So, I apologize in advance for this relatively vague report, but I'm fairly sure
the Yoga 900 has an accelerometer amongst other sensors (ambient light?)
exported over IIO.
But, these sensors seem to not be updating at all with a 4.4-rc5+ kernel (a
set of patches from https://lkml.org/lkml/2015/11/30/441 applied to Linus'
tree).
The odd part is at some point in messing with this, I'm fairly sure it did work!
That is,
`watch -n 0.1 cat '/sys/bus/iio/devices/iio:device'*/*raw*`
showed updating values as I moved the laptop around.
I've not done any accelerometer debugging before, so any suggestion on
where to start would be greatly appreciated!
-Nish
Hi,
So you were using 4.4-rc5 before and it worked, but after applying a
patch it stopped?
The patch you pasted seems to relate to dts files and declarations in
it - did anything there change?
Best regards,
Crt
On 15 December 2015 at 20:19, Nish Aravamudan <[email protected]> wrote:
> So, I apologize in advance for this relatively vague report, but I'm fairly sure
> the Yoga 900 has an accelerometer amongst other sensors (ambient light?)
> exported over IIO.
>
> But, these sensors seem to not be updating at all with a 4.4-rc5+ kernel (a
> set of patches from https://lkml.org/lkml/2015/11/30/441 applied to Linus'
> tree).
>
> The odd part is at some point in messing with this, I'm fairly sure it did work!
> That is,
>
> `watch -n 0.1 cat '/sys/bus/iio/devices/iio:device'*/*raw*`
>
> showed updating values as I moved the laptop around.
>
> I've not done any accelerometer debugging before, so any suggestion on
> where to start would be greatly appreciated!
>
> -Nish
> --
> To unsubscribe from this list: send the line "unsubscribe linux-iio" in
> the body of a message to [email protected]
> More majordomo info at http://vger.kernel.org/majordomo-info.html
On Tue, Dec 15, 2015 at 9:19 PM, Nish Aravamudan
<[email protected]> wrote:
> So, I apologize in advance for this relatively vague report, but I'm fairly sure
> the Yoga 900 has an accelerometer amongst other sensors (ambient light?)
> exported over IIO.
>
> But, these sensors seem to not be updating at all with a 4.4-rc5+ kernel (a
> set of patches from https://lkml.org/lkml/2015/11/30/441 applied to Linus'
> tree).
>
> The odd part is at some point in messing with this, I'm fairly sure it did work!
> That is,
>
> `watch -n 0.1 cat '/sys/bus/iio/devices/iio:device'*/*raw*`
Can you send us a sample of the output? Also, would be
good to identify the exact driver for accel.
Perhaps: cat /sys/bus/iio/devices/iio:device'*/name
>
> showed updating values as I moved the laptop around.
>
> I've not done any accelerometer debugging before, so any suggestion on
> where to start would be greatly appreciated!
Did you applied some patches and recompiled the kernel? Or when it did stopped
working?
thanks,
Daniel.
On Wed, Dec 16, 2015 at 1:31 AM, Crt Mori <[email protected]> wrote:
> Hi,
> So you were using 4.4-rc5 before and it worked, but after applying a
> patch it stopped?
Sorry, I should have explained it better. Without the patchset
referred to in my original e-mail, the touchpad simply doesn't work.
However, I do have an external mouse, so let me go back to stock
4.4-rc5 and test the IIO inputs.
Thanks,
Nish
Hi Daniel,
On Wed, Dec 16, 2015 at 1:43 AM, Daniel Baluta <[email protected]> wrote:
> On Tue, Dec 15, 2015 at 9:19 PM, Nish Aravamudan
> <[email protected]> wrote:
>> So, I apologize in advance for this relatively vague report, but I'm fairly sure
>> the Yoga 900 has an accelerometer amongst other sensors (ambient light?)
>> exported over IIO.
>>
>> But, these sensors seem to not be updating at all with a 4.4-rc5+ kernel (a
>> set of patches from https://lkml.org/lkml/2015/11/30/441 applied to Linus'
>> tree).
>>
>> The odd part is at some point in messing with this, I'm fairly sure it did work!
>> That is,
>>
>> `watch -n 0.1 cat '/sys/bus/iio/devices/iio:device'*/*raw*`
>
> Can you send us a sample of the output? Also, would be
> good to identify the exact driver for accel.
cat /sys/bus/iio/devices/iio:device*/*raw*
65478
7
1023
0
0
0
100
-539062
-742187
1292968
1592
64932
2
275
0 0 0 0
Now, I should say that I distinctly remember at some point waving my
laptop around and seeing these values change ... but now they seem to
be "stuck". Maybe it's a hardware issue or something special that
WIndows does to leverage the IIO sensors?
> Perhaps: cat /sys/bus/iio/devices/iio:device'*/name
$ cat /sys/bus/iio/devices/iio:device*/name
accel_3d
gyro_3d
als
magn_3d
incli_3d
dev_rotation
>>
>> showed updating values as I moved the laptop around.
>>
>> I've not done any accelerometer debugging before, so any suggestion on
>> where to start would be greatly appreciated!
>
> Did you applied some patches and recompiled the kernel? Or when it did stopped
> working?
As far as I can tell, it only worked that one one time and hasn't
since. Although your question does make me wonder *which* kernel I was
on that I experienced the values changing. Let me go back to a stock
4.4-rc5 and see.
-Nish
On 16 December 2015 at 22:41, Nish Aravamudan <[email protected]> wrote:
> Hi Daniel,
>
> On Wed, Dec 16, 2015 at 1:43 AM, Daniel Baluta <[email protected]> wrote:
>> On Tue, Dec 15, 2015 at 9:19 PM, Nish Aravamudan
>> <[email protected]> wrote:
>>> So, I apologize in advance for this relatively vague report, but I'm fairly sure
>>> the Yoga 900 has an accelerometer amongst other sensors (ambient light?)
>>> exported over IIO.
>>>
>>> But, these sensors seem to not be updating at all with a 4.4-rc5+ kernel (a
>>> set of patches from https://lkml.org/lkml/2015/11/30/441 applied to Linus'
>>> tree).
>>>
>>> The odd part is at some point in messing with this, I'm fairly sure it did work!
>>> That is,
>>>
>>> `watch -n 0.1 cat '/sys/bus/iio/devices/iio:device'*/*raw*`
>>
>> Can you send us a sample of the output? Also, would be
>> good to identify the exact driver for accel.
>
> cat /sys/bus/iio/devices/iio:device*/*raw*
> 65478
> 7
> 1023
> 0
> 0
> 0
> 100
> -539062
> -742187
> 1292968
> 1592
> 64932
> 2
> 275
> 0 0 0 0
>
> Now, I should say that I distinctly remember at some point waving my
> laptop around and seeing these values change ... but now they seem to
> be "stuck". Maybe it's a hardware issue or something special that
> WIndows does to leverage the IIO sensors?
>
>> Perhaps: cat /sys/bus/iio/devices/iio:device'*/name
>
> $ cat /sys/bus/iio/devices/iio:device*/name
> accel_3d
Can you list the directory of iio:device with this name (it is:
drivers/iio/accel/hid-sensor-accel-3d.c).
This is something you will be looking at for accel debugging, but it
seems more like
standard
> gyro_3d
> als
> magn_3d
> incli_3d
> dev_rotation
>
>
>>>
>>> showed updating values as I moved the laptop around.
>>>
>>> I've not done any accelerometer debugging before, so any suggestion on
>>> where to start would be greatly appreciated!
>>
>> Did you applied some patches and recompiled the kernel? Or when it did stopped
>> working?
>
> As far as I can tell, it only worked that one one time and hasn't
> since. Although your question does make me wonder *which* kernel I was
> on that I experienced the values changing. Let me go back to a stock
> 4.4-rc5 and see.
Did you compile the stock kernel? It might be that .dts file you are
using (or defconfig)
is not correct.
Hi,
On Wed, Dec 16, 2015 at 2:22 PM, Crt Mori <[email protected]> wrote:
> On 16 December 2015 at 22:41, Nish Aravamudan <[email protected]> wrote:
>> Hi Daniel,
>>
>> On Wed, Dec 16, 2015 at 1:43 AM, Daniel Baluta <[email protected]> wrote:
>>> On Tue, Dec 15, 2015 at 9:19 PM, Nish Aravamudan
>>> <[email protected]> wrote:
>>>> So, I apologize in advance for this relatively vague report, but I'm fairly sure
>>>> the Yoga 900 has an accelerometer amongst other sensors (ambient light?)
>>>> exported over IIO.
>>>>
>>>> But, these sensors seem to not be updating at all with a 4.4-rc5+ kernel (a
>>>> set of patches from https://lkml.org/lkml/2015/11/30/441 applied to Linus'
>>>> tree).
>>>>
>>>> The odd part is at some point in messing with this, I'm fairly sure it did work!
>>>> That is,
>>>>
>>>> `watch -n 0.1 cat '/sys/bus/iio/devices/iio:device'*/*raw*`
>>>
>>> Can you send us a sample of the output? Also, would be
>>> good to identify the exact driver for accel.
>>
>> cat /sys/bus/iio/devices/iio:device*/*raw*
>> 65478
>> 7
>> 1023
>> 0
>> 0
>> 0
>> 100
>> -539062
>> -742187
>> 1292968
>> 1592
>> 64932
>> 2
>> 275
>> 0 0 0 0
>>
>> Now, I should say that I distinctly remember at some point waving my
>> laptop around and seeing these values change ... but now they seem to
>> be "stuck". Maybe it's a hardware issue or something special that
>> WIndows does to leverage the IIO sensors?
>>
>>> Perhaps: cat /sys/bus/iio/devices/iio:device'*/name
>>
>> $ cat /sys/bus/iio/devices/iio:device*/name
>> accel_3d
>
> Can you list the directory of iio:device with this name (it is:
> drivers/iio/accel/hid-sensor-accel-3d.c).
> This is something you will be looking at for accel debugging, but it
> seems more like
> standard
/sys/bus/iio/devices/iio:device0/name
gyro_3d
/sys/bus/iio/devices/iio:device1/name
dev_rotation
/sys/bus/iio/devices/iio:device2/name
als
/sys/bus/iio/devices/iio:device3/name
magn_3d
/sys/bus/iio/devices/iio:device4/name
accel_3d
/sys/bus/iio/devices/iio:device5/name
incli_3d
are all the IIO sensors, sorry about that!
>> gyro_3d
>> als
>> magn_3d
>> incli_3d
>> dev_rotation
>>
>>
>>>>
>>>> showed updating values as I moved the laptop around.
>>>>
>>>> I've not done any accelerometer debugging before, so any suggestion on
>>>> where to start would be greatly appreciated!
>>>
>>> Did you applied some patches and recompiled the kernel? Or when it did stopped
>>> working?
>>
>> As far as I can tell, it only worked that one one time and hasn't
>> since. Although your question does make me wonder *which* kernel I was
>> on that I experienced the values changing. Let me go back to a stock
>> 4.4-rc5 and see.
>
> Did you compile the stock kernel? It might be that .dts file you are
> using (or defconfig)
> is not correct.
I compiled the stock kernel, based off the the Ubuntu 15.04 .config,
trimmed to account for the hardware I have on the system. I can attach
the .config if that will be useful.
I just went back to 4.4-rc4 and it also didn't seem to have any
updates to the raw file contents.
-Nish
On Wed, Dec 16, 2015 at 2:55 PM, Crt Mori <[email protected]> wrote:
>
> On Dec 16, 2015 11:37 PM, "Nish Aravamudan" <[email protected]>
> wrote:
>>
>> Hi,
>>
>> On Wed, Dec 16, 2015 at 2:22 PM, Crt Mori <[email protected]> wrote:
>> > On 16 December 2015 at 22:41, Nish Aravamudan
>> > <[email protected]> wrote:
>> >> Hi Daniel,
>> >>
>> >> On Wed, Dec 16, 2015 at 1:43 AM, Daniel Baluta
>> >> <[email protected]> wrote:
>> >>> On Tue, Dec 15, 2015 at 9:19 PM, Nish Aravamudan
>> >>> <[email protected]> wrote:
>> >>>> So, I apologize in advance for this relatively vague report, but I'm
>> >>>> fairly sure
>> >>>> the Yoga 900 has an accelerometer amongst other sensors (ambient
>> >>>> light?)
>> >>>> exported over IIO.
>> >>>>
>> >>>> But, these sensors seem to not be updating at all with a 4.4-rc5+
>> >>>> kernel (a
>> >>>> set of patches from https://lkml.org/lkml/2015/11/30/441 applied to
>> >>>> Linus'
>> >>>> tree).
>> >>>>
>> >>>> The odd part is at some point in messing with this, I'm fairly sure
>> >>>> it did work!
>> >>>> That is,
>> >>>>
>> >>>> `watch -n 0.1 cat '/sys/bus/iio/devices/iio:device'*/*raw*`
>> >>>
>> >>> Can you send us a sample of the output? Also, would be
>> >>> good to identify the exact driver for accel.
>> >>
>> >> cat /sys/bus/iio/devices/iio:device*/*raw*
>> >> 65478
>> >> 7
>> >> 1023
>> >> 0
>> >> 0
>> >> 0
>> >> 100
>> >> -539062
>> >> -742187
>> >> 1292968
>> >> 1592
>> >> 64932
>> >> 2
>> >> 275
>> >> 0 0 0 0
>> >>
>> >> Now, I should say that I distinctly remember at some point waving my
>> >> laptop around and seeing these values change ... but now they seem to
>> >> be "stuck". Maybe it's a hardware issue or something special that
>> >> WIndows does to leverage the IIO sensors?
>> >>
>> >>> Perhaps: cat /sys/bus/iio/devices/iio:device'*/name
>> >>
>> >> $ cat /sys/bus/iio/devices/iio:device*/name
>> >> accel_3d
>> >
>> > Can you list the directory of iio:device with this name (it is:
>> > drivers/iio/accel/hid-sensor-accel-3d.c).
>> > This is something you will be looking at for accel debugging, but it
>> > seems more like
>> > standard
>>
>> /sys/bus/iio/devices/iio:device0/name
>> gyro_3d
>> /sys/bus/iio/devices/iio:device1/name
>> dev_rotation
>> /sys/bus/iio/devices/iio:device2/name
>> als
>> /sys/bus/iio/devices/iio:device3/name
>> magn_3d
>> /sys/bus/iio/devices/iio:device4/name
>> accel_3d
>> /sys/bus/iio/devices/iio:device5/name
>> incli_3d
>>
>> are all the IIO sensors, sorry about that!
>>
>
> I was more thinking what else is in iio:device4 directory, so that we can
> see if it was initialized OK. Can you also grep the dmesg for any errors?
Well, I just noticed the device #s are not consistent boot-to-boot, so
this time it was device0. Trimming out the directories:
/sys/bus/iio/devices/iio:device0/buffer
cat: /sys/bus/iio/devices/iio:device0/buffer: Is a directory
/sys/bus/iio/devices/iio:device0/dev
250:0
/sys/bus/iio/devices/iio:device0/in_accel_hysteresis
cat: /sys/bus/iio/devices/iio:device0/in_accel_hysteresis: Invalid argument
/sys/bus/iio/devices/iio:device0/in_accel_offset
0
/sys/bus/iio/devices/iio:device0/in_accel_sampling_frequency
8.000000
/sys/bus/iio/devices/iio:device0/in_accel_scale
0.009806
/sys/bus/iio/devices/iio:device0/in_accel_x_raw
65478
/sys/bus/iio/devices/iio:device0/in_accel_y_raw
7
/sys/bus/iio/devices/iio:device0/in_accel_z_raw
1023
/sys/bus/iio/devices/iio:device0/name
accel_3d
/sys/bus/iio/devices/iio:device0/uevent
MAJOR=250
MINOR=0
DEVNAME=iio:device0
DEVTYPE=iio_device
Another thing I just noticed:
/sys/bus/iio/devices/iio:device0/buffer/enable
0
The only error I'm getting consistently is:
[ 1.115327] i2c_hid i2c-ITE8396:00: error in i2c_hid_init_report
size:19 / ret_size:18
which I don't think is relevant, but I might be wrong.
>> >> gyro_3d
>> >> als
>> >> magn_3d
>> >> incli_3d
>> >> dev_rotation
>> >>
>> >>
>> >>>>
>> >>>> showed updating values as I moved the laptop around.
>> >>>>
>> >>>> I've not done any accelerometer debugging before, so any suggestion
>> >>>> on
>> >>>> where to start would be greatly appreciated!
>> >>>
>> >>> Did you applied some patches and recompiled the kernel? Or when it did
>> >>> stopped
>> >>> working?
>> >>
>> >> As far as I can tell, it only worked that one one time and hasn't
>> >> since. Although your question does make me wonder *which* kernel I was
>> >> on that I experienced the values changing. Let me go back to a stock
>> >> 4.4-rc5 and see.
>> >
>> > Did you compile the stock kernel? It might be that .dts file you are
>> > using (or defconfig)
>> > is not correct.
>>
>> I compiled the stock kernel, based off the the Ubuntu 15.04 .config,
>> trimmed to account for the hardware I have on the system. I can attach
>> the .config if that will be useful.
>>
>> I just went back to 4.4-rc4 and it also didn't seem to have any
>> updates to the raw file contents.
>>
>
> I hope full post of your defconfig will not be needed. However could you
> double check that you have enabled all drivers for accel (check the kbuild
> file in drivers/iio/accel). If they have driver for accel in main kernel (or
> staging) then it will link with existing device tree nicely.
I'll go back and enable everything just to be safe. Building now, will
report the results once I have them.
-Nish
On Wed, Dec 16, 2015 at 3:05 PM, Nish Aravamudan
<[email protected]> wrote:
> On Wed, Dec 16, 2015 at 2:55 PM, Crt Mori <[email protected]> wrote:
>>
>> On Dec 16, 2015 11:37 PM, "Nish Aravamudan" <[email protected]>
>> wrote:
>>>
>>> Hi,
>>>
>>> On Wed, Dec 16, 2015 at 2:22 PM, Crt Mori <[email protected]> wrote:
>>> > On 16 December 2015 at 22:41, Nish Aravamudan
>>> > <[email protected]> wrote:
>>> >> Hi Daniel,
>>> >>
>>> >> On Wed, Dec 16, 2015 at 1:43 AM, Daniel Baluta
>>> >> <[email protected]> wrote:
>>> >>> On Tue, Dec 15, 2015 at 9:19 PM, Nish Aravamudan
>>> >>> <[email protected]> wrote:
>>> >>>> So, I apologize in advance for this relatively vague report, but I'm
>>> >>>> fairly sure
>>> >>>> the Yoga 900 has an accelerometer amongst other sensors (ambient
>>> >>>> light?)
>>> >>>> exported over IIO.
>>> >>>>
>>> >>>> But, these sensors seem to not be updating at all with a 4.4-rc5+
>>> >>>> kernel (a
>>> >>>> set of patches from https://lkml.org/lkml/2015/11/30/441 applied to
>>> >>>> Linus'
>>> >>>> tree).
>>> >>>>
>>> >>>> The odd part is at some point in messing with this, I'm fairly sure
>>> >>>> it did work!
>>> >>>> That is,
>>> >>>>
>>> >>>> `watch -n 0.1 cat '/sys/bus/iio/devices/iio:device'*/*raw*`
>>> >>>
>>> >>> Can you send us a sample of the output? Also, would be
>>> >>> good to identify the exact driver for accel.
>>> >>
>>> >> cat /sys/bus/iio/devices/iio:device*/*raw*
>>> >> 65478
>>> >> 7
>>> >> 1023
>>> >> 0
>>> >> 0
>>> >> 0
>>> >> 100
>>> >> -539062
>>> >> -742187
>>> >> 1292968
>>> >> 1592
>>> >> 64932
>>> >> 2
>>> >> 275
>>> >> 0 0 0 0
>>> >>
>>> >> Now, I should say that I distinctly remember at some point waving my
>>> >> laptop around and seeing these values change ... but now they seem to
>>> >> be "stuck". Maybe it's a hardware issue or something special that
>>> >> WIndows does to leverage the IIO sensors?
>>> >>
>>> >>> Perhaps: cat /sys/bus/iio/devices/iio:device'*/name
>>> >>
>>> >> $ cat /sys/bus/iio/devices/iio:device*/name
>>> >> accel_3d
>>> >
>>> > Can you list the directory of iio:device with this name (it is:
>>> > drivers/iio/accel/hid-sensor-accel-3d.c).
>>> > This is something you will be looking at for accel debugging, but it
>>> > seems more like
>>> > standard
>>>
>>> /sys/bus/iio/devices/iio:device0/name
>>> gyro_3d
>>> /sys/bus/iio/devices/iio:device1/name
>>> dev_rotation
>>> /sys/bus/iio/devices/iio:device2/name
>>> als
>>> /sys/bus/iio/devices/iio:device3/name
>>> magn_3d
>>> /sys/bus/iio/devices/iio:device4/name
>>> accel_3d
>>> /sys/bus/iio/devices/iio:device5/name
>>> incli_3d
>>>
>>> are all the IIO sensors, sorry about that!
>>>
>>
>> I was more thinking what else is in iio:device4 directory, so that we can
>> see if it was initialized OK. Can you also grep the dmesg for any errors?
>
> Well, I just noticed the device #s are not consistent boot-to-boot, so
> this time it was device0. Trimming out the directories:
>
> /sys/bus/iio/devices/iio:device0/buffer
> cat: /sys/bus/iio/devices/iio:device0/buffer: Is a directory
> /sys/bus/iio/devices/iio:device0/dev
> 250:0
> /sys/bus/iio/devices/iio:device0/in_accel_hysteresis
> cat: /sys/bus/iio/devices/iio:device0/in_accel_hysteresis: Invalid argument
> /sys/bus/iio/devices/iio:device0/in_accel_offset
> 0
> /sys/bus/iio/devices/iio:device0/in_accel_sampling_frequency
> 8.000000
> /sys/bus/iio/devices/iio:device0/in_accel_scale
> 0.009806
> /sys/bus/iio/devices/iio:device0/in_accel_x_raw
> 65478
> /sys/bus/iio/devices/iio:device0/in_accel_y_raw
> 7
> /sys/bus/iio/devices/iio:device0/in_accel_z_raw
> 1023
> /sys/bus/iio/devices/iio:device0/name
> accel_3d
> /sys/bus/iio/devices/iio:device0/uevent
> MAJOR=250
> MINOR=0
> DEVNAME=iio:device0
> DEVTYPE=iio_device
>
> Another thing I just noticed:
>
> /sys/bus/iio/devices/iio:device0/buffer/enable
> 0
>
> The only error I'm getting consistently is:
>
> [ 1.115327] i2c_hid i2c-ITE8396:00: error in i2c_hid_init_report
> size:19 / ret_size:18
>
> which I don't think is relevant, but I might be wrong.
>
>>> >> gyro_3d
>>> >> als
>>> >> magn_3d
>>> >> incli_3d
>>> >> dev_rotation
>>> >>
>>> >>
>>> >>>>
>>> >>>> showed updating values as I moved the laptop around.
>>> >>>>
>>> >>>> I've not done any accelerometer debugging before, so any suggestion
>>> >>>> on
>>> >>>> where to start would be greatly appreciated!
>>> >>>
>>> >>> Did you applied some patches and recompiled the kernel? Or when it did
>>> >>> stopped
>>> >>> working?
>>> >>
>>> >> As far as I can tell, it only worked that one one time and hasn't
>>> >> since. Although your question does make me wonder *which* kernel I was
>>> >> on that I experienced the values changing. Let me go back to a stock
>>> >> 4.4-rc5 and see.
>>> >
>>> > Did you compile the stock kernel? It might be that .dts file you are
>>> > using (or defconfig)
>>> > is not correct.
>>>
>>> I compiled the stock kernel, based off the the Ubuntu 15.04 .config,
>>> trimmed to account for the hardware I have on the system. I can attach
>>> the .config if that will be useful.
>>>
>>> I just went back to 4.4-rc4 and it also didn't seem to have any
>>> updates to the raw file contents.
>>>
>>
>> I hope full post of your defconfig will not be needed. However could you
>> double check that you have enabled all drivers for accel (check the kbuild
>> file in drivers/iio/accel). If they have driver for accel in main kernel (or
>> staging) then it will link with existing device tree nicely.
>
> I'll go back and enable everything just to be safe. Building now, will
> report the results once I have them.
Using the stock Ubuntu .config as the base, meaning many, many modules
(including all possible IIO accelerometers, it seems), I still see no
updates to the *raw* file contents.
-Nish
On 17 December 2015 at 06:27, Nish Aravamudan <[email protected]> wrote:
> On Wed, Dec 16, 2015 at 3:05 PM, Nish Aravamudan
> <[email protected]> wrote:
>> On Wed, Dec 16, 2015 at 2:55 PM, Crt Mori <[email protected]> wrote:
>>>
>>> On Dec 16, 2015 11:37 PM, "Nish Aravamudan" <[email protected]>
>>> wrote:
>>>>
>>>> Hi,
>>>>
>>>> On Wed, Dec 16, 2015 at 2:22 PM, Crt Mori <[email protected]> wrote:
>>>> > On 16 December 2015 at 22:41, Nish Aravamudan
>>>> > <[email protected]> wrote:
>>>> >> Hi Daniel,
>>>> >>
>>>> >> On Wed, Dec 16, 2015 at 1:43 AM, Daniel Baluta
>>>> >> <[email protected]> wrote:
>>>> >>> On Tue, Dec 15, 2015 at 9:19 PM, Nish Aravamudan
>>>> >>> <[email protected]> wrote:
>>>> >>>> So, I apologize in advance for this relatively vague report, but I'm
>>>> >>>> fairly sure
>>>> >>>> the Yoga 900 has an accelerometer amongst other sensors (ambient
>>>> >>>> light?)
>>>> >>>> exported over IIO.
>>>> >>>>
>>>> >>>> But, these sensors seem to not be updating at all with a 4.4-rc5+
>>>> >>>> kernel (a
>>>> >>>> set of patches from https://lkml.org/lkml/2015/11/30/441 applied to
>>>> >>>> Linus'
>>>> >>>> tree).
>>>> >>>>
>>>> >>>> The odd part is at some point in messing with this, I'm fairly sure
>>>> >>>> it did work!
>>>> >>>> That is,
>>>> >>>>
>>>> >>>> `watch -n 0.1 cat '/sys/bus/iio/devices/iio:device'*/*raw*`
>>>> >>>
>>>> >>> Can you send us a sample of the output? Also, would be
>>>> >>> good to identify the exact driver for accel.
>>>> >>
>>>> >> cat /sys/bus/iio/devices/iio:device*/*raw*
>>>> >> 65478
>>>> >> 7
>>>> >> 1023
>>>> >> 0
>>>> >> 0
>>>> >> 0
>>>> >> 100
>>>> >> -539062
>>>> >> -742187
>>>> >> 1292968
>>>> >> 1592
>>>> >> 64932
>>>> >> 2
>>>> >> 275
>>>> >> 0 0 0 0
>>>> >>
>>>> >> Now, I should say that I distinctly remember at some point waving my
>>>> >> laptop around and seeing these values change ... but now they seem to
>>>> >> be "stuck". Maybe it's a hardware issue or something special that
>>>> >> WIndows does to leverage the IIO sensors?
>>>> >>
>>>> >>> Perhaps: cat /sys/bus/iio/devices/iio:device'*/name
>>>> >>
>>>> >> $ cat /sys/bus/iio/devices/iio:device*/name
>>>> >> accel_3d
>>>> >
>>>> > Can you list the directory of iio:device with this name (it is:
>>>> > drivers/iio/accel/hid-sensor-accel-3d.c).
>>>> > This is something you will be looking at for accel debugging, but it
>>>> > seems more like
>>>> > standard
>>>>
>>>> /sys/bus/iio/devices/iio:device0/name
>>>> gyro_3d
>>>> /sys/bus/iio/devices/iio:device1/name
>>>> dev_rotation
>>>> /sys/bus/iio/devices/iio:device2/name
>>>> als
>>>> /sys/bus/iio/devices/iio:device3/name
>>>> magn_3d
>>>> /sys/bus/iio/devices/iio:device4/name
>>>> accel_3d
>>>> /sys/bus/iio/devices/iio:device5/name
>>>> incli_3d
>>>>
>>>> are all the IIO sensors, sorry about that!
>>>>
>>>
>>> I was more thinking what else is in iio:device4 directory, so that we can
>>> see if it was initialized OK. Can you also grep the dmesg for any errors?
>>
>> Well, I just noticed the device #s are not consistent boot-to-boot, so
>> this time it was device0. Trimming out the directories:
>>
This is correct/intended. You need to confirm "deviceX/name" each time.
>> /sys/bus/iio/devices/iio:device0/buffer
>> cat: /sys/bus/iio/devices/iio:device0/buffer: Is a directory
>> /sys/bus/iio/devices/iio:device0/dev
>> 250:0
>> /sys/bus/iio/devices/iio:device0/in_accel_hysteresis
>> cat: /sys/bus/iio/devices/iio:device0/in_accel_hysteresis: Invalid argument
>> /sys/bus/iio/devices/iio:device0/in_accel_offset
>> 0
>> /sys/bus/iio/devices/iio:device0/in_accel_sampling_frequency
>> 8.000000
>> /sys/bus/iio/devices/iio:device0/in_accel_scale
>> 0.009806
>> /sys/bus/iio/devices/iio:device0/in_accel_x_raw
>> 65478
>> /sys/bus/iio/devices/iio:device0/in_accel_y_raw
>> 7
>> /sys/bus/iio/devices/iio:device0/in_accel_z_raw
>> 1023
This seems like a valid number 1023 * 0.009806 = 10,031 m/s2 but X does not.
>> /sys/bus/iio/devices/iio:device0/name
>> accel_3d
>> /sys/bus/iio/devices/iio:device0/uevent
>> MAJOR=250
>> MINOR=0
>> DEVNAME=iio:device0
>> DEVTYPE=iio_device
>>
>> Another thing I just noticed:
>>
>> /sys/bus/iio/devices/iio:device0/buffer/enable
>> 0
This is buffer enable not chip enable. You can write 1 to that so it
will be enables
(echo "1" > /sys/bus/iio/devices/.../buffer/enable) and see what
happens. It might be
that it needs buffer to update properly (I haven't checked the code).
>>
>> The only error I'm getting consistently is:
>>
>> [ 1.115327] i2c_hid i2c-ITE8396:00: error in i2c_hid_init_report
>> size:19 / ret_size:18
>>
>> which I don't think is relevant, but I might be wrong.
If accel is i2c this might be a relevant error - and probe would also
not fail, but error would
repeat itself each time probably Maybe track where that line is in
i2c_hid and see what it
could mean.
>>
>>>> >> gyro_3d
>>>> >> als
>>>> >> magn_3d
>>>> >> incli_3d
>>>> >> dev_rotation
>>>> >>
>>>> >>
>>>> >>>>
>>>> >>>> showed updating values as I moved the laptop around.
>>>> >>>>
>>>> >>>> I've not done any accelerometer debugging before, so any suggestion
>>>> >>>> on
>>>> >>>> where to start would be greatly appreciated!
>>>> >>>
>>>> >>> Did you applied some patches and recompiled the kernel? Or when it did
>>>> >>> stopped
>>>> >>> working?
>>>> >>
>>>> >> As far as I can tell, it only worked that one one time and hasn't
>>>> >> since. Although your question does make me wonder *which* kernel I was
>>>> >> on that I experienced the values changing. Let me go back to a stock
>>>> >> 4.4-rc5 and see.
>>>> >
>>>> > Did you compile the stock kernel? It might be that .dts file you are
>>>> > using (or defconfig)
>>>> > is not correct.
>>>>
>>>> I compiled the stock kernel, based off the the Ubuntu 15.04 .config,
>>>> trimmed to account for the hardware I have on the system. I can attach
>>>> the .config if that will be useful.
>>>>
>>>> I just went back to 4.4-rc4 and it also didn't seem to have any
>>>> updates to the raw file contents.
>>>>
>>>
>>> I hope full post of your defconfig will not be needed. However could you
>>> double check that you have enabled all drivers for accel (check the kbuild
>>> file in drivers/iio/accel). If they have driver for accel in main kernel (or
>>> staging) then it will link with existing device tree nicely.
>>
>> I'll go back and enable everything just to be safe. Building now, will
>> report the results once I have them.
>
> Using the stock Ubuntu .config as the base, meaning many, many modules
> (including all possible IIO accelerometers, it seems), I still see no
> updates to the *raw* file contents.
>
> -Nish
On Thu, Dec 17, 2015 at 12:41 AM, Crt Mori <[email protected]> wrote:
> On 17 December 2015 at 06:27, Nish Aravamudan <[email protected]> wrote:
>> On Wed, Dec 16, 2015 at 3:05 PM, Nish Aravamudan
>> <[email protected]> wrote:
>>> On Wed, Dec 16, 2015 at 2:55 PM, Crt Mori <[email protected]> wrote:
>>>>
>>>> On Dec 16, 2015 11:37 PM, "Nish Aravamudan" <[email protected]>
>>>> wrote:
>>>>>
>>>>> Hi,
>>>>>
>>>>> On Wed, Dec 16, 2015 at 2:22 PM, Crt Mori <[email protected]> wrote:
>>>>> > On 16 December 2015 at 22:41, Nish Aravamudan
>>>>> > <[email protected]> wrote:
>>>>> >> Hi Daniel,
>>>>> >>
>>>>> >> On Wed, Dec 16, 2015 at 1:43 AM, Daniel Baluta
>>>>> >> <[email protected]> wrote:
>>>>> >>> On Tue, Dec 15, 2015 at 9:19 PM, Nish Aravamudan
>>>>> >>> <[email protected]> wrote:
>>>>> >>>> So, I apologize in advance for this relatively vague report, but I'm
>>>>> >>>> fairly sure
>>>>> >>>> the Yoga 900 has an accelerometer amongst other sensors (ambient
>>>>> >>>> light?)
>>>>> >>>> exported over IIO.
>>>>> >>>>
>>>>> >>>> But, these sensors seem to not be updating at all with a 4.4-rc5+
>>>>> >>>> kernel (a
>>>>> >>>> set of patches from https://lkml.org/lkml/2015/11/30/441 applied to
>>>>> >>>> Linus'
>>>>> >>>> tree).
>>>>> >>>>
>>>>> >>>> The odd part is at some point in messing with this, I'm fairly sure
>>>>> >>>> it did work!
>>>>> >>>> That is,
>>>>> >>>>
>>>>> >>>> `watch -n 0.1 cat '/sys/bus/iio/devices/iio:device'*/*raw*`
>>>>> >>>
>>>>> >>> Can you send us a sample of the output? Also, would be
>>>>> >>> good to identify the exact driver for accel.
>>>>> >>
>>>>> >> cat /sys/bus/iio/devices/iio:device*/*raw*
>>>>> >> 65478
>>>>> >> 7
>>>>> >> 1023
>>>>> >> 0
>>>>> >> 0
>>>>> >> 0
>>>>> >> 100
>>>>> >> -539062
>>>>> >> -742187
>>>>> >> 1292968
>>>>> >> 1592
>>>>> >> 64932
>>>>> >> 2
>>>>> >> 275
>>>>> >> 0 0 0 0
>>>>> >>
>>>>> >> Now, I should say that I distinctly remember at some point waving my
>>>>> >> laptop around and seeing these values change ... but now they seem to
>>>>> >> be "stuck". Maybe it's a hardware issue or something special that
>>>>> >> WIndows does to leverage the IIO sensors?
>>>>> >>
>>>>> >>> Perhaps: cat /sys/bus/iio/devices/iio:device'*/name
>>>>> >>
>>>>> >> $ cat /sys/bus/iio/devices/iio:device*/name
>>>>> >> accel_3d
>>>>> >
>>>>> > Can you list the directory of iio:device with this name (it is:
>>>>> > drivers/iio/accel/hid-sensor-accel-3d.c).
>>>>> > This is something you will be looking at for accel debugging, but it
>>>>> > seems more like
>>>>> > standard
>>>>>
>>>>> /sys/bus/iio/devices/iio:device0/name
>>>>> gyro_3d
>>>>> /sys/bus/iio/devices/iio:device1/name
>>>>> dev_rotation
>>>>> /sys/bus/iio/devices/iio:device2/name
>>>>> als
>>>>> /sys/bus/iio/devices/iio:device3/name
>>>>> magn_3d
>>>>> /sys/bus/iio/devices/iio:device4/name
>>>>> accel_3d
>>>>> /sys/bus/iio/devices/iio:device5/name
>>>>> incli_3d
>>>>>
>>>>> are all the IIO sensors, sorry about that!
>>>>>
>>>>
>>>> I was more thinking what else is in iio:device4 directory, so that we can
>>>> see if it was initialized OK. Can you also grep the dmesg for any errors?
>>>
>>> Well, I just noticed the device #s are not consistent boot-to-boot, so
>>> this time it was device0. Trimming out the directories:
>>>
>
> This is correct/intended. You need to confirm "deviceX/name" each time.
Got it!
>>> /sys/bus/iio/devices/iio:device0/buffer
>>> cat: /sys/bus/iio/devices/iio:device0/buffer: Is a directory
>>> /sys/bus/iio/devices/iio:device0/dev
>>> 250:0
>>> /sys/bus/iio/devices/iio:device0/in_accel_hysteresis
>>> cat: /sys/bus/iio/devices/iio:device0/in_accel_hysteresis: Invalid argument
>>> /sys/bus/iio/devices/iio:device0/in_accel_offset
>>> 0
>>> /sys/bus/iio/devices/iio:device0/in_accel_sampling_frequency
>>> 8.000000
>>> /sys/bus/iio/devices/iio:device0/in_accel_scale
>>> 0.009806
>>> /sys/bus/iio/devices/iio:device0/in_accel_x_raw
>>> 65478
>>> /sys/bus/iio/devices/iio:device0/in_accel_y_raw
>>> 7
>>> /sys/bus/iio/devices/iio:device0/in_accel_z_raw
>>> 1023
>
> This seems like a valid number 1023 * 0.009806 = 10,031 m/s2 but X does not.
Ok...
>>> /sys/bus/iio/devices/iio:device0/name
>>> accel_3d
>>> /sys/bus/iio/devices/iio:device0/uevent
>>> MAJOR=250
>>> MINOR=0
>>> DEVNAME=iio:device0
>>> DEVTYPE=iio_device
>>>
>>> Another thing I just noticed:
>>>
>>> /sys/bus/iio/devices/iio:device0/buffer/enable
>>> 0
>
> This is buffer enable not chip enable. You can write 1 to that so it
> will be enables
> (echo "1" > /sys/bus/iio/devices/.../buffer/enable) and see what
> happens. It might be
> that it needs buffer to update properly (I haven't checked the code).
Doesn't immediately seem to make a difference.
>>>
>>> The only error I'm getting consistently is:
>>>
>>> [ 1.115327] i2c_hid i2c-ITE8396:00: error in i2c_hid_init_report
>>> size:19 / ret_size:18
>>>
>>> which I don't think is relevant, but I might be wrong.
>
> If accel is i2c this might be a relevant error - and probe would also
> not fail, but error would
> repeat itself each time probably Maybe track where that line is in
> i2c_hid and see what it
> could mean.
i2c_hid i2c-ITE8396:00: report (len=19): 12 00 5a ff ff ff ff ff ff ff
ff ff ff ff ff ff ff ff 06
i2c_hid i2c-ITE8396:00: error in i2c_hid_init_report size:19 / ret_size:18
So it seems like the device indicates an expected return size of 18,
but actually gives 19 bytes.
I don't know anything about i2c, but i'll dig around.
On Thu, Dec 17, 2015 at 9:32 AM, Nish Aravamudan
<[email protected]> wrote:
> On Thu, Dec 17, 2015 at 12:41 AM, Crt Mori <[email protected]> wrote:
>> On 17 December 2015 at 06:27, Nish Aravamudan <[email protected]> wrote:
>>> On Wed, Dec 16, 2015 at 3:05 PM, Nish Aravamudan
>>> <[email protected]> wrote:
>>>> On Wed, Dec 16, 2015 at 2:55 PM, Crt Mori <[email protected]> wrote:
>>>>>
>>>>> On Dec 16, 2015 11:37 PM, "Nish Aravamudan" <[email protected]>
>>>>> wrote:
>>>>>>
>>>>>> Hi,
>>>>>>
>>>>>> On Wed, Dec 16, 2015 at 2:22 PM, Crt Mori <[email protected]> wrote:
>>>>>> > On 16 December 2015 at 22:41, Nish Aravamudan
>>>>>> > <[email protected]> wrote:
>>>>>> >> Hi Daniel,
>>>>>> >>
>>>>>> >> On Wed, Dec 16, 2015 at 1:43 AM, Daniel Baluta
>>>>>> >> <[email protected]> wrote:
>>>>>> >>> On Tue, Dec 15, 2015 at 9:19 PM, Nish Aravamudan
>>>>>> >>> <[email protected]> wrote:
>>>>>> >>>> So, I apologize in advance for this relatively vague report, but I'm
>>>>>> >>>> fairly sure
>>>>>> >>>> the Yoga 900 has an accelerometer amongst other sensors (ambient
>>>>>> >>>> light?)
>>>>>> >>>> exported over IIO.
>>>>>> >>>>
>>>>>> >>>> But, these sensors seem to not be updating at all with a 4.4-rc5+
>>>>>> >>>> kernel (a
>>>>>> >>>> set of patches from https://lkml.org/lkml/2015/11/30/441 applied to
>>>>>> >>>> Linus'
>>>>>> >>>> tree).
>>>>>> >>>>
>>>>>> >>>> The odd part is at some point in messing with this, I'm fairly sure
>>>>>> >>>> it did work!
>>>>>> >>>> That is,
>>>>>> >>>>
>>>>>> >>>> `watch -n 0.1 cat '/sys/bus/iio/devices/iio:device'*/*raw*`
>>>>>> >>>
>>>>>> >>> Can you send us a sample of the output? Also, would be
>>>>>> >>> good to identify the exact driver for accel.
>>>>>> >>
>>>>>> >> cat /sys/bus/iio/devices/iio:device*/*raw*
>>>>>> >> 65478
>>>>>> >> 7
>>>>>> >> 1023
>>>>>> >> 0
>>>>>> >> 0
>>>>>> >> 0
>>>>>> >> 100
>>>>>> >> -539062
>>>>>> >> -742187
>>>>>> >> 1292968
>>>>>> >> 1592
>>>>>> >> 64932
>>>>>> >> 2
>>>>>> >> 275
>>>>>> >> 0 0 0 0
>>>>>> >>
>>>>>> >> Now, I should say that I distinctly remember at some point waving my
>>>>>> >> laptop around and seeing these values change ... but now they seem to
>>>>>> >> be "stuck". Maybe it's a hardware issue or something special that
>>>>>> >> WIndows does to leverage the IIO sensors?
>>>>>> >>
>>>>>> >>> Perhaps: cat /sys/bus/iio/devices/iio:device'*/name
>>>>>> >>
>>>>>> >> $ cat /sys/bus/iio/devices/iio:device*/name
>>>>>> >> accel_3d
>>>>>> >
>>>>>> > Can you list the directory of iio:device with this name (it is:
>>>>>> > drivers/iio/accel/hid-sensor-accel-3d.c).
>>>>>> > This is something you will be looking at for accel debugging, but it
>>>>>> > seems more like
>>>>>> > standard
>>>>>>
>>>>>> /sys/bus/iio/devices/iio:device0/name
>>>>>> gyro_3d
>>>>>> /sys/bus/iio/devices/iio:device1/name
>>>>>> dev_rotation
>>>>>> /sys/bus/iio/devices/iio:device2/name
>>>>>> als
>>>>>> /sys/bus/iio/devices/iio:device3/name
>>>>>> magn_3d
>>>>>> /sys/bus/iio/devices/iio:device4/name
>>>>>> accel_3d
>>>>>> /sys/bus/iio/devices/iio:device5/name
>>>>>> incli_3d
>>>>>>
>>>>>> are all the IIO sensors, sorry about that!
>>>>>>
>>>>>
>>>>> I was more thinking what else is in iio:device4 directory, so that we can
>>>>> see if it was initialized OK. Can you also grep the dmesg for any errors?
>>>>
>>>> Well, I just noticed the device #s are not consistent boot-to-boot, so
>>>> this time it was device0. Trimming out the directories:
>>>>
>>
>> This is correct/intended. You need to confirm "deviceX/name" each time.
>
> Got it!
>
>>>> /sys/bus/iio/devices/iio:device0/buffer
>>>> cat: /sys/bus/iio/devices/iio:device0/buffer: Is a directory
>>>> /sys/bus/iio/devices/iio:device0/dev
>>>> 250:0
>>>> /sys/bus/iio/devices/iio:device0/in_accel_hysteresis
>>>> cat: /sys/bus/iio/devices/iio:device0/in_accel_hysteresis: Invalid argument
>>>> /sys/bus/iio/devices/iio:device0/in_accel_offset
>>>> 0
>>>> /sys/bus/iio/devices/iio:device0/in_accel_sampling_frequency
>>>> 8.000000
>>>> /sys/bus/iio/devices/iio:device0/in_accel_scale
>>>> 0.009806
>>>> /sys/bus/iio/devices/iio:device0/in_accel_x_raw
>>>> 65478
>>>> /sys/bus/iio/devices/iio:device0/in_accel_y_raw
>>>> 7
>>>> /sys/bus/iio/devices/iio:device0/in_accel_z_raw
>>>> 1023
>>
>> This seems like a valid number 1023 * 0.009806 = 10,031 m/s2 but X does not.
>
> Ok...
>
>>>> /sys/bus/iio/devices/iio:device0/name
>>>> accel_3d
>>>> /sys/bus/iio/devices/iio:device0/uevent
>>>> MAJOR=250
>>>> MINOR=0
>>>> DEVNAME=iio:device0
>>>> DEVTYPE=iio_device
>>>>
>>>> Another thing I just noticed:
>>>>
>>>> /sys/bus/iio/devices/iio:device0/buffer/enable
>>>> 0
>>
>> This is buffer enable not chip enable. You can write 1 to that so it
>> will be enables
>> (echo "1" > /sys/bus/iio/devices/.../buffer/enable) and see what
>> happens. It might be
>> that it needs buffer to update properly (I haven't checked the code).
>
> Doesn't immediately seem to make a difference.
>
>>>>
>>>> The only error I'm getting consistently is:
>>>>
>>>> [ 1.115327] i2c_hid i2c-ITE8396:00: error in i2c_hid_init_report
>>>> size:19 / ret_size:18
>>>>
>>>> which I don't think is relevant, but I might be wrong.
>>
>> If accel is i2c this might be a relevant error - and probe would also
>> not fail, but error would
>> repeat itself each time probably Maybe track where that line is in
>> i2c_hid and see what it
>> could mean.
>
> i2c_hid i2c-ITE8396:00: report (len=19): 12 00 5a ff ff ff ff ff ff ff
> ff ff ff ff ff ff ff ff 06
> i2c_hid i2c-ITE8396:00: error in i2c_hid_init_report size:19 / ret_size:18
>
> So it seems like the device indicates an expected return size of 18,
> but actually gives 19 bytes.
>
> I don't know anything about i2c, but i'll dig around.
Another thought I had, reading through Google results for other Yoga
laptops, the sensor device showed up in lsusb. Would I expect to see
any such device in lsusb for the Yoga 900? I only get:
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 003: ID 8087:0a2b Intel Corp.
Bus 001 Device 002: ID 13d3:5664 IMC Networks
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-Nish
On 17 December 2015 at 19:10, Nish Aravamudan <[email protected]> wrote:
> On Thu, Dec 17, 2015 at 9:32 AM, Nish Aravamudan
> <[email protected]> wrote:
>> On Thu, Dec 17, 2015 at 12:41 AM, Crt Mori <[email protected]> wrote:
>>> On 17 December 2015 at 06:27, Nish Aravamudan <[email protected]> wrote:
>>>> On Wed, Dec 16, 2015 at 3:05 PM, Nish Aravamudan
>>>> <[email protected]> wrote:
>>>>> On Wed, Dec 16, 2015 at 2:55 PM, Crt Mori <[email protected]> wrote:
>>>>>>
>>>>>> On Dec 16, 2015 11:37 PM, "Nish Aravamudan" <[email protected]>
>>>>>> wrote:
>>>>>>>
>>>>>>> Hi,
>>>>>>>
>>>>>>> On Wed, Dec 16, 2015 at 2:22 PM, Crt Mori <[email protected]> wrote:
>>>>>>> > On 16 December 2015 at 22:41, Nish Aravamudan
>>>>>>> > <[email protected]> wrote:
>>>>>>> >> Hi Daniel,
>>>>>>> >>
>>>>>>> >> On Wed, Dec 16, 2015 at 1:43 AM, Daniel Baluta
>>>>>>> >> <[email protected]> wrote:
>>>>>>> >>> On Tue, Dec 15, 2015 at 9:19 PM, Nish Aravamudan
>>>>>>> >>> <[email protected]> wrote:
>>>>>>> >>>> So, I apologize in advance for this relatively vague report, but I'm
>>>>>>> >>>> fairly sure
>>>>>>> >>>> the Yoga 900 has an accelerometer amongst other sensors (ambient
>>>>>>> >>>> light?)
>>>>>>> >>>> exported over IIO.
>>>>>>> >>>>
>>>>>>> >>>> But, these sensors seem to not be updating at all with a 4.4-rc5+
>>>>>>> >>>> kernel (a
>>>>>>> >>>> set of patches from https://lkml.org/lkml/2015/11/30/441 applied to
>>>>>>> >>>> Linus'
>>>>>>> >>>> tree).
>>>>>>> >>>>
>>>>>>> >>>> The odd part is at some point in messing with this, I'm fairly sure
>>>>>>> >>>> it did work!
>>>>>>> >>>> That is,
>>>>>>> >>>>
>>>>>>> >>>> `watch -n 0.1 cat '/sys/bus/iio/devices/iio:device'*/*raw*`
>>>>>>> >>>
>>>>>>> >>> Can you send us a sample of the output? Also, would be
>>>>>>> >>> good to identify the exact driver for accel.
>>>>>>> >>
>>>>>>> >> cat /sys/bus/iio/devices/iio:device*/*raw*
>>>>>>> >> 65478
>>>>>>> >> 7
>>>>>>> >> 1023
>>>>>>> >> 0
>>>>>>> >> 0
>>>>>>> >> 0
>>>>>>> >> 100
>>>>>>> >> -539062
>>>>>>> >> -742187
>>>>>>> >> 1292968
>>>>>>> >> 1592
>>>>>>> >> 64932
>>>>>>> >> 2
>>>>>>> >> 275
>>>>>>> >> 0 0 0 0
>>>>>>> >>
>>>>>>> >> Now, I should say that I distinctly remember at some point waving my
>>>>>>> >> laptop around and seeing these values change ... but now they seem to
>>>>>>> >> be "stuck". Maybe it's a hardware issue or something special that
>>>>>>> >> WIndows does to leverage the IIO sensors?
>>>>>>> >>
>>>>>>> >>> Perhaps: cat /sys/bus/iio/devices/iio:device'*/name
>>>>>>> >>
>>>>>>> >> $ cat /sys/bus/iio/devices/iio:device*/name
>>>>>>> >> accel_3d
>>>>>>> >
>>>>>>> > Can you list the directory of iio:device with this name (it is:
>>>>>>> > drivers/iio/accel/hid-sensor-accel-3d.c).
>>>>>>> > This is something you will be looking at for accel debugging, but it
>>>>>>> > seems more like
>>>>>>> > standard
>>>>>>>
>>>>>>> /sys/bus/iio/devices/iio:device0/name
>>>>>>> gyro_3d
>>>>>>> /sys/bus/iio/devices/iio:device1/name
>>>>>>> dev_rotation
>>>>>>> /sys/bus/iio/devices/iio:device2/name
>>>>>>> als
>>>>>>> /sys/bus/iio/devices/iio:device3/name
>>>>>>> magn_3d
>>>>>>> /sys/bus/iio/devices/iio:device4/name
>>>>>>> accel_3d
>>>>>>> /sys/bus/iio/devices/iio:device5/name
>>>>>>> incli_3d
>>>>>>>
>>>>>>> are all the IIO sensors, sorry about that!
>>>>>>>
>>>>>>
>>>>>> I was more thinking what else is in iio:device4 directory, so that we can
>>>>>> see if it was initialized OK. Can you also grep the dmesg for any errors?
>>>>>
>>>>> Well, I just noticed the device #s are not consistent boot-to-boot, so
>>>>> this time it was device0. Trimming out the directories:
>>>>>
>>>
>>> This is correct/intended. You need to confirm "deviceX/name" each time.
>>
>> Got it!
>>
>>>>> /sys/bus/iio/devices/iio:device0/buffer
>>>>> cat: /sys/bus/iio/devices/iio:device0/buffer: Is a directory
>>>>> /sys/bus/iio/devices/iio:device0/dev
>>>>> 250:0
>>>>> /sys/bus/iio/devices/iio:device0/in_accel_hysteresis
>>>>> cat: /sys/bus/iio/devices/iio:device0/in_accel_hysteresis: Invalid argument
>>>>> /sys/bus/iio/devices/iio:device0/in_accel_offset
>>>>> 0
>>>>> /sys/bus/iio/devices/iio:device0/in_accel_sampling_frequency
>>>>> 8.000000
>>>>> /sys/bus/iio/devices/iio:device0/in_accel_scale
>>>>> 0.009806
>>>>> /sys/bus/iio/devices/iio:device0/in_accel_x_raw
>>>>> 65478
>>>>> /sys/bus/iio/devices/iio:device0/in_accel_y_raw
>>>>> 7
>>>>> /sys/bus/iio/devices/iio:device0/in_accel_z_raw
>>>>> 1023
>>>
>>> This seems like a valid number 1023 * 0.009806 = 10,031 m/s2 but X does not.
>>
>> Ok...
>>
>>>>> /sys/bus/iio/devices/iio:device0/name
>>>>> accel_3d
>>>>> /sys/bus/iio/devices/iio:device0/uevent
>>>>> MAJOR=250
>>>>> MINOR=0
>>>>> DEVNAME=iio:device0
>>>>> DEVTYPE=iio_device
>>>>>
>>>>> Another thing I just noticed:
>>>>>
>>>>> /sys/bus/iio/devices/iio:device0/buffer/enable
>>>>> 0
>>>
>>> This is buffer enable not chip enable. You can write 1 to that so it
>>> will be enables
>>> (echo "1" > /sys/bus/iio/devices/.../buffer/enable) and see what
>>> happens. It might be
>>> that it needs buffer to update properly (I haven't checked the code).
>>
>> Doesn't immediately seem to make a difference.
>>
>>>>>
>>>>> The only error I'm getting consistently is:
>>>>>
>>>>> [ 1.115327] i2c_hid i2c-ITE8396:00: error in i2c_hid_init_report
>>>>> size:19 / ret_size:18
>>>>>
>>>>> which I don't think is relevant, but I might be wrong.
>>>
>>> If accel is i2c this might be a relevant error - and probe would also
>>> not fail, but error would
>>> repeat itself each time probably Maybe track where that line is in
>>> i2c_hid and see what it
>>> could mean.
>>
>> i2c_hid i2c-ITE8396:00: report (len=19): 12 00 5a ff ff ff ff ff ff ff
>> ff ff ff ff ff ff ff ff 06
>> i2c_hid i2c-ITE8396:00: error in i2c_hid_init_report size:19 / ret_size:18
>>
>> So it seems like the device indicates an expected return size of 18,
>> but actually gives 19 bytes.
>>
>> I don't know anything about i2c, but i'll dig around.
>
There is chance to read the /sys/bus/i2c/... device (maybe see the
address there?) directly.
However I would expect an i2c error each time you try to read a raw
value in driver if there would
be some. I hope someone more experienced can chime in...
> Another thought I had, reading through Google results for other Yoga
> laptops, the sensor device showed up in lsusb. Would I expect to see
> any such device in lsusb for the Yoga 900? I only get:
>
> Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
> Bus 001 Device 003: ID 8087:0a2b Intel Corp.
> Bus 001 Device 002: ID 13d3:5664 IMC Networks
> Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
>
I somehow doubt that accel is an usb device (which is what lsusb would
show), but if it
does then it should not show in iio.
There is however iioutils package which is around same as lsusb and
might be worth checking
out for you.
On Thu, Dec 17, 2015 at 10:38 AM, Crt Mori <[email protected]> wrote:
> On 17 December 2015 at 19:10, Nish Aravamudan <[email protected]> wrote:
>> On Thu, Dec 17, 2015 at 9:32 AM, Nish Aravamudan
>> <[email protected]> wrote:
>>> On Thu, Dec 17, 2015 at 12:41 AM, Crt Mori <[email protected]> wrote:
>>>> On 17 December 2015 at 06:27, Nish Aravamudan <[email protected]> wrote:
>>>>> On Wed, Dec 16, 2015 at 3:05 PM, Nish Aravamudan
>>>>> <[email protected]> wrote:
>>>>>> On Wed, Dec 16, 2015 at 2:55 PM, Crt Mori <[email protected]> wrote:
>>>>>>>
>>>>>>> On Dec 16, 2015 11:37 PM, "Nish Aravamudan" <[email protected]>
>>>>>>> wrote:
>>>>>>>>
>>>>>>>> Hi,
>>>>>>>>
>>>>>>>> On Wed, Dec 16, 2015 at 2:22 PM, Crt Mori <[email protected]> wrote:
>>>>>>>> > On 16 December 2015 at 22:41, Nish Aravamudan
>>>>>>>> > <[email protected]> wrote:
>>>>>>>> >> Hi Daniel,
>>>>>>>> >>
>>>>>>>> >> On Wed, Dec 16, 2015 at 1:43 AM, Daniel Baluta
>>>>>>>> >> <[email protected]> wrote:
>>>>>>>> >>> On Tue, Dec 15, 2015 at 9:19 PM, Nish Aravamudan
>>>>>>>> >>> <[email protected]> wrote:
>>>>>>>> >>>> So, I apologize in advance for this relatively vague report, but I'm
>>>>>>>> >>>> fairly sure
>>>>>>>> >>>> the Yoga 900 has an accelerometer amongst other sensors (ambient
>>>>>>>> >>>> light?)
>>>>>>>> >>>> exported over IIO.
>>>>>>>> >>>>
>>>>>>>> >>>> But, these sensors seem to not be updating at all with a 4.4-rc5+
>>>>>>>> >>>> kernel (a
>>>>>>>> >>>> set of patches from https://lkml.org/lkml/2015/11/30/441 applied to
>>>>>>>> >>>> Linus'
>>>>>>>> >>>> tree).
>>>>>>>> >>>>
>>>>>>>> >>>> The odd part is at some point in messing with this, I'm fairly sure
>>>>>>>> >>>> it did work!
>>>>>>>> >>>> That is,
>>>>>>>> >>>>
>>>>>>>> >>>> `watch -n 0.1 cat '/sys/bus/iio/devices/iio:device'*/*raw*`
>>>>>>>> >>>
>>>>>>>> >>> Can you send us a sample of the output? Also, would be
>>>>>>>> >>> good to identify the exact driver for accel.
>>>>>>>> >>
>>>>>>>> >> cat /sys/bus/iio/devices/iio:device*/*raw*
>>>>>>>> >> 65478
>>>>>>>> >> 7
>>>>>>>> >> 1023
>>>>>>>> >> 0
>>>>>>>> >> 0
>>>>>>>> >> 0
>>>>>>>> >> 100
>>>>>>>> >> -539062
>>>>>>>> >> -742187
>>>>>>>> >> 1292968
>>>>>>>> >> 1592
>>>>>>>> >> 64932
>>>>>>>> >> 2
>>>>>>>> >> 275
>>>>>>>> >> 0 0 0 0
>>>>>>>> >>
>>>>>>>> >> Now, I should say that I distinctly remember at some point waving my
>>>>>>>> >> laptop around and seeing these values change ... but now they seem to
>>>>>>>> >> be "stuck". Maybe it's a hardware issue or something special that
>>>>>>>> >> WIndows does to leverage the IIO sensors?
>>>>>>>> >>
>>>>>>>> >>> Perhaps: cat /sys/bus/iio/devices/iio:device'*/name
>>>>>>>> >>
>>>>>>>> >> $ cat /sys/bus/iio/devices/iio:device*/name
>>>>>>>> >> accel_3d
>>>>>>>> >
>>>>>>>> > Can you list the directory of iio:device with this name (it is:
>>>>>>>> > drivers/iio/accel/hid-sensor-accel-3d.c).
>>>>>>>> > This is something you will be looking at for accel debugging, but it
>>>>>>>> > seems more like
>>>>>>>> > standard
>>>>>>>>
>>>>>>>> /sys/bus/iio/devices/iio:device0/name
>>>>>>>> gyro_3d
>>>>>>>> /sys/bus/iio/devices/iio:device1/name
>>>>>>>> dev_rotation
>>>>>>>> /sys/bus/iio/devices/iio:device2/name
>>>>>>>> als
>>>>>>>> /sys/bus/iio/devices/iio:device3/name
>>>>>>>> magn_3d
>>>>>>>> /sys/bus/iio/devices/iio:device4/name
>>>>>>>> accel_3d
>>>>>>>> /sys/bus/iio/devices/iio:device5/name
>>>>>>>> incli_3d
>>>>>>>>
>>>>>>>> are all the IIO sensors, sorry about that!
>>>>>>>>
>>>>>>>
>>>>>>> I was more thinking what else is in iio:device4 directory, so that we can
>>>>>>> see if it was initialized OK. Can you also grep the dmesg for any errors?
>>>>>>
>>>>>> Well, I just noticed the device #s are not consistent boot-to-boot, so
>>>>>> this time it was device0. Trimming out the directories:
>>>>>>
>>>>
>>>> This is correct/intended. You need to confirm "deviceX/name" each time.
>>>
>>> Got it!
>>>
>>>>>> /sys/bus/iio/devices/iio:device0/buffer
>>>>>> cat: /sys/bus/iio/devices/iio:device0/buffer: Is a directory
>>>>>> /sys/bus/iio/devices/iio:device0/dev
>>>>>> 250:0
>>>>>> /sys/bus/iio/devices/iio:device0/in_accel_hysteresis
>>>>>> cat: /sys/bus/iio/devices/iio:device0/in_accel_hysteresis: Invalid argument
>>>>>> /sys/bus/iio/devices/iio:device0/in_accel_offset
>>>>>> 0
>>>>>> /sys/bus/iio/devices/iio:device0/in_accel_sampling_frequency
>>>>>> 8.000000
>>>>>> /sys/bus/iio/devices/iio:device0/in_accel_scale
>>>>>> 0.009806
>>>>>> /sys/bus/iio/devices/iio:device0/in_accel_x_raw
>>>>>> 65478
>>>>>> /sys/bus/iio/devices/iio:device0/in_accel_y_raw
>>>>>> 7
>>>>>> /sys/bus/iio/devices/iio:device0/in_accel_z_raw
>>>>>> 1023
>>>>
>>>> This seems like a valid number 1023 * 0.009806 = 10,031 m/s2 but X does not.
>>>
>>> Ok...
>>>
>>>>>> /sys/bus/iio/devices/iio:device0/name
>>>>>> accel_3d
>>>>>> /sys/bus/iio/devices/iio:device0/uevent
>>>>>> MAJOR=250
>>>>>> MINOR=0
>>>>>> DEVNAME=iio:device0
>>>>>> DEVTYPE=iio_device
>>>>>>
>>>>>> Another thing I just noticed:
>>>>>>
>>>>>> /sys/bus/iio/devices/iio:device0/buffer/enable
>>>>>> 0
>>>>
>>>> This is buffer enable not chip enable. You can write 1 to that so it
>>>> will be enables
>>>> (echo "1" > /sys/bus/iio/devices/.../buffer/enable) and see what
>>>> happens. It might be
>>>> that it needs buffer to update properly (I haven't checked the code).
>>>
>>> Doesn't immediately seem to make a difference.
>>>
>>>>>>
>>>>>> The only error I'm getting consistently is:
>>>>>>
>>>>>> [ 1.115327] i2c_hid i2c-ITE8396:00: error in i2c_hid_init_report
>>>>>> size:19 / ret_size:18
>>>>>>
>>>>>> which I don't think is relevant, but I might be wrong.
>>>>
>>>> If accel is i2c this might be a relevant error - and probe would also
>>>> not fail, but error would
>>>> repeat itself each time probably Maybe track where that line is in
>>>> i2c_hid and see what it
>>>> could mean.
>>>
>>> i2c_hid i2c-ITE8396:00: report (len=19): 12 00 5a ff ff ff ff ff ff ff
>>> ff ff ff ff ff ff ff ff 06
>>> i2c_hid i2c-ITE8396:00: error in i2c_hid_init_report size:19 / ret_size:18
>>>
>>> So it seems like the device indicates an expected return size of 18,
>>> but actually gives 19 bytes.
>>>
>>> I don't know anything about i2c, but i'll dig around.
>>
>
> There is chance to read the /sys/bus/i2c/... device (maybe see the
> address there?) directly.
> However I would expect an i2c error each time you try to read a raw
> value in driver if there would
> be some. I hope someone more experienced can chime in...
>
>> Another thought I had, reading through Google results for other Yoga
>> laptops, the sensor device showed up in lsusb. Would I expect to see
>> any such device in lsusb for the Yoga 900? I only get:
>>
>> Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
>> Bus 001 Device 003: ID 8087:0a2b Intel Corp.
>> Bus 001 Device 002: ID 13d3:5664 IMC Networks
>> Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
>>
>
> I somehow doubt that accel is an usb device (which is what lsusb would
> show), but if it
> does then it should not show in iio.
> There is however iioutils package which is around same as lsusb and
> might be worth checking
> out for you.
Ah! So I have no idea what changed. I cloned the iioutils git tree
from SF and now the sensors are reporting values and dmesg is
reporting:
[13872.936769] hid-sensor-hub 0018:048D:8396.0001: No report with id
0xffffffff found
-Nish
On Thu, Dec 17, 2015 at 12:05 PM, Nish Aravamudan
<[email protected]> wrote:
> On Thu, Dec 17, 2015 at 10:38 AM, Crt Mori <[email protected]> wrote:
>> On 17 December 2015 at 19:10, Nish Aravamudan <[email protected]> wrote:
>>> On Thu, Dec 17, 2015 at 9:32 AM, Nish Aravamudan
>>> <[email protected]> wrote:
>>>> On Thu, Dec 17, 2015 at 12:41 AM, Crt Mori <[email protected]> wrote:
>>>>> On 17 December 2015 at 06:27, Nish Aravamudan <[email protected]> wrote:
>>>>>> On Wed, Dec 16, 2015 at 3:05 PM, Nish Aravamudan
>>>>>> <[email protected]> wrote:
>>>>>>> On Wed, Dec 16, 2015 at 2:55 PM, Crt Mori <[email protected]> wrote:
>>>>>>>>
>>>>>>>> On Dec 16, 2015 11:37 PM, "Nish Aravamudan" <[email protected]>
>>>>>>>> wrote:
>>>>>>>>>
>>>>>>>>> Hi,
>>>>>>>>>
>>>>>>>>> On Wed, Dec 16, 2015 at 2:22 PM, Crt Mori <[email protected]> wrote:
>>>>>>>>> > On 16 December 2015 at 22:41, Nish Aravamudan
>>>>>>>>> > <[email protected]> wrote:
>>>>>>>>> >> Hi Daniel,
>>>>>>>>> >>
>>>>>>>>> >> On Wed, Dec 16, 2015 at 1:43 AM, Daniel Baluta
>>>>>>>>> >> <[email protected]> wrote:
>>>>>>>>> >>> On Tue, Dec 15, 2015 at 9:19 PM, Nish Aravamudan
>>>>>>>>> >>> <[email protected]> wrote:
>>>>>>>>> >>>> So, I apologize in advance for this relatively vague report, but I'm
>>>>>>>>> >>>> fairly sure
>>>>>>>>> >>>> the Yoga 900 has an accelerometer amongst other sensors (ambient
>>>>>>>>> >>>> light?)
>>>>>>>>> >>>> exported over IIO.
>>>>>>>>> >>>>
>>>>>>>>> >>>> But, these sensors seem to not be updating at all with a 4.4-rc5+
>>>>>>>>> >>>> kernel (a
>>>>>>>>> >>>> set of patches from https://lkml.org/lkml/2015/11/30/441 applied to
>>>>>>>>> >>>> Linus'
>>>>>>>>> >>>> tree).
>>>>>>>>> >>>>
>>>>>>>>> >>>> The odd part is at some point in messing with this, I'm fairly sure
>>>>>>>>> >>>> it did work!
>>>>>>>>> >>>> That is,
>>>>>>>>> >>>>
>>>>>>>>> >>>> `watch -n 0.1 cat '/sys/bus/iio/devices/iio:device'*/*raw*`
>>>>>>>>> >>>
>>>>>>>>> >>> Can you send us a sample of the output? Also, would be
>>>>>>>>> >>> good to identify the exact driver for accel.
>>>>>>>>> >>
>>>>>>>>> >> cat /sys/bus/iio/devices/iio:device*/*raw*
>>>>>>>>> >> 65478
>>>>>>>>> >> 7
>>>>>>>>> >> 1023
>>>>>>>>> >> 0
>>>>>>>>> >> 0
>>>>>>>>> >> 0
>>>>>>>>> >> 100
>>>>>>>>> >> -539062
>>>>>>>>> >> -742187
>>>>>>>>> >> 1292968
>>>>>>>>> >> 1592
>>>>>>>>> >> 64932
>>>>>>>>> >> 2
>>>>>>>>> >> 275
>>>>>>>>> >> 0 0 0 0
>>>>>>>>> >>
>>>>>>>>> >> Now, I should say that I distinctly remember at some point waving my
>>>>>>>>> >> laptop around and seeing these values change ... but now they seem to
>>>>>>>>> >> be "stuck". Maybe it's a hardware issue or something special that
>>>>>>>>> >> WIndows does to leverage the IIO sensors?
>>>>>>>>> >>
>>>>>>>>> >>> Perhaps: cat /sys/bus/iio/devices/iio:device'*/name
>>>>>>>>> >>
>>>>>>>>> >> $ cat /sys/bus/iio/devices/iio:device*/name
>>>>>>>>> >> accel_3d
>>>>>>>>> >
>>>>>>>>> > Can you list the directory of iio:device with this name (it is:
>>>>>>>>> > drivers/iio/accel/hid-sensor-accel-3d.c).
>>>>>>>>> > This is something you will be looking at for accel debugging, but it
>>>>>>>>> > seems more like
>>>>>>>>> > standard
>>>>>>>>>
>>>>>>>>> /sys/bus/iio/devices/iio:device0/name
>>>>>>>>> gyro_3d
>>>>>>>>> /sys/bus/iio/devices/iio:device1/name
>>>>>>>>> dev_rotation
>>>>>>>>> /sys/bus/iio/devices/iio:device2/name
>>>>>>>>> als
>>>>>>>>> /sys/bus/iio/devices/iio:device3/name
>>>>>>>>> magn_3d
>>>>>>>>> /sys/bus/iio/devices/iio:device4/name
>>>>>>>>> accel_3d
>>>>>>>>> /sys/bus/iio/devices/iio:device5/name
>>>>>>>>> incli_3d
>>>>>>>>>
>>>>>>>>> are all the IIO sensors, sorry about that!
>>>>>>>>>
>>>>>>>>
>>>>>>>> I was more thinking what else is in iio:device4 directory, so that we can
>>>>>>>> see if it was initialized OK. Can you also grep the dmesg for any errors?
>>>>>>>
>>>>>>> Well, I just noticed the device #s are not consistent boot-to-boot, so
>>>>>>> this time it was device0. Trimming out the directories:
>>>>>>>
>>>>>
>>>>> This is correct/intended. You need to confirm "deviceX/name" each time.
>>>>
>>>> Got it!
>>>>
>>>>>>> /sys/bus/iio/devices/iio:device0/buffer
>>>>>>> cat: /sys/bus/iio/devices/iio:device0/buffer: Is a directory
>>>>>>> /sys/bus/iio/devices/iio:device0/dev
>>>>>>> 250:0
>>>>>>> /sys/bus/iio/devices/iio:device0/in_accel_hysteresis
>>>>>>> cat: /sys/bus/iio/devices/iio:device0/in_accel_hysteresis: Invalid argument
>>>>>>> /sys/bus/iio/devices/iio:device0/in_accel_offset
>>>>>>> 0
>>>>>>> /sys/bus/iio/devices/iio:device0/in_accel_sampling_frequency
>>>>>>> 8.000000
>>>>>>> /sys/bus/iio/devices/iio:device0/in_accel_scale
>>>>>>> 0.009806
>>>>>>> /sys/bus/iio/devices/iio:device0/in_accel_x_raw
>>>>>>> 65478
>>>>>>> /sys/bus/iio/devices/iio:device0/in_accel_y_raw
>>>>>>> 7
>>>>>>> /sys/bus/iio/devices/iio:device0/in_accel_z_raw
>>>>>>> 1023
>>>>>
>>>>> This seems like a valid number 1023 * 0.009806 = 10,031 m/s2 but X does not.
>>>>
>>>> Ok...
>>>>
>>>>>>> /sys/bus/iio/devices/iio:device0/name
>>>>>>> accel_3d
>>>>>>> /sys/bus/iio/devices/iio:device0/uevent
>>>>>>> MAJOR=250
>>>>>>> MINOR=0
>>>>>>> DEVNAME=iio:device0
>>>>>>> DEVTYPE=iio_device
>>>>>>>
>>>>>>> Another thing I just noticed:
>>>>>>>
>>>>>>> /sys/bus/iio/devices/iio:device0/buffer/enable
>>>>>>> 0
>>>>>
>>>>> This is buffer enable not chip enable. You can write 1 to that so it
>>>>> will be enables
>>>>> (echo "1" > /sys/bus/iio/devices/.../buffer/enable) and see what
>>>>> happens. It might be
>>>>> that it needs buffer to update properly (I haven't checked the code).
>>>>
>>>> Doesn't immediately seem to make a difference.
>>>>
>>>>>>>
>>>>>>> The only error I'm getting consistently is:
>>>>>>>
>>>>>>> [ 1.115327] i2c_hid i2c-ITE8396:00: error in i2c_hid_init_report
>>>>>>> size:19 / ret_size:18
>>>>>>>
>>>>>>> which I don't think is relevant, but I might be wrong.
>>>>>
>>>>> If accel is i2c this might be a relevant error - and probe would also
>>>>> not fail, but error would
>>>>> repeat itself each time probably Maybe track where that line is in
>>>>> i2c_hid and see what it
>>>>> could mean.
>>>>
>>>> i2c_hid i2c-ITE8396:00: report (len=19): 12 00 5a ff ff ff ff ff ff ff
>>>> ff ff ff ff ff ff ff ff 06
>>>> i2c_hid i2c-ITE8396:00: error in i2c_hid_init_report size:19 / ret_size:18
>>>>
>>>> So it seems like the device indicates an expected return size of 18,
>>>> but actually gives 19 bytes.
>>>>
>>>> I don't know anything about i2c, but i'll dig around.
>>>
>>
>> There is chance to read the /sys/bus/i2c/... device (maybe see the
>> address there?) directly.
>> However I would expect an i2c error each time you try to read a raw
>> value in driver if there would
>> be some. I hope someone more experienced can chime in...
>>
>>> Another thought I had, reading through Google results for other Yoga
>>> laptops, the sensor device showed up in lsusb. Would I expect to see
>>> any such device in lsusb for the Yoga 900? I only get:
>>>
>>> Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
>>> Bus 001 Device 003: ID 8087:0a2b Intel Corp.
>>> Bus 001 Device 002: ID 13d3:5664 IMC Networks
>>> Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
>>>
>>
>> I somehow doubt that accel is an usb device (which is what lsusb would
>> show), but if it
>> does then it should not show in iio.
>> There is however iioutils package which is around same as lsusb and
>> might be worth checking
>> out for you.
>
> Ah! So I have no idea what changed. I cloned the iioutils git tree
> from SF and now the sensors are reporting values and dmesg is
> reporting:
>
> [13872.936769] hid-sensor-hub 0018:048D:8396.0001: No report with id
> 0xffffffff found
Ok, well, I'm pretty confused now. Maybe lsiio probed something
correctly to wake up the sensors. But now they work still after
reboot! The message above was because I had incorrectly applied the
Yoga/Yoga2 quirk to the 900 and it doesn't seem to be necessary.
Now to get iio-sensor-proxy to work :)
-Nish