From: Anson Huang <[email protected]>
i.MX8MM can reuse i.MX8MQ's reset driver, update the compatible
property and related info to support i.MX8MM.
Signed-off-by: Anson Huang <[email protected]>
---
Changes since V2:
- Add separate line for i.MX8MM in case anything different later for i.MX8MM.
---
Documentation/devicetree/bindings/reset/fsl,imx7-src.txt | 6 ++++--
1 file changed, 4 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt b/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt
index 13e0951..c2489e4 100644
--- a/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt
+++ b/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt
@@ -8,6 +8,7 @@ Required properties:
- compatible:
- For i.MX7 SoCs should be "fsl,imx7d-src", "syscon"
- For i.MX8MQ SoCs should be "fsl,imx8mq-src", "syscon"
+ - For i.MX8MM SoCs should be "fsl,imx8mm-src", "fsl,imx8mq-src", "syscon"
- reg: should be register base and length as documented in the
datasheet
- interrupts: Should contain SRC interrupt
@@ -46,5 +47,6 @@ Example:
For list of all valid reset indices see
-<dt-bindings/reset/imx7-reset.h> for i.MX7 and
-<dt-bindings/reset/imx8mq-reset.h> for i.MX8MQ
+<dt-bindings/reset/imx7-reset.h> for i.MX7,
+<dt-bindings/reset/imx8mq-reset.h> for i.MX8MQ and
+<dt-bindings/reset/imx8mq-reset.h> for i.MX8MM
--
2.7.4
From: Anson Huang <[email protected]>
i.MX8MM can reuse i.MX8MQ's src driver, add "fsl,imx8mq-src" as
src's fallback compatible to enable it.
Signed-off-by: Anson Huang <[email protected]>
Reviewed-by: Philipp Zabel <[email protected]>
---
No changes.
---
arch/arm64/boot/dts/freescale/imx8mm.dtsi | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/freescale/imx8mm.dtsi b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
index 172bb6f..1870c89 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
@@ -520,7 +520,7 @@
};
src: reset-controller@30390000 {
- compatible = "fsl,imx8mm-src", "syscon";
+ compatible = "fsl,imx8mm-src", "fsl,imx8mq-src", "syscon";
reg = <0x30390000 0x10000>;
interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
#reset-cells = <1>;
--
2.7.4
Hi Anson,
On Thu, 2019-07-04 at 17:44 +0800, [email protected] wrote:
> From: Anson Huang <[email protected]>
>
> i.MX8MM can reuse i.MX8MQ's reset driver, update the compatible
> property and related info to support i.MX8MM.
>
> Signed-off-by: Anson Huang <[email protected]>
> ---
> Changes since V2:
> - Add separate line for i.MX8MM in case anything different later for i.MX8MM.
> ---
> Documentation/devicetree/bindings/reset/fsl,imx7-src.txt | 6 ++++--
> 1 file changed, 4 insertions(+), 2 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt b/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt
> index 13e0951..c2489e4 100644
> --- a/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt
> +++ b/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt
> @@ -8,6 +8,7 @@ Required properties:
> - compatible:
> - For i.MX7 SoCs should be "fsl,imx7d-src", "syscon"
> - For i.MX8MQ SoCs should be "fsl,imx8mq-src", "syscon"
> + - For i.MX8MM SoCs should be "fsl,imx8mm-src", "fsl,imx8mq-src", "syscon"
> - reg: should be register base and length as documented in the
> datasheet
> - interrupts: Should contain SRC interrupt
> @@ -46,5 +47,6 @@ Example:
>
>
> For list of all valid reset indices see
> -<dt-bindings/reset/imx7-reset.h> for i.MX7 and
> -<dt-bindings/reset/imx8mq-reset.h> for i.MX8MQ
> +<dt-bindings/reset/imx7-reset.h> for i.MX7,
> +<dt-bindings/reset/imx8mq-reset.h> for i.MX8MQ and
> +<dt-bindings/reset/imx8mq-reset.h> for i.MX8MM
The last line is misleading, as that file contains reset indices that
are invalid for i.MX8MM.
regards
Philipp
Hi, Philipp
> On Thu, 2019-07-04 at 17:44 +0800, [email protected] wrote:
> > From: Anson Huang <[email protected]>
> >
> > i.MX8MM can reuse i.MX8MQ's reset driver, update the compatible
> > property and related info to support i.MX8MM.
> >
> > Signed-off-by: Anson Huang <[email protected]>
> > ---
> > Changes since V2:
> > - Add separate line for i.MX8MM in case anything different later for
> i.MX8MM.
> > ---
> > Documentation/devicetree/bindings/reset/fsl,imx7-src.txt | 6 ++++--
> > 1 file changed, 4 insertions(+), 2 deletions(-)
> >
> > diff --git a/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt
> > b/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt
> > index 13e0951..c2489e4 100644
> > --- a/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt
> > +++ b/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt
> > @@ -8,6 +8,7 @@ Required properties:
> > - compatible:
> > - For i.MX7 SoCs should be "fsl,imx7d-src", "syscon"
> > - For i.MX8MQ SoCs should be "fsl,imx8mq-src", "syscon"
> > + - For i.MX8MM SoCs should be "fsl,imx8mm-src", "fsl,imx8mq-src",
> "syscon"
> > - reg: should be register base and length as documented in the
> > datasheet
> > - interrupts: Should contain SRC interrupt @@ -46,5 +47,6 @@ Example:
> >
> >
> > For list of all valid reset indices see
> > -<dt-bindings/reset/imx7-reset.h> for i.MX7 and
> > -<dt-bindings/reset/imx8mq-reset.h> for i.MX8MQ
> > +<dt-bindings/reset/imx7-reset.h> for i.MX7,
> > +<dt-bindings/reset/imx8mq-reset.h> for i.MX8MQ and
> > +<dt-bindings/reset/imx8mq-reset.h> for i.MX8MM
>
> The last line is misleading, as that file contains reset indices that are invalid
> for i.MX8MM.
What is your suggestion about this line? Just NOT change it? Or adding a new file
imx8mm-reset.h but still use the IMX8MQ_RESET_ as prefix ? Or keep what I changed, but
adding some comments in those macros that i.MX8MM does NOT support?
Thanks,
Anson.
>
> regards
> Philipp
Hi Anson,
On Fri, 2019-07-05 at 00:26 +0000, Anson Huang wrote:
> Hi, Philipp
>
> > On Thu, 2019-07-04 at 17:44 +0800, [email protected] wrote:
> > > From: Anson Huang <[email protected]>
> > >
> > > i.MX8MM can reuse i.MX8MQ's reset driver, update the compatible
> > > property and related info to support i.MX8MM.
> > >
> > > Signed-off-by: Anson Huang <[email protected]>
> > > ---
> > > Changes since V2:
> > > - Add separate line for i.MX8MM in case anything different later for
> >
> > i.MX8MM.
> > > ---
> > > Documentation/devicetree/bindings/reset/fsl,imx7-src.txt | 6 ++++--
> > > 1 file changed, 4 insertions(+), 2 deletions(-)
> > >
> > > diff --git a/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt
> > > b/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt
> > > index 13e0951..c2489e4 100644
> > > --- a/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt
> > > +++ b/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt
> > > @@ -8,6 +8,7 @@ Required properties:
> > > - compatible:
> > > - For i.MX7 SoCs should be "fsl,imx7d-src", "syscon"
> > > - For i.MX8MQ SoCs should be "fsl,imx8mq-src", "syscon"
> > > + - For i.MX8MM SoCs should be "fsl,imx8mm-src", "fsl,imx8mq-src",
> >
> > "syscon"
> > > - reg: should be register base and length as documented in the
> > > datasheet
> > > - interrupts: Should contain SRC interrupt @@ -46,5 +47,6 @@ Example:
> > >
> > >
> > > For list of all valid reset indices see
> > > -<dt-bindings/reset/imx7-reset.h> for i.MX7 and
> > > -<dt-bindings/reset/imx8mq-reset.h> for i.MX8MQ
> > > +<dt-bindings/reset/imx7-reset.h> for i.MX7,
> > > +<dt-bindings/reset/imx8mq-reset.h> for i.MX8MQ and
> > > +<dt-bindings/reset/imx8mq-reset.h> for i.MX8MM
> >
> > The last line is misleading, as that file contains reset indices that are invalid
> > for i.MX8MM.
>
> What is your suggestion about this line?
I would prefer to add an imx8mm-reset.h with only the existing reset
bits, using the IMX8MM_RESET_ prefix. That would make it easy to spot
errors in the dtsi (anything starting with IMX8MQ_ is potentially
wrong).
> Just NOT change it?
The change is good in principle. It just should point to an imx8mm-
reset.h with only the existing resets on i.MX8MM, or imx8mq-reset.h
should be modified to actually make clear which resets are valid on
i.MX8MM.
> Or adding a new file imx8mm-reset.h but still use the IMX8MQ_RESET_ as
> prefix ?
I don't think you should redefine the same macros in imx8mm-reset.h. In
this case using IMX8MM_RESET_ would be better.
> Or keep what I changed, but adding some comments in those macros that
> i.MX8MM does NOT support?
That would be acceptable as well.
regards
Philipp
Hi, Philipp
> On Fri, 2019-07-05 at 00:26 +0000, Anson Huang wrote:
> > Hi, Philipp
> >
> > > On Thu, 2019-07-04 at 17:44 +0800, [email protected] wrote:
> > > > From: Anson Huang <[email protected]>
> > > >
> > > > i.MX8MM can reuse i.MX8MQ's reset driver, update the compatible
> > > > property and related info to support i.MX8MM.
> > > >
> > > > Signed-off-by: Anson Huang <[email protected]>
> > > > ---
> > > > Changes since V2:
> > > > - Add separate line for i.MX8MM in case anything different later
> > > > for
> > >
> > > i.MX8MM.
> > > > ---
> > > > Documentation/devicetree/bindings/reset/fsl,imx7-src.txt | 6
> > > > ++++--
> > > > 1 file changed, 4 insertions(+), 2 deletions(-)
> > > >
> > > > diff --git
> > > > a/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt
> > > > b/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt
> > > > index 13e0951..c2489e4 100644
> > > > --- a/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt
> > > > +++ b/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt
> > > > @@ -8,6 +8,7 @@ Required properties:
> > > > - compatible:
> > > > - For i.MX7 SoCs should be "fsl,imx7d-src", "syscon"
> > > > - For i.MX8MQ SoCs should be "fsl,imx8mq-src", "syscon"
> > > > + - For i.MX8MM SoCs should be "fsl,imx8mm-src", "fsl,imx8mq-src",
> > >
> > > "syscon"
> > > > - reg: should be register base and length as documented in the
> > > > datasheet
> > > > - interrupts: Should contain SRC interrupt @@ -46,5 +47,6 @@ Example:
> > > >
> > > >
> > > > For list of all valid reset indices see
> > > > -<dt-bindings/reset/imx7-reset.h> for i.MX7 and
> > > > -<dt-bindings/reset/imx8mq-reset.h> for i.MX8MQ
> > > > +<dt-bindings/reset/imx7-reset.h> for i.MX7,
> > > > +<dt-bindings/reset/imx8mq-reset.h> for i.MX8MQ and
> > > > +<dt-bindings/reset/imx8mq-reset.h> for i.MX8MM
> > >
> > > The last line is misleading, as that file contains reset indices
> > > that are invalid for i.MX8MM.
> >
> > What is your suggestion about this line?
>
> I would prefer to add an imx8mm-reset.h with only the existing reset bits,
> using the IMX8MM_RESET_ prefix. That would make it easy to spot errors in
> the dtsi (anything starting with IMX8MQ_ is potentially wrong).
>
> > Just NOT change it?
>
> The change is good in principle. It just should point to an imx8mm- reset.h with
> only the existing resets on i.MX8MM, or imx8mq-reset.h should be modified to
> actually make clear which resets are valid on i.MX8MM.
>
> > Or adding a new file imx8mm-reset.h but still use the IMX8MQ_RESET_ as
> > prefix ?
>
> I don't think you should redefine the same macros in imx8mm-reset.h. In this
> case using IMX8MM_RESET_ would be better.
>
> > Or keep what I changed, but adding some comments in those macros that
> > i.MX8MM does NOT support?
>
> That would be acceptable as well.
I will go this way, thanks for suggestion.
Anson.
>
> regards
> Philipp