This patch series intends to add CAN self wakeup support. The CAN
controller can parse stop-mode property from device tree to enable self
wakeup feature.
Dong Aisheng (2):
can: flexcan: Add self wakeup support
Documentation: can: flexcan: Add stop-mode property to device tree
.../bindings/net/can/fsl-flexcan.txt | 8 +
drivers/net/can/flexcan.c | 141 ++++++++++++++++--
2 files changed, 140 insertions(+), 9 deletions(-)
--
2.17.1
From: Dong Aisheng <[email protected]>
If wakeup is enabled, enter stop mode, else enter disabled mode.
Self wake can only work on stop mode.
Starting from IMX6, the flexcan stop mode control bits is SoC specific,
move it out of IP driver and parse it from devicetree.
Signed-off-by: Dong Aisheng <[email protected]>
Signed-off-by: Joakim Zhang <[email protected]>
---
drivers/net/can/flexcan.c | 141 +++++++++++++++++++++++++++++++++++---
1 file changed, 132 insertions(+), 9 deletions(-)
diff --git a/drivers/net/can/flexcan.c b/drivers/net/can/flexcan.c
index 3813f6708201..9e05d01da85f 100644
--- a/drivers/net/can/flexcan.c
+++ b/drivers/net/can/flexcan.c
@@ -19,12 +19,17 @@
#include <linux/delay.h>
#include <linux/interrupt.h>
#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/list.h>
+#include <linux/mfd/syscon.h>
+#include <linux/mfd/syscon/imx6q-iomuxc-gpr.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/of_device.h>
#include <linux/platform_device.h>
#include <linux/pm_runtime.h>
#include <linux/regulator/consumer.h>
+#include <linux/regmap.h>
#define DRV_NAME "flexcan"
@@ -132,7 +137,8 @@
(FLEXCAN_ESR_ERR_BUS | FLEXCAN_ESR_ERR_STATE)
#define FLEXCAN_ESR_ALL_INT \
(FLEXCAN_ESR_TWRN_INT | FLEXCAN_ESR_RWRN_INT | \
- FLEXCAN_ESR_BOFF_INT | FLEXCAN_ESR_ERR_INT)
+ FLEXCAN_ESR_BOFF_INT | FLEXCAN_ESR_ERR_INT | \
+ FLEXCAN_ESR_WAK_INT)
/* FLEXCAN interrupt flag register (IFLAG) bits */
/* Errata ERR005829 step7: Reserve first valid MB */
@@ -255,6 +261,14 @@ struct flexcan_devtype_data {
u32 quirks; /* quirks needed for different IP cores */
};
+struct flexcan_stop_mode {
+ struct regmap *gpr;
+ u8 req_gpr;
+ u8 req_bit;
+ u8 ack_gpr;
+ u8 ack_bit;
+};
+
struct flexcan_priv {
struct can_priv can;
struct can_rx_offload offload;
@@ -272,6 +286,7 @@ struct flexcan_priv {
struct clk *clk_per;
const struct flexcan_devtype_data *devtype_data;
struct regulator *reg_xceiver;
+ struct flexcan_stop_mode stm;
/* Read and Write APIs */
u32 (*read)(void __iomem *addr);
@@ -392,6 +407,22 @@ static void flexcan_clks_disable(const struct flexcan_priv *priv)
clk_disable_unprepare(priv->clk_per);
}
+static inline void flexcan_enter_stop_mode(struct flexcan_priv *priv)
+{
+ /* enable stop request */
+ if (priv->devtype_data->quirks & FLEXCAN_QUIRK_USE_OFF_TIMESTAMP)
+ regmap_update_bits(priv->stm.gpr, priv->stm.req_gpr,
+ 1 << priv->stm.req_bit, 1 << priv->stm.req_bit);
+}
+
+static inline void flexcan_exit_stop_mode(struct flexcan_priv *priv)
+{
+ /* remove stop request */
+ if (priv->devtype_data->quirks & FLEXCAN_QUIRK_USE_OFF_TIMESTAMP)
+ regmap_update_bits(priv->stm.gpr, priv->stm.req_gpr,
+ 1 << priv->stm.req_bit, 0);
+}
+
static inline int flexcan_transceiver_enable(const struct flexcan_priv *priv)
{
if (!priv->reg_xceiver)
@@ -955,6 +986,10 @@ static int flexcan_chip_start(struct net_device *dev)
reg_mcr |= FLEXCAN_MCR_FEN |
FLEXCAN_MCR_MAXMB(priv->tx_mb_idx);
}
+
+ /* enable self wakeup */
+ reg_mcr |= FLEXCAN_MCR_WAK_MSK | FLEXCAN_MCR_SLF_WAK;
+
netdev_dbg(dev, "%s: writing mcr=0x%08x", __func__, reg_mcr);
priv->write(reg_mcr, ®s->mcr);
@@ -1240,6 +1275,56 @@ static void unregister_flexcandev(struct net_device *dev)
unregister_candev(dev);
}
+static int flexcan_of_parse_stop_mode(struct platform_device *pdev)
+{
+ struct net_device *dev = platform_get_drvdata(pdev);
+ struct device_node *np = pdev->dev.of_node;
+ struct device_node *node;
+ struct flexcan_priv *priv;
+ phandle phandle;
+ u32 out_val[5];
+ int ret;
+
+ if (!np)
+ return -EINVAL;
+
+ /* stop mode property format is:
+ * <&gpr req_gpr req_bit ack_gpr ack_bit>.
+ */
+ ret = of_property_read_u32_array(np, "stop-mode", out_val, 5);
+ if (ret) {
+ dev_dbg(&pdev->dev, "no stop-mode property\n");
+ return ret;
+ }
+ phandle = *out_val;
+
+ node = of_find_node_by_phandle(phandle);
+ if (!node) {
+ dev_dbg(&pdev->dev, "could not find gpr node by phandle\n");
+ return PTR_ERR(node);
+ }
+
+ priv = netdev_priv(dev);
+ priv->stm.gpr = syscon_node_to_regmap(node);
+ if (IS_ERR(priv->stm.gpr)) {
+ dev_dbg(&pdev->dev, "could not find gpr regmap\n");
+ return PTR_ERR(priv->stm.gpr);
+ }
+
+ of_node_put(node);
+
+ priv->stm.req_gpr = out_val[1];
+ priv->stm.req_bit = out_val[2];
+ priv->stm.ack_gpr = out_val[3];
+ priv->stm.ack_bit = out_val[4];
+
+ dev_dbg(&pdev->dev, "gpr %s req_gpr 0x%x req_bit %u ack_gpr 0x%x ack_bit %u\n",
+ node->full_name, priv->stm.req_gpr,
+ priv->stm.req_bit, priv->stm.ack_gpr,
+ priv->stm.ack_bit);
+ return 0;
+}
+
static const struct of_device_id flexcan_of_match[] = {
{ .compatible = "fsl,imx6q-flexcan", .data = &fsl_imx6q_devtype_data, },
{ .compatible = "fsl,imx28-flexcan", .data = &fsl_imx28_devtype_data, },
@@ -1271,6 +1356,7 @@ static int flexcan_probe(struct platform_device *pdev)
struct flexcan_regs __iomem *regs;
int err, irq;
u32 clock_freq = 0;
+ int wakeup = 1;
reg_xceiver = devm_regulator_get(&pdev->dev, "xceiver");
if (PTR_ERR(reg_xceiver) == -EPROBE_DEFER)
@@ -1400,6 +1486,16 @@ static int flexcan_probe(struct platform_device *pdev)
devm_can_led_init(dev);
+ if (priv->devtype_data->quirks & FLEXCAN_QUIRK_USE_OFF_TIMESTAMP) {
+ err = flexcan_of_parse_stop_mode(pdev);
+ if (err) {
+ wakeup = 0;
+ dev_dbg(&pdev->dev, "failed to parse stop-mode\n");
+ }
+ }
+
+ device_set_wakeup_capable(&pdev->dev, wakeup);
+
pm_runtime_put(&pdev->dev);
dev_info(&pdev->dev, "device registered (reg_base=%p, irq=%d)\n",
@@ -1437,10 +1533,18 @@ static int __maybe_unused flexcan_suspend(struct device *device)
int err = 0;
if (netif_running(dev)) {
- err = flexcan_chip_disable(priv);
- if (err)
- return err;
- err = pm_runtime_force_suspend(device);
+ /* if wakeup is enabled, enter stop mode
+ * else enter disabled mode.
+ */
+ if (device_may_wakeup(device)) {
+ enable_irq_wake(dev->irq);
+ flexcan_enter_stop_mode(priv);
+ } else {
+ err = flexcan_chip_disable(priv);
+ if (err)
+ return err;
+ err = pm_runtime_force_suspend(device);
+ }
netif_stop_queue(dev);
netif_device_detach(dev);
@@ -1461,10 +1565,12 @@ static int __maybe_unused flexcan_resume(struct device *device)
netif_device_attach(dev);
netif_start_queue(dev);
- err = pm_runtime_force_resume(device);
- if (err)
- return err;
- err = flexcan_chip_enable(priv);
+ if (!device_may_wakeup(device)) {
+ err = pm_runtime_force_resume(device);
+ if (err)
+ return err;
+ err = flexcan_chip_enable(priv);
+ }
}
return err;
}
@@ -1489,10 +1595,27 @@ static int __maybe_unused flexcan_runtime_resume(struct device *device)
return 0;
}
+static int __maybe_unused flexcan_noirq_resume(struct device *device)
+{
+ struct net_device *dev = dev_get_drvdata(device);
+ struct flexcan_priv *priv = netdev_priv(dev);
+
+ /* exit stop mode during noirq stage avoid continuously entering
+ * wakeup ISR before CAN resume back.
+ */
+ if (netif_running(dev) && device_may_wakeup(device)) {
+ disable_irq_wake(dev->irq);
+ flexcan_exit_stop_mode(priv);
+ }
+
+ return 0;
+}
+
static const struct dev_pm_ops flexcan_pm_ops = {
SET_SYSTEM_SLEEP_PM_OPS(flexcan_suspend, flexcan_resume)
SET_RUNTIME_PM_OPS(flexcan_runtime_suspend, flexcan_runtime_resume,
NULL)
+ SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(NULL, flexcan_noirq_resume)
};
static struct platform_driver flexcan_driver = {
--
2.17.1
From: Dong Aisheng <[email protected]>
The FlexCAN controller can parse the stop-mode property to enable CAN
self wakeup feature.
Signed-off-by: Dong Aisheng <[email protected]>
Signed-off-by: Joakim Zhang <[email protected]>
---
Documentation/devicetree/bindings/net/can/fsl-flexcan.txt | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt
index bfc0c433654f..b5ccfc9c14fb 100644
--- a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt
+++ b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt
@@ -24,6 +24,14 @@ Optional properties:
if this property is present then controller is assumed to be big
endian.
+- stop-mode: register bits of stop mode control, the format is
+ <&gpr req_gpr req_bit ack_gpr ack_bit>.
+ gpr is the phandle to general purpose register node.
+ req_gpr is the gpr register offset of CAN stop request.
+ req_bit is the bit offset of CAN stop request.
+ ack_gpr is the gpr register offset of CAN stop acknowledge.
+ ack_bit is the bit offset of CAN stop acknowledge.
+
Example:
can@1c000 {
--
2.17.1
On Tue, Oct 23, 2018 at 05:17:10AM +0000, Joakim Zhang wrote:
> From: Dong Aisheng <[email protected]>
>
> The FlexCAN controller can parse the stop-mode property to enable CAN
> self wakeup feature.
>
> Signed-off-by: Dong Aisheng <[email protected]>
> Signed-off-by: Joakim Zhang <[email protected]>
> ---
> Documentation/devicetree/bindings/net/can/fsl-flexcan.txt | 8 ++++++++
> 1 file changed, 8 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt
> index bfc0c433654f..b5ccfc9c14fb 100644
> --- a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt
> +++ b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt
> @@ -24,6 +24,14 @@ Optional properties:
> if this property is present then controller is assumed to be big
> endian.
>
> +- stop-mode: register bits of stop mode control, the format is
Should have a vendor prefix: fsl,stop-mode
> + <&gpr req_gpr req_bit ack_gpr ack_bit>.
> + gpr is the phandle to general purpose register node.
> + req_gpr is the gpr register offset of CAN stop request.
> + req_bit is the bit offset of CAN stop request.
> + ack_gpr is the gpr register offset of CAN stop acknowledge.
> + ack_bit is the bit offset of CAN stop acknowledge.
> +
> Example:
>
> can@1c000 {
> --
> 2.17.1
>
-----Original Message-----
From: Rob Herring [mailto:[email protected]]
Sent: 2018??10??25?? 7:57
To: Joakim Zhang <[email protected]>
Cc: [email protected]; [email protected]; [email protected]; [email protected]; [email protected]; [email protected]; dl-linux-imx <[email protected]>; A.s. Dong <[email protected]>
Subject: Re: [PATCH V1 2/2] Documentation: can: flexcan: Add stop-mode property to device tree
On Tue, Oct 23, 2018 at 05:17:10AM +0000, Joakim Zhang wrote:
> From: Dong Aisheng <[email protected]>
>
> The FlexCAN controller can parse the stop-mode property to enable CAN
> self wakeup feature.
>
> Signed-off-by: Dong Aisheng <[email protected]>
> Signed-off-by: Joakim Zhang <[email protected]>
> ---
> Documentation/devicetree/bindings/net/can/fsl-flexcan.txt | 8
> ++++++++
> 1 file changed, 8 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt
> b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt
> index bfc0c433654f..b5ccfc9c14fb 100644
> --- a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt
> +++ b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt
> @@ -24,6 +24,14 @@ Optional properties:
> if this property is present then controller is assumed to be big
> endian.
>
> +- stop-mode: register bits of stop mode control, the format is
Should have a vendor prefix: fsl,stop-mode
Okay, I will add it. Thanks a lot!
Best Regards,
Joakim Zhang
> + <&gpr req_gpr req_bit ack_gpr ack_bit>.
> + gpr is the phandle to general purpose register node.
> + req_gpr is the gpr register offset of CAN stop request.
> + req_bit is the bit offset of CAN stop request.
> + ack_gpr is the gpr register offset of CAN stop acknowledge.
> + ack_bit is the bit offset of CAN stop acknowledge.
> +
> Example:
>
> can@1c000 {
> --
> 2.17.1
>