2021-08-09 07:47:14

by Puranjay Mohan

[permalink] [raw]
Subject: [PATCH v9 0/2] iio: accel: add support for ADXL355

Add the dt-bindings and the driver for ADXL355 3-axis MEMS Accelerometer.

Changes since v8:
1. Make scale and offset defines inline and remove them.
2. Change dt-binding doc to state interrupt polarity only for DRDY pin.
3. Remove triggered buffer support from this patch series.

Changes since v7:
1. Update MAINTAINERS to show all driver files.
2. Set CONFIGS for buffered support in Kconfig.

Changes since v6:
1. Use interrupt-names property in device tree document.
2. Add triggered buffer support.
3. Use a static table for offset and data registers.
4. Fix coding style issues.
5. move defines from header to c file.

Changes since v5:
1. Used get_unaligned_be24() and get_unaligned_be16() to parse
acceleration and temperature data. This solves sparse errors and also
make the code more understandable.

Changes since v4:
1. Fix errors reported by sparse.

Changes since v3:
1. Fix errors in yaml DT doc.
2. Change SPDX-License-Identifier to GPL-2.0-only OR BSD-2-Clause

Changes since v2:
1. Add separate DT binding doc in yaml.
2. Use ____cacheline_aligned buffer for regmap_bulk_read/write calls.
3. Make code consistent by using same style in switch case.
4. Use FIELD_PREP in place of custom macros.
5. Make Kconfig description more informative.

Changes since v1:
1. Remove the declarations for static regmap structures from adxl355.h.
This was missed in the v1 and caused errors.
2. Make switch case statements consistent by directly returning from
each case rather than saving the return in a variable.
3. Some coding style changes.

Changes since v0:
1. Move adxl355_hpf_3db_table to adxl355_data structure. This is done to make
sure that each device gets its own table.
2. Make local regmap definitions private to adxl355_core.c.
3. Other minor coding style changes.

Puranjay Mohan (2):
iio: accel: Add driver support for ADXL355
iio: accel: adxl355: Add triggered buffer support

MAINTAINERS | 10 +
drivers/iio/accel/Kconfig | 33 ++
drivers/iio/accel/Makefile | 3 +
drivers/iio/accel/adxl355.h | 19 +
drivers/iio/accel/adxl355_core.c | 676 +++++++++++++++++++++++++++++++
drivers/iio/accel/adxl355_i2c.c | 65 +++
drivers/iio/accel/adxl355_spi.c | 67 +++
7 files changed, 873 insertions(+)
create mode 100644 drivers/iio/accel/adxl355.h
create mode 100644 drivers/iio/accel/adxl355_core.c
create mode 100644 drivers/iio/accel/adxl355_i2c.c
create mode 100644 drivers/iio/accel/adxl355_spi.c

--
2.30.1


2021-08-09 07:47:38

by Puranjay Mohan

[permalink] [raw]
Subject: [PATCH v9 1/2] iio: accel: Add driver support for ADXL355

ADXL355 is 3-axis MEMS Accelerometer. It offers low noise density,
low 0g offset drift, low power with selectable measurement ranges.
It also features programmable high-pass and low-pass filters.

Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/adxl354_adxl355.pdf
Signed-off-by: Puranjay Mohan <[email protected]>
---
MAINTAINERS | 10 +
drivers/iio/accel/Kconfig | 29 ++
drivers/iio/accel/Makefile | 3 +
drivers/iio/accel/adxl355.h | 19 +
drivers/iio/accel/adxl355_core.c | 578 +++++++++++++++++++++++++++++++
drivers/iio/accel/adxl355_i2c.c | 64 ++++
drivers/iio/accel/adxl355_spi.c | 67 ++++
7 files changed, 770 insertions(+)
create mode 100644 drivers/iio/accel/adxl355.h
create mode 100644 drivers/iio/accel/adxl355_core.c
create mode 100644 drivers/iio/accel/adxl355_i2c.c
create mode 100644 drivers/iio/accel/adxl355_spi.c

diff --git a/MAINTAINERS b/MAINTAINERS
index bd7aff0c1..704e70b86 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -586,6 +586,16 @@ W: http://ez.analog.com/community/linux-device-drivers
F: Documentation/devicetree/bindings/iio/accel/adi,adxl345.yaml
F: drivers/input/misc/adxl34x.c

+ADXL355 THREE-AXIS DIGITAL ACCELEROMETER DRIVER
+M: Puranjay Mohan <[email protected]>
+L: [email protected]
+S: Supported
+F: drivers/iio/accel/adxl355.h
+F: drivers/iio/accel/adxl355_core.c
+F: drivers/iio/accel/adxl355_i2c.c
+F: drivers/iio/accel/adxl355_spi.c
+F: Documentation/devicetree/bindings/iio/accel/adi,adxl355.yaml
+
ADXL372 THREE-AXIS DIGITAL ACCELEROMETER DRIVER
M: Michael Hennerich <[email protected]>
S: Supported
diff --git a/drivers/iio/accel/Kconfig b/drivers/iio/accel/Kconfig
index cceda3cec..d0c45c809 100644
--- a/drivers/iio/accel/Kconfig
+++ b/drivers/iio/accel/Kconfig
@@ -61,6 +61,35 @@ config ADXL345_SPI
will be called adxl345_spi and you will also get adxl345_core
for the core module.

+config ADXL355
+ tristate
+
+config ADXL355_I2C
+ tristate "Analog Devices ADXL355 3-Axis Digital Accelerometer I2C Driver"
+ depends on I2C
+ select ADXL355
+ select REGMAP_I2C
+ help
+ Say Y here if you want to build i2c support for the Analog Devices
+ ADXL355 3-axis digital accelerometer.
+
+ To compile this driver as a module, choose M here: the module
+ will be called adxl355_i2c and you will also get adxl355_core
+ for the core module.
+
+config ADXL355_SPI
+ tristate "Analog Devices ADXL355 3-Axis Digital Accelerometer SPI Driver"
+ depends on SPI
+ select ADXL355
+ select REGMAP_SPI
+ help
+ Say Y here if you want to build spi support for the Analog Devices
+ ADXL355 3-axis digital accelerometer.
+
+ To compile this driver as a module, choose M here: the module
+ will be called adxl355_spi and you will also get adxl355_core
+ for the core module.
+
config ADXL372
tristate
select IIO_BUFFER
diff --git a/drivers/iio/accel/Makefile b/drivers/iio/accel/Makefile
index 32cd1342a..0e4721d2d 100644
--- a/drivers/iio/accel/Makefile
+++ b/drivers/iio/accel/Makefile
@@ -9,6 +9,9 @@ obj-$(CONFIG_ADIS16209) += adis16209.o
obj-$(CONFIG_ADXL345) += adxl345_core.o
obj-$(CONFIG_ADXL345_I2C) += adxl345_i2c.o
obj-$(CONFIG_ADXL345_SPI) += adxl345_spi.o
+obj-$(CONFIG_ADXL355) += adxl355_core.o
+obj-$(CONFIG_ADXL355_I2C) += adxl355_i2c.o
+obj-$(CONFIG_ADXL355_SPI) += adxl355_spi.o
obj-$(CONFIG_ADXL372) += adxl372.o
obj-$(CONFIG_ADXL372_I2C) += adxl372_i2c.o
obj-$(CONFIG_ADXL372_SPI) += adxl372_spi.o
diff --git a/drivers/iio/accel/adxl355.h b/drivers/iio/accel/adxl355.h
new file mode 100644
index 000000000..322b0abb8
--- /dev/null
+++ b/drivers/iio/accel/adxl355.h
@@ -0,0 +1,19 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * ADXL355 3-Axis Digital Accelerometer
+ *
+ * Copyright (c) 2021 Puranjay Mohan <[email protected]>
+ */
+
+#ifndef _ADXL355_H_
+#define _ADXL355_H_
+
+#include <linux/regmap.h>
+
+extern const struct regmap_access_table adxl355_readable_regs_tbl;
+
+extern const struct regmap_access_table adxl355_writeable_regs_tbl;
+
+int adxl355_core_probe(struct device *dev, struct regmap *regmap,
+ const char *name);
+#endif /* _ADXL355_H_ */
diff --git a/drivers/iio/accel/adxl355_core.c b/drivers/iio/accel/adxl355_core.c
new file mode 100644
index 000000000..d1163cde1
--- /dev/null
+++ b/drivers/iio/accel/adxl355_core.c
@@ -0,0 +1,578 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * ADXL355 3-Axis Digital Accelerometer IIO core driver
+ *
+ * Copyright (c) 2021 Puranjay Mohan <[email protected]>
+ *
+ * Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/adxl354_adxl355.pdf
+ */
+
+#include <asm/unaligned.h>
+#include <linux/bitfield.h>
+#include <linux/iio/iio.h>
+#include <linux/limits.h>
+#include <linux/math64.h>
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+#include <linux/regmap.h>
+
+#include "adxl355.h"
+
+/* ADXL355 Register Definitions */
+#define ADXL355_DEVID_AD_REG 0x00
+#define ADXL355_DEVID_MST_REG 0x01
+#define ADXL355_PARTID_REG 0x02
+#define ADXL355_STATUS_REG 0x04
+#define ADXL355_FIFO_ENTRIES_REG 0x05
+#define ADXL355_TEMP2_REG 0x06
+#define ADXL355_XDATA3_REG 0x08
+#define ADXL355_YDATA3_REG 0x0B
+#define ADXL355_ZDATA3_REG 0x0E
+#define ADXL355_FIFO_DATA_REG 0x11
+#define ADXL355_OFFSET_X_H_REG 0x1E
+#define ADXL355_OFFSET_Y_H_REG 0x20
+#define ADXL355_OFFSET_Z_H_REG 0x22
+#define ADXL355_ACT_EN_REG 0x24
+#define ADXL355_ACT_THRESH_H_REG 0x25
+#define ADXL355_ACT_THRESH_L_REG 0x26
+#define ADXL355_ACT_COUNT_REG 0x27
+#define ADXL355_FILTER_REG 0x28
+#define ADXL355_FILTER_ODR_MSK GENMASK(3, 0)
+#define ADXL355_FILTER_HPF_MSK GENMASK(6, 4)
+#define ADXL355_FIFO_SAMPLES_REG 0x29
+#define ADXL355_INT_MAP_REG 0x2A
+#define ADXL355_SYNC_REG 0x2B
+#define ADXL355_RANGE_REG 0x2C
+#define ADXL355_POWER_CTL_REG 0x2D
+#define ADXL355_POWER_CTL_MODE_MSK GENMASK(1, 0)
+#define ADXL355_SELF_TEST_REG 0x2E
+#define ADXL355_RESET_REG 0x2F
+
+#define ADXL355_DEVID_AD_VAL 0xAD
+#define ADXL355_DEVID_MST_VAL 0x1D
+#define ADXL355_PARTID_VAL 0xED
+#define ADXL355_RESET_CODE 0x52
+
+static const struct regmap_range adxl355_read_reg_range[] = {
+ regmap_reg_range(ADXL355_DEVID_AD_REG, ADXL355_FIFO_DATA_REG),
+ regmap_reg_range(ADXL355_OFFSET_X_H_REG, ADXL355_SELF_TEST_REG)
+};
+
+const struct regmap_access_table adxl355_readable_regs_tbl = {
+ .yes_ranges = adxl355_read_reg_range,
+ .n_yes_ranges = ARRAY_SIZE(adxl355_read_reg_range),
+};
+EXPORT_SYMBOL_GPL(adxl355_readable_regs_tbl);
+
+static const struct regmap_range adxl355_write_reg_range[] = {
+ regmap_reg_range(ADXL355_OFFSET_X_H_REG, ADXL355_RESET_REG)
+};
+
+const struct regmap_access_table adxl355_writeable_regs_tbl = {
+ .yes_ranges = adxl355_write_reg_range,
+ .n_yes_ranges = ARRAY_SIZE(adxl355_write_reg_range),
+};
+EXPORT_SYMBOL_GPL(adxl355_writeable_regs_tbl);
+
+enum adxl355_op_mode {
+ ADXL355_MEASUREMENT,
+ ADXL355_STANDBY,
+ ADXL355_TEMP_OFF
+};
+
+enum adxl355_odr {
+ ADXL355_ODR_4000HZ,
+ ADXL355_ODR_2000HZ,
+ ADXL355_ODR_1000HZ,
+ ADXL355_ODR_500HZ,
+ ADXL355_ODR_250HZ,
+ ADXL355_ODR_125HZ,
+ ADXL355_ODR_62_5HZ,
+ ADXL355_ODR_31_25HZ,
+ ADXL355_ODR_15_625HZ,
+ ADXL355_ODR_7_813HZ,
+ ADXL355_ODR_3_906HZ
+};
+
+enum adxl355_hpf_3db {
+ ADXL355_HPF_OFF,
+ ADXL355_HPF_24_7,
+ ADXL355_HPF_6_2084,
+ ADXL355_HPF_1_5545,
+ ADXL355_HPF_0_3862,
+ ADXL355_HPF_0_0954,
+ ADXL355_HPF_0_0238
+};
+
+static const int adxl355_odr_table[][2] = {
+ [0] = {4000, 0},
+ [1] = {2000, 0},
+ [2] = {1000, 0},
+ [3] = {500, 0},
+ [4] = {250, 0},
+ [5] = {125, 0},
+ [6] = {62, 500000},
+ [7] = {31, 250000},
+ [8] = {15, 625000},
+ [9] = {7, 813000},
+ [10] = {3, 906000}
+};
+
+static const int adxl355_hpf_3db_multipliers[] = {
+ 0,
+ 247000,
+ 62084,
+ 15545,
+ 3862,
+ 954,
+ 238
+};
+
+enum adxl355_chans {
+ chan_x, chan_y, chan_z
+};
+
+struct adxl355_chan_info {
+ u8 data_reg;
+ u8 offset_reg;
+};
+
+static const struct adxl355_chan_info adxl355_chans[] = {
+ [chan_x] = {
+ .data_reg = ADXL355_XDATA3_REG,
+ .offset_reg = ADXL355_OFFSET_X_H_REG
+ },
+ [chan_y] = {
+ .data_reg = ADXL355_YDATA3_REG,
+ .offset_reg = ADXL355_OFFSET_Y_H_REG
+ },
+ [chan_z] = {
+ .data_reg = ADXL355_ZDATA3_REG,
+ .offset_reg = ADXL355_OFFSET_Z_H_REG
+ }
+};
+
+struct adxl355_data {
+ struct regmap *regmap;
+ struct device *dev;
+ struct mutex lock; /* lock to protect op_mode */
+ enum adxl355_op_mode op_mode;
+ enum adxl355_odr odr;
+ enum adxl355_hpf_3db hpf_3db;
+ int calibbias[3];
+ int adxl355_hpf_3db_table[7][2];
+ u8 transf_buf[3] ____cacheline_aligned;
+};
+
+static int adxl355_set_op_mode(struct adxl355_data *data,
+ enum adxl355_op_mode op_mode)
+{
+ int ret;
+
+ if (data->op_mode == op_mode)
+ return 0;
+
+ ret = regmap_update_bits(data->regmap, ADXL355_POWER_CTL_REG,
+ ADXL355_POWER_CTL_MODE_MSK, op_mode);
+ if (ret)
+ return ret;
+
+ data->op_mode = op_mode;
+
+ return ret;
+}
+
+static void adxl355_fill_3db_frequency_table(struct adxl355_data *data)
+{
+ int i;
+ u64 rem;
+ u64 div;
+ u32 multiplier;
+ u64 odr = mul_u64_u32_shr(adxl355_odr_table[data->odr][0], 1000000, 0) +
+ adxl355_odr_table[data->odr][1];
+
+ for (i = 0; i < ARRAY_SIZE(adxl355_hpf_3db_multipliers); i++) {
+ multiplier = adxl355_hpf_3db_multipliers[i];
+ div = div64_u64_rem(mul_u64_u32_shr(odr, multiplier, 0),
+ 100000000000000UL, &rem);
+
+ data->adxl355_hpf_3db_table[i][0] = div;
+ data->adxl355_hpf_3db_table[i][1] = div_u64(rem, 100000000);
+ }
+}
+
+static int adxl355_setup(struct adxl355_data *data)
+{
+ unsigned int regval;
+ int ret;
+
+ ret = regmap_read(data->regmap, ADXL355_DEVID_AD_REG, &regval);
+ if (ret)
+ return ret;
+
+ if (regval != ADXL355_DEVID_AD_VAL) {
+ dev_err(data->dev, "Invalid ADI ID 0x%02x\n", regval);
+ return -ENODEV;
+ }
+
+ ret = regmap_read(data->regmap, ADXL355_DEVID_MST_REG, &regval);
+ if (ret)
+ return ret;
+
+ if (regval != ADXL355_DEVID_MST_VAL) {
+ dev_err(data->dev, "Invalid MEMS ID 0x%02x\n", regval);
+ return -ENODEV;
+ }
+
+ ret = regmap_read(data->regmap, ADXL355_PARTID_REG, &regval);
+ if (ret)
+ return ret;
+
+ if (regval != ADXL355_PARTID_VAL) {
+ dev_err(data->dev, "Invalid DEV ID 0x%02x\n", regval);
+ return -ENODEV;
+ }
+
+ /*
+ * Perform a software reset to make sure the device is in a consistent
+ * state after start up.
+ */
+ ret = regmap_write(data->regmap, ADXL355_RESET_REG, ADXL355_RESET_CODE);
+ if (ret)
+ return ret;
+
+ adxl355_fill_3db_frequency_table(data);
+
+ return adxl355_set_op_mode(data, ADXL355_MEASUREMENT);
+}
+
+static int adxl355_get_temp_data(struct adxl355_data *data, u8 addr)
+{
+ return regmap_bulk_read(data->regmap, addr, data->transf_buf, 2);
+}
+
+static int adxl355_read_axis(struct adxl355_data *data, u8 addr)
+{
+ int ret;
+
+ ret = regmap_bulk_read(data->regmap, addr, data->transf_buf, 3);
+ if (ret < 0)
+ return ret;
+
+ return get_unaligned_be24(data->transf_buf);
+}
+
+static int adxl355_find_match(const int (*freq_tbl)[2], const int n,
+ const int val, const int val2)
+{
+ int i;
+
+ for (i = 0; i < n; i++) {
+ if (freq_tbl[i][0] == val && freq_tbl[i][1] == val2)
+ return i;
+ }
+
+ return -EINVAL;
+}
+
+static int adxl355_set_odr(struct adxl355_data *data,
+ enum adxl355_odr odr)
+{
+ int ret = 0;
+
+ mutex_lock(&data->lock);
+
+ if (data->odr == odr)
+ goto out_unlock;
+
+ ret = adxl355_set_op_mode(data, ADXL355_STANDBY);
+ if (ret < 0)
+ goto out_unlock;
+
+ ret = regmap_update_bits(data->regmap, ADXL355_FILTER_REG,
+ ADXL355_FILTER_ODR_MSK,
+ FIELD_PREP(ADXL355_FILTER_ODR_MSK, odr));
+ if (ret < 0)
+ goto out_unlock;
+
+ data->odr = odr;
+ adxl355_fill_3db_frequency_table(data);
+
+out_unlock:
+ ret = adxl355_set_op_mode(data, ADXL355_MEASUREMENT);
+ mutex_unlock(&data->lock);
+ return ret;
+}
+
+static int adxl355_set_hpf_3db(struct adxl355_data *data,
+ enum adxl355_hpf_3db hpf)
+{
+ int ret = 0;
+
+ mutex_lock(&data->lock);
+
+ if (data->hpf_3db == hpf)
+ goto unlock;
+
+ ret = adxl355_set_op_mode(data, ADXL355_STANDBY);
+ if (ret < 0)
+ goto out_unlock;
+
+ ret = regmap_update_bits(data->regmap, ADXL355_FILTER_REG,
+ ADXL355_FILTER_HPF_MSK,
+ FIELD_PREP(ADXL355_FILTER_HPF_MSK, hpf));
+ if (!ret)
+ data->hpf_3db = hpf;
+
+out_unlock:
+ ret = adxl355_set_op_mode(data, ADXL355_MEASUREMENT);
+unlock:
+ mutex_unlock(&data->lock);
+ return ret;
+}
+
+static int adxl355_set_calibbias(struct adxl355_data *data,
+ enum adxl355_chans chan, int calibbias)
+{
+ int ret = 0;
+
+ put_unaligned_be16(calibbias, data->transf_buf);
+
+ mutex_lock(&data->lock);
+
+ ret = adxl355_set_op_mode(data, ADXL355_STANDBY);
+ if (ret < 0)
+ goto out_unlock;
+
+ ret = regmap_bulk_write(data->regmap,
+ adxl355_chans[chan].offset_reg,
+ data->transf_buf, 2);
+ if (ret)
+ goto out_unlock;
+
+ data->calibbias[chan] = calibbias;
+
+out_unlock:
+ ret = adxl355_set_op_mode(data, ADXL355_MEASUREMENT);
+ mutex_unlock(&data->lock);
+ return ret;
+}
+
+static int adxl355_read_raw(struct iio_dev *indio_dev,
+ struct iio_chan_spec const *chan,
+ int *val, int *val2, long mask)
+{
+ struct adxl355_data *data = iio_priv(indio_dev);
+ int ret;
+
+ switch (mask) {
+ case IIO_CHAN_INFO_RAW:
+ switch (chan->type) {
+ case IIO_TEMP:
+ ret = adxl355_get_temp_data(data, chan->address);
+ if (ret < 0)
+ return ret;
+ *val = get_unaligned_be16(data->transf_buf);
+
+ return IIO_VAL_INT;
+ case IIO_ACCEL:
+ ret = adxl355_read_axis(data, adxl355_chans[
+ chan->address].data_reg);
+ if (ret < 0)
+ return ret;
+ *val = sign_extend32(ret >> chan->scan_type.shift,
+ chan->scan_type.realbits - 1);
+ return IIO_VAL_INT;
+ default:
+ return -EINVAL;
+ }
+
+ case IIO_CHAN_INFO_SCALE:
+ switch (chan->type) {
+ /*
+ * The datasheet defines an intercept of 1885 LSB at 25 degC
+ * and a slope of -9.05 LSB/C. The following formula can be used
+ * to find the temperature:
+ * Temp = ((RAW - 1885)/(-9.05)) + 25 but this doesn't follow
+ * the format of the IIO which is Temp = (RAW + OFFSET) * SCALE.
+ * Hence using some rearranging we get the scale as -110.497238
+ * and offset as -2111.25
+ */
+ case IIO_TEMP:
+ *val = -110;
+ *val2 = 497238;
+ return IIO_VAL_INT_PLUS_MICRO;
+ /*
+ * At +/- 2g with 20-bit resolution, scale is given in datasheet
+ * as 3.9ug/LSB = 0.0000039 * 9.80665 = 0.00003824593 m/s^2
+ */
+ case IIO_ACCEL:
+ *val = 0;
+ *val2 = 38245;
+ return IIO_VAL_INT_PLUS_NANO;
+ default:
+ return -EINVAL;
+ }
+ case IIO_CHAN_INFO_OFFSET:
+ *val = -2111;
+ *val2 = 250000;
+ return IIO_VAL_INT_PLUS_MICRO;
+ case IIO_CHAN_INFO_CALIBBIAS:
+ *val = sign_extend32(data->calibbias[chan->address], 15);
+ return IIO_VAL_INT;
+ case IIO_CHAN_INFO_SAMP_FREQ:
+ *val = adxl355_odr_table[data->odr][0];
+ *val2 = adxl355_odr_table[data->odr][1];
+ return IIO_VAL_INT_PLUS_MICRO;
+ case IIO_CHAN_INFO_HIGH_PASS_FILTER_3DB_FREQUENCY:
+ *val = data->adxl355_hpf_3db_table[data->hpf_3db][0];
+ *val2 = data->adxl355_hpf_3db_table[data->hpf_3db][1];
+ return IIO_VAL_INT_PLUS_MICRO;
+ default:
+ return -EINVAL;
+ }
+}
+
+static int adxl355_write_raw(struct iio_dev *indio_dev,
+ struct iio_chan_spec const *chan,
+ int val, int val2, long mask)
+{
+ struct adxl355_data *data = iio_priv(indio_dev);
+ int odr_idx, hpf_idx, calibbias;
+
+ switch (mask) {
+ case IIO_CHAN_INFO_SAMP_FREQ:
+ odr_idx = adxl355_find_match(adxl355_odr_table,
+ ARRAY_SIZE(adxl355_odr_table),
+ val, val2);
+ if (odr_idx < 0)
+ return odr_idx;
+
+ return adxl355_set_odr(data, odr_idx);
+ case IIO_CHAN_INFO_HIGH_PASS_FILTER_3DB_FREQUENCY:
+ hpf_idx = adxl355_find_match(data->adxl355_hpf_3db_table,
+ ARRAY_SIZE(data->adxl355_hpf_3db_table),
+ val, val2);
+ if (hpf_idx < 0)
+ return hpf_idx;
+
+ return adxl355_set_hpf_3db(data, hpf_idx);
+ case IIO_CHAN_INFO_CALIBBIAS:
+ calibbias = clamp_t(int, val, S16_MIN, S16_MAX);
+
+ return adxl355_set_calibbias(data, chan->address, calibbias);
+ default:
+ return -EINVAL;
+ }
+}
+
+static int adxl355_read_avail(struct iio_dev *indio_dev,
+ struct iio_chan_spec const *chan,
+ const int **vals, int *type, int *length,
+ long mask)
+{
+ struct adxl355_data *data = iio_priv(indio_dev);
+
+ switch (mask) {
+ case IIO_CHAN_INFO_SAMP_FREQ:
+ *vals = (const int *)adxl355_odr_table;
+ *type = IIO_VAL_INT_PLUS_MICRO;
+ /* Values are stored in a 2D matrix */
+ *length = ARRAY_SIZE(adxl355_odr_table) * 2;
+
+ return IIO_AVAIL_LIST;
+ case IIO_CHAN_INFO_HIGH_PASS_FILTER_3DB_FREQUENCY:
+ *vals = (const int *)data->adxl355_hpf_3db_table;
+ *type = IIO_VAL_INT_PLUS_MICRO;
+ /* Values are stored in a 2D matrix */
+ *length = ARRAY_SIZE(data->adxl355_hpf_3db_table) * 2;
+
+ return IIO_AVAIL_LIST;
+ default:
+ return -EINVAL;
+ }
+}
+
+static const struct iio_info adxl355_info = {
+ .read_raw = adxl355_read_raw,
+ .write_raw = adxl355_write_raw,
+ .read_avail = &adxl355_read_avail
+};
+
+#define ADXL355_ACCEL_CHANNEL(index, reg, axis) { \
+ .type = IIO_ACCEL, \
+ .address = reg, \
+ .modified = 1, \
+ .channel2 = IIO_MOD_##axis, \
+ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \
+ BIT(IIO_CHAN_INFO_CALIBBIAS), \
+ .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE) | \
+ BIT(IIO_CHAN_INFO_SAMP_FREQ) | \
+ BIT(IIO_CHAN_INFO_HIGH_PASS_FILTER_3DB_FREQUENCY), \
+ .info_mask_shared_by_type_available = \
+ BIT(IIO_CHAN_INFO_SAMP_FREQ) | \
+ BIT(IIO_CHAN_INFO_HIGH_PASS_FILTER_3DB_FREQUENCY), \
+ .scan_type = { \
+ .sign = 's', \
+ .realbits = 20, \
+ .storagebits = 32, \
+ .shift = 4, \
+ .endianness = IIO_BE, \
+ } \
+}
+
+static const struct iio_chan_spec adxl355_channels[] = {
+ ADXL355_ACCEL_CHANNEL(0, chan_x, X),
+ ADXL355_ACCEL_CHANNEL(1, chan_y, Y),
+ ADXL355_ACCEL_CHANNEL(2, chan_z, Z),
+ {
+ .type = IIO_TEMP,
+ .address = ADXL355_TEMP2_REG,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
+ BIT(IIO_CHAN_INFO_SCALE) |
+ BIT(IIO_CHAN_INFO_OFFSET),
+ .scan_type = {
+ .sign = 's',
+ .realbits = 12,
+ .storagebits = 16,
+ .endianness = IIO_BE,
+ },
+ }
+};
+
+int adxl355_core_probe(struct device *dev, struct regmap *regmap,
+ const char *name)
+{
+ struct adxl355_data *data;
+ struct iio_dev *indio_dev;
+ int ret;
+
+ indio_dev = devm_iio_device_alloc(dev, sizeof(*data));
+ if (!indio_dev)
+ return -ENOMEM;
+
+ data = iio_priv(indio_dev);
+ data->regmap = regmap;
+ data->dev = dev;
+ data->op_mode = ADXL355_STANDBY;
+ mutex_init(&data->lock);
+
+ indio_dev->name = name;
+ indio_dev->info = &adxl355_info;
+ indio_dev->modes = INDIO_DIRECT_MODE;
+ indio_dev->channels = adxl355_channels;
+ indio_dev->num_channels = ARRAY_SIZE(adxl355_channels);
+
+ ret = adxl355_setup(data);
+ if (ret < 0) {
+ dev_err(dev, "ADXL355 setup failed\n");
+ return ret;
+ }
+
+ return devm_iio_device_register(dev, indio_dev);
+}
+EXPORT_SYMBOL_GPL(adxl355_core_probe);
+
+MODULE_AUTHOR("Puranjay Mohan <[email protected]>");
+MODULE_DESCRIPTION("ADXL355 3-Axis Digital Accelerometer core driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/iio/accel/adxl355_i2c.c b/drivers/iio/accel/adxl355_i2c.c
new file mode 100644
index 000000000..e3070ee81
--- /dev/null
+++ b/drivers/iio/accel/adxl355_i2c.c
@@ -0,0 +1,64 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * ADXL355 3-Axis Digital Accelerometer I2C driver
+ *
+ * Copyright (c) 2021 Puranjay Mohan <[email protected]>
+ */
+
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+#include <linux/regmap.h>
+
+#include "adxl355.h"
+
+static const struct regmap_config adxl355_i2c_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .max_register = 0x2F,
+ .rd_table = &adxl355_readable_regs_tbl,
+ .wr_table = &adxl355_writeable_regs_tbl
+};
+
+static int adxl355_i2c_probe(struct i2c_client *client)
+{
+ struct regmap *regmap;
+
+ regmap = devm_regmap_init_i2c(client, &adxl355_i2c_regmap_config);
+ if (IS_ERR(regmap)) {
+ dev_err(&client->dev, "Error initializing i2c regmap: %ld\n",
+ PTR_ERR(regmap));
+ return PTR_ERR(regmap);
+ }
+
+ return adxl355_core_probe(&client->dev, regmap, client->name);
+}
+
+static const struct i2c_device_id adxl355_i2c_id[] = {
+ { "adxl355", 0 },
+ { }
+};
+
+MODULE_DEVICE_TABLE(i2c, adxl355_i2c_id);
+
+static const struct of_device_id adxl355_of_match[] = {
+ { .compatible = "adi,adxl355" },
+ { }
+};
+
+MODULE_DEVICE_TABLE(of, adxl355_of_match);
+
+static struct i2c_driver adxl355_i2c_driver = {
+ .driver = {
+ .name = "adxl355_i2c",
+ .of_match_table = adxl355_of_match,
+ },
+ .probe_new = adxl355_i2c_probe,
+ .id_table = adxl355_i2c_id,
+};
+
+module_i2c_driver(adxl355_i2c_driver);
+
+MODULE_AUTHOR("Puranjay Mohan <[email protected]>");
+MODULE_DESCRIPTION("ADXL355 3-Axis Digital Accelerometer I2C driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/iio/accel/adxl355_spi.c b/drivers/iio/accel/adxl355_spi.c
new file mode 100644
index 000000000..a16bd1407
--- /dev/null
+++ b/drivers/iio/accel/adxl355_spi.c
@@ -0,0 +1,67 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * ADXL355 3-Axis Digital Accelerometer SPI driver
+ *
+ * Copyright (c) 2021 Puranjay Mohan <[email protected]>
+ */
+
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+#include <linux/regmap.h>
+#include <linux/spi/spi.h>
+
+#include "adxl355.h"
+
+static const struct regmap_config adxl355_spi_regmap_config = {
+ .reg_bits = 7,
+ .pad_bits = 1,
+ .val_bits = 8,
+ .read_flag_mask = BIT(0),
+ .max_register = 0x2F,
+ .rd_table = &adxl355_readable_regs_tbl,
+ .wr_table = &adxl355_writeable_regs_tbl
+};
+
+static int adxl355_spi_probe(struct spi_device *spi)
+{
+ const struct spi_device_id *id = spi_get_device_id(spi);
+ struct regmap *regmap;
+
+ regmap = devm_regmap_init_spi(spi, &adxl355_spi_regmap_config);
+ if (IS_ERR(regmap)) {
+ dev_err(&spi->dev, "Error initializing spi regmap: %ld\n",
+ PTR_ERR(regmap));
+ return PTR_ERR(regmap);
+ }
+
+ return adxl355_core_probe(&spi->dev, regmap, id->name);
+}
+
+static const struct spi_device_id adxl355_spi_id[] = {
+ { "adxl355", 0 },
+ { }
+};
+
+MODULE_DEVICE_TABLE(spi, adxl355_spi_id);
+
+static const struct of_device_id adxl355_of_match[] = {
+ { .compatible = "adi,adxl355" },
+ { }
+};
+
+MODULE_DEVICE_TABLE(of, adxl355_of_match);
+
+static struct spi_driver adxl355_spi_driver = {
+ .driver = {
+ .name = "adxl355_spi",
+ .of_match_table = adxl355_of_match,
+ },
+ .probe = adxl355_spi_probe,
+ .id_table = adxl355_spi_id,
+};
+
+module_spi_driver(adxl355_spi_driver);
+
+MODULE_AUTHOR("Puranjay Mohan <[email protected]>");
+MODULE_DESCRIPTION("ADXL355 3-Axis Digital Accelerometer SPI driver");
+MODULE_LICENSE("GPL v2");
--
2.30.1

2021-08-09 07:47:54

by Puranjay Mohan

[permalink] [raw]
Subject: [PATCH v9 2/2] iio: accel: adxl355: Add triggered buffer support

Provide a way for continuous data capture by setting up buffer support. The
data ready signal exposed at the DRDY pin of the ADXL355 is exploited as
a hardware interrupt which triggers to fill the buffer.

Signed-off-by: Puranjay Mohan <[email protected]>
---
drivers/iio/accel/Kconfig | 4 ++
drivers/iio/accel/adxl355.h | 2 +-
drivers/iio/accel/adxl355_core.c | 102 ++++++++++++++++++++++++++++++-
drivers/iio/accel/adxl355_i2c.c | 3 +-
drivers/iio/accel/adxl355_spi.c | 2 +-
5 files changed, 108 insertions(+), 5 deletions(-)

diff --git a/drivers/iio/accel/Kconfig b/drivers/iio/accel/Kconfig
index d0c45c809..9c16c1841 100644
--- a/drivers/iio/accel/Kconfig
+++ b/drivers/iio/accel/Kconfig
@@ -69,6 +69,8 @@ config ADXL355_I2C
depends on I2C
select ADXL355
select REGMAP_I2C
+ select IIO_BUFFER
+ select IIO_TRIGGERED_BUFFER
help
Say Y here if you want to build i2c support for the Analog Devices
ADXL355 3-axis digital accelerometer.
@@ -82,6 +84,8 @@ config ADXL355_SPI
depends on SPI
select ADXL355
select REGMAP_SPI
+ select IIO_BUFFER
+ select IIO_TRIGGERED_BUFFER
help
Say Y here if you want to build spi support for the Analog Devices
ADXL355 3-axis digital accelerometer.
diff --git a/drivers/iio/accel/adxl355.h b/drivers/iio/accel/adxl355.h
index 322b0abb8..f0a376e6d 100644
--- a/drivers/iio/accel/adxl355.h
+++ b/drivers/iio/accel/adxl355.h
@@ -15,5 +15,5 @@ extern const struct regmap_access_table adxl355_readable_regs_tbl;
extern const struct regmap_access_table adxl355_writeable_regs_tbl;

int adxl355_core_probe(struct device *dev, struct regmap *regmap,
- const char *name);
+ const char *name, int irq);
#endif /* _ADXL355_H_ */
diff --git a/drivers/iio/accel/adxl355_core.c b/drivers/iio/accel/adxl355_core.c
index d1163cde1..45397dcce 100644
--- a/drivers/iio/accel/adxl355_core.c
+++ b/drivers/iio/accel/adxl355_core.c
@@ -9,6 +9,10 @@

#include <asm/unaligned.h>
#include <linux/bitfield.h>
+#include <linux/iio/buffer.h>
+#include <linux/iio/trigger.h>
+#include <linux/iio/triggered_buffer.h>
+#include <linux/iio/trigger_consumer.h>
#include <linux/iio/iio.h>
#include <linux/limits.h>
#include <linux/math64.h>
@@ -153,6 +157,7 @@ static const struct adxl355_chan_info adxl355_chans[] = {
};

struct adxl355_data {
+ int irq;
struct regmap *regmap;
struct device *dev;
struct mutex lock; /* lock to protect op_mode */
@@ -162,6 +167,12 @@ struct adxl355_data {
int calibbias[3];
int adxl355_hpf_3db_table[7][2];
u8 transf_buf[3] ____cacheline_aligned;
+ struct iio_trigger *dready_trig;
+ /* Ensure correct alignment of timestamp when present */
+ struct {
+ __be32 channels[3];
+ s64 ts;
+ } buffer ____cacheline_aligned;
};

static int adxl355_set_op_mode(struct adxl355_data *data,
@@ -493,12 +504,46 @@ static int adxl355_read_avail(struct iio_dev *indio_dev,
}
}

+static const unsigned long adxl355_avail_scan_masks[] = {
+ GENMASK(3, 0),
+ 0
+};
+
static const struct iio_info adxl355_info = {
.read_raw = adxl355_read_raw,
.write_raw = adxl355_write_raw,
.read_avail = &adxl355_read_avail
};

+static const struct iio_trigger_ops adxl355_trigger_ops = {
+ .validate_device = &iio_trigger_validate_own_device,
+};
+
+static irqreturn_t adxl355_trigger_handler(int irq, void *p)
+{
+ struct iio_poll_func *pf = p;
+ struct iio_dev *indio_dev = pf->indio_dev;
+ struct adxl355_data *data = iio_priv(indio_dev);
+ int ret;
+
+ mutex_lock(&data->lock);
+
+ ret = regmap_bulk_read(data->regmap, ADXL355_XDATA3_REG,
+ data->buffer.channels,
+ 9);
+ if (ret)
+ goto out_unlock_notify;
+
+ iio_push_to_buffers_with_timestamp(indio_dev, &data->buffer,
+ pf->timestamp);
+
+out_unlock_notify:
+ mutex_unlock(&data->lock);
+ iio_trigger_notify_done(indio_dev->trig);
+
+ return IRQ_HANDLED;
+}
+
#define ADXL355_ACCEL_CHANNEL(index, reg, axis) { \
.type = IIO_ACCEL, \
.address = reg, \
@@ -512,6 +557,7 @@ static const struct iio_info adxl355_info = {
.info_mask_shared_by_type_available = \
BIT(IIO_CHAN_INFO_SAMP_FREQ) | \
BIT(IIO_CHAN_INFO_HIGH_PASS_FILTER_3DB_FREQUENCY), \
+ .scan_index = index, \
.scan_type = { \
.sign = 's', \
.realbits = 20, \
@@ -531,17 +577,56 @@ static const struct iio_chan_spec adxl355_channels[] = {
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
BIT(IIO_CHAN_INFO_SCALE) |
BIT(IIO_CHAN_INFO_OFFSET),
+ .scan_index = 3,
.scan_type = {
.sign = 's',
.realbits = 12,
.storagebits = 16,
.endianness = IIO_BE,
},
- }
+ },
+ IIO_CHAN_SOFT_TIMESTAMP(4)
};

+static int adxl355_probe_trigger(struct iio_dev *indio_dev)
+{
+ struct adxl355_data *data = iio_priv(indio_dev);
+ int ret;
+
+ if (!data->irq) {
+ dev_info(data->dev, "no irq, using polling\n");
+ return 0;
+ }
+
+ data->dready_trig = devm_iio_trigger_alloc(data->dev, "%s-dev%d",
+ indio_dev->name,
+ indio_dev->id);
+ if (!data->dready_trig)
+ return -ENOMEM;
+
+ data->dready_trig->ops = &adxl355_trigger_ops;
+ iio_trigger_set_drvdata(data->dready_trig, indio_dev);
+
+ ret = devm_request_irq(data->dev, data->irq,
+ &iio_trigger_generic_data_rdy_poll,
+ IRQF_ONESHOT, "adxl355_irq", data->dready_trig);
+ if (ret < 0)
+ return dev_err_probe(data->dev, ret, "request irq %d failed\n",
+ data->irq);
+
+ ret = devm_iio_trigger_register(data->dev, data->dready_trig);
+ if (ret) {
+ dev_err(data->dev, "iio trigger register failed\n");
+ return ret;
+ }
+
+ indio_dev->trig = iio_trigger_get(data->dready_trig);
+
+ return 0;
+}
+
int adxl355_core_probe(struct device *dev, struct regmap *regmap,
- const char *name)
+ const char *name, int irq)
{
struct adxl355_data *data;
struct iio_dev *indio_dev;
@@ -554,6 +639,7 @@ int adxl355_core_probe(struct device *dev, struct regmap *regmap,
data = iio_priv(indio_dev);
data->regmap = regmap;
data->dev = dev;
+ data->irq = irq;
data->op_mode = ADXL355_STANDBY;
mutex_init(&data->lock);

@@ -562,6 +648,7 @@ int adxl355_core_probe(struct device *dev, struct regmap *regmap,
indio_dev->modes = INDIO_DIRECT_MODE;
indio_dev->channels = adxl355_channels;
indio_dev->num_channels = ARRAY_SIZE(adxl355_channels);
+ indio_dev->available_scan_masks = adxl355_avail_scan_masks;

ret = adxl355_setup(data);
if (ret < 0) {
@@ -569,6 +656,17 @@ int adxl355_core_probe(struct device *dev, struct regmap *regmap,
return ret;
}

+ ret = devm_iio_triggered_buffer_setup(dev, indio_dev,
+ &iio_pollfunc_store_time,
+ &adxl355_trigger_handler, NULL);
+ if (ret < 0)
+ return dev_err_probe(dev, ret,
+ "iio triggered buffer setup failed\n");
+
+ ret = adxl355_probe_trigger(indio_dev);
+ if (ret < 0)
+ return ret;
+
return devm_iio_device_register(dev, indio_dev);
}
EXPORT_SYMBOL_GPL(adxl355_core_probe);
diff --git a/drivers/iio/accel/adxl355_i2c.c b/drivers/iio/accel/adxl355_i2c.c
index e3070ee81..c18521819 100644
--- a/drivers/iio/accel/adxl355_i2c.c
+++ b/drivers/iio/accel/adxl355_i2c.c
@@ -31,7 +31,8 @@ static int adxl355_i2c_probe(struct i2c_client *client)
return PTR_ERR(regmap);
}

- return adxl355_core_probe(&client->dev, regmap, client->name);
+ return adxl355_core_probe(&client->dev, regmap, client->name,
+ client->irq);
}

static const struct i2c_device_id adxl355_i2c_id[] = {
diff --git a/drivers/iio/accel/adxl355_spi.c b/drivers/iio/accel/adxl355_spi.c
index a16bd1407..f9ba153f6 100644
--- a/drivers/iio/accel/adxl355_spi.c
+++ b/drivers/iio/accel/adxl355_spi.c
@@ -34,7 +34,7 @@ static int adxl355_spi_probe(struct spi_device *spi)
return PTR_ERR(regmap);
}

- return adxl355_core_probe(&spi->dev, regmap, id->name);
+ return adxl355_core_probe(&spi->dev, regmap, id->name, spi->irq);
}

static const struct spi_device_id adxl355_spi_id[] = {
--
2.30.1

2021-08-09 07:50:42

by Puranjay Mohan

[permalink] [raw]
Subject: Re: [PATCH v9 2/2] iio: accel: adxl355: Add triggered buffer support

Please ignore this patch.
It was sent by mistake, it is not supposed to be a part of this series.

On Mon, Aug 9, 2021 at 1:15 PM Puranjay Mohan <[email protected]> wrote:
>
> Provide a way for continuous data capture by setting up buffer support. The
> data ready signal exposed at the DRDY pin of the ADXL355 is exploited as
> a hardware interrupt which triggers to fill the buffer.
>
> Signed-off-by: Puranjay Mohan <[email protected]>
> ---
> drivers/iio/accel/Kconfig | 4 ++
> drivers/iio/accel/adxl355.h | 2 +-
> drivers/iio/accel/adxl355_core.c | 102 ++++++++++++++++++++++++++++++-
> drivers/iio/accel/adxl355_i2c.c | 3 +-
> drivers/iio/accel/adxl355_spi.c | 2 +-
> 5 files changed, 108 insertions(+), 5 deletions(-)
>
> diff --git a/drivers/iio/accel/Kconfig b/drivers/iio/accel/Kconfig
> index d0c45c809..9c16c1841 100644
> --- a/drivers/iio/accel/Kconfig
> +++ b/drivers/iio/accel/Kconfig
> @@ -69,6 +69,8 @@ config ADXL355_I2C
> depends on I2C
> select ADXL355
> select REGMAP_I2C
> + select IIO_BUFFER
> + select IIO_TRIGGERED_BUFFER
> help
> Say Y here if you want to build i2c support for the Analog Devices
> ADXL355 3-axis digital accelerometer.
> @@ -82,6 +84,8 @@ config ADXL355_SPI
> depends on SPI
> select ADXL355
> select REGMAP_SPI
> + select IIO_BUFFER
> + select IIO_TRIGGERED_BUFFER
> help
> Say Y here if you want to build spi support for the Analog Devices
> ADXL355 3-axis digital accelerometer.
> diff --git a/drivers/iio/accel/adxl355.h b/drivers/iio/accel/adxl355.h
> index 322b0abb8..f0a376e6d 100644
> --- a/drivers/iio/accel/adxl355.h
> +++ b/drivers/iio/accel/adxl355.h
> @@ -15,5 +15,5 @@ extern const struct regmap_access_table adxl355_readable_regs_tbl;
> extern const struct regmap_access_table adxl355_writeable_regs_tbl;
>
> int adxl355_core_probe(struct device *dev, struct regmap *regmap,
> - const char *name);
> + const char *name, int irq);
> #endif /* _ADXL355_H_ */
> diff --git a/drivers/iio/accel/adxl355_core.c b/drivers/iio/accel/adxl355_core.c
> index d1163cde1..45397dcce 100644
> --- a/drivers/iio/accel/adxl355_core.c
> +++ b/drivers/iio/accel/adxl355_core.c
> @@ -9,6 +9,10 @@
>
> #include <asm/unaligned.h>
> #include <linux/bitfield.h>
> +#include <linux/iio/buffer.h>
> +#include <linux/iio/trigger.h>
> +#include <linux/iio/triggered_buffer.h>
> +#include <linux/iio/trigger_consumer.h>
> #include <linux/iio/iio.h>
> #include <linux/limits.h>
> #include <linux/math64.h>
> @@ -153,6 +157,7 @@ static const struct adxl355_chan_info adxl355_chans[] = {
> };
>
> struct adxl355_data {
> + int irq;
> struct regmap *regmap;
> struct device *dev;
> struct mutex lock; /* lock to protect op_mode */
> @@ -162,6 +167,12 @@ struct adxl355_data {
> int calibbias[3];
> int adxl355_hpf_3db_table[7][2];
> u8 transf_buf[3] ____cacheline_aligned;
> + struct iio_trigger *dready_trig;
> + /* Ensure correct alignment of timestamp when present */
> + struct {
> + __be32 channels[3];
> + s64 ts;
> + } buffer ____cacheline_aligned;
> };
>
> static int adxl355_set_op_mode(struct adxl355_data *data,
> @@ -493,12 +504,46 @@ static int adxl355_read_avail(struct iio_dev *indio_dev,
> }
> }
>
> +static const unsigned long adxl355_avail_scan_masks[] = {
> + GENMASK(3, 0),
> + 0
> +};
> +
> static const struct iio_info adxl355_info = {
> .read_raw = adxl355_read_raw,
> .write_raw = adxl355_write_raw,
> .read_avail = &adxl355_read_avail
> };
>
> +static const struct iio_trigger_ops adxl355_trigger_ops = {
> + .validate_device = &iio_trigger_validate_own_device,
> +};
> +
> +static irqreturn_t adxl355_trigger_handler(int irq, void *p)
> +{
> + struct iio_poll_func *pf = p;
> + struct iio_dev *indio_dev = pf->indio_dev;
> + struct adxl355_data *data = iio_priv(indio_dev);
> + int ret;
> +
> + mutex_lock(&data->lock);
> +
> + ret = regmap_bulk_read(data->regmap, ADXL355_XDATA3_REG,
> + data->buffer.channels,
> + 9);
> + if (ret)
> + goto out_unlock_notify;
> +
> + iio_push_to_buffers_with_timestamp(indio_dev, &data->buffer,
> + pf->timestamp);
> +
> +out_unlock_notify:
> + mutex_unlock(&data->lock);
> + iio_trigger_notify_done(indio_dev->trig);
> +
> + return IRQ_HANDLED;
> +}
> +
> #define ADXL355_ACCEL_CHANNEL(index, reg, axis) { \
> .type = IIO_ACCEL, \
> .address = reg, \
> @@ -512,6 +557,7 @@ static const struct iio_info adxl355_info = {
> .info_mask_shared_by_type_available = \
> BIT(IIO_CHAN_INFO_SAMP_FREQ) | \
> BIT(IIO_CHAN_INFO_HIGH_PASS_FILTER_3DB_FREQUENCY), \
> + .scan_index = index, \
> .scan_type = { \
> .sign = 's', \
> .realbits = 20, \
> @@ -531,17 +577,56 @@ static const struct iio_chan_spec adxl355_channels[] = {
> .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
> BIT(IIO_CHAN_INFO_SCALE) |
> BIT(IIO_CHAN_INFO_OFFSET),
> + .scan_index = 3,
> .scan_type = {
> .sign = 's',
> .realbits = 12,
> .storagebits = 16,
> .endianness = IIO_BE,
> },
> - }
> + },
> + IIO_CHAN_SOFT_TIMESTAMP(4)
> };
>
> +static int adxl355_probe_trigger(struct iio_dev *indio_dev)
> +{
> + struct adxl355_data *data = iio_priv(indio_dev);
> + int ret;
> +
> + if (!data->irq) {
> + dev_info(data->dev, "no irq, using polling\n");
> + return 0;
> + }
> +
> + data->dready_trig = devm_iio_trigger_alloc(data->dev, "%s-dev%d",
> + indio_dev->name,
> + indio_dev->id);
> + if (!data->dready_trig)
> + return -ENOMEM;
> +
> + data->dready_trig->ops = &adxl355_trigger_ops;
> + iio_trigger_set_drvdata(data->dready_trig, indio_dev);
> +
> + ret = devm_request_irq(data->dev, data->irq,
> + &iio_trigger_generic_data_rdy_poll,
> + IRQF_ONESHOT, "adxl355_irq", data->dready_trig);
> + if (ret < 0)
> + return dev_err_probe(data->dev, ret, "request irq %d failed\n",
> + data->irq);
> +
> + ret = devm_iio_trigger_register(data->dev, data->dready_trig);
> + if (ret) {
> + dev_err(data->dev, "iio trigger register failed\n");
> + return ret;
> + }
> +
> + indio_dev->trig = iio_trigger_get(data->dready_trig);
> +
> + return 0;
> +}
> +
> int adxl355_core_probe(struct device *dev, struct regmap *regmap,
> - const char *name)
> + const char *name, int irq)
> {
> struct adxl355_data *data;
> struct iio_dev *indio_dev;
> @@ -554,6 +639,7 @@ int adxl355_core_probe(struct device *dev, struct regmap *regmap,
> data = iio_priv(indio_dev);
> data->regmap = regmap;
> data->dev = dev;
> + data->irq = irq;
> data->op_mode = ADXL355_STANDBY;
> mutex_init(&data->lock);
>
> @@ -562,6 +648,7 @@ int adxl355_core_probe(struct device *dev, struct regmap *regmap,
> indio_dev->modes = INDIO_DIRECT_MODE;
> indio_dev->channels = adxl355_channels;
> indio_dev->num_channels = ARRAY_SIZE(adxl355_channels);
> + indio_dev->available_scan_masks = adxl355_avail_scan_masks;
>
> ret = adxl355_setup(data);
> if (ret < 0) {
> @@ -569,6 +656,17 @@ int adxl355_core_probe(struct device *dev, struct regmap *regmap,
> return ret;
> }
>
> + ret = devm_iio_triggered_buffer_setup(dev, indio_dev,
> + &iio_pollfunc_store_time,
> + &adxl355_trigger_handler, NULL);
> + if (ret < 0)
> + return dev_err_probe(dev, ret,
> + "iio triggered buffer setup failed\n");
> +
> + ret = adxl355_probe_trigger(indio_dev);
> + if (ret < 0)
> + return ret;
> +
> return devm_iio_device_register(dev, indio_dev);
> }
> EXPORT_SYMBOL_GPL(adxl355_core_probe);
> diff --git a/drivers/iio/accel/adxl355_i2c.c b/drivers/iio/accel/adxl355_i2c.c
> index e3070ee81..c18521819 100644
> --- a/drivers/iio/accel/adxl355_i2c.c
> +++ b/drivers/iio/accel/adxl355_i2c.c
> @@ -31,7 +31,8 @@ static int adxl355_i2c_probe(struct i2c_client *client)
> return PTR_ERR(regmap);
> }
>
> - return adxl355_core_probe(&client->dev, regmap, client->name);
> + return adxl355_core_probe(&client->dev, regmap, client->name,
> + client->irq);
> }
>
> static const struct i2c_device_id adxl355_i2c_id[] = {
> diff --git a/drivers/iio/accel/adxl355_spi.c b/drivers/iio/accel/adxl355_spi.c
> index a16bd1407..f9ba153f6 100644
> --- a/drivers/iio/accel/adxl355_spi.c
> +++ b/drivers/iio/accel/adxl355_spi.c
> @@ -34,7 +34,7 @@ static int adxl355_spi_probe(struct spi_device *spi)
> return PTR_ERR(regmap);
> }
>
> - return adxl355_core_probe(&spi->dev, regmap, id->name);
> + return adxl355_core_probe(&spi->dev, regmap, id->name, spi->irq);
> }
>
> static const struct spi_device_id adxl355_spi_id[] = {
> --
> 2.30.1
>


--
Thanks and Regards

Yours Truly,

Puranjay Mohan

2021-08-09 07:54:10

by Puranjay Mohan

[permalink] [raw]
Subject: Re: [PATCH v9 0/2] iio: accel: add support for ADXL355

Please Ignore this I will resend this properly.
I made some mistakes while sending the patches.
I am really sorry for the noise.

On Mon, Aug 9, 2021 at 1:15 PM Puranjay Mohan <[email protected]> wrote:
>
> Add the dt-bindings and the driver for ADXL355 3-axis MEMS Accelerometer.
>
> Changes since v8:
> 1. Make scale and offset defines inline and remove them.
> 2. Change dt-binding doc to state interrupt polarity only for DRDY pin.
> 3. Remove triggered buffer support from this patch series.
>
> Changes since v7:
> 1. Update MAINTAINERS to show all driver files.
> 2. Set CONFIGS for buffered support in Kconfig.
>
> Changes since v6:
> 1. Use interrupt-names property in device tree document.
> 2. Add triggered buffer support.
> 3. Use a static table for offset and data registers.
> 4. Fix coding style issues.
> 5. move defines from header to c file.
>
> Changes since v5:
> 1. Used get_unaligned_be24() and get_unaligned_be16() to parse
> acceleration and temperature data. This solves sparse errors and also
> make the code more understandable.
>
> Changes since v4:
> 1. Fix errors reported by sparse.
>
> Changes since v3:
> 1. Fix errors in yaml DT doc.
> 2. Change SPDX-License-Identifier to GPL-2.0-only OR BSD-2-Clause
>
> Changes since v2:
> 1. Add separate DT binding doc in yaml.
> 2. Use ____cacheline_aligned buffer for regmap_bulk_read/write calls.
> 3. Make code consistent by using same style in switch case.
> 4. Use FIELD_PREP in place of custom macros.
> 5. Make Kconfig description more informative.
>
> Changes since v1:
> 1. Remove the declarations for static regmap structures from adxl355.h.
> This was missed in the v1 and caused errors.
> 2. Make switch case statements consistent by directly returning from
> each case rather than saving the return in a variable.
> 3. Some coding style changes.
>
> Changes since v0:
> 1. Move adxl355_hpf_3db_table to adxl355_data structure. This is done to make
> sure that each device gets its own table.
> 2. Make local regmap definitions private to adxl355_core.c.
> 3. Other minor coding style changes.
>
> Puranjay Mohan (2):
> iio: accel: Add driver support for ADXL355
> iio: accel: adxl355: Add triggered buffer support
>
> MAINTAINERS | 10 +
> drivers/iio/accel/Kconfig | 33 ++
> drivers/iio/accel/Makefile | 3 +
> drivers/iio/accel/adxl355.h | 19 +
> drivers/iio/accel/adxl355_core.c | 676 +++++++++++++++++++++++++++++++
> drivers/iio/accel/adxl355_i2c.c | 65 +++
> drivers/iio/accel/adxl355_spi.c | 67 +++
> 7 files changed, 873 insertions(+)
> create mode 100644 drivers/iio/accel/adxl355.h
> create mode 100644 drivers/iio/accel/adxl355_core.c
> create mode 100644 drivers/iio/accel/adxl355_i2c.c
> create mode 100644 drivers/iio/accel/adxl355_spi.c
>
> --
> 2.30.1
>


--
Thanks and Regards

Yours Truly,

Puranjay Mohan

2021-08-10 16:31:55

by Andy Shevchenko

[permalink] [raw]
Subject: Re: [PATCH v9 1/2] iio: accel: Add driver support for ADXL355

On Mon, Aug 9, 2021 at 10:46 AM Puranjay Mohan <[email protected]> wrote:
>
> ADXL355 is 3-axis MEMS Accelerometer. It offers low noise density,

is a 3-axis

> low 0g offset drift, low power with selectable measurement ranges.
> It also features programmable high-pass and low-pass filters.

...

> +F: drivers/iio/accel/adxl355.h
> +F: drivers/iio/accel/adxl355_core.c
> +F: drivers/iio/accel/adxl355_i2c.c
> +F: drivers/iio/accel/adxl355_spi.c
> +F: Documentation/devicetree/bindings/iio/accel/adi,adxl355.yaml

Have you run checkpatch?

...

> +#ifndef _ADXL355_H_
> +#define _ADXL355_H_
> +
> +#include <linux/regmap.h>

Missed declaration for struct device.

> +extern const struct regmap_access_table adxl355_readable_regs_tbl;
> +

I think you may drop this blank line.

> +extern const struct regmap_access_table adxl355_writeable_regs_tbl;
> +
> +int adxl355_core_probe(struct device *dev, struct regmap *regmap,
> + const char *name);

+ blank line?

> +#endif /* _ADXL355_H_ */

...

> +#include <asm/unaligned.h>

asm/* is less generic, can you move it after linux/*?

> +#include <linux/bitfield.h>

Does this imply bits.h? If not, add the latter.

> +#include <linux/iio/iio.h>
> +#include <linux/limits.h>
> +#include <linux/math64.h>
> +#include <linux/module.h>
> +#include <linux/mod_devicetable.h>
> +#include <linux/regmap.h>

...

> +static const struct regmap_range adxl355_read_reg_range[] = {
> + regmap_reg_range(ADXL355_DEVID_AD_REG, ADXL355_FIFO_DATA_REG),
> + regmap_reg_range(ADXL355_OFFSET_X_H_REG, ADXL355_SELF_TEST_REG)

Leave commas in non-terminator lines.

> +};

...

> +static const struct regmap_range adxl355_write_reg_range[] = {
> + regmap_reg_range(ADXL355_OFFSET_X_H_REG, ADXL355_RESET_REG)

Ditto.

> +};

...

> +enum adxl355_op_mode {

> + ADXL355_TEMP_OFF

Ditto.

> +};
> +
> +enum adxl355_odr {

> + ADXL355_ODR_3_906HZ

Ditto.

> +};
> +
> +enum adxl355_hpf_3db {

> + ADXL355_HPF_0_0238

Ditto.

> +};
> +
> +static const int adxl355_odr_table[][2] = {

> + [10] = {3, 906000}

Ditto.

> +};
> +
> +static const int adxl355_hpf_3db_multipliers[] = {

> + 238

Ditto.

> +};
> +
> +enum adxl355_chans {
> + chan_x, chan_y, chan_z

Ditto.

> +};

> +static const struct adxl355_chan_info adxl355_chans[] = {

> + [chan_z] = {
> + .data_reg = ADXL355_ZDATA3_REG,
> + .offset_reg = ADXL355_OFFSET_Z_H_REG
> + }

Ditto.

> +};

To avoid adding extra entries, consider using static_assert():s.

...

> +static void adxl355_fill_3db_frequency_table(struct adxl355_data *data)
> +{
> + int i;
> + u64 rem;
> + u64 div;
> + u32 multiplier;

Reversed xmas tree order?

> + u64 odr = mul_u64_u32_shr(adxl355_odr_table[data->odr][0], 1000000, 0) +
> + adxl355_odr_table[data->odr][1];

Split definition and assignment.

> + for (i = 0; i < ARRAY_SIZE(adxl355_hpf_3db_multipliers); i++) {
> + multiplier = adxl355_hpf_3db_multipliers[i];
> + div = div64_u64_rem(mul_u64_u32_shr(odr, multiplier, 0),
> + 100000000000000UL, &rem);
> +
> + data->adxl355_hpf_3db_table[i][0] = div;
> + data->adxl355_hpf_3db_table[i][1] = div_u64(rem, 100000000);
> + }

Do all those power-of-ten constants have a meaning? Shouldn't it be
better to use named definitions?

> +}

...

> + /*
> + * Perform a software reset to make sure the device is in a consistent
> + * state after start up.

start-up

> + */

...

> + ret = regmap_bulk_read(data->regmap, addr, data->transf_buf, 3);

ARRAY_SIZE() ?

> + if (ret < 0)
> + return ret;

...

> + /*
> + * The datasheet defines an intercept of 1885 LSB at 25 degC
> + * and a slope of -9.05 LSB/C. The following formula can be used
> + * to find the temperature:
> + * Temp = ((RAW - 1885)/(-9.05)) + 25 but this doesn't follow
> + * the format of the IIO which is Temp = (RAW + OFFSET) * SCALE.
> + * Hence using some rearranging we get the scale as -110.497238
> + * and offset as -2111.25

Missed period.

> + */

...

> + /*
> + * At +/- 2g with 20-bit resolution, scale is given in datasheet
> + * as 3.9ug/LSB = 0.0000039 * 9.80665 = 0.00003824593 m/s^2

Ditto for all multi-line comments.

> + */

...

> +static const struct regmap_config adxl355_i2c_regmap_config = {
> + .reg_bits = 8,
> + .val_bits = 8,
> + .max_register = 0x2F,
> + .rd_table = &adxl355_readable_regs_tbl,
> + .wr_table = &adxl355_writeable_regs_tbl

+ comma

> +};

...

> + regmap = devm_regmap_init_i2c(client, &adxl355_i2c_regmap_config);
> + if (IS_ERR(regmap)) {
> + dev_err(&client->dev, "Error initializing i2c regmap: %ld\n",
> + PTR_ERR(regmap));

One line?

> + return PTR_ERR(regmap);
> + }

...

> +static const struct i2c_device_id adxl355_i2c_id[] = {
> + { "adxl355", 0 },
> + { }
> +};

> +

Redundant blank line.

> +MODULE_DEVICE_TABLE(i2c, adxl355_i2c_id);
> +
> +static const struct of_device_id adxl355_of_match[] = {
> + { .compatible = "adi,adxl355" },
> + { }
> +};

> +

Ditto.

> +MODULE_DEVICE_TABLE(of, adxl355_of_match);
> +
> +static struct i2c_driver adxl355_i2c_driver = {
> + .driver = {
> + .name = "adxl355_i2c",
> + .of_match_table = adxl355_of_match,
> + },
> + .probe_new = adxl355_i2c_probe,
> + .id_table = adxl355_i2c_id,
> +};

> +

Ditto.

> +module_i2c_driver(adxl355_i2c_driver);

For SPI part the very same bunch of comments.

--
With Best Regards,
Andy Shevchenko