter > frame_len - 6) { /* margin */
+ frame_len = shutter + 6;
+ if (frame_len > 0xffff) { /* max frame len */
+ frame_len = 0xffff;
+ }
+ }
+
+ if (shutter < 6)
+ shutter = 6;
+ if (shutter > (0xffff - 6))
+ shutter = 0xffff - 6;
+
+ hi846_write_reg_16(hi846, HI846_REG_FLL, frame_len, &ret);
+ hi846_write_reg_16(hi846, HI846_REG_EXPOSURE, shutter, &ret);
+ break;
+
+ case V4L2_CID_VBLANK:
+ /* Update FLL that meets expected vertical blanking */
+ hi846_write_reg_16(hi846, HI846_REG_FLL,
+ hi846->cur_mode->height + ctrl->val, &ret);
+ break;
+ case V4L2_CID_TEST_PATTERN:
+ ret = hi846_test_pattern(hi846, ctrl->val);
+ break;
+
+ default:
+ ret = -EINVAL;
+ break;
+ }
+
+ pm_runtime_put(&client->dev);
+
+ return ret;
+}
+
+static const struct v4l2_ctrl_ops hi846_ctrl_ops = {
+ .s_ctrl = hi846_set_ctrl,
+};
+
+static int hi846_init_controls(struct hi846 *hi846)
+{
+ struct v4l2_ctrl_handler *ctrl_hdlr;
+ s64 exposure_max, h_blank;
+ int ret;
+ struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd);
+ struct v4l2_fwnode_device_properties props;
+
+ ctrl_hdlr = &hi846->ctrl_handler;
+ ret = v4l2_ctrl_handler_init(ctrl_hdlr, 10);
+ if (ret)
+ return ret;
+
+ ctrl_hdlr->lock = &hi846->mutex;
+
+ hi846->link_freq =
+ v4l2_ctrl_new_int_menu(ctrl_hdlr, &hi846_ctrl_ops,
+ V4L2_CID_LINK_FREQ,
+ ARRAY_SIZE(hi846_link_freqs) - 1,
+ 0, hi846_link_freqs);
+ if (hi846->link_freq)
+ hi846->link_freq->flags |= V4L2_CTRL_FLAG_READ_ONLY;
+
+ hi846->pixel_rate =
+ v4l2_ctrl_new_std(ctrl_hdlr, &hi846_ctrl_ops,
+ V4L2_CID_PIXEL_RATE, 0,
+ hi846_calc_pixel_rate(hi846), 1,
+ hi846_calc_pixel_rate(hi846));
+ hi846->vblank = v4l2_ctrl_new_std(ctrl_hdlr, &hi846_ctrl_ops,
+ V4L2_CID_VBLANK,
+ hi846->cur_mode->frame_len -
+ hi846->cur_mode->height,
+ HI846_FLL_MAX -
+ hi846->cur_mode->height, 1,
+ hi846->cur_mode->frame_len -
+ hi846->cur_mode->height);
+
+ h_blank = hi846->cur_mode->llp - hi846->cur_mode->width;
+
+ hi846->hblank = v4l2_ctrl_new_std(ctrl_hdlr, &hi846_ctrl_ops,
+ V4L2_CID_HBLANK, h_blank, h_blank, 1,
+ h_blank);
+ if (hi846->hblank)
+ hi846->hblank->flags |= V4L2_CTRL_FLAG_READ_ONLY;
+
+ v4l2_ctrl_new_std(ctrl_hdlr, &hi846_ctrl_ops, V4L2_CID_ANALOGUE_GAIN,
+ HI846_ANAL_GAIN_MIN, HI846_ANAL_GAIN_MAX,
+ HI846_ANAL_GAIN_STEP, HI846_ANAL_GAIN_MIN);
+ v4l2_ctrl_new_std(ctrl_hdlr, &hi846_ctrl_ops, V4L2_CID_DIGITAL_GAIN,
+ HI846_DGTL_GAIN_MIN, HI846_DGTL_GAIN_MAX,
+ HI846_DGTL_GAIN_STEP, HI846_DGTL_GAIN_DEFAULT);
+ exposure_max = hi846->cur_mode->frame_len - HI846_EXPOSURE_MAX_MARGIN;
+ hi846->exposure = v4l2_ctrl_new_std(ctrl_hdlr, &hi846_ctrl_ops,
+ V4L2_CID_EXPOSURE,
+ HI846_EXPOSURE_MIN, exposure_max,
+ HI846_EXPOSURE_STEP,
+ exposure_max);
+ v4l2_ctrl_new_std_menu_items(ctrl_hdlr, &hi846_ctrl_ops,
+ V4L2_CID_TEST_PATTERN,
+ ARRAY_SIZE(hi846_test_pattern_menu) - 1,
+ 0, 0, hi846_test_pattern_menu);
+ if (ctrl_hdlr->error) {
+ dev_err(&client->dev, "v4l ctrl handler error: %d\n",
+ ctrl_hdlr->error);
+ return ctrl_hdlr->error;
+ }
+
+ ret = v4l2_fwnode_device_parse(&client->dev, &props);
+ if (ret)
+ return ret;
+
+ ret = v4l2_ctrl_new_fwnode_properties(ctrl_hdlr, &hi846_ctrl_ops,
+ &props);
+ if (ret)
+ return ret;
+
+ hi846->sd.ctrl_handler = ctrl_hdlr;
+
+ return 0;
+}
+
+static int hi846_set_video_mode(struct hi846 *hi846, int fps)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd);
+ u64 frame_length;
+ int ret = 0;
+ int dummy_lines;
+ u64 link_freq = hi846_get_link_freq(hi846);
+
+ dev_dbg(&client->dev, "%s: link freq: %llu\n", __func__,
+ hi846_get_link_freq(hi846));
+
+ do_div(link_freq, fps);
+ frame_length = link_freq;
+ do_div(frame_length, HI846_LINE_LENGTH);
+
+ dummy_lines = (frame_length > hi846->cur_mode->frame_len) ?
+ (frame_length - hi846->cur_mode->frame_len) : 0;
+
+ frame_length = hi846->cur_mode->frame_len + dummy_lines;
+
+ dev_dbg(&client->dev, "%s: frame length calculated: %llu\n", __func__,
+ frame_length);
+
+ hi846_write_reg_16(hi846, HI846_REG_FLL, frame_length & 0xFFFF, &ret);
+ hi846_write_reg_16(hi846, HI846_REG_LLP,
+ HI846_LINE_LENGTH & 0xFFFF, &ret);
+
+ return ret;
+}
+
+static int hi846_start_streaming(struct hi846 *hi846)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd);
+ int ret = 0;
+ u8 val;
+
+ if (hi846->nr_lanes == 2)
+ ret = hi846_write_reg_list(hi846, &hi846_init_regs_list_2lane);
+ else
+ ret = hi846_write_reg_list(hi846, &hi846_init_regs_list_4lane);
+ if (ret) {
+ dev_err(&client->dev, "failed to set plls: %d\n", ret);
+ return ret;
+ }
+
+ ret = hi846_write_reg_list(hi846, &hi846->cur_mode->reg_list_config);
+ if (ret) {
+ dev_err(&client->dev, "failed to set mode: %d\n", ret);
+ return ret;
+ }
+
+ if (hi846->nr_lanes == 2)
+ ret = hi846_write_reg_list(hi846,
+ &hi846->cur_mode->reg_list_2lane);
+ else
+ ret = hi846_write_reg_list(hi846,
+ &hi846->cur_mode->reg_list_4lane);
+ if (ret) {
+ dev_err(&client->dev, "failed to set mipi mode: %d\n", ret);
+ return ret;
+ }
+
+ hi846_set_video_mode(hi846, hi846->cur_mode->fps);
+
+ ret = __v4l2_ctrl_handler_setup(hi846->sd.ctrl_handler);
+ if (ret)
+ return ret;
+
+ /*
+ * Reading 0x0034 is purely done for debugging reasons: It is not
+ * documented in the DS but only mentioned once:
+ * "If 0x0034[2] bit is disabled , Visible pixel width and height is 0."
+ * So even though that sounds like we won't see anything, we don't
+ * know more about this, so in that case only inform the user but do
+ * nothing more.
+ */
+ ret = hi846_read_reg(hi846, 0x0034, &val);
+ if (ret)
+ return ret;
+ if (!(val & BIT(2)))
+ dev_info(&client->dev, "visible pixel width and height is 0\n");
+
+ ret = hi846_write_reg(hi846, HI846_REG_MODE_SELECT,
+ HI846_MODE_STREAMING);
+ if (ret) {
+ dev_err(&client->dev, "failed to start stream");
+ return ret;
+ }
+
+ hi846->streaming = 1;
+
+ dev_dbg(&client->dev, "%s: started streaming successfully\n", __func__);
+
+ return ret;
+}
+
+static void hi846_stop_streaming(struct hi846 *hi846)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd);
+
+ if (hi846_write_reg(hi846, HI846_REG_MODE_SELECT, HI846_MODE_STANDBY))
+ dev_err(&client->dev, "failed to stop stream");
+
+ hi846->streaming = 0;
+}
+
+static int hi846_set_stream(struct v4l2_subdev *sd, int enable)
+{
+ struct hi846 *hi846 = to_hi846(sd);
+ struct i2c_client *client = v4l2_get_subdevdata(sd);
+ int ret = 0;
+
+ if (hi846->streaming == enable)
+ return 0;
+
+ mutex_lock(&hi846->mutex);
+
+ if (enable) {
+ ret = pm_runtime_get_sync(&client->dev);
+ if (ret < 0) {
+ pm_runtime_put_noidle(&client->dev);
+ goto out;
+ }
+
+ ret = hi846_start_streaming(hi846);
+ }
+
+ if (!enable || ret) {
+ hi846_stop_streaming(hi846);
+ pm_runtime_put(&client->dev);
+ }
+
+out:
+ mutex_unlock(&hi846->mutex);
+
+ return ret;
+}
+
+static int hi846_power_on(struct hi846 *hi846)
+{
+ int ret;
+
+ ret = regulator_bulk_enable(HI846_NUM_SUPPLIES, hi846->supplies);
+ if (ret < 0)
+ return ret;
+
+ ret = clk_prepare_enable(hi846->clock);
+ if (ret < 0)
+ goto err_reg;
+
+ if (hi846->shutdown_gpio)
+ gpiod_set_value_cansleep(hi846->shutdown_gpio, 0);
+
+ /* 30us = 2400 cycles at 80Mhz */
+ usleep_range(30, 60);
+ if (hi846->rst_gpio)
+ gpiod_set_value_cansleep(hi846->rst_gpio, 0);
+ usleep_range(30, 60);
+
+ return 0;
+
+err_reg:
+ regulator_bulk_disable(HI846_NUM_SUPPLIES, hi846->supplies);
+
+ return ret;
+}
+
+static void hi846_power_off(struct hi846 *hi846)
+{
+ if (hi846->rst_gpio)
+ gpiod_set_value_cansleep(hi846->rst_gpio, 1);
+
+ if (hi846->shutdown_gpio)
+ gpiod_set_value_cansleep(hi846->shutdown_gpio, 1);
+
+ clk_disable_unprepare(hi846->clock);
+ regulator_bulk_disable(HI846_NUM_SUPPLIES, hi846->supplies);
+}
+
+static int __maybe_unused hi846_suspend(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct v4l2_subdev *sd = i2c_get_clientdata(client);
+ struct hi846 *hi846 = to_hi846(sd);
+
+ if (hi846->streaming)
+ hi846_stop_streaming(hi846);
+
+ hi846_power_off(hi846);
+
+ return 0;
+}
+
+static int __maybe_unused hi846_resume(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct v4l2_subdev *sd = i2c_get_clientdata(client);
+ struct hi846 *hi846 = to_hi846(sd);
+ int ret;
+
+ ret = hi846_power_on(hi846);
+ if (ret)
+ return ret;
+
+ if (hi846->streaming) {
+ ret = hi846_start_streaming(hi846);
+ if (ret) {
+ dev_err(dev, "%s: start streaming failed: %d\n",
+ __func__, ret);
+ goto error;
+ }
+ }
+
+ return 0;
+
+error:
+ hi846_power_off(hi846);
+ return ret;
+}
+
+static int hi846_set_format(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *sd_state,
+ struct v4l2_subdev_format *format)
+{
+ struct hi846 *hi846 = to_hi846(sd);
+ struct v4l2_mbus_framefmt *mf = &format->format;
+ struct i2c_client *client = v4l2_get_subdevdata(sd);
+ const struct hi846_datafmt *fmt = hi846_find_datafmt(mf->code);
+ u32 tgt_fps;
+ s32 vblank_def, h_blank;
+
+ if (!fmt) {
+ mf->code = hi846_colour_fmts[0].code;
+ mf->colorspace = hi846_colour_fmts[0].colorspace;
+ fmt = &hi846_colour_fmts[0];
+ }
+
+ if (format->which == V4L2_SUBDEV_FORMAT_TRY) {
+ *v4l2_subdev_get_try_format(sd, sd_state, format->pad) = *mf;
+ return 0;
+ }
+
+ if (hi846->nr_lanes == 2) {
+ if (!hi846->cur_mode->reg_list_2lane.num_of_regs) {
+ dev_err(&client->dev,
+ "this mode is not supported for 2 lanes\n");
+ return -EINVAL;
+ }
+ } else {
+ if (!hi846->cur_mode->reg_list_4lane.num_of_regs) {
+ dev_err(&client->dev,
+ "this mode is not supported for 4 lanes\n");
+ return -EINVAL;
+ }
+ }
+
+ mutex_lock(&hi846->mutex);
+
+ if (hi846->streaming) {
+ mutex_unlock(&hi846->mutex);
+ return -EBUSY;
+ }
+
+ hi846->fmt = fmt;
+
+ hi846->cur_mode =
+ v4l2_find_nearest_size(supported_modes,
+ ARRAY_SIZE(supported_modes),
+ width, height, mf->width, mf->height);
+ dev_dbg(&client->dev, "%s: found mode: %dx%d\n", __func__,
+ hi846->cur_mode->width, hi846->cur_mode->height);
+
+ tgt_fps = hi846->cur_mode->fps;
+ dev_dbg(&client->dev, "%s: target fps: %d\n", __func__, tgt_fps);
+
+ mf->width = hi846->cur_mode->width;
+ mf->height = hi846->cur_mode->height;
+ mf->code = HI846_MEDIA_BUS_FORMAT;
+ mf->field = V4L2_FIELD_NONE;
+
+ __v4l2_ctrl_s_ctrl(hi846->link_freq, hi846_get_link_freq_index(hi846));
+ __v4l2_ctrl_s_ctrl_int64(hi846->pixel_rate,
+ hi846_calc_pixel_rate(hi846));
+
+ /* Update limits and set FPS to default */
+ vblank_def = hi846->cur_mode->frame_len - hi846->cur_mode->height;
+ __v4l2_ctrl_modify_range(hi846->vblank,
+ hi846->cur_mode->frame_len -
+ hi846->cur_mode->height,
+ HI846_FLL_MAX - hi846->cur_mode->height, 1,
+ vblank_def);
+ __v4l2_ctrl_s_ctrl(hi846->vblank, vblank_def);
+
+ h_blank = hi846->cur_mode->llp - hi846->cur_mode->width;
+
+ __v4l2_ctrl_modify_range(hi846->hblank, h_blank, h_blank, 1,
+ h_blank);
+
+ dev_dbg(&client->dev, "Set fmt w=%d h=%d code=0x%x colorspace=0x%x\n",
+ mf->width, mf->height,
+ fmt->code, fmt->colorspace);
+
+ mutex_unlock(&hi846->mutex);
+
+ return 0;
+}
+
+static int hi846_get_format(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *sd_state,
+ struct v4l2_subdev_format *format)
+{
+ struct hi846 *hi846 = to_hi846(sd);
+ struct v4l2_mbus_framefmt *mf = &format->format;
+ struct i2c_client *client = v4l2_get_subdevdata(sd);
+
+ if (format->which == V4L2_SUBDEV_FORMAT_TRY) {
+ format->format = *v4l2_subdev_get_try_format(&hi846->sd,
+ sd_state,
+ format->pad);
+ return 0;
+ }
+
+ mutex_lock(&hi846->mutex);
+ mf->code = HI846_MEDIA_BUS_FORMAT;
+ mf->colorspace = V4L2_COLORSPACE_RAW;
+ mf->field = V4L2_FIELD_NONE;
+ mf->width = hi846->cur_mode->width;
+ mf->height = hi846->cur_mode->height;
+ mutex_unlock(&hi846->mutex);
+ dev_dbg(&client->dev,
+ "Get format w=%d h=%d code=0x%x colorspace=0x%x\n",
+ mf->width, mf->height, mf->code, mf->colorspace);
+
+ return 0;
+}
+
+static int hi846_enum_mbus_code(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *sd_state,
+ struct v4l2_subdev_mbus_code_enum *code)
+{
+ if (code->pad || code->index > 0)
+ return -EINVAL;
+
+ code->code = HI846_MEDIA_BUS_FORMAT;
+
+ return 0;
+}
+
+static int hi846_enum_frame_size(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *sd_state,
+ struct v4l2_subdev_frame_size_enum *fse)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(sd);
+
+ if (fse->pad || fse->index >= ARRAY_SIZE(supported_modes))
+ return -EINVAL;
+
+ if (fse->code != HI846_MEDIA_BUS_FORMAT) {
+ dev_err(&client->dev, "frame size enum not matching\n");
+ return -EINVAL;
+ }
+
+ fse->min_width = supported_modes[fse->index].width;
+ fse->max_width = supported_modes[fse->index].width;
+ fse->min_height = supported_modes[fse->index].height;
+ fse->max_height = supported_modes[fse->index].height;
+
+ dev_dbg(&client->dev, "%s: max width: %d max height: %d\n", __func__,
+ fse->max_width, fse->max_height);
+
+ return 0;
+}
+
+static int hi846_get_selection(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *sd_state,
+ struct v4l2_subdev_selection *sel)
+{
+ struct hi846 *hi846 = to_hi846(sd);
+
+ switch (sel->target) {
+ case V4L2_SEL_TGT_CROP:
+ case V4L2_SEL_TGT_CROP_DEFAULT:
+ mutex_lock(&hi846->mutex);
+ switch (sel->which) {
+ case V4L2_SUBDEV_FORMAT_TRY:
+ v4l2_subdev_get_try_crop(sd, sd_state, sel->pad);
+ break;
+ case V4L2_SUBDEV_FORMAT_ACTIVE:
+ sel->r = hi846->cur_mode->crop;
+ break;
+ }
+ mutex_unlock(&hi846->mutex);
+ return 0;
+ case V4L2_SEL_TGT_CROP_BOUNDS:
+ case V4L2_SEL_TGT_NATIVE_SIZE:
+ sel->r.top = 0;
+ sel->r.left = 0;
+ sel->r.width = 3264;
+ sel->r.height = 2448;
+ return 0;
+ default:
+ return -EINVAL;
+ }
+}
+
+static int hi846_init_cfg(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *sd_state)
+{
+ struct hi846 *hi846 = to_hi846(sd);
+ struct v4l2_mbus_framefmt *mf;
+
+ mf = v4l2_subdev_get_try_format(sd, sd_state, 0);
+
+ mutex_lock(&hi846->mutex);
+ mf->code = HI846_MEDIA_BUS_FORMAT;
+ mf->colorspace = V4L2_COLORSPACE_RAW;
+ mf->field = V4L2_FIELD_NONE;
+ mf->width = hi846->cur_mode->width;
+ mf->height = hi846->cur_mode->height;
+ mutex_unlock(&hi846->mutex);
+
+ return 0;
+}
+
+static const struct v4l2_subdev_video_ops hi846_video_ops = {
+ .s_stream = hi846_set_stream,
+};
+
+static const struct v4l2_subdev_pad_ops hi846_pad_ops = {
+ .init_cfg = hi846_init_cfg,
+ .enum_frame_size = hi846_enum_frame_size,
+ .enum_mbus_code = hi846_enum_mbus_code,
+ .set_fmt = hi846_set_format,
+ .get_fmt = hi846_get_format,
+ .get_selection = hi846_get_selection,
+};
+
+static const struct v4l2_subdev_ops hi846_subdev_ops = {
+ .video = &hi846_video_ops,
+ .pad = &hi846_pad_ops,
+};
+
+static const struct media_entity_operations hi846_subdev_entity_ops = {
+ .link_validate = v4l2_subdev_link_validate,
+};
+
+static int hi846_identify_module(struct hi846 *hi846)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd);
+ int ret;
+ u8 hi, lo;
+
+ ret = hi846_read_reg(hi846, HI846_REG_CHIP_ID_L, &lo);
+ if (ret)
+ return ret;
+
+ if (lo != HI846_CHIP_ID_L) {
+ dev_err(&client->dev, "wrong chip id low byte: %x", lo);
+ return -ENXIO;
+ }
+
+ ret = hi846_read_reg(hi846, HI846_REG_CHIP_ID_H, &hi);
+ if (ret)
+ return ret;
+
+ if (hi != HI846_CHIP_ID_H) {
+ dev_err(&client->dev, "wrong chip id high byte: %x", hi);
+ return -ENXIO;
+ }
+
+ dev_info(&client->dev, "chip id %02X %02X using %d mipi lanes\n",
+ hi, lo, hi846->nr_lanes);
+
+ return 0;
+}
+
+static s64 hi846_check_link_freqs(struct hi846 *hi846,
+ struct v4l2_fwnode_endpoint *ep)
+{
+ const s64 *freqs = hi846_link_freqs;
+ int freqs_count = ARRAY_SIZE(hi846_link_freqs);
+ int i, j;
+
+ for (i = 0; i < freqs_count; i++) {
+ for (j = 0; j < ep->nr_of_link_frequencies; j++)
+ if (freqs[i] == ep->link_frequencies[j])
+ break;
+ if (j == ep->nr_of_link_frequencies)
+ return freqs[i];
+ }
+
+ return 0;
+}
+
+static int hi846_parse_dt(struct hi846 *hi846, struct device *dev)
+{
+ struct fwnode_handle *ep;
+ struct fwnode_handle *fwnode = dev_fwnode(dev);
+ struct v4l2_fwnode_endpoint bus_cfg = {
+ .bus_type = V4L2_MBUS_CSI2_DPHY
+ };
+ int ret;
+ s64 fq;
+
+ ep = fwnode_graph_get_next_endpoint(fwnode, NULL);
+ if (!ep) {
+ dev_err(dev, "unable to find endpoint node\n");
+ return -ENXIO;
+ }
+
+ ret = v4l2_fwnode_endpoint_alloc_parse(ep, &bus_cfg);
+ fwnode_handle_put(ep);
+ if (ret) {
+ dev_err(dev, "failed to parse endpoint node: %d\n", ret);
+ return ret;
+ }
+
+ if (bus_cfg.bus.mipi_csi2.num_data_lanes != 2 &&
+ bus_cfg.bus.mipi_csi2.num_data_lanes != 4) {
+ dev_err(dev, "number of CSI2 data lanes %d is not supported",
+ bus_cfg.bus.mipi_csi2.num_data_lanes);
+ v4l2_fwnode_endpoint_free(&bus_cfg);
+ return -EINVAL;
+ }
+
+ hi846->nr_lanes = bus_cfg.bus.mipi_csi2.num_data_lanes;
+
+ if (!bus_cfg.nr_of_link_frequencies) {
+ dev_err(dev, "link-frequency property not found in DT\n");
+ return -EINVAL;
+ }
+
+ /* Check that link frequences for all the modes are in device tree */
+ fq = hi846_check_link_freqs(hi846, &bus_cfg);
+ if (fq) {
+ dev_err(dev, "Link frequency of %lld is not supported\n", fq);
+ return -EINVAL;
+ }
+
+ v4l2_fwnode_endpoint_free(&bus_cfg);
+
+ hi846->rst_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
+ if (IS_ERR(hi846->rst_gpio)) {
+ dev_err(dev, "failed to get reset gpio: %pe\n",
+ hi846->rst_gpio);
+ return PTR_ERR(hi846->rst_gpio);
+ }
+
+ hi846->shutdown_gpio = devm_gpiod_get_optional(dev, "shutdown",
+ GPIOD_OUT_LOW);
+ if (IS_ERR(hi846->shutdown_gpio)) {
+ dev_err(dev, "failed to get shutdown gpio: %pe\n",
+ hi846->shutdown_gpio);
+ return PTR_ERR(hi846->shutdown_gpio);
+ }
+
+ return 0;
+}
+
+static int hi846_probe(struct i2c_client *client)
+{
+ struct hi846 *hi846;
+ int ret;
+ int i;
+ u32 mclk_freq;
+
+ hi846 = devm_kzalloc(&client->dev, sizeof(*hi846), GFP_KERNEL);
+ if (!hi846)
+ return -ENOMEM;
+
+ ret = hi846_parse_dt(hi846, &client->dev);
+ if (ret) {
+ dev_err(&client->dev, "failed to check HW configuration: %d",
+ ret);
+ return ret;
+ }
+
+ hi846->clock = devm_clk_get(&client->dev, NULL);
+ if (IS_ERR(hi846->clock)) {
+ dev_err(&client->dev, "failed to get clock: %pe\n",
+ hi846->clock);
+ return PTR_ERR(hi846->clock);
+ }
+
+ mclk_freq = clk_get_rate(hi846->clock);
+ if (mclk_freq != 25000000)
+ dev_warn(&client->dev,
+ "External clock freq should be 25000000, not %u.\n",
+ mclk_freq);
+
+ for (i = 0; i < HI846_NUM_SUPPLIES; i++)
+ hi846->supplies[i].supply = hi846_supply_names[i];
+
+ ret = devm_regulator_bulk_get(&client->dev, HI846_NUM_SUPPLIES,
+ hi846->supplies);
+ if (ret < 0)
+ return ret;
+
+ v4l2_i2c_subdev_init(&hi846->sd, client, &hi846_subdev_ops);
+
+ mutex_init(&hi846->mutex);
+
+ ret = hi846_power_on(hi846);
+ if (ret)
+ goto err_mutex;
+
+ ret = hi846_identify_module(hi846);
+ if (ret)
+ goto err_power_off;
+
+ hi846->cur_mode = &supported_modes[0];
+
+ ret = hi846_init_controls(hi846);
+ if (ret) {
+ dev_err(&client->dev, "failed to init controls: %d", ret);
+ goto err_power_off;
+ }
+
+ hi846->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+ hi846->sd.entity.ops = &hi846_subdev_entity_ops;
+ hi846->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR;
+ hi846->pad.flags = MEDIA_PAD_FL_SOURCE;
+ ret = media_entity_pads_init(&hi846->sd.entity, 1, &hi846->pad);
+ if (ret) {
+ dev_err(&client->dev, "failed to init entity pads: %d", ret);
+ goto err_v4l2_ctrl_handler_free;
+ }
+
+ ret = v4l2_async_register_subdev_sensor(&hi846->sd);
+ if (ret < 0) {
+ dev_err(&client->dev, "failed to register V4L2 subdev: %d",
+ ret);
+ goto err_media_entity_cleanup;
+ }
+
+ pm_runtime_set_active(&client->dev);
+ pm_runtime_enable(&client->dev);
+ pm_runtime_idle(&client->dev);
+
+ return 0;
+
+err_media_entity_cleanup:
+ media_entity_cleanup(&hi846->sd.entity);
+
+err_v4l2_ctrl_handler_free:
+ v4l2_ctrl_handler_free(hi846->sd.ctrl_handler);
+
+err_power_off:
+ hi846_power_off(hi846);
+
+err_mutex:
+ mutex_destroy(&hi846->mutex);
+
+ return ret;
+}
+
+static int hi846_remove(struct i2c_client *client)
+{
+ struct v4l2_subdev *sd = i2c_get_clientdata(client);
+ struct hi846 *hi846 = to_hi846(sd);
+
+ v4l2_async_unregister_subdev(sd);
+ media_entity_cleanup(&sd->entity);
+ v4l2_ctrl_handler_free(sd->ctrl_handler);
+
+ pm_runtime_disable(&client->dev);
+ if (!pm_runtime_status_suspended(&client->dev))
+ hi846_suspend(&client->dev);
+ pm_runtime_set_suspended(&client->dev);
+
+ mutex_destroy(&hi846->mutex);
+
+ return 0;
+}
+
+static UNIVERSAL_DEV_PM_OPS(hi846_pm_ops, hi846_suspend, hi846_resume, NULL);
+
+static const struct of_device_id hi846_of_match[] = {
+ { .compatible = "hynix,hi846", },
+ {},
+};
+MODULE_DEVICE_TABLE(of, hi846_of_match);
+
+static struct i2c_driver hi846_i2c_driver = {
+ .driver = {
+ .name = "hi846",
+ .pm = &hi846_pm_ops,
+ .of_match_table = of_match_ptr(hi846_of_match),
+ },
+ .probe_new = hi846_probe,
+ .remove = hi846_remove,
+};
+
+module_i2c_driver(hi846_i2c_driver);
+
+MODULE_AUTHOR("Angus Ainslie <[email protected]>");
+MODULE_AUTHOR("Martin Kepplinger <[email protected]>");
+MODULE_DESCRIPTION("Hynix HI846 sensor driver");
+MODULE_LICENSE("GPL v2");
--
2.30.2
Am Montag, dem 06.09.2021 um 12:28 +0200 schrieb Martin Kepplinger:
> hi,
>
> This series adds support for the SK Hynix Hi-846 CMOS images sensor.
> It includes the dt-bindings and the driver.
>
> best wishes,
>
> martin
hi all, are there any objections, doubts or other thoughts about this
that would prevent it from being merged?
thanks for all the good review,
martin
>
> revision history
> ----------------
> v9: (thank you Pavel and Sakari)
> * fix the probe() error paths (that I broke in v8)
> * cheanups
>
> v8: (thank you Laurent)
> * add fwnode properties support for orientation and rotation on the
> board
> * remove the arm64 defconfig addition patch. deal with that later.
> *
> https://lore.kernel.org/linux-media/[email protected]/
>
> v7: (thank you Sakari)
> * move the check for supported nr_lanes for a mode to set_format()
> * change get_selection() according to the Sakaris' review
> * check for the mipi link frequencies from DT
> * check for the external clock rate and add assigned-clock-rates
> requirement
> *
> https://lore.kernel.org/linux-media/[email protected]/
>
> v6:
> * better digital gain defaults
> * lane config fix found by smatch
> * fix regulator usage in power_on()
> *
> https://lore.kernel.org/linux-media/[email protected]/
>
> v5: (thank you Laurent and Rob)
> * minor dt-bindings fixes
> * driver: disable lens shading correcting (no seed values yet used
> from "otp" for that)
> * add reviewed-tags
> *
> https://lore.kernel.org/linux-media/[email protected]/
>
> v4: (thank you Laurent, Sakari and Rob) many driver changes, see v3
> review for
> details. they include:
> * add get_selection(), remove open() callback
> * use gpiod API
> * use regulator_bulk API
> * fix power supply timing sequence and bindings
> *
> https://lore.kernel.org/linux-media/[email protected]/
>
> v3: (thank you, Laurent)
> * use do_div() for divisions
> * reset-gpios DT property name instead of rst-gpios
> * improve the dt-bindings
> * add the phone-devel list
> *
> https://lore.kernel.org/linux-media/[email protected]/
>
> v2:
> sent a bit early due to stupid mistakes
> * fix build issues
> * fix dtschema issues
> * add enable for arm64 defconfig
> *
> https://lore.kernel.org/linux-media/[email protected]/T/#t
>
> v1:
> *
> https://lore.kernel.org/linux-media/[email protected]/
>
>
> Martin Kepplinger (4):
> dt-bindings: vendor-prefixes: Add SK Hynix Inc.
> dt-bindings: media: document SK Hynix Hi-846 MIPI CSI-2 8M pixel
> sensor
> media: i2c: add driver for the SK Hynix Hi-846 8M pixel camera
> Documentation: i2c-cardlist: add the Hynix hi846 sensor
>
> .../admin-guide/media/i2c-cardlist.rst | 1 +
> .../bindings/media/i2c/hynix,hi846.yaml | 120 +
> .../devicetree/bindings/vendor-prefixes.yaml | 2 +
> MAINTAINERS | 6 +
> drivers/media/i2c/Kconfig | 13 +
> drivers/media/i2c/Makefile | 1 +
> drivers/media/i2c/hi846.c | 2190
> +++++++++++++++++
> 7 files changed, 2333 insertions(+)
> create mode 100644
> Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> create mode 100644 drivers/media/i2c/hi846.c
>
On Mon, Sep 6, 2021 at 12:30 PM Martin Kepplinger
<[email protected]> wrote:
> Document the bindings used for the SK Hynix Hi-846 CMOS camera driver.
>
> Signed-off-by: Martin Kepplinger <[email protected]>
> Reviewed-by: Laurent Pinchart <[email protected]>
> Reviewed-by: Rob Herring <[email protected]>
> ---
> .../bindings/media/i2c/hynix,hi846.yaml | 120 ++++++++++++++++++
> 1 file changed, 120 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
>
> diff --git a/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> new file mode 100644
> index 000000000000..85a8877c2f38
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> @@ -0,0 +1,120 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/media/i2c/hynix,hi846.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: SK Hynix Hi-846 1/4" 8M Pixel MIPI CSI-2 sensor
> +
> +maintainers:
> + - Martin Kepplinger <[email protected]>
> +
> +description: |-
> + The Hi-846 is a raw image sensor with an MIPI CSI-2 image data
> + interface and CCI (I2C compatible) control bus. The output format
> + is raw Bayer.
> +
> +properties:
> + compatible:
> + const: hynix,hi846
> +
> + reg:
> + maxItems: 1
> +
> + clocks:
> + items:
> + - description: Reference to the mclk clock.
> +
> + assigned-clocks:
> + maxItems: 1
> +
> + assigned-clock-rates:
> + maxItems: 1
> +
> + reset-gpios:
> + description: Reference to the GPIO connected to the RESETB pin. Active low.
> + maxItems: 1
> +
> + shutdown-gpios:
> + description: Reference to the GPIO connected to the XSHUTDOWN pin. Active low.
> + maxItems: 1
> +
> + vddio-supply:
> + description: Definition of the regulator used for the VDDIO power supply.
> +
> + vdda-supply:
> + description: Definition of the regulator used for the VDDA power supply.
> +
> + vddd-supply:
> + description: Definition of the regulator used for the VDDD power supply.
> +
> + port:
> + $ref: /schemas/graph.yaml#/properties/port
> +
> + properties:
> + endpoint:
> + $ref: /schemas/media/video-interfaces.yaml#
> + unevaluatedProperties: false
> +
> + properties:
> + data-lanes:
> + oneOf:
> + - items:
> + - const: 1
> + - const: 2
> + - const: 3
> + - const: 4
> + - items:
> + - const: 1
> + - const: 2
> +
> + required:
> + - data-lanes
> +
> +required:
> + - compatible
> + - reg
> + - clocks
> + - assigned-clocks
> + - assigned-clock-rates
> + - vddio-supply
> + - vdda-supply
> + - vddd-supply
> + - port
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/gpio/gpio.h>
> +
> + i2c {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + hi846: camera@20 {
> + compatible = "hynix,hi846";
> + reg = <0x20>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_csi1>;
> + clocks = <&clk 0>;
> + assigned-clocks = <&clk 0>;
> + assigned-clock-rates = <25000000>;
> + vdda-supply = <®_camera_vdda>;
> + vddd-supply = <®_camera_vddd>;
> + vddio-supply = <®_camera_vddio>;
> + reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
> + shutdown-gpios = <&gpio5 4 GPIO_ACTIVE_LOW>;
> +
> + port {
> + camera_out: endpoint {
> + remote-endpoint = <&csi1_ep1>;
> + link-frequencies = /bits/ 64
> + <80000000 200000000>;
> + data-lanes = <1 2>;
"make dt_binding_check":
Documentation/devicetree/bindings/media/i2c/hynix,hi846.example.dt.yaml:
camera@20: port:endpoint: Unevaluated properties are not allowed
('link-frequencies', 'data-lanes' were unexpected)
From schema: Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> + };
> + };
> + };
> + };
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected]
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
Am Donnerstag, dem 25.11.2021 um 12:15 +0100 schrieb Geert
Uytterhoeven:
> On Mon, Sep 6, 2021 at 12:30 PM Martin Kepplinger
> <[email protected]> wrote:
> > Document the bindings used for the SK Hynix Hi-846 CMOS camera
> > driver.
> >
> > Signed-off-by: Martin Kepplinger <[email protected]>
> > Reviewed-by: Laurent Pinchart <[email protected]>
> > Reviewed-by: Rob Herring <[email protected]>
> > ---
> > .../bindings/media/i2c/hynix,hi846.yaml | 120
> > ++++++++++++++++++
> > 1 file changed, 120 insertions(+)
> > create mode 100644
> > Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> >
> > diff --git
> > a/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> > b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> > new file mode 100644
> > index 000000000000..85a8877c2f38
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> > @@ -0,0 +1,120 @@
> > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/media/i2c/hynix,hi846.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: SK Hynix Hi-846 1/4" 8M Pixel MIPI CSI-2 sensor
> > +
> > +maintainers:
> > + - Martin Kepplinger <[email protected]>
> > +
> > +description: |-
> > + The Hi-846 is a raw image sensor with an MIPI CSI-2 image data
> > + interface and CCI (I2C compatible) control bus. The output
> > format
> > + is raw Bayer.
> > +
> > +properties:
> > + compatible:
> > + const: hynix,hi846
> > +
> > + reg:
> > + maxItems: 1
> > +
> > + clocks:
> > + items:
> > + - description: Reference to the mclk clock.
> > +
> > + assigned-clocks:
> > + maxItems: 1
> > +
> > + assigned-clock-rates:
> > + maxItems: 1
> > +
> > + reset-gpios:
> > + description: Reference to the GPIO connected to the RESETB
> > pin. Active low.
> > + maxItems: 1
> > +
> > + shutdown-gpios:
> > + description: Reference to the GPIO connected to the XSHUTDOWN
> > pin. Active low.
> > + maxItems: 1
> > +
> > + vddio-supply:
> > + description: Definition of the regulator used for the VDDIO
> > power supply.
> > +
> > + vdda-supply:
> > + description: Definition of the regulator used for the VDDA
> > power supply.
> > +
> > + vddd-supply:
> > + description: Definition of the regulator used for the VDDD
> > power supply.
> > +
> > + port:
> > + $ref: /schemas/graph.yaml#/properties/port
> > +
> > + properties:
> > + endpoint:
> > + $ref: /schemas/media/video-interfaces.yaml#
> > + unevaluatedProperties: false
> > +
> > + properties:
> > + data-lanes:
> > + oneOf:
> > + - items:
> > + - const: 1
> > + - const: 2
> > + - const: 3
> > + - const: 4
> > + - items:
> > + - const: 1
> > + - const: 2
> > +
> > + required:
> > + - data-lanes
> > +
> > +required:
> > + - compatible
> > + - reg
> > + - clocks
> > + - assigned-clocks
> > + - assigned-clock-rates
> > + - vddio-supply
> > + - vdda-supply
> > + - vddd-supply
> > + - port
> > +
> > +additionalProperties: false
> > +
> > +examples:
> > + - |
> > + #include <dt-bindings/gpio/gpio.h>
> > +
> > + i2c {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + hi846: camera@20 {
> > + compatible = "hynix,hi846";
> > + reg = <0x20>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_csi1>;
> > + clocks = <&clk 0>;
> > + assigned-clocks = <&clk 0>;
> > + assigned-clock-rates = <25000000>;
> > + vdda-supply = <®_camera_vdda>;
> > + vddd-supply = <®_camera_vddd>;
> > + vddio-supply = <®_camera_vddio>;
> > + reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
> > + shutdown-gpios = <&gpio5 4 GPIO_ACTIVE_LOW>;
> > +
> > + port {
> > + camera_out: endpoint {
> > + remote-endpoint = <&csi1_ep1>;
> > + link-frequencies = /bits/ 64
> > + <80000000 200000000>;
> > + data-lanes = <1 2>;
>
> "make dt_binding_check":
>
>
> Documentation/devicetree/bindings/media/i2c/hynix,hi846.example.dt.ya
> ml:
> camera@20: port:endpoint: Unevaluated properties are not allowed
> ('link-frequencies', 'data-lanes' were unexpected)
> From schema:
> Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
>
> > + };
> > + };
> > + };
> > + };
>
> Gr{oetje,eeting}s,
>
> Geert
thanks a lot Geert, but I can't reproduce this on linux-next. Which
tree did you run it against?
What I *do* see is the following during dtbs_check, so I guess I could
remove "orientation" and "rotation" from the example, which would be
kind of sad because these useful properties are not yet too wide know
anyway in the media device driver world...
/home/martin/dev/purism-forks/linux-
next/arch/arm64/boot/dts/freescale/imx8mq-librem5-r2.dt.yaml:
camera-front@20: 'orientation', 'rotation' do not match any of the
regexes: 'pinctrl-[0-9]+'
From schema: /home/martin/dev/purism-forks/linux-
next/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
if you can be more speicific I'll definitely try to reproduce again
though.
thanks,
martin
Hi Martin,
On Fri, Nov 26, 2021 at 11:02:31AM +0100, Martin Kepplinger wrote:
> Am Donnerstag, dem 25.11.2021 um 12:15 +0100 schrieb Geert
> Uytterhoeven:
> > On Mon, Sep 6, 2021 at 12:30 PM Martin Kepplinger
> > <[email protected]> wrote:
> > > Document the bindings used for the SK Hynix Hi-846 CMOS camera
> > > driver.
> > >
> > > Signed-off-by: Martin Kepplinger <[email protected]>
> > > Reviewed-by: Laurent Pinchart <[email protected]>
> > > Reviewed-by: Rob Herring <[email protected]>
> > > ---
> > > ?.../bindings/media/i2c/hynix,hi846.yaml?????? | 120
> > > ++++++++++++++++++
> > > ?1 file changed, 120 insertions(+)
> > > ?create mode 100644
> > > Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> > >
> > > diff --git
> > > a/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> > > b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> > > new file mode 100644
> > > index 000000000000..85a8877c2f38
> > > --- /dev/null
> > > +++ b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> > > @@ -0,0 +1,120 @@
> > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > > +%YAML 1.2
> > > +---
> > > +$id: http://devicetree.org/schemas/media/i2c/hynix,hi846.yaml#
> > > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > > +
> > > +title: SK Hynix Hi-846 1/4" 8M Pixel MIPI CSI-2 sensor
> > > +
> > > +maintainers:
> > > +? - Martin Kepplinger <[email protected]>
> > > +
> > > +description: |-
> > > +? The Hi-846 is a raw image sensor with an MIPI CSI-2 image data
> > > +? interface and CCI (I2C compatible) control bus. The output
> > > format
> > > +? is raw Bayer.
> > > +
> > > +properties:
> > > +? compatible:
> > > +??? const: hynix,hi846
> > > +
> > > +? reg:
> > > +??? maxItems: 1
> > > +
> > > +? clocks:
> > > +??? items:
> > > +????? - description: Reference to the mclk clock.
> > > +
> > > +? assigned-clocks:
> > > +??? maxItems: 1
> > > +
> > > +? assigned-clock-rates:
> > > +??? maxItems: 1
> > > +
> > > +? reset-gpios:
> > > +??? description: Reference to the GPIO connected to the RESETB
> > > pin. Active low.
> > > +??? maxItems: 1
> > > +
> > > +? shutdown-gpios:
> > > +??? description: Reference to the GPIO connected to the XSHUTDOWN
> > > pin. Active low.
> > > +??? maxItems: 1
> > > +
> > > +? vddio-supply:
> > > +??? description: Definition of the regulator used for the VDDIO
> > > power supply.
> > > +
> > > +? vdda-supply:
> > > +??? description: Definition of the regulator used for the VDDA
> > > power supply.
> > > +
> > > +? vddd-supply:
> > > +??? description: Definition of the regulator used for the VDDD
> > > power supply.
> > > +
> > > +? port:
> > > +??? $ref: /schemas/graph.yaml#/properties/port
> > > +
> > > +??? properties:
> > > +????? endpoint:
> > > +??????? $ref: /schemas/media/video-interfaces.yaml#
> > > +??????? unevaluatedProperties: false
> > > +
> > > +??????? properties:
> > > +????????? data-lanes:
> > > +??????????? oneOf:
> > > +????????????? - items:
> > > +????????????????? - const: 1
> > > +????????????????? - const: 2
> > > +????????????????? - const: 3
> > > +????????????????? - const: 4
> > > +????????????? - items:
> > > +????????????????? - const: 1
> > > +????????????????? - const: 2
> > > +
> > > +??????? required:
> > > +????????? - data-lanes
> > > +
> > > +required:
> > > +? - compatible
> > > +? - reg
> > > +? - clocks
> > > +? - assigned-clocks
> > > +? - assigned-clock-rates
> > > +? - vddio-supply
> > > +? - vdda-supply
> > > +? - vddd-supply
> > > +? - port
> > > +
> > > +additionalProperties: false
> > > +
> > > +examples:
> > > +? - |
> > > +??? #include <dt-bindings/gpio/gpio.h>
> > > +
> > > +??? i2c {
> > > +??????? #address-cells = <1>;
> > > +??????? #size-cells = <0>;
> > > +
> > > +??????? hi846: camera@20 {
> > > +??????????? compatible = "hynix,hi846";
> > > +??????????? reg = <0x20>;
> > > +??????????? pinctrl-names = "default";
> > > +??????????? pinctrl-0 = <&pinctrl_csi1>;
> > > +??????????? clocks = <&clk 0>;
> > > +??????????? assigned-clocks = <&clk 0>;
> > > +??????????? assigned-clock-rates = <25000000>;
> > > +??????????? vdda-supply = <®_camera_vdda>;
> > > +??????????? vddd-supply = <®_camera_vddd>;
> > > +??????????? vddio-supply = <®_camera_vddio>;
> > > +??????????? reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
> > > +??????????? shutdown-gpios = <&gpio5 4 GPIO_ACTIVE_LOW>;
> > > +
> > > +??????????? port {
> > > +??????????????? camera_out: endpoint {
> > > +??????????????????? remote-endpoint = <&csi1_ep1>;
> > > +??????????????????? link-frequencies = /bits/ 64
> > > +??????????????????????? <80000000 200000000>;
> > > +??????????????????? data-lanes = <1 2>;
> >
> > "make dt_binding_check":
> >
> > ???
> > Documentation/devicetree/bindings/media/i2c/hynix,hi846.example.dt.ya
> > ml:
> > camera@20: port:endpoint: Unevaluated properties are not allowed
> > ('link-frequencies', 'data-lanes' were unexpected)
> > ??? From schema:
> > Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> >
> > > +??????????????? };
> > > +??????????? };
> > > +??????? };
> > > +??? };
> >
> > Gr{oetje,eeting}s,
> >
> > ??????????????????????? Geert
>
>
> thanks a lot Geert, but I can't reproduce this on linux-next. Which
> tree did you run it against?
>
> What I *do* see is the following during dtbs_check, so I guess I could
> remove "orientation" and "rotation" from the example, which would be
> kind of sad because these useful properties are not yet too wide know
> anyway in the media device driver world...
>
> /home/martin/dev/purism-forks/linux-
> next/arch/arm64/boot/dts/freescale/imx8mq-librem5-r2.dt.yaml:
> camera-front@20: 'orientation', 'rotation' do not match any of the
> regexes: 'pinctrl-[0-9]+'
> From schema: /home/martin/dev/purism-forks/linux-
> next/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
>
>
> if you can be more speicific I'll definitely try to reproduce again
> though.
link-frequencies is present in the example (as it needs to be) but missing
from required properties. I don't know why there's a complaint about
data-lanes though.
--
Regards,
Sakari Ailus
Hi Martin,
On Fri, Nov 26, 2021 at 11:18 AM Sakari Ailus <[email protected]> wrote:
> On Fri, Nov 26, 2021 at 11:02:31AM +0100, Martin Kepplinger wrote:
> > Am Donnerstag, dem 25.11.2021 um 12:15 +0100 schrieb Geert
> > Uytterhoeven:
> > > On Mon, Sep 6, 2021 at 12:30 PM Martin Kepplinger
> > > <[email protected]> wrote:
> > > > Document the bindings used for the SK Hynix Hi-846 CMOS camera
> > > > driver.
> > > >
> > > > Signed-off-by: Martin Kepplinger <[email protected]>
> > > > Reviewed-by: Laurent Pinchart <[email protected]>
> > > > Reviewed-by: Rob Herring <[email protected]>
> > > > ---
> > > > .../bindings/media/i2c/hynix,hi846.yaml | 120
> > > > ++++++++++++++++++
> > > > 1 file changed, 120 insertions(+)
> > > > create mode 100644
> > > > Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> > > >
> > > > diff --git
> > > > a/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> > > > b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> > > > new file mode 100644
> > > > index 000000000000..85a8877c2f38
> > > > --- /dev/null
> > > > +++ b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> > > > @@ -0,0 +1,120 @@
> > > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > > > +%YAML 1.2
> > > > +---
> > > > +$id: http://devicetree.org/schemas/media/i2c/hynix,hi846.yaml#
> > > > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > > > +
> > > > +title: SK Hynix Hi-846 1/4" 8M Pixel MIPI CSI-2 sensor
> > > > +
> > > > +maintainers:
> > > > + - Martin Kepplinger <[email protected]>
> > > > +
> > > > +description: |-
> > > > + The Hi-846 is a raw image sensor with an MIPI CSI-2 image data
> > > > + interface and CCI (I2C compatible) control bus. The output
> > > > format
> > > > + is raw Bayer.
> > > > +
> > > > +properties:
> > > > + compatible:
> > > > + const: hynix,hi846
> > > > +
> > > > + reg:
> > > > + maxItems: 1
> > > > +
> > > > + clocks:
> > > > + items:
> > > > + - description: Reference to the mclk clock.
> > > > +
> > > > + assigned-clocks:
> > > > + maxItems: 1
> > > > +
> > > > + assigned-clock-rates:
> > > > + maxItems: 1
> > > > +
> > > > + reset-gpios:
> > > > + description: Reference to the GPIO connected to the RESETB
> > > > pin. Active low.
> > > > + maxItems: 1
> > > > +
> > > > + shutdown-gpios:
> > > > + description: Reference to the GPIO connected to the XSHUTDOWN
> > > > pin. Active low.
> > > > + maxItems: 1
> > > > +
> > > > + vddio-supply:
> > > > + description: Definition of the regulator used for the VDDIO
> > > > power supply.
> > > > +
> > > > + vdda-supply:
> > > > + description: Definition of the regulator used for the VDDA
> > > > power supply.
> > > > +
> > > > + vddd-supply:
> > > > + description: Definition of the regulator used for the VDDD
> > > > power supply.
> > > > +
> > > > + port:
> > > > + $ref: /schemas/graph.yaml#/properties/port
> > > > +
> > > > + properties:
> > > > + endpoint:
> > > > + $ref: /schemas/media/video-interfaces.yaml#
> > > > + unevaluatedProperties: false
> > > > +
> > > > + properties:
> > > > + data-lanes:
> > > > + oneOf:
> > > > + - items:
> > > > + - const: 1
> > > > + - const: 2
> > > > + - const: 3
> > > > + - const: 4
> > > > + - items:
> > > > + - const: 1
> > > > + - const: 2
> > > > +
> > > > + required:
> > > > + - data-lanes
> > > > +
> > > > +required:
> > > > + - compatible
> > > > + - reg
> > > > + - clocks
> > > > + - assigned-clocks
> > > > + - assigned-clock-rates
> > > > + - vddio-supply
> > > > + - vdda-supply
> > > > + - vddd-supply
> > > > + - port
> > > > +
> > > > +additionalProperties: false
> > > > +
> > > > +examples:
> > > > + - |
> > > > + #include <dt-bindings/gpio/gpio.h>
> > > > +
> > > > + i2c {
> > > > + #address-cells = <1>;
> > > > + #size-cells = <0>;
> > > > +
> > > > + hi846: camera@20 {
> > > > + compatible = "hynix,hi846";
> > > > + reg = <0x20>;
> > > > + pinctrl-names = "default";
> > > > + pinctrl-0 = <&pinctrl_csi1>;
> > > > + clocks = <&clk 0>;
> > > > + assigned-clocks = <&clk 0>;
> > > > + assigned-clock-rates = <25000000>;
> > > > + vdda-supply = <®_camera_vdda>;
> > > > + vddd-supply = <®_camera_vddd>;
> > > > + vddio-supply = <®_camera_vddio>;
> > > > + reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
> > > > + shutdown-gpios = <&gpio5 4 GPIO_ACTIVE_LOW>;
> > > > +
> > > > + port {
> > > > + camera_out: endpoint {
> > > > + remote-endpoint = <&csi1_ep1>;
> > > > + link-frequencies = /bits/ 64
> > > > + <80000000 200000000>;
> > > > + data-lanes = <1 2>;
> > >
> > > "make dt_binding_check":
> > >
> > >
> > > Documentation/devicetree/bindings/media/i2c/hynix,hi846.example.dt.ya
> > > ml:
> > > camera@20: port:endpoint: Unevaluated properties are not allowed
> > > ('link-frequencies', 'data-lanes' were unexpected)
> > > From schema:
> > > Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> > >
> > > > + };
> > > > + };
> > > > + };
> > > > + };
> > >
> > > Gr{oetje,eeting}s,
> > >
> > > Geert
> >
> >
> > thanks a lot Geert, but I can't reproduce this on linux-next. Which
> > tree did you run it against?
> >
> > What I *do* see is the following during dtbs_check, so I guess I could
> > remove "orientation" and "rotation" from the example, which would be
> > kind of sad because these useful properties are not yet too wide know
> > anyway in the media device driver world...
> >
> > /home/martin/dev/purism-forks/linux-
> > next/arch/arm64/boot/dts/freescale/imx8mq-librem5-r2.dt.yaml:
> > camera-front@20: 'orientation', 'rotation' do not match any of the
> > regexes: 'pinctrl-[0-9]+'
> > From schema: /home/martin/dev/purism-forks/linux-
> > next/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> >
> >
> > if you can be more speicific I'll definitely try to reproduce again
> > though.
This is reproducible on next-20211126.
Is your dt-schema up-to-date?
> link-frequencies is present in the example (as it needs to be) but missing
> from required properties. I don't know why there's a complaint about
> data-lanes though.
I also don't know what's wrong with data-lanes (else I would have
sent a patch to fix it ;-)
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected]
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
Am Freitag, dem 26.11.2021 um 13:03 +0100 schrieb Geert Uytterhoeven:
> Hi Martin,
>
> On Fri, Nov 26, 2021 at 11:18 AM Sakari Ailus <[email protected]>
> wrote:
> > On Fri, Nov 26, 2021 at 11:02:31AM +0100, Martin Kepplinger wrote:
> > > Am Donnerstag, dem 25.11.2021 um 12:15 +0100 schrieb Geert
> > > Uytterhoeven:
> > > > On Mon, Sep 6, 2021 at 12:30 PM Martin Kepplinger
> > > > <[email protected]> wrote:
> > > > > Document the bindings used for the SK Hynix Hi-846 CMOS
> > > > > camera
> > > > > driver.
> > > > >
> > > > > Signed-off-by: Martin Kepplinger <[email protected]>
> > > > > Reviewed-by: Laurent Pinchart <
> > > > > [email protected]>
> > > > > Reviewed-by: Rob Herring <[email protected]>
> > > > > ---
> > > > > .../bindings/media/i2c/hynix,hi846.yaml | 120
> > > > > ++++++++++++++++++
> > > > > 1 file changed, 120 insertions(+)
> > > > > create mode 100644
> > > > > Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> > > > >
> > > > > diff --git
> > > > > a/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yam
> > > > > l
> > > > > b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yam
> > > > > l
> > > > > new file mode 100644
> > > > > index 000000000000..85a8877c2f38
> > > > > --- /dev/null
> > > > > +++
> > > > > b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yam
> > > > > l
> > > > > @@ -0,0 +1,120 @@
> > > > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > > > > +%YAML 1.2
> > > > > +---
> > > > > +$id:
> > > > > http://devicetree.org/schemas/media/i2c/hynix,hi846.yaml#
> > > > > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > > > > +
> > > > > +title: SK Hynix Hi-846 1/4" 8M Pixel MIPI CSI-2 sensor
> > > > > +
> > > > > +maintainers:
> > > > > + - Martin Kepplinger <[email protected]>
> > > > > +
> > > > > +description: |-
> > > > > + The Hi-846 is a raw image sensor with an MIPI CSI-2 image
> > > > > data
> > > > > + interface and CCI (I2C compatible) control bus. The output
> > > > > format
> > > > > + is raw Bayer.
> > > > > +
> > > > > +properties:
> > > > > + compatible:
> > > > > + const: hynix,hi846
> > > > > +
> > > > > + reg:
> > > > > + maxItems: 1
> > > > > +
> > > > > + clocks:
> > > > > + items:
> > > > > + - description: Reference to the mclk clock.
> > > > > +
> > > > > + assigned-clocks:
> > > > > + maxItems: 1
> > > > > +
> > > > > + assigned-clock-rates:
> > > > > + maxItems: 1
> > > > > +
> > > > > + reset-gpios:
> > > > > + description: Reference to the GPIO connected to the
> > > > > RESETB
> > > > > pin. Active low.
> > > > > + maxItems: 1
> > > > > +
> > > > > + shutdown-gpios:
> > > > > + description: Reference to the GPIO connected to the
> > > > > XSHUTDOWN
> > > > > pin. Active low.
> > > > > + maxItems: 1
> > > > > +
> > > > > + vddio-supply:
> > > > > + description: Definition of the regulator used for the
> > > > > VDDIO
> > > > > power supply.
> > > > > +
> > > > > + vdda-supply:
> > > > > + description: Definition of the regulator used for the
> > > > > VDDA
> > > > > power supply.
> > > > > +
> > > > > + vddd-supply:
> > > > > + description: Definition of the regulator used for the
> > > > > VDDD
> > > > > power supply.
> > > > > +
> > > > > + port:
> > > > > + $ref: /schemas/graph.yaml#/properties/port
> > > > > +
> > > > > + properties:
> > > > > + endpoint:
> > > > > + $ref: /schemas/media/video-interfaces.yaml#
> > > > > + unevaluatedProperties: false
> > > > > +
> > > > > + properties:
> > > > > + data-lanes:
> > > > > + oneOf:
> > > > > + - items:
> > > > > + - const: 1
> > > > > + - const: 2
> > > > > + - const: 3
> > > > > + - const: 4
> > > > > + - items:
> > > > > + - const: 1
> > > > > + - const: 2
> > > > > +
> > > > > + required:
> > > > > + - data-lanes
> > > > > +
> > > > > +required:
> > > > > + - compatible
> > > > > + - reg
> > > > > + - clocks
> > > > > + - assigned-clocks
> > > > > + - assigned-clock-rates
> > > > > + - vddio-supply
> > > > > + - vdda-supply
> > > > > + - vddd-supply
> > > > > + - port
> > > > > +
> > > > > +additionalProperties: false
> > > > > +
> > > > > +examples:
> > > > > + - |
> > > > > + #include <dt-bindings/gpio/gpio.h>
> > > > > +
> > > > > + i2c {
> > > > > + #address-cells = <1>;
> > > > > + #size-cells = <0>;
> > > > > +
> > > > > + hi846: camera@20 {
> > > > > + compatible = "hynix,hi846";
> > > > > + reg = <0x20>;
> > > > > + pinctrl-names = "default";
> > > > > + pinctrl-0 = <&pinctrl_csi1>;
> > > > > + clocks = <&clk 0>;
> > > > > + assigned-clocks = <&clk 0>;
> > > > > + assigned-clock-rates = <25000000>;
> > > > > + vdda-supply = <®_camera_vdda>;
> > > > > + vddd-supply = <®_camera_vddd>;
> > > > > + vddio-supply = <®_camera_vddio>;
> > > > > + reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
> > > > > + shutdown-gpios = <&gpio5 4 GPIO_ACTIVE_LOW>;
> > > > > +
> > > > > + port {
> > > > > + camera_out: endpoint {
> > > > > + remote-endpoint = <&csi1_ep1>;
> > > > > + link-frequencies = /bits/ 64
> > > > > + <80000000 200000000>;
> > > > > + data-lanes = <1 2>;
> > > >
> > > > "make dt_binding_check":
> > > >
> > > >
> > > > Documentation/devicetree/bindings/media/i2c/hynix,hi846.example
> > > > .dt.ya
> > > > ml:
> > > > camera@20: port:endpoint: Unevaluated properties are not
> > > > allowed
> > > > ('link-frequencies', 'data-lanes' were unexpected)
> > > > From schema:
> > > > Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> > > >
> > > > > + };
> > > > > + };
> > > > > + };
> > > > > + };
> > > >
> > > > Gr{oetje,eeting}s,
> > > >
> > > > Geert
> > >
> > >
> > > thanks a lot Geert, but I can't reproduce this on linux-next.
> > > Which
> > > tree did you run it against?
> > >
> > > What I *do* see is the following during dtbs_check, so I guess I
> > > could
> > > remove "orientation" and "rotation" from the example, which would
> > > be
> > > kind of sad because these useful properties are not yet too wide
> > > know
> > > anyway in the media device driver world...
> > >
> > > /home/martin/dev/purism-forks/linux-
> > > next/arch/arm64/boot/dts/freescale/imx8mq-librem5-r2.dt.yaml:
> > > camera-front@20: 'orientation', 'rotation' do not match any of
> > > the
> > > regexes: 'pinctrl-[0-9]+'
> > > From schema: /home/martin/dev/purism-forks/linux-
> > > next/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> > >
> > >
> > > if you can be more speicific I'll definitely try to reproduce
> > > again
> > > though.
>
> This is reproducible on next-20211126.
> Is your dt-schema up-to-date?
it is now, I'm running
make -j7 ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- dt_binding_check
dtbs_check
but I can't reproduce that error. weird.
>
> > link-frequencies is present in the example (as it needs to be) but
> > missing
> > from required properties. I don't know why there's a complaint
> > about
> > data-lanes though.
>
> I also don't know what's wrong with data-lanes (else I would have
> sent a patch to fix it ;-)
>
> Gr{oetje,eeting}s,
>
> Geert
>
> --
> Geert Uytterhoeven -- There's lots of Linux beyond ia32 --
> [email protected]
>
> In personal conversations with technical people, I call myself a
> hacker. But
> when I'm talking to journalists I just say "programmer" or something
> like that.
> -- Linus Torvalds
Hi Martin,
On Tue, Nov 30, 2021 at 3:57 PM Martin Kepplinger
<[email protected]> wrote:
> Am Freitag, dem 26.11.2021 um 13:03 +0100 schrieb Geert Uytterhoeven:
> > This is reproducible on next-20211126.
> > Is your dt-schema up-to-date?
>
> it is now, I'm running
>
> make -j7 ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- dt_binding_check
> dtbs_check
>
> but I can't reproduce that error. weird.
Interesting...
$ git checkout next-20211201
$ make -j 12 ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- dt_binding_check
[...]
CHECK Documentation/devicetree/bindings/media/i2c/rda,rda5807.example.dt.yaml
Documentation/devicetree/bindings/media/i2c/hynix,hi846.example.dt.yaml:
camera@20: port:endpoint: Unevaluated properties are not allowed
('link-frequencies', 'data-lanes' were unexpected)
From schema:
Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
My userland is Ubuntu 20.04.3 LTS.
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected]
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
On Mon, Sep 6, 2021 at 5:29 AM Martin Kepplinger
<[email protected]> wrote:
>
> Document the bindings used for the SK Hynix Hi-846 CMOS camera driver.
>
> Signed-off-by: Martin Kepplinger <[email protected]>
> Reviewed-by: Laurent Pinchart <[email protected]>
> Reviewed-by: Rob Herring <[email protected]>
> ---
> .../bindings/media/i2c/hynix,hi846.yaml | 120 ++++++++++++++++++
> 1 file changed, 120 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
>
> diff --git a/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> new file mode 100644
> index 000000000000..85a8877c2f38
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> @@ -0,0 +1,120 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/media/i2c/hynix,hi846.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: SK Hynix Hi-846 1/4" 8M Pixel MIPI CSI-2 sensor
> +
> +maintainers:
> + - Martin Kepplinger <[email protected]>
> +
> +description: |-
> + The Hi-846 is a raw image sensor with an MIPI CSI-2 image data
> + interface and CCI (I2C compatible) control bus. The output format
> + is raw Bayer.
> +
> +properties:
> + compatible:
> + const: hynix,hi846
> +
> + reg:
> + maxItems: 1
> +
> + clocks:
> + items:
> + - description: Reference to the mclk clock.
> +
> + assigned-clocks:
> + maxItems: 1
> +
> + assigned-clock-rates:
> + maxItems: 1
> +
> + reset-gpios:
> + description: Reference to the GPIO connected to the RESETB pin. Active low.
> + maxItems: 1
> +
> + shutdown-gpios:
> + description: Reference to the GPIO connected to the XSHUTDOWN pin. Active low.
> + maxItems: 1
> +
> + vddio-supply:
> + description: Definition of the regulator used for the VDDIO power supply.
> +
> + vdda-supply:
> + description: Definition of the regulator used for the VDDA power supply.
> +
> + vddd-supply:
> + description: Definition of the regulator used for the VDDD power supply.
> +
> + port:
> + $ref: /schemas/graph.yaml#/properties/port
This needs to be:
$ref: /schemas/graph.yaml#/$defs/port-base
to fix the warning reported. You have to use the 'main' branch of
dtschema which has unevaluatedProperties support. I'll be making a
release soonish.
Rob
On Fri, Dec 3, 2021 at 10:19 AM Rob Herring <[email protected]> wrote:
>
> On Mon, Sep 6, 2021 at 5:29 AM Martin Kepplinger
> <[email protected]> wrote:
> >
> > Document the bindings used for the SK Hynix Hi-846 CMOS camera driver.
> >
> > Signed-off-by: Martin Kepplinger <[email protected]>
> > Reviewed-by: Laurent Pinchart <[email protected]>
> > Reviewed-by: Rob Herring <[email protected]>
> > ---
> > .../bindings/media/i2c/hynix,hi846.yaml | 120 ++++++++++++++++++
> > 1 file changed, 120 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> >
> > diff --git a/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> > new file mode 100644
> > index 000000000000..85a8877c2f38
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> > @@ -0,0 +1,120 @@
> > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/media/i2c/hynix,hi846.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: SK Hynix Hi-846 1/4" 8M Pixel MIPI CSI-2 sensor
> > +
> > +maintainers:
> > + - Martin Kepplinger <[email protected]>
> > +
> > +description: |-
> > + The Hi-846 is a raw image sensor with an MIPI CSI-2 image data
> > + interface and CCI (I2C compatible) control bus. The output format
> > + is raw Bayer.
> > +
> > +properties:
> > + compatible:
> > + const: hynix,hi846
> > +
> > + reg:
> > + maxItems: 1
> > +
> > + clocks:
> > + items:
> > + - description: Reference to the mclk clock.
> > +
> > + assigned-clocks:
> > + maxItems: 1
> > +
> > + assigned-clock-rates:
> > + maxItems: 1
> > +
> > + reset-gpios:
> > + description: Reference to the GPIO connected to the RESETB pin. Active low.
> > + maxItems: 1
> > +
> > + shutdown-gpios:
> > + description: Reference to the GPIO connected to the XSHUTDOWN pin. Active low.
> > + maxItems: 1
> > +
> > + vddio-supply:
> > + description: Definition of the regulator used for the VDDIO power supply.
> > +
> > + vdda-supply:
> > + description: Definition of the regulator used for the VDDA power supply.
> > +
> > + vddd-supply:
> > + description: Definition of the regulator used for the VDDD power supply.
> > +
> > + port:
> > + $ref: /schemas/graph.yaml#/properties/port
>
> This needs to be:
>
> $ref: /schemas/graph.yaml#/$defs/port-base
>
> to fix the warning reported. You have to use the 'main' branch of
> dtschema which has unevaluatedProperties support. I'll be making a
> release soonish.
This is still failing, can you please fix it.
Rob
Am Mittwoch, dem 05.01.2022 um 10:23 -0600 schrieb Rob Herring:
> On Fri, Dec 3, 2021 at 10:19 AM Rob Herring <[email protected]> wrote:
> >
> > On Mon, Sep 6, 2021 at 5:29 AM Martin Kepplinger
> > <[email protected]> wrote:
> > >
> > > Document the bindings used for the SK Hynix Hi-846 CMOS camera
> > > driver.
> > >
> > > Signed-off-by: Martin Kepplinger <[email protected]>
> > > Reviewed-by: Laurent Pinchart <[email protected]>
> > > Reviewed-by: Rob Herring <[email protected]>
> > > ---
> > > .../bindings/media/i2c/hynix,hi846.yaml | 120
> > > ++++++++++++++++++
> > > 1 file changed, 120 insertions(+)
> > > create mode 100644
> > > Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> > >
> > > diff --git
> > > a/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> > > b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> > > new file mode 100644
> > > index 000000000000..85a8877c2f38
> > > --- /dev/null
> > > +++
> > > b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> > > @@ -0,0 +1,120 @@
> > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > > +%YAML 1.2
> > > +---
> > > +$id: http://devicetree.org/schemas/media/i2c/hynix,hi846.yaml#
> > > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > > +
> > > +title: SK Hynix Hi-846 1/4" 8M Pixel MIPI CSI-2 sensor
> > > +
> > > +maintainers:
> > > + - Martin Kepplinger <[email protected]>
> > > +
> > > +description: |-
> > > + The Hi-846 is a raw image sensor with an MIPI CSI-2 image data
> > > + interface and CCI (I2C compatible) control bus. The output
> > > format
> > > + is raw Bayer.
> > > +
> > > +properties:
> > > + compatible:
> > > + const: hynix,hi846
> > > +
> > > + reg:
> > > + maxItems: 1
> > > +
> > > + clocks:
> > > + items:
> > > + - description: Reference to the mclk clock.
> > > +
> > > + assigned-clocks:
> > > + maxItems: 1
> > > +
> > > + assigned-clock-rates:
> > > + maxItems: 1
> > > +
> > > + reset-gpios:
> > > + description: Reference to the GPIO connected to the RESETB
> > > pin. Active low.
> > > + maxItems: 1
> > > +
> > > + shutdown-gpios:
> > > + description: Reference to the GPIO connected to the
> > > XSHUTDOWN pin. Active low.
> > > + maxItems: 1
> > > +
> > > + vddio-supply:
> > > + description: Definition of the regulator used for the VDDIO
> > > power supply.
> > > +
> > > + vdda-supply:
> > > + description: Definition of the regulator used for the VDDA
> > > power supply.
> > > +
> > > + vddd-supply:
> > > + description: Definition of the regulator used for the VDDD
> > > power supply.
> > > +
> > > + port:
> > > + $ref: /schemas/graph.yaml#/properties/port
> >
> > This needs to be:
> >
> > $ref: /schemas/graph.yaml#/$defs/port-base
> >
> > to fix the warning reported. You have to use the 'main' branch of
> > dtschema which has unevaluatedProperties support. I'll be making a
> > release soonish.
>
> This is still failing, can you please fix it.
>
> Rob
Yes I'll send a patch next week. thanks for the reminder,
martin