This patch series adds support for the Samsung Galaxy Express SGH-I437.
Currently the following things work on this phone: UART, eMMC, SD Card, and
USB.
version 3:
- Added Ack
- Fixed compatible in qcom,usb-hs-phy.yaml. `make dt_binding_check dtbs_check`
no longer complains about USB
- Fixed formatting in qcom-msm8960.dtsi and qcom-msm8960-samsung-expressatt.dts
- Fixed the spi1_default node in qcom-msm8960-samsung-expressatt.dts.
`make dt_binding_check dtbs_check` no longer complains
version 2:
- Combined patch 1 into patch 4, as the sleep_clk label is specifically needed
for the USB node.
- Reformatted the commit messages to align with the style used in other commit
messages that modify the same files.
- Included a cover letter to provide an overview of the patch series.
- Slight refactoring of the device tree source (DTS) file.
Rudraksha Gupta (4):
dt-bindings: arm: qcom: Add Samsung Galaxy Express
dt-bindings: phy: qcom,usb-hs-phy: Add compatible
ARM: dts: qcom: msm8960: Add USB node
ARM: dts: qcom: Add Samsung Galaxy Express support
.../devicetree/bindings/arm/qcom.yaml | 1 +
.../bindings/phy/qcom,usb-hs-phy.yaml | 5 +-
arch/arm/boot/dts/Makefile | 1 +
.../dts/qcom-msm8960-samsung-expressatt.dts | 331 ++++++++++++++++++
arch/arm/boot/dts/qcom-msm8960.dtsi | 34 +-
5 files changed, 370 insertions(+), 2 deletions(-)
create mode 100644 arch/arm/boot/dts/qcom-msm8960-samsung-expressatt.dts
--
2.34.1
Add the required nodes to support USB on the MSM8960 SoC. As it's very
similar to the APQ8064 SoC, the nodes are almost identical
Add a label to sleep_clk for the USB node to reference
Signed-off-by: Rudraksha Gupta <[email protected]>
---
arch/arm/boot/dts/qcom-msm8960.dtsi | 34 ++++++++++++++++++++++++++++-
1 file changed, 33 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/qcom-msm8960.dtsi b/arch/arm/boot/dts/qcom-msm8960.dtsi
index 2a668cd535cc..581b3ab5c4ca 100644
--- a/arch/arm/boot/dts/qcom-msm8960.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8960.dtsi
@@ -3,6 +3,7 @@
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/qcom,gcc-msm8960.h>
+#include <dt-bindings/reset/qcom,gcc-msm8960.h>
#include <dt-bindings/clock/qcom,lcc-msm8960.h>
#include <dt-bindings/mfd/qcom-rpm.h>
#include <dt-bindings/soc/qcom,gsbi.h>
@@ -71,7 +72,7 @@ pxo_board: pxo_board {
clock-output-names = "pxo_board";
};
- sleep_clk {
+ sleep_clk: sleep_clk {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <32768>;
@@ -370,5 +371,36 @@ gsbi1_spi: spi@16080000 {
status = "disabled";
};
};
+
+ usb1: usb@12500000 {
+ compatible = "qcom,ci-hdrc";
+ reg = <0x12500000 0x200>,
+ <0x12500200 0x200>;
+ interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc USB_HS1_XCVR_CLK>, <&gcc USB_HS1_H_CLK>;
+ clock-names = "core", "iface";
+ assigned-clocks = <&gcc USB_HS1_XCVR_CLK>;
+ assigned-clock-rates = <60000000>;
+ resets = <&gcc USB_HS1_RESET>;
+ reset-names = "core";
+ phy_type = "ulpi";
+ ahb-burst-config = <0>;
+ phys = <&usb_hs1_phy>;
+ phy-names = "usb-phy";
+ #reset-cells = <1>;
+ status = "disabled";
+
+ ulpi {
+ usb_hs1_phy: phy {
+ compatible = "qcom,usb-hs-phy-msm8960",
+ "qcom,usb-hs-phy";
+ clocks = <&sleep_clk>, <&cxo_board>;
+ clock-names = "sleep", "ref";
+ resets = <&usb1 0>;
+ reset-names = "por";
+ #phy-cells = <0>;
+ };
+ };
+ };
};
};
--
2.34.1
Adds qcom,usb-hs-phy-msm8960 compatible
Signed-off-by: Rudraksha Gupta <[email protected]>
---
Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.yaml | 5 ++++-
1 file changed, 4 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.yaml
index aa97478dd016..63b6914993fe 100644
--- a/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.yaml
+++ b/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.yaml
@@ -13,7 +13,9 @@ if:
properties:
compatible:
contains:
- const: qcom,usb-hs-phy-apq8064
+ items:
+ - const: qcom,usb-hs-phy-apq8064
+ - const: qcom,usb-hs-phy-msm8960
then:
properties:
resets:
@@ -40,6 +42,7 @@ properties:
- qcom,usb-hs-phy-apq8064
- qcom,usb-hs-phy-msm8226
- qcom,usb-hs-phy-msm8916
+ - qcom,usb-hs-phy-msm8960
- qcom,usb-hs-phy-msm8974
- const: qcom,usb-hs-phy
--
2.34.1
Add a compatible for Samsung Galaxy Express SGH-I437.
Signed-off-by: Rudraksha Gupta <[email protected]>
Acked-by: Conor Dooley <[email protected]>
---
Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index d9dd25695c3d..133d69b2b73d 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -191,6 +191,7 @@ properties:
- items:
- enum:
- qcom,msm8960-cdp
+ - samsung,expressatt
- const: qcom,msm8960
- items:
--
2.34.1
Add a very basic device tree file for the Samsung Galaxy Express SGH-I437.
Currently, the following things work: UART, eMMC, SD Card, and USB.
Signed-off-by: Rudraksha Gupta <[email protected]>
---
arch/arm/boot/dts/Makefile | 1 +
.../dts/qcom-msm8960-samsung-expressatt.dts | 331 ++++++++++++++++++
2 files changed, 332 insertions(+)
create mode 100644 arch/arm/boot/dts/qcom-msm8960-samsung-expressatt.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 59829fc90315..12c90f263142 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1081,6 +1081,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-msm8916-samsung-grandmax.dtb \
qcom-msm8916-samsung-serranove.dtb \
qcom-msm8960-cdp.dtb \
+ qcom-msm8960-samsung-expressatt.dtb \
qcom-msm8974-lge-nexus5-hammerhead.dtb \
qcom-msm8974-sony-xperia-rhine-amami.dtb \
qcom-msm8974-sony-xperia-rhine-honami.dtb \
diff --git a/arch/arm/boot/dts/qcom-msm8960-samsung-expressatt.dts b/arch/arm/boot/dts/qcom-msm8960-samsung-expressatt.dts
new file mode 100644
index 000000000000..13e85c287498
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-msm8960-samsung-expressatt.dts
@@ -0,0 +1,331 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/input/input.h>
+
+#include "qcom-msm8960.dtsi"
+#include <dt-bindings/reset/qcom,gcc-msm8960.h>
+
+/ {
+ model = "Samsung Galaxy Express SGH-I437";
+ compatible = "samsung,expressatt", "qcom,msm8960";
+ chassis-type = "handset";
+
+ aliases {
+ serial0 = &gsbi5_serial;
+ mmc0 = &sdcc1; /* SDCC1 eMMC slot */
+ mmc1 = &sdcc3; /* SDCC3 SD card slot */
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&gsbi5 {
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+ status = "okay";
+};
+
+&gsbi5_serial {
+ status = "okay";
+};
+
+&sdcc1 {
+ vmmc-supply = <&pm8921_l5>;
+ status = "okay";
+};
+
+&sdcc3 {
+ vmmc-supply = <&pm8921_l6>;
+ vqmmc-supply = <&pm8921_l7>;
+ status = "okay";
+};
+
+&gsbi1 {
+ qcom,mode = <GSBI_PROT_SPI>;
+ pinctrl-0 = <&spi1_default>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&gsbi1_spi {
+ status = "okay";
+};
+
+&msmgpio {
+ spi1_default: spi1-default-state {
+ mosi-pins {
+ pins = "gpio6";
+ function = "gsbi1";
+ drive-strength = <12>;
+ bias-disable;
+ };
+
+ miso-pins {
+ pins = "gpio7";
+ function = "gsbi1";
+ drive-strength = <12>;
+ bias-disable;
+ };
+
+ cs-pins {
+ pins = "gpio8";
+ function = "gsbi1";
+ drive-strength = <12>;
+ bias-disable;
+ output-low;
+ };
+
+ clk-pins {
+ pins = "gpio9";
+ function = "gsbi1";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ };
+};
+
+&rpm {
+ regulators {
+ compatible = "qcom,rpm-pm8921-regulators";
+ vin_lvs1_3_6-supply = <&pm8921_s4>;
+ vin_lvs2-supply = <&pm8921_s4>;
+ vin_lvs4_5_7-supply = <&pm8921_s4>;
+ vdd_ncp-supply = <&pm8921_l6>;
+ vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+ vdd_l21_l23_l29-supply = <&pm8921_s8>;
+ vdd_l24-supply = <&pm8921_s1>;
+ vdd_l25-supply = <&pm8921_s1>;
+ vdd_l27-supply = <&pm8921_s7>;
+ vdd_l28-supply = <&pm8921_s7>;
+
+ /* Buck SMPS */
+ pm8921_s1: s1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ qcom,switch-mode-frequency = <3200000>;
+ bias-pull-down;
+ };
+
+ pm8921_s2: s2 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ qcom,switch-mode-frequency = <1600000>;
+ bias-pull-down;
+ };
+
+ pm8921_s3: s3 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1150000>;
+ qcom,switch-mode-frequency = <4800000>;
+ bias-pull-down;
+ };
+
+ pm8921_s4: s4 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ qcom,switch-mode-frequency = <1600000>;
+ bias-pull-down;
+ qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
+ };
+
+ pm8921_s7: s7 {
+ regulator-min-microvolt = <1150000>;
+ regulator-max-microvolt = <1150000>;
+ qcom,switch-mode-frequency = <3200000>;
+ bias-pull-down;
+ };
+
+ pm8921_s8: s8 {
+ regulator-always-on;
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
+ qcom,switch-mode-frequency = <1600000>;
+ bias-pull-down;
+ };
+
+ /* PMOS LDO */
+ pm8921_l1: l1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ bias-pull-down;
+ };
+
+ pm8921_l2: l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ bias-pull-down;
+ };
+
+ pm8921_l3: l3 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3300000>;
+ bias-pull-down;
+ };
+
+ pm8921_l4: l4 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ bias-pull-down;
+ };
+
+ pm8921_l5: l5 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ bias-pull-down;
+ };
+
+ pm8921_l6: l6 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ bias-pull-down;
+ };
+
+ pm8921_l7: l7 {
+ regulator-always-on;
+ regulator-min-microvolt = <1850000>;
+ regulator-max-microvolt = <2950000>;
+ bias-pull-down;
+ };
+
+ pm8921_l8: l8 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3100000>;
+ bias-pull-down;
+ };
+
+ pm8921_l9: l9 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ bias-pull-down;
+ };
+
+ pm8921_l10: l10 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ bias-pull-down;
+ };
+
+ pm8921_l11: l11 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3300000>;
+ bias-pull-down;
+ };
+
+ pm8921_l12: l12 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ bias-pull-down;
+ };
+
+ pm8921_l14: l14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ bias-pull-down;
+ };
+
+ pm8921_l15: l15 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ bias-pull-down;
+ };
+
+ pm8921_l16: l16 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3000000>;
+ bias-pull-down;
+ };
+
+ pm8921_l17: l17 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ bias-pull-down;
+ };
+
+ pm8921_l18: l18 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1500000>;
+ bias-pull-down;
+ };
+
+ pm8921_l21: l21 {
+ regulator-min-microvolt = <1900000>;
+ regulator-max-microvolt = <1900000>;
+ bias-pull-down;
+ };
+
+ pm8921_l22: l22 {
+ regulator-min-microvolt = <2750000>;
+ regulator-max-microvolt = <2750000>;
+ bias-pull-down;
+ };
+
+ pm8921_l23: l23 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ bias-pull-down;
+ };
+
+ pm8921_l24: l24 {
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1150000>;
+ bias-pull-down;
+ };
+
+ pm8921_l25: l25 {
+ regulator-always-on;
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ bias-pull-down;
+ };
+
+ /* Low Voltage Switch */
+ pm8921_lvs1: lvs1 {
+ bias-pull-down;
+ };
+
+ pm8921_lvs2: lvs2 {
+ bias-pull-down;
+ };
+
+ pm8921_lvs3: lvs3 {
+ bias-pull-down;
+ };
+
+ pm8921_lvs4: lvs4 {
+ bias-pull-down;
+ };
+
+ pm8921_lvs5: lvs5 {
+ bias-pull-down;
+ };
+
+ pm8921_lvs6: lvs6 {
+ bias-pull-down;
+ };
+
+ pm8921_lvs7: lvs7 {
+ bias-pull-down;
+ };
+
+ pm8921_ncp: ncp {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ qcom,switch-mode-frequency = <1600000>;
+ };
+ };
+};
+
+&usb_hs1_phy {
+ v3p3-supply = <&pm8921_l3>;
+ v1p8-supply = <&pm8921_l4>;
+};
+
+&usb1 {
+ dr_mode = "otg";
+ status = "okay";
+};
--
2.34.1
On Sun, 04 Jun 2023 02:30:19 -0400, Rudraksha Gupta wrote:
> Adds qcom,usb-hs-phy-msm8960 compatible
>
> Signed-off-by: Rudraksha Gupta <[email protected]>
> ---
> Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.yaml | 5 ++++-
> 1 file changed, 4 insertions(+), 1 deletion(-)
>
My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
on your patch (DT_CHECKER_FLAGS is new in v5.13):
yamllint warnings/errors:
dtschema/dtc warnings/errors:
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.example.dtb: phy: resets: [[4294967295, 10], [1, 0]] is too long
From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.example.dtb: phy: reset-names:0: 'por' was expected
From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.example.dtb: phy: reset-names: ['phy', 'por'] is too long
From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.yaml
doc reference errors (make refcheckdocs):
See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/[email protected]
The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.
If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:
pip3 install dtschema --upgrade
Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.
On 04/06/2023 08:30, Rudraksha Gupta wrote:
> Adds qcom,usb-hs-phy-msm8960 compatible
>
> Signed-off-by: Rudraksha Gupta <[email protected]>
> ---
> Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.yaml | 5 ++++-
> 1 file changed, 4 insertions(+), 1 deletion(-)
>
> diff --git a/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.yaml
> index aa97478dd016..63b6914993fe 100644
> --- a/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.yaml
> +++ b/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.yaml
> @@ -13,7 +13,9 @@ if:
> properties:
> compatible:
> contains:
> - const: qcom,usb-hs-phy-apq8064
> + items:
> + - const: qcom,usb-hs-phy-apq8064
> + - const: qcom,usb-hs-phy-msm8960
I have no clue what you want to achieve here. You break the bindings.
It does not look like you tested the bindings, at least after quick
look. Please run `make dt_binding_check` (see
Documentation/devicetree/bindings/writing-schema.rst for instructions).
Maybe you need to update your dtschema and yamllint.
Best regards,
Krzysztof
On Sun Jun 4, 2023 at 3:23 AM EDT, Rob Herring wrote:
>
> On Sun, 04 Jun 2023 02:30:19 -0400, Rudraksha Gupta wrote:
> > Adds qcom,usb-hs-phy-msm8960 compatible
> >
> > Signed-off-by: Rudraksha Gupta <[email protected]>
> > ---
> > Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.yaml | 5 ++++-
> > 1 file changed, 4 insertions(+), 1 deletion(-)
> >
>
> My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
> on your patch (DT_CHECKER_FLAGS is new in v5.13):
>
> yamllint warnings/errors:
>
> dtschema/dtc warnings/errors:
> /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.example.dtb: phy: resets: [[4294967295, 10], [1, 0]] is too long
> From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.yaml
> /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.example.dtb: phy: reset-names:0: 'por' was expected
> From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.yaml
> /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.example.dtb: phy: reset-names: ['phy', 'por'] is too long
> From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.yaml
>
> doc reference errors (make refcheckdocs):
>
> See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/[email protected]
>
> The base for the series is generally the latest rc1. A different dependency
> should be noted in *this* patch.
I see. Why is it off the latest rc1 and not off the latest commit?
>
> If you already ran 'make dt_binding_check' and didn't see the above
> error(s), then make sure 'yamllint' is installed and dt-schema is up to
> date:
>
> pip3 install dtschema --upgrade
>
> Please check and re-submit after running the above command yourself. Note
> that DT_SCHEMA_FILES can be set to your schema file to speed up checking
> your schema. However, it must be unset to test all examples with your schema.
Thanks. I didn't see these errors as I was only looking for expressatt
binding errors.
On Sun Jun 4, 2023 at 6:30 AM EDT, Krzysztof Kozlowski wrote:
> On 04/06/2023 08:30, Rudraksha Gupta wrote:
> > Adds qcom,usb-hs-phy-msm8960 compatible
> >
> > Signed-off-by: Rudraksha Gupta <[email protected]>
> > ---
> > Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.yaml | 5 ++++-
> > 1 file changed, 4 insertions(+), 1 deletion(-)
> >
> > diff --git a/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.yaml
> > index aa97478dd016..63b6914993fe 100644
> > --- a/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.yaml
> > +++ b/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.yaml
> > @@ -13,7 +13,9 @@ if:
> > properties:
> > compatible:
> > contains:
> > - const: qcom,usb-hs-phy-apq8064
> > + items:
> > + - const: qcom,usb-hs-phy-apq8064
> > + - const: qcom,usb-hs-phy-msm8960
>
> I have no clue what you want to achieve here. You break the bindings.
When I added the USB node to the msm8960 dtsi file, I got similar
messages for the expressatt/cdp that Rob mentioned in his email reply:
phy: resets: [[25, 0]] is too short
phy: reset-names:0: 'phy' was expected
phy: reset-names: ['por'] is too short
I will send an updated patch soon that addresses this.
>
> It does not look like you tested the bindings, at least after quick
> look. Please run `make dt_binding_check` (see
> Documentation/devicetree/bindings/writing-schema.rst for instructions).
> Maybe you need to update your dtschema and yamllint.
>
> Best regards,
> Krzysztof
Sorry. I was only looking for expressatt errors/warnings and failed to
see the other errors/warnings in the sea of text.
On 06/06/2023 04:48, Rudraksha Gupta wrote:
ted patch soon that addresses this.
>
>>
>> It does not look like you tested the bindings, at least after quick
>> look. Please run `make dt_binding_check` (see
>> Documentation/devicetree/bindings/writing-schema.rst for instructions).
>> Maybe you need to update your dtschema and yamllint.
>>
>> Best regards,
>> Krzysztof
> Sorry. I was only looking for expressatt errors/warnings and failed to
> see the other errors/warnings in the sea of text.
https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/
Best regards,
Krzysztof