This patchset modifies the GIC driver to allow it, on supported
platforms, to route IPI interrupts to FIQ. It then uses this
feature to implement arch_trigger_all_cpu_backtrace for arm.
In order to neatly deliver the changes for the arm we also
rearrange some of the existing x86 NMI code to make it architecture
neutral.
The patches have been runtime tested on both a system capable of
supporting FIQ (Freescale i.MX6) and one that cannot (Qualcomm
Snapdragon 600). In addition older versions of this patchset
have been tested on STiH416 and vexpress-a9. The changes to the x86
logic were tested using qemu.
v21:
* Change the way SGIs are raised to try to increase robustness starting
secondary cores. This is a theoretic fix for a regression reported
by Mark Rutland on vexpress-tc2 but it also allows us to remove
igroup0_shadow entirely since it is no longer needed.
* Fix a couple of variable names and add comments to describe the
hardware behavior better (Mark Rutland).
* Improved MULTI_IRQ_HANDLER support by clearing FIQs using
handle_arch_irq (Marc Zygnier).
* Fix gic_cpu_if_down() to ensure group 1 interrupts are disabled
then the interface is brought down.
For changes in v20 and earlier see:
http://thread.gmane.org/gmane.linux.kernel/1928465
Daniel Thompson (6):
irqchip: gic: Optimize locking in gic_raise_softirq
irqchip: gic: Make gic_raise_softirq FIQ-safe
irqchip: gic: Introduce plumbing for IPI FIQ
printk: Simple implementation for NMI backtracing
x86/nmi: Use common printk functions
ARM: Add support for on-demand backtrace of other CPUs
arch/arm/Kconfig | 1 +
arch/arm/include/asm/hardirq.h | 2 +-
arch/arm/include/asm/irq.h | 5 +
arch/arm/include/asm/smp.h | 3 +
arch/arm/kernel/smp.c | 82 +++++++++++++++
arch/arm/kernel/traps.c | 13 ++-
arch/x86/Kconfig | 1 +
arch/x86/kernel/apic/hw_nmi.c | 104 ++-----------------
drivers/irqchip/irq-gic.c | 220 +++++++++++++++++++++++++++++++++++++---
include/linux/irqchip/arm-gic.h | 6 ++
include/linux/printk.h | 20 ++++
init/Kconfig | 3 +
kernel/printk/Makefile | 1 +
kernel/printk/nmi_backtrace.c | 147 +++++++++++++++++++++++++++
14 files changed, 495 insertions(+), 113 deletions(-)
create mode 100644 kernel/printk/nmi_backtrace.c
--
2.4.3
Currently gic_raise_softirq() is locked using irq_controller_lock.
This lock is primarily used to make register read-modify-write sequences
atomic but gic_raise_softirq() uses it instead to ensure that the
big.LITTLE migration logic can figure out when it is safe to migrate
interrupts between physical cores.
This is sub-optimal in closely related ways:
1. No locking at all is required on systems where the b.L switcher is
not configured.
2. Finer grain locking can be used on systems where the b.L switcher is
present.
This patch resolves both of the above by introducing a separate finer
grain lock and providing conditionally compiled inlines to lock/unlock
it.
Signed-off-by: Daniel Thompson <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: Jason Cooper <[email protected]>
Cc: Russell King <[email protected]>
Cc: Marc Zyngier <[email protected]>
Acked-by: Nicolas Pitre <[email protected]>
---
drivers/irqchip/irq-gic.c | 36 +++++++++++++++++++++++++++++++++---
1 file changed, 33 insertions(+), 3 deletions(-)
diff --git a/drivers/irqchip/irq-gic.c b/drivers/irqchip/irq-gic.c
index 8d7e1c8b6d56..9ed278902d64 100644
--- a/drivers/irqchip/irq-gic.c
+++ b/drivers/irqchip/irq-gic.c
@@ -75,6 +75,27 @@ struct gic_chip_data {
static DEFINE_RAW_SPINLOCK(irq_controller_lock);
/*
+ * This lock is used by the big.LITTLE migration code to ensure no IPIs
+ * can be pended on the old core after the map has been updated.
+ */
+#ifdef CONFIG_BL_SWITCHER
+static DEFINE_RAW_SPINLOCK(cpu_map_migration_lock);
+
+static inline void gic_migration_lock(unsigned long *flags)
+{
+ raw_spin_lock_irqsave(&cpu_map_migration_lock, *flags);
+}
+
+static inline void gic_migration_unlock(unsigned long flags)
+{
+ raw_spin_unlock_irqrestore(&cpu_map_migration_lock, flags);
+}
+#else
+static inline void gic_migration_lock(unsigned long *flags) {}
+static inline void gic_migration_unlock(unsigned long flags) {}
+#endif
+
+/*
* The GIC mapping of CPU interfaces does not necessarily match
* the logical CPU numbering. Let's use a mapping as returned
* by the GIC itself.
@@ -627,7 +648,7 @@ static void gic_raise_softirq(const struct cpumask *mask, unsigned int irq)
int cpu;
unsigned long flags, map = 0;
- raw_spin_lock_irqsave(&irq_controller_lock, flags);
+ gic_migration_lock(&flags);
/* Convert our logical CPU mask into a physical one. */
for_each_cpu(cpu, mask)
@@ -642,7 +663,7 @@ static void gic_raise_softirq(const struct cpumask *mask, unsigned int irq)
/* this always happens on GIC0 */
writel_relaxed(map << 16 | irq, gic_data_dist_base(&gic_data[0]) + GIC_DIST_SOFTINT);
- raw_spin_unlock_irqrestore(&irq_controller_lock, flags);
+ gic_migration_unlock(flags);
}
#endif
@@ -713,8 +734,17 @@ void gic_migrate_target(unsigned int new_cpu_id)
raw_spin_lock(&irq_controller_lock);
- /* Update the target interface for this logical CPU */
+ /*
+ * Update the target interface for this logical CPU
+ *
+ * From the point we release the cpu_map_migration_lock any new
+ * SGIs will be pended on the new cpu which makes the set of SGIs
+ * pending on the old cpu static. That means we can defer the
+ * migration until after we have released the irq_controller_lock.
+ */
+ raw_spin_lock(&cpu_map_migration_lock);
gic_cpu_map[cpu] = 1 << new_cpu_id;
+ raw_spin_unlock(&cpu_map_migration_lock);
/*
* Find all the peripheral interrupts targetting the current
--
2.4.3
It is currently possible for FIQ handlers to re-enter gic_raise_softirq()
and lock up.
gic_raise_softirq()
lock(x);
-~-> FIQ
handle_fiq()
gic_raise_softirq()
lock(x); <-- Lockup
arch/arm/ uses IPIs to implement arch_irq_work_raise(), thus this issue
renders it difficult for FIQ handlers to safely defer work to less
restrictive calling contexts.
This patch fixes the problem by converting the cpu_map_migration_lock
into a rwlock making it safe to re-enter the function.
Note that having made it safe to re-enter gic_raise_softirq() we no
longer need to mask interrupts during gic_raise_softirq() because the
b.L migration is always performed from task context.
Signed-off-by: Daniel Thompson <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: Jason Cooper <[email protected]>
Cc: Russell King <[email protected]>
Cc: Marc Zyngier <[email protected]>
Acked-by: Nicolas Pitre <[email protected]>
---
drivers/irqchip/irq-gic.c | 38 +++++++++++++++++++++++++-------------
1 file changed, 25 insertions(+), 13 deletions(-)
diff --git a/drivers/irqchip/irq-gic.c b/drivers/irqchip/irq-gic.c
index 9ed278902d64..97b227cf3076 100644
--- a/drivers/irqchip/irq-gic.c
+++ b/drivers/irqchip/irq-gic.c
@@ -77,22 +77,25 @@ static DEFINE_RAW_SPINLOCK(irq_controller_lock);
/*
* This lock is used by the big.LITTLE migration code to ensure no IPIs
* can be pended on the old core after the map has been updated.
+ *
+ * This lock may be locked for reading from both IRQ and FIQ handlers
+ * and therefore must not be locked for writing when these are enabled.
*/
#ifdef CONFIG_BL_SWITCHER
-static DEFINE_RAW_SPINLOCK(cpu_map_migration_lock);
+static DEFINE_RWLOCK(cpu_map_migration_lock);
-static inline void gic_migration_lock(unsigned long *flags)
+static inline void gic_migration_lock(void)
{
- raw_spin_lock_irqsave(&cpu_map_migration_lock, *flags);
+ read_lock(&cpu_map_migration_lock);
}
-static inline void gic_migration_unlock(unsigned long flags)
+static inline void gic_migration_unlock(void)
{
- raw_spin_unlock_irqrestore(&cpu_map_migration_lock, flags);
+ read_unlock(&cpu_map_migration_lock);
}
#else
-static inline void gic_migration_lock(unsigned long *flags) {}
-static inline void gic_migration_unlock(unsigned long flags) {}
+static inline void gic_migration_lock(void) {}
+static inline void gic_migration_unlock(void) {}
#endif
/*
@@ -643,12 +646,20 @@ static void __init gic_pm_init(struct gic_chip_data *gic)
#endif
#ifdef CONFIG_SMP
+/*
+ * Raise the specified IPI on all cpus set in mask.
+ *
+ * This function is safe to call from all calling contexts, including
+ * FIQ handlers. It relies on gic_migration_lock() being multiply acquirable
+ * to avoid deadlocks when the function is re-entered at different
+ * exception levels.
+ */
static void gic_raise_softirq(const struct cpumask *mask, unsigned int irq)
{
int cpu;
- unsigned long flags, map = 0;
+ unsigned long map = 0;
- gic_migration_lock(&flags);
+ gic_migration_lock();
/* Convert our logical CPU mask into a physical one. */
for_each_cpu(cpu, mask)
@@ -663,7 +674,7 @@ static void gic_raise_softirq(const struct cpumask *mask, unsigned int irq)
/* this always happens on GIC0 */
writel_relaxed(map << 16 | irq, gic_data_dist_base(&gic_data[0]) + GIC_DIST_SOFTINT);
- gic_migration_unlock(flags);
+ gic_migration_unlock();
}
#endif
@@ -711,7 +722,8 @@ int gic_get_cpu_id(unsigned int cpu)
* Migrate all peripheral interrupts with a target matching the current CPU
* to the interface corresponding to @new_cpu_id. The CPU interface mapping
* is also updated. Targets to other CPU interfaces are unchanged.
- * This must be called with IRQs locally disabled.
+ * This must be called from a task context and with IRQ and FIQ locally
+ * disabled.
*/
void gic_migrate_target(unsigned int new_cpu_id)
{
@@ -742,9 +754,9 @@ void gic_migrate_target(unsigned int new_cpu_id)
* pending on the old cpu static. That means we can defer the
* migration until after we have released the irq_controller_lock.
*/
- raw_spin_lock(&cpu_map_migration_lock);
+ write_lock(&cpu_map_migration_lock);
gic_cpu_map[cpu] = 1 << new_cpu_id;
- raw_spin_unlock(&cpu_map_migration_lock);
+ write_unlock(&cpu_map_migration_lock);
/*
* Find all the peripheral interrupts targetting the current
--
2.4.3
Currently it is not possible to exploit FIQ for systems with a GIC, even
on systems are otherwise capable of it. This patch makes it possible
for IPIs to be delivered using FIQ.
To do so it modifies the register state so that normal interrupts are
placed in group 1 and specific IPIs are placed into group 0. It also
configures the controller to raise group 0 interrupts using the FIQ
signal. Finally it provides a means for architecture code to define
which IPIs shall use FIQ and to acknowledge any IPIs that are raised.
All GIC hardware except GICv1-without-TrustZone support provides a means
to group exceptions into group 0 and group 1 but the hardware
functionality is unavailable to the kernel when a secure monitor is
present because access to the grouping registers are prohibited outside
"secure world". However when grouping is not available (or in the case
of early GICv1 implementations is very hard to configure) the code to
change groups does not deploy and all IPIs will be raised via IRQ.
Signed-off-by: Daniel Thompson <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: Jason Cooper <[email protected]>
Cc: Russell King <[email protected]>
Cc: Marc Zyngier <[email protected]>
Tested-by: Jon Medhurst <[email protected]>
---
arch/arm/kernel/traps.c | 9 ++-
drivers/irqchip/irq-gic.c | 168 +++++++++++++++++++++++++++++++++++++---
include/linux/irqchip/arm-gic.h | 6 ++
3 files changed, 171 insertions(+), 12 deletions(-)
diff --git a/arch/arm/kernel/traps.c b/arch/arm/kernel/traps.c
index d358226236f2..5634823a39cf 100644
--- a/arch/arm/kernel/traps.c
+++ b/arch/arm/kernel/traps.c
@@ -479,7 +479,14 @@ asmlinkage void __exception_irq_entry handle_fiq_as_nmi(struct pt_regs *regs)
nmi_enter();
- /* nop. FIQ handlers for special arch/arm features can be added here. */
+ /*
+ * Either the interrupt controller supports FIQ, meaning it will
+ * do the right thing with this call, or we will end up treating a
+ * spurious FIQ (which is normally fatal) as though it were an IRQ
+ * which, although it risks deadlock, still gives us a sporting
+ * chance of surviving long enough to log errors.
+ */
+ handle_arch_irq(regs);
nmi_exit();
diff --git a/drivers/irqchip/irq-gic.c b/drivers/irqchip/irq-gic.c
index 97b227cf3076..77d14beb0cc8 100644
--- a/drivers/irqchip/irq-gic.c
+++ b/drivers/irqchip/irq-gic.c
@@ -41,6 +41,7 @@
#include <linux/irqchip/chained_irq.h>
#include <linux/irqchip/arm-gic.h>
#include <linux/irqchip/arm-gic-acpi.h>
+#include <linux/ratelimit.h>
#include <asm/cputype.h>
#include <asm/irq.h>
@@ -50,6 +51,10 @@
#include "irq-gic-common.h"
#include "irqchip.h"
+#ifndef SMP_IPI_FIQ_MASK
+#define SMP_IPI_FIQ_MASK 0
+#endif
+
union gic_base {
void __iomem *common_base;
void __percpu * __iomem *percpu_base;
@@ -67,6 +72,7 @@ struct gic_chip_data {
#endif
struct irq_domain *domain;
unsigned int gic_irqs;
+ bool sgi_with_nsatt;
#ifdef CONFIG_GIC_NON_BANKED
void __iomem *(*get_base)(union gic_base *);
#endif
@@ -285,12 +291,39 @@ static int gic_set_affinity(struct irq_data *d, const struct cpumask *mask_val,
}
#endif
+/*
+ * Fully acknowledge (both ack and eoi) any outstanding FIQ-based IPI,
+ * otherwise do nothing.
+ */
+void gic_handle_fiq(struct pt_regs *regs)
+{
+ struct gic_chip_data *gic = &gic_data[0];
+ void __iomem *cpu_base = gic_data_cpu_base(gic);
+ unsigned long irqstat, irqnr;
+
+ while ((1u << readl_relaxed(cpu_base + GIC_CPU_HIGHPRI)) &
+ SMP_IPI_FIQ_MASK) {
+ irqstat = readl_relaxed(cpu_base + GIC_CPU_INTACK);
+ writel_relaxed(irqstat, cpu_base + GIC_CPU_EOI);
+
+ irqnr = irqstat & GICC_IAR_INT_ID_MASK;
+ WARN_RATELIMIT(irqnr > 16,
+ "Unexpected irqnr %lu (bad prioritization?)\n",
+ irqnr);
+ }
+}
+
static void __exception_irq_entry gic_handle_irq(struct pt_regs *regs)
{
u32 irqstat, irqnr;
struct gic_chip_data *gic = &gic_data[0];
void __iomem *cpu_base = gic_data_cpu_base(gic);
+ if (in_nmi()) {
+ gic_handle_fiq(regs);
+ return;
+ }
+
do {
irqstat = readl_relaxed(cpu_base + GIC_CPU_INTACK);
irqnr = irqstat & GICC_IAR_INT_ID_MASK;
@@ -351,6 +384,55 @@ static struct irq_chip gic_chip = {
.flags = IRQCHIP_SET_TYPE_MASKED,
};
+/*
+ * Shift an interrupt between Group 0 and Group 1.
+ *
+ * In addition to changing the group we also modify the priority to
+ * match what "ARM strongly recommends" for a system where no Group 1
+ * interrupt must ever preempt a Group 0 interrupt.
+ *
+ * If is safe to call this function on systems which do not support
+ * grouping (it will have no effect).
+ */
+static void gic_set_group_irq(struct gic_chip_data *gic, unsigned int hwirq,
+ int group)
+{
+ void __iomem *base = gic_data_dist_base(gic);
+ unsigned int grp_reg = hwirq / 32 * 4;
+ u32 grp_mask = BIT(hwirq % 32);
+ u32 grp_val;
+
+ unsigned int pri_reg = (hwirq / 4) * 4;
+ u32 pri_mask = BIT(7 + ((hwirq % 4) * 8));
+ u32 pri_val;
+
+ /*
+ * Systems which do not support grouping will have not have
+ * the EnableGrp1 bit set.
+ */
+ if (!(GICD_ENABLE_GRP1 & readl_relaxed(base + GIC_DIST_CTRL)))
+ return;
+
+ raw_spin_lock(&irq_controller_lock);
+
+ grp_val = readl_relaxed(base + GIC_DIST_IGROUP + grp_reg);
+ pri_val = readl_relaxed(base + GIC_DIST_PRI + pri_reg);
+
+ if (group) {
+ grp_val |= grp_mask;
+ pri_val |= pri_mask;
+ } else {
+ grp_val &= ~grp_mask;
+ pri_val &= ~pri_mask;
+ }
+
+ writel_relaxed(grp_val, base + GIC_DIST_IGROUP + grp_reg);
+ writel_relaxed(pri_val, base + GIC_DIST_PRI + pri_reg);
+
+ raw_spin_unlock(&irq_controller_lock);
+}
+
+
void __init gic_cascade_irq(unsigned int gic_nr, unsigned int irq)
{
if (gic_nr >= MAX_GIC_NR)
@@ -382,15 +464,24 @@ static u8 gic_get_cpumask(struct gic_chip_data *gic)
static void gic_cpu_if_up(void)
{
void __iomem *cpu_base = gic_data_cpu_base(&gic_data[0]);
- u32 bypass = 0;
+ void __iomem *dist_base = gic_data_dist_base(&gic_data[0]);
+ u32 ctrl = 0;
/*
- * Preserve bypass disable bits to be written back later
- */
- bypass = readl(cpu_base + GIC_CPU_CTRL);
- bypass &= GICC_DIS_BYPASS_MASK;
+ * Preserve bypass disable bits to be written back later
+ */
+ ctrl = readl(cpu_base + GIC_CPU_CTRL);
+ ctrl &= GICC_DIS_BYPASS_MASK;
+
+ /*
+ * If EnableGrp1 is set in the distributor then enable group 1
+ * support for this CPU (and route group 0 interrupts to FIQ).
+ */
+ if (GICD_ENABLE_GRP1 & readl_relaxed(dist_base + GIC_DIST_CTRL))
+ ctrl |= GICC_COMMON_BPR | GICC_FIQ_EN | GICC_ACK_CTL |
+ GICC_ENABLE_GRP1;
- writel_relaxed(bypass | GICC_ENABLE, cpu_base + GIC_CPU_CTRL);
+ writel_relaxed(ctrl | GICC_ENABLE, cpu_base + GIC_CPU_CTRL);
}
@@ -414,7 +505,34 @@ static void __init gic_dist_init(struct gic_chip_data *gic)
gic_dist_config(base, gic_irqs, NULL);
- writel_relaxed(GICD_ENABLE, base + GIC_DIST_CTRL);
+ /*
+ * Set EnableGrp1/EnableGrp0 (bit 1 and 0) or EnableGrp (bit 0 only,
+ * bit 1 ignored) depending on current mode.
+ */
+ writel_relaxed(GICD_ENABLE_GRP1 | GICD_ENABLE, base + GIC_DIST_CTRL);
+
+ /*
+ * Some GICv1 devices (even those with security extensions) do not
+ * implement EnableGrp1 meaning some parts of the above write might
+ * be ignored. We will only enable FIQ support if the bit can be set.
+ */
+ if (GICD_ENABLE_GRP1 & readl_relaxed(base + GIC_DIST_CTRL)) {
+ /*
+ * Set all global interrupts to be group 1 (signalled with
+ * IRQ).
+ */
+ for (i = 32; i < gic_irqs; i += 32)
+ writel_relaxed(0xffffffff,
+ base + GIC_DIST_IGROUP + i * 4 / 32);
+
+ /*
+ * If the GIC supports the security extension then SGIs
+ * will be filtered based on the value of NSATT. If the
+ * GIC has this support then enable NSATT support.
+ */
+ if (GICD_SECURITY_EXTN & readl_relaxed(base + GIC_DIST_CTR))
+ gic->sgi_with_nsatt = true;
+ }
}
static void gic_cpu_init(struct gic_chip_data *gic)
@@ -423,6 +541,7 @@ static void gic_cpu_init(struct gic_chip_data *gic)
void __iomem *base = gic_data_cpu_base(gic);
unsigned int cpu_mask, cpu = smp_processor_id();
int i;
+ unsigned long ipi_fiq_mask, fiq;
/*
* Get what the GIC says our CPU mask is.
@@ -441,6 +560,23 @@ static void gic_cpu_init(struct gic_chip_data *gic)
gic_cpu_config(dist_base, NULL);
+ /*
+ * If the distributor is configured to support interrupt grouping
+ * then set any PPI and SGI interrupts not set in SMP_IPI_FIQ_MASK
+ * to be group1 and ensure any remaining group 0 interrupts have
+ * the right priority.
+ *
+ * Note that IGROUP[0] is banked, meaning that although we are
+ * writing to a distributor register we are actually performing
+ * part of the per-cpu initialization.
+ */
+ if (GICD_ENABLE_GRP1 & readl_relaxed(dist_base + GIC_DIST_CTRL)) {
+ ipi_fiq_mask = SMP_IPI_FIQ_MASK;
+ writel_relaxed(~ipi_fiq_mask, dist_base + GIC_DIST_IGROUP + 0);
+ for_each_set_bit(fiq, &ipi_fiq_mask, 16)
+ gic_set_group_irq(gic, fiq, 0);
+ }
+
writel_relaxed(GICC_INT_PRI_THRESHOLD, base + GIC_CPU_PRIMASK);
gic_cpu_if_up();
}
@@ -451,7 +587,8 @@ void gic_cpu_if_down(void)
u32 val = 0;
val = readl(cpu_base + GIC_CPU_CTRL);
- val &= ~GICC_ENABLE;
+ val &= ~(GICC_COMMON_BPR | GICC_FIQ_EN | GICC_ACK_CTL |
+ GICC_ENABLE_GRP1 | GICC_ENABLE);
writel_relaxed(val, cpu_base + GIC_CPU_CTRL);
}
@@ -530,7 +667,8 @@ static void gic_dist_restore(unsigned int gic_nr)
writel_relaxed(gic_data[gic_nr].saved_spi_enable[i],
dist_base + GIC_DIST_ENABLE_SET + i * 4);
- writel_relaxed(GICD_ENABLE, dist_base + GIC_DIST_CTRL);
+ writel_relaxed(GICD_ENABLE_GRP1 | GICD_ENABLE,
+ dist_base + GIC_DIST_CTRL);
}
static void gic_cpu_save(unsigned int gic_nr)
@@ -658,6 +796,8 @@ static void gic_raise_softirq(const struct cpumask *mask, unsigned int irq)
{
int cpu;
unsigned long map = 0;
+ unsigned long softint;
+ void __iomem *dist_base;
gic_migration_lock();
@@ -665,14 +805,20 @@ static void gic_raise_softirq(const struct cpumask *mask, unsigned int irq)
for_each_cpu(cpu, mask)
map |= gic_cpu_map[cpu];
+ /* This always happens on GIC0 */
+ dist_base = gic_data_dist_base(&gic_data[0]);
+
/*
* Ensure that stores to Normal memory are visible to the
* other CPUs before they observe us issuing the IPI.
*/
dmb(ishst);
- /* this always happens on GIC0 */
- writel_relaxed(map << 16 | irq, gic_data_dist_base(&gic_data[0]) + GIC_DIST_SOFTINT);
+ softint = map << 16 | irq;
+
+ writel_relaxed(softint, dist_base + GIC_DIST_SOFTINT);
+ if (gic_data[0].sgi_with_nsatt)
+ writel_relaxed(softint | 0x8000, dist_base + GIC_DIST_SOFTINT);
gic_migration_unlock();
}
diff --git a/include/linux/irqchip/arm-gic.h b/include/linux/irqchip/arm-gic.h
index 9de976b4f9a7..249554388142 100644
--- a/include/linux/irqchip/arm-gic.h
+++ b/include/linux/irqchip/arm-gic.h
@@ -22,6 +22,10 @@
#define GIC_CPU_IDENT 0xfc
#define GICC_ENABLE 0x1
+#define GICC_ENABLE_GRP1 0x2
+#define GICC_ACK_CTL 0x4
+#define GICC_FIQ_EN 0x8
+#define GICC_COMMON_BPR 0x10
#define GICC_INT_PRI_THRESHOLD 0xf0
#define GICC_IAR_INT_ID_MASK 0x3ff
#define GICC_INT_SPURIOUS 1023
@@ -44,7 +48,9 @@
#define GIC_DIST_SGI_PENDING_SET 0xf20
#define GICD_ENABLE 0x1
+#define GICD_ENABLE_GRP1 0x2
#define GICD_DISABLE 0x0
+#define GICD_SECURITY_EXTN 0x400
#define GICD_INT_ACTLOW_LVLTRIG 0x0
#define GICD_INT_EN_CLR_X32 0xffffffff
#define GICD_INT_EN_SET_SGI 0x0000ffff
--
2.4.3
Currently there is a quite a pile of code sitting in
arch/x86/kernel/apic/hw_nmi.c to support safe all-cpu backtracing from NMI.
The code is inaccessible to backtrace implementations for other
architectures, which is a shame because they would probably like to be
safe too.
Copy this code into printk, reworking it a little as we do so to make
it easier to exploit as library code.
We'll port the x86 NMI backtrace logic to it in a later patch.
Signed-off-by: Daniel Thompson <[email protected]>
Cc: Steven Rostedt <[email protected]>
---
include/linux/printk.h | 20 ++++++
init/Kconfig | 3 +
kernel/printk/Makefile | 1 +
kernel/printk/nmi_backtrace.c | 147 ++++++++++++++++++++++++++++++++++++++++++
4 files changed, 171 insertions(+)
create mode 100644 kernel/printk/nmi_backtrace.c
diff --git a/include/linux/printk.h b/include/linux/printk.h
index 58b1fec40d37..07da23b10f57 100644
--- a/include/linux/printk.h
+++ b/include/linux/printk.h
@@ -230,6 +230,26 @@ static inline void show_regs_print_info(const char *log_lvl)
}
#endif
+#ifdef CONFIG_PRINTK_NMI_BACKTRACE
+/*
+ * printk_nmi_backtrace_prepare/complete are called to prepare the
+ * system for some or all cores to issue trace from NMI.
+ * printk_nmi_backtrace_complete will print buffered output and cannot
+ * (safely) be called from NMI.
+ */
+extern int printk_nmi_backtrace_prepare(void);
+extern void printk_nmi_backtrace_complete(void);
+
+/*
+ * printk_nmi_backtrace_this_cpu_begin/end are used divert/restore printk
+ * on this cpu. The result is the output of printk() (by this CPU) will be
+ * stored in temporary buffers for later printing by
+ * printk_nmi_backtrace_complete.
+ */
+extern void printk_nmi_backtrace_this_cpu_begin(void);
+extern void printk_nmi_backtrace_this_cpu_end(void);
+#endif
+
extern asmlinkage void dump_stack(void) __cold;
#ifndef pr_fmt
diff --git a/init/Kconfig b/init/Kconfig
index af09b4fb43d2..132e4f05253e 100644
--- a/init/Kconfig
+++ b/init/Kconfig
@@ -1439,6 +1439,9 @@ config PRINTK
very difficult to diagnose system problems, saying N here is
strongly discouraged.
+config PRINTK_NMI_BACKTRACE
+ bool
+
config BUG
bool "BUG() support" if EXPERT
default y
diff --git a/kernel/printk/Makefile b/kernel/printk/Makefile
index 85405bdcf2b3..1849b001384a 100644
--- a/kernel/printk/Makefile
+++ b/kernel/printk/Makefile
@@ -1,2 +1,3 @@
obj-y = printk.o
+obj-$(CONFIG_PRINTK_NMI_BACKTRACE) += nmi_backtrace.o
obj-$(CONFIG_A11Y_BRAILLE_CONSOLE) += braille.o
diff --git a/kernel/printk/nmi_backtrace.c b/kernel/printk/nmi_backtrace.c
new file mode 100644
index 000000000000..f24761262756
--- /dev/null
+++ b/kernel/printk/nmi_backtrace.c
@@ -0,0 +1,147 @@
+#include <linux/kernel.h>
+#include <linux/seq_buf.h>
+
+#define NMI_BUF_SIZE 4096
+
+struct nmi_seq_buf {
+ unsigned char buffer[NMI_BUF_SIZE];
+ struct seq_buf seq;
+};
+
+/* Safe printing in NMI context */
+static DEFINE_PER_CPU(struct nmi_seq_buf, nmi_print_seq);
+
+static DEFINE_PER_CPU(printk_func_t, nmi_print_saved_print_func);
+
+/* "in progress" flag of NMI printing */
+static unsigned long nmi_print_flag;
+
+static int __init printk_nmi_backtrace_init(void)
+{
+ struct nmi_seq_buf *s;
+ int cpu;
+
+ for_each_possible_cpu(cpu) {
+ s = &per_cpu(nmi_print_seq, cpu);
+ seq_buf_init(&s->seq, s->buffer, NMI_BUF_SIZE);
+ }
+
+ return 0;
+}
+pure_initcall(printk_nmi_backtrace_init);
+
+/*
+ * It is not safe to call printk() directly from NMI handlers.
+ * It may be fine if the NMI detected a lock up and we have no choice
+ * but to do so, but doing a NMI on all other CPUs to get a back trace
+ * can be done with a sysrq-l. We don't want that to lock up, which
+ * can happen if the NMI interrupts a printk in progress.
+ *
+ * Instead, we redirect the vprintk() to this nmi_vprintk() that writes
+ * the content into a per cpu seq_buf buffer. Then when the NMIs are
+ * all done, we can safely dump the contents of the seq_buf to a printk()
+ * from a non NMI context.
+ *
+ * This is not a generic printk() implementation and must be used with
+ * great care. In particular there is a static limit on the quantity of
+ * data that may be emitted during NMI, only one client can be active at
+ * one time (arbitrated by the return value of printk_nmi_begin() and
+ * it is required that something at task or interrupt context be scheduled
+ * to issue the output.
+ */
+static int nmi_vprintk(const char *fmt, va_list args)
+{
+ struct nmi_seq_buf *s = this_cpu_ptr(&nmi_print_seq);
+ unsigned int len = seq_buf_used(&s->seq);
+
+ seq_buf_vprintf(&s->seq, fmt, args);
+ return seq_buf_used(&s->seq) - len;
+}
+
+/*
+ * Reserve the NMI printk mechanism. Return an error if some other component
+ * is already using it.
+ */
+int printk_nmi_backtrace_prepare(void)
+{
+ if (test_and_set_bit(0, &nmi_print_flag)) {
+ /*
+ * If something is already using the NMI print facility we
+ * can't allow a second one...
+ */
+ return -EBUSY;
+ }
+
+ return 0;
+}
+
+static void print_seq_line(struct nmi_seq_buf *s, int start, int end)
+{
+ const char *buf = s->buffer + start;
+
+ printk("%.*s", (end - start) + 1, buf);
+}
+
+void printk_nmi_backtrace_complete(void)
+{
+ struct nmi_seq_buf *s;
+ int len, cpu, i, last_i;
+
+ /*
+ * Now that all the NMIs have triggered, we can dump out their
+ * back traces safely to the console.
+ */
+ for_each_possible_cpu(cpu) {
+ s = &per_cpu(nmi_print_seq, cpu);
+ last_i = 0;
+
+ len = seq_buf_used(&s->seq);
+ if (!len)
+ continue;
+
+ /* Print line by line. */
+ for (i = 0; i < len; i++) {
+ if (s->buffer[i] == '\n') {
+ print_seq_line(s, last_i, i);
+ last_i = i + 1;
+ }
+ }
+ /* Check if there was a partial line. */
+ if (last_i < len) {
+ print_seq_line(s, last_i, len - 1);
+ pr_cont("\n");
+ }
+
+ /* Wipe out the buffer ready for the next time around. */
+ seq_buf_clear(&s->seq);
+ }
+
+ clear_bit(0, &nmi_print_flag);
+}
+
+void printk_nmi_backtrace_this_cpu_begin(void)
+{
+ /*
+ * Detect double-begins and report them. This code is unsafe (because
+ * it will print from NMI) but things are pretty badly damaged if the
+ * NMI re-enters and is somehow granted permission to use NMI printk,
+ * so how much worse can it get? Also since this code interferes with
+ * the operation of printk it is unlikely that any consequential
+ * failures will be able to log anything making this our last
+ * opportunity to tell anyone that something is wrong.
+ */
+ if (this_cpu_read(nmi_print_saved_print_func)) {
+ this_cpu_write(printk_func,
+ this_cpu_read(nmi_print_saved_print_func));
+ BUG();
+ }
+
+ this_cpu_write(nmi_print_saved_print_func, this_cpu_read(printk_func));
+ this_cpu_write(printk_func, nmi_vprintk);
+}
+
+void printk_nmi_backtrace_this_cpu_end(void)
+{
+ this_cpu_write(printk_func, this_cpu_read(nmi_print_saved_print_func));
+ this_cpu_write(nmi_print_saved_print_func, NULL);
+}
--
2.4.3
Much of the code sitting in arch/x86/kernel/apic/hw_nmi.c to support safe
all-cpu backtracing from NMI has been copied to printk.c to make it
accessible to other architectures.
Port the x86 NMI backtrace to the generic code.
Signed-off-by: Daniel Thompson <[email protected]>
Cc: Steven Rostedt <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Acked-by: Ingo Molnar <[email protected]>
Cc: "H. Peter Anvin" <[email protected]>
Cc: [email protected]
---
arch/x86/Kconfig | 1 +
arch/x86/kernel/apic/hw_nmi.c | 104 ++++--------------------------------------
2 files changed, 10 insertions(+), 95 deletions(-)
diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig
index 55bced17dc95..efc3510a3930 100644
--- a/arch/x86/Kconfig
+++ b/arch/x86/Kconfig
@@ -149,6 +149,7 @@ config X86
select VIRT_TO_BUS
select X86_DEV_DMA_OPS if X86_64
select X86_FEATURE_NAMES if PROC_FS
+ select PRINTK_NMI_BACKTRACE if X86_LOCAL_APIC
config INSTRUCTION_DECODER
def_bool y
diff --git a/arch/x86/kernel/apic/hw_nmi.c b/arch/x86/kernel/apic/hw_nmi.c
index 6873ab925d00..7a682beac3a0 100644
--- a/arch/x86/kernel/apic/hw_nmi.c
+++ b/arch/x86/kernel/apic/hw_nmi.c
@@ -30,40 +30,17 @@ u64 hw_nmi_get_sample_period(int watchdog_thresh)
#ifdef arch_trigger_all_cpu_backtrace
/* For reliability, we're prepared to waste bits here. */
static DECLARE_BITMAP(backtrace_mask, NR_CPUS) __read_mostly;
-static cpumask_t printtrace_mask;
-
-#define NMI_BUF_SIZE 4096
-
-struct nmi_seq_buf {
- unsigned char buffer[NMI_BUF_SIZE];
- struct seq_buf seq;
-};
-
-/* Safe printing in NMI context */
-static DEFINE_PER_CPU(struct nmi_seq_buf, nmi_print_seq);
-
-/* "in progress" flag of arch_trigger_all_cpu_backtrace */
-static unsigned long backtrace_flag;
-
-static void print_seq_line(struct nmi_seq_buf *s, int start, int end)
-{
- const char *buf = s->buffer + start;
-
- printk("%.*s", (end - start) + 1, buf);
-}
void arch_trigger_all_cpu_backtrace(bool include_self)
{
- struct nmi_seq_buf *s;
- int len;
- int cpu;
- int i;
+ int err, i;
int this_cpu = get_cpu();
- if (test_and_set_bit(0, &backtrace_flag)) {
+ err = printk_nmi_backtrace_prepare();
+ if (err) {
/*
- * If there is already a trigger_all_cpu_backtrace() in progress
- * (backtrace_flag == 1), don't output double cpu dump infos.
+ * If there is already an nmi printk sequence in
+ * progress then just give up...
*/
put_cpu();
return;
@@ -73,16 +50,6 @@ void arch_trigger_all_cpu_backtrace(bool include_self)
if (!include_self)
cpumask_clear_cpu(this_cpu, to_cpumask(backtrace_mask));
- cpumask_copy(&printtrace_mask, to_cpumask(backtrace_mask));
- /*
- * Set up per_cpu seq_buf buffers that the NMIs running on the other
- * CPUs will write to.
- */
- for_each_cpu(cpu, to_cpumask(backtrace_mask)) {
- s = &per_cpu(nmi_print_seq, cpu);
- seq_buf_init(&s->seq, s->buffer, NMI_BUF_SIZE);
- }
-
if (!cpumask_empty(to_cpumask(backtrace_mask))) {
pr_info("sending NMI to %s CPUs:\n",
(include_self ? "all" : "other"));
@@ -97,73 +64,20 @@ void arch_trigger_all_cpu_backtrace(bool include_self)
touch_softlockup_watchdog();
}
- /*
- * Now that all the NMIs have triggered, we can dump out their
- * back traces safely to the console.
- */
- for_each_cpu(cpu, &printtrace_mask) {
- int last_i = 0;
-
- s = &per_cpu(nmi_print_seq, cpu);
- len = seq_buf_used(&s->seq);
- if (!len)
- continue;
-
- /* Print line by line. */
- for (i = 0; i < len; i++) {
- if (s->buffer[i] == '\n') {
- print_seq_line(s, last_i, i);
- last_i = i + 1;
- }
- }
- /* Check if there was a partial line. */
- if (last_i < len) {
- print_seq_line(s, last_i, len - 1);
- pr_cont("\n");
- }
- }
-
- clear_bit(0, &backtrace_flag);
- smp_mb__after_atomic();
+ printk_nmi_backtrace_complete();
put_cpu();
}
-/*
- * It is not safe to call printk() directly from NMI handlers.
- * It may be fine if the NMI detected a lock up and we have no choice
- * but to do so, but doing a NMI on all other CPUs to get a back trace
- * can be done with a sysrq-l. We don't want that to lock up, which
- * can happen if the NMI interrupts a printk in progress.
- *
- * Instead, we redirect the vprintk() to this nmi_vprintk() that writes
- * the content into a per cpu seq_buf buffer. Then when the NMIs are
- * all done, we can safely dump the contents of the seq_buf to a printk()
- * from a non NMI context.
- */
-static int nmi_vprintk(const char *fmt, va_list args)
-{
- struct nmi_seq_buf *s = this_cpu_ptr(&nmi_print_seq);
- unsigned int len = seq_buf_used(&s->seq);
-
- seq_buf_vprintf(&s->seq, fmt, args);
- return seq_buf_used(&s->seq) - len;
-}
-
static int
arch_trigger_all_cpu_backtrace_handler(unsigned int cmd, struct pt_regs *regs)
{
- int cpu;
-
- cpu = smp_processor_id();
+ int cpu = smp_processor_id();
if (cpumask_test_cpu(cpu, to_cpumask(backtrace_mask))) {
- printk_func_t printk_func_save = this_cpu_read(printk_func);
-
- /* Replace printk to write into the NMI seq */
- this_cpu_write(printk_func, nmi_vprintk);
+ printk_nmi_backtrace_this_cpu_begin();
printk(KERN_WARNING "NMI backtrace for cpu %d\n", cpu);
show_regs(regs);
- this_cpu_write(printk_func, printk_func_save);
+ printk_nmi_backtrace_this_cpu_end();
cpumask_clear_cpu(cpu, to_cpumask(backtrace_mask));
return NMI_HANDLED;
--
2.4.3
Replicate the x86 code to trigger a backtrace using an NMI and hook
it up to IPI on ARM.
The code differs slightly from the code on x86 because, on ARM, we do
now know at compile time whether a platform is capable of supporting FIQ.
We must avoid using an IPI to request a backtrace from the CPU on which
the backtrace was requested if interrupts are disabled and fall back to
generating it directly.
In addition the implementation of arch_trigger_all_cpu_backtrace() the
patch also includes a few small items of plumbing that must be hooked
up for the new code to work.
Credit:
Russell King provided the initial prototype implementing this feature
for ARM. Today the patch has been reworked and, mostly, rewriten to
keep it aligned with x86. However this patch does still include some
code from Russell's original prototype.
Signed-off-by: Daniel Thompson <[email protected]>
Cc: Russell King <[email protected]>
Cc: Steven Rostedt <[email protected]>
---
arch/arm/Kconfig | 1 +
arch/arm/include/asm/hardirq.h | 2 +-
arch/arm/include/asm/irq.h | 5 +++
arch/arm/include/asm/smp.h | 3 ++
arch/arm/kernel/smp.c | 82 ++++++++++++++++++++++++++++++++++++++++++
arch/arm/kernel/traps.c | 4 +++
6 files changed, 96 insertions(+), 1 deletion(-)
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index a750c1425c3a..8bf16a7438b7 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -79,6 +79,7 @@ config ARM
select OLD_SIGACTION
select OLD_SIGSUSPEND3
select PERF_USE_VMALLOC
+ select PRINTK_NMI_BACKTRACE
select RTC_LIB
select SYS_SUPPORTS_APM_EMULATION
# Above selects are sorted alphabetically; please add new ones
diff --git a/arch/arm/include/asm/hardirq.h b/arch/arm/include/asm/hardirq.h
index fe3ea776dc34..5df33e30ae1b 100644
--- a/arch/arm/include/asm/hardirq.h
+++ b/arch/arm/include/asm/hardirq.h
@@ -5,7 +5,7 @@
#include <linux/threads.h>
#include <asm/irq.h>
-#define NR_IPI 8
+#define NR_IPI 9
typedef struct {
unsigned int __softirq_pending;
diff --git a/arch/arm/include/asm/irq.h b/arch/arm/include/asm/irq.h
index 53c15dec7af6..be1d07d59ee9 100644
--- a/arch/arm/include/asm/irq.h
+++ b/arch/arm/include/asm/irq.h
@@ -35,6 +35,11 @@ extern void (*handle_arch_irq)(struct pt_regs *);
extern void set_handle_irq(void (*handle_irq)(struct pt_regs *));
#endif
+#ifdef CONFIG_SMP
+extern void arch_trigger_all_cpu_backtrace(bool);
+#define arch_trigger_all_cpu_backtrace(x) arch_trigger_all_cpu_backtrace(x)
+#endif
+
#endif
#endif
diff --git a/arch/arm/include/asm/smp.h b/arch/arm/include/asm/smp.h
index 2f3ac1ba6fb4..652dde6a304c 100644
--- a/arch/arm/include/asm/smp.h
+++ b/arch/arm/include/asm/smp.h
@@ -18,6 +18,8 @@
# error "<asm/smp.h> included in non-SMP build"
#endif
+#define SMP_IPI_FIQ_MASK 0x0100
+
#define raw_smp_processor_id() (current_thread_info()->cpu)
struct seq_file;
@@ -80,6 +82,7 @@ extern void arch_send_call_function_single_ipi(int cpu);
extern void arch_send_call_function_ipi_mask(const struct cpumask *mask);
extern void arch_send_wakeup_ipi_mask(const struct cpumask *mask);
+extern void ipi_cpu_backtrace(struct pt_regs *regs);
extern int register_ipi_completion(struct completion *completion, int cpu);
struct smp_operations {
diff --git a/arch/arm/kernel/smp.c b/arch/arm/kernel/smp.c
index 90dfbedfbfb8..b28658989d73 100644
--- a/arch/arm/kernel/smp.c
+++ b/arch/arm/kernel/smp.c
@@ -26,6 +26,7 @@
#include <linux/completion.h>
#include <linux/cpufreq.h>
#include <linux/irq_work.h>
+#include <linux/seq_buf.h>
#include <linux/atomic.h>
#include <asm/smp.h>
@@ -72,6 +73,7 @@ enum ipi_msg_type {
IPI_CPU_STOP,
IPI_IRQ_WORK,
IPI_COMPLETION,
+ IPI_CPU_BACKTRACE,
};
static DECLARE_COMPLETION(cpu_running);
@@ -463,6 +465,7 @@ static const char *ipi_types[NR_IPI] __tracepoint_string = {
S(IPI_CPU_STOP, "CPU stop interrupts"),
S(IPI_IRQ_WORK, "IRQ work interrupts"),
S(IPI_COMPLETION, "completion interrupts"),
+ S(IPI_CPU_BACKTRACE, "backtrace interrupts"),
};
static void smp_cross_call(const struct cpumask *target, unsigned int ipinr)
@@ -577,6 +580,8 @@ void handle_IPI(int ipinr, struct pt_regs *regs)
unsigned int cpu = smp_processor_id();
struct pt_regs *old_regs = set_irq_regs(regs);
+ BUILD_BUG_ON(SMP_IPI_FIQ_MASK != BIT(IPI_CPU_BACKTRACE));
+
if ((unsigned)ipinr < NR_IPI) {
trace_ipi_entry(ipi_types[ipinr]);
__inc_irq_stat(cpu, ipi_irqs[ipinr]);
@@ -630,6 +635,12 @@ void handle_IPI(int ipinr, struct pt_regs *regs)
irq_exit();
break;
+ case IPI_CPU_BACKTRACE:
+ irq_enter();
+ ipi_cpu_backtrace(regs);
+ irq_exit();
+ break;
+
default:
pr_crit("CPU%u: Unknown IPI message 0x%x\n",
cpu, ipinr);
@@ -724,3 +735,74 @@ static int __init register_cpufreq_notifier(void)
core_initcall(register_cpufreq_notifier);
#endif
+
+/* For reliability, we're prepared to waste bits here. */
+static DECLARE_BITMAP(backtrace_mask, NR_CPUS) __read_mostly;
+
+void arch_trigger_all_cpu_backtrace(bool include_self)
+{
+ int err, i;
+ int this_cpu = get_cpu();
+
+ err = printk_nmi_backtrace_prepare();
+ if (err) {
+ /*
+ * If there is already an nmi printk sequence in
+ * progress then just give up...
+ */
+ put_cpu();
+ return;
+ }
+
+ cpumask_copy(to_cpumask(backtrace_mask), cpu_online_mask);
+
+ /*
+ * If irqs are disabled on the current processor and
+ * IPI_CPU_BACKTRACE is delivered using IRQ then we aren't be able to
+ * react to IPI_CPU_BACKTRACE until we leave this function. This
+ * would force us to get stuck and, eventually, timeout. We avoid
+ * the timeout (and the resulting failure to print useful information)
+ * by calling the backtrace logic directly whenever irqs are disabled.
+ */
+ if (include_self && irqs_disabled()) {
+ ipi_cpu_backtrace(in_interrupt() ? get_irq_regs() : NULL);
+ include_self = false;
+ }
+
+ if (!include_self)
+ cpumask_clear_cpu(this_cpu, to_cpumask(backtrace_mask));
+
+ if (!cpumask_empty(to_cpumask(backtrace_mask))) {
+ pr_info("Sending FIQ to %s CPUs:\n",
+ (include_self ? "all" : "other"));
+ smp_cross_call(to_cpumask(backtrace_mask), IPI_CPU_BACKTRACE);
+ }
+
+ /* Wait for up to 10 seconds for all CPUs to do the backtrace */
+ for (i = 0; i < 10 * 1000; i++) {
+ if (cpumask_empty(to_cpumask(backtrace_mask)))
+ break;
+ mdelay(1);
+ touch_softlockup_watchdog();
+ }
+
+ printk_nmi_backtrace_complete();
+ put_cpu();
+}
+
+void ipi_cpu_backtrace(struct pt_regs *regs)
+{
+ int cpu = smp_processor_id();
+
+ if (cpumask_test_cpu(cpu, to_cpumask(backtrace_mask))) {
+ printk_nmi_backtrace_this_cpu_begin();
+ pr_warn("FIQ backtrace for cpu %d\n", cpu);
+ if (regs != NULL)
+ show_regs(regs);
+ else
+ dump_stack();
+ printk_nmi_backtrace_this_cpu_end();
+
+ cpumask_clear_cpu(cpu, to_cpumask(backtrace_mask));
+ }
+}
diff --git a/arch/arm/kernel/traps.c b/arch/arm/kernel/traps.c
index 5634823a39cf..c5fe42f345a9 100644
--- a/arch/arm/kernel/traps.c
+++ b/arch/arm/kernel/traps.c
@@ -488,6 +488,10 @@ asmlinkage void __exception_irq_entry handle_fiq_as_nmi(struct pt_regs *regs)
*/
handle_arch_irq(regs);
+#ifdef CONFIG_SMP
+ ipi_cpu_backtrace(regs);
+#endif
+
nmi_exit();
set_irq_regs(old_regs);
--
2.4.3
> Currently it is not possible to exploit FIQ for systems with a GIC, even
> on systems are otherwise capable of it. This patch makes it possible
> for IPIs to be delivered using FIQ.
I wonder if gic_set_group_irq() can easily be married with mxc_set_irq_fiq().
The driver sound/soc/fsl/imx-pcm-fiq.c uses mxc_set_irq_fiq() to
connect an (assembly) FIQ handler with a hardware IRQ. However, the
underlying implementation of mxc_set_irq_fiq() is only supported for
TZIC and AVIC (see arch/arm/mach-imx/irq-common.c).
On my i.MX6, which doesn't have an AVIC/TZIC but a GIC I could use a
method to turn a normal IRQ into a FIQ :-)