From: Maxim Sloyko <[email protected]>
Add the pmbus driver for the Infineon ir38064 voltage regulator.
Signed-off-by: Maxim Sloyko <[email protected]>
Signed-off-by: Patrick Venture <[email protected]>
---
v2:
- Cleaned up weird tabbing behavior in doc.
v1:
- Initial patchset.
---
Documentation/hwmon/ir38064 | 64 +++++++++++++++++++++++++++++++++++
drivers/hwmon/pmbus/Kconfig | 9 +++++
drivers/hwmon/pmbus/Makefile | 1 +
drivers/hwmon/pmbus/ir38064.c | 60 ++++++++++++++++++++++++++++++++
4 files changed, 134 insertions(+)
create mode 100644 Documentation/hwmon/ir38064
create mode 100644 drivers/hwmon/pmbus/ir38064.c
diff --git a/Documentation/hwmon/ir38064 b/Documentation/hwmon/ir38064
new file mode 100644
index 0000000000000..618779a329da0
--- /dev/null
+++ b/Documentation/hwmon/ir38064
@@ -0,0 +1,64 @@
+Kernel driver ir38064
+=====================
+
+Supported chips:
+ * Infineon IR38064
+ Prefix: 'ir38064'
+ Addresses scanned: -
+ Datasheet: Publicly available at the Infineon webiste
+ https://www.infineon.com/dgdl/Infineon-IR38064MTRPBF-DS-v03_07-EN.pdf?fileId=5546d462584d1d4a0158db0d9efb67ca
+
+Datasheet is not publicly available.
+
+
+Authors:
+ Maxim Sloyko <[email protected]>
+ Patrick Venture <[email protected]>
+
+Description
+-----------
+
+IR38064 is a Single-input Voltage, Synchronous Buck Regulator, DC-DC Converter.
+
+Usage Notes
+-----------
+
+This driver does not probe for PMBus devices. You will have to instantiate
+devices explicitly.
+
+Sysfs attributes
+----------------
+
+curr1_label "iout1"
+curr1_input Measured output current
+curr1_crit Critical maximum current
+curr1_crit_alarm Current critical high alarm
+curr1_max Maximum current
+curr1_max_alarm Current high alarm
+
+in1_label "vin"
+in1_input Measured input voltage
+in1_crit Critical maximum input voltage
+in1_crit_alarm Input voltage critical high alarm
+in1_min Minimum input voltage
+in1_min_alarm Input voltage low alarm
+
+in2_label "vout1"
+in2_input Measured output voltage
+in2_lcrit Critical minimum output voltage
+in2_lcrit_alarm Output voltage critical low alarm
+in2_crit Critical maximum output voltage
+in2_crit_alarm Output voltage critical high alarm
+in2_max Maximum output voltage
+in2_max_alarm Output voltage high alarm
+in2_min Minimum output voltage
+in2_min_alarm Output voltage low alarm
+
+power1_label "pout1"
+power1_input Measured output power
+
+temp1_input Measured temperature
+temp1_crit Critical high temperature
+temp1_crit_alarm Chip temperature critical high alarm
+temp1_max Maximum temperature
+temp1_max_alarm Chip temperature high alarm
diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig
index 629cb45f8557a..de87abab990e5 100644
--- a/drivers/hwmon/pmbus/Kconfig
+++ b/drivers/hwmon/pmbus/Kconfig
@@ -54,6 +54,15 @@ config SENSORS_IR35221
This driver can also be built as a module. If so, the module will
be called ir35521.
+config SENSORS_IR38064
+ tristate "Infineon IR38064"
+ help
+ If you say yes here you get hardware monitoring support for Infineon
+ IR38064.
+
+ This driver can also be built as a module. If so, the module will
+ be called ir38064.
+
config SENSORS_LM25066
tristate "National Semiconductor LM25066 and compatibles"
help
diff --git a/drivers/hwmon/pmbus/Makefile b/drivers/hwmon/pmbus/Makefile
index ea0e39518c216..7d1fa6b3c8c93 100644
--- a/drivers/hwmon/pmbus/Makefile
+++ b/drivers/hwmon/pmbus/Makefile
@@ -8,6 +8,7 @@ obj-$(CONFIG_SENSORS_PMBUS) += pmbus.o
obj-$(CONFIG_SENSORS_ADM1275) += adm1275.o
obj-$(CONFIG_SENSORS_IBM_CFFPS) += ibm-cffps.o
obj-$(CONFIG_SENSORS_IR35221) += ir35221.o
+obj-$(CONFIG_SENSORS_IR38064) += ir38064.o
obj-$(CONFIG_SENSORS_LM25066) += lm25066.o
obj-$(CONFIG_SENSORS_LTC2978) += ltc2978.o
obj-$(CONFIG_SENSORS_LTC3815) += ltc3815.o
diff --git a/drivers/hwmon/pmbus/ir38064.c b/drivers/hwmon/pmbus/ir38064.c
new file mode 100644
index 0000000000000..4b957ebb6fa71
--- /dev/null
+++ b/drivers/hwmon/pmbus/ir38064.c
@@ -0,0 +1,60 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Hardware monitoring driver for Infineon IR38064
+ *
+ * Copyright (c) 2017 Google Inc
+ *
+ */
+
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include "pmbus.h"
+
+static struct pmbus_driver_info ir38064_info = {
+ .pages = 1,
+ .format[PSC_VOLTAGE_IN] = linear,
+ .format[PSC_VOLTAGE_OUT] = direct,
+ .format[PSC_CURRENT_OUT] = linear,
+ .format[PSC_POWER] = linear,
+ .format[PSC_TEMPERATURE] = linear,
+ .m[PSC_VOLTAGE_OUT] = 256,
+ .b[PSC_VOLTAGE_OUT] = 0,
+ .R[PSC_VOLTAGE_OUT] = 0,
+ .func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_STATUS_INPUT
+ | PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP
+ | PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT
+ | PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT
+ | PMBUS_HAVE_POUT,
+};
+
+static int ir38064_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ return pmbus_do_probe(client, id, &ir38064_info);
+}
+
+static const struct i2c_device_id ir38064_id[] = {
+ {"ir38064", 0},
+ {}
+};
+
+MODULE_DEVICE_TABLE(i2c, ir38064_id);
+
+/* This is the driver that will be inserted */
+static struct i2c_driver ir38064_driver = {
+ .driver = {
+ .name = "ir38064",
+ },
+ .probe = ir38064_probe,
+ .remove = pmbus_do_remove,
+ .id_table = ir38064_id,
+};
+
+module_i2c_driver(ir38064_driver);
+
+MODULE_AUTHOR("Maxim Sloyko <[email protected]>");
+MODULE_DESCRIPTION("PMBus driver for Infineon IR38064");
+MODULE_LICENSE("GPL");
--
2.21.0.392.gf8f6787159e-goog
On 4/12/19 12:43 PM, Patrick Venture wrote:
> From: Maxim Sloyko <[email protected]>
>
> Add the pmbus driver for the Infineon ir38064 voltage regulator.
>
> Signed-off-by: Maxim Sloyko <[email protected]>
> Signed-off-by: Patrick Venture <[email protected]>
> ---
> v2:
> - Cleaned up weird tabbing behavior in doc.
> v1:
> - Initial patchset.
> ---
> Documentation/hwmon/ir38064 | 64 +++++++++++++++++++++++++++++++++++
> drivers/hwmon/pmbus/Kconfig | 9 +++++
> drivers/hwmon/pmbus/Makefile | 1 +
> drivers/hwmon/pmbus/ir38064.c | 60 ++++++++++++++++++++++++++++++++
> 4 files changed, 134 insertions(+)
> create mode 100644 Documentation/hwmon/ir38064
> create mode 100644 drivers/hwmon/pmbus/ir38064.c
>
> diff --git a/Documentation/hwmon/ir38064 b/Documentation/hwmon/ir38064
> new file mode 100644
> index 0000000000000..618779a329da0
> --- /dev/null
> +++ b/Documentation/hwmon/ir38064
> @@ -0,0 +1,64 @@
> +Kernel driver ir38064
> +=====================
> +
> +Supported chips:
> + * Infineon IR38064
> + Prefix: 'ir38064'
> + Addresses scanned: -
> + Datasheet: Publicly available at the Infineon webiste
> + https://www.infineon.com/dgdl/Infineon-IR38064MTRPBF-DS-v03_07-EN.pdf?fileId=5546d462584d1d4a0158db0d9efb67ca
> +
> +Datasheet is not publicly available.
> +
> +
> +Authors:
> + Maxim Sloyko <[email protected]>
> + Patrick Venture <[email protected]>
> +
> +Description
> +-----------
> +
> +IR38064 is a Single-input Voltage, Synchronous Buck Regulator, DC-DC Converter.
> +
> +Usage Notes
> +-----------
> +
> +This driver does not probe for PMBus devices. You will have to instantiate
> +devices explicitly.
> +
> +Sysfs attributes
> +----------------
> +
> +curr1_label "iout1"
> +curr1_input Measured output current
> +curr1_crit Critical maximum current
> +curr1_crit_alarm Current critical high alarm
> +curr1_max Maximum current
> +curr1_max_alarm Current high alarm
> +
> +in1_label "vin"
> +in1_input Measured input voltage
> +in1_crit Critical maximum input voltage
> +in1_crit_alarm Input voltage critical high alarm
> +in1_min Minimum input voltage
> +in1_min_alarm Input voltage low alarm
> +
> +in2_label "vout1"
> +in2_input Measured output voltage
> +in2_lcrit Critical minimum output voltage
> +in2_lcrit_alarm Output voltage critical low alarm
> +in2_crit Critical maximum output voltage
> +in2_crit_alarm Output voltage critical high alarm
> +in2_max Maximum output voltage
> +in2_max_alarm Output voltage high alarm
> +in2_min Minimum output voltage
> +in2_min_alarm Output voltage low alarm
> +
> +power1_label "pout1"
> +power1_input Measured output power
> +
> +temp1_input Measured temperature
> +temp1_crit Critical high temperature
> +temp1_crit_alarm Chip temperature critical high alarm
> +temp1_max Maximum temperature
> +temp1_max_alarm Chip temperature high alarm
> diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig
> index 629cb45f8557a..de87abab990e5 100644
> --- a/drivers/hwmon/pmbus/Kconfig
> +++ b/drivers/hwmon/pmbus/Kconfig
> @@ -54,6 +54,15 @@ config SENSORS_IR35221
> This driver can also be built as a module. If so, the module will
> be called ir35521.
>
> +config SENSORS_IR38064
> + tristate "Infineon IR38064"
> + help
> + If you say yes here you get hardware monitoring support for Infineon
> + IR38064.
> +
> + This driver can also be built as a module. If so, the module will
> + be called ir38064.
> +
> config SENSORS_LM25066
> tristate "National Semiconductor LM25066 and compatibles"
> help
> diff --git a/drivers/hwmon/pmbus/Makefile b/drivers/hwmon/pmbus/Makefile
> index ea0e39518c216..7d1fa6b3c8c93 100644
> --- a/drivers/hwmon/pmbus/Makefile
> +++ b/drivers/hwmon/pmbus/Makefile
> @@ -8,6 +8,7 @@ obj-$(CONFIG_SENSORS_PMBUS) += pmbus.o
> obj-$(CONFIG_SENSORS_ADM1275) += adm1275.o
> obj-$(CONFIG_SENSORS_IBM_CFFPS) += ibm-cffps.o
> obj-$(CONFIG_SENSORS_IR35221) += ir35221.o
> +obj-$(CONFIG_SENSORS_IR38064) += ir38064.o
> obj-$(CONFIG_SENSORS_LM25066) += lm25066.o
> obj-$(CONFIG_SENSORS_LTC2978) += ltc2978.o
> obj-$(CONFIG_SENSORS_LTC3815) += ltc3815.o
> diff --git a/drivers/hwmon/pmbus/ir38064.c b/drivers/hwmon/pmbus/ir38064.c
> new file mode 100644
> index 0000000000000..4b957ebb6fa71
> --- /dev/null
> +++ b/drivers/hwmon/pmbus/ir38064.c
> @@ -0,0 +1,60 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Hardware monitoring driver for Infineon IR38064
> + *
> + * Copyright (c) 2017 Google Inc
> + *
> + */
> +
> +#include <linux/err.h>
> +#include <linux/i2c.h>
> +#include <linux/init.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include "pmbus.h"
> +
> +static struct pmbus_driver_info ir38064_info = {
> + .pages = 1,
> + .format[PSC_VOLTAGE_IN] = linear,
> + .format[PSC_VOLTAGE_OUT] = direct,
The datasheet says this is linear16 format with exponent=-8.
Oddly enough, the datasheet also suggests that VOUT_MODE is
not supported, which would normally report the exponent.
I think it would be is better to implement a local read function
and fake VOUT_MODE instead of declaring direct mode, but then
I understand that it would make the code more complex. I'll
leave it up to you, but if you want to keep it as-is,
please explain in a comment that you are faking linear16
mode with exponent -8.
> + .format[PSC_CURRENT_OUT] = linear,
> + .format[PSC_POWER] = linear,
> + .format[PSC_TEMPERATURE] = linear,
> + .m[PSC_VOLTAGE_OUT] = 256,
> + .b[PSC_VOLTAGE_OUT] = 0,
> + .R[PSC_VOLTAGE_OUT] = 0,
> + .func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_STATUS_INPUT
> + | PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP
> + | PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT
> + | PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT
> + | PMBUS_HAVE_POUT,
> +};
> +
Not mandatory, but the chip does support VOUT_PEAK, IOUT_PEAK,
and TEMPERATURE_PEAK, just in case you are interested adding
support for it.
Thanks,
Guenter
> +static int ir38064_probe(struct i2c_client *client,
> + const struct i2c_device_id *id)
> +{
> + return pmbus_do_probe(client, id, &ir38064_info);
> +}
> +
> +static const struct i2c_device_id ir38064_id[] = {
> + {"ir38064", 0},
> + {}
> +};
> +
> +MODULE_DEVICE_TABLE(i2c, ir38064_id);
> +
> +/* This is the driver that will be inserted */
> +static struct i2c_driver ir38064_driver = {
> + .driver = {
> + .name = "ir38064",
> + },
> + .probe = ir38064_probe,
> + .remove = pmbus_do_remove,
> + .id_table = ir38064_id,
> +};
> +
> +module_i2c_driver(ir38064_driver);
> +
> +MODULE_AUTHOR("Maxim Sloyko <[email protected]>");
> +MODULE_DESCRIPTION("PMBus driver for Infineon IR38064");
> +MODULE_LICENSE("GPL");
>
On Fri, Apr 12, 2019 at 1:28 PM Guenter Roeck <[email protected]> wrote:
>
> On 4/12/19 12:43 PM, Patrick Venture wrote:
> > From: Maxim Sloyko <[email protected]>
> >
> > Add the pmbus driver for the Infineon ir38064 voltage regulator.
> >
> > Signed-off-by: Maxim Sloyko <[email protected]>
> > Signed-off-by: Patrick Venture <[email protected]>
> > ---
> > v2:
> > - Cleaned up weird tabbing behavior in doc.
> > v1:
> > - Initial patchset.
> > ---
> > Documentation/hwmon/ir38064 | 64 +++++++++++++++++++++++++++++++++++
> > drivers/hwmon/pmbus/Kconfig | 9 +++++
> > drivers/hwmon/pmbus/Makefile | 1 +
> > drivers/hwmon/pmbus/ir38064.c | 60 ++++++++++++++++++++++++++++++++
> > 4 files changed, 134 insertions(+)
> > create mode 100644 Documentation/hwmon/ir38064
> > create mode 100644 drivers/hwmon/pmbus/ir38064.c
> >
> > diff --git a/Documentation/hwmon/ir38064 b/Documentation/hwmon/ir38064
> > new file mode 100644
> > index 0000000000000..618779a329da0
> > --- /dev/null
> > +++ b/Documentation/hwmon/ir38064
> > @@ -0,0 +1,64 @@
> > +Kernel driver ir38064
> > +=====================
> > +
> > +Supported chips:
> > + * Infineon IR38064
> > + Prefix: 'ir38064'
> > + Addresses scanned: -
> > + Datasheet: Publicly available at the Infineon webiste
> > + https://www.infineon.com/dgdl/Infineon-IR38064MTRPBF-DS-v03_07-EN.pdf?fileId=5546d462584d1d4a0158db0d9efb67ca
> > +
> > +Datasheet is not publicly available.
> > +
> > +
> > +Authors:
> > + Maxim Sloyko <[email protected]>
> > + Patrick Venture <[email protected]>
> > +
> > +Description
> > +-----------
> > +
> > +IR38064 is a Single-input Voltage, Synchronous Buck Regulator, DC-DC Converter.
> > +
> > +Usage Notes
> > +-----------
> > +
> > +This driver does not probe for PMBus devices. You will have to instantiate
> > +devices explicitly.
> > +
> > +Sysfs attributes
> > +----------------
> > +
> > +curr1_label "iout1"
> > +curr1_input Measured output current
> > +curr1_crit Critical maximum current
> > +curr1_crit_alarm Current critical high alarm
> > +curr1_max Maximum current
> > +curr1_max_alarm Current high alarm
> > +
> > +in1_label "vin"
> > +in1_input Measured input voltage
> > +in1_crit Critical maximum input voltage
> > +in1_crit_alarm Input voltage critical high alarm
> > +in1_min Minimum input voltage
> > +in1_min_alarm Input voltage low alarm
> > +
> > +in2_label "vout1"
> > +in2_input Measured output voltage
> > +in2_lcrit Critical minimum output voltage
> > +in2_lcrit_alarm Output voltage critical low alarm
> > +in2_crit Critical maximum output voltage
> > +in2_crit_alarm Output voltage critical high alarm
> > +in2_max Maximum output voltage
> > +in2_max_alarm Output voltage high alarm
> > +in2_min Minimum output voltage
> > +in2_min_alarm Output voltage low alarm
> > +
> > +power1_label "pout1"
> > +power1_input Measured output power
> > +
> > +temp1_input Measured temperature
> > +temp1_crit Critical high temperature
> > +temp1_crit_alarm Chip temperature critical high alarm
> > +temp1_max Maximum temperature
> > +temp1_max_alarm Chip temperature high alarm
> > diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig
> > index 629cb45f8557a..de87abab990e5 100644
> > --- a/drivers/hwmon/pmbus/Kconfig
> > +++ b/drivers/hwmon/pmbus/Kconfig
> > @@ -54,6 +54,15 @@ config SENSORS_IR35221
> > This driver can also be built as a module. If so, the module will
> > be called ir35521.
> >
> > +config SENSORS_IR38064
> > + tristate "Infineon IR38064"
> > + help
> > + If you say yes here you get hardware monitoring support for Infineon
> > + IR38064.
> > +
> > + This driver can also be built as a module. If so, the module will
> > + be called ir38064.
> > +
> > config SENSORS_LM25066
> > tristate "National Semiconductor LM25066 and compatibles"
> > help
> > diff --git a/drivers/hwmon/pmbus/Makefile b/drivers/hwmon/pmbus/Makefile
> > index ea0e39518c216..7d1fa6b3c8c93 100644
> > --- a/drivers/hwmon/pmbus/Makefile
> > +++ b/drivers/hwmon/pmbus/Makefile
> > @@ -8,6 +8,7 @@ obj-$(CONFIG_SENSORS_PMBUS) += pmbus.o
> > obj-$(CONFIG_SENSORS_ADM1275) += adm1275.o
> > obj-$(CONFIG_SENSORS_IBM_CFFPS) += ibm-cffps.o
> > obj-$(CONFIG_SENSORS_IR35221) += ir35221.o
> > +obj-$(CONFIG_SENSORS_IR38064) += ir38064.o
> > obj-$(CONFIG_SENSORS_LM25066) += lm25066.o
> > obj-$(CONFIG_SENSORS_LTC2978) += ltc2978.o
> > obj-$(CONFIG_SENSORS_LTC3815) += ltc3815.o
> > diff --git a/drivers/hwmon/pmbus/ir38064.c b/drivers/hwmon/pmbus/ir38064.c
> > new file mode 100644
> > index 0000000000000..4b957ebb6fa71
> > --- /dev/null
> > +++ b/drivers/hwmon/pmbus/ir38064.c
> > @@ -0,0 +1,60 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +/*
> > + * Hardware monitoring driver for Infineon IR38064
> > + *
> > + * Copyright (c) 2017 Google Inc
> > + *
> > + */
> > +
> > +#include <linux/err.h>
> > +#include <linux/i2c.h>
> > +#include <linux/init.h>
> > +#include <linux/kernel.h>
> > +#include <linux/module.h>
> > +#include "pmbus.h"
> > +
> > +static struct pmbus_driver_info ir38064_info = {
> > + .pages = 1,
> > + .format[PSC_VOLTAGE_IN] = linear,
> > + .format[PSC_VOLTAGE_OUT] = direct,
>
> The datasheet says this is linear16 format with exponent=-8.
> Oddly enough, the datasheet also suggests that VOUT_MODE is
> not supported, which would normally report the exponent.
> I think it would be is better to implement a local read function
> and fake VOUT_MODE instead of declaring direct mode, but then
> I understand that it would make the code more complex. I'll
> leave it up to you, but if you want to keep it as-is,
> please explain in a comment that you are faking linear16
> mode with exponent -8.
Added to commit message in v3.
>
> > + .format[PSC_CURRENT_OUT] = linear,
> > + .format[PSC_POWER] = linear,
> > + .format[PSC_TEMPERATURE] = linear,
> > + .m[PSC_VOLTAGE_OUT] = 256,
> > + .b[PSC_VOLTAGE_OUT] = 0,
> > + .R[PSC_VOLTAGE_OUT] = 0,
> > + .func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_STATUS_INPUT
> > + | PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP
> > + | PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT
> > + | PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT
> > + | PMBUS_HAVE_POUT,
> > +};
> > +
>
> Not mandatory, but the chip does support VOUT_PEAK, IOUT_PEAK,
> and TEMPERATURE_PEAK, just in case you are interested adding
> support for it.
Added to commit message in v3.
>
> Thanks,
> Guenter
Thanks.
>
> > +static int ir38064_probe(struct i2c_client *client,
> > + const struct i2c_device_id *id)
> > +{
> > + return pmbus_do_probe(client, id, &ir38064_info);
> > +}
> > +
> > +static const struct i2c_device_id ir38064_id[] = {
> > + {"ir38064", 0},
> > + {}
> > +};
> > +
> > +MODULE_DEVICE_TABLE(i2c, ir38064_id);
> > +
> > +/* This is the driver that will be inserted */
> > +static struct i2c_driver ir38064_driver = {
> > + .driver = {
> > + .name = "ir38064",
> > + },
> > + .probe = ir38064_probe,
> > + .remove = pmbus_do_remove,
> > + .id_table = ir38064_id,
> > +};
> > +
> > +module_i2c_driver(ir38064_driver);
> > +
> > +MODULE_AUTHOR("Maxim Sloyko <[email protected]>");
> > +MODULE_DESCRIPTION("PMBus driver for Infineon IR38064");
> > +MODULE_LICENSE("GPL");
> >
>