There is a new compatible string for the SAM9X60 sdhci device. It involves
an update of the properties about the clocks stuff.
Signed-off-by: Ludovic Desroches <[email protected]>
---
Changes:
- v2: remove the extra example and fix node label
This patch conflicts with Nicolas' one: "dt-bindings: sdhci-of-at91: add
the microchip,sdcal-inverted property". Let me know which one has to be
rebased or you can handle it.
Ludovic
.../devicetree/bindings/mmc/sdhci-atmel.txt | 15 ++++++++++++---
1 file changed, 12 insertions(+), 3 deletions(-)
diff --git a/Documentation/devicetree/bindings/mmc/sdhci-atmel.txt b/Documentation/devicetree/bindings/mmc/sdhci-atmel.txt
index 1b662d7171a0..5d541ad4d4eb 100644
--- a/Documentation/devicetree/bindings/mmc/sdhci-atmel.txt
+++ b/Documentation/devicetree/bindings/mmc/sdhci-atmel.txt
@@ -5,17 +5,26 @@ Documentation/devicetree/bindings/mmc/mmc.txt and the properties used by the
sdhci-of-at91 driver.
Required properties:
-- compatible: Must be "atmel,sama5d2-sdhci".
+- compatible: Must be "atmel,sama5d2-sdhci" or "microchip,sam9x60-sdhci".
- clocks: Phandlers to the clocks.
-- clock-names: Must be "hclock", "multclk", "baseclk";
+- clock-names: Must be "hclock", "multclk", "baseclk" for
+ "atmel,sama5d2-sdhci".
+ Must be "hclock", "multclk" for "microchip,sam9x60-sdhci".
+
+Optional properties:
+- assigned-clocks: The same with "multclk".
+- assigned-clock-rates The rate of "multclk" in order to not rely on the
+ gck configuration set by previous components.
Example:
-sdmmc0: sdio-host@a0000000 {
+mmc0: sdio-host@a0000000 {
compatible = "atmel,sama5d2-sdhci";
reg = <0xa0000000 0x300>;
interrupts = <31 IRQ_TYPE_LEVEL_HIGH 0>;
clocks = <&sdmmc0_hclk>, <&sdmmc0_gclk>, <&main>;
clock-names = "hclock", "multclk", "baseclk";
+ assigned-clocks = <&sdmmc0_gclk>;
+ assigned-clock-rates = <480000000>;
};
--
2.23.0
In the SAM9x60 SoC, there are only two clocks instead of three for the
SDHCI device. The base clk is no longer provided, it is generated
internally from the mult clk.
The values of the base clk and mul in the capabilities registers may not
reflect the reality as the mult clk is a programmable clock which can take
several rates. As we can't trust those values, take them from the clock
tree and update the capabilities according to.
As we can have the same pitfall, in some cases, with the SAMA5D2 Soc,
stop relying on capabilities too.
Signed-off-by: Ludovic Desroches <[email protected]>
---
Changes:
- v2: write caps0
drivers/mmc/host/sdhci-of-at91.c | 105 +++++++++++++++++--------------
1 file changed, 58 insertions(+), 47 deletions(-)
diff --git a/drivers/mmc/host/sdhci-of-at91.c b/drivers/mmc/host/sdhci-of-at91.c
index e7d1920729fb..9a1ae16a5417 100644
--- a/drivers/mmc/host/sdhci-of-at91.c
+++ b/drivers/mmc/host/sdhci-of-at91.c
@@ -30,7 +30,14 @@
#define SDHCI_AT91_PRESET_COMMON_CONF 0x400 /* drv type B, programmable clock mode */
+struct sdhci_at91_soc_data {
+ const struct sdhci_pltfm_data *pdata;
+ bool baseclk_is_generated_internally;
+ unsigned int divider_for_baseclk;
+};
+
struct sdhci_at91_priv {
+ const struct sdhci_at91_soc_data *soc_data;
struct clk *hclock;
struct clk *gck;
struct clk *mainck;
@@ -130,12 +137,24 @@ static const struct sdhci_ops sdhci_at91_sama5d2_ops = {
.set_power = sdhci_at91_set_power,
};
-static const struct sdhci_pltfm_data soc_data_sama5d2 = {
+static const struct sdhci_pltfm_data sdhci_sama5d2_pdata = {
.ops = &sdhci_at91_sama5d2_ops,
};
+static const struct sdhci_at91_soc_data soc_data_sama5d2 = {
+ .pdata = &sdhci_sama5d2_pdata,
+ .baseclk_is_generated_internally = false,
+};
+
+static const struct sdhci_at91_soc_data soc_data_sam9x60 = {
+ .pdata = &sdhci_sama5d2_pdata,
+ .baseclk_is_generated_internally = true,
+ .divider_for_baseclk = 2,
+};
+
static const struct of_device_id sdhci_at91_dt_match[] = {
{ .compatible = "atmel,sama5d2-sdhci", .data = &soc_data_sama5d2 },
+ { .compatible = "microchip,sam9x60-sdhci", .data = &soc_data_sam9x60 },
{}
};
MODULE_DEVICE_TABLE(of, sdhci_at91_dt_match);
@@ -145,50 +164,37 @@ static int sdhci_at91_set_clks_presets(struct device *dev)
struct sdhci_host *host = dev_get_drvdata(dev);
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct sdhci_at91_priv *priv = sdhci_pltfm_priv(pltfm_host);
- int ret;
unsigned int caps0, caps1;
unsigned int clk_base, clk_mul;
- unsigned int gck_rate, real_gck_rate;
+ unsigned int gck_rate, clk_base_rate;
unsigned int preset_div;
- /*
- * The mult clock is provided by as a generated clock by the PMC
- * controller. In order to set the rate of gck, we have to get the
- * base clock rate and the clock mult from capabilities.
- */
clk_prepare_enable(priv->hclock);
caps0 = readl(host->ioaddr + SDHCI_CAPABILITIES);
caps1 = readl(host->ioaddr + SDHCI_CAPABILITIES_1);
- clk_base = (caps0 & SDHCI_CLOCK_V3_BASE_MASK) >> SDHCI_CLOCK_BASE_SHIFT;
- clk_mul = (caps1 & SDHCI_CLOCK_MUL_MASK) >> SDHCI_CLOCK_MUL_SHIFT;
- gck_rate = clk_base * 1000000 * (clk_mul + 1);
- ret = clk_set_rate(priv->gck, gck_rate);
- if (ret < 0) {
- dev_err(dev, "failed to set gck");
- clk_disable_unprepare(priv->hclock);
- return ret;
- }
- /*
- * We need to check if we have the requested rate for gck because in
- * some cases this rate could be not supported. If it happens, the rate
- * is the closest one gck can provide. We have to update the value
- * of clk mul.
- */
- real_gck_rate = clk_get_rate(priv->gck);
- if (real_gck_rate != gck_rate) {
- clk_mul = real_gck_rate / (clk_base * 1000000) - 1;
- caps1 &= (~SDHCI_CLOCK_MUL_MASK);
- caps1 |= ((clk_mul << SDHCI_CLOCK_MUL_SHIFT) &
- SDHCI_CLOCK_MUL_MASK);
- /* Set capabilities in r/w mode. */
- writel(SDMMC_CACR_KEY | SDMMC_CACR_CAPWREN,
- host->ioaddr + SDMMC_CACR);
- writel(caps1, host->ioaddr + SDHCI_CAPABILITIES_1);
- /* Set capabilities in ro mode. */
- writel(0, host->ioaddr + SDMMC_CACR);
- dev_info(dev, "update clk mul to %u as gck rate is %u Hz\n",
- clk_mul, real_gck_rate);
- }
+
+ gck_rate = clk_get_rate(priv->gck);
+ if (priv->soc_data->baseclk_is_generated_internally)
+ clk_base_rate = gck_rate / priv->soc_data->divider_for_baseclk;
+ else
+ clk_base_rate = clk_get_rate(priv->mainck);
+
+ clk_base = clk_base_rate / 1000000;
+ clk_mul = gck_rate / clk_base_rate - 1;
+
+ caps0 &= (~SDHCI_CLOCK_V3_BASE_MASK);
+ caps0 |= ((clk_base << SDHCI_CLOCK_BASE_SHIFT) & SDHCI_CLOCK_V3_BASE_MASK);
+ caps1 &= (~SDHCI_CLOCK_MUL_MASK);
+ caps1 |= ((clk_mul << SDHCI_CLOCK_MUL_SHIFT) & SDHCI_CLOCK_MUL_MASK);
+ /* Set capabilities in r/w mode. */
+ writel(SDMMC_CACR_KEY | SDMMC_CACR_CAPWREN, host->ioaddr + SDMMC_CACR);
+ writel(caps0, host->ioaddr + SDHCI_CAPABILITIES_1);
+ writel(caps1, host->ioaddr + SDHCI_CAPABILITIES_1);
+ /* Set capabilities in ro mode. */
+ writel(0, host->ioaddr + SDMMC_CACR);
+
+ dev_info(dev, "update clk mul to %u as gck rate is %u Hz and clk base is %u Hz\n",
+ clk_mul, gck_rate, clk_base_rate);
/*
* We have to set preset values because it depends on the clk_mul
@@ -196,19 +202,19 @@ static int sdhci_at91_set_clks_presets(struct device *dev)
* maximum sd clock value is 120 MHz instead of 208 MHz. For that
* reason, we need to use presets to support SDR104.
*/
- preset_div = DIV_ROUND_UP(real_gck_rate, 24000000) - 1;
+ preset_div = DIV_ROUND_UP(gck_rate, 24000000) - 1;
writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
host->ioaddr + SDHCI_PRESET_FOR_SDR12);
- preset_div = DIV_ROUND_UP(real_gck_rate, 50000000) - 1;
+ preset_div = DIV_ROUND_UP(gck_rate, 50000000) - 1;
writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
host->ioaddr + SDHCI_PRESET_FOR_SDR25);
- preset_div = DIV_ROUND_UP(real_gck_rate, 100000000) - 1;
+ preset_div = DIV_ROUND_UP(gck_rate, 100000000) - 1;
writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
host->ioaddr + SDHCI_PRESET_FOR_SDR50);
- preset_div = DIV_ROUND_UP(real_gck_rate, 120000000) - 1;
+ preset_div = DIV_ROUND_UP(gck_rate, 120000000) - 1;
writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
host->ioaddr + SDHCI_PRESET_FOR_SDR104);
- preset_div = DIV_ROUND_UP(real_gck_rate, 50000000) - 1;
+ preset_div = DIV_ROUND_UP(gck_rate, 50000000) - 1;
writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
host->ioaddr + SDHCI_PRESET_FOR_DDR50);
@@ -303,7 +309,7 @@ static const struct dev_pm_ops sdhci_at91_dev_pm_ops = {
static int sdhci_at91_probe(struct platform_device *pdev)
{
const struct of_device_id *match;
- const struct sdhci_pltfm_data *soc_data;
+ const struct sdhci_at91_soc_data *soc_data;
struct sdhci_host *host;
struct sdhci_pltfm_host *pltfm_host;
struct sdhci_at91_priv *priv;
@@ -314,17 +320,22 @@ static int sdhci_at91_probe(struct platform_device *pdev)
return -EINVAL;
soc_data = match->data;
- host = sdhci_pltfm_init(pdev, soc_data, sizeof(*priv));
+ host = sdhci_pltfm_init(pdev, soc_data->pdata, sizeof(*priv));
if (IS_ERR(host))
return PTR_ERR(host);
pltfm_host = sdhci_priv(host);
priv = sdhci_pltfm_priv(pltfm_host);
+ priv->soc_data = soc_data;
priv->mainck = devm_clk_get(&pdev->dev, "baseclk");
if (IS_ERR(priv->mainck)) {
- dev_err(&pdev->dev, "failed to get baseclk\n");
- return PTR_ERR(priv->mainck);
+ if (soc_data->baseclk_is_generated_internally) {
+ priv->mainck = NULL;
+ } else {
+ dev_err(&pdev->dev, "failed to get baseclk\n");
+ return PTR_ERR(priv->mainck);
+ }
}
priv->hclock = devm_clk_get(&pdev->dev, "hclock");
--
2.23.0
Set the frequency of the generated clock used by sdmmc devices in order
to not rely on the configuration done by previous components.
Signed-off-by: Ludovic Desroches <[email protected]>
---
Changes:
-v2: none
arch/arm/boot/dts/sama5d2.dtsi | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm/boot/dts/sama5d2.dtsi b/arch/arm/boot/dts/sama5d2.dtsi
index 565204816e34..7665263af907 100644
--- a/arch/arm/boot/dts/sama5d2.dtsi
+++ b/arch/arm/boot/dts/sama5d2.dtsi
@@ -300,6 +300,8 @@
interrupts = <31 IRQ_TYPE_LEVEL_HIGH 0>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 31>, <&pmc PMC_TYPE_GCK 31>, <&pmc PMC_TYPE_CORE PMC_MAIN>;
clock-names = "hclock", "multclk", "baseclk";
+ assigned-clocks = <&pmc PMC_TYPE_GCK 31>;
+ assigned-clock-rates = <480000000>;
status = "disabled";
};
@@ -309,6 +311,8 @@
interrupts = <32 IRQ_TYPE_LEVEL_HIGH 0>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 32>, <&pmc PMC_TYPE_GCK 32>, <&pmc PMC_TYPE_CORE PMC_MAIN>;
clock-names = "hclock", "multclk", "baseclk";
+ assigned-clocks = <&pmc PMC_TYPE_GCK 32>;
+ assigned-clock-rates = <480000000>;
status = "disabled";
};
--
2.23.0
On Fri, 11 Oct 2019 12:33:37 +0200, Ludovic Desroches wrote:
> There is a new compatible string for the SAM9X60 sdhci device. It involves
> an update of the properties about the clocks stuff.
>
> Signed-off-by: Ludovic Desroches <[email protected]>
> ---
>
> Changes:
> - v2: remove the extra example and fix node label
>
> This patch conflicts with Nicolas' one: "dt-bindings: sdhci-of-at91: add
> the microchip,sdcal-inverted property". Let me know which one has to be
> rebased or you can handle it.
>
> Ludovic
>
>
> .../devicetree/bindings/mmc/sdhci-atmel.txt | 15 ++++++++++++---
> 1 file changed, 12 insertions(+), 3 deletions(-)
>
Reviewed-by: Rob Herring <[email protected]>
On Fri, 11 Oct 2019 at 12:33, Ludovic Desroches
<[email protected]> wrote:
>
> There is a new compatible string for the SAM9X60 sdhci device. It involves
> an update of the properties about the clocks stuff.
>
> Signed-off-by: Ludovic Desroches <[email protected]>
This doesn't apply any more, can you please re-spin it?
Kind regards
Uffe
> ---
>
> Changes:
> - v2: remove the extra example and fix node label
>
> This patch conflicts with Nicolas' one: "dt-bindings: sdhci-of-at91: add
> the microchip,sdcal-inverted property". Let me know which one has to be
> rebased or you can handle it.
>
> Ludovic
>
>
> .../devicetree/bindings/mmc/sdhci-atmel.txt | 15 ++++++++++++---
> 1 file changed, 12 insertions(+), 3 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/mmc/sdhci-atmel.txt b/Documentation/devicetree/bindings/mmc/sdhci-atmel.txt
> index 1b662d7171a0..5d541ad4d4eb 100644
> --- a/Documentation/devicetree/bindings/mmc/sdhci-atmel.txt
> +++ b/Documentation/devicetree/bindings/mmc/sdhci-atmel.txt
> @@ -5,17 +5,26 @@ Documentation/devicetree/bindings/mmc/mmc.txt and the properties used by the
> sdhci-of-at91 driver.
>
> Required properties:
> -- compatible: Must be "atmel,sama5d2-sdhci".
> +- compatible: Must be "atmel,sama5d2-sdhci" or "microchip,sam9x60-sdhci".
> - clocks: Phandlers to the clocks.
> -- clock-names: Must be "hclock", "multclk", "baseclk";
> +- clock-names: Must be "hclock", "multclk", "baseclk" for
> + "atmel,sama5d2-sdhci".
> + Must be "hclock", "multclk" for "microchip,sam9x60-sdhci".
> +
> +Optional properties:
> +- assigned-clocks: The same with "multclk".
> +- assigned-clock-rates The rate of "multclk" in order to not rely on the
> + gck configuration set by previous components.
>
>
> Example:
>
> -sdmmc0: sdio-host@a0000000 {
> +mmc0: sdio-host@a0000000 {
> compatible = "atmel,sama5d2-sdhci";
> reg = <0xa0000000 0x300>;
> interrupts = <31 IRQ_TYPE_LEVEL_HIGH 0>;
> clocks = <&sdmmc0_hclk>, <&sdmmc0_gclk>, <&main>;
> clock-names = "hclock", "multclk", "baseclk";
> + assigned-clocks = <&sdmmc0_gclk>;
> + assigned-clock-rates = <480000000>;
> };
> --
> 2.23.0
>
On Fri, Oct 18, 2019 at 12:56:14PM +0200, Ulf Hansson wrote:
> On Fri, 11 Oct 2019 at 12:33, Ludovic Desroches
> <[email protected]> wrote:
> >
> > There is a new compatible string for the SAM9X60 sdhci device. It involves
> > an update of the properties about the clocks stuff.
> >
> > Signed-off-by: Ludovic Desroches <[email protected]>
>
> This doesn't apply any more, can you please re-spin it?
Sure, I'll rebase these patches and send a v2
Regards
Ludovic
>
> Kind regards
> Uffe
>
>
> > ---
> >
> > Changes:
> > - v2: remove the extra example and fix node label
> >
> > This patch conflicts with Nicolas' one: "dt-bindings: sdhci-of-at91: add
> > the microchip,sdcal-inverted property". Let me know which one has to be
> > rebased or you can handle it.
> >
> > Ludovic
> >
> >
> > .../devicetree/bindings/mmc/sdhci-atmel.txt | 15 ++++++++++++---
> > 1 file changed, 12 insertions(+), 3 deletions(-)
> >
> > diff --git a/Documentation/devicetree/bindings/mmc/sdhci-atmel.txt b/Documentation/devicetree/bindings/mmc/sdhci-atmel.txt
> > index 1b662d7171a0..5d541ad4d4eb 100644
> > --- a/Documentation/devicetree/bindings/mmc/sdhci-atmel.txt
> > +++ b/Documentation/devicetree/bindings/mmc/sdhci-atmel.txt
> > @@ -5,17 +5,26 @@ Documentation/devicetree/bindings/mmc/mmc.txt and the properties used by the
> > sdhci-of-at91 driver.
> >
> > Required properties:
> > -- compatible: Must be "atmel,sama5d2-sdhci".
> > +- compatible: Must be "atmel,sama5d2-sdhci" or "microchip,sam9x60-sdhci".
> > - clocks: Phandlers to the clocks.
> > -- clock-names: Must be "hclock", "multclk", "baseclk";
> > +- clock-names: Must be "hclock", "multclk", "baseclk" for
> > + "atmel,sama5d2-sdhci".
> > + Must be "hclock", "multclk" for "microchip,sam9x60-sdhci".
> > +
> > +Optional properties:
> > +- assigned-clocks: The same with "multclk".
> > +- assigned-clock-rates The rate of "multclk" in order to not rely on the
> > + gck configuration set by previous components.
> >
> >
> > Example:
> >
> > -sdmmc0: sdio-host@a0000000 {
> > +mmc0: sdio-host@a0000000 {
> > compatible = "atmel,sama5d2-sdhci";
> > reg = <0xa0000000 0x300>;
> > interrupts = <31 IRQ_TYPE_LEVEL_HIGH 0>;
> > clocks = <&sdmmc0_hclk>, <&sdmmc0_gclk>, <&main>;
> > clock-names = "hclock", "multclk", "baseclk";
> > + assigned-clocks = <&sdmmc0_gclk>;
> > + assigned-clock-rates = <480000000>;
> > };
> > --
> > 2.23.0
> >